FAVORIT 88080 i
Dishwasher
User information
Dear customer,
Please read this User Information carefully and keep it to refer to at a
later date.
Pass this User Information on to any subsequent owner of the appliance.
1
3
2
2
The following symbols are used in the text:
Safety instructions
Warning: Notes that concern your personal safety.
Attention: Notes that show how to avoid damage to the appliance.
Useful tips and hints
Environmental information
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Diagram of appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Switching on for the first time – setting the language . . . . . . . . . . . . .
8
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Basic operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
An overview of the menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting an option/setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Prior to using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding special salt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filling up with rinse aid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the acoustic signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
14
15
16
In daily use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading cutlery and dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the height of the upper basket. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using 3in1 detergents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the dishwashing cycle (Cycle Table) . . . . . . . . . . . . . . . . . . . . . . . .
Starting a dishwashing cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching off the dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
23
24
26
28
31
33
34
Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remedying small malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If the dishwashing results are not satisfactory. . . . . . . . . . . . . . . . . . . . . . . .
38
38
38
41
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Notes for Test Institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3
Installation and connection instructions. . . . . . . . . . . . . . . . .
46
Safety information for the installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Installing the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Guarantee Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
Customer Service Centres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
Service
4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Operating Instructions
1 Safety
Prior to using for the first time
• Follow the ”Instructions for installation and connection”.
Correct use
• The dishwasher is only intended for washing domestic dishes.
• Additions or modifications to the dishwasher are not permitted.
• Use only special salt, detergent and rinse aid suitable for domestic
dishwashers.
• Do not put any solvents in the dishwasher. This could cause an explosion.
Child safety
• Keep packaging away from children. There is a risk of suffocation.
• Children often do not recognise the hazards associated with electrical
appliances. Don’t allow children to use the dishwasher unsupervised.
• Make sure that children and pets don’t climb into the dishwasher.
Could endanger life!
• Dishwasher detergents can cause chemical burns to the eyes, mouth
and throat. Could endanger life! Comply with the safety instructions
of the dishwasher detergent manufacturer.
• The water in the dishwasher is not for drinking. Risk of chemical
burns.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play
with the appliance.
• Warning: Dishwasher detergents are strongly alkaline. They can be
extremely dangerous if swallowed. Avoid contact with skin and eyes
and keep children away from the dishwasher when the door is open.
Check that the detergent recatacle is empty after completion of the
wash cycle.
5
General safety
• Repairs to the dishwasher are only to be carried out by qualified service engineers.
• When the dishwasher is not being used, switch it off and shut off the
water tap.
• Never unplug the appliance by pulling on the cable. Always pull the
plug.
• Ensure that the door of the dishwasher is always closed when it is not
being loaded or unloaded. In this way you will avoid anybody tripping
over the open door and hurting themselves.
• Never sit or stand on the open door.
• If the dishwasher is located in a room where there may be a frost, remove the connection hose from the tap after each use of the dishwasher.
6
Diagram of appliance
Top Spray Nozzle
Upper basket spray arm
and floor spray arm
Water hardness
dial
Dispenser
for special salt
Dispenser
for detergent
Dispenser
for rinse aid
Rating plate
Filters
Interior lighting
Control panel
ON/OFF button
Direction buttons
OPTION
button
Display
Button
OK/START
RESET
button
7
Button functions
ON/OFF
Direction
buttons
OPTION
RESET
OK/START
– Switching the appliance on and off
– Selecting within the menu
– Selecting a value when adjusting options or settings
– Changing between Programmes menu and Options menu
– while a dishwashing cycle is running: briefly changing the display’s
text line from displaying the cycle stage to displaying the dishwashing cycle
–
–
–
–
cancelling the cycle that is running
with options and settings: cancelling the setting procedure
changing from Options menu to Programmes menu
changing from Settings sub-menu to Options menu
– in the Programmes menu: starting a selected programme
– changing from SETTINGS… (Options menu) to Settings sub-menu
– in the Options menu: starting and finishing the setting procedure
Switching on for the first time – setting the
language
1. Press the ON/OFF button.
First of all HELLO appears in the display.
As soon as the dishwasher is ready
for use, this is replaced by LANGUAGE ENGLISH; the word ENGLISH is
flashing.
2. Using the direction buttons ( or
) select the desired language.
3
3
3. Press the OK/START button.
This will have changed the display to
the desired language. CHOOSE PROGRAMME is shown in the display.
If you want to change the language at a later time, please see the section “Resetting the language”.
You can adjust the display lighting, by changing the settings BRIGHTNESS and CONTRAST1; see section “Basic operation”.
1. not available with all models
8
Display
Info status bar
Text line
Symbol line
The info status bar consists of a row of individual lamps that is divided
into two sections: the left section refers to the Programmes menu, the
right section to the Options menu.
• In the Programmes and Options menus you can see at what stage
within a cycle you currently are (the relevant lamp flashes).
• While a dishwashing cycle is running, the info status bar functions as
a programme progress display. You can then see at any time how
many programme stages are still to take place (including the current
programme stage).
The text line indicates in the Programmes menu the name of the programme selected and the estimated length of the cycle in minutes.
• In the Options menu the name of the selected option or setting is displayed and the current value set.
• While a dishwashing cycle is running, in the text line you can see the
name of the current programme stage and the estimated time remaining for the whole dishwashing cycle.
Using the OPTION button you can briefly display the name of the
dishwashing cycle.
• If there is a fault, a message is displayed.
The symbols in the symbol line have the following meanings:
– Option DELAY START active
– Programme selected for the hygienic cleaning of e.g. babies’ bottles
– Option 3 IN 1 active
– Loudspeaker is switched off; no acoustic signals (SOUND VOLUME setting)
9
Basic operation
This section contains basic information regarding the use of your dishwasher. Please read this section very carefully.
An overview of the menus
Programmes menu
Options menu
DELAY START
AUTOMATIC
30 MINUTES
OPTION
button
3 IN 1
70° INTENSIVE
SETTINGS…
65° NORMAL
OK/START
button
ENERGY
50° NORMAL
45° GLASS
LANGUAGE
WATER HARDNESS
RINSE AID
PREWASH
SOUND VOLUME
BRIGHTNESS
CONTRAST1
1. not available with all models
The Programmes menu
• After switching on the dishwasher you will find yourself in the Programmes menu.
• Select your dishwashing cycle here using the direction buttons ( or
). In the info status bar your position within the menu is always
shown.
• Change to the Options menu using the OPTION button.
The Options menu
• Here go to the desired setting using the direction buttons ( or ).
In the info status bar your position within the menu is always shown.
• For the option DELAY START see the section “Setting a delay start” for
the option 3 IN 1 see the section “Before using for the first time”
10
• Use the OK/START button to switch from the menu item SETTINGS…
to the Settings sub-menu.
The Settings sub-menu
Here go to the desired setting using the direction buttons ( or ). In
the info status bar your position within the sub-menu is always shown.
• LANGUAGE
To set the language of the text line in the display; also see the section
“Resetting the language”.
• WATER HARDNESS
To set the value for water hardness electronically (value range 1 to
10).
• RINSE AID
When option 3 IN 1 is activated: Switch rinse-aid addition function
on or off.
When option 3 IN 1 is not activated: The rinse-aid addition function
is always switched on, even if OFF is selected for RINSE-AID.
• SOUND VOLUME
To set the sound volume of the acoustic signals (value range 0 to 5);
at 0 the acoustic signals are switched off.
• BRIGHTNESS
To set the brightness of the display (value range 1 to 10).
• CONTRAST1
To set the contrast of the display (value range 1 to 10).
Adjusting an option/setting
3
3
1. Go to the option or setting that you wish to adjust.
2. Press the OK/START button. The value that is currently set will flash.
3. Using the direction buttons ( or ) select the desired value.
4. Press the OK/START button. The newly set value is lit without flashing.
5. Using the direction buttons ( or ) you can select another option or
setting.
A selected value is accepted using the OPTION button. In the display
the first entry in either the Options or Settings menu is displayed.
You can abort the setting procedure using the RESET button.
1. not available with all models
11
Prior to using for the first time
3
If you wish to use 3 in 1 detergent:
– First read the section “Using 3in1 detergents”.
– Do not fill up with special salt or rinse aid.
If you do not use 3in1 detergent, before using for the first time
1. Set the water softener
2. Fill up with special salt for water softeners
3. Fill up with rinse aid
Setting the water softener
3
The water softener must be set manually and electronically:
To avoid scale deposits on the dishes and in the dishwasher, the dishes
must be washed with soft water, i.e. water with a low lime content. The
water softener must be set according to the table to the water hardness in the area where you live. Your local water company will be able
to give you information about the water hardness in your area.
The dishwasher must be switched
off.
Setting manually:
1. Open the dishwasher door.
2. Remove the lower basket from the
dishwasher.
3. Turn water hardness dial on the left
wall of the dishwasher interior to O
or 1 (see table).
12
3
Setting electronically:
1. Press the ON/OFF button.
If the name of a programme stage is displayed in the display, a dishwashing cycle is active. First of all you must abort the dishwashing cycle:
– Press the RESET button. CONFIRM CANCEL? appears in the display.
– Press the OK/START button. This cancels the dishwashing cycle.
2. Go to the WATER HARDNESS setting; see section “Adapting an option/
setting”.
3. Set WATER HARDNESS to the right setting.
If the water softener is set electronically to “1” this switches off the
display of the REFILL SALT message.
Water hardness
Adjusting the hardness setting
in °d1)
in mmol/l2)
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
IV
19 - 22
15 - 18
3,3 - 3,9
2,6 - 3,2
III
11 - 14
1,9 - 2,5
II
4 - 10
0,7 - 1,8
I/II
2
below 4
below 0.7
I
1
no salt necessary
Range
Manual
Electronic
1
103)
9
8
7
6
5
4*
3
0*
1) (°d) German degree, measure of the hardness of water
2) [mmol/l] millimol per litre, international unit for water hardness
3) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting
13
Adding special salt
3
3
14
To decalcify the water softener, it must be filled up with special salt.
Use only special salt suitable for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with special salt:
– Before using the dishwasher for the first time.
– If when starting a cycle the message REFILL SALT is displayed.
1. Open the door and remove the lower basket.
2. Screw open the lid on the salt dispenser by turning it anti-clockwise.
3. Only when using the dishwasher
for the first time:
Fill the salt dispenser with water.
4. Place the funnel (supplied) over the
dispenser opening.
Fill the dispenser with special salt;
the capacity of the dispenser is approx. 1.0-1.5 kg, depending on the
size of the grains. Do not overfill the
dispenser.
If water overflows when filling up with special salt, this is completely
harmless.
5. Clean away any salt remnants from the dispenser opening.
6. Screw the lid back on in a clockwise direction.
7. Run a dishwashing cycle after filling the salt dispenser with special
salt. This will wash away salt water and salt crystals that have been
spilt.
Depending on the size of the grains, it can take several hours for the
salt to dissolve in the water and for the message REFILL SALT not to be
displayed when starting a dishwashing cycle.
Filling up with rinse aid
With rinse aid the rinsing water drains away better and so you get
smear-free, gleaming dishes and clear glasses.
If you do not use 3in1 detergent, fill up with rinse aid:
– Before using the dishwasher for the first time.
– If when starting a dishwashing cycle the message REFILL RINSE AID is
displayed.
Use only special rinse aid for dishwashers and no other liquid detergents.
1. Open the door.
The rinse aid compartment is located on the inside of the dishwasher
door.
2. Press the release button on the rinse
aid compartment.
3. Open the cover.
4. Pour rinse aid in slowly right up to
the broken “max” line;
this corresponds to a volume of approx. 140 ml when full.
5. Press the lid shut until it clicks into
place.
6. Wipe up any spilt rinse aid with a
cloth. Otherwise there will be too
much foam when rinsing.
15
Setting the amount of rinse aid required
3
Only change the amount dispensed, if smears, milky spots (reduce the
amount) or dried on water spots (increase the amount) can be seen on
glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in
the factory.
1. Open the dishwasher door.
2. Press the release button on the rinse
aid compartment.
3. Open the cover.
4. Set the dosage level.
5. Press the lid shut until it clicks into
place.
6. If rinse aid has leaked out, wipe it
away with a cloth.
Setting the acoustic signal
3
16
In addition to the optical display (e.g. indicating the end of the cycle,
errors) you can also choose to set an acoustic signal.
1. Press the ON/OFF button.
If the name of a programme stage is displayed in the display, a dishwashing cycle is active. First of all you must abort the dishwashing cycle:
– Press the RESET button. CONFIRM CANCEL? appears in the display.
– Press the OK/START button. This cancels the dishwashing cycle.
2. Go to the SOUND VOLUME setting; see the section “Adapting an option/setting”.
3. Set the value for the sound volume.
You can set a value from 0 to 5. At 5 the acoustic signals are very loud,
at 0 no acoustic signals are emitted; in addition the symbol
is lit in
the display.
In daily use
Loading cutlery and dishes
1
Sponges, cleaning cloths and any other objects that can absorb water
must not be washed in the dishwasher. Plastic and Teflon-coated dishes
and pans tend to retain water droplets. These dishes and pans therefore
do not dry as well as those made of china and stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn,
china or mother of pearl handles
• Plastic items that are not heat
resistant
• Older cutlery with cement
that is sensitive to temperature
• Dishes or cutlery with glued
parts
• Pewter or copper items
• Lead crystal glass
• Steel items that rust
• Wooden boards/platters
• Items made from synthetic materials
• Only wash stoneware in the dishwasher if it is
specifically marked by the manufacturer as
being dishwasher-safe.
• Glazed patterns may fade if washed very frequently in the dishwasher.
• Silver and aluminium parts have a tendency to
discolour during washing. Food remains, e.g.
egg white, egg yolk and mustard often cause
discoloration and staining on silver. Therefore
always clean food residues from silver immediately, if it is not to be washed straight after
use.
• Glass can become dull after a large number of
washes.
• Before loading the dishes, you should:
– Remove the worst of the food residues.
– Soak pans with burnt-on food residues.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation of the spray arms.
– Load bowls, cups, glasses, pans, etc. with the opening downwards so
that water cannot collect in them
– Dishes and items of cutlery must not lie inside one another or cover
one another
– To avoid damage to glasses, they must not touch one another
– Don’t put small items (e.g. lids) in the baskets for the dishes, but in
the cutlery basket, so that they can’t fall through the holes.
17
Loading cutlery
1
Warning: Sharp knives and other items of cutlery with sharp edges
must be laid in the cutlery rack or in the upper basket to avoid the risk
of injury.
To ensure that all items of cutlery in the cutlery basket can be reached
by the water, you should:
1.Place the grid insert on the cut- 2.Place forks and spoons in the
lery basket
cutlery basket's grid insert with
their handles pointing downwards.
For larger utensils, such as whisks, leave off one half of the cutlery grid.
The cutlery basket can be opened
out.
Always make sure that you put your
hand around both parts of the twopart handle when removing it from
the dishwasher.
1. Place the cutlery basket on a table
or work surface.
2. Open out the two-part handle.
3. Remove cutlery.
18
Loading / Unloading lower basket and upper basket
To load and unload, pull out or push
in the upper and lower baskets in
the middle using the handle on the
front of the basket.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes
and pans in the lower basket.
(Max. diameter for plates 29 cm).
To make it easier to load larger dishes, all rear plate rests in the lower
basket can be folded down.
19
Beer glasses and champagne glasses
Up to four wheat beer glasses, Pils
glasses, etc. can be hung in the beer
glass holders on the lefthand side in
the bottom basket.
If necessary, the beer glass holders
can be folded up out of the way.
The beer glass holders can be replaced with two cup racks supplied
as extras, which also serve as Prosecco glass or champagne glass
holders.
1. Remove beer glass holders by pulling upwards and pressing lightly on
the hooks from below.
2. Attach cup racks onto the horizontal bars A or B using the hooks.
Press lightly to snap onto the hooks.
3. Remove the cup racks in the same
way as for the beer glass holders.
4. For wheat beer glasses of normal
size attach the beer glass holders to
horizontal bar A, for much shorter
glasses on B.
20
The bars that fix the beer glass
holders or cup racks can be removed, if required.
1. Push the bars back using the
thumbs (see the picture).
1
Important: Risk of injury:
Do not take hold of the bars with
the hand; place the hand under the
bars on the cutlery basket for support.
2. Fix the bars again by pushing them
forwards.
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and
long, sharp cutlery in the upper basket.
• Arrange items of crockery on and
under the folding cup racks so
that they are offset from each
other and water can reach all
items.
21
• The cup racks can be folded up
out of the way for tall crockery
items.
• Lay or hang wine and brandy
glasses in the slots in the cup
racks.
• For glasses with long stems, fold
the glass rack to the right, otherwise fold it away to the left.
• The row of spikes on the left of
the upper basket is also in two
parts and can be folded away.
Spikes not folded away: place
glasses, mugs etc. in the upper
basket.
Spikes folded away: More room
for serving dishes.
22
Adjusting the height of the upper basket
Maximum height of dishes in the
3
Upper basket
Lower basket
with upper basket raised
22 cm
30 cm
with upper basket lowered
24 cm
29 cm
The height of the baskets can also be adjusted when they are loaded.
Raising / Lowering the upper basket
1. Pull out the upper basket completely.
2. Holding the upper basket by the
handle, raise it as far as it will go
and then lower it vertically.
The upper basket will latch into the
lower or the upper position.
23
Adding detergent
1
Detergents remove the dirt from
dishes and cutlery.
The detergent must be added before
the cycle starts.
Only use detergent intended for domestic dishwashers.
The detergent compartment is located on the inside of the door.
1. If the lid is closed:
Press the release button.
The lid will spring open.
3
24
2. Place the detergent in the detergent
dispenser. The markings indicate the
dosing levels for powder detergents:
“20/30” corresponds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions with regard to dosing and
storage.
3. Close the lid and press until it locks
into place.
In the case of very heavily soiled
dishes, fill the adjoining compartment (1) with additional detergent.
This detergent comes into use during the pre-wash cycle.
Concentrated detergents
2
Today’s detergents for dishwashers are almost exclusively low-alkaline
concentrated detergents with natural enzymes in tablet or powder
form.
Using 50°C dishwashing cycles in conjunction with these concentrated
detergents reduces pollution and is good for your dishes, as these dishwashing cycles are specially matched to the dirt-dissolving properties
of the enzymes in concentrated detergents. It is for this reason that using 50 °C dishwashing cycles in conjunction with concentrated detergents can achieve the same cleaning results that can otherwise only be
achieved using 65 °C cycles.
Detergent tablets
3
Detergent tablets from different manufacturers dissolve at different
rates. For this reason, some detergent tablets do not attain their full
cleaning power during short cycles. Therefore please use dishwashing
cycles with pre-wash when using detergent tablets.
25
Using 3in1 detergents
3
3
26
These products are detergents with a combined cleaning, rinsing and
salt function.
When the 3in1 function is activated,
– the addition of special salt and rinse aid from the respective dispenser
is prevented.
– If the salt and rinse aid dispensers are empty, this is not indicated.
– The dishwashing cycles can be up to 30 minutes longer.
If you want to use 3in1 detergents, check whether these detergents are
suitable for your water hardness. (Follow manufacturer’s instructions!)
If your water hardness is higher than that recommended by the manufacturer but you would nevertheless like to use 3in1 detergent, proceed
as follows:
• With the 3in1 function selected, set the water softener one hardness
setting lower than when rinsing without 3in1 detergent.
• Fill up the dispenser (if this is empty) with special salt.
The dishwasher remembers the two different settings of the degree of
hardness for rinsing with and without 3in1 function.
If you want to use 3in1 products
1. Press the ON/OFF button.
2. Go to the 3 IN 1 option.
3. Set the value to ON (see section “Adjusting an option/setting”
symbol lights up in the symbol line.
Before the start of the dishwashing cycle put 3in1 detergent in the detergent dispenser.
As the rinse aid inflow is automatically switched off when the 3in1
function is activated, it may come about because of the different quality standards in the 3in1 detergent, that the dishes do not dry sufficiently.
If this happens, proceed as follows (see section “Adding rinse aid”):
• Fill up the dispenser (if this is empty) with rinse aid.
• Set rinse aid dosage to “2” mechanically.
• Activate rinse aid inflow.
If you do not want to use 3in1 products any more
If you want to stop using 3in1 products, please do the following:
• Deactivate the 3in1 function.
• Fill up the dispensers for salt and rinse aid again.
• Switch the water softener to the highest setting and perform up to
three normal cycles without loading any dishes.
• Then set the water softener to the water hardness in your area.
If you want to use 4in1 products
When using "4 in 1" detergents that integrate also anti- glass corrosion
agent into "3 in 1" formula, please follow the same indication as given
for "3 in 1" detergents.
27
Selecting the dishwashing cycle (Cycle Table)
•
•
•
•
Dinner service
and cookware,
normally soiled
temperature-sensitive crockery
•
•
•
•
•
50° NORMAL5)
Dinner service
and cookware
normally soiled
•
•
•
•
•
45° GLASS
Dessert dishes
and coffee service, delicate
glassware
lightly soiled
-
•
•
•
15
Water (litres)
•
PREWASH
(cold)6)
Used dishes that are
All types of dish- being stored in the
es
dishwasher and are
to be washed later.
•
-
-
-
-
9
23 - 25
18 - 20
12 - 14
14 - 16
0,8
30
120 - 130
1,8 - 2,0
1,2 - 1,4
0,95 - 1,05
0,55 - 0,65
ENERGY
(50°)
90 - 100
65° NORMAL
130 - 160
70° INTENSIVE4)
95 - 105
30 MINUTES
(60°)3)
normally soiled,
dried-on food remains
13 - 25
•
Dinner service
and cookware
1,0 - 1,5
•
AUTOMATIC
(50°-65°)2)
90 - 110
•
4
Energy (kWh)
normally soiled
dried-on food remains
-
0,9
Dinner service
and cookware
•
< 0,1
•
-
73
heavily soiled,
dried-on food remains, in particular
protein and starch
•
12
Dinner service
and cookware
Drying
•
Final rinse
-
1 to 2x
Dishes, excluding just used, lightly to
saucepans
normally soiled
•
2x
•
2x
•
Consumption
values1)
Length (minutes)
Type of
soiling
Main wash
Suitable
for:
Pre-wash
Dishwashingcycle
Intermediate rinse
Programme
sequence
1) The consumption values were obtained under standardised conditions. They depend on how
full the baskets for the dishes are. Variations are therefore possible in practice.
2) When using this cycle the degree of water clouding determines the amount of soiling on the
dishes. The length of the cycle and water and energy consumption can vary greatly – depending upon the load and how dirty the dishes are. Depending upon the soiling, the temperature
of the water will be automatically adjusted to between 50°C and 65°C.
3) When using this cycle, only load the dishwasher half full.
28
4) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e.g. babies’ bottles, plastic chopping boards or jam jars.
5) Test programme for Test Institutes
6) This cycle does not need any detergent.
29
Selecting a programme
When your dishes look like this, select:
an intensive programme.
a normal or energy-saving programme.
a short programme (e.g. 30 minute
programme).
30
Starting a dishwashing cycle
3
3
3
3
1. Check that the spray arms can turn freely.
2. Turn the water tap on fully.
3. Close the door.
4. Press the ON/OFF button.
5. Using the direction buttons ( or ) select the desired cycle.
The name of the selected dishwashing cycle will flash. To the right of
the name the estimated length of the programme is displayed.
6. Press the OK/START button.
The selected dishwashing cycle will start. In the text line in the display
you can see the name of the current stage in the programme. Next to
this you can see the estimated time remaining in minutes.
Using the OPTION button you can briefly display the name of the dishwashing cycle in the display.
A dishwashing cycle can only be started from the Programmes menu.
During the dishwashing cycle, the remaining time shown in the display
may be adjusted according to the size of the load, degree of soiling, etc.
If the dishwashing cycle does not start:
If after pressing the OK/START button the cycle does not start and a
message appears in the display, (REFILL RINSE AID, REFILL SALT or
PLEASE CLOSE DOOR):
• Follow the instructions in the message.
After the problem has been remedied, the cycle starts automatically.
With the messages REFILL RINSE AID or REFILL SALT you can nevertheless start the cycle by pressing the OK/START button again.
While a dishwashing cycle is running, you cannot make changes to options or settings.
31
Interrupting or aborting a dishwashing cycle
Only interrupt a dishwashing cycle that is in progress if it is absolutely
necessary.
1
Interrupting the dishwashing programme by opening the dishwasher door
Hot steam may escape when the door is opened. There is a risk of scalding.
1. Open the door carefully. The dishwashing cycle will stop, in the display:
PLEASE CLOSE DOOR
2. Close the door. The cycle will continue.
3
32
Aborting the dishwashing cycle
1. Press the RESET button.
In the display: CONFIRM CANCEL ?
2. Press the OK/START button.
The programme is cancelled. In the display: CHOOSE PROGRAMME
3. If you want to start a new dishwashing cycle, check whether there is
any detergent in the dispenser.
Turning off the dishwasher will only interrupt a selected dishwashing
cycle, not cancel it. The cycle will recommence after turning the dishwasher back on again.
Setting the delay start
3
With the delay start you can delay the start of a dishwashing cycle for
between 1 and 19 hours. First of all set the delay start and then the desired dishwashing cycle.
1. Go to the DELAY START option; see section “Adapting an option/setting”.
2. Set the period by which you wish to delay the start in hours.
In the symbol line of the display .
3. Press the OPTION button, to change to the Programmes menu.
4. Select programme and start.
First of all the pre-set time delay until the start runs down. In the display you see the time remaining until the start of the dishwashing cycle. After the time delay until the start has elapsed, the dishwashing
cycle starts automatically, the symbol goes out.
Cancelling a delay start:
You can cancel a delay start that is counting down at any time.
1. Press the RESET button.
In the display: CONFIRM CANCEL ?
2. Press the OK/START button.
The delay start is cancelled. The dishwasher cycle that is set begins.
33
Switching off the dishwasher
Switch off the dishwasher if the messages PROGRAMME END and
PLEASE SWITCH OFF are being displayed alternately.
With some dishwashing cycles, the drying fan continues to run even after the end of the cycle.
If the acoustic signal has been enabled, a continuous tone will sound
for approx. 15 seconds at the end of the dishwashing cycle.
If the dishwasher is not switched off, then the acoustic signal is repeated after 3 minutes and after 6 minutes.
1. Press the ON/OFF button. Display goes out.
2. Turn off the water tap.
1
Carefully open the door. Hot steam may escape.
• Hot dishes are sensitive to knocks. Therefore leave the dishes to cool
for about 15 minutes before removing them. You also get a better
drying result.
• Dishes dry more quickly if you open the door for a moment after the
cycle has ended and then leave it slightly open.
Removing the dishes
3
It is normal for the inner door and the dispensers to be damp.
• Empty the lower basket first, then the upper basket. This way you
avoid dripping water from the upper basket onto dishes in the lower
basket.
• The dishwasher's interior light will always be on when the door of the
appliance is open. Therefore, in order to save energy, you should always close the door of the dishwasher after having loaded or removed dishes.
34
Care and cleaning
1
Do not use furniture care products or aggressive cleaners.
• When necessary, clean the dishwasher’s controls with a soft cloth and
clean warm water.
• Occasionally check the internal dispensers, door seal and water inlet
filter (if fitted) for dirt and clean them, if necessary.
Cleaning the filters
3
The filters must be regularly checked
and cleaned. Dirty filters will spoil the
wash results.
1. Open the door and remove the lower
basket.
2. Turn the handle about ¼ of a turn
anticlockwise (A) and remove the filter system (B).
3. Grasp the grip hole on the fine filter
(1) and remove it from the micro-filter (2).
4. Clean all filters thoroughly under
running water.
35
5. Remove the flat filter (3) from the
base of the washing compartment
and clean both surfaces thoroughly.
6. Re-insert the flat filter.
7. Place the fine filter in the micro-filter and fit the two together.
8. Insert the filter system in place and
lock it by turning the handle clockwise as far as it will go. Ensure that
the flat filter does not protrude
above the base of the washing compartment.
1
Under no circumstances may the dishwasher be used without its filters.
Cleaning the spray arm jets
3
Regularly check the jets in the spray
arms for blockages. When cleaning is
necessary, remove spray arm from the
fixture and clean jets with a pointed
object (wire or needle). Then rinse out
the spray arm using a strong jet of
water.
Do not damage the jet opening.
Upper basket spray arm
1. To remove upper basket spray arm,
tilt it down hard.
2. Clean spray arms jets.
36
3. Place cleaned upper basket spray arm
back in position against the connecting piece: press the two together
firmly, until you feel them snap into
place.
Bottom spray arm
1. To remove bottom spray arm, pull it
upwards out of its catch.
2. Clean spray arm jets.
3. Place bottom spray arm back in position against connecting piece and
press down firmly, until you feel it
snap into place.
37
What to do if …
Resetting the language
You can reset the language of the display to the factory setting at any
time. As well as the language, the CONTRAST1 and BRIGHTNESS settings
are also reset.
1. Press the RESET button repeatedly until the display in the display no
longer changes.
2. Press and hold the RESET button for six seconds.
In the text line LANGUAGE ENGLISH appears. The word ENGLISH flashes.
3. Using the direction buttons or select the desired language.
4. Press the OK/START button.
5. If required, adjust the values for CONTRAST1 to BRIGHTNESS; see the
section “Basic operation”.
Remedying small malfunctions
If one of the following fault messages is displayed in the display during
operation:
– OPEN THE TAP
– DRAIN BLOCKED
Remedy the fault, then re-start the dishwashing cycle. The cycle will
continue.
In the case of other fault messages:
– Cancel the dishwashing cycle.
– Switch the appliance off and on again.
– Select dishwashing cycle.
– Press the OK/START button.
If the fault is displayed again, please contact the Customer Care Department and inform them of the fault message.
1. not available with all models
38
Malfunction
Possible cause
Remedy
Water tap is blocked with
limescale or faulty.
Check the water tap and
have it repaired if necessary.
The tap is turned off.
Turn the tap on.
The filter (where present) in
Clean the filter in the
the threaded hose fitting on
threaded hose fitting.
the tap is blocked.
1 short warning tone,
continuously repeated,
can be heard,
in the display: OPEN THE Filters in the base of the
TAP
washing compartment are
blocked.
Abort the dishwashing cycle
(see section: Starting a dishwashing cycle);
clean filters (see section:
Cleaning the filters).
Water inflow hose
Check the position of the
has not been correctly posihose.
tioned.
2 short warning tones,
continuously repeated,
can be heard,
in the display: DRAIN
BLOCKED
(There is water in the
dishwasher’s internal
dispenser)
The sink outlet is blocked.
Clean out sink outlet.
Water drain hose
Check the position of the
has not been correctly posihose.
tioned.
3 short warning tones,
continuously repeated,
The anti-flood system has
can be heard,
been triggered.
in the display: SERVICE
CODE
First shut off the water tap,
then switch off the appliance and contact the Customer Care Department.
1 long warning tone
can be heard,
in the display: SPRAYARM BLOCKED
The top basket spray arm is
blocked.
Open the door carefully .
Hot steam may escape when
the door is opened. There is a
risk of scalding. Arrange the
dishes and cutlery in the
baskets so that the spray arm
above can rotate freely.
Close the dishwasher door.
In the display: PLEASE
CLOSE DOOR
The door of the dishwasher
is open.
Close the dishwasher door.
39
Malfunction
The cycle is not starting.
Possible cause
Remedy
The mains plug is not
plugged in.
Plug in mains plug.
A fuse in the house’s wiring
Replace fuse.
system is defective.
For dishwasher models with
If the dishes are to be
a delay start timer:
washed immediately, cancel
A start time has been selectthe delay start.
ed.
Rust spots are visible in
the dishwashing compartment.
The dishwashing compartment is made from rust-free
stainless steel. Rust spots in
the washing compartment
are due to rust particles
Only wash cutlery, dishes and
from external sources (rust pans that are suitable for
particles from water pipes, dishwasher use.
pans, cutlery, etc.). Remove
such spots with a commercially-available cleaning
product for stainless steel.
A whistling noise can be
The whistling is not a cause
heard when washing
for concern.
dishes.
The dishwasher interior
light does not come on.
40
The mains plug is not
plugged in.
Decalcify appliance with
commercially available
agents for cleaning dishwashers.
If the noises can still be
heard after decalcifying the
machine, use a different
brand of detergent for washing cutlery and dishes.
Plug in mains plug.
The bulb in the interior light Contact the Customer Care
is faulty.
Department.
If the dishwashing results are not satisfactory
The dishes are still dirty.
• The wrong dishwashing cycle was selected.
• The dishes were loaded is such a way that the dishwashing water did
not reach all items. The baskets for the dishes must not be overloaded.
• Filters in the floor of the dishwasher are not clean or incorrectly inserted.
• Good quality detergent was not used, or too little was used.
• In the case of scale deposits on the dishes: The special salt dispenser is
empty or the water softening system has been incorrectly set.
• The drain hose is incorrectly positioned.
• If at the end of the dishwashing cycle there is still detergent left in
the detergent dispenser, either the spray arm was jammed or the
spray arm jets are blocked with pollutants in the dishwashing water.
You have the option of removing the spray arms from their fixture for
cleaning (see section “Care and Cleaning”).
The dishes do not dry and are not shining.
• Poor quality rinse aid was used.
• The rinse aid dispenser is empty.
There are smears, streaks, milky spots or a shiny bluish coating on
glasses and dishes.
• Lower rinse aid dosage.
There are dried water drops on the glasses and dishes.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer's customer advice centre.
Glass corrosion
• Contact the detergent manufacturer's customer advice centre.
41
Disposal
2
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste disposal facilities.
Old appliance
W
1
42
The symbol
on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you
purchased the product.
Warning! When your appliance has finished its working life, remove
the plug from the socket. Cut off the cable and plug and dispose of
them.
Break the door lock so that the door no longer shuts. This prevents children from trapping themselves inside and endangering their lives.
Technical data
Capacity:
12 place settings including serving dishes
Permitted water pressure:
1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa)
Electrical connection:
AC 220 - 240 V, 50 Hz, 10 A; also see the rating plate on the
right-hand side of the dishwasher’s interior door .
Total output
2100 - 2300 W
Dishwashers that can be integrated and built-in
5
Dimensions:
820 - 880 x 596 x 570 (H x W x D in mm)
Max. weight:
50 kg
This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
43
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the
appliance fully loaded and using the test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be carried out when the salt
dispenser in the water softener and the rinse aid dispenser have been
filled with salt and rinse aid respectively, and using the test cycle (see
“Cycle Table”).
Full load:
12 place settings
including serving dishes
Half load:
6 place settings including serving
dishes, leaving alternate positions
in the rack free
Amount of detergent
required:
5g + 25g (Type B)
20g (Type B)
Rinse aid setting:
4 (Type III)
4 (Type III)
Example loading arrangements:
Upper basket *)
*) If there are cup racks in place on the lefthand side or the cutlery tray is in place, remove them.
44
Lower basket with cutlery basket*)
Cutlery basket
*) If necessary, you can remove the cup racks on the left-hand side and/or the beer
glass holder.
45
Installation and connection instructions
1 Safety information for the installation
• Only transport the dishwasher in an upright position, otherwise salt
water may run out.
• Before using the dishwasher for the first time, check for any damage
caused in transport. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your
supplier.
• Never use the dishwasher if the mains cable, water inlet or drain hose
are damaged; or if the control panel, work top or plinth area are
damaged such that the inside of the appliance is freely accessible.
• Always plug the mains plug into a correctly installed shockproof
socket.
• Permanent connection: a permanent connection must only be installed by a trained electrician.
• Prior to using the appliance for the first time, ensure that the rated
voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be
found on the rating plate.
• Multi-way plugs / connectors and extension cables must not be used.
This could constitute a fire hazard through overheating.
• The dishwasher’s cable must only be replaced by the Customer Care
Department or a registered electrician.
• A water inlet hose with safety valve must only be replaced by the
Customer Care Department.
46
Installing the dishwasher
• The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level in all directions.
• To compensate for unevenness in
the floor and to match the height
of the appliance to that of surrounding units, extend the threaded feet using a screwdriver.
• Adjust the rear feet of the appliance using a cordless screwdriver
from the front of the appliance.
(See installation instructions.)
• The drain hose, inlet hose and
mains cable must be laid so that
they are able to move freely within
the plinth area, and so that they
are not kinked or crushed when the dishwasher is in position.
• The dishwasher must also be screwed tightly to the work surface or to
the adjoining units. This is essential to ensure the dishwasher does
not tip up.
Dishwashers that can be integrated
3
(see installation template supplied)
The door of the appliance can be fitted with a wooden door/cupboard
door with the following dimensions:
Width:
591 – 594 mm
Depth:
16 – 24 mm
Height:
(variable)
dependent on
Weight:
max. 8 kg
– Recess height
– Plinth height
– Adjusting the dishwasher to match the height of
adjoining units
The exact height must be measured at the place of installation from the adjoining units.
47
Connecting the dishwasher
Connecting to the water supply
• The dishwasher can be connected to cold and hot water supplies up
to max. 60°C.
• The dishwasher must not be connected to open hot water appliances
or instantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure:
1 bar (=10 N/cm2 =100 kPa)
Consult your plumber if the water pressure is less than 1 bar.
Highest permitted water pressure:
10 bar (=100 N/cm2 =1 MPa)
If the water pressure is greater than 10
bar, a pressure reduction valve must be
used (available from your dealer).
Connecting the inlet hose
1
3
48
The water inlet hose must not be kinked, crushed or entangled when it
is being connected.
Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet
hose to a tap with an external thread (¾ inch). The inlet hose is fitted
with either a plastic or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make sure that the tap is
not dripping.)
So that access to the tap in the kitchen is not restricted by the use of
the dishwasher, we recommend installing an additional tap, or fitting a
T-branch to the existing tap.
If you need a longer water inlet hose than that supplied, the following
VDE-approved complete hose sets are to be used. These are available
from your local dealer.
– Hose kit “WRflex 100” (Code: 911 239 034)
– Hose kit “WRflex 200” (Code: 911 239 035)
Water drainage
The drain hose must not be kinked,
crushed or entangled.
• Connecting the drain hose:
maximum permitted height above
the bottom edge of the appliance:
60 cm.
Extension hoses
• Extension hoses are available from
your dealer or from our Customer
Care Department. To ensure that
the function of the appliance is not
impeded, the internal diameter of
extension hoses must be 19 mm.
• The total length including extension hoses must not exceed 4 metres.
permitted distance
1
Drain hose
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all commonly available
sink outlet types. The outer diameter of the sink outlet connection
must be at least 15 mm.
• The drain hose must be fixed to the sink outlet connection using the
hose clamp supplied.
Anti-flood system
For protection from water damage, the dishwasher is equipped with a
anti-flood system.
In the event of a fault, the safety valve in the water inlet hose immediately interrupts the supply of water to the appliance and the drain
pump is activated. In this way water can neither escape nor overflow.
The remaining water in the appliance is automatically pumped out.
Should a fault occur when the appliance is switched on, a buzzing tone
can also be heard.
49
Electrical connection
Details about the voltage, type of supply and the fuses required are to
be found on the rating plate. The rating plate is located on the righthand inner edge of the dishwasher door.
To isolate the dishwasher from the mains, pull out the mains plug.
Important:
– The plug must be accessible after the appliance has been installed.
– Following installation, live parts and insulated wiring must not be accessible to a test finger in accordance with DIN EN 60335-1.
Connecting systems
The water inlet hose, drain hose and the mains cable must all be connected to the side of the dishwasher as there is no space for them behind the appliance.
2 connection pieces 45° or
straight, outer ø 19 mm,
length 30 mm
waterinlet
50
mains
cable
doublevalve
watermains socket
drainage
waterdrainage
waterinlet
mains cable
Guarantee Conditions
Belgium
DECLARATION OF GUARANTEE TERMS.
Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result.
This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil Code. The statutory rights that the consumer has under this legislation are not
affected by this declaration of guarantee terms.
This declaration does not affect the vendor's statutory warranty to the end user. The appliance is
guaranteed within the context of and in adherence with the following terms:
1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of charge any
defect that occurs within 24 months from the date the appliance is delivered to the first end user.
These guarantee terms do not apply in the event of use for professional or equivalent purposes.
2. Performing the guarantee means that the appliance is returned to the condition it was in before
the defect occurred. Defective parts are replaced or repaired. Parts replaced free of charge become
our property.
3. So as to avoid more severe damage, the defect must be brought to our attention immediately.
4. Applying the guarantee is subject to the consumer providing proof of purchase showing the purchase and/or delivery date.
5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic),
synthetic materials and rubber, is the result of inappropriate use.
6. The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of the appliance.
7. The statutory warranty does not apply when defects are caused by:
• a chemical or electrochemical reaction caused by water,
• abnormal environmental conditions in general,
• unsuitable operating conditions,
• contact with harsh substances.
8. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. Nor will the guarantee cover those caused by inadequate installation or assembly, lack
of maintenance or failure to respect the assembly instructions or directions for use.
9. Defects that result from repairs or measures carried out by people who are not qualified or expert
or defects that result from the addition of non-original accessories or spare parts are not covered
by the guarantee.
10. Appliances that are easy to transport may be delivered or sent to the consumer services department. Home repairs are only anticipated for bulky appliances or built-in appliances.
11. If the appliances are built-in, built-under, fixed or suspended in such a way that removing and replacing them in the place where they are fitted takes more than half an hour, the costs that result
therefrom will be charged for. Connected damage caused by these removal and replacement operations will be the responsibility of the user.
12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the repair costs are considered disproportionate, in agreement with the consumer, the defective appliance may be replaced with another appliance of the same value.
In this event, we reserve the right to ask for a financial contribution calculated according to the
length of time it has been used.
13. A repair under guarantee does not mean that the normal guarantee period will be extended nor
that a new guarantee period begins.
14. We give a twelve month guarantee for repairs, limited to the same defect.
15. Except in the event where liability is legally imposed, this declaration of guarantee terms excludes
any compensation for damage outside the appliance for which the consumer wishes to assert his
rights. In the event of legally admitted liability, compensation will not exceed the purchase price
paid for the appliance.
These guarantee terms are only valid for appliances purchased and used in Belgium. For exported
appliances, the user must first make sure that they satisfy the technical conditions (e.g.: voltage,
frequency, installation instructions, type of gas, etc.) for the country concerned and that they can
51
withstand the local climatic and environmental conditions. For appliances purchased abroad, the
user must first ensure that they meet the qualifications required in Belgium. Non-essential or requested adjustments are not covered by the guarantee and are not possible in all cases.
Our consumer services department is always at your disposal, even after the guarantee period has
expired.
Address for our consumer services department:
ELECTROLUX HOME PRODUCTS BELGIUM
Bergensesteenweg, 719 - 1502 LEMBEEK
Tel.: 02.363.04.44
Weitere Kundendienststellen im Ausland
In diesen Ländern gelten die Garantiebedingungen der örtlichen Partner. Diese können dort eingesehen werden.
Further after-sales service agencies overseas
In these countries our AEG-Electrolux agents’ own guarantee conditions are applicable. Please obtain further details direct.
Autres agences étrangères assurant le service après-vente
Dans ces pays, les conditions de garantie des concessionnaires de la région sont valables. Vous pouvez les consulter sur place.
Otros puntos de Postventa en el extranjero
En estos países rigen las condiciones de nuestros representantes locales.
las cuales pueden ser consultadas allí mismo.
Ulteriori uffici del servizio tecnico assistenza clienti all’estero
In questi paesi sono valide le condizioni di garanzia dei partner locali.
Queste condizioni possono essere esaminante sul luogo.
Serviços de assistência técnica no estrangeiro
Nestes países são válidas as condições de garantia dos concessionários
locais, podendo aí ser consultadas.
További vevöszolgálati irodák külföldön
Ezekben az országokban a mi AEG-Electrolux vevöszolgálatainknál
saját jótállási feltételek alkalmazhatók. A további adatokat kérjük
közvetlenül szerezzék be.
Servisne službe
Na garancijskem listu boste našli seznam pooblašèenih servisnih
služb AEG-Electrolux.
52
Customer Service Centres
Belgium
Electrolux Home Products Belgium
ELECTROLUX SERVICE
Bergensesteenweg 719
1502 Lembeek
E-mail:
consumer.services@electrolux.be
Consumer services
Tel.:
02/363.04.44
Fax.:
02/363.04.00
02/363.04.60
U.A.E. Abu Dhabi
Universal Trading Company
P.O. Box 43 99
Tel.: 6335331
Service Center 6733974
Jordan
Jordan Household
Supply Co. Ltd.
P.O. Box 3/68
Amman/Tel.: 69 70 50
Malta
ITC
International Trading Company
White House Building
Mountbatte Street
Blata L-Bajda/Tel.: 220644
Egypt
Middle East Commercial
Center
4 Salah El Dein St. - 2nd floor
Heliopolis, Kairo
Egypt
Tel.: 2024181719
Canada
EURO-LINE Appliances
2150 Winston PARK Drive 20
Oakville, Ontario L6H 5V1
Tel.: 905 829 3980
Fax: 905 829 3985
Mauritius
Happy World Centre Ltd.
P.O. 7 54
1 Chausee Street
Port Louis
Tel.: 25355
Australia
The Andi-Co Group
1 Stamford Road
Oakleigh VIC 3166
Tel.: (03) 9569 1255
Fax: (03) 9569 1450
www.andico.com.au
Korea (South)
Core Incorp.
3/F Chewoo Bldg.
200 Nonhyun-Dong
Kangnam-Ku 135-010
Seoul
Telefon 82 2 549 89 61
Namibia
AEG NAMIBIA (PTY)
LIMITED-Jeppe Street
Northern Industrial Area
Windhoek
Tel.: (061) 21-6082/4
Fax: (061) 217838
Bahrain/Arabian Gulf
A.A. Zayani & Sons
P.O. Box 9 32
Bahrain
Tel.: 17311124
Croatia
Electrolux D.O.O.
Suplova 7
10000 Zagreb
Tel.: 1 61 19512
Fax: 1 61 19513
New Zealand
Monaco Corporation Ltd.
10 Rothwell Avenue
Albany - Auckland
4399 Auckland 1
New Zealand
Tel.: 00 64-92 59 11 11
Fax: 00 64-92 59 11 12
Bulgaria
Electrolux Bulgaria E.O.O.D.
91 Levski Blvd.
1000 Sofia
Tel.: 2 806676
Fax. 2 980 5276
Kuwait/Arabian Gulf
Ali Al-Ghanim Est.
P.O. Box 21540 - Safat
Tel.: 4822190
Fax: 4820116
Syria
WATTAR CO.
P.O. Box 36109
Mazzeh - Damascus
Direct Phone: 00963116132649
Fax: 00963116119537
Cyprus
Hadjikyrlakos & Sons Ltd.
Prodromou 121
P.O. Box 21587
Nicosia 1511
Service Telephones:
Nicosia 02 481226
Limassol 05 562182
Larnaca 04 633929
Paphos 06 932 699
Lebanon
Adib & Assaferi
P.O. Box 539
Tripoli
Iran
ARIAN International Development Co.
AEG Showroom
Shariati, Balatar as Safar
Teheran / Iran
Phone No. Showroom:
021 / 285 513 / 4
Phone No. Service:
021 / 312 27 67 / 8
53
54
Estonia
Electrolux Estonia Ltd.
Mustamäe tee 24
EE0006 Tallinn
Tel.: (372) 6 650 090
Fax: (372) 6 650 092
Latvia
Electrolux Latvija Ltd.
Kr.Barona iela 130/2
Riga, LV-1012
Tel.: 371 7313626
Fax: 371 7845954
Poland
Electrolux Poland Sp. zo.o.
ul. Domaniewska 41
02-034 Warszawa
tel.: 022 874 33 33
fax: 022 874 33 00
Hong Kong
Dah Chong Hong Ltd.
20 Kai Cheung Road
Kowloon Bay
Kowloon - Hong Kong
Tel.: 0085222621620
Fax: 0085227550333
Lithuania
Electrolux Lithuania
Verkui 29
2600 Vilnus
Tel.: 372 272 3326
Fax: 372 272 3366
Russia
Electrolux Russia Ltd.
16 Olympiysky prospekt
129090 Moscow
Tel.: (095) 937 7837
Fax: (095) 926 5513
Israel
Evis Ltd.
Tadiran-Ampa Service
10 Gibonay Israel Street
New Industrial Zone
Netanya, 42504
Israel
Malaysia
Arzbergh Engineering
No. 49A/B, Jalan Petaling
Utama 7
4600 Petaling Jaya
Tel.: 3 795 1084
Fax: 3 795 1082
Saudi Arabia
Awad Badi Nahas Est
Shara Siteen
Jeddah 21463
Phone: 6646583
Alia Trading Co
Mecca Road
Riyadh 11491
Phone 4645977
Japan
Electrolux Japan Ltd.
Domestic Appliances
Department
Maruzen Showa Warehouse
Building
Tookai 4-5-12, Ota-ku
143-006 Tokyo
Tel.: 0120-13-7117
Fax: 03-3790-5257
Singapore
Group Pte Ltd.
833 Bukit Timah Road
Unit no. 01-11 Royalville
279887 Singapore
Tel.: 0065 64638484
Fax: 0065 64638488
Slovenia
Electrolux Slovenia D.O.O.
Traska Ul. 132
1000 Ljubljana
Tel.: 61 1234 137
Fax: 61 1234 238
Thailand
Olympia Thai Tower, 444
Rachadapiser Road
Samsennok- Huaykwang
10320 Bangkok
Thailand
Tel.: 006625136111
Fax: 006625136334
Slovakia Rep.
Electrolux Slovakia S.R.O.
Seberiniho 1
821 03 Bratislava
Tel.: 02 4333 4322, 4355
Fax: 02 4333 6976
South Africa
AEG (Pty) Ltd.
55, 12th Road
P.O. Box 1 02 64
Kew/Johannesburg 2000
Tel.: 8069111
Hungary
Electrolux Lehel KFT
Erzsébet Királyné útja 87.
1142 Budapest
Tel.: 00361/467-3200
Czech Rep.
ELECTROLUX DOMÁCå
SPOTØEBIÈE CZ
DIVIZE ELECTROLUX S.R.O.
Customer Centre
Hanusova ul.
140 21 Praha 4
Tel.: 2 6112 6112
Telefax: 2 6112 3504
Service
In the event of technical faults, please first check whether you can
remedy the problem yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem yourself, please contact the
Customer Care Department or one of our service partners.
In order to be able to assist you
quickly, we require the following
information:
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers see rating plate)
– Type of fault
– Any error messages displayed by
the appliance
So that you have the necessary reference numbers from your appliance
at hand, we recommend that you write them in here:
Model description:
.....................................
PNC:
.....................................
S No:
.....................................
55
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg-electrolux.de
© Copyright by AEG
822 612 930-00-090306-01
Subject to change without notice