D1901N
18.5" wide LCD Monitor
User Manual
English
3\FFɤɢɣ
Deutsch
Français
Svenska
Suomi
Italiano
Español
Dansk
ㅔԧЁ᭛
Polski
Nederlands
穢剳檺
Model: D1901Nc
ModelM
TABLE OF CONTENTS
FOR YOUR SAFETY ----------------------------------------------------------- 1
SAFETY PRECAUTIONS ------------------------------------------------ 2
SPECIAL NOTES ON LCD MONITORS ----------------------------- 3
BEFORE YOU OPERATE THE MONITOR ------------------------------FEATURES -----------------------------------------------------------------PACKING LIST ------------------------------------------------------------INSTALLATION INSTRUCTIONS -----------------------------------CONTROLS AND CONNECTORS -----------------------------------ADJUSTING THE VIEWING ANGLE ---------------------------------
3
3
3
4
5
6
OPERATING INSTRUCTIONS ---------------------------------------------- 7
GENERAL INSTRUCTIONS -------------------------------------------- 7
HOW TO ADJUST A SETTING ---------------------------------------- 9
ADJUSTING THE PICTURE ---------------------------------------- 10-11
PLUG AND PLAY ---------------------------------------------------------- 12
TECHNICAL SUPPORT(FAQ) ----------------------------------------- 13-14
ERROR MESSAGE & POSSIBLE SOLUTION ------------------ 15
APPENDIX ----------------------------------------------------------------------- 16
SPECIFICATIONS ---------------------------------------------------- 16-17
FACTORY PRESET TIMING TABLE -------------------------------- 18
CONNECTOR PIN ASSIGNMENT ----------------------------------- 18
Before operating the monitor, please read this manual thoroughly. This
manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the
cabinet. Refer servicing to qualified personnel only.
1
PRECAUTIONS
• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
• Do not place the monitor on an unstable cart, stand, or table. If the monitor
•
•
•
•
•
•
•
•
falls, it can injure a person and cause serious damage to the appliance.
Use only a cart or stand recommended by the manufacturer or sold with
the monitor. If you mount the monitor on a wall or shelf, use a mounting kit
approved by the manufacturer and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as
a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground
the appliance safely. Do not defeat the safety purpose of the grounded
plug.
Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to
power surges.
Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
The wall socket shall be installed near the equipment and shall be easily
accessible.
2
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
• Due to the nature of the fluorescent light, the screen may flicker during
•
•
•
•
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.
When the screen becomes black or flashing, or cannot illuminate any more,
contact your dealer or service center to replace parts. Don’t repair the
screen by yourself!
BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
•
•
•
18.5” (470 mm) Wide ScreenTFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommended Resolutions: 1366x768@60Hz
Ergonomic Design
Space Saving, Compact Case Design
PACKAGE LIST
The product package should include the following items:
1.
2.
3.
4.
LCD Monitor
Owner's Manual
Power Cable
Signal Cable
3
INSTALLATION INSTRUCTIONS
Install
Figure 1
Remove
Installing and Removing the Base
POWER CORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s power input socket,
The AC-power cord may be connected to either a wall power outlet or the
power outlet socket on your PC, depending on the type of power cord
supplied with your LCD monitor.
CONTROLS AND CONNECTORS
SIGNAL CABLE
Connecting the Signal Cable: Plug the Signal Cable one end to LCD
monitor’s “DSUB-Input” socket , the other end to the computer’s VGA port and
tighten the two screws on the cable connector.
Connecting the Power Cord: Plug one end of the AC power cord to the
LCD monitor's AC input socket, and the other end to Wall outlet.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
1
Figure 2
1.
2.
Power Cable
Signal Cable
2
Connecting Cables
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
• You are able to adjust the monitor’s angle from -5° to 20°.
Figure 3
NOTES
• Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
• Careful attention is required not to catch your fingers or hands when you
change the angle.
6
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons
are located at front panel of the monitor (See Figure 4). By changing these
settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator
will light up.
6 5 4 3 2
Figure 4
1.
2
3.
4.
5.
6.
External Control Button
Power button
Power Indicator
MENU
Image Ratio(+)
ECO Hotkey(-)
Auto/Source
7
1
FRONT PANEL CONTROL
• Power Button:
Press this button to switch ON/OFF of monitor’s power.
• Power Indicator:
Blue — Power On mode.
Orange — Power saving mode.
• MENU/ENTER :
Active OSD menu or function adjust confirm or Exit OSD menu when in
Contrast/Brightness OSD status.
• ECO Hotkey(-)
Activates the ECO control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. • Image Ratio(+) :
Select monitor display mode. Press Image Ratio(+) button to change wide
mode or 4:3 mode.
• Auto/Source:
1. When the OSD is off, press Auto/Source button continuously to select the
input source showed in the message bar. Press Menu/Enter button to
change to the selected source.
2. Auto configure hot key: When the OSD is closed, press Auto/Source
button continuously about 2 second to do auto configure.
3. When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu).
OSD Lock Function: To lock the OSD, press and hold the MENU button
while the monitor is off and then press power button to turn the monitor on. To
unlock the OSD - press and hold the MENU button while the monitor is off
and then press power button to turn the monitor on.
NOTES
• Do not install the monitor in a location near heat sources such as radiators
•
•
or air ducts, or in a place subject to direct sunlight, or excessive dust or
mechanical vibration or shock.
Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
8
• To keep the monitor looking new, clean it with a soft cloth. Stubborn
•
stains may be removed with a cloth lightly dampened with a mild detergent
solution. Never use strong solvents such as thinner, benzene, or abrasive
cleaners, since these will damage the cabinet. As a safety precaution,
always unplug the monitor before cleaning it.
Do not scratch the screen with hard things, it may cause permanent
damage.
Don’t leak liquid into monitor which will result in the damage of component.
•
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press + or - to navigate through the functions. Once the desired function is
highlighted, press the MENU-button to activate it. If the function selected
has a sub-menu, press + or - again to navigate through the sub-menu
functions. Once the desired function is highlighted, press MENU-button to
activate it.
3. Press + or - to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5
The OSD Message
9
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Main
Sub Menu
Menu
Menu Item
Item
Icon
Sub
Menu
Brightness
Description
Backlight Adjustment
Contrast
Contrast from Digital-register.
Standard Standard Mode
Text
Luminance
Text Mode
Internet Internet Mode
Eco
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Off
Disable dynamic contrast ratio
On
Enable dynamic contrast ratio
DCR
Clock
Adjust picture Clock to reduce
Vertical-Line noise.
Phase
Adjust Picture Phase to reduce
Horizontal-Line noise
H.Position
Adjust the vertical position of the
picture.
V.Position
Adjust the horizontal position of the
picture.
Image Ratio
Enable monitor wide mode or 4:3 mode
Image
Setup
10
Color
Temp.
Warm
Recall Warm Color Temperature
from EEPROM.
Normal
Recall Normal Color Temperature
from EEPROM.
Cool
Recall Cool Color Temperature
from EEPROM.
sRGB
Recall SRGB Color Temperature
from EEPROM.
User-B Blue Gain from Digital-register
User
User-G Green Gain Digital-register.
User-R Red Gain from Digital-register
OSD
Setup
Extra
H.Position
Adjust the verticalposition of OSD
V.Position
Adjust the horizontal position of
OSD
Timeout
Adjust the OSD Timeout
Language
Select the OSD language
DDC/CI
Reset
Turn ON/OFF DDC/CI Support
yes or no Reset the menu to default
Show the information of the main
image and sub-image source
Information
11
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of its
identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The
host can request EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is similar
to a "Screen Saver" feature except the display is completely off. The display is
restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug
with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for
the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.
The other end terminates with a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
12
TECHNICAL SUPPORT (FAQ)
Problem & Question
Possible Solution
*Check if the Power Switch is in the ON
Power LED is not on
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
No Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Adjust the Contrast and Brightness
Picture is fuzzy
Controls.
Picture bounces or a wave
*Move electrical devices that may cause
pattern is present in the picture
electrical interference.
*Computer Power Switch should be in
the ON position.
*Computer Video Card should be snugly
seated in its slot.
*Make sure monitor’s video cable is
properly connected to the computer.
The power LED is ON (orange)
*Inspect monitor’s video cable and make
but there’s no video or no
sure none of the pins are bent.
picture.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS LOCK
key.
*Inspect the monitor’s video cable and
Missing one of the primary
make sure that none of the pins are
colors (RED, GREEN, or
bent.
BLUE)
Screen image is not centered or *Adjust pixel frequency (CLOCK) and
sized properly.
FOCUS or press hot-key (AUTO).
Picture has color defects
*Adjust RGB color or select color
(white does not look white)
temperature.
*When the brightness of the screen lowers
after being used for a certain period and
Poor brightness or contrast
the function of the display is affected,
send it to our authorized service center
for repair.
*Use win 95/98/2000/ME/XP shut-down
Horizontal or vertical
mode Adjust CLOCK and FOCUS or
disturbances on the screen
perform hot- key (AUTO-key).
13
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment
95/98/2000/ME/XP shut-down mode pattern.
use
“dot-pattern”
or
win
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1.
2.
Check that the signal-cable is properly connected, If the connector is
loose, tighten the connector’s screws.
Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode, set the computer to
display mode given in the following table.
14
APPENDIX
SPECIFICATIONS
LCD Panel
Input
Display Colors
Dot Clock
Max. Resolution
Plug & Play
Power Consumption
Driving system
Size
Pixel pitch
Video
Separate Sync.
H-Frequency
V-Frequency
ON Mode
OFF Mode
Input Connector
Input Video Signal
Power Source
Environmental
Considerations
Dimension
Weight (N. W.)
15
TFT Color LCD
470 mm(18.5")
0.3mm( H ) ×0.3mm ( V )
R,G,B Analog Interface
H/V TTL
31kHz – 83kHz
56-75Hz
16.7M Colors
84.75MHz
1366x768@60Hz
VESA DDC2BTM
≤25W
≤1W
D-Sub 15pin
Analog:0.7Vp-p(standard),
75 OHM, Positive
100~240VAC,50/60Hz
Operating Temp: 0° to 40°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 85%
445.4(W)X335.2(H)X161.06(D)
3.45kg
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Switch
External Controls:
Functions
Power Button
Menu
Image Ratio(+)
ECO/Source/Auto
Contrast
Brightness
Phase
Clock
H. Position
V. Position
OSD setup
Language
Information
(Warm)Color
(Cool)Color
sRGB
USER Color temperature
Reset
Exit
25Watts
FCC, UL
Power Consumption
( Maximum )
Regulatory Compliance
16
FACTORY PRESET TIMING TABLE
STANDARD
RESOLUTION
HORIZONTAL
FREQUENCY
(kHz)
VERTICAL
FREQUENCY
(Hz)
31.469
59.940
640×480 @60Hz
VGA
640×480 @75Hz
37.500
75.000
Dos-mode
720×400 @70Hz
31.469
70.087
800×600 @60Hz
37.879
60.317
800×600 @75Hz
46.875
75.000
1024×768 @60Hz
48.363
60.004
1024×768 @75Hz
60.023
75.029
1366x768@60Hz
47.852
59.964
SVGA
XGA
WXGA
CONNECTOR PIN ASSIGNMENT
1
5
6
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
1.
2.
3.
4.
5.
6.
7.
8.
DESCRIPTION
PIN NO.
DESCRIPTION
9.
10.
11.
12.
13.
14.
15.
+5V
Ground
Ground
DDC-Serial Data
H-Sync
V-Sync
DDC-Serial Clock
Red
Green
Blue
Ground
Detect Cable
R-Ground
G-Ground
B-Ground
17