DPH-140S SIP Phone
Quick User Guide
Version 1.0
TABLE OF CONTENTS
1.0
INTRODUCTION............................................................................................................. 1
2.0
PACKAGE CONTENT.................................................................................................... 1
3.0
LIST OF FIGURES .......................................................................................................... 2
4.0
SUMMARY OF KEY FUNCTIONS .............................................................................. 3
5.0
CONNECTING THE IP PHONE ................................................................................... 4
6.0
IP PHONE SETUP ........................................................................................................... 5
6.1
MENU SUMMARY ............................................................................................................. 5
DISPLAY NAME ................................................................................................................ 7
6.2
6.3
ADSL DIALUP ................................................................................................................. 7
6.4
DHCP (DYNAMIC HOST CONFIGURATION PROTOCOL).................................................... 8
6.5
DNS SERVER IP............................................................................................................. 10
6.6
SNTP SERVER IP ........................................................................................................... 10
6.7
DO NOT DISTURB .......................................................................................................... 11
6.8
CF (CALL FORWARD) UNCONDITIONAL ......................................................................... 11
6.9
CF (CALL FORWARD) USER BUSY .................................................................................. 11
6.10 CF (CALL FORWARD) NO ANSWER................................................................................. 11
6.11 ANONYMOUS CALL ........................................................................................................ 12
6.12 ANONY CALL REJ (ANONYMOUS CALL REJECTION)...................................................... 12
6.13 RINGING TYPE ............................................................................................................... 12
6.14 MAC ADDRESS.............................................................................................................. 13
6.15 VERSION ........................................................................................................................ 13
6.16 LANGUAGE SELECTION .................................................................................................. 13
6.17 TIME FORMAT ................................................................................................................ 13
6.18 VOLUME ADJUSTMENT .................................................................................................. 14
6.18.1
Ringer Volume ...................................................................................................... 14
6.18.2
Speaker Volume .................................................................................................... 14
6.18.3
Handset Volume .................................................................................................... 14
7.0
USING THE CONFIGURATION MENU ................................................................... 15
ACCESSING CONFIGURATION MENU .............................................................................. 15
7.1
7.2
WEB LOGIN SETTING ..................................................................................................... 15
7.3
MANAGEMENT SETTING – RESTORE FACTORY SETTING ................................................ 16
7.4
MANAGEMENT SETTING – FIRMWARE UPDATE .............................................................. 17
7.5
NETWORK SETTING – DHCP ......................................................................................... 17
NETWORK SETTING – PPPOE......................................................................................... 18
7.6
7.7
NETWORK SETTING – STATIC IP .................................................................................... 18
7.8
SIP SETTING – SIP PHONE SETTING, REGISTRAR SERVER AND OUTBOUND PROXY
SERVER ...................................................................................................................................... 19
7.9
SIP SETTING – OTHERS .................................................................................................. 20
7.10 SIP ACCOUNT SETTING.................................................................................................. 21
7.11 STUN SETTING – STUN SERVER SETTING, UPNP SETTING ............................................. 22
7.12 VOICE SETTING AND QOS .............................................................................................. 22
7.13
7.14
7.15
7.16
7.17
7.18
7.19
8.0
PHONE SETTINGS – PHONE SETTING .............................................................................. 23
PHONE SETTING – TIMER ............................................................................................... 24
CALL TRACING LOG....................................................................................................... 25
PHONE BOOK ................................................................................................................. 26
SPEED DIAL ................................................................................................................... 26
LINE KEY SETTINGS ....................................................................................................... 27
RESTART SYSTEM .......................................................................................................... 28
OPERATING THE PHONE.......................................................................................... 29
8.1
DIALING ......................................................................................................................... 29
8.1.1
IP Address............................................................................................................. 29
8.1.2
SIP Number........................................................................................................... 29
8.2
SPEED DIALING .............................................................................................................. 30
8.3
ANSWERING A PHONE CALL .......................................................................................... 30
8.4
SWITCHING TO ANOTHER LINE ...................................................................................... 30
8.5
MUTE ............................................................................................................................. 30
8.6
CALL TRANSFER ............................................................................................................ 31
8.7
REDIAL .......................................................................................................................... 31
8.7.1
Last Dialed Number.............................................................................................. 31
8.7.2
Through Call History............................................................................................ 31
8.8
ON HOLD ....................................................................................................................... 32
8.9
CALL FORWARDING ....................................................................................................... 32
8.10 CALL WAITING (INTERNAL/EXTERNAL) ........................................................................ 32
8.11 ONE TOUCH DIAL .......................................................................................................... 32
8.12 THREE WAY CONFERENCE............................................................................................. 33
9.0
9.1
9.2
9.3
9.4
10.0
USING THE PHONEBOOK ......................................................................................... 34
DIALING FROM THE PHONEBOOK ................................................................................... 34
STORING A NUMBER ...................................................................................................... 34
EDITING A NUMBER ....................................................................................................... 34
DELETING A NUMBER .................................................................................................... 35
TROUBLESHOOTING ................................................................................................. 36
1.0 INTRODUCTION
Voice over IP (also known as Internet Phone) is a technology that allows anyone to make a
telephone call over the Internet. This is a quick user guide for the DPH-140S SIP Phone. It is
intended to help you configure the telephone and have it ready to run within a few minutes.
Please follow the user guide carefully as troubleshooting the telephone can be very difficult and
time consuming.
2.0 PACKAGE CONTENT
The following materials are included in the package. Please check the package to ensure that all
the materials are listed below. Contact your supplier immediately if an item is missing.
Ethernet Cable (1.8 metre)
IP Phone (Model: DPH-140S)
Power Adaptor (5V DC)
Wall Mount
CD
1
3.0 LIST OF FIGURES
Diagram for D-Link IP Phone (Model: DPH-140S)
(10) Phone Book
(1) 2 x 16 Characters
LCD Display
(11) Speed Dial
(2) Menu
(12) Cancel
(3) OK
(4) Control Pad
(13) Voice Message
Indicator
(14) Voice Message
(15) Mute/Func.
(5) 3-Way
Conference
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
Mu
te/
Fu
nc
.
Tr
a
(16) Transfer
(17) Redial/Call
History
(6) Local MultiLine
ns
fer
(7) Numeric Keypad
Re
dia
l
Ho
ld
(18) Hold
(8) Speaker Phone
(19) Mute Indicator
(9) Speaker Phone
Indicator
2
4.0 SUMMARY OF KEY FUNCTIONS
Keys
Functions
(1) LCD Display
Displays menu, time, clock, name, phone number, call status
(2) Menu
Access the phone menu
(3) OK
Confirm setting change, exit menu, dial, save changes
(4) Control Pad
Backspace, scroll up or down, select enable or disable
(5) 3-Way Conference
Enable 3-way conference
(6) Local Multiline
Switch to different lines
(7) Numeric Keypad
Input IP/phone number/alphabet characters
(8) Speaker Phone
Enable user to use the phone without using the handset
(9) Speaker Phone Indicator
Indicates that phone is currently in speaker phone mode
(10) Phonebook
Access the phonebook
(11) Speed Dial
Access the speed dial menu
(12) Cancel
Deny changes, cancel phone calls, ignore phone calls
(13) Voice Message Indicator
Indicates that there is a voice message
(14) Voice Message
Check voice message
(15) Mute/Func.
Disable user’s handset microphone so that the person on the
other line can not hear anything
(16) Transfer
Transfer the person on the other line to another number
(17) Redial/Call History
Redial last dialed number, access redial menu
(18) Hold
Place the person on the other line on hold
(19) On Hold Indicator
Indicates that the person on the other line is currently placed on
hold
3
5.0 CONNECTING THE IP PHONE
Connect the IP Phone as shown below.
Wide Area Network / Internet
Cable/xDSL Modem
Router/HUB
Ethernet Cable
Power Adapter
4
6.0 IP PHONE SETUP
6.1
Menu Summary
Press the MENU key
Display Name:
kevin
Enable
ADSL DIALUP:
ENABLE/DISABLE
ADSL DIALUP:
ENABLE
Disable
ADSL DIALUP:
DISABLE
ADSL ID:
mike_2004
ADSL Password:
********
Enable
DHCP:
ENABLE/DISABLE
Disable
IP Address:
AUTO
IP Address:
061.063.083.079
Subnet Mask:
AUTO
Subnet Mask:
255.255.254.000
Router IP:
AUTO
Router IP:
061.063.083.254
DNS Server IP:
061.063.082.001
SNTP Server IP:
216.133.140.77
5
ENABLE/DISABLE – select
enable or disable
AUTO – IP address given by
the router or ISP
SNTP Server IP – IP or URL
SNTP Cycle:
01
Do Not Disturb:
ENABLE/DISABLE
CF Unconditional:
ENABLE/DISABLE
CF User Busy:
ENABLE/DISABLE
CF No Answer:
ENABLE/DISABLE
Anonymous Call:
ENABLE/DISABLE
Anony Call Rej:
ENABLE/DISABLE
Ring Tone:
Ringing1/2/3/4
MAC Address:
00D0E90137DB
Version:
V: 1.0
Press the MENU key
UPDATE CHANGES?
<OK> OR <CANCEL>
6
Ringing1/2/3/4 - select
ringing1, 2 , 3 or 4
NOTE 1: If you made any modifications, you may quit setup at any time by pressing
+
save and exit or
+
to quit without saving. The phone will automatically exit
the menu screen if there are no inputs from the user.
NOTE 2: Use left
DISABLE.
and
NOTE 3: Left arrow key
6.2
Display Name
•
•
Press
Enter the display name
6.3
ADSL Dialup
right arrow on the direction pad to select ENABLE or
can be used as Backspace key.
Display Name:
kevin
Some Internet Service Provider (mostly ADSL) uses PPPoE which requires that the user enter an
ID and a password to access the Internet. In this case, enable ADSL DIALUP and enter the
PPPoE ID and PPPoE password.
ENABLE ADSL Dialup
1
•
Press
•
Use
to select ENABLE
ADSL DIALUP:
ENABLE
2
•
•
Press
Enter the ADSL ID
ADSL ID:
My_ID
7
3
•
Press
•
Enter ADSL password
ADSL Password:
*******
DISABLE ADSL Dialup
•
Press
•
Press
6.4
ADSL DIALUP:
DISABLE
to select DISABLE
DHCP (Dynamic Host Configuration Protocol)
DHCP allows the network administrator to distribute IP addresses when a computer is plugged
into a different place in the network. If your ISP provides static IP address, you must disable
DHCP and enter the IP address provided.
ENABLE DHCP
1
•
Press
•
Use
or
to set DHCP to ENABLE
DHCP:
ENABLE
2
•
•
Press
IP Address:
61. 63. 83. 96
IP address automatically acquired
8
3
•
•
Press
Subnet Mask:
255.255.254.
Subnet mask automatically acquired
0
4
•
•
Press
Router IP:
61. 63. 83.254
Router IP automatically acquired
DISABLE DHCP
1
•
•
Press
Use
or
to set DHCP to DISABLE
2
•
•
Press
Enter the IP address
IP Address:
061.063.083.019
9
DHCP:
DISABLE
3
•
•
Press
Subnet Mask:
255.255.254.000
Enter the subnet mask
4
•
Press
•
Enter the router IP address
6.5
Router IP:
061.063.082.019
DNS Server IP
The domain name system (DNS) is the way that Internet domain names are located and
translated into Internet Protocol addresses. There is probably a DNS server within close
geographic proximity to your ISP that maps the domain names in your Internet requests or
forwards them to other servers in the Internet.
•
•
6.6
Press
Enter DNS server IP
DNS Server IP:
061.063.082.001
SNTP Server IP
Simple Network Time Protocol (SNTP) is a protocol used to help match your system clock with
an accurate time source. If you do not know your SNTP Server IP, please ignore this section.
SNTP Server IP address can be either URL or IP.
•
Press
SNTP Server IP:
216.133.140.78
•
Enter SNTP server IP or URL
10
6.7
Do Not Disturb
This setting allows the user to reject all incoming phone calls.
•
Press
•
Use
6.8
or
to select ENABLE or DISABLE
Do Not Disturb:
DISABLE
CF (call forward) Unconditional
Enable CF Unconditional to forward all the incoming calls to another number. Otherwise set to
disable. You will need to use a web-browser to input the forwarded phone number. Refer to
section 7.0 for more information on call forwarding.
•
Press
•
Use
6.9
or
to select ENABLE or DISABLE
CF Unconditional:
DISABLE
CF (call forward) User Busy
Forward all the incoming calls to another number when user is busy on the phone.
•
•
6.10
Press
Use
or
to select ENABLE or DISABLE
CF User Busy:
DISABLE
CF (call forward) No Answer
Forward all incoming calls to another phone number after a certain number of rings.
•
•
Press
Use
or
to select ENABLE or DISABLE
11
CF No Answer:
ENABLE
6.11
Anonymous Call
Enables the caller (user) to hide the name and phone number from the receiver.
•
Press
•
Use
6.12
or
to select ENABLE or DISABLE
Anonymous Call:
ENABLE
Anony Call Rej (Anonymous Call Rejection)
Reject any anonymous incoming calls.
•
•
6.13
Press
Use
or
to select ENABLE or DISABLE
Anony Call Rej:
DISABLE
Ringing Type
Select the ring tone. There are four ring tones in total.
•
Press
•
Use
or
to select the ring type
Ringing Type:
Ringing4
NOTE: At this point, you may save the settings and exit. The next two sections explain how to
obtain the MAC address and firmware version.
•
Press
•
When asked to save or cancel, press
to exit menu
to SAVE
12
6.14
MAC Address
This menu displays the MAC address. User cannot modify MAC address.
•
Press
•
MAC address is displayed on the screen
6.15
MAC Address:
00D0E9017DB
Version
Version menu displays the firmware version. You cannot modify the version number.
•
Press
•
Firmware version is displayed on screen
6.16
Version:
V: 02.08
Language Selection
The VoIP Phone (model no. DPH-140S) supports two languages: Japanese and English.
Mu
te/
Fu
nc
.
•
Press
•
Use
or
•
Press
when done
6.17
Language:
English
followed by
to select the preferred language
Time Format
You may select the 12hr or 24hr time format.
Mu
te/
Fu
nc
.
•
Press
•
Use
•
Press
Time Format:
24Hours
followed by
or
to select the time format
when done
13
6.18
Volume Adjustment
6.18.1 Ringer Volume
While the handset is in place,
•
Press
to increase the ringer volume and
to decrease the
ringer volume
6.18.2 Speaker Volume
While the handset is in place,
•
Press
•
Press
to increase the speaker volume and
to decrease the
speaker volume
6.18.3 Handset Volume
•
Pick up the handset and press
to increase the volume or press
to decrease the volume
14
7.0 USING THE CONFIGURATION MENU
The configuration menu can be accessed using a web browser. Some advanced functions such as
CF Unconditional, CF User Busy and CF No Answer must be setup from the web browser.
7.1
Accessing Configuration Menu
•
Open the web browser (ie. Internet
Explorer, Netscape…)
Type in the IP Address of the phone
followed by :9999
•
IP address is provided by your Internet Service Provider (ISP). If your ISP supports DHCP, you
may obtain the IP address from you phone. Press MENU and scroll down to IP address.
•
•
Enter User Name and Password (leave
User Name and Password blank if you
are installing the phone for the first
time)
Click OK
7.2
Web Login Setting
15
User Name
Configuration menu login name.
Password
Configuration menu login password.
NTP Server IP
Network Time Protocol (NTP) is a protocol used to help
match your system clock with an accurate time source (eg
atomic clock, server). It is good practice to have all your
networked computers synchronized with one server.
Time Zone
Select your time zone. If there is daylight saving in your
area, click the check box.
TFTP Server
Enable or disable TFTP server to allow transfer of files
from a computer to the IP phone.
FTP Client
Enable or disable IP phone to download files from FTP
server and update the firmware automatically.
Remote Config Password
Remote password to access the configuration menu from
VoIP software. (You may download this software from
your supplier’s website). Default password is 1234.
7.3
Management Setting – Restore Factory Setting
Click on Management. Select Restore Factory Setting and the above screen will display on the
screen.
Restore Factory Setting
Restores all the settings back to factory default settings.
16
7.4
Management Setting – Firmware update
FTP server, login ID, login password and firmware filename are preset when you purchase the
phone. These are required to download and update the firmware.
FTP Server
FTP Server address.
Login ID
Login ID provided by your supplier.
Login Password
Login password provided by you supplier.
Firmware Filename
Updated firmware filename. Do not change the file name
unless specified by your supplier.
7.5
Network Setting – DHCP
Select DHCP if you have cable internet.
DHCP Server
Dynamic Host Configuration Protocol (DHCP) Server
address. This IP address information is obtained
automatically from your ISP.
DNS Server
DNS address is provided by your ISP.
17
7.6
Network Setting – PPPoE
Choose PPPoE if your ISP uses PPPoE. Most DSL users use PPPoE.
PPPoE ID
PPPoE ID/username provided by your ISP.
PPPoE Password
PPPoE password.
DNS address provided by your ISP.
DNS Server
7.7
Network Setting – Static IP
Choose Static IP network setting if all Wide Area Network IP is provided to you by your ISP.
IP Address
IP address assigned to you by your ISP.
Router IP
Router IP address.
Subnet Mask
Subnet mask address.
DNS Server
DNS server address provided by your ISP.
18
NOTE: RESTART the system for new settings to take effect after you modify the IP address.
7.8
SIP Setting – SIP Phone Setting, Registrar Server and Outbound Proxy Server
Session Initiation Protocol (SIP) is the most popular Voice over IP standard. It enables two or
more people to make phone calls, share multimedia and make multimedia conference over the
internet. Please have an administrator setup these settings for you or obtain this information from
your SIP service provider.
SIP Phone Port Number
SIP phone port number.
Registrar Server Domain
Name/IP Address
Registrar server domain name or IP address.
Registrar Server Port
Number
Registrar server port number.
Authentication Expire
Time
The time that the phone waits to connect to the SIP
server after the user dialed a number. If still not
connected, the phone will disconnect and redial.
Outbound Proxy Domain
Name/IP Address
Outbound proxy domain name or IP address.
Outbound Proxy Port
Number
Outbound proxy port number.
19
7.9
SIP Setting – Others
This section is for network administrators.
Session Timer
The time interval in which the phone periodically refresh
SIP sessions by sending repeated INVITE requests. These
INVITE requests allow the user agent or proxies to
determine the status of the SIP session.
Media Port
Real-time Transport Protocol port number. Provides endto-end transfer of data with real-time audio.
Prack
Prack ensures that media information is exchanged and
that network checks before connecting the call. Select
Enable for a more reliable connection.
Session Refresher
Select None to disable SIP session timer support.
Select UAC to initiate SIP request.
Select UAS to receive SIP request and then return a
response.
Session Timer Method
Select SIP request method. Default method is Invite.
UDP/TCP
Select SIP signal transmission method. Default method is
UDP.
20
7.10
SIP Account Setting
You may have up to 4 accounts. i.e., the IP phone can receive up to four different phone
numbers.
Default Account
When you dial a number, the default account is used to
dial. User Name of default account is displayed on the
receiver’s IP phone.
Account Active
Enable or disable this account.
Display Name
Display name on the IP phone.
SIP User Name
User name.
Authentication User Name
Name used to access SIP server.
Authentication Password
User password to access SIP server.
Register Status
Displays if the current phone is registered or
21
7.11
unregistered with SIP server.
Stun Setting – Stun Server Setting, UPnP Setting
Setup STUN and UPnP if VLAN (sec 7.12) is set to ENABLE.
STUN
Simple Traversal of User Datagram Protocol Through
Network Address Translators is a protocol that allows
applications to determine the types of NATs and firewalls
are in between them and the internet. STUN also provides
the ability for applications to determine the public IP
addresses allocated to them by the NAT.
STUN Domain Name/IP
Address
Enter STUN domain name or IP address if STUN is
enabled.
UPnP
Enable or disable universal plug and play. Some NAT
supports UPnP so STUN is not required and must be
disabled.
7.12
Codec
Voice Setting and QoS
Voice Compression Algorithm priority settings. Select
22
from the most used codec to the least used codec.
RTP Packet Length
Real-Time Transfer Protocol (RTP) packet length.
VAD
VAD detects voice activity and adjusts the signal to a
target power level. It ensures that background noise or
echo does not get amplified to the target power level.
DTMF Method
Select the tone method for IP phone.
Voice TOS
Sets the type of service for this Internet datagram.
VLAN
Enable or disable virtual LAN.
VLAN Priority
Set the virtual LAN Priority.
VLAN ID
Virtual LAN ID.
7.13
Phone Settings – Phone Setting
Recall you can only enable or disable call forwarding from the IP phone MENU key. With the
web-browser, you can enter the forwarded phone numbers in the Phone Setting menu.
Tone Setting
Select the tone for particular country
Ringer Type
Select the type of ring (1 to 4).
Hold Tone
Select melody or tone when HOLD key is pressed.
23
Do Not Disturb
Reject all incoming calls.
Call Waiting
Enable or disable call waiting.
Anonymous Call
If DISABLE is selected, full URI and name are sent to the
receiver’s phone when the user makes a phone call. The
URI and name of the caller are displayed on the receiver’s
phone.
When Full URI is selected, only user name is displayed on
the receiver’s phone when the user makes a phone call.
When Display Name is selected, only name is displayed
on the receiver’s phone when the user makes a phone call.
Anonymous Call Reject
Select Enable to reject anonymous calls.
Call Forward
Click No Answer to enable call forward to another number
when no one answers the phone after 180s (default). The
timer can be changed from 0-600s. Refer to section 7.14 to
change the timer.
Click Busy to enable call forward to another number when
user is busy on the phone.
Click Unconditional to transfer all incoming calls to
another number.
Enter the call forward number on the text box.
7.14
Phone Setting – Timer
NTP Recycle
NTP recycle time.
24
Inter Digit
The time interval that the IP phone waits to detect the end
of DTMF digits. No more digits are accepted after this
period and the phone begins to dial.
Originating Not Accept
The time interval that the caller’s phone waits to establish
a call. If the receiver fails to answer the phone during this
time interval, the caller’s phone will automatically
disconnect.
Incoming No Answer
The time interval that the receiver’s phone will ring. If the
receiver fails to answer the phone during this time
interval, the phone will automatically disconnect.
Hold Recall
The time interval that the caller is put on hold before the
phone automatically disconnect.
Auto Speaker Off
The time interval that the speaker phone is on before
turning off automatically (due to inactivity).
7.15
Call Tracing Log
Call Tracing Log keeps a record of all the phone activities. This log is used by our engineers to
troubleshoot hardware problems.
25
7.16
Phone Book
Phonebook menu allows the user to add, modify and delete phone numbers. To add, type in the
name and number then click NEW to add. To modify/delete, select the name from the list and
click modify/delete.
Name
Name that you would like to add.
Number
Phone number that corresponds to the name.
7.17
Speed Dial
Speed dial numbers can be accessed from the IP phone. Refer to section 8.2 for speed dial info.
26
Number 0x
7.18
Speed dial phone number. 0x is the speed dial number.
Line Key Settings
Line Key Settings allows the user to customize line keys as a line or one touch dial. Refer to
section 8.11 for one touch dial info.
Key Type
Select local multiline key (M2~M10) as line or one touch
dial function.
Telephone Number
Enter the phone number when key type selects to one
touch dial function.
27
7.19
Restart System
Click Restart to update all the modifications.
28
8.0 OPERATING THE PHONE
8.1
Dialing
8.1.1
IP Address
1.
Lift handset
2.
Dial IP address.
or press SPEAKER button
For example: dialing 192.168.0.1
3.
Press OK
or wait until the timer expires to dial.
8.1.2 SIP Number
Note: You have to register with SIP server to use SIP number.
1.
Lift handset
2.
Dial SIP number.
or press SPEAKER button
For example: dialing 1866
3.
Press OK
or wait until the timer expires.
29
8.2
Speed Dialing
1.
Lift handset
2.
Dial Speed Dial number.
or press SPEAKER button
For example: dialing speed dial number 08
8.3
Answering a Phone Call
Note: The CANCEL key may be used to reject a call.
When phone rings:
1.
Lift handset
or press SPEAKER button
to begin conversation.
8.4
Switching to Another Line
While having a conversation:
1. Press the flashing local multiline key M1
M10
M1
to M10
to switch to
another line.
8.5
Mute
Note: While mute is activated, sound from the caller can be heard from your speaker but your
sound can’t be heard by the caller.
While having a conversation:
1.
Mu
te/
Fu
nc
.
Press Mute
. You may press Mute key again to resume conversation.
30
8.6
Call Transfer
While having a conversation:
1.
2.
3.
8.7
Tr
an
sfe
r
Press Transfer
to put the person on the other line on hold.
Dial the IP address or the extension number where you like the call to be
transferred.
Tr
an
sfe
r
Press Transfer
to transfer the call.
Redial
Note: To return to idle mode, press CANCEL key
8.7.1
Last Dialed Number
1.
Lift handset
or press SPEAKER button
Re
dia
l
2.
Press Redial
8.7.2
Through Call History
1.
2.
3.
4.
to dial the last dialed number.
Re
dia
l
Press Redial
. Do not lift the handset when you press Redial.
Re
dia
l
Press Redial
calls.
again to cycle through the dialed, missed and received
Press DOWN key
to scroll down the dialed, missed or received lists
until the number is displayed on the screen.
Press LEFT
every call.
or RIGHT key
31
to show the detail information of
5.
8.8
Pickup the handset
or press OK
On Hold
While having a conversation:
Ho
1.
ld
Press HOLD
(Press HOLD again to resume conversation)
8.9
Call Forwarding
Please refer to IP Phone Setup and Web Browser Configuration section to setup call
forwarding.
8.10
Call Waiting (Internal/External)
While having a conversation:
1.
2.
8.11
M10
M1
Press the flashing local multiline key M1
to M10
to pickup
another incoming call. The first caller is automatically placed on hold.
M10
M1
Press the flashing local multiline key M1
to retrieve the call again.
to M10
of the first caller
One Touch Dial
While one of local multiline key (M2~ M10) selects as one touch dial function from web
setting:
1.
Press the pre-
32