advertisement
VTX30
Two-Channel Guitar Amplifier with Digital Signal Processing
User’s Guide
VTX30
Two-Channel Guitar Amplifier with DSP
TABLE OF CONTENTS:
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
The Top Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .4,5
The Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .5
The DSP Section . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . .7
Technical Specifications . . . . . . . . . . . . . . .back cover
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this device not expressly approved by SLM Electronics could void the user’s authority to operate the equipment under FCC rules.
Declaration of Conformity
Manufacturer’s Name: SLM Electronics
Corporate Headquarters: 1901 Congressional Drive, St. Louis, Missouri 63146
Primary Production Facility: 700 Hwy 202 W, Yellville, Arkansas, 72687
Product Type: Audio Amplifier
Products meet the regulations for compliance marking under:
ETL standards UL6500, UL60065, or UL813
CSA standards E60065 or C22.2 No.1-M90
CE safety standard EN60065
CE EMC standards EN55103 or EN55013 and EN61000
C-tick designation Level 2, ABN #56748810738, ARBN# N222
KETI standard K60065 (limited model approval)
Compliance Support Contact: SLM Electronics, Attn: R&D Compliance Engineer
1901 Congressional Drive, St Louis, Missouri, 63146 • Tel.: 314-569-0141, Fax: 314-569-0175
VTX30
Two-Channel Guitar Amplifier with DSP
Congratulations
and thank you for choosing the Crate VTX30 Guitar Amplifier with Digital Signal Processing. This rugged amplifier features a Clean channel with a three-band EQ and level control, and a Solo channel with our patented FlexWave technology, Gain, Level and Shape control. An easy to operate DSP section lets you dial in a variety of digital effects including reverbs, delays, octave and wah-wahs. RCA input jacks allow connection of a CD or tape player for practicing with your favorite music, while the Headphones jack allows you to practice in private. The top-mounted electronic tuner allows you to get tuned and stay in tune any time the amplifier is on.
In order to get the most out of your new amplifier, we strongly urge you to read this guide before you begin playing.
And thank you for choosing C TE .
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS-
TURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA
LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
IMPORTANT SAFETY INSTRUCTIONS
• READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
• DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
PROPER OPERATION, THIS UNIT REQUIRES 3” (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR
FLOW PROVISIONS IN THE CABINET.
• DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
• CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
• ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
• PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
• UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
• ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR
SAFE OPERATION AND TO AVOID INJURY.
• WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE..
• SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
• OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PRO-
TECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
=
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
=
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
3
VTX30
Two-Channel Guitar Amplifier with DSP
The Top Panel:
INPUT GAIN
SOLO
SHAPE LEVEL LEVEL
CLEAN
LOW MID HIGH
DSP
LEVEL DELAY
FLANGER 1
FLANGER 2
DOUBLER
REVERB
SOLO CLEAN
POWER
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1: INPUT: Use this 1/4” jack to connect your guitar to the amplifier by means of a shielded instrument cable.
SOLO CHANNEL: A high gain channel giving you sounds from a slight edge to serious overdrive.
2: GAIN: Use this control to adjust the amount of distortion for the Solo channel.
3: SHAPE: Use this control to adjust the tone of the Solo channel.
4: LEVEL: Use this control to adjust the output level of the Solo channel.
5: SOLO/CLEAN: Use this switch to select the Solo or Clean channel. With the switch in the out position, the Clean channel is selected. When the switch is depressed, the Solo channel is selected.
CLEAN CHANNEL: A normal gain channel designed to give you crystal clear sounds to medium distortion.
6: LEVEL: Use this control to adjust the output level of the clean channel.
7: LOW: Use this control to adjust the low frequency level of the clean channel.
8: MID: Use this control to adjust the midrange frequency level of the clean channel.
9: HIGH: Use this control to adjust the high frequency level of the clean channel.
10: DSP LEVEL: Use this control to adjust the level of the selected digital effect. The DSP effects can be turned on and off by using a footswitch (#17, rear panel).
11: (DSP MODE): Use this control to select one of the 16 built-in digital effects. The nomenclature around the control is further explained in the chart on page 6.
12: CD INPUT: Use these RCA jacks to connect the output from a CD payer or tape deck to the amplifier. The signal at these jacks is summed into a mono signal which is sent to the internal power amp circuit. Use the CD or tape player’s output level control to adjust the signal for the proper mix with your guitar.
13: HEADPHONES: Use this jack to connect headphones to the amplifier. The internal speaker is disconnected when headphones are used.
CAUTION: To avoid possible damage to your hearing, do not use headphones for extended periods of time at extremely loud levels.
4
VTX30
Two-Channel Guitar Amplifier with DSP
14: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off
(bottom of the switch depressed). The switch illuminates when the amplifier is turned on.
15: TUNER: The electronic tuner is active whenever the amplifier is turned on, providing constant, “real-time” tuning. The bottom row of LEDs indicate which note (string) is being tuned. The top row of LEDs provides directional queues to facilitate quick and precise tuning of your instrument. The indicated note
(string) is properly tuned when only the center
LED is illuminated.
The Bottom Panel (not shown):
16: EXTENSION SPEAKER: Use this jack to connect the amplifier to an external speaker. The internal speaker is disconnected when this jack is used. The impedance of the external speaker must be 4 ohms or greater.
WARNING: Do not attempt to use headphones in the Speaker jack! Permanent hearing damage could result!
17: FOOTSWITCH: Use this jack to connect the 1/4” stereo plug on the cable of a two-button footswitch (such as the Crate CFP2). This allows you to remotely switch between the
Clean and Solo channels and turn the DSP function on and off.
18: POWER CORD: The grounded power cord should only be plugged into a grounded power outlet that meets all applicable electrical codes and is compatible with the voltage, power, and frequency requirements stated on the bottom panel. Do not attempt to defeat the safety ground connection.
5
The DSP Section:
VTX30
Two-Channel Guitar Amplifier with DSP
Use the DSP control to select one of the 16 built-in digital effects. Use the DSP Level control to adjust the amount of selected effect. In the fully counter clockwise position there will be no effect applied. As you rotate the Level control clockwise the amount of effect increases.
The chart below describes each of the 16 positions of the selector, starting at the 12:00 position and working clockwise.
DSP
LEVEL DELAY
FLANGER 1
FLANGER 2
CHORUS 1
T-WAH
I-WAH
DOUBLER
REVERB
FLANGER 1: slow deep flange w/reverb
FLANGER 2: flange w/reverb & delay
CHORUS 1: slow tremolo chorus w/reverb
CHORUS 2: chorus w/reverb & delay
ROTARY: rotating speaker effect
OCTAVE: adds signal one octave below
T-WAH: touch wah effect
I-WAH: inverse wah effect
DOUBLER: adds second signal slightly out of sync
REVERB: small room reverb medium room reverb large room reverb concert hall reverb
DELAY: short slapback w/small room reverb medium delay w/large room reverb slow deep flange w/reverb
6
VTX30
Two-Channel Guitar Amplifier with DSP
System Block Diagram:
TUNER
INPUT
BUFFER
A BC D EF G
CLEAN
LEVEL LOW MID HIGH
SOLO
GAIN SHAPE LEVEL
SOLO/
CLEAN
FOOTSWITCH
JACK
POWER
AMP
SPEAKER
EXTENSION
SPEAKER
DSP
LEVEL
MODE
CD
INPUT
7
VTX30
Two-Channel Guitar Amplifier with DSP
VTX30 TECHNICAL SPECIFICATIONS:
Output Power Rating >30W RMS @ 5% THD, 4
Ω
, 120 VAC
Gain Solo Ch
Clean Ch
98dB +/-6dB @ 1kHz
42dB +/-6dB @ 1kHz
Maximum Input Signal Accepted
Tone Controls
Speaker Size and Rating
Low
Mid
High
6 volts peak-to-peak min. @ 1kHz
20dB range @ 80Hz
12dB range @ 900Hz
18dB range @ 10kHz
10” Crate Custom Design 4 ohm
Power Requirements
Size and Weight
120 VAC, 60Hz, 50VA
100/115VAC, 50/60Hz, 50VA
230VAC, 50/60Hz, 50VA
16-1/2” H x 11-3/4” W x 9-1/4” D, 20 lbs.
The VTX30 is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications and information in this manual are subject to change without notice.
www.crateamps.com
@2004 SLM Electronics, a division of St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
47-718-01 • 062104
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project