advertisement
2 ch output
INSTRUCTION MANUAL
DVD1072 mp3
IMPORTANT
READ THESE INSTRUCTIONS
BEFORE USE AND RETAIN
FOR FUTURE REFERENCE.
PROGRESSIVE SCAN
SAFETY INFORMATION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTION
:
To reduce the risk of fire and electric shock, do not remove the cover (or back) of the unit. Refer servicing only to qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and servicing instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
IMPORTANT SAFEGUARDS
In addition to the careful attention devoted to quality standards in the manufacture of your video product, safety is a major factor in the design of every instrument.
However, safety is your responsibility, too. This sheet lists important information that will help to assure your enjoyment and proper use of the video product and accessory equipment. Please read them carefully before operation and using your video product.
8. Do not place naked flame sources, such as candles, on the appliance.
9. Do not locate the appliance or cord near heat sources such as radiators, heaters, air ducts or direct sunlight.
10. Do not block any of the ventilation openings. Ensure that vents are not covered by newspapers, tablecloths, curtains, etc. Do not install in a tight-fitting cabinet.
11. Do not insert or allow foreign objects to enter any grille openings.
12. Do not run the cord under carpeting. Instead, arrange the cord away from traffic areas where it will not become a trip hazard.
13. To disconnect the appliance, turn the appliance off, switch off the power outlet and remove the plug from the power outlet.
14. Do not misuse the cord. Never carry the appliance by the cord or pull to disconnect it from the outlet. Instead, grasp the plug and pull to disconnect.
15. Do not operate the appliance if it has a damaged cord or plug; after the appliance malfunctions; or has been dropped or damaged in any way. Consult Singer for examination.
16. Use of controls or adjustments, or performance of procedures other than those specified herein, may result in hazardous radiation exposure.
Caution
Do not open do not attempt to repair, disassemble or
modify this appliance.
Dangerous high voltages exist inside this appliance.
This appliance is only to be serviced by Singer Service
Technician. There are no user-serviceable parts inside.
Do not look at laser pick-up directly. Do not touch
the lens.
Installation
Read all instructions carefully, even if you are familiar with the appliance.
1. This appliance is not intended for use by children or infirm persons without supervision.
2. Children should be prevented from playing with the appliance.
3. This appliance should be placed on a dry, level surface before it is operated.
4. INDOOR USE ONLY this appliance is not intended for outdoor use.
5. Do not expose this appliance to rain or moisture. Do not immerse the appliance in water or any other liquid.
6. Do not place items filled with liquids, such as vases, on the appliance. Do not expose the appliance to dripping or splashing liquids.
7. This appliance is not intended for use in bathrooms, laundry areas or similar moist locations. Never locate this appliance in the immediate surroundings of, or where it may fall into, a bath, basin, washtub, shower or swimming pool.
Installation Warnings
Ventilation Slots and openings in the case are provided for ventilation to ensure reliable operation of the video product and to protect it from overheating.
These openings must not the blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or heat register. This product should not be placed in a built-in installation such as a bookcase or rack, unless proper ventilation is provided or the video product manufacturer instructions have been followed.
Outdoor Antenna Grounding If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and builtup static charges. ANSI/NFPA
No. 70-1984 provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Power Lines An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching or approaching such power lines or circuits, as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer.
Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power line surges.
SAFETY INFORMATION
Compulsory Warnings
If the supply cord is damaged, it must be replaced by Singer service Technicion, in order to avoid a hazard. This product has not been designed for any uses other than those specified in this booklet.
Laser Safety
This compact disc player is classified as a CLASS 1
LASER PRODUCT.
Only qualified service personnel should remove the
cover or attempt to service this device due to
possible eye injury.
Invisible laser radiation when open and interlock
failed or defeated.
Avoid direct exposure to beam.
FEATURES
DVD, CD, MP3, Picture CD compatible
CD-R, CD-RW capable
TV format:
4:3 / 16:9 screen format select
Video output:
Composite Video output
S-Video output
YPbPr output
Audio output:
Down-mix stereo output
DVD features:
Multi Subtitle select
Multi Language select
Multi Angle select
Other features:
On screen control menu
Digital zooming
Slow motion forward
Child lock
Auto screen saver
CONTENTS
Page
WARNING
IMPORTANT NOTICE
FEATURES
ESSENTIAL SETUP ............................................. 1
INTRODUCTION ................................................................... 2
About DVD ................................................................... 3
About the player ........................................................... 4
Remote control ............................................................. 4-5
SYSTEM CONNECTION ............................................... 6
GETTING STARTED
Play a disc ..................................................................... 7
Screen saver ................................................................. 8
FUNCTION BUTTONS
[ Power] , [ Open / Close ] , [ Play / Pause / Stop ] .................. 9
[ Skip ] , [ Slow ] , [ Select an item ] , [ Title/ Menu , Clear ]
..................
10-11
[ NumberkeyPad ] , [ Angle ] , [ Subtitle ] , [ Audio ] .................. 12-13
[ V-Mode ] , [ Reset ] , [ Search a desired section ] ................................... 14-15
[ Repeat ] , [ A-B ] , [ Zoom ] , [ Mute ] , [ Shufflle ] , [ PBC ] , [ Channel ]16-18
[ Program ] , [ Return ] , [ Mark ] .............................................. 19-20
ON SCREEN DISPLAY
OSD DVD mode ............................................................ 21
OSD CD mode .............................................................. 21
OSD Mp3 mode ............................................................ 22
SETUP MENU
LANGUAGE MENU ....................................................... 23
OSD Menu / Subtitle / Audio / DVD Menu
VIDEO MENU ................................................................ 24
TV Shape
AUDIO MENU ............................................................... 24
Digital output
RATING MENU ............................................................. 24
Password / Rating
TROUBLE SHOOTING ........................................ 25-26
SPECIFICATIONS ............................................... 27
ESSENTIAL SETUP
Video outputs
The player is equipped with the following video output ports:
Composite Video and S-Video always active, does not need setting.
... ... ...
... ... ...
Language
Video Audio Rating
... ... ...
... ... ...
1
INTRODUCTION
THE REMOTE CONTROL
Loading batteries to the remote control
Remove the battery compartment cover.
Load two AAA (UM-4 or R03) batteries into the
battery compartment.
Make sure that the batteries have been inserted
in the correct polarities matching to the symbols
+, - marked in the battery compartment. Close
the battery compartment cover.
When replacing batteries, replace both batteries.
Do not mix new and used batteries operating
together, otherwise, the operation lifetime will
be much shorter than normal.
Remove the batteries if the unit will not be used
for a prolonged period of time.
The remote control transmits a directional
infrared beam.Be sure to aim the remote
control directly at the infrared sensor of the
unit during operation.
If the sensor has been covered or there is a
large object between the remote control and
the sensor, the sensor will not respond.
The sensor may not able to receive the
remote signal when it is exposed to direct
sunlight or a strong artificial light (fluorescent
or strobe light). In this case, change the
direction of the light or reposition the unit to
avoid direct lighting.
30 30
UM-4
UM-4
Within approximately
6 meter (20 feet)
BE ENVIRONMENTALLY FRIENDLY
Do not dispose of batteries as normal rubbish. Be environmentally friendly, dispose of batteries following the Government's regulation.
2
INTRODUCTION
About DVD
DVD (Digital Versatile Disc) is a digital video medium under the MPEG II format, featuring a variety of revolutionary entertainment capabilities. The MPEG II video compression technology provides capacity for an excellent picture of minimum 500 lines resolution on screen, up to 8 language soundtracks, up to 9 views from different camera angles and up to 32 language subtitles (provided the DVD disc itself supports these features).
Select a DVD disc
DVD Region Code
DVD discs and DVD players are manufactured under the worldwide agreed DVD Regional
Code System that the player will operate only with corresponding disc of the same Regional
Code.
Region code Region
1 Canada, USA
Disc information
Disc types
Recording
Method
DVD
Digital / MPEG II
Capacity
Single-layer / Single side
4.7GB = 2 hr
Single-layer / Double sides
8.5GB = 4 hr
Double-layers / Single side
9.4GB = 4.5 hr
Double-layers / Double sides
17GB = 8 hr
12cm / 8cm Disc size
Horizontal
Resolution
Sub-titles
500 lines up
32
CD
Digital
650MB=74min
12cm / 8cm
-
2
3
4
5
6
Europe (incl. Poland, Romania, The Czech republic), Japan, Middle East (incl. Saudi
Arabia, Egypt, Iran, South Africa)
East Asia (incl. Hong Kong, T aiwan, South
Korea),
South-East Asia
Australia, Caribbean, Central
America, Mexico,
New Zealand
Africa, Former Soviet Union, India, North
Korea, Pakistan, Turkmenistan
China
& South
Sound tracks
8
-
1
Care of disc
Symbol
Hold the disc with fingers. Hold the disc's outer edge and/or the center spindle hole. Do not touch the disc surface.
REMARK
Some features contained in this DVD player are related to the
DVD disc's software.
Some features cannot be performed if the disc does not support the feature,or requires special settings.
Check the features printed on the disc's packing or follow the instructions of the Disc's on screen menu.
Do not bend or press the disc. Do NOT expose the disc to direct sunlight or heating sources.
Store discs in cabinet vertically , in dry condition.
Prevent exposure to:
Direct sunlight
Heat or exhaust from a heating device.
Clean the disc surface with a soft, dry cleaning cloth.
Wipe the disc surface gently , radically , from center toward the outer edge.
Do not applythinner, alcohol chemical solvent, or sprays when cleaning. Such cleaning fluids will permanently damage the disc surface.
3
INTRODUCTION
About the player
Front panel
6
5
6
L/R
FWD
REV
STOP
OPEN/CLOSE
POWER
Back panel
2 3 6
5 4 3 2 1
1 4 5
1
Right channel output jack
2
Left channel output jack
3
4
Y/Pb/Pr output jack
Digital signal COAXIAL output jack
5
6
S-Video output jack
VIDEO output jack
4
5
9
10
11
12
6
7
8
1
2
3
4
13
14
15
16
17
18
19
20
21
Remote control
Some features of the player can only be performed by the remote control.
Some features described in this owner's manual are related to the Disc's encoding.
Some features may not be available, if the disc encoding does not support the feature.
22
23
24
25
29
30
31
32
33
34
35
36
37
38
39
40
26
27
28
15
16
17
18
19
9
10
11
12
6
7
8
4
5
1
2
3
13
14
20
INTRODUCTION
REMARK
Some features contained in this DVD player are related to theDVD Disc's software.
Some features cannot be performed if the disc does not support the feature, or requires special settings.
Check the features printed on the disc's packing or follow the instructions of the Disc's on screen menu.
31
32
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
30
40
Notes
The remote control transmits a directiona infrared beam. Be sure to aiml the remote control directly at the infrared sensor during operation. When the sensor is covered or there is a large object between the remote control and the sensor, the sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a f luorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting.
5
SYSTEM CONNECTION
Preparations
Accessories
1. Remote controller 2. Audio/Video cable 3. User's manual
(check whether be fully equipped after open the box)
Battery installation of remote controller
Place two AAA batteries into the battery compartment. Be sure the polarities are correct.
There should be no large obstacles between the remote controller and the main unit.
System connection(Optional according to your back panel)
1. When making connection between this unit and other components, be sure all connection with power-off.
2. Audio/Video cables are connected according to the different colour identification and they should be fitted firmly.
Yellow to video terminal
White to audio terminal L,
Red to audio terminal R,
3. Scheme of connection
2CHANNEL CONNECTION
Y/Pb/Pr OUTPUT
TO TV VIDEO OUTPUT
TO S-VIDEO OUTPUT
DIGITAL COAXIAL OUTPUT
76
GETTING STARTED
Unpack the unit.
Read through thisowner's manual before installation and use.
Load batteries into the remote control unit.
Connect the system,make sure the connections are secured.
Connect the power plug to the AC power outlet.
Play a disc
Switch on the player
Push the main power button to turn on the
DVD unit. Power on the TV set and the amplifier if connected.
Load a disc
REMARK
Some features contained in this DVD player are related to the DVD disc's software.
Some features cannot be performed if the disc does not support The feature, or requires special settings.
Check the features printed on the disc's packing or follow the instructions of the Disc's on screen menu.
Press EJECT button on the remote control (or front panel) to open the disc tray. Load a disc and press EJECT to close the disc tray
(Note, place the disc's label side up, blank side down)
.
EJECT
Automatic Play
The unit will take a few seconds to download the disc initial data, display the disc type logo in the left upper corner of the TV screen, and then start playing automatically .
If a DVD Disc Menu appears on screen
Press PLAY button on the remote
(or on the unit) to start playing.
or
Press CURSOR buttons to select the desired feature in the menu,
2
And then press the ENTER button to confirm a selection.
1 take longer time to download the initial data.
DVD disc that does not match the region code cannot be executed by this player.
77
Return to the disc main menu, press MENU button on the remote.
Prevent loading the disc upside down.
Screen saver
The player is equipped with an automatic screen saver, for the purpose of protecting the TV screen.
The TV screen will be black and a screen
Saver will appear on screen if :
No disc is loaded for 180 seconds
In STOP mode and no button has been
Pressed for 180 seconds.
(except in the player or disc menu)
When any button is pressed, the player will resume to normal active mode.
GETTING ST ARTED
... ... ...
... ... ...
8
FUNCTION BUTTONS
Power ON / OFF
POWER ON /OFF
To switch the player Between power on and off mode:
Press POWER button on front panel
(Always switch off the player after use)
Open /Close disctray
EJECT
To open and close The disc tray:
Press EJECT button on the remote
Play / Pause / Stop
3 1
2
To play the Disc
2 Then Press PAUSE button
to pause.
Press to resume normal playback.
3 Press STOP button to stop in two modes: a) Press Once STOP memorizes the interrupt position.
( May resume with Play button ) b) Press Twice To stop completely
(Will NOT resume with Play button)
9
FUNCTION BUTTONS
Skip Forward / Backward
2
1
1 Press to skip forward (chapters)
2 Press to skip backward (chapters)
Player will not advance or reverse during
"WARNING" section of any disc.
Forward / Backward
2
The unit mode
Slow Forward
3
1
Repeat pressing the button to change search speed
2 4 8 20
Repeat pressing the Button to change search speed
2 4 8 20
3 to resume normal playback
Player will not advance or reverse during
"WARNING" section of any Disc.
1 Press to play slow forward
Repeat pressing the Button to change slow forward speed
1
2 2 Press PLA Y button to resume normal playback
The unit muted in SLOW mode
10
Select an item in menu
4
1
2
3
FUNCTION BUTTONS
In the disc menu or setup menu to move between function items.
to confirm a selection.
to cancel an entry.
to return to the previous menu.
Disc TItle /Menu
2 users to select functions on screen.
1 return to the DVD disc Menu.
return to the DVD disc Title.
Some DVD discs refuse the "TITLE” function.
Clear
1
Setting program or searching need to input number. press
CLEAR
CLEAR button to clear the number when the input number is wrong.
11
FUNCTION BUTTONS
Numeric Key Pad / Direct Program access
1
1
Direct Program access
Input the desired Chapter or Track number using the
Numeric key pad. Press ENTER button to confirm your direct access Chapter or key selection.
Chapter - when Playing a DVD disc, or
Track - when playing a CD or Mp3 disc
NOTE
Program functionality depends on different DVD disc's format, some DVD discs do not allow direct access function.
Multi-Angle
1
A DVD disc may contain up to 9 selectable viewing angles.
If a DVD disc contains Multi-Angle feature, viewing angles may be selected:
1 During in playback, repeat pressing
ANGLE button to select the desired viewing angle
Status will be displayed on screen..
1/3
..... ....
..... ....
..... ....
..... ....
..... ....
..... ....
Total angles
Current angle
..... ....
..... ....
..... ....
..... ....
..... ....
..... ....
12
Multi-Subtitle
1
FUNCTION BUTTONS
If a DVD disc contains the Multi-Subtitle feature, subtitle may be selected:
1 During in playback, repeat pressing
SUBTITLE button to select the desired subtitle.
Status will be displayed on screen.
Total subtitle
... ... ...
... ... ...
.....
1 / 2 Eng
Current subtitle
... ... ...
... ... ...
NOTE
A DVD disc may contain up to 32 subtitle selections.
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
Multi-Audio Soundtrack
If a DVD disc contains Multi-Audio Soundtrack feature,
Audio Language can be selected:
button LANGUAGE to select the desired audio language.
Playback status will be displayed on screen.
Total Language
1
1 / 3 Eng 6 Ch
Current Language
NOTE
A DVD disc may contain up to 8 audio language selections.
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
on a DVD disc start up menu. ... ... ...
... ... ...
Press CURSOR Button to select and ENTER button to confirm.
13
V-Mode
1
FUNCTION BUTTONS
2
1 First,You should press[STOP] Key STOP
2 Press[V-MODE]key Video mode switch again.
In the condition of NORMAL mode.press [V-MODE] key may select S-video,YUV,RGB,YPbPr,VGA output.
To use this function, your TV Set must have progressive scan features.
Reset
1
2
1 First,You should press[STOP] Key STOP
2 press”RESET”button on the remote,this option will resume the original Settings of this machine.
RESET
14
FUNCTION BUTTONS
SEARCH a desired section
This functi on does NOT apply to M P 3
1
SEARCH
Press the to play at a desired Title, Chapter or Time.
1
DVD disc
SEARCH
Press the SEARCH
Press DOWN button highlight desired item.
TITLE ---
CHAPTER ---
TIME --:--:--
Input title number
Input chapter number
Input time hh:mm:ss
(Hour : Minute : Second)
Press ENTER button.
CD disc
SEARCH
Press the SEARCH button to T rack Search mode.
SEARCH
Press the SEARCH button again to Disc Search mode.
TIME --:--:-Input time hh:mm:ss
(Hour : Minute : Second)
TRACK --Input track number XXX
(Track Number)
Press ENTER button.
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
Search
Time
Title/Chapter
--:--:--
---/---
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
Search
Time
Track
--:--:--
---
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
... ... ...
NOTE
SEARCH functionality depends on different DVD disc's format. Some DVD discs do not allow SEARCH function.
SEARCH does NOT function during Program playback.
15
FUNCTION BUTTONS
Repeat
1 Press
REPEAT
REPEAT button multiple times to reach desired repeat mode (see below).
DVD disc
Repeat Chapter
Repeat Title
Repeat Off
Repeat the Chapter
Repeat the Title
Repeat function off
CD disc
Repeat Single
Repeat All
Repeat Off
Repeat the existing track
Repeat all tracks
Repeat function off
MP3 disc
Repeat Single
Repeat All
Repeat Off
Repeat the existing track
Repeat all tracks
Repeat function off
.........
Repeat Chapte r
1
NOTE
Repeat functionality depends on different disc's production format, some DVD discs do not allow repeat function.
20
Repeat the section A-B
1 To repeat playback of a desired section:
1) Press the
A-B
A-B button
at the beginning of the desired section, "A".
2) Press the
A-B
A-B button again
at the end of the desired section, "B".
1
Rep A - B
.........
.........
The player will repeat playback of the section from A to B.
Press the A-B
A-B
button again to cancel the function and return to normal play .
NOTE
A-B repeat depends on different disc's production format, some DVD discs do not allow repeat function.
A-B function does not apply to MP3 disc.
The period between A and B should be at least 3 seconds.
16
.........
.........
.........
.........
.........
.........
.........
FUNCTION BUTTONS
ZOOM
2
1 2
In DVD mode
1
ZOOM
Press the ZOOM Button to enlarge viewable picture.
Press the button repeatedly to change the zoom scale:
Q1 Q2 Q3 Q4
2 Press the CURSOR buttons to adjust the zooming position.
Enlarged scale
.........
.........
.........
.........
.........
.........
.........
.........
Q2
.........
.........
.........
.........
.........
NOTE
The picture quality is degraded as the picture is increased.
Mute
1
1
MUTE
MUTE button
To mute ( turn off ) the audio output.
Press the button again
To resume normal audio output.
17
Shuffle
FUNCTION BUTTONS
Under DVD Player in Automatic working status with Shuffle function on, it can play the following chapter automatically after finishing the current one.
Pressing next button is also available
In SHUFFLE off status, the automatic play function will not available.
Shuffle on
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
PBC Play
1
1 For VCD2.0 disc playing in the condition of PBC ON, Song
selection can only be done, when the playing returned to main
menu in the condition of PBC OFF, press relevant number Key
to get favorite song during playing
Channel
1
When play SVCD, VCD CD disc, press CHANNEL
Key to select left vocal, Right vocal , Stereo vocal
CHANNEL
1
18
FUNCTION BUTTONS
Program setting
Program to play a DVD, CD and MP3 disc in a desired sequence automatically .
Load a DVD disc.
DVD program menu
1
PROG
PROG button,
the DVD program menu will appear .
Program Input Title/Chapter
2 Use numeric key pad to input the Title number and the Chapter number,
1 __ __
2 __ __
3 __ __
4 __ __
5 __ __
6 __ __
Play Program
7 __ __
8 __ __
9 __ __
Clear All
10 __ __
11 __ __
12 __ __
3 Highlight "Play Program", to start the program.
Highlight "Clear All", to clear all input.
Press ENTER button to confirm.
4 Press
PROG
PROG button to exit the program menu.
PROG
5 Press PROG button to cancel the program.
CD program menu
Program Input
1 ___
2 ___
4 ___
5 ___
3 ___ 6 ___
Play Program
7 ___
8 ___
9 ___
Clear All
10 ___
11 ___
12 ___
Load a CD disc.
PROG
1 PROG button,
the CD program menu will appear .
2 Use numeric key pad to input the Track number
MP3 program menu
Program Input
1 ___
2 ___
3 ___
4 ___
5 ___
6 ___
Play Program
7 ___
8 ___
9 ___
Clear All
10 ___
11 ___
12 ___
NOTE
Some DVD discs do not allow programming.
Single track disc cannot be programmed.
3 Highlight "Play Program", to start the program.
Highlight "Clear All", to clear all input.
Press ENTER button to confirm.
4 Press
PROG
PROG button to exit the program menu.
PROG
5 Press PROG button to cancel the program.
Load a MP3 disc.
PROG
1 PROG button,
the MP3 program menu will appear .
2 Use numeric key pad to input the Track number
3 Highlight "Play Program", to start the program.
Highlight "Clear All", to clear all input.
Press ENTER button to confirm.
4
PROG
Press PROG button to exit the program menu.
PROG
5 Press PROG button to cancel the program.
19
Return
FUNCTION BUTTONS
1
RETURN
In PBC mode, when pressing “RETURN” Key to return to the menu, thus canceling the PBC mode , the “RETURN” key will be invalid
Mark
3
1
2
STORING MARKS MEMORY
1. Press the “MARK” button on remote control during the disc
is played and the menu of mark setting with three bookmarks
will appear on the screen.
2. Use the direction buttons ( or ) on the remote control to
select mark numbers (Bookmarks 1, 2 & 3), and press
ENTER button to enter the playing times where you would like
to view again afterwards. A maximum of three marks can be
stored.
3. Press “Clear” button to clear a particular mark. Press “MARK”
button to clear the display.
PLAYBACK FROM A MARKED POSITION
1. Press the “MARK” button on the remote control to display
the menu of mark setting on the screen.
2. Use the direction buttons ( or ) on the remote control to
select your desired mark, and press “ENTER” button to
start to playback from that point.
3. Marked positions can be recalled anytime by pressing
“MARK” button on the remote control.
Note:
All the marks are cleared when the power is off or the disc is removed.
20
ON SCREEN DISPLA Y
DISPLAY
Press DISPLAY button , an On Screen Display (OSD) indicator will be displayed at the upper part of the TV screen in displaying the disc information and operation status.
The OSD indicator will remain on screen until pressing the DISPLAY button to turn it off.
The OSD indicator is a user friendly interface designed for displaying the status of the playback.
When a dif ferent disc is loaded (DVD, CD or MP3), the OSD indicator bar will be different.
OSD - DVD mode
DVD 0012::33 01:36:25
Title 1/ 6 Chapter 3 / 21 Angle 1/1
Audio
Subtitle
Bitrate
1/3
....
1/2
AC-3
6.910 Mbpss
6 Ch
Disc type
... ... ...
Disc Title current title / total disc titles
Disc Subtitle current subtitle / total disc subtitles
Audio Sound Track current audio / total tracks
... ... ...
Chapter remain time
Multi-angle
Current angle / Total angles
Audio format
AC-3 6 Ch
Chapter current chapter / total chapters
DTS
LPCM LPCM
Playback time /
OSD - CD mode
... ... ...
... ... ...
CD
TRACK 2/3
00:12:33 01:36:25
... ... ...
... ... ...
Disc type
... ... ...
Disc TRACK
21
... ... ...
Playback time /
Disc remain time
ON SCREEN DISPLAY
MP3 mode
Playback time
Current folder Disc T rack current track / total tracks
.........
.........
Mp3 2/133
[Root]
.........
.........
.........
.........
3
4
1
2
5
001
002
003
004
005
8
9
6
7
10
006
007
008
009
010
File: 002
00:02:43
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
.........
Playing track highlight
Playing track file information
(Information provided by the disc)
Selection highlight
(Press ENTER
ENTER button to play this track)
Auto playback
The player will load the MP3 disc and auto start to playback from track one till the last track of the root directory.
Select a track
Press ARROW button to highlight the desired track, and switch between folder and pages.
Press ENTER button to play the selected track.
Playing track file information
You may add the information of the MP3 file while you create the disc, e.g. artist, song name and date etc., Those information of the playing track will be display at the lower part of the screen.
22
SETUP
Various features of the player can be adjusted in the SETUP menu:
Press SETUP button
SETUP menu appears.
Language Video Audio Rating
Video
Enter this menu to setup the video setting
Press SETUP button
Highlight "Video",
Language Video Audio Rating
TV shape 4:3LB 4:3PS
16:9
Highlight the desired icon Press ENTER
ENTER button to activate the setting sub menu.
Language
Enter this menu to setup the language in
OSD display, DVD disc subtitle, DVD disc audio and DVD disc start menu.
Press SETUP button
Highlight "Language",
Highlight the desired item and press ENTER button,
Highlight the desired item,
ENTER
Press ENTER button to confirm.
Press SETUP button to save the setting and quit.
Default setting
TV Shape 4:3 PS
Language Video Audio Rating
English OSD Menu
Subtitle
Audio
DVD Menu
English
Off
English
English
TV screen
The aspect ratio of the picture provided by the DVD player can be varied in line with the features available on the TV in use.
4:3 Letter Box
Allow you to see movies in their original aspect ratio.
Entire frame of the movie will be display on screen, but it will occupy a smaller portion of the screen.
Highlight the desired item and press ENTER button,
Highlight the desired item,
Press SETUP button to save the setting and quit.
Default setting
OSD Menu
Subtitle
Audio
DVD Menu
: English
: Off
: English
: English
23
4:3 Pan Scan
The signal will fill the screen with the centre of the picture. The left and right edge of picture may be cut outside range of the screen.
16:9 Wide Screen
When you connect to a wide screen TV , this setting will allow the original aspect ratio will be display full screen.
NOTE
Depending on the DVD disc format, e.g. 2.35:1, the wide screen setting may still having black margins above and below the picture.
Audio (digital audio)
Enter this menu to setup the digital audio output format of different signal type.
The selectable output formats are PCM or Raw .
Press SETUP Button
Highlight "Audio",
Press ENTER , Audio sub menu appears.
Language Video Audio Rating
Digital output PAW
PCM
OFF
Highlight the desired item and press ENTER button,
Highlight the desired
Press ENTER
Press SETUP
item,
button to save the setting and quit.
SETUP MENU (Press SETUP button)
Rating
Enter this menu to setup the rating level of the player.
The player will require a password to play any disc with rating level higher than the setting.
Press SETUP
button
Highlight "Rating",
Press ENTER
ENTER button, Rating sub menu appears.
Language Video Audio Rating
Password
Rating
Load Factory
- - - -
8. Adult
Reset
Highlight "Password" selection,
Press ENTER
input the 4 digits password,
Default setting
Pas sw ord
Rat ing
: 0000
: 8. Ad ult
Highlight "Rating",
Repeatedly pressing to change the setting:
ENTER button
1. Kid Safe
2. G
3. PG
4. PG_13
5. PG_R
6. R
7. NC_17
8. Adult
Highlight "Password" selection,
Press ENTER button to lock.
Press SETUP butto n to save the setting and quit.
24
TROUBLE SHOOTING
Should your DVD player develop a problem, please check below before requesting service:
Symptom
No Power
Does not play
No Picture
Picture noise / distorted
Picture not full screen
Malfunction
No sound
Check and Action
Check if the power cord has been properly connected to the power outlet.
Check if the main power has been switched on.
No disc, load a disc.
Disc has been loaded upside down. Place the disc with the label side up.
Disc's region code does not match to the player.
Disc is not correct type for player.
Disc is damaged or dirty, clean the disc or try another disc.
Moisture may be condensed inside the player. Remove the disc and leave the unit power on for one or two hours.
Check if the TV set has power on, use TV remote to select A/V signal for
DVD rather than broadcast.
Check if the system connection is proper and secure.
Check if the connection cables are damaged.
Clean the disc.
The disc is dirty or damaged. Clean the disc or try another disc.
Reset the color system of the player or the TV set.
Try to direct the player to the TV set instead of via other components, such as a VCR.
Select the screen format from the player's SETUP MENU, see " SETUP MENU " of t his manual.
Select the screen format from DVD disc menu.
Should the player develop a malfunction, unplug the player for
30 minutes. After 30 minutes, power on the player and the restore function should reset the player.
LANGUAGE
DTS disc used. Press the remote control “ LANGUAGE " button re-select the audio setting on the remote.
25
CAUTION
RISKOF ELECTRIC SHOCK
DO NOT OPEN
Symptom
Cannot SKIP or SEARCH
No sound or sound output not complete
No surround sound
MP3 disc no sound or noisy
Remote control does not function
TROUBLE SHOOTING
CAUTION
: To reduce the risk of fire and electric shock, do not remove the cover (or back) of the unit. Refer servicing only to Singer Service Technician
Check and Action
Some discs are programmed that do not allow users to SKIP or SEARCH at some sections, especially at the beginning WARNING section.
Single Chapter disc cannot apply SKI P function.
Check if the TV and Amplifier have been switched on, and correctly set.
Check if the TV and Amplifier system connection is secured.
Press LANGUAGE button to select other audio tracks output of disc.
Check if the MUTE function of the TV or Amplifier has been activated.
There will be no sound output during P AUSE / STEP / SLOW and SEARCH.
If digital output has been applied:
Press SETUP button
Highlight "AUDIO"
Highlight "Digital Out"
Select RAW or PCM
Press SETUP button
Power on the amplifier or active type loudspeakers.
When PC program files or other data files are mixed with
MP3 files in the same disc, the player may play the non-MP3 files with noise or no sound.
Check the disc, if all the files on disc are MP3 files
Skip the f ile, try other files.
Remove the obst acles between the remote control and the player .
Point the remote control towards the remote sensor on the player.
Check if the batteries of the remote control have been loaded with correct polarities.
Replace the batteries of the remote control.
26
SPECIFICATIONS
Type of Disc
Video Format
Audio Format
Signal Output
Frequency Response
S/N radio
THD
Output Terminals
DVD
CD-DA
CD-MP3
Kodak Picture CD
CD-R / CD-RW
MPEG 2
MPEG 1, LAYER 1, LAYER 2 , LAYER 3
Color System:
Audio System:
NTSC
DIGITAL down mix stereo
DIGITAL digital output
Audio DAC 16bit/48KHz
Video Output: 1 Vpp (at 75 ohm)
Audio Output (Stereo): 2 Vpp
CD:
DVD:
4Hz 20KHz (EIAT)
4Hz 22KHz (48K)
4Hz 44KHz (96K)
> 92 dB
< 0.04%
Video (composite) output X1
S-Video outpu X 1t
YPbPr output X1
Power input
Dimensions
AC 90-240V 50/60Hz 25W
Body size : W430 x D280 x H48 mm
Packing size : W510 x D335x H90 mm
Net weight : 3 Kg
27
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 ESSENTIAL SETUP
- 7 About DVD
- 8 About the player
- 8 Remote control
- 10 SYSTEM CONNECTION
- 11 Play a disc
- 12 Screen saver
- 18 [ V-Mode ] , [ Reset ] , [ Search a desired section ]
- 23 [ Program ] , [ Return ] , [ Mark ]
- 25 OSD DVD mode
- 25 OSD CD mode
- 26 OSD Mp3 mode
- 27 LANGUAGE MENU
- 28 VIDEO MENU
- 28 AUDIO MENU
- 28 RATING MENU
- 29 TROUBLE SHOOTING
- 31 SPECIFICATIONS