Electrolux ESL 4114 User's Manual

D i s h w a s h e r
Model ESL 4114
UK
Instruction book
1 03/03
Description of the appliance
1. Water hardness adjustment
2. Upper basket stop
3. Lower spray arm
4. Salt container
5. Detergent dispenser
6. Rinse aid dispenser
7. Control panel
8. Filters
9. Upper spray arm
10. Upper basket
11. Levelling spacers
IN99
1
3
2
4
1
STOP
The control panel
1. On/Off push button
3. Programme marker
2. Programme guide
4. Programme selector dial
2
Washing programmes
Programme
Degree of soil
and
type of load
Starting position
Required
of the programme push button
selector
Cycle
Recommended
quantity of detergent description
wash
prewash
1 65°
Heavy soil.
Crockery, cutlery, pots
and pans
1
On/Off
20 g
5g
Cold prewash
Main wash up to 65°C
1 cold rinse
1 hot rinse
Drying
2 65°
Normal soil.
Crockery and cutlery
2
On/Off
25 g
/
Main wash up to 65°C
1 cold rinse
1 hot rinse
Drying
**
Light soil.
Crockery and party
crockery
3
On/Off
25 g
/
Main wash up to 65°C
1 cold rinse
1 hot rinse
4
Any.
Partial load (to be
completed later in the
day).
4
On/Off
/
/
1 cold rinse (to avoid
food scraps from
sticking together).
*
3 65°
*
Testing programme for EN 50242 (see "Hints for Test Centres").
**
This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you
may re-use them promptly.
Technical specifications
Dimensions
Width
Height
Max depth
Max depth with open door
Electrical connection
Motor rating during wash
Power of heating element
Overall power
Voltage
Water supply pressure
Minimum
Maximum
44.6 cm
81.8 - 87.8 cm
55.5 cm
111.4 cm
220/240 V - 50 Hz
200 W
1900 W
2100 W
50 kPa (0.5 bar)
800 kPa (8 bar)
Capacity
8 place settings
3
Operating sequence
1. Check the filters
11. Switch off the dishwasher
Ensure they are clean and properly positioned (see
"Maintenance and cleaning"- Instruction book part 1).
Switch off the dishwasher by opening the
door and pressing the On/Off push button.
Wait a few minutes before removing the dishes; in this
way they will be cooler and the drying will be improved.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
2. Check that there is rinse aid and salt
3. Load the dishes
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
Remove any scraps of food.
Pull the lower basket out and arrange the saucepans,
plates and cutlery in it.
In general it is not advisable to open the door while the
machine is working; if the door is opened however, a
safety device ensures that the machine stops.
Pull the upper basket out and arrange the plates, saucers,
glasses and cups etc. in it.
Important!
Care must be taken if the door is opened during the hot
phase or immediately after a programme has finished, as
steam may escape.
Slide the baskets back into the machine.
4. Ensure that the spray arms can
rotate freely.
5. Measure out detergent
Add the required amount of detergent into the dispenser
according to the dosage quantity given in the "Washing
programmes" chart.
Close the detergent dispenser lid.
6. Set the programme
The selection of a programme occurs with the door
partially opened.
Turn the programme selector dial clockwise until the
number of the programme you wish to select corresponds
with the programme marker on the control panel.
9. Start the programme
Depress the On/Off push button and close the door, the
machine will start.
If you wish to interrupt the washing programme at any
time open the door and press this button again.
10. At the end of the washing
programme
At the end of the programme the dishwasher will
automatically stop.
4
Using your appliance
Loading your appliance
The upper basket
Before placing dishes in the machine, remove any scraps of
food, to avoid clogging the filters and consequently reducing
the performance.
Do not load very small items which can fall through the
baskets.
Open the door and slide out the baskets to load the dishes.
The upper basket is designed for plates (dessert plates,
saucers, dinner plates of up to 24 cm in diameter), salad
bowls, cups and glasses.
Arrange items on and
underneath the cup rack so
that water can reach all
surfaces.
Glasses with long stems can
be placed upside down in the
cup rack.
Light items (plastic bowls
etc.) should be loaded in the
upper basket and arranged
so they do not move.
US63
UI57
Before closing the door, ensure that the spray arms can
rotate freely.
UI12
The lower basket
The lower basket is designed to take saucepans, lids, plates,
salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the
edge of the basket, ensuring that the upper spray arm can turn
freely.
Adjusting the height of the upper basket
If washing very large plates (over 27 cm and up to 31 cm in
diameter) you can load them in the lower basket after moving
the upper basket to the higher position.
The cutlery basket
To move to the higher position proceed as follows:
Long bladed knives stored in an upright position are a
potential hazard.
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as
knives.
1. Move the front runner stops (A) of the upper basket
outward and slide the basket out.
2. Refit the basket in the higher position and replace the stops
(A) in their original position.
Cutlery should be placed in the removable cutlery basket with
the handles facing downwards.
If the handles protrude from the bottom of the basket,
obstructing the lower spray arm, load the cutlery with the
handles facing upwards.
Mix spoons with other cutlery
to prevent them from sticking
together.
Silver cutlery tends to go
black if mixed with steel
cutlery. Place it in the cutlery
basket separate from the
others.
RC01
When the top basket is in the higher position it will only
take plates up to 20 cm in diameter and you will not be
able to use the cup rack.
UI45
After loading your machine always close the door, as an
open door can be a hazard.
5
Hints for test centres
Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser.
Test standard
EN 50242
Reference programme:
Power Wash 65°C
Load:
8 standard place settings
Rinse aid selector:
position 4
Detergent dosage :
20 g in the dispenser
5 g on the dispenser lid
Arrangement upper basket
Arrangement lower basket
Arrangement
cutlery basket
6
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to
purchase spare parts please contact your local Service Force
Centre by telephoning:
Home visits are made between 8.30am and 5.30pm Monday to
Friday. Visits may be available outside these hours in which case a
premium will be charged.
08705 929929
Exclusions
Your telephone call will be automatically routed to the Service
Force centre covering your post code area.
This guarantee does not cover:
For the address of your local Service Force Centre and further
information about Service Force, please visit the website at
www.serviceforce.co.uk
●
Damage or calls resulting from transportation, improper use or
neglect, the replacement of any light bulbs or removable parts
of glass or plastic.
Before calling out an engineer, please ensure you read the details
under the heading Something not working.
●
Costs incurred for calls to put right an appliance which is
improperly installed or calls to appliances outside the United
Kingdom.
●
Appliances found to be in use within a commercial environment,
plus those which are subject to rental agreements.
●
Products of Electrolux manufacture which are not marketed by
Electrolux.
When you contact the Service Force Centre you will need to give
the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number (found on the rating plate)
5. The purchase date
European Guarantee
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
If you should move to another country within Europe then your
guarantee moves with you to your new home subject to the
following qualifications:
Customer Care
Department
For general enquiries concerning your Electrolux appliance or for
further information on Electrolux products please contact our
Customer Care Department by letter or telephone at the address
below or visit our website at www.electrolux.co.uk
Customer Care Department
Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 950950 (*)
Guarantee Conditions
Standard guarantee conditions
We, Electrolux, undertake that if within 12 months of the date of
purchase this Electrolux appliance or any part thereof is proved to
be defective by reason only of faulty workmanship or materials, we
will, at our option repair or replace the same FREE OF CHARGE
for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the
electricity supply stated on the rating plate.
●
The appliance has been used for normal domestic purposes
only, and in accordance with the manufacturer’s instructions.
●
The appliance has not been serviced, maintained repaired,
taken apart or tampered with by any person not authorised by
us.
●
All service work under this guarantee must be undertaken by a
Electrolux Service Force Centre.
●
Any appliance or defective part replaced shall become the
Company’s property.
●
This guarantee is in addition to your statutory and other legal
rights.
The guarantee starts from the date you first purchased your
product.
●
The guarantee is for the same period and to the same extent
for labour and parts as exists in the new country of use for this
brand or range of products.
●
This guarantee relates to you and cannot be transferred to
another user.
●
Your new home is within the European Community (EC) or
European free Trade Area.
●
The product is installed and used in accordance with our
instructions and is only used domestically, i.e. a normal
household.
●
The product is installed taking into account regulations in your
new country.
Before you move please contact your nearest Customer Care
centre, listed below, to give them details of your new home. They
will then ensure that the local service Organisation is aware of
your move and able to look after you and your appliances.
* calls to this number may be recorded for training purposes
●
●
7
France
Senlis
+33 (0) 3 44 62 20 13
Sweden
Stockholm
+46 (0) 20 78 77 50
Germany
Nurnberg
+49 (0) 800 234 7378
UK
Slough
+44 (0) 1753 219898
Italy
Pordenone
+39 (0) 800 117511
Ireland
Dublin
+353 (0) 14090753
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year
to a value of approx. 14 billion USD in more than 150 countries around the world.
152971 71/1
Subject to change without notice
© Electrolux plc 2003
Instruction Book
DISHWASHER
- Before use
- Maintenance
- Installation
Contents
Before use
Setting the water softener
Filling with salt
Filling with rinse aid and adjusting the dose
Use of detergent
2
2
2
3
3
External cleaning
Prolonged periods of non-operation
Frost precautions
Moving the machine
5
5
5
5
Something not working
6
Hints and tips
4
Maintenance and cleaning
Internal cleaning
Cleaning the filters
5
5
5
Installation
Water supply connections
Water outlet connection
Electrical connection
7
7
7
7
Important safety information
It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance
be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is
left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety
information.
This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the
appliance.
Installation
●
●
●
●
●
●
●
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt to
modify this product in any way.
Care must be taken to ensure that the appliance does not
stand on the electrical supply cable.
The appliance should not be connected to the electrical
supply by means of an extension cable.
Any electrical work required to install this appliance should
be carried out by a qualified electrician or competent
person.
Any plumbing work required to install this appliance should
be carried out by a qualified plumber or competent person.
●
●
●
●
●
●
●
Child Safety
●
●
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the controls
or play with the product.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children's reach.
Conservation
In the interest of the environment:
●
During Use
●
●
●
Long bladed knives stored in an upright position are a
potential hazard.
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
When finishing loading or unloading close the door, as an
open door can be a hazard.
Do not sit or stand on the open door.
Isolate the appliance from the power supply and turn off the
water supply after use.
Care should be taken when cleaning the bottom door seal
and hinge area as any exposed metal edges may cut if
care is not taken.
This product should be serviced by an authorised Service
engineer, and only genuine spare parts should be used.
Under no circumstances should you attempt to repair the
machine yourself. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning.
Contact your local Service Force Centre.
Always insist on genuine spare parts.
●
Items that are contaminated by petrol, paint, steel or iron
debris, corrosive, acidic or alkaline chemicals must not be
washed in this dishwasher.
Under no circumstances should you open the door whilst
the appliance is in operation. Always turn off the appliance
before opening the door.
Only use detergent specifically designed for use in
dishwashers.
●
●
1
Materials marked with the symbol
are recyclable.
Check with your local Council or Environmental Health
Office to see if there are facilities in your area for re-cycling
this appliance.
When the appliance is to be scrapped, cut off the power
supply cable and make the door closing device unusable to
prevent young children from being trapped inside.
Help to keep your country tidy - use authorised disposal
sites for your old appliance.
Before use
Adjustment on the machine
Before using your dishwasher for the
first time:
A
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with salt
5. Fill the rinse aid dispenser.
A
1 2
AA04
Setting the water softener
Attention!
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting a washing
programme. This will prevent any grains of salt or salty
water, which may have been spilled, remaining on the
bottom of the machine, which may cause corrosion.
To fill:
1. To fill with salt, unscrew the cap of the salt container.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel (if
provided), pour in the salt
until the container is full.
Do not worry if water over
flows from the unit when
filling with salt, this is quite
normal.
Only for dishwasher models with salt refill
indicator light:
if the water softener has been adjusted on level 1 without use
of salt, the salt refill indicator light on the control panel will
always remain illuminated when the machine is switched on.
To adjust the water softener, follow the instructions given
in the chart
Use
of
salt
0 - 140
Adjustment
Water
on the machine
softener
adjustment
A*
B
1
0 - 14
NO
-
NO
1
2
15 - 39 11 - 27 141 - 390 YES
-
NO
1
3
40 - 50 28 - 35 391 - 500 YES
+
NO
1
4
51 - 70 36 - 49 501 - 700 YES
-
YES
2
5
71 - 90 50 - 63 701 - 900 YES
+
YES
2
0 - 10
* If your appliance is type A
LE
SA UT
ZO LT
SA LZ
SA L
SE
4. Replace the cap making
sure that there is no trace
of salt on the screw thread
or on the gasket.
Water hardness
PPM
(parts per
million)
AA03
Filling with salt
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, Clarke,
French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The dishwasher is factory set at level 2.
If this level is not suitable for your area the softener should be
adjusted.
If your water is level 1 it is already soft and therefore
there is no need to use salt.
In this case adjust the water softener on level 1 without
using salt.
French Clarke
Level
degrees degrees
(°TH)
B
SR14
5. Screw on the cap tightly.
The salt container will require topping up periodically.
According to the model, an indicator reminds you when filling
with salt:
A) The salt cap has a refill
indicator window in the
centre.
A green float is clearly
visible when there is salt
inside the container, and
almost disappears when
the salt has finished
reminding you to add salt.
Water softener adjustment
and adjustment is
necessary, YES in the
water softener chart
indicates that the
membrane must be pierced
as shown.
SR11
B) A salt indicator light on the
control panel will come on
when the salt has finished.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer.
The function of the machine is not affected.
AA01
2
Rinse aid
Use of detergent
Rinse aid is automatically added during the last rinse,
ensuring thorough rinsing, and spot and streak free drying.
The dispenser, which is positioned inside the door, holds
about 110 ml of rinse aid, which is sufficient for 16 - 40
dishwashing programmes, depending upon the dosage
setting.
Only use detergents specifically designed for use in
dishwashers.
We recommend the use of Finish detergents which are
available in the following options:
Finish Double Action Tablets. Each tablet has the exact
amount of detergent required, simply place in the dispenser.
Finish Powder recommended for every day use.
Finish Liquid Gel ideal for every day use. As the gel is extra
gentle is it recommended for fine bone china.
Filling with rinse aid
1. Open the container by turning the lid (A) anticlockwise.
If using powder detergents proceed as follows:
2. Add the rinse aid until the container is completely full.
The indicator (B) will be completely dark.
1. Open the dispenser lid by pulling the catch (D).
2. Add the detergent according to the recommended
quantity given in the "Washing programmes" chart
(see "Instruction Book - Part 2").
As all detergents are not the same, you should also
consult the instructions on the packet.
3. Always close the lid.
BR01
4. If the programme has a prewash add a little amount of
detergent over the lid of the dispenser. Follow the
recommended quantity given in the "Washing
programmes" chart (see "Instruction Book - Part 2").
BR03
3. Top up the rinse aid when the indicator (B) becomes
clear.
(Only for models with rinse aid indicator light)
Top up with rinse aid when the rinse aid indicator light on
the control panel illuminates.
Ensure that the lid is closed after every refill.
Do not put liquid detergent in the rinse aid compartment.
Clean up any rinse aid spilt during filling with an absorbent
cloth to avoid excess foaming during the next wash.
DE17
DE02
If using detergent in tablets proceed as
follows:
Adjusting the dose
1. For all programmes; place 1 tablet inside the detergent
dispenser.
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (C)
(position 1 minimum dosage, position 6 maximum dosage).
2. Always close the lid.
3. For all programmes with prewash; place a portion of a
further tablet on the lid of the detergent dispenser.
Increase the dose if there are drops of water or lime spots on
the dishes after washing.
If your dishwasher has a SID dispenser and you require a
prewash, put the extra detergent into the SID dispenser
and not on the lid of the detergent dispenser.
Reduce it if there are sticky whitish streaks on the dishes.
Insufficient quantities of detergent will produce poor
washing results, whereas an excessive amount of
detergent will not improve washing results and is also
wasteful.
Using no more than the correct amount also contributes
to reducing pollution.
Compact detergents with enzymes
BR02
In these compact powders the environmentally unfriendly
components have been replaced by natural enzymes and
other more biodegradable substances.
The enzymes deploy their full dirt dissolving power at a
temperature as low as 50°C.
By choosing the 50°C programmes (if available) you can
therefore achieve the same cleaning results that would
otherwise be achievable only with 65°C programmes and
conventional detergents.These new compact powders are
generally phosphate-free.
3
Hints and tips
To save energy
Place dishes in the machine immediately after every meal and
wait until the dishwasher is full before washing.
If necessary run the Rinse and Hold programme (see
"Washing Programmes" chart) so that any food scraps do not
become caked on the dishes while you are waiting to run the
complete wash programme.
Do not prewash dishes under running water.
For best washing and drying results
Before loading, remove all scraps of food and soak very
heavily soiled pots and pans.
Arrange saucepans, cups and glasses etc. upside-down.
Tilt items with convex or concave surfaces so that the water
drains off easily.
Avoid contact between the dishes as far as possible.
Items not suitable for dishwashers
The following items should not be washed in the
dishwasher (unless they are sold as dishwasher proof):
- Cutlery with wooden or horn handles or glued parts
- bronze cutlery
- saucepans with wooden handles
- aluminium ware
- crystal ware
- leaded glass
- plastic items
- antique or fine decorated china
Certain types of decoration can discolour when washed in a
dishwasher.
Crystal-ware and plastic objects, if not guaranteed dishwasher
proof should be washed by hand.
Certain types of glass can also become opaque after being
washed several times in a dishwasher.
A chemical reaction can occur between silver cutlery and
stainless steel cutlery. As a precaution, do not wash together.
Iron and cast iron objects can rust and stain other items.
Aluminium tends to go black, copper, pewter and brass tend to
stain.
If in doubt check with manufacturer of the item.
When buying new dishes, ensure that they are
dishwasher proof.
For best results we recommend the use of Finish detergents, rinse aid and salt.
EASY
POURING
PACK
N EW
TION
DOUBLE AC
FOR A
BRILLIANT
SHINE
L I Q U I D
G E L
P O W D E R
RINSE
C O N C E N T R AT E D D I S H WA S H E R D E T E R G E N T
DE15
4
Maintenance and cleaning
Internal cleaning
External cleaning
Ensure that the seals around the door, the detergent and rinse
aid dispensers are cleaned regularly with a damp cloth.
We recommend the use of Finish Dishwasher Cleaner every
3 months or run a 65°C wash without dishes using detergent.
Regular use of Finish Dishwasher Cleaner cleans
inaccessible parts, eliminates unpleasant food odours and
helps prevent the build-up of limescale.
Clean the external surfaces of the machine and control panel
with a damp soft cloth. If necessary use only neutral
detergents. Never use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
Cleaning the central filter
If you are not using the machine for any period of time you are
advised to:
Prolonged periods of non-operation
(After each wash)
1. Unplug the appliance and then turn off the water.
Inspect the central filters (B) and (C) and remove any scraps
of food with a brush, under running water.
2. Fill the rinse aid dispenser.
3. Leave the door ajar to prevent the formation of any
unpleasant smells.
Filters (B) and (C) are both removed by lifting up the outer one
(B) (pulling the central funnel upwards); the smaller filter (C)
can be removed by pressing the two tongues (D).
4. Leave the inside of the machine clean.
Frost precautions
D
C
D
Avoid placing the machine in a location where the temperature
is below 0°C. If this is unavoidable, empty the machine, close
the appliance door, disconnect the water inlet pipe and empty
it.
B
B
MA02
C
MA13
Once cleaned, refit the filters by
pressing them down until they
click into place.
Moving the machine
If you have to move the machine (moving house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
MA08
Avoid over tilting the machine during transportation.
Cleaning the large filter
(Every week)
Clean the large filter (A) on both sides under running water,
using a brush.
To take it out, remove the spray arm by pressing the two
tongues (E), turn the ring (F) anticlockwise and then slide the
whole part out. Refit the filter following the above instructions
in reverse order.
E
E
A
F
MA03
A
F
MA01
The dishwasher must not be used without filters.
Incorrect repositioning and fitting of the filters will
produce poor washing results.
Cleaning the filters is vital to ensure correct operation of
the machine.
5
Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer.
Before contacting your local Service Force Centre, please carry out the checks listed below.
Important:
If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a
charge will be made even if the appliance is in guarantee.
Symptom
Solution
The machine will not start
●
●
●
The machine does not fill with water
The door has not been properly closed.
The plug is not properly inserted in the power socket.
There is a power failure.
●
Ensure the water tap is open.
Ensure the mains water supply has not been cut off.
The inlet hose may be squashed or bent. Reposition the hose.
The inlet hose may be blocked. Switch off the water supply and clean the filter.
The filters are blocked
●
Clean the filters (refer to "Maintenance and cleaning").
The spray arms are not rotating
●
Ensure the crockery is loaded correctly.
The dishwasher will not drain
●
The drain hose may be squashed or bent. Reposition the hose.
The sink may be blocked. Clear any blockages.
The drain hose extension is not correct. Follow the instructions for connecting
to the waste.
There is no vent in the end of the drain hose.
●
●
●
●
●
●
The machine is noisy
●
Dishes are rattling against each other, refer to “Loading your machine”.
The spray arms are knocking against the dishes. Refer to "Loading your
machine".
The door is difficult to close
●
The dishwasher is not level, or not properly built-in.
Visible lime deposits or white film
on the dishes
●
●
Check that there is salt and that the salt cap is tight.
Check that the right level of the water softener is set.
The dishes are not quite dry
●
The rinse aid has run out or too little is being used.
The dishes are not clean (poor wash)
●
The baskets are too full.
The dishes have not been arranged properly.
The spray arms do not rotate
The spray arms are clogged.
The filters are clogged.
The filters are not in the correct position.
Not enough detergent has been used or it is unsuitable.
The detergent is old or has gone hard.
The salt container cap is not properly closed.
The washing programme selected is too gentle.
●
●
●
●
●
●
●
●
●
●
If after all these checks, the problem persists, contact your
local Service Force Centre, quoting the model and serial
number. This information can be found on the rating plate
located on the right hand side of the dishwasher door.
This product should be serviced by an authorised Service
engineer, and only genuine spare parts should be used.
Under no circumstances should you attempt to repair the
machine yourself.
Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local
Service Force Centre.
Always insist on genuine spare parts.
Prod.No. ........ Ser. No. .........
Mod. ........
RA01
6
Installation
Any electrical work required to install this appliance should
be carried out by a qualified electrician or competent
person.
Any plumbing work required to install this appliance should
be carried out by a qualified plumber or competent person.
Remove all packaging before positioning the machine.
If possible, position the machine next to a water tap and a drain.
+ 2 m max
Good levelling is essential for correct closure and sealing of the
door. When the appliance is correctly levelled, the door will not
catch on the levelling spacers on either side of the cabinet. If the
door does not close correctly, loosen or tighten the adjustable
feet until the machine is perfectly level.
CS10
Attention!
Our appliances are supplied with a with a security device to
protect against the return of dirty water back into the
machine.
If the spigot of your sink has a "no return valve"
incorporated this can prevent the correct draining of your
dishwasher. We advise you therefore to remove it.
Water supply connections
This dishwasher must be plumbed into a cold water supply.
The water pressure must be within the limits given in the
"Technical specifications" (Instruction Book - Part 2).
Your local Water Authority will advise you on the average mains
pressure in your area.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation.
Do not use, for connection, old hoses which have been
used in another appliance.
The locknut must be correctly fitted to avoid water leaks.
Avoid bends or kinks in the hose which could prevent or slow
down the water supply.
If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a few
minutes before connecting the inlet hose. This will prevent
deposits of sand or rust clogging the inlet hose.
Electrical connection
This appliance must be earthed.
The manufacturer declines any responsibility should this
safety measure not be observed.
The appliance should not be connected to the electrical
supply by means of an extension cable.
If the plug that is fitted to your appliance is not suitable for the
socket, it must be cut off and the appropriate plug fitted.
Important
The wires on the mains lead are coloured in accordance with the
following code:
Green and Yellow
Blue
Brown
Water outlet hose connection
The end of the drain hose can be connected in the following
ways:
1. To the sink outlet spigot, securing it to the underside of the
work surface. This will prevent waste water from the sink
running into the machine.
2. Hooked over the edge of the sink using the special
curved plastic guide (if provided).
3. To a stand pipe provided with vent-hole, minimum
internal diameter 4 cm.
2
If you fit your own plug,
the colours of the wires
in the mains lead of
your appliance may not
correspond with the
markings identifying the
terminals in your plug.
18
13 A
E
N
L
CE04
Ø
Ø
- Earth
- Neutral
- Live
min 4 cm
3
21
1
min 30 cm
max 100 cm
Levelling
max 100 cm
Ø 18
Ø 21
The sink plug must not be in place when the machine is draining
as this could cause the water to siphon back into the machine.
1. Connect the Green and Yellow (earth) wire to the terminal
in the plug which is marked with the letter "E" or the earth
min 30 cm
max 100 cm
max 100 cm
Proceed as follows:
symbol
or coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the plug
which is marked with the letter "L" or coloured red.
The plug moulded onto the lead incorporates a 13amp BSI362
fuse. Only ASTA or BSI fuses should be used.
The plug must not be used if the fuse cover/carrier is lost. The
cover/carrier is indicated by the coloured insert at the base of the
plug.
A replacement cover/carrier must be obtained from your local
Service Force Centre.
CS09
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.
The drain hose can face either to the right or left of the
dishwasher
Ensure the hose is not bent or squashed as this could prevent or
slow down the discharge of water.
If you use a drain hose extension it must be no longer than 2
metres and its internal diameter must be no smaller than the
diameter of the hose provided.
Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided.
7
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
152981 73/2
Subject to change without notice
2 03/03