Crosley Radio CR02-002A User's Manual

25-2-08
WARRANTY
CR02-002A
Crosley Radio Products are warranted against defects in material and
workmanship for a period of 90 days beginning from the date of sale to the
original purchaser.
Should the unit fail under normal usage during the 90 day warranty period, a
request for RETURN AUTHORIZATION (R.A.) must be made by the original
customer before returning the unit. Call Crosley Radio customer service for
Return Authorization at (502) 583-4246 from 9 AM to 5 PM (EST) Monday to
Friday.
Dock Clock
Instruction Manual
Upon receiving the RETURN AUTHORIZATION number from the Customer
Service Department, properly pack your unit in its original packaging. Include
any adapters, parts, & accessories which were originally provided with the
product, along with a check or money order for $19.95 made out to Crosley
Radio to cover the handling and return postage. Display the R.A. # on the
outside of the carton and ship PREPAID via standard UPS or its equivalent.
TUNE
ATTN: RETURNS DEP'T
2001 PRODUCTION DRIVE
BAY 2 & 3
LOUISVILLE, KY 40299
VOLU
ME
DOW
N
UP
IPOD
/AUX
DO
RAD
IO
AM/F
M
CROSLEY RADIO assumes no responsibility for units sent without prior Return Authorization.
The purchaser’s bill of sale is the only proof of warranty entitlement and must accompany the unit.
The warranty does not cover damage due to acts of nature, accident, misuse, abuse, negligence, commercial
use or modification of, or to any part of the product. This warranty does not cover damage due to improper
operation or maintenance, connection to improper voltage supply, or attempted repair by anyone other than
a facility authorized by Crosley Radio to service the product. This warranty does not cover products sold
AS IS or consumables (such as fuses or batteries). This warranty is valid only in the United States.
UP
CLO
CK A
DJ.
SLE
EP
WAK
E
-TO
OFF
ALM
. SE
T
ALM
. ON
/OFF
ALM
.RES
ET
This warranty gives the purchaser specified legal rights in addition to any rights which may vary from state
to state.
In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty"
which in no way compromises Crosley Radio‚ high standards of Quality and Workmanship.
12
910-274300-0010-100
22-2-08
General
Troubleshooting :
Symptom
Possible Problem
Solution
Does not turn on
AC adaptor isn’t plugged into a
working wall socket or not plugged
into the power supply jack on back
of the unit
Plug the AC adaptor into a working wall socket and
plug the connector into the supply jack on the unit
Doesn’t respond
Requires a reset
If unit is plugged in and doesn’t respond, try
resetting the unit by following these steps:
a) remove iPod from dock
b) unplug unit from power source
c) remove back up batteries
d) wait 1 hour, then resume use
iPod does not dock
properly
Battery Low icon always
flashing
iPod does not respond
to the unit/iPod is playing
but no sound comes out
Using no or wrong iPod insert
Make sure the dock insert is the proper fit for your
iPod
iPod didn’t install properly
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on
your iPod. Then reseat it in the dock.
Batteries are weak
Replace with new batteries
Batteries were not installed properly
Check to make sure polarity(+ and - ends)matches
the diagram in the battery compartment
iPod is not installed properly
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on
your iPod. Then reseat it in the dock.
Your iPod software is too old
Upgrade on your iPod. For details visit
http://www.apple.com/ipod/download
iPod is locked up/plays but no
sound comes out
Check the volume setting. Make sure your iPod is
working properly before docking into the unit.
Please refer to your iPod manual for details. See
above for software upgrade information.
you may need to reset your iPod. To do so:
a) Toggle the Hold switch to hold position, then off.
b) Press and hold the Menu and center Select
button at the same time until apple logo
appears. You may need to repeat this step.
Using 1st or 2nd generation iPod,
iPod Shuffle or other devices.
It cannot control those iPods or other devices.
Battery weak
Replace current battery with new battery
Remote Control is not pointed
toward it remote sensor
Point the Remote Control towards the remote
sensor (to the left of the display), move within
10 feet of the unit.
Radio/iPod performance is
erratic
It is reaction to external interference
Move unit away from potential sources of external
interference such as computers, modems, wireless
devices(routers) or fluorescent light
No sound from unit
Volume is set too low on unit
Make sure volume is turned up
iPod didn’t charge up
iPod is not installed properly
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and
on your iPod. Then reseat it in the dock.
iPod is locked up/frozen
Please make sure your iPod is working properly
before docking into the unit. Please refer to your
iPod manual for details.
Remote Control didn’t
work
iPod battery has problem
10
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
Specification
Frequency Range
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
:
:
Power Supply
:
Power Consumption :
Antennas
:
:
Speaker
:
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
AM 530 - 1710 KHz
FM 87.5 - 107.9 MHz
AC Adaptor DC15V 1.3A
25W
External the telescopic antenna for FM
built-in ferrite bar for AM
3” 4ohm 7W x 1
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
Operation
Getting Started
Listening to Your iPod
Using the Alarm
Setting the Alarm
1
2
Press and hold the Alarm Set Button (11) until
the alarm time flashes.
Playing and charging your iPod
1
Turn the Tune Knob (1) to set the desired alarm
time.
2
NOTE:
a PM indicator appears when the time is set to PM,
there is no AM indicator.
3
4
3
Press Alarm Set Button (11) again. Alarm is now
set. An alarm clock icon will show on the display
as well as the alarm source icon.
4
Press the Wake To Button (10) repeatedly to select
the desired wake to source: iPod, Radio or Buzzer.
NOTE:
Before turning the unit off, set the volume to the level
you wish to wake to.
Arming and Disarming Alarm (Turn
Alarm Function ON and OFF)
1
Press the Alarm On/Off Button (12) to arm or
disarm alarm function. When armed, alarm
icon appears in display.
Snooze
1
Press the Snooze/Dimmer Button (15/30) after
the alarm sounds. The alarm will be silenced and
come on again 9 minutes later. Snooze can be
pressed several times during the 1 hour alarm
cycle.
Place the proper dock plate (not supplied) for
your iPod in the Dock (14), then gently dock
your iPod. When docked, the iPod will begin
charging. The iPod will not overcharge.
Press the iPod Button (5) to play iPod, and
again to pause.
Adjust the volume level to the desired listening
level by turning the Volume Knob (4).
Press the Alarm Reset/Power Off Button (13) to
turn the unit and the iPod off.
Radio Operation
Unit Controls
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Tune Knob
Remote sensor
LCD Display
Volume Knob
(iPod/Aux)/Play Button
Radio Button
(BAND)AM/FM Button
Clock Adjust Button
Sleep Button
Wake To Button
Alarm Set Button
Alarm ON/OFF Button
Alarm Reset/Power off Button
iPod Dock
Snooze/Dimmer Button
Speaker
1
2
3
4
TUNE
DOWN
VOLUME
UP
DOWN
UP
OFF
RADIO
IPOD/AUX
5
6
AM/FM
7
CLOCK ADJ.
8
WAKE-TO
SLEEP
9
10
ALM. SET
11
ALM. ON/OFF
12
ALM.RESET
13
Tuning and Playing the Radio
1
Press the Radio Button (29) to select radio
play mode.
2
Press the AM/FM Select Button (7/25) to select
AM or FM radio band.
3
Turn the Tune Knob (1) to tune radio to desired
station.
4
Adjust the volume level to desire level by turning
the Volume Knob (4).
5
SNOOZE/DIMMER
14
15
16
Press the Alarm Reset/Power Off Button (13) to
turn the radio off.
iPod and Radio using the Remote control
Press the Next track Button (24) or Previous track
Button (28) when iPod is playing,or hold to scan
current playing track.In Radio mode, press to tune
station,hold to scan Radio station.
8
5
IMPORTANT SAFETY INSTRUCTION
1.
2.
3.
4.
5.
PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS
THAT ARE APPLICABLE TO YOUR EQUIPMENT
Read Instructions - All the safety and operating instructions should be read before the product is operated.
Retain instructions - The safety and operating instructions should be retained for future reference.
Heed Warnings - All warnings on the product and in the operating Instructions should be adhered to.
Follow Instructions - All operating and use instructions should be followed.
Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must not be blocked
or covered, The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built - in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power source indicated on the marking label,
if you are not sure of the type of power supply to your home. Consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet try reversing the plug, If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power - Cord Protection - Power - supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
13. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage
to the product due to lightning and power - line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
15. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short - out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
17. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions;
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. Wall or ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators. Heat registers, stoves, or other
products (including amplifiers) that produce heat.
General
Troubleshooting :
Symptom
Possible Problem
Solution
No AM band radio is very
noisy
Unit not getting good signal
Move the main unit/iPod and rotate it for best
reception
Sound is distorted
Volume level is set too high
Decrease the volume
Sound source is distorted
If the iPod original sound source(MP3) is old or of
poor quality, distortion and noise are easily noticed
with high-power speakers. Try a different audio
source such as a music CD.
If you are using an external sound source like
older generation of iPod or iPod Shuffle, try
reducing the output volume on the device itself.
Also try turning bass boost OFF.
Unit/adaptor gets warm
after extended play at
high volume
This is normal
Turn unit off for a while or lower volume
PROBLEMS?
5G iPod(iPod with video) or iPod nano
RESET YOUR iPOD (as per apple website)
(will not affect music on your iPod)
1. Move the Hold switch ON and OFF(slide it to Hold, then turn it off again)
2. Press and hold the MENU + centre SELECT button until the Apple logo
appears (about 6-10 seconds). You may need to repeat this step.
NOTE : Please make sure that your iPod has the latest firmware. Check
your iPod manual or the Apple website(www.apple.com) and follow
instructions on how to upgrade firmware for you iPod.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful intereference to radio or
television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
11
Welcome
Thank you for purchasing the Crosley Dock Clock
(CR02-002A). Before operating this unit, please
read this manual thoroughly and retain it for future
reference.
About This Manual
Instructions in this manual describe the control
functions of the Dock Clock(CR02-002A).
Included in the package:
Dock Clock
Remote Control
3.5mm stereo cable
Operation
Table of Contents
Getting Started
Control Locators....................... 5-6
Setting the Clock...................... 7
Battery Backup......................... 7
Operation
Using the Alarm.......................
Radio Operation.......................
Listening to Your iPod.............
Remote Control.......................
Sleep Mode.............................
Auxiliary Input..........................
Remote
Telescopic Antenna
The Remote Control controls basic unit functions as
well as basic iPod functions when the iPod is docked
in the unit. Be sure to aim the remote towards the
LCD display.
Extend the Telescopic Antenna (17) (on back of unit)
fully for best reception. Do not strip, alter or
attach to other antennas.
Install/Replace the Remote Control Battery
8
8
8
9
9
9
General
The remote control battery is already installed at the
factory. When the remote control stops operating or
its range seems reduced, replace the battery with
a new one.
1
2
Troubleshooting Guide............ 10-11
Warranty................................... 12
The battery door is located on the back end of
the unit.
Squeeze notched tab A while pulling battery
door latch B to release the battery door latch
and take out the battery holder.
Sleep Mode
Sleep mode lets you sleep to your iPod
or the radio, gradually lowering the volume
until the unit shuts off at the selected time.
1
Press the Sleep Button (9) to select the
amount of time before it turns off : 120,90,60,30
or 15 minutes.
2
Turn the Volume knob (4) to set the sleep
volume (this volume setting is separate from
your standard volume setting).
A
Battery
door
latch
Auxiliary Input Jack
B
3
Insert a “CR2025“ 3-volt lithium battery. Make
sure the polarity (the +and - side of the battery)
is correct.
4
Replace the battery holder back in the remote
control.
NOTE :
PLEASE RESPECT THE ENVIRONMENT:
DISCARD BATTERIES PROPERLY.
CAUTION: When replacing the battery, replace only
with the same or equivalent type.
Using the Auxiliary Input Jack
1
A 3.5mm stereo cable comes with your radio.
You can use it to play non-docking iPod’s or
other audio devices by connecting one end of
the cable to the Aux In Jack (20) and the other
end plugged into the line out jack of the selected
device. Make sure there is no iPod docked in
your unit before using the Aux In Jack. Press
the iPod/Aux Button (5). AUX will appear on
the display and the device is ready to use.
Using Dimmer
1
Press the Snooze/Dimmer Button (15/30) during
normal operation to adjust brightness of LCD
display.
9
Getting Started
Getting Started
17
18
19
20
21
18
17
Unit Controls
1
Telescopic Antenna
Battery Compartment
AC Adaptor Jack
Aux In Jack
Headphone Jack
ANTENNA
DC15V 1.3A
Plug the included AC adaptor cable into the
AC Adaptor Jack (19) and the other end into a
standard 120V wall socket. It does not operate
on batteries.
AUX IN
Setting the Clock and Date
19 20 21
31
Remote Controls
22
23
24
25
26
27
28
29
30
31
Power ON/OFF Button
Volume Up + Button
Next track
(Band)AM/FM Button
Play/Pause
Button
Volume Down - Button
Previous track
Radio Button
Snooze/Dimmer Button
AC Adaptor
22
VOL
27
24
29
25
1
Press and hold the Clock Adjust Button (8).
The clock Display will flash.
1
Remove the Battery Compartment Cover (18)
from the back of the unit.
2
Turn the Tune Knob (1) until the current time is
displayed (in 12hour mode, a PM indicator
appears when time is set to PM; there is no AM
indicator.)
2
Install two new AA batteries in the correct position
as shown inside the battery cover.
3
Reinstall the Battery Compartment Cover (18).
3
Press the Clock Adjust Button (8) to accept the
time. The year display will flash.
4
NOTE :
Do not different batteries
Do not mix old and new batteries
Turn the Tune Knob (1) to adjust the year and
press the Clock Adjust Button (8). The date
display will flash.
5
Turn the Tune Knob (1) to adjust the date and
press the Clock Adjust Button (8). The setting
is complete.
AM/FM
26
30
SNOOZE
DIMMER
6
The Crosley Dock Clock uses a battery backup system
to maintain your clock and alarm settings during a
power outage. In the event of a power outage, the
battery backup will save your time and alarm settings
until power is restored. The display light will also turn
off until power is restored. To utilize the battery backup,
you must install two AA batteries. The battery backup
will not operate unless batteries are installed. To install
batteries, follow the instructions below.
23
28
RADIO
Battery Back Up
Power Source
iPOD
7