Type No. L19C0D060

Daewoo Computer F109A1

Dual Function Monitior

User’s Guide

NEXT

U.S.A.

U.S.FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet of a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for assistance.

Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Connecting of peripherals requires the use of grounded shielded signal cables.

BACK

NEXT

Contents

F109A1

19" D ual Function Monitor

BACK

NEXT

1. Introduction ...................................1/22

2. Safety Information ........................1/22

3. Installing the monitor ...................4/22

3-1. Packing List .........................................4/22

3-2. Selecting a suitable location ..............5/22

3-3. Connecting the monitor .....................5/22

3-4. Setting the refresh rate ......................8/22

Preset Timing Table ............................8/22

3-5. User’s Environment ...........................10/22

4. Adjusting the picture ..................12/22

4-1. Using the On Screen Display ...........14/22

4-2. Direct access buttons .......................14/22

4-3. OSD Adjustments .............................15/22

5. Display power management ......18/22

Reducing power consumption ..............18/22

6. Troubleshooting ..........................19/22

7. Specifications ..............................22/22

1. Introduction

2. Safety Information

F109A1

19" Dual Function Monitor

BACK

NEXT

This manual contains instructions for installing and operating Daewoo Computer

F109A1.

Daewoo Computer F109A1 is a highly ergonomic color display unit.

• 19" viewable SXGA LCD

• High quality screen re-scaling capability

• 100-240V AC input voltage

• VESA DPMS (Display Power Management Signaling)

• VESA DDC1/2B compatibility

• Advanced digital On-Screen-Display controls

• Fast and accurate auto adjustment

• Most advanced image scaling

• Supporting VESA Flat Panel Monitor Physical Mounting Interface

This Monitor has been engineered and manufactured to assure your safety.

You can prevent serious electrical shock and other hazards by keeping in mind the following:

Do not place anything wet on the monitor or the power cord. Never cover the ventilation openings with any material and never touch them with metallic or inflammable materials.

1/22

F109A1

19" Dual Function Monitor

BACK

NEXT

Avoid operating the monitor in extreme heat, humidity or areas affected by dust.

Temperature : 5~35°C

Humidity : 30~80RH

Be sure to turn the monitor off before plugging the power cord into the socket. Make sure that the power cord and the other cords are securely and rightly connected.

Overloaded AC outlets and extension cords are dangerous, as are frayed power cords and broken plugs, which may cause electric shock or fire. Call your service technician for replacement.

Do not use sharp tools such as a pin or a pencil near the monitor, as they may scratch the LCD surface.

Do not use a solvent, such as benzene, to clean the monitor, as it will damage the LCD surface.

2/22

BACK

F109A1

19" Dual Function Monitor

NEXT

Cleaning and Maintenance

• To avoid risk of electric shock, do not disassemble the display unit cabinet. The unit is not user-serviceable. Remember to unplug the display unit from the power outlet before cleaning.

• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do not use thinner or benzene, abrasive cleaners or compressed air.

• Do not wipe the screen with a cloth or sponge that could scratch the surface.

• To clean your antistatic screen, use water and a special microfiber screen cleaning tissue used in optical lens cleaning, or lightly dampen a soft, clean cloth with water or a mild detergent.

• If the instructions above do not help in removing stains, contact an authorized service agent.

3/22

3. Installing the monitor

3-1. Packing List

F109A1

19" Dual Function Monitor

BACK

NEXT

The following items should be found in the packaging.

Power Cord

Signal Cable

DVI-D Cable

Audio Cable

Compact Disc

!

Above power cord can be changed upon different voltage areas. Please contact your dealer if anything is missing or damaged.

Other power cord except the cord packed in the product or longer than 3m may affect EMC of the product in operating condition.

4/22

BACK

F109A1

19" Dual Function Monitor

NEXT

3-2. Selecting a suitable location

3-3. Connecting the monitor

• 15 pin D-sub / DVI-D

• Place the monitor at least 30cm from other electrical or heat-emitting equipment and allow at least 10cm on each side for ventilation.

• Place the monitor in a position where no light shines directly onto or is reflected on the screen.

• To reduce eye strain, avoid installing the display unit against a bright background such as a window.

• Position the monitor so that the top of the screen is no higher than eye level.

• Position the monitor directly in front of you at a comfortable reading distance

(around 45 to 90cm)

!!

Before you start cabling your monitor, check that the power is off on all units. To avoid any possibility of electric shock, always connect your equipment to properly earthed outlets.

1. Insert the other 15-pin/DVI-D signal cable connector into the 15-pin VGA/DVI-D connection on your computer and screw it down.

2. Plug the power cord connection to connection on the monitor.

3. Plug the other end of the power cord to your computer's main supply or to a

100V-240V earthed electrical outlet.

4. Turn on the monitor using the power switch and check that the power LED is on. If not, repeat steps 1,2,3 and 4 or refer to the Troubleshooting section of this guide.

5/22

F109A1

19" Dual Function Monitor

5. Turn on the power to the computer. The picture will appear within about 10 seconds. Adjust the picture to obtain optimum picture quality. See section

Adjusting the picture in this guide for more information.

15 pin D-sub cable (Analog RGB)

BACK

NEXT

DVI-D cable (Digital TMDS)

6/22

• Audio system

F109A1

19" Dual Function Monitor

BACK

NEXT

This monitor has an audio system including two micro loudspeakers. Each of two micro loudspeakers has an 2Wrms (typ.) output power. This system also supports a headphone output jack.

!!

This system has been tuned to get a best tone quality which an audio input level is under 300mVrms. if the input level is more than 600mVp-p, you must tune down the audio input as the audio output tone may be distorted.

When this monitor is turned on, audio is always set up as off mode. Please use

AUDIO direct access button on the front cover or On Screen Display to put audio on.

Speaker

Power Switch

7/22

F109A1

19" Dual Function Monitor

BACK

NEXT

3-4. Setting the refresh rate

Preset Timing Table

Follow the instructions below to set your refresh rate in Windows 98/ME/XP/2000.

1. Go to the configuration window(Start-Settings-Configuration window).

2. Double click on the ‘Display’ icon.

3. Click on the ‘Settings’ tab.

4. Click on the ‘Advanced’ button.

5. Click on ‘Adapter’ and select 60Hz from the list.

6. Click on ‘Apply’ to accept the selected value.

!

If the signal from the system doesn't equal to the preset timing mode, adjust the mode with reference to the user guide of videocard because the screen may not be displayed.

DIGITAL R.G.B INPUT

No.

3

4

1

2

Resolution

640 x 480

800 x 600

1024 x 768

1280 x 1024

Horizontal Frequency

31.5 KHz

37.9 KHz

48.4 KHz

63.9 KHz

Refresh rate

60 Hz

60 Hz

60 Hz

60 Hz

8/22

Preset Timing Table

BACK

F109A1

19" Dual Function Monitor

ANALOG R.G.B INPUT

The recommended setting is a resolution of 1280x1024 and a refresh rate of 60Hz.

No.

9

10

11

12

7

8

5

6

13

14

1

2

3

4

Resolution

720 x 400

640 x 480

640 x 480

800 x 600

800 x 600

800 x 600

800 x 600

832 x 624

1024 x 768

1024 x 768

1024 x 768

1152 x 864

1280 x 1024

1280 x 1024

Horizontal Frequency

31.5 KHz

31.5 KHz

37.5 KHz

35.2 KHz

37.9 KHz

48.1 KHz

46.9 KHz

49.7 KHz

48.4 KHz

56.5 KHz

60.0 KHz

67.5 KHz

63.9 KHz

80.0 KHz

Refresh rate

70 Hz

60 Hz

75 Hz

56 Hz

60 Hz

72 Hz

75 Hz

75 Hz

60 Hz

70 Hz

75 Hz

75 Hz

60 Hz

75 Hz

NEXT

9/22

F109A1

19" Dual Function Monitor

BACK

NEXT

3-5. User’s Environment

Recommended Ergonomic User’s Environment

• Viewing angle of the monitor should be between 0~20 degree.

20 o

Kensington Security

(Locking) Slot

Kensington security slot

• This display unit supports a Kensington-type security device to secure your monitor. Kensington lock is not included.

• To purchase and install the Kensington locking device, please refer to the following contact information.

* Kensington Technology Group

· Address : 2000 Alameda de las Pulgas 2F san mateo, California 94403-1289

· Tel : +1 650 572 2700 · Fax : +1 650 572 9675 · Web-site : www.kensington.com

10/22

VESA MOUNT’G

F109A1

19" Dual Function Monitor

BACK

NEXT

• This display unit supports VESA FPMPMI standard for 75mmx75mm screw mounting by giving 4 screw holes inside the base stand of the unit.

• For buying VESA Flat Panel Monitor Mounting Devices, please contact following information.

* Ergotron, Inc.

· Address : Ergotron Europe Kuiperbergweg 50 1101 AG Amsterdam The Netherlands

· Tel : +3 1 20 696 60 65 · Fax : +3 1 20 609 04 59 · E-mail : [email protected]

Desk Mount

Wall Mount

11/22

F109A1

19" Dual Function Monitor

BACK

NEXT

4. Adjusting the picture

You can adjust the screen display by using the buttons located below the screen.

In case of applying Analog RGB Input

1280x1024

H:63.9 V:60.0

BRIGHTNESS

12/22

F109A1

19" Dual Function Monitor

BACK

NEXT

In case of applying Digital TMDS Input

1280x1024

H:63.9 V:60.0

BRIGHTNESS

13/22

BACK

F109A1

19" Dual Function Monitor

NEXT

4-1. Using the On Screen

Display

4-2. Direct access buttons

1. Push the MENU button to call the OSD to the screen. The resolution and frequency are displayed at the top of the menu box for your information.

2. Push the or button to choose the item you want to adjust. The selected item is highlighted.

3. Push the SELECT button to adjust the highlighted item.

4. Use the or button to adjust the selection.

5. Push the MENU button to return to the previous menu if you are in a submenu.

6. The display unit automatically saves the new settings in 1 second after your last adjustments and the menu disappears. You can also push the MENU button to make the menu disappear.

AUTO ADJUST

At first display a full screen such as Window's back ground.

Push the button SELECT(AUTO) to adjust the shape of screen automatically.

VOLUME

Use the button to select the volume adjustment.

Adjust with or button.

AUDIO

Push the button to choose audio on or off.

14/22

4-3. OSD Adjustments

F109A1

19" Dual Function Monitor

BACK

NEXT

The OSD adjustments available to you are listed below.

BRIGHTNESS

Adjust the brightness of the screen.

CONTRAST

Adjust the contrast of the screen.

COLOR CONTROL

Color temperature affects the tint of the image. With lower color temperatures the image turns reddish and with higher temperatures bluish.

There are three color settings available: Mode 1(a cool white), Mode 2(a warm white) or USER. With the USER setting you can set individual values for red, green and blue.

POSITION

H POSITION

Adjusts the horizontal position of the entire screen image.

V POSITION

Adjusts the vertical position of the entire screen image.

15/22

F109A1

19" Dual Function Monitor

BACK

NEXT

CLOCK PHASE

PHASE

Adjust the noise of the screen image.

CLOCK

Adjust the horizontal size of the entire screen image.

MISCELLANEOUS

RECALL

Recall the saved color data.

OSD TIMER

You can set the displayed time of OSD Menu window on the screen by using this adjustment.

OSD POSITION

Adjust the OSD menu's horizontal or vertical position on the screen.

AUTO COLOR

Optimum color setting is auto programmed for user’s convenience.

LANGUAGE

You can select the language in which adjustment menus are displayed.

The following languages are available : English, French, German, Italian,

Spanish, Swedish, Finnish, Danish, Portuguese, Dutch and Japanese.

16/22

F109A1

19" Dual Function Monitor

BACK

NEXT

AUDIO

VOLUME

Adjust the audio volume level.

AUDIO

This menu is used to choose audio on or off.

AUTO ADJUST

You can adjust the shape of screen automatically at the full screen pattern.

INPUT SELECT

This menu used to choose the desired input signal source.

There are two available signal source.

• Analog R.G.B : 15 pin D-sub, Analog Signal

• Digital TMDS : 24 pin DVI-D, Digital Signal

!

In case of applying Digital TMDS Input, the functions of Color Control, Auto

Adjust, Position, Clock Phase, Auto Color are not supported.

17/22

5. Display power management

Reducing power consumption

F109A1

19" Dual Function Monitor

BACK

NEXT

If the power management function of your computer is enabled, your monitor turns on and off automatically. You can control power management features from your computer.

Your computer may have power management features which enable the computer or monitor to enter a power saving mode when the system is idle. You can reactivate the system by pressing any key or moving the mouse.

Mode

Normal off

Unplugged

LED

Green

Orange

Not illuminated

Power consumption

40 W

3.5 W

0 W

!

The power button does not disconnect the monitor from the mains. The only way to isolate the monitor completely from the mains supply is to unplug the mains cable.

18/22

6. Troubleshooting

F109A1

19" Dual Function Monitor

BACK

NEXT

If your monitor is not functioning properly, you may be able to solve the problem by following the suggestions below :

Problem Possible solution

Blank screen If the power LED is not lit, push the Soft power switch or check the

AC cord to turn the monitor on. If the display unit is powered through the computer, check that the computer is switched on.

The display unit might be in standby mode. Push one of the keyboard keys. Check that the keyboard is properly connected to the computer.

Check that the signal cable connector is properly connected and that the connection pins are not bent or damaged. If the connector is loose, tighten the connector's screws.

Check that the power cable is correctly connected to the display unit and to the power outlet.

Error message:

Video mode not supported

Check the resolution and the frequency on the video port of your computer.

Compare these values with the data in the Preset Timing Table.

The display does not enter power management mode

The video signal from the computer does not comply with VESA

DPMS standard. Either the computer or the graphics adapter is not using the VESA DPMS power management function.

19/22

F109A1

19" Dual Function Monitor

BACK

NEXT

Problem

Color defects

Size, position, shape or quality unsatisfactory

Duplicated images

Image is not stable

Message :

No signal

The power LED is a orange color

Possible solution

Check that the signal cable connector is properly connected and that the connection pins are not bent or damaged. Try another color temperature.

Adjust the picture characteristics as described in the section OSD

Adjustment(4-3).

A problem with your graphics adapter or display unit. Contact your service representative.

Check that the display resolution and frequency from your PC or graphic adapter is an available mode for your monitor.

In your PC, you can check through Control panel, Display, Settings.

If the setting is not correct, use your computer utility program to change the display settings.

Check that the signal cabel connector is properly connected and that the connection pins are not bent or damaged.

If the connector is loose, tighten the connector’s screws.

Check that the computer is switched on.

To enter a power saving mode. You can reactivate the system by pressing any key or moving the mouse.

20/22

Contacting service

F109A1

19" Dual Function Monitor

BACK

NEXT

Problem

The power LED is a orange color

Possible solution

LED Indicator can be orange color on changing of video mode or

Input Signal.

Check the Resolution and the frequency on the video part of your computer. Compare these values with the data in the Preset Timing

Table.

If the above troubleshooting hints do not help you find a solution to the problem, contact an authorized service agent. If the monitor is sent for service, use the original package if possible.

Unplug the display unit from the power outlet and contact a service agent when:

• The monitor does not operate normally according to the operating instructions.

• The monitor exhibits a distinct change in performance.

• The monitor has been dropped or the cabinet has been damaged.

• The monitor has been exposed to rain, or water or liquid has been spilled onto the monitor.

21/22

7. Specifications

F109A1

19" Dual Function Monitor

BACK

LCD

Pixel pitch

Brightness

Response Time

Display area

Number of color

Input signals

Frequency rate

Maximum bandwidth

Maximum resolution

Recommanded resolution

Input voltage

Power consumption

Power management

Plug & Play

OSD menu

Built in Speaker

VESA FPMPMI

Ergonomics,

Safety and EMC

Operating Temperature

Weight

Dimensions (W X H X D mm)

19"viewable, Diagonal, A-Si TFT

0.294 x 0.294 mm

250cd/m 2

25msec

376.32 x 301.056 mm

16,7 milion colors

R.G.B Analog, Digital TMDS(DVI-D)

Horizontal : 31.0 to 80.0KHz, Vertical : 56 to 75Hz

135 MHz

1280 x 1024@75Hz

1280 x 1024@60Hz

100-240 VAC, 1.0A

40W

VESA DPMS

VESA DDC 1/2B

BRIGHTNESS, CONTRAST, COLOR CONTROL, POSITION,

CLOCK-PHASE, MISCELLANEOUS, LANGUAGE, AUDIO,

AUTO ADJUST, INPUT SELECT

2ch x 2watts / EarPhone Jack & Speaker

75 x 75 mm screw mounting

TCO, FCC Class B, CE, cULus, TÜV-GS, ISO 13406-2

5 ~ 35 O C

6.2Kg unpacked, 8.2Kg packed

420 X 441 X 185 mm

• Specification is subject to change without notice for performance improvement.

22/22