- Home
- Domestic appliances
- Large home appliances
- Dishwashers
- Electrolux
- EIDW5705PB
- Product information
Electrolux EIDW5705PB Wiring diagram
Add to my manuals2 Pages
Electrolux EIDW5705PB is a dishwasher with a variety of features to make dishwashing easier and more efficient. It has a 120-volt, 60Hz rating and requires a separate circuit with a 15-amp minimum and 20-amp maximum. The motor draws 1 amp, and the heater wattage ranges from 475 to 630 watts. The total amps (load rated) are 8.7. The TempAssure feature maintains a water temperature of 135°F ±5°F (60°C±3°C) with the outer door in place, and the TempBoost feature increases the temperature to 140°F ±5°F for heated wash and heated rinse cycles.
advertisement
▼
Scroll to page 2
Pump Assembly The pump assembly is driven by a synchronous motor. The motor drives a pump which supplies 100 percent filtered water Draining is accomplished by using a small separate synchronous drain pump mounted to the side of the sump. The drain pump is connected to the main pump by a small rubber hose. The drain check valve is located at the discharge end of the drain pump. The drain hose is attached by a clamp to the discharge end of the drain pump. Heater shut off electricity to dishwasher, remove outer door panel assembly, disconnect wiring to the actuator, remove the six screws, remove the dispenser, replace and reinstall screws, rewire actuator. Product Specifications Rating ................................... 120 Volts, 60Hz Separate Circuit..15 amp min.- 20 amp max. Motor (Amps) ...................................... 1 amp Heater Wattage .......................... 475 - 630W Total Amps (load rated) ........................... 8.7 TempAssure .............................. 135°F ±5°F (60°C±3°C) [with outer door in place] TempBoost ................................ 140°F ±5°F Heated Wash/Heated Rinse Hi-Limit Thermostat ............... 200°F (93°C) The drain hose must have a loop at a minimum Electrical height of 32 inches in order to insure proper drainage. • • • • • • • To replace dispenser: The water on the dishes is evaporated into drier air and the venting process continues. The heating element is turned ON and OFF during the entire drying cycle. Refer to the cycle chart on the reverse side to Voltage checks of the heater should be made in determine when the heater is on during the the dry portion of the service test mode. wash cycle. The heater cycles ON and OFF for brief periods during the drying cycle. Standard Dry Air Flow The heated, moist air leaving the dishwasher through the lower vent causes drier air to be drawn into the unit by way of intake vents located at the side of the tub. Detergent and Rinse Aid Dispenser The detergent and rinse aid dispenser is a one piece component consisting of a molded detergent cup and a built-in rinse aid dispenser. The detergent cup has a spring loaded cover and the rinse aid dispenser has a removable cover. Liquid rinse aid is added to the dispenser up to the fill line indicator. The amount of rinse aid released can be adjusted by turning the arrow indicator from one, being the least amount, to four, being the greatest amount. Water Supply Suggested minimum incoming water temperature ............................ 120°F (49°C) Pressure (PSI) min./max. ................... 20/120 Connection (NPT) ..................................... 3/8" Consumption (Normal Cycle) ....................... ............................................ 5.8-6.0 U.S. gal Water valve flow rate (U.S. GPM) ........... 0.9 Water recirculation rate (U.S. GPM) .............. ................................................. approx. 5.28 Water fill time ..................................... 43 sec. Trouble Shooting Tips Personal Injury Hazard Dishwasher runs but will not heat. Motor trips out on internal thermal overload protector. Motor hums but will not start or run. Dishwasher will not operate when turned on. Symptom 1. 2. 3. 4. 5. 1. 2. 3. 4. Drain restricted. Electronic control board defective. Defective drain pump. Blocked impeller. Open windings. Wiring or terminal defective. Latch mechanism defective. Electronic control board defective. Wiring or terminal defective. Broken spring(s). Defective actuator. Heater element (open). Electronic control board defective. Wiring or terminal defective. Hi-Limit thermostat defective. 1. Improper voltage. 2. Motor windings shorted. 3. Glass or foreign items in pump. 1. Motor (bad bearings). 2. Motor stuck due to prolonged non-use. 1. Fuse (blown or tripped). 2. 120 VAC supply wiring connection faulty. 3. Electronic control board defective. 4. No 12 VAC power to control. 5. Motor (inoperative). 6. Door switch (open contacts). 7. Door latch not making contact with door switch. 8. Touch pad circuit defective. 9. No indicator lamps illuminate when START or OPTIONS are pressed. Check the Following 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 1. 2. 3. 4. Clear restrictions. Replace control board. Replace pump. Check for blockage, clear. Replace pump assembly. Repair or replace. Replace dispenser. Replace control board. Repair or replace. Replace dispenser. Replace dispenser. Replace heater element. Replace control board. Repair or replace. Replace thermostat. 1. Check voltage. 2. Replace motor/impeller assembly. 3. Clean and clear blockage. 1. Replace motor assembly. 2. Rotate motor impeller. Always disconnect the dishwasher from the electrical power source before adjusting or replacing components. Detergent cover will not latch or open. 1. 2. 3. 4. 5. 6. 4. 5. 6. 7. Remedy Dishwasher will not pump out. 1. Water supply turned off. 2. Defective water inlet fill valve. 3. Check fill valve screen for obstructions. Defective float switch. Electronic control board defective. Wiring or terminal defective. Pressure Switch Stuck. Repair or replace. Replace control board. Repair or replace. Repair or replace. 1. Turn water supply on. 2. Replace water inlet fill valve. 3. Disassemble and clean screen. 8. Replace console assembly. 9. Replace console assembly. 3. 4. 5. 6. 7. 1. Replace fuse or reset breaker. 2. Repair or replace wire fasteners at dishwasher junction box. Replace control board. Replace control board. Replace motor/impeller assembly. Replace latch assembly. Replace latch assembly. Dishwasher will not fill with water. 4. 5. 6. 7. 1. Repair to proper 32-inch minimum height 2. Drain line connected to a floor drain not vented. 1. Drain hose (high) loop too low. Dishwasher water siphons out. Detergent left in dispenser. 1. Detergent allowed to stand too long in dispenser. 2. Dispenser wet when detergent was added. 3. Detergent cover held closed or blocked by large dishes. 4. Improper incoming water temperature to properly dissolve detergent. 5. See "Detergent cover will not open." 020905 SERVICE DATA SHEET P/N EIDW5705 Electronic Series This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products North America cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this Service Data Sheet. Color Code BK...................... Black BU........................ Blue PK.........................Pink RD..........................Red WH/RD.........White/Red RD-YE........Red/Yellow VT.......................Violet OR....................Orange GR......................Green W........................White To start Operation Press START/CANCEL pad. Close and latch door. Water/Service Test To delay start Press DELAY START pad to select desired delay time. Close and latch door. To select a new Press desired cycle and/or option pad. The indicator lights cycle or option will change. Press START/CANCEL within 15 seconds to begin cycle. To cancel cycle Press START/CANCEL. Dishwasher will drain for 60 seconds, then shut off. For controls lock . . . . . . . . . Press .. and hold the AIR DRY pad for 3 seconds. To unlock, press and hold the AIR DRY pad for 3 seconds. The water/service test is a Special function initiated from the power failure mode or idle mode. While in power failure or idle mode simultaneously press the AIR DRY and START/CANCEL pads for 1 1/2 seconds. The dishwasher will then step through the test cycle per the chart. Pushing the START/CANCEL pad will advance the dishwasher to the next step. Display Codes (Readout) LO..........Low liquid in the rinse aid dispenser PF..........A power failure has occurred Cd..........Close the door '01-24'....Hour(s) delay before start Cycle Selection Options Display Codes (LED) CLEAN ----------------- Shows completion of cycle. Indicator light will go off 30 seconds after door is opened. OPTION LED's Flashing -- HI-TEMP WASH and AIR DRY/ LED's flashing indicates power failure has occurred. Press START/CANCEL pad and reselect desired options and cycle. LOW RINSE ----------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is filled. (Some models) SANITIZE--------------- The SANITIZED criteria has been met. Indicator light will go off 30 seconds after door is opened. Wiring Diagram
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project