DMP-CD100
MP3 CD Player
User’s Manual
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures
Warnung!
Dies ist in Produkt der Klasse B. Im Wohnbereich kann dieses Produkt
Funkstoerungen verursachen. In diesem Fall kann vom Benutzer verlangt werden,
angemessene Massnahmen zu ergreifen.
Advertencia de Marca de la CE
Este es un producto de Clase B. En un entorno doméstico, puede causar interferencias
de radio, en cuyo case, puede requerirse al usuario para que adopte las medidas
adecuadas.
Attention!
Ceci est un produit de classe B. Dans un environnement domestique, ce produit
pourrait causer des interférences radio, auquel cas l`utilisateur devrait prendre les
mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe B. Se utilizzato in ambiente domestico il
prodotto può causare interferenze radio, nel cui caso è possibile che l`utente debba
assumere provvedimenti adeguati.
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesirable operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio TV technician for help.
SAFETY CERTIFICATION
This compact disc player is made and tested to meet safety standards of the FCC,
requirements and compliance with safety performance of the U.S. Department of
Health and Human Services, and also with FDA Radiation Performance Standards 21
CFR Subchapter J.
SAFETY PRECAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not take the DMP-CD100 apart. The laser beam used in the DMP-CD100
could harm your eyes.
Do not insert pins, etc., inside the DMP-CD100. This unit is equipped with a
safety device which automatically turns the laser beam off when the disc
compartment is opened. If a pin or other metal object should get inside the
DMP-CD100, however, this safety device may be deactivated.
The DMP-CD100 should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
Power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, pay particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the
DMP-CD100.
Never remove the enclosure. If the internal parts are touched accidentally, a
serious electric shock might occur.
If an abnormal smell or smoke is detected, immediately turn the power OFF and
pull out the power cord. Contact your dealer or nearest service center.
Avoid placing the DMP-CD100 under direct sunlight or near a source of heat
such as heating equipment. Particularly, never leave it in an automobile or on the
dashboard.
The DMP-CD100 may not function properly if used at extremely low, or
freezing temperatures. The ideal ambient temperature is above +5°C (41°F).
Avoid places where it is dusty or where the humidity is high.
Avoid placing the DMP-CD100 on an unstable surface such as a shelf or in a
place subject to vibrations.
Keep the DMP-CD100 away from sources of magnetic fields such as TV sets,
speaker systems, radios, motorized toys or magnetized object.
Do not use volatile solvents such as alcohol, paint thinner, gasoline, or benzene,
etc. To clean the cabinet, use a clean dry cloth.
The user should not attempt to service the DMP-CD100 beyond that described in
the operating instructions. All other servicing should be referred to qualified
service personnel.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
LIMITED WARRANTY
D-Link Systems, Inc. (“D-Link”) provides this limited warranty for its product only to the person
or entity who originally purchased the product from D-Link or its authorized reseller or
distributor.
Limited Hardware Warranty: D-Link warrants that the hardware portion of the
D-Link products described below (“Hardware”) will be free from material defects in
workmanship and materials from the date of original retail purchase of the Hardware, for the
period set forth below applicable to the product type (“Warranty Period”) if the Hardware is used
and serviced in accordance with applicable documentation; provided that a completed
Registration Card is returned to an Authorized D-Link Service Office within ninety (90) days
after the date of original retail purchase of the Hardware. If a completed Registration Card is
not received by an authorized D-Link Service Office within such ninety (90) period, then the
Warranty Period shall be ninety (90) days from the date of purchase.
Product Type
Product (excluding power supplies and fans), if
purchased and delivered in the fifty (50) United States,
or the District of Columbia (“USA”)
Warranty Period
As long as the original
purchaser still owns the
product
Product purchased or delivered outside the USA
One (1) Year
Power Supplies and Fans
Spare parts and spare kits
One (1) Year
Ninety (90) days
D-Link’s sole obligation shall be to repair or replace the defective Hardware at no charge to the
original owner. Such repair or replacement will be rendered by D-Link at an Authorized
D-Link Service Office. The replacement Hardware need not be new or of an identical make,
model or part; D-Link may in its discretion may replace the defective Hardware (or any part
thereof) with any reconditioned product that D-Link reasonably determines is substantially
equivalent (or superior) in all material respects to the defective Hardwa re. The Warranty
Period shall extend for an additional ninety (90) days after any repaired or replaced Hardware is
delivered. If a material defect is incapable of correction, or if D-Link determines in its sole
discretion that it is not practical to repair or replace the defective Hardware, the price paid by the
original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link
of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for
which the purchase price is refunded, shall become the property of D-Link upon replacement or
refund.
Limited Software Warranty: D-Link warrants that the software portion of the product
(“Software”) will substantially conform to D-Link’s then current functional specifications for the
Software, as set forth in the applicable documentation, from the date of original delivery of the
Software for a period of ninety (90) days (“Warranty Period”), if the Software is properly
installed on approved hardware and operated as contemplated in its documentation. D-Link
further warrants that, during the Warranty Period, the magnetic media on which D-Link delivers
the Software will be free of physical defects. D-Link’s sole obligation shall be to replace the
non-conforming Software (or defective media) with software that substantially conforms to
D-Link’s functional specifications for the Software. Except as otherwise agreed by D-Link in
writing, the replacement Software is provided only to the original licensee, and is subject to the
terms and conditions of the license granted by D-Link for the Software. The Warranty Period
shall extend for an additional ninety (90) days after any replacement Software is delivered. If a
material non-conformance is incapable of correction, or if D-Link determines in its sole
discretion that it is not practical to replace the non-conforming Software, the price paid by the
original licensee for the non-conforming Software will be refunded by D-Link; provided that the
non-conforming Software (and all copies thereof) is first returned to D-Link. The license
granted respecting any Software for which a refund is given automatically terminates.
What You Must Do For Warranty Service:
Registration Card. The Registration Card provided at the back of this manual must be
completed and returned to an Authorized D-Link Service Office for each D-Link product within
ninety (90) days after the product is purchased and/or licensed. The addresses/telephone/fax
list of the nearest Authorized D-Link Service Office is provided in the back of this manual.
FAILURE TO PROPERLY COMPLETE AND TIMELY RETURN THE REGISTRATION
CARD MAY AFFECT THE WARRANTY FOR THIS PRODUCT.
Submitting A Claim. Any claim under this limited warranty must be submitted in writing
before the end of the Warranty Period to an Authorized D-Link Service Office. The claim must
include a written description of the Hardware defect or Software nonconformance in sufficient
detail to allow D-Link to confirm the same. The original product owner must obtain a Return
Material Authorization (RMA) number from the Authorized D-Link Service Office and, if
requested, provide written proof of purchase of the product (such as a copy of the dated purchase
invoice for the product) before the warranty service is provided. After an RMA number is
issued, the defective product must be packaged securely in the original or other suitable shipping
package to ensure that it will not be damaged in transit, and the RMA number must be
prominently marked on the outside of the package. The packaged product shall be insured and
shipped to D-Link, 53 Discovery Drive, Irvine CA 92618, with all shipping costs prepaid.
D-Link may reject or return any product that is not packaged and shipped in strict compliance
with the foregoing requirements, or for which an RMA number is not visible from the outside of
the package. The product owner agrees to pay D-Link’s reasonable handling and return
shipping charges for any product that is not packaged and shipped in accordance with the
foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
What Is Not Covered:
This limited warranty provided by D-Link does not cover:
Products that have been subjected to abuse, accident, alteration, modification, tampering,
negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that
is not contemplated in the documentation for the product, or if the model or serial number has
been altered, tampered with, defaced or removed;
Initial in stallation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal
maintenance;
Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic
damage; and
Any hardware, software, firmware or other products or services provided by anyone other than
D-Link.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED
HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY
KIND INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN
ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED
WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY
COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE
RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS
WITH THE PURCHASER OF THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS
NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER
LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT,
INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES
FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR
MALFUNCTION, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON,
OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY
SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO
WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED
WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED
WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR
NON-CONFORMING PRODUCT.
GOVERNING LAW: This Limited Warranty shall be governed by the laws of the state of
California.
Some states do not allow exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may
not apply. This limited warranty provides specific legal rights and the product owner may also have
other rights which vary from state to stat e.
Trademarks
Copyright 1999 D-Link Corporation. Contents subject to change without prior notice.
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other
trademarks belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without
permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the United
States Copyright Act of 1976.
TABLE OF CONTENTS
MP3 FILE INFORMATION ................................................... 1
POWER SUPPLY ................................................................... 2
FEATURE LAYOUT .............................................................. 4
LCD DISPLAY INDICATORS ............................................... 5
PLAYING A CD..................................................................... 5
BASIC FEATURES ................................................................ 6
REPEAT FEATURES ............................................................. 7
ADVANCED PLAYING MODES .......................................... 8
REMOVING THE DISC ...................................................... 10
HANDLING COMPACT DISCS ......................................... 10
CLEANING DISCS .............................................................. 11
TROUBLESHOOTING GUIDE........................................... 12
SPECIFICATIONS................................................................ 13
MP3 FILE INFORMATION
WHAT IS MP3?
MP3 is the abbreviation of “MPEG 1 Audio Layer 3”. MPEG Audio is a
compression specification that compresses the audio portion only. This audio
compression method is used in DVD and Video CD, etc. The audio data has
been compressed into about 1/10 the size of a normal audio file.
SEQUENCE OF PLAYING MP3 FILES
MP3 files will be played in the sequence that the writing software had
recorded. Therefore, it may be different between the sequence that you want
to record and the sequence of playing. To ensure that the songs play in the
order that you want, input “01” ~ “99” before the file names in the desired
sequence and then record onto a CD-R. Refer to your CD recording software
for options on organizing MP3 files.
IMPORTANT NOTES
D-Link is not responsible for playability of MP3 in any case due to recording
condition such as PC performance, writing software, media ability or etc.
ACCEPTABLE MEDIUM
• CD-DA Audio CD
• CD-R : ISO-9660 or Joliet file structure.
• Maximum number of recognizable directories : 255
SETTINGS FOR YOUR MP3 ENCODER AND CD WRITER
• When you use your MP3 encoder to compress audio data to an MP3 file,
set the transfer bit rate of the encoder to fixed 128 kbps (Constant Bit
Rate).
• Sampling frequency is 44.1 kHz.
• When burning your MP3 CD’s, check “Disc at Once”.
WRITING FILES ONTO A CD
When a CD containing MP3 data is loaded, the DMP-CD100 checks all the
files on the CD. If the CD contains a lot of folders or non-MP3 files, it will
take time for the DMP-CD100 to start playing MP3 files. In addition, it may
also take time for the DMP-CD100 to move to the next MP3 file. A file
1
search or folder search may not be performed smoothly. You should not write
non-MP3 files or unneeded folders along with MP3 files on the CD.
POWER SUPPLY
RECHARGEABLE NICKEL CADMIUM BATTERY
INSTALLATION
1. Remove the battery compartment
cover by sliding the cover away from
the DMP-CD100.
2. Insert the rechargeable
nickel-cadmium battery into the
battery compartment. Be sure to
observe the proper polarity (The +
and - signs, as indicated inside the
battery compartment).
NOTE: Fully charge the
rechargeable nickel - cadmium
battery before using it for the first
time.
3. Close the battery compartment.
4. Plug one end of the supplied AC adaptor into the DC jack.
Then plug the other end into an AC wall outlet.
5. When charging is completed, disconnect the AC adaptor plugs from both
the DMP-CD100 and the AC outlet.
NOTE:
• The battery takes approximately 10-15 hours after the AC adaptor is
connected to be fully charged.
• The indicator on the right side of the DMP-CD100 will light on during
charging.
• Use the DMP-CD100 with the supplied AC adaptor. Using with other
AC adaptors could damage the DMP-CD100.
• The DMP-CD100 can be powered up by using the AC adaptor alone
without batteries.
NICKEL-CADMIUM (NICAD) BATTERIES
2
The DMP-CD100 is equipped with battery recharging circuitry. For safety
measures, it requires specifically made NICAD (Nickel-Cadmium) batteries.
Use ONLY the following rechargeable battery types: KENWOOD NB-77 /
NB-88, PANASONIC RP-BP60D, SONY NH-DM2AA or equivalent.
NOTE: It is always a good idea to let Nickel-Cadmium batteries run all the
way down before charging them. When you do charge them, do so to their
full potential and they will last longer and provide more power.
ALKALINE BATTERY INSTALLATION
Insert two AA batteries into the battery compartment on the bottom of the
DMP-CD100. Be sure to observe the proper polarity (The “+” and “-“ signs,
as indicated inside the battery compartment).
NOTE:
• When replacing the alkaline batteries, use two new batteries of the same
type.
• When inserting the batteries, mistakenly inserting even one with
improper polarity will cause leakage.
BATTERY REPLACEMENT
If the rechargeable nickel-cadmium battery or the alkaline batteries are below
2.1v, the battery- low indicator will be shown on the display.
Recharge the rechargeable nickel-cadmium battery or replace the alkaline
batteries before using the DMP-CD100.
3
FEATURE LAYOUT
1. Disc Compartment Door
2. Electronic Shock Protection
Button (ESP)
3. Stop Button
4. Program Button
5. Reverse skip/Search Button
6. Display Window
7. Play/Pause Button
8. Mode/ Repeat Button
9. Forward skip/Search Button
10. Track Digit Button (T.Digit)
11. DBBS switch
12. Door Open Switch
13. Hold switch
14. Volume knob
15. Line Out Jack
16. Headphone Jack
17. Power Indicator
(Charging Indicator)
18. Batteries Compartment
19. AC-DC adaptor Input Jack
4
LCD DISPLAY INDICATORS
PLAYING A CD
1. Connect the headphones to the headphone
jack.
2. Set the volume knob to minimum.
3. Slide the door open switch to open the Disc
compartment door.
4. Insert a disc (CD or CD-R) with the label
side facing up.
5. Push down on the center of the front edge of
the door to close securely.
6. Slide the hold switch to the “OFF”
position.
7. Press the Play/Pause button. The
total number of tracks and total playing
time will be shown on the LCD display.
The DMP-CD100 will then start
playing track 1 of the disc
automatically.
8. Adjust the volume knob to a
comfortable level.
9. During playback mode, the track
number and elapsed playing time are displayed.
SKIP DURING PLAY MODE
5
1. Press the forward skip/search button once to skip to the beginning of the
next track.
2. Press the forward skip/search button repeatedly to skip ahead to the
beginning of other tracks.
3. Press the reverse skip/search button once to skip to the beginning of the
current track.
4. Press the reverse skip/search button twice or more quickly to go back to
previous tracks.
SEARCH DURING PLAY MODE
1. Press and hold the skip/search button to quickly advance or reverse
through the music at high speed.
2. Release the skip/search buttons to return to normal play.
BASIC FEATURES
PAUSE BUTTON
1. Press the play/pause button to pause playback temporarily.
2. The elapsed time will flash when paused.
3. Press it again to resume play.
STOP BUTTON
1. Press the stop button to stop playing the disc. The total number of tracks
will be shown on the display.
2. Press the Stop button to turn off the DMP-CD100.
HOLD SWITCH
1. Once all adjustments/selections
are completed, the hold switch may
be set to the (ON) position, and the
(HOLD) indicator appear on display, thereby deactivating all button
functions and eliminating the possibility of accidental unwanted selection.
2. Set to (OFF) position to resume normal operation.
DBBS SWITCH
1. This switch enhances the low frequency (BASS)
response.
6
2. Set the volume knob to a low listening level before activating the DBBS
switch, then adjust to your preference.
Note: The DBBS uses more battery power, thus drawing battery life more
quickly. Switch the DBBS to the Off position to conserve battery power.
REPEAT FEATURES
REPEAT ONE PLAY
1. Press the REPEAT/MODE Button until the
(REPEAT 1) Indicator appear on the display.
2. Select the desired track by pressing the
FORWARD OR REVERSE SKIP / SEARCH
Button.
3. The selected track will then begin playing
through to its end at which point it will
automatically return to the beginning of that track.
REPEAT ALL PLAY
1. Press the REPEAT/MODE Button until the
(REPEAT ALL) Indicator appear on the display.
2. The disc will then begin playing through to the
end of the last track, at which point it will
automatically return to the beginning of the first
track.
ELECTRONIC-SHOCK PROTECTION (ESP)
1. Press the ELECTRONIC SHOCK
PROTECTION button (ESP) to activate
the shock protection control function
during “Audio CD” play only.
2. The DMP-CD100 will store the CD’s
digital data in memory and then play back
from the memory.
3. If vibration occurs on the disc, the
DMP-CD100 will continue the playback
for 10 seconds until the display has shown
7
running out of lines in the tank.
4. In case of excessive vibration, the memory data may be exhausted and the
Electronic Shock Protection (ESP) may become temporarily ineffective.
NOTE: The battery power consumes more quickly when the Electronic Shock
Protection control is used. It is therefore recommended to set the ESP control
off when the DMP-CD100 is used in a place free of vibration.
ADVANCED PLAYING MODES
INTRO PLAY (INTRO)
1. Press the STOP button until the total track
number and total plays time appears on the
display.
2. Press the REPEAT/MODE button until the
Intro Indicator (INTRO) flash on the display.
3. Press the PLAY / PAUSE button to start
playing the Intro mode.
4. The disc will then begin playing the first ten
seconds of all tracks once and then stops
automatically.
PROGRAM PLAY (PGM)
1. Press the PROGRAM button until you see the
Program Indicator (PGM) flashing on the display.
2. Press the FORWARD OR REVERSE SKIP /
SEARCH button to select the desired track
number.
3. Press the PROGRAM button to store the track
number into that memory location. The next
memory location will flash on the display.
4. Repeat Steps 2 and 3 to store up to 22 tracks.
5. Press the PLAY / PAUSE button to start the
program play.
6. When the last programmed track has finished
playing, the DMP-CD100 will stop
automatically.
TO VIEW THE PROGRAMMED CONTENTS
8
1. Press the STOP Button once to stop the program play.
2. Press the PROGRAM Button repeatedly to display programmed tracks one
by one in the programmed order.
TO CLEAR THE PROGRAMMED CONTENTS
1. Press the STOP button twice or open the compartment door to clear the
program.
RANDOM PLAY (RDM)
1. Press the STOP button until the total track
number and total playtime appear on the display.
2. Press the REPEAT/MODE button until you see
the Random Indicator (RDM) flash on the
display.
3. Press the PLAY / PAUSE button to start the
Random play.
4. The DMP-CD100 will play tracks in a random
sequence selected from all tracks on the disc.
5. When all disc tracks have been played, the
DMP-CD100 will stop automatically.
MP3 DISC - TRACK DIGIT SELECTION PLAY (T.DIGIT)
1. By pressing the T. DIGIT Button (Track Digit), you can select high
numbered tracks quickly. Press the T-DIGIT once, twice, and thirdly, and
the digit representing hundredth, tenth and first number position will flash
respectively.
2. Press the FORWARD OR REVERSE SKIP/SEARCH Buttons to select
your digits according to its flashing digit position.
3. Press PLAY/PAUSE Button to play your desired track after repeating the
above selection procedures.
9
Notes: This function is not compatible with normal CD.
REMOVING THE DISC
1. After pressing the STOP button, wait for the disc to
stop rotating before sliding the DOOR OPEN switch
to remove the disc.
2. Hold the disc by the edge while slightly pressing on
the center spindle, then lift from the edge to release
and remove the disc.
HANDLING COMPACT DISCS
The DMP-CD100 is designed to
play CD/CD-R bearing the correct
identification logos. Other discs
may not conform to the CD/CD-R
standard and may not play properly.
Dirty, scratched or warped discs
may cause skipping or noise.
Handle the disc only by the edges.
To keep clean, do not touch its
surface. Discs should be stored in
10
their cases after use to avoid serious scratches. Do not expose discs to direct
sunlight, high humidity, high temperatures, or dust etc. Prolonged exposure
to extreme temperatures can warp the disc. Do not stick or write anything on
either side of the disc. Sharp writing instruments, or the inks used in some
felt-tip pens, may damage its surface.
CLEANING DISCS
Fingerprints should be carefully wiped from the surface
of the disc with a soft cloth. Unlike unconventional
records, compact discs have no grooves to collect dust
and microscopic debris, so gently wiping them with a
soft cloth should remove most particles. Wipe in a
straight motion from the center to the edge. Never use
thinner, benzene, record cleaner or anti-static spray on
a compact disc. Such chemicals can damage its plastic
surface.
11
TROUBLESHOOTING GUIDE
Check the following guide for problem resolution.
SYMPTOM
CD Player will not
turn on
Disc will not play
No sound from
headphones
Sound is skipping
CAUSE
Hold Switch position is
“ON”.
Dead or weak batteries.
AC adaptor not
connected properly.
Disc inserted incorrectly.
Defective compact disc.
CD compartment not
closed.
Moisture has formed
inside the CD deck.
Headphone plug not
inserted properly.
Volume control set to
minimum.
Weak batteries.
Defective compact disc.
The compact disc or
pickup lens is dirty.
Strong vibrations.
12
SOLUTION
Turn the Hold Switch to the
“OFF” position.
Replace batteries.
Check AC adaptor
connection.
Reinsert disc with label side
facing up.
Try another compact disc.
Close lid securely.
Take out the CD and leave
the CD compartment door
open for about an hour to dry
moisture condensation.
Reinsert headphone cord into
Headphone jack.
Increase the volume.
Replace with fresh batteries
or use AC power.
Try another compact disc.
Clean or replace the compact
disc or clean the pickup lens.
Place the CD player on a
level surface that is stable (no
vibrations).
SPECIFICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
1 Bit D/A Converter.
Digital Filter 8 Times Over-sampling.
Auto CD/MP-3 Detectable (reads CD/CD-R).
3 Spot Optical Pick-up.
Up to 22 Selected Music St oring Ability.
Up to 255 Music Selection of MP-3 Mode.
Fast Track Selector in MP-3 Mode.
Continue/ Intro/ Single Music/ Program/ Random Play Mode.
Repeat Function.
Bass Boost.
Audio Line Out.
Rechargeable Battery Function.
Power Source :
AC Adapter : Input 4.5V - 8V or Battery : DC 3V (AA1.5V x 2).
Headphone Output Power :
15mW (TYP).
Size of Unit :
136mm x 155mm x 29.5mm (W x D x H).
Net Weight of Unit :
200g.
**THE SPECIFICATION IS SUBJECT TO CHANGE WITHOUT PRIOR NOTICE**
13
Offices
AUSTRALIA
CANADA
CHILE
CHINA
DENMARK
EGYPT
FRANCE
GERMANY
INDIA
ITALY
JAPAN
RUSSIA
SINGAPORE
S. AFRICA
SWEDEN
TAIWAN
U.K.
U.S.A.
D-LINK AUSTRALASIA
Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia
TEL: 61-2-9417-7100 FAX: 61-2-9417-1077
TOLL FREE: 1800-177-100 (Australia), 0800-900900 (New Zealand)
URL: www.dlink.com.au E-MAIL: support@dlink.com.au, info@dlink.com.au
D-LINK CANADA
2180 Winston Park Drive, Oakville, Ontario L6H 5W1 Canada
TEL: 1-905-829-5033 FAX: 1-905-829-5095 BBS: 1-965-279-8732 FREE CALL: 1-800-354-6522
URL: www.dlink.ca
E-MAIL: techsup@dlink.ca
D-LINK SOUTH AMERICA
Isidora Goyenechea #2934 of.702, Las Condes, Santiago, Chile
TEL:56-2-232-3185 FAX: 56-2-2320923 URL: www.dlink.cl
E-MAIL: ccasassu@dlink.cl, tsilva@dlink.cl
D-LINK CHINA
2F., Sigma Building, 49 Zhichun Road, Haidian District, 100080 Beijing, China
TEL: 86-10-88097777 FAX: 86-10-88096789
URL: www.dlink.com.cn
D-LINK DENMARK
Naverland 2, DK-2600 Glostrup, Copenhagen, Denmark
TEL:45-43-969040 FAX:45-43-424347 URL: www.dlink.dk
E-MAIL: info@dlink.dk
D-LINK MIDDLE EAST
7 Assem Ebn Sabet Street, Heliopolis Cairo, Egypt
TEL: 202-2456176 FAX: 202-2456192 URL: www.dlink-me.com
E-MAIL: support@dlink-me.com, fateen@dlink-me.com
D-LINK FRANCE
Le Florilege #2, Allee de la Fresnerie
78330 Fontenay Le Fleury France
TEL: 33-1-30238688 FAX: 33-1-3023-8689 URL: www.dlink-france.fr
E-MAIL: info@dlink-france.fr
D-LINK GERMANY
Schwalbacher Stra_e74, 65760 Eschborn, Germany
TEL: 49-6196-77990 FAX: 49-6196-7799300
URL: www.dlink.de BBS: 49-(0)6192-971199 (Analog) 49-(0)6192-971198 (ISDN)
INFO LINE: 00800-7250-0000 (toll free) HELP LINE: 00800-7250-4000 (toll free)
REPAIR LINE: 00800-7250-8 0 0 0 E-MAIL: mbischoff@dlink.de, mboerner@dlink.de
D-LINK INDIA
Plot No.5, Kurla -Bandra Complex Road,
Off Cst Road, Santacruz (E), Bombay - 400 098 India
TEL: 91-22-652-6696 FAX: 91-22-652-8914 URL: www.dlink-india.com
E-MAIL: service@dlink.india.com
D-LINK ITALIA
Via Nino Bonnet No. 6/b, 20154 Milano, Italy
TEL: 39-02-2900-0676 FAX: 39-02-2900-1723
URL: www.dlink.it
E-MAIL: info@dlink.it
D-LINK JAPAN
10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan
TEL: 81-3-5434-9678 FAX: 81-3-5434-9868 URL: www.d-link.co.jp
E-MAIL: kida@d-link.co.jp
D-LINK RUSSIA
Michurinski Prospekt 49, 117607 Moscow, Russia
TEL: 7-095-737-3389, 7-095-737-3492 FAX: 7-095-737-3390
E-MAIL: vl@dlink.ru
D-LINK INTERNATIONAL
1 International Business Park, #03-12 The Synergy, Singapore 609917
TEL: 65-774-6233 FAX: 65-774-6322
URL: www.dlink-intl.com E-MAIL: info@dlink.com.sg
D-LINK SOUTH AFRICA
Unit 2, Parkside 86 Oak Avenue
Highveld Technopark Centurion, Gauteng, Republic of South Africa
TEL: 27(0)126652165 FAX: 27(0)126652186 CELL NO: 0826010806 (Bertus Moller)
CELL NO: 0826060013 (Attie Pienaar) E-MAIL: bertus@d-link.co.za, attie@d-link.co.za
D-LINK SWEDEN
P.O. Box 15036, S-167 15 Bromma Sweden
TEL: 46-(0)8564-61900 FAX: 46-(0)8564-6 1 9 0 1 E-MAIL: info@dlink.se
URL: www.dlink.se
D-LINK TAIWAN
2F, No. 119 Pao-Chung Road, Hsin-Tien, Taipei, Taiwan, R.O.C.
TEL: 886-2-2910-2626 FAX: 886-2-2910-1515 URL: www.dlinktw.com.tw
E-MAIL: dssqa@tsc.dlinktw.com.tw
D-LINK EUROPE
4 th Floor, Merit House, Edgware Road, Colindale, London, NW9 5AB, U.K.
TEL: 44-20-8731-5555 FAX: 44-20-8731-5511
URL: www.dlink.co.uk E-MAIL: info@dlink.co.uk
D-LINK U.S.A.
53 Discovery Drive, Irvine, CA 92618 USA
TEL: 1-949-788-0805 FAX: 1-949-753-7033 INFO LINE: 1-800-326-1688
BBS: 1-949-455-1779, 1-949-455-9616
URL: www.dlink.com E-MAIL: tech@dlink.com, support@dlink.com
Tech Support Hours: 6 A.M. to 6 P.M. Pacific Standard Time. Monday through Friday
REGISTRATION CARD
Print, type or use block letters.
Your name: Mr./Ms
_____________________________________________________________________________
Organization: ________________________________________________
Dept. ____________________________
Your title at organization:
________________________________________________________________________
Telephone:
_______________________________________ Fax:________________________________________
Organization's full address:
______________________________________________________________________
____________________________________________________________________________________________
Country:
_____________________________________________________________________________________
Date of purchase (Month/Day/Year):
_______________________________________________________________
Product Model
Product Serial No.
* Product installed in type of
computer (e.g., Compaq 486)
* Product installed in
computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name:
______________________________________________________________________________
Telephone:
_______________________________________ Fax:________________________________________
Reseller's full address:
_________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
oHome oOffice oTravel oCompany Business oHome Business oPersonal Use
2. How many employees work at installation site?
o1 employee o2-9 o10-49 o50-99 o100-499 o500-999 o1000 or more
3. What network protocol(s) does your organization use ?
oXNS/IPX oTCP/IP oDECnet oOthers_____________________________
4. What network operating system(s) does your organization use ?
oD-Link LANsmart oNovell NetWare oNetWare Lite oSCO Unix/Xenix oPC NFS o3Com 3+Open
oBanyan Vines oDECnet Pathwork oWindows NT oWindows NTAS oWindows '95
oOthers__________________________________________
5. What network management program does your organization use ?
oD-View oHP OpenView/Windows oHP OpenView/Unix oSunNet Manager oNovell NMS
oNetView 6000 oOthers________________________________________
6. What network medium/media does your organization use ?
oFiber-optics oThick coax Ethernet oThin coax Ethernet o10BASE-T UTP/STP
o100BASE-TX o100BASE-T4 o100VGAnyLAN oOthers_________________
7. What applications are used on your network?
oDesktop publishing oSpreadsheet oWord processing oCAD/CAM
oDatabase management oAccounting oOthers_____________________
8. What category best describes your company?
oAerospace oEngineering oEducation oFinance oHospital oLegal oInsurance/Real Estate oManufacturing
oRetail/Chainstore/Wholesale oGovernment oTransportation/Utilities/Communication oVAR
oSystem house/company oOther________________________________
9. Would you recommend your D-Link product to a friend?
oYes oNo oDon't know yet
10.Your comments on this product?
__________________________________________________________________________________________
__________________________________________________________________________________________