Elo TouchSystems 1725L Series User's Manual

Add to my manuals
42 Pages

advertisement

Elo TouchSystems 1725L Series User's Manual | Manualzz
Elo Entuitive Touchmonitor
User Guide
17" LCD Desktop Touchmonitor
1725L Series
Revision A
P/N 008541
Elo TouchSystems, Inc.
1-800-ELOTOUCH
www.elotouch.com
Copyright © 2001 Elo TouchSystems Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written
permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves
the right to revise this publication and to make changes from time to time in the content hereof
without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo
TouchSystems, Inc.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.
i
ii
Table of Contents
Chapter 1
Appendix B
Introduction
1
Touchmonitor Safety
21
Precautions . . . . . . . . . . . . . . . . . . . . 1
About the Product . . . . . . . . . . . . . . . . . 1
Care and Handling of Your Touchmonitor. . . . 23
Chapter 2
Technical Specifications
Installation and Setup
Appendix C
3
Compatibility Modes . . . . . . . . . . . .
VESA Modes . . . . . . . . . . . . . .
Display Timing . . . . . . . . . . . . . .
Touchmonitor Specifications . . . . . . . .
AccuTouch Touchscreen Specifications .
IntelliTouch Touchscreen Specifications .
17" LCD Desktop Touchmonitor
(ET1725L-XSWA-1) Dimensions . . . . .
Product Overview . . . . . . . . . . . . . . . . . 4
Main Unit . . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . 4
Connecting Your Touchmonitor . . . . . . . . . . 5
Video Cable Connection . . . . . . . . . . . . 6
Touchscreen Cable Connection . . . . . . . . 7
Power Cable Connection. . . . . . . . . . . . 8
Video Input Pin Assignment . . . . . . . . . . . . 9
Installing the Driver Software . . . . . . . . . . 10
Installing the Touch Driver for Windows 2000,
Me, 95/98 and NT 4.0 . . . . . . . . . . . 10
Chapter 3
Operation
Touchmonitor Controls . . . . . . . . .
Screen Adjustments . . . . . . . . . . .
Main Menu . . . . . . . . . . . . . .
H-POSITION . . . . . . . . . . .
V-POSITION . . . . . . . . . . .
CLOCK . . . . . . . . . . . . . .
PHASE . . . . . . . . . . . . . .
AUTO CONFIG Adjustment. . . .
INPUT (D-Sub input source only) .
SYSTEM INFORMATION . . . . .
RECALL. . . . . . . . . . . . . .
SHARPNESS . . . . . . . . . . .
COLOR . . . . . . . . . . . . . .
OSD ADJUST . . . . . . . . . . .
CONTRAST . . . . . . . . . . . .
BRIGHTNESS . . . . . . . . . .
EXIT. . . . . . . . . . . . . . . .
11
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
13
13
14
14
14
14
14
15
15
15
15
15
16
16
16
16
Chapter 4
Troubleshooting Tips
17
Appendix A
Native Resolution
19
iii
25
.
.
.
.
.
.
.
.
.
.
.
.
25
25
26
27
28
29
. . 30
Regulatory Information
31
Index
35
iv
C
H A P T E R
1
INTRODUCTION
CHAPTER 1
Congratulations on your purchase of an Elo TouchSystems Entuitive LCD
desktop touchmonitor. Your new high-resolution industrial touchmonitor
combines the reliable performance of Elo’s touch technology with the latest
advances in LCD display design. This combination of features creates a natural
flow of information between you and your touchmonitor.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit. See Appendix B for more
information on touchmonitor safety.
About the Product
Your LCD desktop touchmonitor is a 17" TFT color display with the following
features:
• Direct analog RGB input
• 17.0" diagonal screen size
• 16.7 million displayable colors
• 1280 x 1024 resolution
• DOS/ VGA/ SVGA/ XVGA/ SXGA/ EGA/ CGA/ Mac compatible
• Frequency H-sync: 30-80k Hz; V-sync: 50-85kHz (up to 75khz @ 1280 x
1024)
1-1
• Plug & Play
• High quality full screen re-scaling
• VESA DDC 1/2B data communication
• VESA DPMS power saving
• Worldwide agency approvals that include UL, CUL, TÜV- Bauart, FCC, CE,
C-Tick, VCCI
• IntelliTouch or AccuTouch Technology
For full Product Specifications refer to Appendix C.
1-2
Elo Entuitive Touchmonitor User Guide
C
H A P T E R
2
INSTALLATION AND SETUP
CHAPTER2
This chapter discusses how to setup your LCD desktop touchmonitor and how
to install Elo TouchSystems driver software.
Please make sure that the following items are included in the carton and are in
good condition.
Video cable
Serial touchscreen
cable
Brick
power supply
Quick Installation Guide
Monitor power cable
(US/Canada)
CD
Software
User
Guide
European monitor
power cable
2-3
Product Overview
Main Unit
LCD Display
Rear View
2-4
Elo Entuitive Touchmonitor User Guide
Connecting Your Touchmonitor
Before connecting the cables to your touchmonitor and computer, be sure that the
touchmonitor and computer are off.
Video cable
Serial touchscreen
cable
Brick
power supply
Female 9-pin Serial
touchscreen
connector
Female 15-pin
video connector
Monitor power cable
(US/Canada)
Power
European monitor
power cable
Connections on underside
Figure 2.1
Touchmonitor cables and connections
2-5
Video Cable Connection
Connections on underside
Female 15-pin
video
connector
Video
cable
Video
port
Ferrite bead
1 Set the touchmonitor on a solid horizontal surface, such as a table or desk.
2 Connect the female end of the video cable connector to the back of the LCD
monitor, and connect the other end to the back of the computer.
3 Secure the cable to your touchmonitor and computer by tightening the screws
on the connector clockwise.
2-6
Elo Entuitive Touchmonitor User Guide
Touchscreen Cable Connection
Connections on underside
Female 9-pin serial
touchscreen
connector
Serial
touchscreen
cable
1 Connect the female end of the 9-pin touchscreen cable to the serial port on
the back of your computer.
2 Connect the male end of the cable to the serial touchscreen connector on your
touchmonitor.
3 Secure the cable to your touchmonitor and computer by tightening the screws
on the connector clockwise.
2-7
Power Cable Connection
Connections on underside
Brick power cable port
Serial
touchscreen
cable
Brick power supply
Power cable
1 Depending on where you live, you will use either the European or
US/Canadian power cable. Connect the female end of the power cable to the
Brick power supply.
2 Connect the Brick power supply into the power port on the touchmonitor.
To protect your equipment against risk of damage from electrical surges in the power
line, plug the Brick supply’s power cord into a surge protector, and then connect the
surge protector to a grounded (three-pronged) AC electrical outlet.
2-8
Elo Entuitive Touchmonitor User Guide
Video Input Pin Assignment
This section describes the pin assignment of the LCD’s 15 Pin Mini D-sub
(video cable) connector.
Pin No.
Signal Connector
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red Video Signal
Green Video Signal
Blue Video Signal
N.C.
Ground
Ground for red video signal
Ground for green video signal
Ground for blue video signal
N.C.
Ground
N.C.
DDC data
Horizontal sync signal
Vertical sync signal
DDC clock
2-9
Installing the Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to
work with your computer. Drivers are located on the enclosed CD-ROM for the
following operating systems:
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
Additional drivers and driver information for other operating systems (including
MS DOS, Windows 3.x, OS/2, Macintosh and Linux) are available on the Elo
TouchSystems web site at www.elotouch.com.
Your Elo touchmonitor is plug-and-play compliant. Information on the video
capabilities of your touchmonitor is sent to your video display adapter when
Windows starts. If Windows detects your touchmonitor, follow the instructions
on the screen to install a generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.
Installing the Touch Driver for Windows 2000, Me, 95/98
and NT 4.0
NOTE:
For Windows 2000 and NT 4.0 you must have administrator access rights to install the
driver.
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
If the AutoStart feature for your CD-ROM drive is active, the system
automatically detects the CD and starts the setup program.
2 Follow the directions on the screen to complete the driver setup for your
version of Windows.
If the AutoStart feature is not active:
1 Click Start > Run.
2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
3 Click Open, then OK to run EloCd.exe.
4 Follow the directions on the screen to complete the driver setup for your
version of Windows.
2-10
Elo Entuitive Touchmonitor User Guide
C
H A P T E R
3
OPERATION
CHAPTER3
Variations in video output and application will likely require you to adjust your
touchmonitor to optimize the quality of the display.
For best performance, your monitor should be operating in native resolution;
that is, 1280 x 1024 at 75 Hz. Use the Display control panel in Windows to
choose 1280 x 1024 resolution.
Operating in other resolutions will degrade video performance. For further
information, please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This
feature saves you from having to reset your choices every time you unplug or
power your touchmonitor off and on. If there is a power failure, your
touchmonitor settings will not default to the factory specifications.
3-11
Touchmonitor Controls
All adjustments are made using the on-screen display (OSD) controls.
Figure 3.1
Touchmonitor Controls
Control
Function
Power
Press the power key to turn the monitor on. Press it again to turn the
monitor off.
Enable or disable the OSD adjustment menu. Move from the submenu back
to the previous menu.
To select the adjustment items from the OSD menu.
Menu
Select
Adjust
Adjust
Power LED
3-12
To scroll up in the menu or to increase the value of the selected item.
To scroll down in the menu or to decrease the value of the selected item.
The LED will be green when the monitor is in the normal ON mode, and
will be orange when it is in the power saving mode.
Elo Entuitive Touchmonitor User Guide
Screen Adjustments
The setting switches are normally in stand-by mode.
1 Push the MENU button once to display the main menu of the screen
adjustment. The adjustable items will be displayed in the main menu.
2 Use the ADJUST
and ADJUST
buttons to select the desired setting
icon.
3 Push the SELECT button to enter the sub-menu.
4 Once the sub-menu appears, use the ADJUST
and ADJUST
buttons
to change the setting values.
5 After making the adjustment, push the SELECT button to memorize the
setting.
6 Select YES at EXIT item of main menu after making the adjustment.
7 Return and exit the main menu.
To go back to the previous menu, push the MENU button.
Exit the screen adjustment, go to the EXIT item and select YES or NO.
If no adjustments are made within 20 seconds (default OSD time out), the
monitor goes back to the stand-by mode. To make adjustments press the MENU
button to display the main menu.
Main Menu
The OSD main menu (Figure 3.2 below) is displayed on screen when the
MENU button is pressed. The OSD menu is a combination of graphic and text
display. The column inside the OSD menu will show information of input
image. Second column beneath OSD menu shows the item selected.
The LEFT and RIGHT keys are used to scroll through items within the menu.
The selected item is highlighted as the scrolling move along. The SELECT key
is used to activate the highlighted item during this state.
Figure 3.2
OSD Main Menu
3-13
H-POSITION
H-Position is used to adjust the horizontal image position. A slider with the
current value is displayed.
V-POSITION
V-Position is used to adjust the vertical image position manually. A slider with
the current value is displayed.
CLOCK
Reduce vertical stripes in the screen image.
PHASE
Reduce horizontal stripes in the screen image.
AUTO CONFIG Adjustment
This function will automatically set the parameters of PHASE, CLOCK,
H-POSITION, and V-POSITION.
NOTE:
To manually change the AUTO CONFIG adjustments, you can adjust PHASE, CLOCK,
H-POSITION, and V-POSITION in the OSD.
1 Click the Windows Start button and choose the Shut Down option.
NOTE:
The background wallpaper color cannot be black.
2 Press the Menu button and select the AUTO CONFIG option.
3 Choose the AUTO ADJUST option then press SELECT. The picture will
auto-adjust by itself. After 8 seconds, you can exit the OSD and SHUT
DOWN the frame.
4 If you are not satisfied with the picture quality, adjust the CONTRAST
option, see page 3-16.
3-14
Elo Entuitive Touchmonitor User Guide
Use the ADJUST
and ADJUST key to scroll up and down in menu, then
press the SELECT key to start this function. If the MENU key is pressed, the
main menu is re-displayed and no changes have been made.
Control
Function
AUTO ADJUST
Used to perform automatic configuration of the phase, clock,
vertical, and horizontal positioning.
It can tune the clock & phase to the best condition automatically.
AUTO TRACKING
AUTO POSITION
AUTO COLOR
RETURN
It is used to center the image automatically. Both horizontal and
vertical position is adjusted such that the image is centered on the
panel.
It is used to adjust the gain and offset of the Red, Green and Blue
channels on the ADC automatically.
Returns to main menu.
INPUT (D-Sub input source only)
Not applicable.
SYSTEM INFORMATION
This menu provides the user with detailed information regarding the current
input format and version (include resolution, vertical /horizontal frequency,
pixel clock and software version).
RECALL
Recall is used to reload all factory default parameters.
SHARPNESS
Sharpness adjusts the video quality to be sharp or blurry (for text mode).
COLOR
COLOR is a sub-menu which contains items to adjust the PC graphic imaging.
Menu Item
Function
RED
RED is used to adjust the gain of the red channel in ADC. A slider with the
current value is displayed.
GREEN is used to adjust the gain of the green channel in ADC. A slider with
the current value is displayed.
BLUE is used to adjust the gain of the blue channel in ADC. A slider with the
current value is displayed.
Return to the Main menu
GREEN
BLUE
RETURN
3-15
OSD ADJUST
Control
Function
OSD H POSITION
OSD V POSITION
OSD BLENDING
RETURN
Used to setup the OSD menu H position.
Used to setup the OSD menu V position.
Adjusts the blending of the OSD menu.
Return to the Main menu.
CONTRAST
Contrast allows you to adjust the difference between black and white shades for
image sharpness.
BRIGHTNESS
Allows you to set the brightness of the panel.
EXIT
Exit the OSD functions. Select YES to memorize the setting and exit or select
NO to exit without saving the parameters.
NOTE:
3-16
If a button is not pressed within 20 seconds, the OSD menu will disappear and parameter
changes will not be saved.
Elo Entuitive Touchmonitor User Guide
C
H A P T E R
4
TROUBLESHOOTING TIPS
CHAPTER4
If you are experiencing trouble with your touchmonitor, refer to the following
table. If the problem persists, please contact your reseller or our technical
support at 1-800-557-1458.
4-17
Problem
Suggestion(s)
No image appears on screen.
Check that the video cable and power connectors are
properly connected as described in Chapter 2.
Make sure the pins of the connectors are not crooked or
broken.
Check that power switch of the touchmonitor has been
pressed and LED on the front of touchmonitor is lit.
Test the power supply by trying different cables, or a
different wall outlet or plug another appliance into the
outlet.
Make certain the video cable is properly connected and that
it is not damaged. Check for bent pins on the cable
connectors.
Ensure that your computer and video card are properly
configured (consult video card documentation) and the
video card is firmly seated in the card slot of the computer
motherboard.
Check whether the resolution of your computer is higher
than that of the LCD touchmonitor.
Check that the video cable from the monitor has been
securely and correctly connected to the video connector at
the rear of the computer.
Reconfigure the resolution of your computer to make it less
than or equal to 1280 x 1024. See Appendix A for more
information on resolution.
Use the Auto Tracking function to make an adjustment. See
Chapter 3 for more information.
Check and reconfigure the touchmonitor mode of the
vertical refresh rate of your graphic card to make it
compatible with the LCD touchmonitor.
Make sure the VGA signal cable (or adapter) is well
connected.
Check and reconfigure the display mode of the vertical
refresh rate of your graphic card to make it compatible with
the LCD touchmonitor.
Make sure the touchscreen cable is securely connected at
both ends.
Partial image or incorrectly displayed
image
Image is unstable and flickering
Image is scrolling
Touch does not work
4-18
Elo Entuitive Touchmonitor User Guide
A
P P E N D I X
A
NATIVE RESOLUTION
CHAPTER4
The native resolution of a monitor is the resolution at which the LCD panel is
designed to perform best. In almost all cases, screen images look best when
viewed at their native resolution. You can lower the resolution setting of a
monitor but not increase it. For the Elo LCD touchmonitor, SXGA-17 inch, the
native resolution is 1280 x 1024.
Input Video
17" LCD
640 x 480 (VGA)
800 x 600 (SVGA)
1024 x 768 (XGA)
1280 x 1024 (SXGA)
Transforms input format to 1280 x 1024 size
Transforms input format to 1280 x 1024 size
Transforms input format to 1280 x 1024 size
Displays in native resolution
The native resolution of an LCD is the resolution that matches the LCD’s
pixels. Video performance is always best at native resolution settings. The
various standard LCD resolutions are usually represented as follows:
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
SXGA
1280 x 1024
A-19
For example, a SVGA resolution LCD panel displays 800 pixels horizontally
and 600 pixels vertically. Input video is also represented by the same terms.
XGA input video has a format of 1280 pixels horizontally by 1024 pixels
vertically. When the input pixels contained in the video input format match the
native resolution of the panel, there is a one-to-one correspondence of mapping
of input video pixels to LCD pixels. For example, the pixel in 45 column and 26
row of the input video is in 45 column and 26 row of the LCD. When the input
video is set at a lower resolution than the native resolution of the LCD, the
direct correspondence between the video pixels and the LCD pixels is lost. The
LCD controller can compute the correspondence between video pixels and LCD
pixels using algorithms contained in the controller. The accuracy of the
algorithms determines the fidelity of conversion of video pixels to LCD pixels.
Poor fidelity conversion can result in artifacts in the LCD display, such as
characters of varying width.
A-20
Elo Entuitive Touchmonitor User Guide
A
P P E N D I X
B
TOUCHMONITOR SAFETY
CHAPTER 4
This manual contains information that is important for the proper setup and
maintenance of your touchmonitor. Before setting up and powering on your new
touchmonitor, read through this manual, especially Chapter 2 (Installation), and
Chapter 3 (Operation).
&$87,21
5,6.2)(/(&75,&6+2&.
'212723(1 &$87,21
7RUHGXFHWKHULVNRIHOHFWULFVKRFNGRQRW
UHPRYHFRYHURUEDFN
1RXVHUVHUYLFHDEOHSDUWVLQVLGH
5HIHUVHUYLFLQJWRTXDOLILHGSHUVRQQHO
1 Turn off the touchmonitor before cleaning.
2 Your brick supply is equipped with a 3-wire, grounding power cord. The
power cord plug will only fit into a three-prong safety ground outlet. Do not
attempt to fit the plug into an outlet that has not been configured for this
purpose. Do not use a damaged power cord. Use only the power cord that
comes with your Elo TouchSystems touchmonitor. Use of an unauthorized
power cord may invalidate your warranty.
B-21
3 This display should be installed on a solid horizontal base.
4 Adequate ventilation must be maintained to ensure reliable and continued
operation and to protect the display from overheating. Do not block
ventilation slots and openings with objects or install the display in a place
where ventilation may be hindered.
5 This display should be operated from the type of power source indicated on
the AC/DC adapter.
6 Do not install this display near a motor or transformer where strong
magnetism is generated. Images on the display will become distorted and the
color irregular.
7 Do not allow metal pieces or objects of any kind fall into the display from
ventilation holes.
8 Do not attempt to service this unit yourself. Removal of the display cover
may expose you to dangerous voltage or other risks. Refer all servicing to
qualified service personnel.
9 Unplug this product from the wall outlet and refer servicing to qualified
service personnel in the event that:
1 Liquid is spilled into the product or the product is exposed to rain or water.
2 The product does not operate normally when the operating instructions are
followed.
3 The product has been dropped or the cabinet has been damaged.
4 The product exhibits a distinct change in performance, indicating a need
for service.
5 Power cord or plug is damaged or frayed.
B-22
Elo Entuitive Touchmonitor User Guide
Care and Handling of Your Touchmonitor
The following tips will help keep your Elo Entuitive touchmonitor functioning
at the optimal level.
• To avoid risk of electric shock, do not disassemble the brick supply or
display unit cabinet. The unit is not user serviceable. Remember to unplug
the display unit from the power outlet before cleaning.
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do
not use thinner or benzene, abrasive cleaners or compressed air.
• To clean the brick supply or display unit cabinet, use a cloth lightly
dampened with a mild detergent.
• Avoid getting liquids inside your brick supply or touchmonitor. If liquid does
get inside, have a qualified service technician check it before you power it on
again.
• Do not wipe the screen with a cloth or sponge that could scratch the surface.
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the
rag and wipe the touchscreen. Never apply the cleaner directly on the
touchscreen.
B-23
B-24
Elo Entuitive Touchmonitor User Guide
A
P P E N D I X
C
TECHNICAL SPECIFICATIONS
CHAPTER4
Compatibility Modes
Your Elo Entuitive touchmonitor is compatible with the following standard
video modes. All specifications are typical and subject to change.
VESA Modes
Horizontal
Vertical
Mode
Resolution
Total
Nominal Freq.
+/- 0.5 kHz
Nominal Freq.
+/- 1 Hz
Nominal Pixel
Clock (MHz)
DOS
VGA
720 x 400@70Hz
900 x 449
31.469
70.087
28.322
640 x 480@60Hz
800 x 525
31.469
59.940
25.175
640 x 480@72Hz
832 x 520
37.861
72.809
31.500
640 x 480@75Hz
840 x 500
37.500
75.000
31.500
800 x 600@56Hz
1024 x 625
35.156
56.250
36.000
800 x 600@60Hz
1056 x 628
37.879
60.017
40.000
800 x 600@72Hz
1040 x 666
48.077
72.188
50.000
800 x 600@75Hz
1056 x 625
46.875
75.000
49.500
1024 x 768@60Hz
1344 x 804
48.363
60.004
65.000
1024 x 768@70Hz
1328 x 806
56.476
70.069
75.000
1024 x 768@75Hz
1312 x 800
60.023
75.029
78.750
1152 x 864@75Hz
1600 x 900
67.500
75.000
108.00
1280 x 1024@60Hz
1688 x 1066
63.981
60.020
108.00
1280 x 1024@75Hz
1688 x 1066
79.976
75.025
135.00
SVGA
XGA
SXGA
C-25
Display Timing
IBM MODES
Mode
Resolution
Total
Horizontal
Nominal Freq.
+/- 0.5 kHz
Vertical
Nominal
Freq. +/- 1
Hz
Nominal Pixel
Clock (MHz)
EGA
CGA
DOS
VGA
XGA
640 x 350@70Hz
800 x 449
31.469
70.086
25.175
640 x 400@70Hz
800 x 449
31.469
70.086
25.175
720 x 400@70Hz
900 x 449
31.469
70.087
28.322
640 x 480@60Hz
800 x 525
31.469
59.940
25.175
1024 x 768@72Hz
1304 x 798
57.515
72.1
75.000
MAC MODES
Mode
Resolution
Total
Horizontal
Nominal Freq.
+/- 0.5 kHz
VGA
640 x 480@60Hz
800 x 525
31.469
59.940
25.175
640 x 480@67Hz
864 x 525
35.000
66.667
30.240
832 x 624@75Hz
1152 x 667
49.725
74.551
57.283
1024 x 768@60Hz
1312 x 813
48.780
60.001
64.000
1024 x 768@75Hz
1328 x 804
60.241
74.927
80.000
SVGA
XGA
C-26
Elo Entuitive Touchmonitor User Guide
Vertical
Nominal
Freq. +/- 1
Hz
Nominal Pixel
Clock (MHz)
Touchmonitor Specifications
Display Type
17” TFT
Resolution
SXGA 1280 x 1024 Max.
Pixel dimension
0.264 mm (H) x 0.264 mm (V)
LCD display color
16.7M Colors max.
OSD controls
Manual controls
H/V Position, Clock, Phase, Auto Config, Input, Information,
Recall, Sharpness, Color, OSD Adjust, Contrast, Brightness, Exit
Menu, Select, Adjust (3,4), Power.
Viewing angle
H: ± 60× max. V: ± 60× max.
Tilt
+30°, -5°
Contrast ratio
400:1Typ.
Brightness
250 cd/ m2/panel
225 cd/m2 IntelliTouch
220 cd/m2 AccuTouch
Rise time 45ms typ.
337.9 mm(H) x 270.3 mm(V)
Response time
Active display area
Input connector
Input AC 100 ~ 240V, 50 ~ 60Hz
Output +12 V DC, 4-6A max.
Video Analog 0.7 Vp-p. 75 ohms
Sync. TTL Level, Positive/Negative, Separate Sync.
15 Pin D-Sub.
Regulation
UL, CUL, TÜV- Bauart, FCC, CE, C-Tick, VCCI
AC/DC adapter
Input signal
EMI FCC-B
Dimensions
445 mm (W) x 440 mm (H) x 190 mm (D).
Weight
8.7 Kgs. (unpacked)
Accessories
VGA cable, AC/DC adapter, US and European power cord, Mac
adapter, touch cable.
Operation 0 ~ 40°C
Temperature
Storage 20 ~ 60°C
Plug & Play
DDC 2B
C-27
AccuTouch Touchscreen Specifications
Mechanical
Positional Accuracy
Touchpoint Density
Touch Activation Force
Surface Durability
Expected Life Performance
Sealing
Standard deviation of error is less than 0.080 in. (2.03 mm). Equates to
less than ±1%.
More than 100,000 touchpoints/in2 (15,500 touchpoints/cm2).
Typically less than 4 ounces (113 grams).
Surface durability is that of glass, Mohs’ hardness rating of 7.
AccuTouch technology has been operationally tested to more than 35
million touches in one location without failure, using a stylus similar to a
finger.
Unit is sealed to protect against splashed liquids, dirt, and dust.
Optical
Light Transmission
Visual Resolution
Gloss (per ASTM D2457 using a
60-degree gloss meter)
(per ASTM D1003) 80%; ±5%
All measurements made using USAF 1951 Resolution Chart, under 30X
magnification, with test unit located approximately 1.5 in (38 mm) from
surface of resolution chart.
Antiglare surface: 6:1 minimum.
Antiglare surface: Flat: 90 ± 20 gloss units.
Environmental
Chemical Resistance
Electrostatic Protection
(per EN 61 000-4-2)
The active area of the touchscreen is resistant to all chemicals that do not
affect glass, such as:
Acetone
Methylene chloride
Methyl ethyl ketone
Isopropyl alcohol
Hexane
Turpentine
Mineral spirits
Unleaded Gasoline
Diesel Fuel
Motor Oil
Transmission Fluid
Antifreeze
Ammonia based glass cleaner
Vinegar
The touchscreen withstands 20 discharges of 15KV, distributed randomly
across the active area of the touchscreen with proper transient protection.
See http:/www.elotouch.com/products/accutec/accuspec.asp for complete and
updated specifications.
C-28
Elo Entuitive Touchmonitor User Guide
IntelliTouch Touchscreen Specifications
Mechanical
Positional Accuracy
Touchpoint Density
Touch Activation Force
Surface Durability
Expected Life
Performance
Sealing
Standard deviation of error is less than 0.080 in. (2.03 mm). Equates to less than
±1%.
More than 100,000 touchpoints/in2 (15,500 touchpoints/cm2).
Typically less than 3 ounces (85 grams).
Surface durability is that of glass, Mohs’ hardness rating of 7.
No known wear-out mechanism, as there are no layers, coatings, or moving parts.
IntelliTouch technology has been operationally tested to more than 50 million
touches in one location without failure, using a stylus similar to a finger.
Unit is sealed to protect against splashed liquids, dirt, and dust.
Optical
Light Transmission (per
ASTM D1003)
Visual Resolution
Gloss (per ASTM D2457
using a 60-degree gloss
meter)
90%
All measurements made using USAF 1951 Resolution Chart, under 30X
magnification, with test unit located approximately 1.5 in (38 mm) from surface of
resolution chart.
Antiglare surface: 6:1 minimum.
Antiglare surface: Flat: 85 ± 20 gloss units.
Environmental
Chemical Resistance
Electrostatic Protection
(per EN 61 000-4-2,
1995)
The active area of the touchscreen is resistant to all chemicals that do not affect glass,
such as:
Acetone
Toluene
Methyl ethyl ketone
Isopropyl alcohol
Methyl alcohol
Ethyl acetate
Ammonia-based glass cleaners
Gasoline
Kerosene
Vinegar
Meets Level 4 (15 kV air/8 kV contact discharges).
See http://www.elotouch.com/products/inteltec/intelspec.asp for complete and
updated specifications.
C-29
17" LCD Desktop Touchmonitor (ET1725L-XSWA-1)
Dimensions
NOTE:
C-30
Dimensions in millimeters [inches]
Elo Entuitive Touchmonitor User Guide
REGULATORY INFORMATION
CHAPTER4
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified herein will likely result in improper operation,
damage to the equipment or pose a fire hazard if the limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety hazard. Service
should be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an integral
safety ground wire and 3-prong connector intended for connection to a grounded
safety outlet.
1) Do not substitute the cord with other than the provided approved type.
Under no circumstances use an adapter plug to connect to a 2-wire outlet as
this will defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can
result in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are questions
about the installation prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B limits for
radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided
cords and cabling may compromise electrical safety or CE Mark Certification for
emissions or immunity as required by the following standards:
This Information Technology Equipment (ITE) is required to have a CE Mark
on the manufacturer’s label which means that the equipment has been tested
to the following Directives and Standards:
31
This equipment has been tested to the requirements for the CE Mark as
required by EMC Directive 89/336/EEC indicated in European Standard EN
55 022 Class B and the Low Voltage Directive 73/23/EEC as indicated in
European Standard EN 60 950.
D) General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the
equipment may cause interference with radio and television communications.
There is, however, no guarantee that interference will not occur in any particular
installation due to site-specific factors.
1) In order to meet emission and immunity requirements, the user must
observe the following:
a) Use only the provided I/O cables to connect this digital device with
any computer.
b) To ensure compliance, use only the provided manufacturer’s approved
line cord.
c) The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2) If this equipment appears to cause interference with radio or television
reception, or any other device:
a) Verify as an emission source by turning the equipment off and on.
b) If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected
receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device
does not use. (Unterminated I/O cables are a potential source of
high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle.
Do not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician.
32
Elo Entuitive Touchmonitor User Guide
33
34
Elo Entuitive Touchmonitor User Guide
INDEX
A
I
About the Product, 1
AccuTouch Touchscreen Specifications, 28
AUTO ADJUST, 15
AUTO COLOR, 15
AUTO CONFIG Adjustment, 14
AUTO POSITION, 15
AUTO TRACKING, 15
IBM MODES, 26
Installation and Setup, 3
Installing the Driver Software, 10
Installing the Touch Driver for Windows 2000, Me, 95/98
and NT 4.0, 10
Introduction, 1
B
L
BRIGHTNESS, 16
Light Transmission, AccuTouch, 28
Light Transmission, IntelliTouch, 29
C
M
Care and Handling of Your Touchmonitor, 23
CGA, 26
Chemical Resistance, AccuTouch, 28
Chemical Resistance, IntelliTouch, 29
CLOCK, 14
COLOR, 15
Color, blue, 15
Color, green, 15
Color, red, 15
Compatibility Modes, 25
Connecting Your Touchmonitor, 5
CONTRAST, 16
MAC MODES, 26
Main Unit, 4
D
Display Timing, 26
DOS mode, 25, 26
N
Native Resolution, 19
O
Operation, 11
OSD ADJUST, 16
OSD BLENDING, 16
OSD Controls, 12
OSD H POSITION, 16
OSD Main Menu, 13
OSD V POSITION, 16
P
E
EGA, 26
Electrical Safety Information, 31
Electrostatic Protection, AccuTouch, 28
Electrostatic Protection, IntelliTouch, 29
Emissions and Immunity Information, 31
EXIT, 16
Expected Life Performance, AccuTouch, 28
Expected Life Performance, IntelliTouch, 29
PHASE, 14
Positional Accuracy, AccuTouch, 28
Positional Accuracy, IntelliTouch, 29
Power, 12
Power Cable Connection, 8
Power LED, 12
Precautions, 1
Product Overview, 4
R
G
Gloss, AccuTouch, 28
Gloss, IntelliTouch, 29
H
Rear View, 4
RECALL, 15
Regulatory Information, 31
Resolution, 25
RETURN, 15
H-POSITION, 14
Index-35
S
Screen Adjustments, 13
Sealing, Accutouch, 28
Sealing, IntelliTouch, 29
Select, 12
SHARPNESS, 15
Surface Durability, AccuTouch, 28
Surface Durability, IntelliTouch, 29
SVGA, 19, 25
SVGA, Mac Mode, 26
SXGA, 25
SYSTEM INFORMATION, 15
T
Technical Specifications, 25
Touch Activation Force, AccuTouch, 28
Touch Activation Force, IntelliTouch, 29
Touchmonitor Controls, 12
Touchmonitor Safety, 21
Touchmonitor Specifications, 27
Touchpoint Density, AccuTouch, 28
Touchpoint Density, IntelliTouch, 29
Touchscreen Cable Connection, 7
Troubleshooting Tips, 17
V
VESA Modes, 25
VGA, 19, 25, 26
VGA, Mac Mode, 26
Video Cable Connection, 6
Video Input Pin Assignment, 9
Visual Resolution, AccuTouch, 28
Visual Resolution, IntelliTouch, 29
V-POSITION, 14
X
XGA, 19, 25, 26
XGA, Mac mode, 26
Index-36

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement