SANTO
Integrated Refrigerator
Operating Instructions
Dear customer,
Before placing your new refrigerator into operation please read these
operating instructions carefully. They contain important information
for safe use, for installation and for care of the appliance.
Please keep these operating instructions for future reference. Pass them
on to possible new owners of the appliance.
These operating instructions are for use with several technically
comparable models with varying accessories. Please observe the notes
which apply to your model.
Notes which are important for your safety or for the correct
functioning of the appliance are indicated with a warning triangle and/
or the words (Warning!, Caution!, Important!). Please observe the
information carefully.
0 This symbol guides you step by step in the operation of the appliance.
1
3
Additional information regarding operation and practical use of the
appliance appear after this symbol.
2
Tips and information concerning economical and environmentally
sound use of the appliance are marked with the cloverleaf.
Explanations of the technical terminology used in the operating
instructions can be found at the end in the section "Technical
Terminology".
The operating instructions contain instructions for the correction of
possible malfunctions by the user in the section "Something not
working". If you are unable to rectify the fault after reading this
chapter, please contact your local AEG Service Force Centre..
If you require assistance or advice on your appliance, please contact
our Customer Care Department by letter or telephone:
Tel:
Customer Care Department
AEG Domestic Appliances Limited
55-77 High Street
Slough
Berkshire SL 1 1DZ
08705 350350
Printed on paper manufactured with environmentally sound processes.
he who thinks ecologically acts accordingly ...
2
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
The appliance needs ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
View of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Initial use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The fridge defrosts automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage Shelves/Storage Racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable door interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable Storage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
15
Hints and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Food Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Energy Saving Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
16
16
Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
17
17
3
Contents
Something not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4
1 Important
Safety Instructions
These warnings are provided in the interests of your safety. Ensure
that you understand them all before installing or using this
appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings or these warnings contact the Customer
Care Department.
Prior to Installation
• Check the refrigerator for transport damage. Under no circumstances
should a damaged appliance be installed! In the event of damage,
please contact your retailer.
Installation
• This appliance is heavy. Care should be taken when moving it.
• It is dangerous to alter the specifications or attempt to modify this
product in any way.
• Ensure that the appliance does not stand on the electrical supply
cable. If the supply cable is damaged, it must be replaced by a cable
available from your local Service Force Centre.
• Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
• Parts which heat up should not be exposed. Whenever possible, the
back of the appliance should be close to a wall, but leaving the required distance for ventilation, as stated in the installation instructions.
• The appliance should be left for 2 hours after installation before it is
turned on, in order to allow the refrigerant to settle.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant
circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain
that none of the components of the refrigerant circuit become
damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
5
Important Safety Instructions
Child Safety
• Do not allow children to tamper with the controls or play with the
product.
• There is a risk of suffocation! Keep packaging material away from
children!
During Use
• This appliance is designed for domestic use only, specifically for the
storage of edible foodstuffs only. It is not intended for commercial or
industrial use
• Containers with flammable gases or liquids can leak at low temperatures. Do not store any containers with flammable materials such as,
spray cans, fire extinguisher refill cartridges etc in the refrigerator.
Maintenance and Cleaning
• Before cleaning, always switch off the appliance and disconnect from
the electrical supply.
• When unplugging always pull the plug from the mains socket, do not
pull on the cable.
Servicing
• This product should be serviced by an authorised engineer and only
genuine spare parts should be used.
• Under no circumstances should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local Service Force
Centre.
6
Environmental Information
Packaging
All transit packaging materials are environmentally compatible and can
be reused. Wood is un-treated. The plastics can be recycled and are
identified as follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the
interior.
>PS< for polystyrene foam, e.g. the pads, which are pure hydrocarbon
compounds and can be recycled.
The carton parts are made from recycled paper. Please dispose of the
packaging with due care for the environment.
Old Appliances
When disposing of your old appliance:
Make the appliance unusable by cutting off the cable and remove any
door catches to ensure small children cannot be trapped inside.
Help to keep your country tidy - use an authorised disposal site.
Before Use
Packaging
0 Pull off the adhesive tape on the left and right side of the door.
Any remnants of adhesive can be removed with white spirit.
0 Remove all adhesive tape and packaging from the interior of the
appliance.
0 Remove the protection from the seal on the inside of the door.
0 Wash the inside of the appliance with lukewarm water with a little
bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap
or detergent as the smell may linger. Dry the appliance thoroughly.
3
7
Installation
Installation Location
The appliance should be installed in a well ventilated, dry room.
Energy use is affected by the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature corresponds to the climate classification, for which the appliance is designed.
The climate classification can be found on the rating plate, which is
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for
each climate classification:
8
Climate classification
for an ambient temperature of
SN
+10 to +32 °C
N
+16 to +32 °C
ST
+18 to +38 °C
T
+18 to +43 °C
The appliance needs ventilation
The integrated door of the furniture
cabinet largely seals the installation
recess. Integrated-appliances must therefore be provided with ventilation by
having an opening in the furniture
plinth. The warmed air must be able to
be exhausted upwards through the air
shaft on the furniture back. The ventilation cross-sections should be at least
200 cm2
Important! In order not to impair the
function of the appliance, never cover
or obstruct the ventilation openings.
Installation
See installation instructions supplied.
After installing the appliance, ensure the door seals correctly when closed. If the door does not seal tightly, this may lead to heavy frosting
and a higher energy consumption.
9
Installation
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
1
WARNING – THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety measures
not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate is
inside, on the left.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used.
Important
The wires in the mains lead are coloured in accordance with the following code:
Green
Green and Yellow Earth
& Yellow
Blue
Neutral
Brown
Live
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings indentifying the terminals Blue
Brown
in your plug, proceed as follows:
1. The wire coloured green and yellow must be connected to the
terminal marked with the letter
Cord Clamp
„E“ or by the earth symbol or
coloured green and yellow.
2. The wire coloured blue must be connected to the terminal „N“ or
coloured black.
3. The wire coloured brown must be connected to the terminal marked
„L“ or coloured red.
4. Upon completion there must be not cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
1
10
Warning! A cut-off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.
Description of the appliance
View of the appliance
(various models)
➀
➁
➂
➃
➄
➅
➆
➇
➈
Temperature regulator and interior lighting
Butter/cheese compartment with flap
Variable storage compartment (not included with all models,
design differs depending on the model)
Door storage compartments
Bottle shelf
Fruit- and vegetable drawers
Storage shelves
General purpose box (not included with all models)
Rating plate
Prior to Initial Start–Up
0 Please clean the appliance interior and all accessories prior to initial
start-up (see section: “Maintenance and Cleaning”).
11
Initial use
0 Insert plug into mains socket.
The temperature regulator is on
the right side in the refrigerator
compartment. It is also the ON/
OFF-switch.
Position "0" means:
Off, interior lighting off
Position "1"means:
Highest interior temperature (warmest setting)
Position "6" means:
Lowest interior temperature (coldest setting)
Recommended settings:
For normal use: position "2" - "3";
0 Turn the temperature regulator to the desired setting. The inside light
illuminates. The compressor starts and then runs automatically.
3
Goods to be refrigerated can be loaded immediately after switching on,
because the storage temperature in the refrigerator is quickly reached.
Note: From a food science point of view, +5 °C for the refrigerator
compartment should be considered cold enough as a storage temperature.
The following effects are of significance in respect of the interior temperature:
– Ambient temperature;
– Quantity and temperature of the food stored;
– Frequency with which the door is opened and how long it is left open.
Examples:
12
Ambient temperature
Temperature controller position
Approx. 10 °C
Range up to 1
Approx. 16 °C
Range about 2
Approx. 25 °C
Range about 2
Approx. 32 °C
2 to 3
Approx. 38 °C
1 to2
Important!
High ambient temperatures (e.g. on hot summer days) and a cold setting on the temperature regulator (position "5" to "6") can cause the
compressor to run continuously.
Reason: when the ambient temperature is high, the compressor must
run continuously to maintain the low temperature in the appliance. The
fridge will not be able to defrost since automatic defrosting of the
fridge is only possible when the compressor is not running (see also
"Defrosting" section). The result is the build up of a thick layer of frost
on the fridge rear wall.
If this happens, turn the temperature regulator back to a warmer setting (position "3" to "4"). At this setting the compressor will be switched on and off as usual and automatic defrosting will recommence.
Switching off the appliance
0 To switch off, turn the temperature regulator to position "0". The inside
light goes out.
0
0
0
0
If the appliance is to be removed from service for a lengthy period:
Turn the temperature regulator to position "0". The inside light goes
out.
Unplug the appliance, or isolate the power supply.
Clean thoroughly (see section: "Maintenance and Cleaning ").
Leave the door open to avoid the build up of odours.
Defrosting
The fridge defrosts automatically
The rear wall of the fridge covers with frost when the compressor is
running, and defrosts when the compressor is off.
The water from the thawing frost is collected in the drain channel on
the rear of the fridge, fed through the drain hole into the collection
compartment in the base, and then evaporated.
The drain hole must be cleaned regularly (see the section "Maintenance
and Cleaning".
13
Interior Accessories
Storage Shelves/Storage Racks
Depending on the model, your appliance is equipped with either glass
storage shelves or storage racks.
The glass shelf above the fruit and vegetable compartment must always
remain in this position so that fruit and vegetables stay fresh longer.
The height of the storage shelves
can be adjusted:
0 To do this pull the storage shelf
forward until it can be swivelled
upwards or downwards and removed.
0 Please do the same in reverse to
insert the shelf at a different
height.
Storing tall items:
0 Slide the half size glass storage
shelf in the upper or middle level
to the rear. By this means you will
gain space to place tall items on
the storage shelf below.
Variable door interior
Depending on your requirements, the storage compartments on the
door can be removed and repositioned in a different place.
14
Interior Accessories
Variable Storage Box
(not on all models, design differs depending on the model)
Some models are equipped with a variable storage box which is fitted
under a door shelf compartment and can be slid sideways.
The box can be inserted under
every door shelf compartment.
0 To change, lift the shelf compartment with the box upwards and
out of the holders in the door and
remove the retaining bracket out
of the guide under the shelf compartment.
0 Please do the same in reverse to
insert the shelf at a different
height.
The variable box can be hung from
a storage shelf in the refrigerator
compartment:
0 Pull the storage shelf forward until
it can be tipped up or down and
removed.
0 Hang the retaining bracket on the
taper on the storage shelf and
slide the storage shelf back into
the guides.
15
Hints and Tips
Normal Operating Sounds
• You may hear faint gurgling or bubbling sounds when the refrigerant
is pumped through the coils or tubing at the rear, to the cooling
plate/evaporator.
• When the compressor is on, the refrigerant is being pumped round
and you will hear a whirring sound or pulsating noise from the compressor.
• A thermostat controls the compressor and you will hear a faint click
when the thermostat cuts in and out.
Food Storage
To obtain the best performance from your refrigerator:
• Do not store warm food or evaporating liquids.
• Do not store food uncovered.
• Keep the time between buying chilled food and placing it in your
refrigerator as short as possible.
• Do not push food together too much, try to allow air to circulate
around each item.
2 Energy Saving Advice
• Do not install the appliance close to sources of heat, such as a cooker,
dishwasher or radiator.
• Locate the appliance in a cool well ventilated room and make sure
that the air openings of the appliance are not obstructed.
• Always leave warm food to cool down to room temperature before
placing in the fridge.
• Try to avoid keeping the door open for long periods or opening the
door too frequently as warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
• Ensure there are no obstructions preventing the door from closing
properly.
16
Maintenance and Cleaning
Before any maintenance or cleaning work is carried out DISCONNECT
the appliance from the ELECTRICITY supply.
Internal Cleaning
0 Clean the inside and accessories with warm water and bicarbonate of
soda (5 ml to 0.5 litre of water). Rinse and dry thoroughly.
Warning!
• Do not use detergents, abrasive powders, highly perfumed cleaning
products, wax polishes or cleaning products containing bleach or
alcohol.
0 Clean the drain hole of the water trough at regular intervals and ensure
that the drain hole is clear at all times. If blocked, carefully clear using
the green strip inserted into the drain outlet to remove the blockage.
0 Regularly check the door seals and wipe clean to ensure they are clean
and free from debris.
1
External Cleaning
0 Wash the outer cabinet with warm soapy water.
1
Warning!
• Do not use abrasive products
• There are sharp edges on the underside of the product so care should
be taken when cleaning.
Replacing the light bulb
1
0
0
0
0
0
Warning! Ensure the appliance is disconnected from the mains supply.
Light bulb specifications: 220-240 V, max. 15 W, socket: E 14
To switch the appliance off turn
the temperature regulator to
position "0" .
Unplug the mains plug.
To change the light bulb, remove
the screw and the light bulb cover
as shown.
Change the defective light bulb.
Refit the light bulb cover and the screw.
3
17
Something not Working
Before contacting your local Service Force Centre, check the following
points.
Symptom
Solution
Check there is power at the socket
No power to the appliance.
Check there is not a power cut by
checking the household lights.
Check the fuse has not blown.
Check the ambient temperature is within
the appliances operating limits
The temperature in the refrigerator is too
Check the thermostat is turned to the
high.
correct setting relative to ambient conditions.
Adjust the thermostat to give correct
temperature control.
Check that the door is closed.
The compressor runs continuously
Large quantities of food have recently
been placed in the cabinet and/or door is
frequently opened.
Check that air ventilation is not obstructed.
Ensure the bulb is correctly fitted.
The light does not come on.
Replace the bulb it has blown.
Check the door light switch is not jammed.
18
Excessive build up of frost.
If the door seal is not airtight (probably
after changing over the door hinges)
apply warm air to the non sealing area
using a hair dryer set to a gentle heat. (do
not use a fan heater for this purpose).
This will make the rubber more supple
and allow it to revert to its original shape.
Noise
Refer to Normal Operating Sounds
Symptom
Solution
The compressor does not start immediately after changing the temperature setting.
This is normal, the compressor starts after
a period of time.
Water on the floor
Water drain hole is blocked - see "Maintenance and Cleaning".
If after the above checks there is still a fault, call your local Service
Force Centre.
In-guarantee customers should ensure that the above checks have been
made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service
calls.
Regulations, Standards, Guidelines
This appliance was designed for household use and was manufactured
in accordance with the appropriate standards. The necessary measures
in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and
the regulations of the German Society of Electrical Engineers (VDE)
were observed in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks.
;
This appliance is in accordance with the following EU guidelines:
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.
– 89/336/EWG dated 3 May 1989
(including guideline change notice 92/31/EWG) - EMV guideline
– 94/2/EC dated 21. 01. 1994 - Directive on Energy Labelling
– 96/57 EC dated 3. 9. 1996 - Energy Efficiency Requirements of
Household Electric Refrigerators, Freezers and Combinations thereof
19
Technical Terminology
• Refrigerant
Liquids that can be used to a generate a cooling effect are known as
refrigerants. They have a relatively low boiling-point, indeed so low,
that the warmth from the food stored in the fridge or freezer can
cause the refrigerant to boil and vaporise.
• Refrigerant Circuit
Closed circulation system that contains the refrigerant. The refrigerant circuit comprises primarily of an evaporator, a compressor, a
condenser and pipe work.
• Evaporator
The refrigerant is evaporated in the evaporator. Similar to all other
liquids, refrigerant requires heat to evaporate. This heat is removed
from the interior of the appliance, as a result the interior is cooled.
The evaporator is therefore located inside the appliance or placed in
foam immediately behind the inner wall and thus not visible.
• Compressor
The compressor looks like a small drum. It is driven by a built-in electric motor and is mounted on the base of the appliance at the rear.
The task of the compressor is to draw in vaporised refrigerant from
the evaporator, to compress it, and to pass it on to the condenser.
• Condenser
The condenser normally has the form of a grid. The refrigerant compressed in the compressor is liquefied in the condenser. During this
process, heat is released to the surrounding air at the surface of the
condenser. The condenser is mounted on the base of the appliance.
20
Service & Spare Parts
If after carrying out the necessary checks there is still a fault with your
appliance please contact your local AEG Service Force Centre.
In guarantee customers should ensure that the suggested checks
have been made as the engineer will make a charge if the fault is
not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service
calls.
Service & Spare Parts
If you require a service engineer or wish to purchase spare parts,
contact your local AEG Service Force Centre, by telephoning
08705 929 929
Help us to help you
Please determine your type of enquiry before telephoning. When you
contact us we need to know.
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
–What is the fault?
–When does the fault occur?
4. The model, production number and product identification number.
5. Date of purchase.
This information can be found on the rating plate, so you have these
numbers to hand we recommend you write them below.
Model
.............................................
PNC no.
..............................................
S no.
.............................................
Customer care
For general enquiries regarding your AEG appliance, or for further
information on AEG products please contact our Customer Care
Department
AEG Domestic Appliances Limited
55-77 High Street
Slough
Berkshire SL 1 1DZ
Tel: 08705 350350
21
Guarantee Conditions
AEG offer the following guarantee to the first purchaser of this
appliance.
1. The guarantee is valid for 12 months commencing when the
appliance is handed over to the first retail purchaser, which
must be verified by purchase invoice or similar documentation.
The guarantee does not cover commercial use.
2. The guarantee covers all parts or components which fail due to
faulty workmanship or faulty materials. The guarantee does not
cover appliances where defects or poor performance are due to
misuse, accidental damage, neglect, faulty installation,unauthorised
modification or attempted repair, commercial use or failure to
observe requirements and recommendations set out in the
instruction book.
This guarantee does not cover such parts as light bulbs, removable
glassware, dust bags or filters.
3. Should guarantee repairs be necessary the purchaser must inform
the nearest customer service office (manufacturer´s service or
authorised agent). AEG reserves the right to stipulate the place of
the repair (i. e. the customer´s home, place of installation or AEG
workshop).
4. The guarantee or free replacement includes both labour and
materials.
5. Repairs carried out under guarantee do not extend the guarantee
period for the appliance. Parts removed during guarantee repairs
become the property of AEG.
6. The purchaser´s statutory rights are not affected by this guarantee.
22
Guarantee Conditions
European Guarantee
If you should move to another country within Europe then your
guarantee moves with you to your new home subject to the following
qualifications:
– The guarantee starts from the date you first purchased your product.
– The guarantee is for the same period and to the same extent for
labour and parts as exist in the new country of use for this brand or
range of products.
– This guarantee relates to you and connot be transferred to another
user.
– Your new home is within the European Community (EC) or European
Free Trade Area.
– The product is installed and used in accordance with our instructions
and is only used domestically, i. e. a normal household.
– The product is installed taking into account regulations in your new
country.
Before you move please contact your nearest Customer Care Centre,
listed below, to give them details of your new home. They will then
ensure that the local Service Organisation is aware of your move and
able to look after you and your appliances.
France
Senlis
+33 (0) 344 62 29 29
Germany
Nürnberg
+49 (0) 911 323 2600
Italy
Pordenone
+39 (0) 1678 47053
Sweden
Stockholm
+46 (0) 8 738 7910
UK
Slough
+44 (0) 1753 219 899
23
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
822 941 080 –01- 1099