- Computers & electronics
- TVs & monitors
- Monitors CRT
- Digital Networks North America
- PCXBV-Ux
- Installation Guide
Digital Networks North America PCXBV-Ux Installation guide
Add to my manuals17 Pages
Digital Networks North America PCXBV-Ux is a 17-inch, 15.7 viewable, multi-scanning color monitor with high resolution, compatible with VGA, SVGA, 1024 x 768, and 1280 x 1024 modes. The PCXBV-Ux offers the following features: • 1280 x 1024 non-interlaced mode. • Power Management system that exceeds EPA ENERGY STAR™ requirements for saving energy. • VESA Data Display Channel - DDC1/2b • Complies with Swedish MPR2 standards for low emissions* • Complies with Swedish TCO ’92 standards even lower emissions** • Anti-glare screen with anti-static coating
advertisement
TM
PCXBV-Ux Multi-Scanning
Color Monitor
Installation Guide
Order Number: ER − XBVUX − IM. A01
Digital Equipment Corporation
Maynard, Massachusetts
February 1996
The information in this document is subject to change without notice and should not be construed as a commitment by Digital Equipment Corporation.
Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and
Computer Software clause at DFARS 252.227-7013.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modification made to this equipment may void the user’s authority to operate this equipment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception; however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
•
Re-orient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
DO NOT attempt to modify this equipment. If modified, the FCC may void your authority to operate this equipment.
Canadian Department of Communications Statement
This Class B digital apparatus meets all requirements of the Canadian Interference
Causing Equipment Regulations.
DEC and the DIGITAL logo are trademarks of Digital Equipment Corporation. IBM is a registered trademark of International Business Machines Corporation. VESA is a registered trademark of the Video Electronics Standards Association. All other trademarks and registered trademarks are the property of their respective holders.
As an ENERGY STAR™ partner, Digital Equipment Corporation has determined that this product meets the ENERGY STAR™ guidelines for energy efficiency.
1996 Digital Equipment Corporation.
All Rights Reserved.
Contents
Introduction
Overview .................................................................................... 1
DDC (Display Data Channel) ................................................ 2
Installation
Installation/Operation Guidelines................................................ 2
Monitor Installation ..................................................................... 3
Servicing
Cleaning the Monitor .................................................................. 7
Maintenance and Troubleshooting ............................................. 7
Tilt/Swivel Stand Removal .......................................................... 9
Specifications
Scanning Modes......................................................................... 10
Monitor Specifications ................................................................ 11
Power Management System ...................................................... 12
Environment ............................................................................... 12
iii
Tables
Table 1 User Controls and Functions ........................................ 5
Table 2 User Controls Used With Arrow Buttons ....................... 6
Table 3 Identifying and Correcting Problems .............................. 8
Table 4 Display Modes and Addressability ................................ 10
Table 5 Monitor Specifications................................................... 11
Table 6 Power Saving States .................................................... 12
Figures
Figure 1 PCXBV-Ux Color Monitor ........................................... 1
Figure 2 PCXBV-Ux Monitor (Rear View) ................................. 3
Figure 3 Monitor Control Panel.................................................. 4
Figure 4 Monitor Controls .......................................................... 5
Figure 5 Tilt/Swivel Stand Removal ........................................... 9
Audience
This guide is intended for user’s who wish to install the monitor.
Conventions
The following conventions are used in this document:
Convention Meaning
Note
Caution
Provides general information.
Provides information to prevent damage to equipment.
Warning Provides information to prevent injury.
iv
Introduction
Overview
The PCXBV-Ux Monitor is a 17-inch, 15.7 viewable, multi-scanning color monitor with high resolution, compatible with VGA, SVGA, 1024 x 768, and
1280 x 1024 modes. The PCXBV-Ux offers the following features:
•
1280 x 1024 non-interlaced mode.
•
Power Management system that exceeds EPA ENERGY STAR™ requirements for saving energy.
•
VESA Data Display Channel - DDC1/2b
•
Complies with Swedish MPR2 standards for low emissions*
•
Complies with Swedish TCO ’92 standards even lower emissions**
•
Anti-glare screen with anti-static coating
Figure 1. PCXBV-Ux Color Monitor
DEC00800
*Models PCXBV-UA/UB/UC/UW/UX/UY.
**Models PCXBV-UD/UZ.
1
DDC (Display Data Channel)
DDC is a communication channel over which the monitor automatically informs the host system about its capabilities. DDC uses a formerly unconnected signal pin in the 15-pin VGA connector. The system will perform the “Plug ‘n Play” feature if both the monitor and the host implement DDC protocol.
Installation
Installation/Operating Guidelines
Observe the following basic rules for installation and use.
Do . . .
•
Use the power cord supplied with the monitor, which is UL-, CSA-, and VDE-approved.
•
Turn the monitor off when not being used for an extended period of time, or use Power Management if applicable.
Do Not . . .
•
Overload the ac outlet.
•
Move the monitor on a stand over carpet or thresholds.
•
Push objects into the monitor’s openings.
•
Add accessories that are not designed for this monitor.
•
Operate the monitor near water or in a damp environment, which could cause and electrical hazard.
•
Operate the monitor near magnets, motor devices, transformers, high power lines, or large steel pillars, which can cause distortion in the picture.
•
Obstruct the ventilation openings in the monitor’s cabinet, such as placing the monitor on a rug or within an enclosure.
•
Place the monitor near a radiator or heat source.
2
Monitor Installation
To connect your monitor:
1. Make sure the power to the monitor and the computer is off.
2. Connect the signal cable to the monitor then to the 15-pin interface connector on the High Resolution Graphic Video Adapter on the back of the computer.
3. Plug the ac power cord to the monitor, then to a properly-grounded ac electrical outlet.
D E C 0 0 80 1
Figure 2. PCXBV-Ux Monitor (Rear View)
3
Turn On Power to Monitor
Push the power switch button (3) to turn on the monitor. The power indicator
LED (2) should light green. For screen alignment, use the monitor controls (1).
4
1 2 3
D E C 0 0 80 2
Figure 3. Monitor Control Panel
Monitor Adjustments
Figure 4 shows the monitor adjustment controls. Some of the controls (1) have two functions. Press the button once or Function 1; press the button again for
Function 2. Tables 1 and 2 define these functions. The monitor saves your settings four seconds after your last adjustment.
1st/2nd
COLOR
TEMP
DEC00803
Figure 4. Monitor Controls
Table 1. User Controls and Functions
Icon Name Function
Brightness Adjusts black level for comfortable viewing.
▼
▲
Contrast
Decrease
Increase
Recall
Degauss
Adjusts white level for comfortable viewing.
Decreases value for the selected control.
Increases value for the selected control.
Recalls factory default settings. See Caution.
Clears picture impurity caused by moving the monitor to a new location. See Caution.
CAUTION: Pressing the Recall button, or pressing the
Degauss button for longer than 5 seconds, resets all of the data in the user memory area so you must remake your user adjustments.
5
Table 2. User Controls Used With Arrow Buttons
Icon Name With Function 1
Position (H/V) Adjusts horizontal position.
Position (H/V)
▼▲
Adjusts vertical position.
Function 2
Selects user or preset modes.
Pages through list of modes.
Size (H/V)
Size (H/V)
Geometric distortion
Geometric distortion
COLOR
TEMP.
Color temperature
▼▲
▼▲
▼▲
Adjusts horizontal size. Displays information on the specifications.
Adjusts vertical size.
Pages through list of specifications.
Pincushion: Adjusts the sides from bowing in or out.
Parallel: Adjusts the top and bottom to be parallel.
Tilt: Adjusts the tilt of the display.
Trapezoid: Adjusts the top and bottom to be the same.
Adjusts temperature between 9300
°
and
6500
°
K color.
–
6
Servicing
Cleaning the Monitor
To clean the monitor:
1. Unplug the monitor.
2. Clean the monitor with a soft, slightly damp cloth. Do not use an aerosol cleaner directly on the screen.
_____________________ CAUTION __________________________
Do not use benzene, thinner, or any volatile substance to clean the monitor, as these products may discolor the monitor’s cabinet. Likewise, do not place rubber or vinyl on the monitor.
Maintenance and Troubleshooting
Identifying and Correcting Problems
The following can be sources of problems:
•
Communications cables
•
Host system
•
Nearby power or electrical sources
7
Troubleshooting Table
Use Table 3 to identify and correct any problem area.
Table 3. Identifying and Correcting Problems
Symptom
Display does not appear.
Possible Cause
Brightness or contrast control is set too low.
Power Management feature is active in the off state.
There is no power.
Suggested Solution
Increase the brightness and contrast control setting to suit you.
Press any key and allow 20 seconds for monitor to warm up.
Check the power cord. Use another ac outlet.
Color impurity
Video display has moving dots and distorted lines.
The display rolls or flickers.
Magnetic fields can build up on the CRT.
There is electromagnetic interference.
Adjustments may be out of alignment.
Press the degauss switch to demagnetize the CRT. See
Caution below.
Move any electromagnetic device, such as a fan or motor, away from the monitor or move the monitor.
Hold the Recall button until the
LED changes from green to orange then back to green. See
Caution below.
CAUTION: Pressing the Recall button, or pressing the
Degauss button for longer than 5 seconds, resets all of the data in the user memory area so you must remake your user adjustments.
8
Tilt/Swivel Stand Removal
To remove the stand, remove the screw that secures the bottom of the stand and slide it back.
Figure 5. Tilt/Swivel Stand Removal
D E C 0 0 7 9 9
9
Specifications
Scanning Modes
Table 4 Display Modes and Addressability
Mode Display
Mode
1
2
VGA 60
DOS 70
3
4
5
6
7
Addressability
640 x 480
720 x 400
VGA/350 70 640 x 350
VGA
VESA 75
640 x 480
640 x 480 ErgoVGA
72
SVGA/60
SVGA
VESA 75
800 x 600
800 x 600
8
9
1024 x 768 1024 x 768
VESA 70 1024 x 768
10 1024 x 768
VESA 75
1024 x 768
11 1280 x 1024 1280 x 1024
Horizontal
Frequency
(KHz)
31.47
31.47
31.47
37.50
37.86
37.88
46.88
48.36
56.48
60.02
64.98
Vertical
Frequency
(Hz)
59.95
70.08
70.08
75.00
72.81
60.32
75.00
60.00
70.07
75.03
60.10
H
Sync
–
–
+
–
–
–
–
+
+
+
–
V
Sync
–
+
–
–
–
–
–
+
+
+
–
10
Monitor Specifications
Table 5 Monitor Specifications
Monitor
43 cm (17-inch, 15.7 maximum viewable) non-glare, non-static, multilayer optical coating
Active Area 32.0 x 24.0 cm (12.6 x 9.4 in)
Height 42.6 cm (16.8 in), includes tilt/swivel base
Width 43.4 cm (17.1 in)
Depth
Swivel
Tilt
44.4 cm (17.5 in)
±
45
°
-5
°
to +13
°
18 Kg (39.6 lb) Weight
Video Signal 0.7V p-p R, G, B color; separate Sync (positive or negative); 75
TTL
Horizontal
Scan Rate 30 - 65 kHz
Vertical Scan
Rate 50 - 120 Hz, non-interlaced
Connector 15-pin D-sub
Power input 100 - 240 Vac, 1.0 A. maximum, 50 - 60 Hz.
Environment
Operating
Temperature
Humidity
0
°
- 40
°
C
10 - 90% relative humidity (noncondensing)
11
Power Management System
The monitor has three power-saving states indicated by the LED on the front panel. A personal computer can control these states to reduce the monitor’s output power levels while not in use, thus saving energy.
For proper operation of this Power Management System, make sure that the monitor signal cable is connected to the host system and that the host is On.
Table 6 Power Saving States
LED
Green (Normal)
Amber
Alternating
Amber/Green
State
On
Standby
Suspend
Power Consumption
(Watts)*
110 (max)
< 75
< 15
Recovery
Time n/a
3 s
3 s
Alternating
Amber/Off
Off < 5 15 s
*These power-saving states exceed the Environmental Protection Agency (EPA) Energy Star requirements using the Video Electronics Standards Association (VESA) methodology for
Display Power Management Signals.
Environment
This monitor has been designed and manufactured to minimize the impact to the environment.
Acoustic Levels
Preliminary declared values per ISO 9296 and ISO 7779:
Sound Power Level 1
Idle
L
Wad
B
Operate
N/A 3.2
Sound Pressure
Level 2 L pAm
dBA
Idle Operate
N/A 25 PCXBV-Ux
1
1 B = 10 dBA
2
Operator position
12
Asbestos
This monitor does not use asbestos in any form.
Flame Retardants
The enclosures do not contain polybrominated diphenylether (PBDE) as a flame retardant additive; therefore, they do not emit toxic dibenzofuran and dibenzodioxin gases.
Ozone Depleting Substances (ODS)
These monitors are in full compliance with the labeling requirements in the
U.S. Clean Air Act Amendments of 1990. It does not contain, nor is it manufactured with, a Class 1 ODS, as defined in Title VI section 611 of this act.
PVC
The plastic enclosures are not made of rigid PVC. The material has a nonhalogenated, flame-retardant system and is cadmium free.
Recyclable Material
The packaging material can be recycled, or you can save it to return the monitor to a service center for repair or disposal.
Monitor Disposal
____________________ WARNING __________________________
If you need to dispose of a monitor, ask a qualified service representative for the proper procedure. Improper disposal could result in personal injury from implosion.
VCCI Class 2
13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Contents
- 5 Introduction
- 5 Overview
- 6 DDC (Display Data Channel)
- 6 Installation
- 6 Installation/Operating Guidelines
- 7 Monitor Installation
- 9 Monitor Adjustments
- 11 Servicing
- 11 Cleaning the Monitor
- 11 Maintenance and Troubleshooting
- 12 Troubleshooting Table
- 13 Tilt/Swivel Stand Removal
- 14 Specifications
- 14 Scanning Modes
- 15 Monitor Specifications
- 16 Power Management System
- 16 Environment