TD503_01-36 02.2.26 10:09 AM Page 1
OWNER’S
MANUAL
“EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.”
19-INCH COLOR TV/DVD/VHS
EWC19T2
This Owner’s Manual is
made of recycled paper.
SUPPLIED ACCESSORIES
ACCESSORIES
PART NO.
Remote Control Unit NE203UD
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR ®
Partner, our company has
determined that this product meets
the ENERGY STAR ® guidelines for
energy efficiency. ENERGY STAR ® is
a U.S. registered mark.
Batteries
2 AA Batteries
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-256-2487.
Please read before using this equipment
TD503_01-36 02.2.26 10:09 AM Page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
AMEUBLES- Cet appareil ne doit
être placé que sur un meuble (avec
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation
d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug TV/DVD/VHS from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by
the TV/DVD/VHS manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/DVD/VHS near
water-for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
8.Accessories-Do not place this TV/DVD/VHS on an unstable
cart, stand, tripod, bracket, or table. The TV/DVD/VHS may
fall, causing serious injury to someone, and serious damage
to the appliance. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with the
TV/DVD/VHS. Any mounting of
PORTABLE CART WARNING
the appliance should follow the
manufacturer’s instructions and
should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination
should be moved with care.Quick
stops, excessive force, and uneven
S3126A
surfaces may cause the appliance
and cart combination to overturn.
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV/DVD/VHS and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the
TV/DVD/VHS on a bed, sofa, rug, or other similar surface.
This TV/DVD/VHS should never be placed near or over a
radiator or heat register. This TV/DVD/VHS should not be
placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
10.Power Sources-This TV/DVD/VHS should be operated
only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For TV/DVD/VHSs intended to operate from
battery power, or other sources, refer to the operating
instructions.
11.Grounding or Polarization-This TV/DVD/VHS is
equipped with a polarized alternating-current line plug(a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
-2-
EN
1B15
TD503_01-36 02.2.26 10:09 AM Page 3
F IGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECT RICAL CODE
ANTE NNA
L EAD I N
WI RE
GROUND
CLAMP
A NTENNA
DI SCHARG E UN I T
(NEC SECTION 8 10 -2 0)
EL ECT RI C
SE RV I CE
EQ U I PM EN T
G RO UNDI NG CO NDUCT ORS
(NEC SECTION 8 10 -2 1)
G RO UND CL AM PS
NEC - NATI O NAL EL ECTRI CAL CO DE
POWER SERVI C E G RO UNDI NG
EL EC TR O DE SYST EM
(NEC ART 2 50 , PART H)
S2 8 9 8 A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/DVD/VHS, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/DVD/VHS
receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV/DVD/VHS due to
lightning and power-line surges.
19.Damage Requiring Service-Unplug this TV/DVD/VHS
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD/VHS.
c. If the TV/DVD/VHS has been exposed to rain or water.
d. If the TV/DVD/VHS does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions, as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the TV/DVD/VHS to its normal operation.
e. If the TV/DVD/VHS has been dropped or damaged in any
way.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/DVD/VHS through openings as they may
touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the TV/DVD/VHS.
f. When the TV/DVD/VHS exhibits a distinct change in performance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to
this TV/DVD/VHS, ask the service technician to perform
routine safety checks to determine that the TV/DVD/VHS
is in proper operating condition.
22.Heat-This TV/DVD/VHS product should be situated away
from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/DVD/VHS
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
-3-
EN
1B15
TD503_01-36 02.2.26 10:09 AM Page 4
PRECAUTIONS
LASER SAFETY
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to service this device, due to possible eye injury.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
-4-
EN
1B15
TD503_01-36 02.2.26 10:09 AM Page 5
LOCATION
WARNING
For safe operation and satisfactory performance of
your TV/DVD/VHS, keep the following in mind
when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from
sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top and bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the TV/DVD/VHS near strong magnetic
fields.
• Avoid moving TV/DVD/VHS to locations where
temperature differences are extreme.
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a TV/DVD/
VHS which has moisture, it may damage the DVD
and TV/DVD/VHS. Therefore when the condensation
occurs inside the unit, turn the POWER button on
and allow at least 2 hours for the unit to dry out.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting
•
•
•
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/DVD/VHS disc loading tray.
Do not place anything directly on top of the unit.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/DVD/VHS has the same
serial number as yours. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
-5-
EN
1C29
TD503_01-36 02.2.26 10:09 AM Page 6
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . .2
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .9
C PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTIONS . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPT JACKS . . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO A STEREO
SYSTEM (for DVD) . . . . . . . . . . . .13
CONNECTING TO AN AMPLIFIER
EQUIPPED WITH DIGITAL INPUT
JACKS, MD DECK OR DAT DECK
(for DVD) . . . . . . . . . . . . . . . . . . . .13
CONNECTING TO A DOLBY
DIGITAL DECODER
OR DTS DECODER (for DVD) . . .14
C SET UP FOR USE . . . . . . . . . . . . .15
CHANNEL SET UP
FOR THE FIRST TIME . . . . . . . . .15
DELETING (OR ADDING)
CHANNEL . . . . . . . . . . . . . . . . . . .15
CHANNEL SET UP AGAIN . . . . . .16
SELECTING THE LANGUAGE . .16
DAYLIGHT-SAVING TIME . . . . . .16
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . . . . .17
TV/VCR SECTION
C TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C MTS(Multi-Channel Television
sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C VIDEO CASSETTE . . . . . . . . . . . . .25
C PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICAL HOLD CONTROL . . .26
C SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING
RECORDING . . . . . . . . . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C ON SCREEN DISPLAY . . . . . . . . .35
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
DVD SECTION
C ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
SYMBOLS USED IN
THIS MANUAL . . . . . . . . . . . . . . .36
C PLAYING A DISC . . . . . . . . . . . . . .37
PLAYING A DVD VIDEO OR AN
AUDIO CD . . . . . . . . . . . . . . . . . . .36
USING THE DVD MENUS . . . . . .36
USING THE TITLE MENU . . . . . .36
RESUMING PLAYBACK
FROM THE POINT WHERE
PLAYBACK STOPPED . . . . . . . . .38
FAST FORWARD/REVERSE . . . . .38
PAUSING PLAYBACK OR DISPLAYING
A STILL PICTURE . . . . . . . . . . . . .38
STEPPING THROUGH FRAMES .38
-6-
SLOW MOTION . . . . . . . . . . . . . .39
PLAYING FROM A DESIRED
TITLE OR CHAPTER . . . . . . . . . .39
STARTING FROM A DESIRED
TIME COUNT . . . . . . . . . . . . . . . . .39
STARTING FROM A DESIRED
TRACK . . . . . . . . . . . . . . . . . . . . . .39
REPEAT . . . . . . . . . . . . . . . . . . . . .40
A-B REPEAT . . . . . . . . . . . . . . . . .40
MARKER . . . . . . . . . . . . . . . . . . . .41
PROGRAM (Audio CD) . . . . . . . . .41
RANDOM (Audio CD) . . . . . . . . . .42
ZOOM PLAYBCK . . . . . . . . . . . . .42
PLAYING AN MP3 DISC . . . . . . . .42
CHANGING THE ONSCREEN
DISPLAY DURING MP3
DISC PLAY . . . . . . . . . . . . . . . . . .43
PLAYING AN MP3 DISC FROM
A DESIRED TRACK . . . . . . . . . . .43
PLAYING AN MP3 DISC IN A
PROGRAMMED WAY . . . . . . . . . .43
PLAYING AN MP3 DISC AT
RANDOM . . . . . . . . . . . . . . . . . . . .44
C SETTINGS . . . . . . . . . . . . . . . . . . .44
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE .44
CHANGING THE SUBTITLE
LANGUAGE . . . . . . . . . . . . . . . . .45
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures) . . . .45
CHANGING THE ON-SCREEN
DISPLAY . . . . . . . . . . . . . . . . . . . .46
C CHANGING THE SETUP ITEMS .47
LANGUAGE SETTINGS . . . . . . . .47
DISPLAY SETTINGS . . . . . . . . . . .48
AUDIO SETTINGS . . . . . . . . . . . .49
PARENTAL LOCK . . . . . . . . . . . . .50
C LANGUAGE CODE LIST . . . . . . . .51
C TROUBLESHOOTING GUIDE . . .52
C MAINTENANCE . . . . . . . . . . . . . . .55
DISC HANDLING . . . . . . . . . . . . .55
C SPECIFICATIONS . . . . . . . . . . . . .56
C WARRANTY . . . . . . . . . . .Back Cover
EN
1C29
TD503_01-36 02.2.26 10:09 AM Page 7
FEATURES
TV/VCR
• Hi-Fi system–The Hi-Fi stereo recording system
• 2 Step picture search operation–You can view a
•
• Three different playback tape speeds : SP/LP/SLP
• Two different recording tape speeds : SP/SLP
• Auto Head Cleaner–Automatically cleans video
•
•
offers you excellent sound quality with a dynamic
range of 80dB, frequency response from 20Hz to
20kHz, and 0.005% wow and flutter.
Rotary 4-head Record/Playback System–Four heads
ensure excellent picture quality and special effects playback.
Index Search–Fast-forwards to start of next recording.
Slow Motion–View recorded program at slower
than normal speed.
• Infrared remote control
• Trilingual on screen tv/vcr setup display selec-
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
heads as you insert or remove a cassette.
• Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
• Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
table in English or Spanish or French
• Real time counter–This shows the elapsed recording
• Digital Auto Tracking (DTR)–Automatically
or playback time in hours, minutes, and seconds. The
“–” indication will appear when the tape is rewound
further than the tape counter position “0:00:00”.
adjusts the tracking for each tape you play.
• Rental play mode–Improves playback picture
• 181 channel capability PLL frequency synthesiz-
•
be necessary to view scrambled cable channels.)
•
er tuner with direct station call–(A converter may
• Auto Clock Setting–Allows you to set the clock
•
•
function from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or
text display added to the program.
Auto power on and off system–Automatically
turns on the TV/DVD/VHS when you insert the
cassette, turns off after auto-rewind, and ejects
when the beginning of the tape is reached.
•
• 1 Year, 8 events (including Daily and Weekly
• Auto rewind when the end of a tape is
reached–This function doesn’t occur when using
timer recording.
• Smooth mode change–TV/VCR mode, DVD
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Let you set the TV/DVD/VHS to
advance the tape by entering the desired playback
time you want to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
•
mode automatically changes without control.
•
•
-7-
Timer Recording)–The built-in timer allows you to
record up to 8 programs at different times on different channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Auto return–After timer recording is finished, the
TV/DVD/VHS can return to the beginning of the
recording.
Sleep timer–Allows you to have the TV/DVD/VHS
automatically turn on or off at a desired time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
EN
1C29
TD503_01-36 02.2.26 10:09 AM Page 8
DVD
¡Dolby Digital surround
This player can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby Digital
decoder.
¡Still/fast/slow/step playback
• Sleep timer
Allows you to have the TV/DVD/VHS automatically
turn off at a desired time.
¡DTS (Digital Theater System)
You can enjoy 5.1channel surround system developed by
the Digital Theater System co. which reproduces the original sound as truthfully as possible.
Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in
random order.
¡Search
Chapter search: Search for the chapter designated by user
is possible.
Title search:
Search for the title designated by user is
possible.
Track search: Search for the track designated by user is
possible.
Time search: Search for the time designated by user is
possible.
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in any
desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language, if
available on a DVD.
¡Screen saver/Auto power-off functions
¡Repeat
Chapter:
Repeated playback of the chapter of the
disc being played is possible.
Title:
Repeated playback of the title of the disc
being played is possible.
Track:
Repeated playback of the track of the disc
being played is possible.
Disc(audio CD): Repeated playback of the entire disc being
(MP3)
played is possible.
A-B:
The part between A and B designated by
user is possible.
Album:
Repeated playback of the folder of the
MP3 disc being played is possible.
The screen saver program starts when there is no input
from the player for five minutes in the stop mode. When
the screen saver program is activated for 30 minutes, the
DVD power is automatically turned off, and "DVD"
appears on the screen.
¡Subtitles in a desired language
You can select a desired language for the display subtitles,
if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc contains
sequences recorded from different angles.
¡Zoom
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available on a
disc.
¡Parental lock
You can set the control level to limit playback of discs
which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if a loaded disc is DVD,
audio CD or MP3 on disc.
¡Playing an MP3 disc
You can enjoy MP3 files which are recorded on CDR/RW.
¡Direct Search
You can search the desired title, chapter, and track with
numeric button during playback or in stop mode.
2-time and 4-time magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which the
play was stopped.
¡SRS TruSurround
You can enjoy stereophonic virtual space on your existing
stereo system.
¡Dimmer
Brightness of the display can be varied.
¡Bit rate indication
¡DRC (Dynamic range control)
¡On-screen display
This unit employs TruSurround system
Information about the current operation can be displayed
on a TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
of SRS Labs, Inc. as virtual
technology.
TruSurround and the
SRS Labs, Inc.
symbol are trademarks of
TruSurround technology is incorporated under license
from SRS Labs, Inc.
NOTE:
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
-8-
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 9
OPERATING CONTROLS AND FUNCTIONS
- TV/DVD/VHS FRONT PANEL - [Fig.1]
DVD buttons
POWER
VOLUME
SKIP
PLAY
SKIP
STOP
TV/VCR buttons
OPEN/CLOSE
SELECT
CHANNEL
REC/OTR
REW
PLAY
F.FWD STOP/EJECT
AUDIO
HEADPHONE VIDEO
DVD
SEARCH
1
2
3 4 3
- REMOTE CONTROL -
POWER PICTURE
1
22
23
1
2
3
4
5
6
7
8
27
28
29
30
31
32
33
SPEED
0
+10
C.RESET
ZOOM
45
44
CH.
11
VOL.
2
MUTE
PLAY
DISC
MENU
DISPLAY
ENTER
SETUP
TITLE
RETURN
CLEAR SEARCH MODE REPEAT
A-B
AUDIO
ANGLE
MODE
SUBTITLE
R
7 8 9 10 11 12 13 14 4 15 16 17 18 19 20 21
SELECT
STOP
RECORD
6
[Fig. 2]
9
+100
PAUSE
24
25
26
(DVD) 3
(TV/VCR) 14
4
13
SLEEP
5
L
TV/VCR
43
42
3 (DVD)
15 (TV/VCR)
5
41
40
39
38
37
36
35
34
1. POWER button [TV/VCR P.15 / DVD P.37]
Press to turn the power on and off.
2. VOLUME X/Y buttons
Press to control the volume level for the DVD and TV.
3. SKIP buttons (for DVD)[P.37]
Skip chapters or tracks to a desired point.
4. PLAY button [TV/VCR P.26 / DVD P.37]
Starts playback of the disc or tape contents.
5. STOP button [P.37]
Stops operation of the disc.
6. OPEN/CLOSE button [DVD P.37]
Press to insert discs into or remove them from the
tray.
7. Disc loading tray
8. DVD indicator
Lights on during DVD mode.
9. SELECT button
Press to change to TV/VCR mode or DVD mode.
NOTE: For about 4 seconds just after the DVD
mode has switched to the TV mode, the button
does not work to switch back to the DVD mode.
10. TV/VCR indicator
Lights on during TV/VCR mode.
11. CHANNEL K/L buttons
Press to select memorized channel.
12. Recording indicator
Flashes during recording. Lights up in the Standby mode for Timer Recording.
13. REC/OTR (RECORD) button [TV/VCR P.28]
Press for manual recording. Activates One Touch
Recording. (OTR is only during TV/VCR mode.)
14. REW button (for TV/VCR) [TV/VCR P.26]
Press to rewind the tape, or to view the picture
rapidly in reverse during playback mode. (Rewind
Search)
15. FWD button (for TV/VCR) [TV/VCR P.26]
Press to rapidly advance the tape, or to view the
picture rapidly in forward during playback mode.
(Forward Search)
16. STOP/EJECT button [TV/VCR P.28]
Press to stop the tape motion. Press in the Stop
mode to remove tape from the unit.
17. Remote sensor window
18. HEADPHONE jack
To connect headphone (not supplied) for personal
listening.
19. VIDEO input jack
Connect to the video output jack of a video
camera or VCR.
-9-
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 10
- TV/DVD/VHS REAR PANEL - [Fig.3]
ANT.
1
L
AUDIO OUT
R
COAXIAL
46
47
20. AUDIO L/R input jacks
Connect to the audio output jacks of a video
camera or VCR.
21. Cassette compartment
22. PICTURE button
Press to adjust the picture.
23. Number buttons
48 49
31. MODE button [DVD P.41]
Activates program playback or random playback mode.
32. SEARCH MODE button [DVD P.39]
Press to locate a desired point.
33. AUDIO button [DVD P.44]
Press to select a desired audio language or sound
mode.
34. SUBTITLE button [DVD P.45]
Press to select a desired subtitle language.
35. REPEAT button [DVD P.40]
Repeats playback of the current disc, title, chapter
or track.
36. ANGLE button (DVD mode) [DVD P.45]
Press to change the camera angle to see the
sequence being played back from a different angle.
37. A-B REPEAT button [DVD P.40]
Repeats playback of a selected section.
38. RETURN button
Returns to the previous operation.
39. ENTER button
Press to accept a setting.
40. Arrow buttons
TV Mode:[P.15]
Press two digits to directly access the desired
channel.
Remember to press a "0" before a single digit
channel.
+100 button–
Press to select cable channels which are equal or
greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 button–
Press to enter the desired numbers which are
equal or greater than number 10.
24. PAUSE button [TV/VCR P.26 / DVD P.38]
Pauses the current disc or tape operation.
25. SPEED button [TV/VCR P.30]
Press to choose the desired recording speed:
SP/SLP.
26. C.RESET button [TV/VCR P.28]
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program. (See
page 33.)
27. DISPLAY button
TV/VCR Mode:
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the
display on a TV screen.
TV/VCR Mode:
Display the counter or the current channel number
and current time on the TV screen.
DVD Mode:[P.43]
Displays the current status on the TV screen for
checking purposes.
28. SETUP button [TV/VCR P.15]
Press to enter or exit the TV menu or DVD setup
mode.
29. TITLE button [DVD P.37]
Displays the title menu.
30. CLEAR button
Resets a setting.
41. DISC MENU button [DVD P.37]
Displays the menus in the DVD.
42. ZOOM Button [DVD P.42]
Enlarges part of a DVD-reproduced image.
43. MUTE button
Mutes the sound. Press it again to resume sound.
44. SLEEP button [TV/VCR P.34]
Sets the Sleep Timer. (See page 34.)
45. SELECT button
Press to switch TV/VCR and DVD mode. You can
see the mode (TV/VCR or DVD) on the front
panel indicator.
- 10 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 11
46. ANT. in jack
Connect to an antenna, cable system, or satellite
system.
47. Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect
to a standard AC outlet.
48. COAXIAL digital audio out jack
Connect to the digital input of an external
amplifier or decoder.
49. AUDIO L/R output jack
Connect to the analog audio input of an external
amplifier or decoder.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
VHF/UHF Antenna
(Not supplied)
Satellite Box or
Cable Box (Not supplied)
OUT
From Cable
System
From Cable System or
Satellite Dish
IN
75-ohm
Coaxial
Cable
(Not supplied)
UHF Antenna
(Not supplied)
or
ANT.
1
L
AUDIO OUT
R
COAXIAL
75-ohm Coaxial
Cable (Not
supplied)
VHF Antenna (Not supplied)
VHF/UHF
Combiner
(Not supplied)
ANT.
or
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/DVD/VHS without a converter
box.
By using this connection you can:
1) Use the TV/DVD/VHS remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This unit will ONLY record and view the
same channel.
[Fig. 4]
or
Flat twin-lead cable
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in the ilustration.
By using this connection you can also record scrambled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/DVD/VHS Remote Control. Unattended timer
recording is limited to one channel at a time.
Antenna/Cable Connections
Continued on the Next Page.
- 11 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 12
TO RECORD A SCRAMBLED/UNSCRAMBLED CHANNEL
1. Set the TV/DVD/VHS channel selector to the output channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building as close to the point of cable
entry as practical.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another
source (VCR or video camera), use the audio/video
input jacks on the front of the TV/DVD/VHS.
Connect the audio/video output jacks of another
source to the AUDIO L/R and VIDEO jacks of this
TV/DVD/VHS.
Then press the CHANNEL K/L buttons until "AUX"
appears on the screen.
NOTE:
• When you connect a monaural VCR (another
source) to this TV/DVD/VHS, connect the Audio
output jack of the monaural VCR (another source)
to the AUDIO L jack of this TV/DVD/VHS. The
audio will output in both L and R channel equally.
When using an external input signal (another VCR or
video camera), connect the player’s audio/video output cables to the AUDIO L/R IN/
AUX
VIDEO IN jacks of your
TV/DVD/VHS. Then press the
CHANNEL K or L button until
“AUX” appears on the screen.
To the audio
output jacks
[Another source]
HEADPHONE VIDEO
L-AUDIO-R
Audio/Video
cable
(not supplied)
etc.
To the video
output jack
[Front of the
TV/DVD/VHS]
[Fig. 5]
- 12 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 13
CONNECTING TO A STEREO SYSTEM (for DVD)
ANT.
1
L
AUDIO OUT
Stereo system
R
COAXIAL
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUT jacks
(only DVD AUDIO OUT)
[Fig. 6]
NOTES:
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the
TV/DVD/VHS.
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cables (not included) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or Dat Deck.
ANT.
1
L
AUDIO OUT
R
COAXIAL
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 7]
NOTES:
• The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.
• Set Dolby Digital and DTS to OFF for audio output in the setup mode. Playing a TV/DVD/VHS using
incorrect settings may generate noise distortion, and may also damage the speakers.
• When Dolby Digital is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and you
select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.
- 13 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 14
CONNECTING TO A DOLBY DIGITAL DECODER,
DTS DECODER, OR MPEG DECODER (for DVD)
If using this TV/DVD/VHS to play back a TV/DVD/VHS in a 5.1 channel Dolby Digital surround, DTS surround, or MPEG surround format, the TV/DVD/VHS outputs a Dolby Digital, DTS, or MPEG data stream
from its COAXIAL DIGITAL AUDIO OUT jack. By hooking the player up to a Dolby Digital or DTS
decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound
of a professional standard such as can be heard in movie theaters.
Use an audio coaxial digital cables (not included) for the audio connections.
Front speaker
(left)
Center
speaker
Front speaker
(right)
ANT.
1
L
AUDIO OUT
R
COAXIAL
Dolby Digital
or DTS decoder
Surround
speaker
(left)
To COAXIAL DIGITAL
AUDIO INPUT jack
Surround
speaker
(right)
Subwoofer
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
Center
Center
speaker for
speaker for
MPEG (left) MPEG (right)
[Fig. 8]
NOTES:
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner’s Manuals for the components to be connected to the TV/DVD/VHS.
• If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio
output in the setup mode.
• If output DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode.
• If played a disc indicated MPEG audio, connect to a MPEG decoder, and set MPEG to ON for audio output
in the setup mode.
• Unless connected to a Dolby Digital decoder, a DTS decoder, or a MPEG decoder, set Dolby Digital, DTS,
or MPEG to off for audio output in the setup mode. Playing a TV/DVD/VHS using incorrect settings may
generate noise distortion, and may also damage the speakers.
• When Dolby Digital is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and you
select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
- 14 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 15
TV/VCR SECTION
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/DVD/VHS channel selector to the output channel of the cable box or satellite box (Ex CH3).
Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
Plug in the TV/DVD/VHS power cord
Plug the TV/DVD/VHS power cord
into a standard AC outlet.
NOTE:
• If some digits appear in the corner of
the screen, press the POWER button
without unplugging the power cord.
2
1
Turn on the TV/DVD/VHS
Press the POWER button to turn on the TV/DVD/VHS.
3
“FRANÇAIS”
4
2
Select “ENGLISH” or “ESPAÑOL” or
Select “ENGLISH” or
“ESPAÑOL”=Spanish or
“FRANÇAIS” =French using the
Arrow B or s button. “[ ]” indicate the selected language.
FRA
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
AUTO PRESET
3
Begin auto preset
– SET UP –
Press the Arrow K or L button to
point to “AUTO PRESET”.
Then press the Arrow B button.
The tuner scans and memorizes all
active channels in your area.
NOTES:
• The TV/DVD/VHS distinguishes between standard
TV channels and cable channels.
• If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
SETUP button on the remote control. To preset the
tuner again, see “CHANNEL SET UP AGAIN” on
page 16.
• The TV/DVD/VHS may memorize TV channels as
CATV channels if reception conditions is poor. If
this happens, try AUTO MEMO action again when
reception conditions are better.
LANGUAGE
[ENGLISH] ESP
FRA
B AUTO PRESET
5
Select “ADD/DELETE CH”
Press the Arrow K or L button to
point to “ADD/DELETE CH”.
Press the Arrow B button.
– SET UP –
B LANGUAGE
[ENGLISH] ESP
Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “CHANNEL SET UP”.
Then, press the Arrow B button.
After scanning
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote
control number buttons or CHANNEL K or L.
Enter the desired channel number
Press the Arrow K or L button until
your desired channel number
appears. (You can also use the number buttons or the CHANNEL K/L
button to enter it) (Example: CH8)
4
08
ADD / DELETE
Delete (or add) it from (into) memory
Press the Arrow B or s button. The channel number
changes to light red. The channel is deleted from
memory.
• To delete another channel, repeat steps [3] and [4].
• If you press the Arrow B or s button again, the
channel is memorized again.
5
Exit the channel setup mode
Added channel: Light blue.
Deleted channel: Light red.
Press the SETUP button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL K or L button.
- 15 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 16
CHANNEL SET UP AGAIN
Make sure ...
• Press the POWER button to turn on the
TV/DVD/VHS.
1
Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “CHANNEL SET UP”.
Then, press the Arrow B button.
2
Begin auto preset
– CHANNEL SET UP –
Press the Arrow K or L button to
point to “AUTO PRESET”.
Then, press the Arrow B button.
The tuner scans and memorizes all
the active channels in your area.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
ADD / DELETE CH (TV)
B AUTO PRESET
After scanning
NOTE: If Spanish or French is selected accidentally,
press the SETUP button on the remote control, press
the Arrow K button to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE” [FRANÇAIS], then
press the Arrow B button, then press the SETUP
button on the remote control.
DAYLIGHT-SAVING TIME
Select this feature and the TV/DVD/VHS’s clock
automatically will advance one hour in April, then
reverse one hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
• First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
• Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
• Press the POWER button to turn on the
TV/DVD/VHS.
The tuner stops on the lowest memorized channel.
SELECTING THE LANGUAGE
Make sure ...
• Press the POWER button to turn on the
TV/DVD/VHS.
NOTE: This function effects only the language on
the screen menu and not the audio source.
1
Select “LANGUAGE”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “LANGUAGE”.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
1
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “SETTING CLOCK”.
Then, press the Arrow B button.
2
Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the Arrow B or s
button.
3
Exit the Language mode
Press the SETUP button on the remote control to
return to TV mode.
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the Arrow K or L button to
point to “D.S.T.”.
Then, press the Arrow B or s button until [ON] appears.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
MANUAL CLOCK SET
B D.S.T.
3
2
Select “SETTING CLOCK”
[ON]
Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the Arrow
B or s button.
- 16 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 17
CLOCK SET UP
(AUTO / MANUAL)
2
Set the clock accurately for proper automatic timer
recording. If the Public Broadcasting Station (PBS) is
available in your area, follow “AUTO CLOCK SETTING”. If it is not, follow “MANUAL CLOCK SETTING”.
AUTO CLOCK SETTING
Make sure ...
• TV/DVD/VHS power must be turned on.
• Confirm that the antenna connections are correct.
• The cable converter box must be turned on if your
TV/DVD/VHS is connected directly to it. (See
NOTES:)
• The channel is properly set in advance. (See page
16.)
Select “SETTING CLOCK”
[ON]
AUTO CLOCK CH
[AUTO]
MANUAL CLOCK SET
D.S.T.
3
[OFF]
Enter the channel number for the PBS station
Press the Arrow K or L button to
point to “AUTO CLOCK CH”.
Then press the Arrow B or s button until the channel number for
your local PBS station appears.
If you do not know the PBS channel number, leave it
set to [AUTO] which is located before [2]. The
TV/DVD/VHS will search automatically all available
channels for the local PBS station, and will select
that channel.
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
MANUAL CLOCK SET
B D.S.T.
4
[OFF]
Exit the Auto Clock Setting
Press the SETUP button on the remote control to
return to TV mode.
5
Turn off the TV/DVD/VHS
Turn the TV/DVD/VHS off. Because the Auto Clock
functions automatically while the TV/DVD/VHS is
off.
NOTES:
• Auto clock setting only needs to be set once. But it
can be done again if the clock’s time has become
incorrect for some reason.
• If the TV/DVD/VHS is connected directly to a
cable converter box or satellite box, the local PBS
station must be selected on the cable box itself, and
the TV/DVD/VHS must be set to the output channel of the cable converter box or satellite box (usually channel 3 or 4), to be able to set up or correct
the clock automatically.
If you do not know what your local PBS station is,
then follow “Manual Clock Settings” on page 18.
The TV/DVD/VHS cannot control the channels of
the cable converter box or satellite box.
1
Press the Arrow B or s button
repeatedly until [ON] appears.
– SETTING CLOCK –
B AUTO CLOCK
– SETTING CLOCK –
You can have the TV/DVD/VHS set the clock automatically by using the Public Broadcasting Station
(PBS) channel in your area. Once you have set the
clock by using the following procedure, the
TV/DVD/VHS will automatically monitor the correct
time and date being broadcast by the PBS station in
your area, using a new service called Extended Data
Service (XDS).
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “SETTING CLOCK”.
Then, press the Arrow B button.
Set “AUTO CLOCK” to [ON]
If you choose [AUTO],
• the TV/DVD/VHS must search until the PBS channel is found. It must scan each channel for a couple
of seconds to determine if that channel is transmitting the XDS signal.
• if the time, that is automatically set by this selected
PBS station is incorrect, it may not be your local
PBS station, but one from a different time zone. Or
there is a case that no channel is broadcasting the
XDS signal in your area, as shown by no time. In
these cases, you must manually enter the correct
local PBS station, or set the clock manually and
turn off the Auto Clock Setting feature.
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- 17 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 18
MANUAL CLOCK SETTING
Make sure ...
• TV/DVD/VHS power must be turned on.
1
Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “SETTING CLOCK”.
Then, press the Arrow B button.
In the example below, the clock is to be set to:
DATE
May 7th, 2002
SETTING TIME 5:40PM
6
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
7
2
Select “MANUAL CLOCK
SET”
Press the Arrow K or L button to
point to “MANUAL CLOCK SET”.
Then, press the Arrow B button.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
Select the hour
Press the Arrow K or L button until
your desired hour appears.
(Example: 5, PM)
Then, press the Arrow B button.
Select the minute
Press the Arrow K or L button until
the desired minute appears.
(Example: 40)
– MANUAL CLOCK SET –
MONTH DAY
05 / 07
HOUR
YEAR
TUE
2002
MINUTE
05 : ––
PM
– MANUAL CLOCK SET –
MONTH DAY
05 / 07
HOUR
YEAR
TUE
2002
MINUTE
05 : 40
PM
B MANUAL CLOCK SET
D.S.T.
[OFF]
8
Start the clock
5:40 PM
3
Select the month
Press the Arrow K or L button until
your desired month appears.
(Example: May → 05)
Then, press the Arrow B button.
4
Select the day
Press the Arrow K or L button until
your desired day appears.
(Example: 7th → 07)
Then, press the Arrow B button.
5
– MANUAL CLOCK SET –
MONTH DAY
05 / ––
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
– MANUAL CLOCK SET –
MONTH DAY
05 / 07
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
TO CHANGE CLOCK SETTING
Select the year
Press the Arrow K or L button until
your desired year appears.
(Example: 2002)
Then, press the Arrow B button.
Press the SETUP button on the
remote control.
Although seconds are not displayed,
they begin counting from 00 when
you press the SETUP button on the
remote control. Use this feature to synchronize the
clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 30 seconds, you may have to
reset the clock.
– MANUAL CLOCK SET –
MONTH DAY
05 / 07
HOUR
YEAR
TUE
MINUTE
–– : ––
––
2002
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the Arrow
B or s button.
3)Enter correct numbers using the Arrow K or L
button.
4)Press the SETUP button on the remote control to
start the clock.
PLEASE NOTE:
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the Arrow B or s button to turn [OFF] this
function. Then you can manually adjust the clock.
- 18 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 19
TV OPERATION
WATCHING A TV PROGRAM
1
PICTURE CONTROL
Turn on the TV/DVD/VHS
Press the POWER button to turn on the
TV/DVD/VHS.
2
Select the channel number
Press the CHANNEL K or L button to select your
desired channel number or press the number buttons
on the remote control.
Remember: If the TV/DVD/VHS is connected to a
cable box or satellite box, the TV/DVD/VHS must be
on CH3 or CH4, then the channel to be viewed must
be selected on the cable box or satellite box.
3
The TV/DVD/VHS’s picture controls – BRIGHT,
CONTRAST, COLOR, TINT and SHARPNESS –
are preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
• Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
• When setting the Picture Control, the Game mode
will be cancelled.
Make sure ...
• TV/DVD/VHS power must be turned on.
1
Adjust sound
Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
Press the VOLUME X or Y button
to adjust the volume.
VOLUME
20
C C C C C CCCCCCC
2
NOTES:
• If you press the CHANNEL o or p in the DVD
mode, you can change the TV channels.
Even if you turn off the TV/DVD/VHS in the DVD
mode, when you turn it on again, it will go into the
TV/VCR mode.
BRIGHT
–PPPPPPPCPPPPPPP+
DEGAUSSING
3
Magnetism from nearby appliances might affect the
color of the TV picture.
If this happens, move this unit away from the appliance. If the color is still not correct, disconnect power
cord from AC outlet then reconnect it after 30 minutes.
Select item you want to adjust
Press the Arrow K or L button until desired control
is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
Adjust the picture control
Press the Arrow B or s button to adjust to your
desired level.
COLOR
Arrow s
to decrease
brightness
to decrease
contrast
to pale
Arrow B
to increase
brightness
to increase
contrast
to brilliant
TINT
SHARPNESS
to purple
to soft
to green
to clear
BRIGHT
CONTRAST
• If there is a power failure of any kind, the unit will
retain its memory for this feature.
- 19 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 20
CLOSED CAPTION SYSTEM
1
You can view specially labeled (cc) TV programs,
movies, news, pre-recorded tapes with either a dialogue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
NOTE:
Not all programs are broadcast with closed captions.
Your television is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
• Automobile ignition noise
• Electric motor brush noise
• Weak snowy reception on TV screen
• Multiplex signal reception displaying picture
ghosts or airplane flutter.
• Playback of poorly recorded or worn VCR tapes.
NOTE:
If the TV/DVD/VHS displays a
black box on the TV screen, this
means that the TV/DVD/VHS is set
to the TEXT mode. To clear screen,
select [CAPTION1], [CAPTION2]
or [OFF].
Make sure ...
• TV/DVD/VHS power must be turned on.
Select “CAPTION”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “CAPTION”.
2
Select your desired caption menu
Press the Arrow B or s button
until your desired caption menu
appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Exit the caption setting mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button. Press the SETUP button on
the remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 seconds.
• This is also true when the MUTE button is pressed,
and when the PAUSE button is pressed while
recording.
• If there is a power failure of any kind, the unit will
retain its memory for this feature.
- 20 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 21
V-CHIP SET UP
V-CHIP enables parents to prevent their children
from watching inappropriate material on TV.
V-CHIP reads the ratings for programming (except
for news and sports programs, unedited movies on
premium cable channels, and Emergency Broadcast
System signals), then denies access to programming
if the program’s rating meets the limitations you
select. In this case, “PROTECTED PROGRAM by
...” message appears on the TV screen. You can
watch the protected program by entering access code
(default 0000).
To block ratings, follow the steps below.
• Programming may be rated by the Motion Picture
Association of America (MPAA) or according to
the Television Parental Guidelines. In order to
block any inappropriate programming, set your
limits in both places (MPAA RATING and TV
RATING).
TV RATING SET UP
Make sure ...
• TV/DVD/VHS power must be turned on.
1
Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “V-CHIP SET UP”.
Then, press the Arrow B button.
2
Input Access code
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
ACCESS CODE
Use the number buttons to enter 4digit access code. The default code
is 0000.
3
Select “TV RATING”
Press the Arrow K or L button to
point to “TV RATING”.
Then, press the Arrow B button.
4
• When you select the rating category and turn it
•
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “TV-Y” to [VIEW], the all ratings
will turn to [VIEW] automatically.
Selection
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
Rating Category Explanations
Appropriate for all children
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
TV-MA
Mature audience only
When you select TV-Y7, TV-PG, TV-14, or TV-MA
and you press the Arrow B button, the sub-ratings
will appear on the TV screen.
If you select the rating category (example: TV-PG)
and turn it [BLOCK] or [VIEW], the sub-ratings
(example: V for Violence) will turn [BLOCK] or
[VIEW] automatically.
You can set the sub-ratings to [BLOCK] or [VIEW]
individually when the rating category is set to
[BLOCK].
To set the sub-ratings individually, follow the steps
below.
• When you select [TV-Y7]:
Press the Arrow L or K button to
select “FV” (Fantasy Violence).
Then, press the Arrow B button
to select [BLOCK] or [VIEW].
• When you select [TV-PG], [TV-14] or [TV-MA]:
Press the Arrow L or K button to
select “D”(Suggestive Dialog),
“L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
Arrow B button to select
[BLOCK] or [VIEW].
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
• The sub-ratings which set to
[BLOCK] appears next to the rating category in the TV RATING
menu.
TV–Y7
B FV
TV–PG
_ _ _ _
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
[BLOCK]
[BLOCK]
[BLOCK]
B D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
B TV–Y
TV–Y7 (
)
TV–G
TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Select your desired item
Press the Arrow K or L button to
point to your desired item.
Then, press the Arrow B button to
select [BLOCK] or [VIEW].
B TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
)
)
)
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
return to original mode.
- 21 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 22
MPAA RATING SET UP
CHANGE ACCESS CODE
Make sure ...
• TV/DVD/VHS power must be turned on.
To change access code, follow the steps.
1
1
Select “V-CHIP SET UP”
- TV/VCR SETUP -
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “V-CHIP SET UP”.
Then, press the Arrow B button.
2
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “MPAA RATING”
Selection
G
PG
PG-13
R
3
_ _ _ _
Use the number buttons to enter 4digit access code. The default code
is 0000.
ACCESS CODE
_ _ _ _
– V-CHIP SET UP –
TV RATING
B MPAA RATING
CHANGE CODE
4
Press the Arrow K or L button to
point to "CHANGE CODE". Then,
press the Arrow B button.
NC-17
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompanying parent or adult guardian
No one under 17 admitted
X
Mature audience only
5
Select your desired item
Press the Arrow K or L button to
point to your desired item.
Then, press the Arrow B button to
select [BLOCK] or [VIEW].
• When you select the rating category and turn it [BLOCK], the higher rating will
turn [BLOCK] automatically. Also, the lower rating will turn [VIEW] automatically.
• When you turn “G” to [VIEW], the all ratings will
turn to [VIEW] automatically.
G
PG
PG–13
B R
NC–17
X
5
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
ACCESS CODE
Press the Arrow K or L button to
point to “MPAA RATING”.
Then, press the Arrow B button.
4
2
Press the Arrow K or L button to
point to "V-CHIP SET UP". Then,
press the Arrow B button.
Use the number buttons to enter 4digit access code. The default code
is 0000.
3
Press the SETUP button so that the TV/VCR SETUP
display appears on the TV screen.
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
• If you enter wrong code, repeat
step 5, making sure you enter the
same new code exactly in the
confirm code space.
– V-CHIP SET UP –
TV RATING
MPAA RATING
B CHANGE CODE
NEW CODE
_ _ _ _
CONFIRM CODE
_ _ _ _
NEW CODE
XXXX
CONFIRM CODE
_ _ _ _
6
Press the SETUP button to exit the TV/VCR SETUP.
Note:
• If you unplug the power code or power failure
occures, the changed access code will be lost and
will return to default (0000). Change your access
code again as necessary.
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
return to original mode.
- 22 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 23
MTS(Multi-Channel Television sound)SYSTEM
You can record or listen to a program in MTS stereo.
CHECKING THE SELECTED MTS MODE
When you play a VHS tape, or receive a broadcast
on the TV/DVD/VHS tuner channel you are watching,
the status shown below will appear when you press
the DISPLAY button on the remote control.
4]
PLAY B
HIFI
12:00AM
CH 123
STEREO/SAP
3]
2]
1]
SP
COUNT
0:00:00
SAP
Second Audio Program, which means your
program, can also be received in a second
language or sometimes a radio station.
HIFI
High Fidelity which produces better sound
than standard stereo TV/DVD/VHSs.
1] When a program is broadcast in stereo, STEREO
appears on the TV screen.
2] When a program is broadcast in second audio,
SAP appears on the TV screen.
3] When a program broadcast both in stereo and second audio, STEREO and SAP appear on the TV
screen.
NOTE: Although a program may be broadcast in
both stereo and second audio, you cannot
record in both stereo and second audio at
the same time.
4] While the TV/DVD/VHS is set in HIFI stereo
mode and playback mode. HIFI appears on the
TV screen. While the TV/DVD/VHS is set in
monaural(MONO) mode, HIFI disappears from
the TV screen.
NOTE: If you play non-HIFI tapes while the
TV/DVD/VHS is set in HIFI, HIFI will disappear from the TV screen and the
TV/DVD/VHS will play automatically in
monaural.
MTS RECORDING/MONITOR MODE
Type of broadcast
Regular
(monaural audio)
Stereo broadcast
Bilingual broadcast
Display on
the TV screen
-None-
STEREO/SAP
SELECTION
-Invalid-
STEREO
SAP
-InvalidSTEREO*
L
Main audio
program
Sub audio
program
L
sub audio
program
SAP*
Stereo & Bilingual
broadcast
STEREO
SAP
Hi-Fi audio track(2-channel)
L-channel
R-channel
Mono
Mono
STEREO*
SAP*
R
Main audio
program
Sub audio
program
R
sub audio
program
Normal audio
track
Mono
L+R
Main audio
program
Sub audio
program
L+R
sub audio
program
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 23 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 24
SELECTING THE MTS SYSTEM
TO SELECT MONO MODE
Make sure ...
• TV/DVD/VHS power must be turned on.
TO SELECT HIFI MODE
1
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “USER’S SET UP”. Then,
press the Arrow Bbutton.
2
Select“VCR AUDIO”
Press the Arrow K or L button to
point to“VCR AUDIO”. Then, press
the Arrow Bbutton.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
You can change the selection to “MONO” if you
want to listen to HIFI tapes in normal audio playback.
1) Press the SETUP button on the remote control.
Press the Arrow K or L button to point to
“USER’S SET UP”.Then, press the Arrow B
button.
2) Press the Arrow K or L button to point to
“VCR AUDIO”. Then, press Arrow Bbutton.
3) Press the Arrow B or s button until [MONO]
appears.
4) Press the SETUP button on the remote control to
return to TV mode.
TO SELECT STEREO, SAP, OR MONO
1
3
Select [HIFI]
Press the Arrow B or s button
until [HIFI] appears.
4
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
Select “USER’S SET UP”
Press the “SETUP” button on the
remote control.
Press the Arrow K or L button to
point to “USER’S SET UP”.Then,
press the Arrow B
button.
2
To return to TV mode
Select “TV AUDIO”
Press the Arrow K or L button to
point to“TV AUDIO”. Then, press
the Arrow Bbutton.
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
• Normally, “HIFI” should be selected for playbackwith HIFI sound.
• When you play non-HIFI tapes, the TV/DVD/VHS
will play automatically in the monaural mode.
• The TV/DVD/VHS records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
B TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
Select [STEREO], [SAP], or [MONO]
Press the Arrow B or s button until [STEREO],
[SAP], or [MONO] appears.
4
To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
• You must select the recording mode,either TV
AUDIO [STEREO] or [SAP] when you record a
broadcast.
Refer to “MTS RECORDING/MONITOR MODE”.
• If you select second audio when second audio is not
available, the TV/DVD/VHS will record normal
audio.
- 24 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 25
VIDEO CASSETTE
This TV/DVD/VHS will operate with any cassette that has the
mark. For best results,
we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
• Avoid moisture. Moisture condensation may occur
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/DVD/VHS. The
TV/DVD/VHS will automatically turn on.
•
•
•
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/DVD/VHS, wait until the tape has
warmed to room temperature and the moisture has
evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
Window
WRONG
CORRECT
TWO DIFFERENT TAPE SPEEDS
REMOVING A CASSETTE
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each
mode.
1)In the Stop mode, press the EJECT button on the
remote control or press the STOP/EJECT button on
the TV/DVD/VHS. The cassette will eject.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
Tape Speed
Type of tape
Recording/Playback Time
T60
T120
T160
SP mode
1 hour
2 hours
2-2/3 hours
SLP mode
3 hours
6 hours
8 hours
Note: You can play back a tape recorded in LP mode
(Long Play).
ERASE PREVENTION
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Transparent Tape
NOTE:
• In DVD mode, Whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
you press the PLAY button.
In TV/VCR mode, if th cassette without tab is
inserted, playback will automatically start.
- 25 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 26
PLAYBACK
NORMAL PLAYBACK
Make sure ...
• TV/DVD/VHS power must be turned on.
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/DVD/VHS will start playback automatically.
2
To begin playback
PLAY B
Press the PLAY button.
3
To stop playback
STOP
Press the STOP button when playback is completed.
NOTES:
• If you press the TV/VCR side PLAY button in the
DVD mode, you can start the VCR playback.
• If you press the SELECT button in the VCR
playback, it will stop and the mode will
change to the DVD mode. In addition, the
same function operates with the DVD side
PLAY button or OPEN/CLOSE button.
TRACKING ADJUSTMENT
SLOW MOTION
During pause, press the FWD button to reduce the
playback speed. The TV/DVD/VHS mutes the sound
during slow motion. Press the PLAY button to return
to normal playback.
NOTE: If it is left in the Slow mode for more than
five minutes, the TV/DVD/VHS will automatically
go into the Stop mode.
PICTURE SEARCH
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button. (in the SP / LP / SLP
modes)
NOTE:
• If you press the F.FWD or REW button on the
front panel in the DVD mode, the VCR forward or
reverse will start. Please press the STOP / EJECT
button once to stop it, twice to eject it.
2)Press it again and the TV/DVD/VHS will now
search in super high speed. (in the LP / SLP modes
only)
NOTE:
• Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture
may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
STILL PICTURE
• Tracking adjustment will be set automatically
You can view a still picture on the TV screen during
(Digital Tracking function) when you start playplayback (the Still mode). Press the PAUSE button
back.
during playback. Only tapes recorded in the SLP
• However when playing pre-recorded tapes or tapes mode will show the least amount of lines.Press the
recorded on units other than your own, noise lines
PLAY button to return to playback.
(black and white streaks) may appear on the playNOTES:
back picture. If this occurs, you can adjust the
• You can advance the picture one frame at a time by
tracking control manually by pressing the CHANpressing the PAUSE button during the Still mode.
NEL K or L button until the streaks disappear. To
If it is left in the Pause mode for more than five
•
return to the DTR function, stop the tape once and
minutes, the TV/DVD/VHS will automatically
start playback again.
switch to the Stop mode.
• You can reduce the noise lines by pressing the
CHANNEL K or L button in slow mode, too.
VERTICAL HOLD CONTROL
Tracking adjustment in Slow mode will not be set
automatically.
In the Pause/Still mode only, when the picture begins
NOTE:
to vibrate vertically, stabilize the picture by pressing
• In Still mode, press the SLOW button and press the the CHANNEL K or L button.
CHANNEL K or L button until streaks disappear.
NOTE:
To return to Still mode, press the PAUSE button
If there are video noise lines on the screen, see Tracking
again.
Adjustment section.
- 26 EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 27
SPECIAL PLAYBACK
Make sure ...
• TV/DVD/VHS power must be turned on.
• Insert a prerecorded tape.
• Before playback, follow steps below.
AUTO REPEAT PLAYBACK
The TV/DVD/VHS has the auto repeat function that
allows you to repeat a tape indefinitely without
touching the PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
RENTAL PLAYBACK
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1
2
Set “RENTAL” to [ON]
Press the Arrow K or L button to
point to “RENTAL”.
Press the Arrow B or s button
until [ON] appears.
3
1
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “USER’S SET UP”.
Then, press the Arrow B button.
[ON]
[OFF]
[OFF]
[HIFI]
[STEREO]
3
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button on the remote control. Press
the SETUP button on the remote control to return to
TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
– USER’S SET UP –
RENTAL
B REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[ALL]
[OFF]
[HIFI]
[STEREO]
Exit the Repeat Play setting
Press the SETUP button on the remote control to
return to the TV mode.
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
• Once you select the Rental mode, it stays in effect
even after you turn off the TV/DVD/VHS.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “ALL” or “BLANK”
Press the Arrow K or L button to
point to “REPEAT PLAY”.
Press the Arrow B or s button
repeatedly until your desired selection [ALL] or [BLANK] appears.
Exit the Rental setting
Press the SETUP button on the remote control to
return to the TV mode.
4
2
– USER’S SET UP –
B RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “USER’S SET UP”.
Then, press the Arrow B button.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
4
Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
• Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/DVD/VHS.
• If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button on the remote control. Press
the SETUP button on the remote control to return to
TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
- 27 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 28
SEARCH
Make sure ...
• TV/DVD/VHS power must be turned on.
• Insert a tape.
ZERO RETURN
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1
Reset the counter to 0:00:00
Insert a tape.
2
Select “TIME SEARCH” mode
3
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
4
1
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “TIME SEARCH”.
Then, press the Arrow B button.
Press the COUNTER RESET button repeatedly.
3
is not inserted in the TV/DVD/VHS.
In the example below: To watch a program after 2
hour 50 minutes from the present position, in either
direction.
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2
• This function will not operate in recording mode.
• This function is not operative when a cassette tape
To activate “ZERO RETURN” mode
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “ZERO RETURN”.
Then, press the Arrow B button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter
returns to 0:00:00.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B ZERO RETURN
TIME SEARCH
INDEX SEARCH
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
Enter your desired time
Press the Arrow K or L button until
your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time
Search at this point, press the SETUP button on the
remote control.
TIME SEARCH
2 : 50
4
Begin Time Search
By pressing the Arrow s or B button, the
TV/DVD/VHS will rewind or fast forward to the
specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TIME SEARCH
The Time Search function makes it possible to quickly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
NOTES:
• Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the TV/DVD/VHS
or the remote control. This will delete the selected
time.
- 28 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 29
INDEX SEARCH
1
This feature provides a method of indexing the starting point so that it can be easily returned to in either
fast forward or rewind mode.
• The index mark will be made automatically when
the REC button is pressed. It will also be marked at
the starting point of Timer recording and OTR.
• The index mark will not be recorded if the PAUSE
button is pressed and released during recording.
• The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 minutes for SLP recording.
• In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
CURRENT PLAYBACK PROGRAM
Beginning of tape
Pro.1
4
Pro.2
3
2
2
Pro.4
1
Pro.5
1
Pro.6
2
Enter your desired number
INDEX SEACH
03
3
Begin Index Search
Press the Arrow s or B button. The TV/DVD/VHS
begins rewinding or fast forwarding to the beginning
of desired program.
NOTE: Every time an index signal is skipped, the
number in the program indicator decreases by one.
4
Pro.7
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
Press the Arrow K or L button until
the number of programs that you
want to skip appears.
(Example: “03” for 3 programs)
• The Index Search mode will be
canceled if the procedures are not activated in 30
seconds.
End of tape
Pro.3
Select “INDEX SEARCH”
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “INDEX SEARCH”. Then,
press the Arrow Bbutton
After Index Search
When the preset program is reached, the
TV/DVD/VHS will start playback automatically.
• A video cassette must be inserted in the
TV/DVD/VHS for this function to work.
• The number of Index Searches can be set up to 20.
• This function will not operate in the recording mode.
• When you want to cancel the Index Search while
in progress, press the STOP button.
3
INDEX MARK
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.)The “–” indication will appear when the tape has
rewound further than “0:00:00” on the tape counter.
• When the end of a tape is reached during record-
•
•
- 29 -
ing, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding
finishes, the TV/DVD/VHS will eject the tape and
turn itself to off.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer recording or One Touch Recording.
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 30
RECORDING
Make sure ...
• TV/DVD/VHS power must be turned on.
• Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
• This unit will ONLY record and view the same channel.
• This unit cannot record the contents from the built-in DVD.
SKIPPING UNWANTED
SCENES DURING RECORDING
NORMAL RECORDING
You can ONLY watch the same TV program that is
being recorded.
Press the PAUSE button to temporarily stop recording.
Press the PAUSE or RECORD button to resume recording.
NOTES:
• After five minutes, the
TV/DVD/VHS will automatically switch to the
Recording mode to prevent tape damage.
• If “CLOSED CAPTION (ON)” is selected, the OnScreen Display will appear for 5 seconds, then disappear.
PAUSE
1
Select the channel to be recorded
Press the number buttons on the
CH 10
remote control or the CHANNEL
K or L button.
Remember: If the TV/DVD/VHS is
connected to a cable box or satellite
box, the TV/DVD/VHS must be on CH3 or CH4,
then the channel to be recorded must be selected on
the cable box or satellite box.
2
SP
Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
SP
3
Begin recording
REC
Press the RECORD button.
SP
4
Stop recording
Press the STOP button when recording is completed.
- 30 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 31
OTR (One Touch Recording)
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/DVD/VHS.
Make sure ...
• TV/DVD/VHS power must be turned on.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTES:
• This function CANNOT be done from the remote
control.
• Recording starts immediately when the REC/OTR
button is pressed.
• When the REC/OTR button is pressed 18 times, the
TV/DVD/VHS returns to the Normal Recording
mode.
• To stop the OTR operation, press the STOP button
on the TV/DVD/VHS or on the remote control.
• To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momentarily then disappear.)
• Recording stops when 0:00 is reached.
• Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T120).
• If the tape runs out before the end time, the
TV/DVD/VHS will switch to the Stop mode immediately, ejects the tape and turns itself off.
1
Select the tape speed
Begin OTR
OTR(2 : 30)
Press the REC/OTR button on the
TV/DVD/VHS as many times as
needed. The recording length will
be determined by the number of
times you press the REC/OTR button. Each additional push will increase the recording time by 30 minutes. It is set up to 8 hours.
SP
17 pushes
8:00
0:30
1:00
Recording length
(normal recording)
30 minutes
60 minutes
480 minutes
You can make copies of video tapes made by friends
or relatives for your enjoyment.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your TV/DVD/VHS and a Source (Playing)
VCR using the following diagram.
[Fig.8]
[The TV/DVD/VHS]
HEADPHONE VIDEO
L-AUDIO-R
[Ex: Source (playing)
VCR or camcorder]
AUDIO
Audio/Video
adapter cable
(not supplied)
L
IN
OUT
R
VIDEO
OUT
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3
Display
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL K or L button.
Remember: If the TV/DVD/VHS is connected to a
cable box or satellite box, the TV/DVD/VHS must be
on CH3 or CH4, then the channel to be recorded is
selected on the cable box or satellite box.
2
Push(es)
1 push
2 pushes
3 pushes
IN
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record over, into the TV/DVD/VHS’s cassette compartment.
3)Press the SPEED button on remote control for the
TV/DVD/VHS to select the desired recording
speed (SP/SLP).
4)Press the CHANNEL K or L button on the
TV/DVD/VHS until “AUX” appears on the screen.
5)Press the RECORD button on the TV/DVD/VHS.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/DVD/VHS’s front panel controls whenever possible. The remote control might affect the source
(Playing) VCR’s playback operation.
- 31 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 32
TIMER
AUTOMATIC TIMER
RECORDING
pressing the Arrow K button. And press the Arrow B
button.
• If you have not yet set the clock,
“MANUAL CLOCK SET”
appears. If so, follow stops [3] to
[8] on page 18. Then set the timer
recording.
- TV/VCR SETUP -
You may set the TV/DVD/VHS to start and end a
recording while you are away. You can set 8 programs to record on specific days, daily or weekly
within a 1 year period.
In the example below, the timer is being set to record:
DATE:
July 6th, 2001
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
CH61
TAPE SPEED:
SP
Make sure ...
• If a cable box or satellite box is connected with the
TV/DVD/VHS you will be limited to record only
one channel. And the channel selector on the
TV/DVD/VHS must be selected to the output
channel of the boxes CH 3 or CH 4 and then the
actual channel to be recorded must be selected on
the boxes.
• Clock must be set to the correct time and date
before setting the timer.
• TV/DVD/VHS power must be turn on to program
it.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
• The channel you want to record is properly set in
advance. (See page 16.)
Avoid over lap of programs ...
There is a chance that a program will not be recorded. when programs overlap;
• The program with an earlier start has priority.
• Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
• The illustration below demonstrates the sequence
of recordings.
Program 1
10:00AM - 11:00AM
Program 2
9:00AM - 10:00AM
Program 3
9:30AM - 12:00PM
B TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
position (1~8)
Press the Arrow K or L button to
select the desired program position.
Then, press the Arrow B button.
3
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
1
Set the channel number
– TIMER PROGRAMMING –
CH DATE
B -
-
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
– TIMER PROGRAMMING –
Press the Arrow K or L button until
the desired channel number
appears.
(Example: CH61)
Then, press the Arrow B button.
Remember: If the TV/DVD/VHS is connected to a
cable box or satellite box, the TV/DVD/VHS must be
on CH3 or CH4, then the channel to be recorded is
selected on the cable box or satellite box.
CH DATE
---B 61
-----
4
Select once, every day or
weekly recording
For once recording :
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
-
-
-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 7/06 FRI -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Press the Arrow K (up) button
until the desired date appears.
(Example: “7/06” for July 6th). Then, press the
Arrow B button.
For every day recording : To record a TV program
at the same time on the same channel every day. (Example: Monday
through Sunday)
– TIMER PROGRAMMING –
CH DATE
Press the Arrow L (down) button
until “EVRY DAY” appears.
Then, press the Arrow B button.
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
Select your desired program
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY DAY -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
For weekly recording : To record a TV program at
the same time on the same channel
every week. (Example: every
Monday)
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Press the Arrow L (down) button
until “EVRY” and your desired
day of the week appear together. Then, press the
Arrow B button.
Select “TIMER PROGRAMMING”
Press the SETUP button on the remote control.
Confirm “TIMER PROGRAMMING” is pointed by
- 32 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 33
5
– TIMER PROGRAMMING –
Set beginning hour
Press the Arrow K or L button until
the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the Arrow B button.
6
Set beginning minute
Press the Arrow K or L button until
the desired minute appears.
(Example: “30” for 7:30PM)
Then, press the Arrow B button.
7
Set end hour
Press the Arrow K or L button until
the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the Arrow B button.
8
Set end minute
Press the Arrow K or L button
until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the Arrow B button.
9
Set the tape speed
Press the Arrow K or L button
until the desired tape speed
appears. (Example: SP)
10
CH DATE
TIMER PROGRAM EXTENSION
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/06 FRI 7:12 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
-
-
-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/06 FRI 7:30 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
B 61 7/06 FRI 7:30 M 8:30 M - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
B 61 7/06 FRI 7:30 M 8:50 M - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
TO CORRECT A PROGRAM
• While setting a program; press the Arrow s but– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
B 61 7/06 FRI 7:30 M 8:50 M SP
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
•
Finish setting the program
Press the Arrow B or s button. The program is now
completed.
• To set another program, repeat steps [2] to [10].
• Press the SETUP button on the remote control to
return to original mode.
11
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
2)Repeat step [1] on page 32.
3)Press the RECORD button and select the desired
program using the Arrow K or L button.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the PAUSE button on the remote control. The recording time
returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automatically be set to the SLP mode.
5)Press the Arrow B or s button to exit the setting
menu. Then press the SETUP button on the remote
control to return to original mode.
Set the timer
Press the POWER button to set automatic timer
recording. The TIMER REC indicator lights up.
• You must turn off the TV/DVD/VHS to activate
automatic timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
ton to go back one step and enter the correct numbers using the Arrow K or L button.
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 32.
3)Press the Arrow B button (or press the Arrow s
button to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the Arrow K or L button.
4)Press the POWER button to set automatic timer
recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
• After setting a program;
•
- 33 -
1)Press the POWER button.
2)Repeat steps [1] ~ [2] on page 32 and select a
program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to
return to TV mode.
While recording is in progress;
1)Press POWER button.
2)Press the STOP/EJECT button on the
TV/DVD/VHS.
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 34
TO CHECK THE BEGIN/END TIME
3
1)Press the POWER button so that the REC indicator
goes off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the Arrow B button. The details of programs
appear on the TV screen.
5)Press the SETUP button on the remote control to
return to TV mode.
•
•
•
•
•
•
Make sure the channel you want to record is properly set in advance.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
If you are recording using a Timer mode, you may
not operate the unit manually.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
If the tape runs out before the end time, the
TV/DVD/VHS will switch to the Stop mode immediately, and the tape will be ejected.
2
SLEEP TIMER
The Sleep Timer function turns off the
TV/DVD/VHS without using the POWER button
after a desired period of time.
NOTE:
• This function does not operate during Recording
mode.
2
Select “SLEEP TIMER”
Set sleep time
Press the SLEEP button until your
desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, exit the Sleep
Timer setting.
Select “USER’S SET UP”
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
SLEEP 120 MINUTES
TO CANCEL THE SLEEP TIMER
Set “AUTO RETURN” to [ON]
Press the Arrow K or L button to
point to “AUTO RETURN”.
Press the Arrow B or s button
until [ON] appears.
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
Press the SETUP button on the
remote control.
Press the Arrow K or L button to
point to “USER’S SET UP”.
Then, press the Arrow B button.
Watch the recorded program
TO CANCEL THE AUTO RETURN
MODE
1
AUTO RETURN
1
4
Press the PLAY button.
HINTS FOR AUTOMATIC
TIMER RECORDING
•
Auto Return will begin
When all the timer recordings are completed, the
TV/DVD/VHS will rewind to the beginning of the
recorded program(s).
NOTE:
• If you press the POWER button while tape is
rewinding, the Auto Return will stop.
– USER’S SET UP –
RENTAL
REPEAT PLAY
B AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[ON]
[HIFI]
[STEREO]
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button
until “SLEEP 0 MINUTES” appears.
- 34 -
EN
1C29
TD503_01-36 02.2.26 10:10 AM Page 35
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
When the Closed Caption mode is ON:
• Counter mode: After 5 seconds, only the counter
• The On Screen Display disappear after 5 seconds.
• This is true even if the MUTE button is pressed, or
•
remains. To clear it, press the DISPLAY button.
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, press
the DISPLAY button.
OFF mode
Counter mode
OFF mode
Clock mode
STOP
SP
the PAUSE button is pressed while recording.
STOP
COUNT 0:12:34
Clock/Counter mode
5:40PM
CH2
STOP
5:40 PM
CH2
SP
After 5 seconds
After 5 seconds
SP
COUNT 0:12:34
5:40PM
CH2
COUNT 0:12:34
Counter
remains
Clock & Channel
remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
5A
2
3
4
5
6
7
8
9
10
11
12
13
A
B
TV Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CATV channel
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
TV Display
CATV channel
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
TV Display
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CATV channel W+10
TV Display
46
CATV channel W+25
TV Display
61
CATV channel W+40
TV Display
76
CATV channel W+55
TV Display
91
CATV channel W+65
TV Display
106
CATV channel W+80
TV Display
121
W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
47
48
49
50
51
52
53
54
55
56
57
58
59
60
W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
62
63
64
65
66
67
68
69
70
71
72
73
74
75
W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
77
78
79
W+56 W+57 W+58
92
93
94
80
81
82
83
84
85
86
A-5
A-4
A-3
A-2
A-1
W+59 W+60 W+61 W+62 W+63 W+64
95
96
97
98
99
100
101
87
102
88
103
89
104
90
105
W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
107
108
109
110
111
112
113
114
115
116
117
118
119
120
W+81 W+82 W+83 W+84
122
123
124
125
- 35 -
EN
1C29
TD503_36-55 02.2.26 10:13 AM Page 36
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this DVD
player.
[DVD]
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If
a function you selected do not run as desired, refer to the
manual accompanying the disc.
Disc Type
Logo
Contents
Disc Size
12 cm
DVD
Video
Sound
and
Pictures
8 cm
Audio
CD
Sound
Maximum
Playback Time
Approx. 4 h
(single-sided)
Approx. 8 h
(double-sided)
Approx. 80 min
(single-sided)
Example
Approx. 160 min
(double-sided)
12 cm
74 min
8 cm
(singles)
20 min
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡Some discs include region codes as shown below.
[AUDIO CD]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on DVD players with the same
region code.
The following discs cannot be played back on this
DVD player.
¡DVD with region codes other than 1 or ALL.
¡DVD-ROM
¡DVD-RAM (Never play back, otherwise
malfunction may result.)
¡CD-ROM
¡VSD
¡CDV (Only plays back the audio part.)
¡CD-G (Only plays back the sound.)
¡CD-R/CD-RW
(Only plays back the discs which audio CD and
MP3 is recorded.)
¡CD-I
(Never play back, otherwise malfunction may
result.)
¡SACD
¡Photo CD
(Never play back, otherwise malfunction may
result.)
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
[MP3]
Data on a MP3 is divided into sections called "albums",
and then into subsections called "tracks", each of which is
given an album or track number.
Example
Album 1
Track 1
Track 2
Track 3
Album 2
Track 4
Track 1
Track 2
Any other discs without compatibility indications
– 36 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 37
PLAYING A DISC
¡If a disc is dirty or has scratches, the pictures may
PLAYING A DVD VIDEO
OR AN AUDIO CD
DVD
CD
Getting started
Turn on the power of the TV, amplifier and any other
components which are connected to the DVD player.
(Change the input system to suit the DVD player, and
check that the sound volume is correct.)
1 Press the POWER button.
¡The power will turn on.
appear distorted and the playback operation may
stop. In such cases, clean the disc and unplug the
power cord and then plug it again before resuming
playback.
¡With DVDs that use some titles for playback
program signals, playback may start from the second
title, or it may skip these titles.
¡During the playback of two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a malfunction.
USING THE DVD MENUS
DVD
2 Press the OPEN/CLOSE button.
¡The disc loading tray will open.
3 Place a disc into the tray.
¡Make sure the disc is sitting properly in the correct
Some DVDs contain their own menus, such as a
guidance menu which describes the contents of the
disc or a selection menu for sound, language and other
customized settings.
recess, with the label side up.
1 Press the DISC MENU button.
¡The DVD menu will appear.
2 Select the desired title.
¡Press the arrow buttons (L/K/B/s) to change the
setting, and then press the ENTER button.
4 Press the PLAY button.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
You need to press the PLAY button only when the
tray has been closed by pressing the OPEN/CLOSE
button.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “USING THE TITLE MENU”.
5 Press the STOP button to stop play.
3 Playback will start from the selected title.
USING THE TITLE MENU
DVD
With a DVD containing a title menu, you can select
desired titles from the menu.
1 Press the TITLE button.
¡The title menu will appear.
2 Select the desired title.
¡Press the arrow buttons (L/K/B/s) to change the
setting, and then press the ENTER button.
Notes
¡If you press the OPEN/CLOSE button in the CALLING UP A MENU SCREEN
TV/VCR mode or power-off, the DVD tray will DURING PLAYBACK
open.
For DVDs
¡If you press the DVD side PLAY button in the
TV/VCR mode or power off, you can start the DVD ¡Press the DISC MENU button to call up the DVD
menu.
playback.
¡
Press the TITLE button to call up the title menu.
¡A “prohibited icon” may appear at
the top-right on the TV screen
Note
during operation, warning that a
¡Contents of menus and corresponding menu
prohibited operation has been
operations may vary between discs. Refer to the
encountered by the DVD player
manual accompanying the disc for details.
or the disc.
EN
– 37 –
01A11
TD503_36-55 02.2.26 10:13 AM Page 38
RESUMING PLAYBACK FROM
THE POINT WHERE
PLAYBACK STOPPED
DVD
PAUSING PLAYBACK OR
DISPLAYING A STILL PICTURE
DVD
CD
1
1 Press the STOP button during playback.
Press the PAUSE button during playback.
¡Playback will pause, with sound
F
muted.
¡Playback will stop, and then
appear the resuming message at
the center.
CD
Press 'PLAY' to play from here.
To play the beginning, press 'STOP' first
and then 'PLAY'.
2 Press the PLAY button to resume playback.
2 Press the PLAY button. Playback will start
from the point where the previous playback
session was stopped.
B
B
Notes
¡Resuming playback is not available with some discs.
STEPPING THROUGH FRAMES
¡It is possible to switch from the DVD play mode to
the TV mode. Even if the power is turned off, the
resume function enables to playback on from the
previously interrupted point. But note that the
Marker commands are not saved.
¡The resume function can be reset by pressing the
DVD
1 Press the PAUSE/STILL button while playback is paused.
¡The next picture frame is dis-
STOP button twice or by opening the disc loading
tray.
F
played with sound muted each
time the button is pressed.
FAST FORWARD/REVERSE
DVD
CD
2 Press the PLAY button to resume playback.
1 Press and hold the g or h button for
B
more than 1 second during playback.
¡For DVDs, pressing the FWD g or REV h but-
ton cycles the playback speed in four steps. In case
of DVDs, the sound will mute.
¡For audio CDs, the playback speed is ×16 fixed.
REV E Button
FWD D Button
Ex2
Dx2
Ex8
Dx8
Ex30
Ex30
Ex60
Ex60
2 Press the PLAY button to return to normal
playback speed.
– 38 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 39
SLOW MOTION
STARTING FROM A DESIRED
TIME COUNT
DVD
DVD
1 Press and hold the g button for more than
1 second while playback is paused. (Sound
remains muted.)
1 Press the SEARCH MODE button twice.
¡Slow motion mode will be activated.
¡Pressing and holding the g button for more than
1 second cycles the playback speed in three steps.
Select an appropriate speed while referring to the
speed indication on the screen.
×1/16
2 Press the numeric buttons to set the desired
time count.
TIME 1:23:30
TOTAL 1:23:45
¡Example: 1 hour, 23 minutes and
×1/2
×1/8
CD
30 seconds
1→2→3→3→0
Notes
D Button
2 Press the PLAY button to return to normal
¡In the case of DVD, Time Search in Title is effec-
tive. (But Time Search in Chapter is ineffective.)
playback speed.
Notes
¡Slow playback is not available with audio CDs.
¡The reverse of slow playback is not available.
¡If you press the g button and release immediately during playback is paused or slow, it returns to
normal playback.
¡In the case of CD, Time Search in Track is effective.
(But Time Search in the entire disc is ineffective.)
¡Playback from a desired time count is not available
with some discs or if the unit is in stop mode.
¡If wrong numbers are entered, press the CLEAR
button and re-enter the correct numbers.
PLAYING FROM A DESIRED
TITLE OR CHAPTER
STARTING FROM A DESIRED
TRACK
DVD
CD
1 Press the SEARCH MODE button and then
1 Press the numeric buttons to enter the
press the numeric buttons to select a title or
a chapter.
¡Perform the title search and the
TT : 1/ 2
CH __ / 49
chapter search after setting them on
the same screen at the same time.
Changeover by K/ L buttons.
¡During playback,press the numeric buttons to select a
Chapter. The Chapter will be located and playback will
start.
¡When playback is stopped, press the numeric buttons to
select a Title. The Title will be located and playback
will start.
Notes
¡Playback from a desired title or chapter is not available with some DVDs.
¡Some discs which the chapter number isn’t displayed cannot playback from a desired chapter.
TT : _/ 12
CH : 12/ 49
desired track number.
¡The selected track will be located, and playback will start.
You can also press the SEARCH
MODE button, use the numeric
buttons to enter the track number.
When the track number is entered
in the entry box, playback of the
desired track will start automatically.
TR __/ 15
TRICKS WITH THE SKIP BUTTONS (H, G)
If the SKIP button G is pressed during playback or
while playback is paused, the current track is
skipped and the next track is played. When the SKIP
button H is pressed once, the top of the current
track is located for replaying. When the SKIP button
H is pressed again while Within 2-second
playback, the previous track is located.
TRICKS WITH THE SKIP BUTTONS (H, G)
If the SKIP button G is pressed during playback or
while playback is paused, the current chapter will be
skipped and the next chapter will be played. When the
SKIP button H is pressed once, the top of the current
chapter will be located for replaying. When the SKIP
button H is pressed again within 2-seconds after
playback begins, the previous chapter will be located.
– 39 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 40
REPEAT
A-B REPEAT
DVD
CD
DVD
1 Press the REPEAT button.
CD
You can define a section to be played back repeatedly.
For DVDs
1 Press the A-B REPEAT button during playback.
¡A single title or chapter is played back repeatedly.
¡Pressing the REPEAT button cycles the display on
¡The starting point (A) will then be
selected.
REPEAT
[A- ]
the screen as follows.
REPEAT
[OFF]
No repeat playback.
REPEAT
[CHAPTER]
The current Chapter is
played back repeatedly.
REPEAT
[TITLE]
The current Title is
played back repeatedly.
2 Press the A-B REPEAT button again at the
end point (B) of the desired section.
¡The selected section will be
played back repeatedly.
REPEAT
[A-B]
For audio CDs
¡The whole disc or a single track is played back
repeatedly.
3 To exit A-B repeat playback, press the A-B
REPEAT button and set it to OFF.
¡Pressing the REPEAT button cycles the display on
the screen through Off, Track and All.
REPEAT
[OFF]
No repeat playback.
REPEAT
[TRACK]
The current Track is
played back repeatedly.
REPEAT
[ALL]
The whole Disc is
played back repeatedly.
REPEAT
[ OFF ]
Notes
¡With DVDs, the A-B repeat section can be set only
within the current title.
¡With audio CDs, the A-B repeat section can be set
within the current track.
¡A-B repeat is not available with some scenes in
If the REPEAT button is pressed once during program/random playback, the program/random playback is performed
repeatedly.
If the REPEAT button is pressed again, the
current track is played back repeatedly.
DVD.
¡To cancel the A point which was set, press RETURN
button.
¡A-B repeat playback is not function during title,
chapter, track or all repeat playback had set.
Notes
¡Repeat playback is not available with some discs.
¡The REPEAT setting will be cleared when moving
to other title, chapter or track.
¡Repeat playback is not function during A-B repeat
playback.
– 40 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 41
MARKER
PROGRAM (Audio CD)
DVD
CD
CD
1 Press the MODE button in stop mode.
You can define the part to be called back.
¡The program screen will appear.
1 Press the SEARCH MODE button three
PROGRAM
TIME
0:00:00
2/2
--
times during playback.
Set the marker
¡Using the cursor (s/ B) button, position the cursor
on to the marker number shown as “NOT SET”.
Press the ENTER button when the screen to be
reviewed appears. The marked
time will be displayed. Up to 5
points can be marked.
1 2 3 4 5 AC
NOT SET
Call back the marker
¡Using the cursor (s/ B) button, position the cursor
on to the marker number to be called back and press
the ENTER button.
Clear the marker
¡Using the cursor (s/ B) button, position the cursor
on to the marker number to be cleared and press the
CLEAR button.
To clear all markers, place the cursor on “AC” (All
clear markers) and press the ENTER button.
2 Press the SEARCH MODE button or the
RETURN button to exit the display.
START: PLAY
RANDOM: MODE
DELETE: CLEAR
EXIT: RETURN
2 Press the numeric buttons to enter the
desired track numbers.
PROGRAM
¡50 programs can be displayed at
once on the screen. Press “L” to
go to the next page.
TIME 2:07:43
1/1
02 05 07 04 10 14 06 15 21 08
20 28 10 25 35 12 30 42 11 34
49 16 40 58 18 45 63 01 03 _
START: PLAY
RANDOM: MODE
DELETE: CLEAR
EXIT: RETURN
3 Press the PLAY button.
¡Playback will start in the programmed order.
¡While the program is being played back, the STOP
button works as follows.
¡Press the STOP button once and then the PLAY
button again, playback will restart from the point
where the STOP button was pressed. (Program
continued)
¡Press the STOP button twice and then the PLAY button again, playback will restart from the track in the
usual way. (Program cleared)
Notes
¡Adding programs is not possible during program
playback. You must stop the current playback before
such operations can be carried out.
¡Press the CLEAR button to cancel a program. The
most recently entered program will then be deleted.
¡Up to 99 programs can be entered.
¡Playback from a desired track and random playback
are not available during program playback.
¡Program settings are cleared when the power is
turned off or the disc loading tray is opened.
¡Press the MODE button to check the programmed
setting.
– 41 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 42
RANDOM (Audio CD)
CD
1 Press the MODE button in stop mode.
¡The program setting menu screen will appear.
2 Press the MODE button again.
RANDOM
Note
START : PLAY
¡Zooming function does not work while disc menu is
EXIT : MODE
shown.
PLAYING AN MP3 DISC
3 Press the PLAY button. Random playback
will then start.
MP3
Note
¡Program playback is not available during random
playback.
1 Insert an MP3 file-recorded disc.
¡The MP3 menu screen shows up.
¡Folders are referred to as
VOLUME LABEL
“ALBUMS” and files are
referred to as “TRACKS”.
ZOOM PLAYBACK
(enlargement onscreen)
¡“+” appears at the beginning
DVD
of the album name.
FIRST PLAY
+ALBUM01
+ALBUM02
+ALBUM03
+ALBUM04
SELECT:
RETURN:
/
1/15
ENTER:
START: PLAY
¡If all the TRACKS cannot be displayed at once on
Images can be enlarged four times on the screen to
your taste.
the screen, “L” appears to go to the next page. If
there is a previous page, “K” appears on-screen. On
the left of “L”, the current page and the total number of pages are displayed.
1 Press the ZOOM button during playback.
¡An image will be enlarged at the center of the
¡The player can recognize 255 ALBUMS and
screen.
TRACKS altogether.
¡Press the ZOOM button again, and the image will be
2 Using the K/L buttons, select a ALBUM or
back to the previous size.
Zoom [x2]
TRACKS to be played.
Zoom [x4]
Zoom [OFF]
2 When the cursor (K/ L/ s / B) button is
pressed during zoom play, the part to be
zoomed moves.
¡The zooming frame can be moved from the center
.... 4 steps to the right. 4 steps to the left. 4 steps to
the top. 4 steps to the bottom when 2 time zooming.
The frames will move 6 steps when 4 time zooming.
[When TRACKS are selected]
The TRACKS will be played
in the order of selection.
[When an ALBUM is selected]
+ALBUM11
+ALBUM12
+ALBUM13
+ALBUM14
+ALBUM15
SELECT:
RETURN:
/
ENTER:
START: PLAY
Press the B button. The TRACK
selection screen shows up. Using
the K/L buttons, select TRACKS
to be played.
¡Choose “FIRST PLAY”, and the ALBUMS and
TRACKS will be played from the beginning of the
disc.
¡Current position will be displayed on the right-bot-
tom of the screen. Press the ENTER button, and the
display disappears.
ALBUM01
¡Press the TITLE button, and the top hierarchy will
be called back.
¡ALBUMS can be played up to the 8th hierarchy.
– 42 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 43
Notes
¡During play, a desired track can be directly searched.
Just type in the TRACK number with the numerical
buttons.
¡If the typed TRACK number is not available, the
“disable” symbol appears and the direct search mode
is cancelled.
¡Playback cannot be started from a desired time
count.
3 Press the PLAY button.
¡Playback will start.
4 To stop the play, press the STOP button.
CHANGING THE ONSCREEN
DISPLAY DURING MP3 DISC PLAY
MP3
PLAYING AN MP3 DISC IN A
PROGRAMMED WAY
The information on an MP3 disc in play can be
checked.
MP3
1 Press the DISPLAY button during playback.
¡The TRACK currently in play
will be highlighted.
1 Press the MODE button in STOP mode.
FOLDER NAME
TRACK11
TRACK12
TRACK13
TRACK14
TRACK15
¡The program screen shows up.
PROGRAM FOLDER NAME
+ALBUM01
+ALBUM02
+ALBUM03
TRACK01
TRACK02
1/11
2 Press the DISPLAY button again.
START: PLAY
RANDOM: MODE
1/1
DELETE: CLEAR
EXIT: RETURN
¡The ALBUM name being displayed will be replaced
by the elapsed time of the track.
2 Using the K/L buttons, select a track. Then
¡
press the ENTER button to save it in a program.
will be displayed when the repeat play has been
selected.
A : Album (folder) repeat
T : Track repeat
D : Disc repeat
0:02:31
PROGRAM - ALBUM01
+ALBUM11
+ALBUM12
TRACK11
TRACK12
TRACK13
1/11
A
TRACK11
TRACK12
TRACK13
TRACK14
TRACK15
START: PLAY
RANDOM: MODE
TRACK11
1/1
DELETE: CLEAR
EXIT: RETURN
¡The programmed track is displayed in the right-hand
screen.
3 Press the DISPLAY button again, and the dis-
¡When the s button is pressed, the album stop in the
current left-hand screen will be highlighted.
play screen disappears.
PLAYING AN MP3 DISC FROM A
DESIRED TRACK
¡If the entire program cannot be displayed at once on
the screen, “L” appears to go to the next page.
3 When the disc has been programmed, press
MP3
the PLAY button.
1 Press the SEARCH MODE button during play-
¡Programmed play starts.
back.
¡The SERACH menu shows up.
¡A track currently in play or under
RESUME ON will be highlighted. In the case of RESUME OFF,
the first track of the disc will be
highlighted.
¡Press the RETURN button, and
the SEARCH menu disappears.
PROGRAM - ALBUM05
+ALBUM51
+ALBUM52
TRACK51
TRACK52
TRACK63
1/11
ALBUM NAME
+ALBUM01
TRACK11
TRACK12
TRACK13
TRACK14
SELECT:
RETURN:
/
START: PLAY
RANDOM: MODE
1/15
ENTER:
START: PLAY
2 Using the K/L buttons, select a track to be
played. Then press the PLAY button to start
playing.
TRACK11
TRACK52
TRACK31
TRACK22
TRACK03
2/3
DELETE:
EXIT:
CLEAR
RETURN
Notes
¡Press the CLEAR button, and the last-programmed
entry will be deleted.
¡Press the RETURN button, and the STOP screen
will show up with the program contents in memory.
¡The program setting will be cancelled when the
power is turned off or the disc tray is opened.
– 43 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 44
PLAYING AN MP3 DISC AT
RANDOM
MP3
1 Press the MODE button twice in STOP mode.
¡The random setting menu screen will appear.
RANDOM
START:
PLAY
EXIT:
MODE
2 Press the PLAY button.
¡Random play starts.
SETTINGS
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE
DVD
AUDIO STEREO
Both right and left channels
are active (stereo).
CD
AUDIO L-CH
Only the left channel is active.
The DVD player has a function which allows you to
select the desired audio language and sound mode.
AUDIO R-CH
Only the right channel is active.
For DVDs
Press the AUDIO button during playback, and then
press the AUDIO button to select the desired audio
language.
¡The audio language can be changed if multiple
languages are recorded on the DVD being played.
Notes
¡Pressing the Audio button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc
menu). Operation varies between discs, so refer to
the manual accompanying the disc.
AUDIO 1.ENG DolbyD 5.1CH 48k/3
AUDIO 2.FRE DolbyD 5.1CH 48k/3
¡Current audio language and sound mode will be dis-
played when you press the AUDIO button at first.
¡If a desired language is not shown after pressing the
AUDIO 3.JPN DolbyD 5.1CH 48k/3
Audio button several times, the disc does not have
an audio source in that language.
¡The audio language resets to the one which has been
HELLO
selected in the setup mode, every time the power is
turned on or discs are replaced. If that language is
not available on a disc, a language defined by the
disc is selected.
Bonjour
For audio CDs
¡The screen display will disappear after about 5
Press the AUDIO button during playback.
¡Pressing the AUDIO button cycles the sound mode
seconds.
¡If you use DIGITAL AUDIO OUT jack, the sound
through STEREO, L-CH and R-CH.
mode of audio CDs can not be changed.
– 44 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 45
CHANGING THE SUBTITLE
LANGUAGE
DVD
¡It may take time to display the subtitles in the
selected language.
¡The screen display will disappear after about 5
seconds.
¡When “SUBTITLE NOT AVAILABLE” appears
onscreen, it means no subtitle is recorded on the
scene.
The DVD player has a function which allows you to
select the desired language for subtitles.
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures)
1 Press the SUBTITLE button during playback,
and then press the SUBTITLE button to
select the desired subtitle language.
DVD
¡The subtitle language can be changed if the subtitles
are recorded in multiple languages on the DVD
being played.
¡The subtitle language cannot be changed if the
subtitles are recorded in a single language on the
DVD being played.
The DVD player has a function which allows you to
select the desired camera angle.
1 Press the ANGLE button during playback.
¡If the disc contains sequences recorded from differ-
Subtitle 1
ent camera angles, the angle icon (
) will appear
at the top-right of the screen. You can change the
camera angle when the icon appears on the screen.
Subtitle 2
¡The camera angle cannot be changed if the disc does
SUBTITLE 1.ENG/6
SUBTITLE 2.FRE/6
not contain sequences recorded from different
camera angles.
SUBTITLE OFF
OFF
2 Press the ANGLE button while the angle
number is shown on the screen.
ANGLE 1 / 8
¡Pressing the SUBTITLE button cycles the subtitle
Angle 1
language from SUBTITLE 1, SUBTITLE 2 and all
the languages recorded.
¡Current subtitle mode will be displayed when you
press the SUBTITLE button at first.
¡Press the SUBTITLE button, and then press the cursor (s/ B) button to set it to on or off.
ANGLE 2 / 8
Angle 2
ANGLE 8 / 8
Angle 8
HELLO
Bon jour
Note
¡The screen display will disappear after about 5
seconds.
¡Current camera angle will be displayed when you
press the ANGLE button at first.
Notes
¡Some discs allow subtitle language setting on the
disc menu. (Operation varies between discs, so refer
to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
¡The subtitle language resets to the one which has
been selected in the setup mode, every time the
power is turned on or discs are replaced. If that
language is not available on a disc, a language
defined by the disc is selected.
– 45 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 46
CHANGING THE ON-SCREEN
DISPLAY
DVD
2 Press the DISPLAY button again.
CD
All
4/12 0:13:45 - 0:45:40
All:
Current track number
/ the number of total
tracks.
You can check the information about the disc by
pressing the DISPLAY button on the remote control.
TIME:
Elapsed time of the
current disk and
remaining time of
the current disc.
For DVDs
¡Use the number button to start from a desired track.
1 Press the DISPLAY button during playback.
CH 7/49 0:01:46 - 0:03:27
TIME:
Elapsed time of the
current chapter and
remaining time of the
current chapter.
CH(Chapter):
Current chapter number
/ the number of total
chapter.
3 Press the DISPLAY button or the RETURN button to exit the display.
BLACK LEVEL SETTINGS
DVD
2 Press the DISPLAY button again.
TT
1/2
You can set to make the black parts of the picture
brighter.
0:00:00 - 1:23:45
TT(Title):
Current title number
/ the number of total
titles.
TIME:
Elapsed time of the
current title on remaining
time of the current title.
1 Press the MODE button during playback.
¡The setup screen will appear.
BLACK LEVEL : OFF
¡Use the number button to start from a desired chap-
ter.
2 Press the ENTER button to set it on or off.
¡ON : It makes the dark parts brighter.(Default : OFF)
OFF : Original picture which is recorded on the disc
will be shown.
¡Press the RETURN button to exit the display.
3 Press the DISPLAY button again.
BIT RATE
C L0
BIT RATE indicator will appear.
BIT RATE shows the quantity of
information which is recorded in DVD.
Layer number(*)
L0: Layer 0 is playing back
L1: Layer 1 is playing back
Current Repeat setting
C: Chapter repeat
T: Title repeat
A B: A-B repeat
TruSurround SETTINGS
You can enjoy stereophonic sound system when you
playback Dolby Digital and PCM 48kHz sound.
*) It appears when the layered disc is playing back.
1 Press the MODE button twice during playback.
4 Press the DISPLAY button or the RETURN but-
¡The setup screen will appear.
ton to exit the display.
2 Press the ENTER button to set it on or off.
For audio CDs
1 Press the DISPLAY button during playback.
TR
TR(Track):
Current track number
/ the number of total
tracks.
SRS TruSurround ON
4/12 0:03:21 - 0:02:15
TIME:
Elapsed time of the
current track and
remaining time of
the current track.
ON : TruSurround ON.(Default : OFF)
OFF : TruSurround OFF.
¡Press the DISPLAY button or the RETURN button
to exit the display.
– 46 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 47
CHANGING THE SETUP ITEMS
LANGUAGE SETTINGS
4 Press the K/L buttons to select a desired
item, and then press the ENTER button.
1 Press the SETUP button in STOP mode.
¡If “OTHER” is selected on the AUDIO, SUBTITLE
¡The setup screen appears.
or DISC MENU setting screen, the Language Code
setting screen will appear. Press the numeric buttons
to enter the desired language code while referring to
the list on page 51.
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT: /
EXIT: SETUP
SET:
ENTER
CANCEL: RETURN
SET-UP
LANGUAGE CONTROLS
DISC MENU
LANGUAGE CODE
2 Press the K/L buttons to select Language,
Please enter a 4-digit Language code.
----
and then press the ENTER button.
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
5 Press the SETUP button.
¡The setup mode will be canceled and the ordinary
screen will appear.
3 Press the K/L buttons to select an item,
and then press the ENTER button.
AUDIO:
(Voice is played back in selected language.)
Note
¡Be sure to press the SETUP button, or the setting
will not work.
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the Audio and
Subtitle button. Details are on pages 44 and 45.
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
ORIGINAL
OFF
ORIGINAL
¡You can also select the item by pressing the numbers
which displayed with the item.
¡When you change the setup items, press the STOP
button if you are in playback mode.
SUBTITLE:
(Subtitles are shown in selected language.)
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
ORIGINAL
OFF
ORIGINAL
DISCMENU:
(The disc menu appears in selected language.)
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
ORIGINAL
OFF
ORIGINAL
– 47 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 48
AUTO POWER OFF (Default : ON)
Set or not set to turn off after the screen saver is started and
no keys are pressed for 30 minutes.
DISPLAY SETTINGS
1 Press the SETUP button in STOP mode.
SET-UP
DISPLAY CONTROLS
¡The setup screen will appear.
SET-UP
1.TV MODE
2.ANGLE ICON
3.AUTO POWER OFF
4.BACKGROUND
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT: /
EXIT: SETUP
4:3 LETTER BOX
ON
ON
BLACK
SET:
ENTER
CANCEL: RETURN
BACKGROUND COLOR (Default : BLACK)
2 Press the K/ L buttons to select DISPLAY Select blue or black.
and then press the ENTER button.
SET-UP
DISPLAY CONTROLS
SET-UP
1.TV MODE
2.ANGLE ICON
3.AUTO POWER OFF
4.BACKGROUND
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
3 Press the K/ L buttons to select an item, and
4:3 LETTERBOX
ON
ON
BLACK
4 Press the K/ L buttons to select a desired
then press the ENTER button.
item, and then press the ENTER button.
TV MODE (Default : 4:3 LETTER BOX)
4:3 LETTER BOX : Wide screen with black bars on top
and bottom
4:3 PAN & SCAN : Full height picture, trimmed both sides
5 Press the SETUP button.
¡The setup mode will be canceled and the ordinary
screen will appear.
SET-UP
DISPLAY CONTROLS
1.TV MODE
2.ANGLE ICON
3.AUTO POWER OFF
4.BACKGROUND
4:3 LETTER BOX
ON
ON
BLACK
SET-UP
DISPLAY CONTROLS
Notes
¡Be sure to press the SETUP button, or the setting
will not work.
¡You can also choose the item by pressing the numbers.
TV MODE
1.4:3 LETTER BOX
2.4:3 PAN & SCAN
ANGLE ICON (Default : ON)
Display or not display the Angle icon on the screen.
SET-UP
DISPLAY CONTROLS
1.TV MODE
2.ANGLE ICON
3.AUTO POWER OFF
4.BACKGROUND
4:3 LETTER BOX
ON
ON
BLACK
– 48 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 49
AUDIO SETTINGS
DTS (Default : OFF)
On : Output DTS sound
Set to On when the unit is connected to DTS
Decoder.
1 Press the SETUP button in STOP mode.
¡The setup screen will appear.
SET-UP
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT: /
EXIT: SETUP
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
SET:
ENTER
CANCEL: RETURN
SELECT:
EXIT:
2 Press the K/ L buttons to select Audio and
/
SETUP
OFF
ON
OFF
AUTO
SET:
ENTER
CANCEL: RETURN
then press the ENTER button.
Down Sampling (Default : AUTO)
Set the output for the DVD
recorded in PCM 96kHz (96kHz or 48kHz)
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT:
EXIT:
/
SETUP
¡Press the K/L buttons to select an item, and then
press the ENTER button.
SET:
ENTER
CANCEL: RETURN
SETUP MENU
3 Press the K/ L buttons to select an item, and
AUDIO OPTIONS
then press the ENTER button.
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
DRC (Default : OFF)
On : DRC
(Dynamic Range Control)
¡This function is for controlling the range of sound
volume. By compressing the range of sound volume,
it is possible not only to suppress the output of loud
sound at night and but also to raise the volume of
low sound.
¡This function is effective only for the sound record-
SELECT:
EXIT:
/
SETUP
OFF
ON
OFF
AUTO
SET:
ENTER
CANCEL: RETURN
SET-UP
AUDIO CONTROLS
DOWN SAMPLING
1.AUTO
2.48kHz
3.96kHz
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
When playing a disc with copyright protection
¡If you select 96KHz, copyright protection will be
ed by Dolby Digital recording.
activated and no sound will come out. If you select
AUTO, sound will be down sampled at 48KHz.
SET-UP
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
SELECT:
EXIT:
/
SETUP
OFF
ON
OFF
AUTO
4 Press the SETUP button.
¡The setup mode will be canceled and the ordinary
SET:
ENTER
CANCEL: RETURN
screen will appear.
Dolby Digital (default : ON)
On : Output by Dolby Digital
Set to On when the unit is connected to Dolby Digital
Decoder.
SET-UP
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
SELECT:
EXIT:
/
SETUP
OFF
ON
OFF
AUTO
SET:
ENTER
CANCEL: RETURN
– 49 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 50
When “PARENTAL LEVEL” is selected
¡Press the K/ L buttons to select an item from “ALL”
PARENTAL LOCK
or 8 to 1 and then press the ENTER button.
1 Press the SETUP button.
¡The setup screen will appear.
SET-UP
PARENTAL CONTROLS
PARENTAL LEVEL
SET-UP
ALL
8
7 [NC-17]
6 [R]
5
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT:
EXIT:
SELECT: /
EXIT: SETUP
SET:
ENTER
CANCEL: RETURN
/
SETUP
SET:
ENTER
CANCEL: RETURN
When “CHANGE” is selected
¡Press the numeric buttons to enter the 4 digits pass-
2 Press the K/L buttons to select PARENTAL,
word. Then press the ENTER button.
and then press the ENTER button.
SET-UP
PARENTAL CONTROLS
SET-UP
PASSWORD
Please enter current password.
----
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
EXIT: SETUP
3 Press the numeric buttons to enter the 4digit password, and then press the ENTER
button.
5 Press the SETUP button.
¡The setup mode will be canceled and the ordinary
screen will appear.
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password from the second time onward.
¡By entering the password, you can then change the
control level and password settings.
CANCEL: RETURN
CONTROL LEVELS
¡ALL
All parental lock is cancelled.
¡Level 8
SET-UP
DVD software of any grade (adult/general/children)
can be played back.
PARENTAL CONTROLS
PASSWORD
¡Levels 7 to 2
Please enter a 4-digit password.
----
Only DVD software intended for general use and
children can be played back.
4 Press the K/L buttons to select an item, and
¡Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
then press the ENTER button.
SET-UP
PARENTAL CONTROLS
1.PARENTAL LEVEL
2.CHANGE
ALL
Notes
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
1) Press the 4, 7, 3, 7 at step 3.
¡Password will be cleared and parental level will be
set to ALL.
2) Proceed the above steps 3-5 again.
– 50 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 51
LANGUAGE CODE LIST
No.
Language
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish [DAN]
German [GER]
Bhutani
Greek [GRE]
English [ENG]
Esperanto
Spanish [SPA]
Estonian
Basque
Persian
Finnish [FIN]
Fiji
Faroese
French [FRE]
Frisian
Irish [IRI]
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian [HUN]
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic [ICE]
Italian [ITA]
Hebrew
Japanese
Yiddish
Japanese [JPN]
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean [KOR]
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Country code
No.
4747
4748
4752
4759
4764
4765
4771
4772
4847
4851
4853
4854
4855
4860
4861
4864
4947
4961
4965
4971
5047
5051
5072
5158
5160
5161
5165
5166
5167
5247
5255
5256
5261
5264
5271
5347
5350
5358
5360
5367
5447
5455
5464
5467
5471
5547
5551
5557
5560
5565
5566
5569
5647
5655
5669
5747
5757
5758
5759
5760
5761
5765
5767
5771
5847
5860
5861
5866
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
Language
Latvian;Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch [DUT]
Norwegian [NOR]
Occitan
(Afan)Oromo
Oriya
Panjabi
Polish
Pashto;Pushto
Portuguese [POR]
Quechua
Rhaeto-Romance
Kirundi
Romanian [RUM]
Russian [RUS]
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswat
Sesotho
Sundanese
Swedish [SWE]
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish [TUR]
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Chinese [CHI]
Zulu
Country code
5868
5953
5955
5957
5958
5960
5961
5964
5965
5966
5971
6047
6051
6058
6061
6149
6159
6164
6247
6258
6265
6266
6367
6459
6460
6461
6467
6469
6547
6550
6553
6554
6555
6557
6558
6559
6560
6561
6563
6564
6565
6566
6567
6568
6569
6647
6651
6653
6654
6655
6657
6658
6660
6661
6664
6665
6666
6669
6757
6764
6772
6855
6861
6961
7054
7161
7254
7267
If you choose a Language that has a 3 letter language code, the code will be displayed everytime you change the
Audio or Subtitle language setting on pages 21 and 22. If you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
EN
– 51 –
01A11
TD503_36-55 02.2.26 10:13 AM Page 52
TROUBLESHOOTING GUIDE
TV/VCR
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
No power.
Remote Control Doesn’t Work
No picture and sound.
No picture or poor picture on
TV/DVD/VHS.
No sound or poor sound.
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Picture OK, Sound Poor
Timer recording is not possible.
Cannot go into Record mode.
CORRECTIVE ACTION
• Make sure the AC cord is connected to an AC outlet.
• Make sure the power is turned on.
• Is TV/DVD/VHS plugged in?
• Power at outlet?
• Check batteries in Remote Control.
• Make sure the AC cord is connected to an AC outlet.
• Check antenna connection.
• Let the TV/DVD/VHS program its tuner memory.
• Adjust direction or replace antenna.
• Adjust picture controls.
• Adjust volume control on remote control or main unit.
• Press the MUTE button to restore sound.
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Try a new channel, if OK, then possible station trouble.
• If outside antenna is being used, check for broken wire.
• Try a new channel, if OK, then possible station trouble.
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust COLOR control.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust CONTRAST & BRIGHT control.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Adjust CONTRAST & BRIGHT control.
• Try a new channel, if OK, then possible station trouble.
• Check for local interference.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the TV/DVD/VHS clock is set correctly.
• Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
– 52 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 53
PROBLEM
Playback picture is partially noisy.
No picture but the audio is OK in
playback.
No operation by infrared Remote
Control.
Video or color fades in and out
when making a copy of a video tape.
Uneven color
CORRECTIVE ACTION
• Adjust tracking control for a better picture using the CHANNEL K
• or L button on the TV/DVD/VHS.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 53.
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
• Unplug the AC cord for about 30 minutes, then plug it again.
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
My TV/DVD/VHS is showing
• You are watching a live broadcast and spelling errors made by the
captions that are misspelled.
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/DVD/VHS will not show
• Captions that are delayed a few seconds behind the actual
the text dialogue
are common for live broadcast. Most captioning production
in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words
what is being said.
• per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with
• Interference caused by building, power lines, thunderstorms, etc.
white boxes on the TV screen.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box
• company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
• You are in the TEXT mode. Select CAPTION mode to CAPTION
on certain channels.
• [OFF].
– 53 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 54
DVD
If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the
player, consulting the following checklist.
Symptom
No power.
The player does not
respond to the
remote control.
No picture
Disc cannot be
played
No sound
Distorted picture
Audio or subtitle
language does not
match the setup.
The camera angle
cannot be changed.
Audio or subtitle
language cannot be
changed.
"Prohibited icon"
appears on the screen,
prohibiting an operation.
CD sound dropout
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
Cause
Remedy
• Loose power plug.
• The remote control is not aimed
• at the sensor on the TV/DVD.
• Obstacles present between the
• remote control and the sensor.
• The remote control is too far
• away from the TV/DVD.
• Dead batteries.
• Loose video connection.
• Wrong disc.
• No disc.
• Dirty disc.
• Disc is placed upside down.
• Parental lock is active.
• Loose audio connection.
• The power of the connected
• audio component is off.
• Wrong audio output settings.
• Wrong input settings on the
• connected audio component.
• Copy protection is active.
• Immediately after playing,
• press fast forward or in reverse.
• The 1st layer is switching to the
• 2nd layer, when playing a two
• layered disc.
• The selected language is not
• available for audio or subtitles
• on the DVD.
• The DVD does not contain
• sequences recorded from
• different camera angles.
• The DVD does not contain
• audio source or subtitles in the
• selected language.
• That operation is prohibited by
• the TV/DVD or disc.
• Scratched disc
• Insert the power plug firmly into the wall out let
• Aim the remote control directly at the sensor
• on the TV/DVD.
• Remove the obstacles from the signal path.
• Use the remote control within 7m of
• the TV/DVD.
• Replace the batteries.
• Connect the video cables firmly.
• Insert a correct video disc that plays on this
• TV/DVD.
• Insert a disc.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio
• component.
• Connect the player directly to the TV.
• There are some cases where pictures may be
• slightly distorted, which are not a sign of a
• malfunction.
• Although Pictures may stop for a moment,
• this is not a malfunction.
• No malfunction.
• No malfunction.
• No malfunction.
• No malfunction.
• Replace the disc with unscratched one.
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
– 54 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 55
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
•
the TV/DVD with a soft cloth immersed in lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/DVD. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-968-3429, to
locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
AUTO HEAD CLEANING
SERVICING
• Automatically cleans video heads as you insert or
•
remove a cassette, so you can see a clear picture.
Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your TV/DVD/VHS may
need to be cleaned.
• Should your TV/DVD become inoperative, do not
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800256-2487, to locate an Authorized Service Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
• If the player still does not perform properly when it is operated while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Use discs which have the following logos on them.
(Optical audio digital discs.)
• Handle the discs so that fingerprints and dust do
•
not adhere to the surfaces of the discs.
Always store the disc in its protective case when it
is not used.
• To clean-off, use a soft cloth.
• Do not use a hard cloth since this will mar the disc.
• Wipe the disc in a straight line from center to edge.
• Never wipe with a circular motion.
• Do not use detergent or abrasive cleaning agents.
– 55 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 56
SPECIFICATIONS
GENERAL SPECIFICATIONS
Sound output:
TV/VCR
CRT :
19 inch in-line gun, 90˚
deflection tube
Television system :
NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Rotary four-head
Tape width :
1/2 inch
Tape speed
SP :
33.40mm/sec.
LP :
16.67mm/sec.
SLP :
11.12mm/sec.
Tuner channel
TV VHF Low :
#2~#6
TV VHF High :
#7~#13
TV UHF :
#14~#69
CATV
VHF :
5A
MID band :
A5~A1, A~I
SUPER band :
J~W
HYPER band :
W+1~W+84
DVD
Product type:
Discs:
Output signal format:
Frequency response
(out put jack)
DVD (linear sound):
ELECTRICAL SPECIFICATIONS
DVD Player
DVD video, Audio CD
NTSC color
2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input:
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output:
Analog audio L/R
output :
Remote control:
Operating
temperature:
Power requirements:
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
Accessories:
20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz
(sample rate: 96 kHz)
20 Hz to 20 kHz
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
1/8” stereo (3.5 mm)
One pin jack,
500m Vpp (75 ohm)
RCA connector [ 2
Digital encoded
infrared light system
5ºC to 40ºC
(41ºF~104ºF)
AC 120V, 60Hz
85W
19"
H:19-21/32” (500mm)
W:23-13/16” (605mm)
D:18-11/16” (475mm)
48.5 lbs (22kg)
Remote Control Unit with
2"AA"batteries
Owner’s Manual
CD:
Signal-to-noise ratio
(S/N ratio)(out put jack)
CD:
100 dB (EIAJ)
Dynamic range
(out put jack)
DVD (linear sound): 85 dB
CD:
84 dB (EIAJ)
Total distortion factor
CD:
0.07% (EIAJ)
Wow and flutter:
Below the measurement
limitation (+/-0.001%
W PEAK) (EIAJ)
• Designs and specifications are subject to change without notice and without our legal obligation.
• If there is a discrepancy between languages, the default language will be English.
– 56 –
EN
01A11
TD503_36-55 02.2.26 10:13 AM Page 57
MEMO
– 57 –
EN
01A11
TD503UDES 02.2.26 10:14 AM Page 58
INDICE
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 58
PANEL FRONTAL DEL televisor/DVD/VHS . . . . . . . . . 58
MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 58
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 60
CONEXIONES DE ANTENA/TELEVISIÓN
POR CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
INSTALACIÓN DE LAS PILAS. . . . . . . . . . . . . . . . . . . 60
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 60
MODE DE ENTRADA EXTERNA. . . . . . . . . . . . . . . . . 60
CONEXIÓN A UN SISTEMA ESTÉREO (Para DVD) . . 60
CONEXIÓN A UN AMPLIFICADOR EQUIPADO CON
TOMAS DE ENTRADA DIGITAL PARA, POR EJEMPLO,
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 60
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL,
DECODIFICADOR DTS O DECODIFICADOR MPEG
(Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6. Botón OPEN/CLOSE
Púlselo para insertar discos en la bandeja o
retirarlos de ella.
7. Bandeja de carga del disco
8. Indicador de DVD
Parpadea durante el modo del DVD.
9. Botón SELECT
Púlselo para cambiar a un modo de televisor,
modo de entrada externa o modo de DVD.
10. Indicador del televisor/ la videograbadora
(TV/VCR)
Parpadea durante el modo del televisor/ la
videograbadora
11. Botones CHANNEL K/L
Púlselo para seleccionar el canal memorizado.
Púlselo para cambiar a un modo de televisor
cuando modo de DVD.
12. Indicador de grabación (RECORD)
TV SECTION
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . . . 62
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 62
PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 62
DVD SECTION
■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 63
REPRODUCCIÓN DE UN DVD DE VÍDEO O UN CD DE
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
CONTROLES DE
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL
TELEVISOR/DVD
Consulte la figura 1 de la página 9
MANDO A DISTANCIA
Consulte la figura 2 de la página 9
VISTA POSTERIOR
Consulte la figura 3 de la página 10
1. Botón POWER
Púlselo para conectar y desconectar la alimentación.
2. Botones VOLUME X/Y
Púlselos para controlar el nivel del volumen para
el DVD y el televisor.
3. Botones SKIP (para DVD)
Salta capítulos o pistas hasta un punto deseado.
4. Botón PLAY
Inicia la reproducción del contenido del disco o la
cinta.
5. Botón STOP
Detiene la operación del disco o la cinta.
Parpadea durante la grabación.
Se enciende en el modo de espera de la grabación con
temporizador.
Botón de grabación de un toque (OTR)
Activa la grabación de un toque. (Sólo en el televisor/DVD/VHS)
13. Botón de grabación (REC)
Púlselo para iniciar la grabación manual.
14. Botón de rebobinado (REW) (para televisor/
videograbadora)
Púlselo para rebobinar la cinta, o para ver la imagen en
retroceso rápido durante el modo de reproducción.
(Búsqueda con rebobinado)
15. Botón de avance rápido (FWD) (para televisor/
videograbadora)
Púlselo para avanzar rápidamente la cinta, o para ver la
imagen en avance rápido durante el modo de reproducción. (Búsqueda con avance rápido)
16. Botón de parada (STOP)
Púlselo para detener la cinta.
Botón de expulsión (EJECT)
Púlselo en el modo de parada para expulsar la cinta del
televisor/videograbadora.
17. Ventanilla del sensor del mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y
escuchar en privado.
19. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
21. Compartimiento del videocasete
22. Botón PICTURE
Presione para entrar en el modo de ajuste de imagen.
– 58 –
ES
1D18
TD503UDES 02.2.26 10:14 AM Page 59
23. Botones de números
Modo del televisor:
Pulse dos dígitos para tener acceso directamente
al canal deseado.
Recuerde pulsar "0" antes de elegir un canal de un
solo dígito.
38. Botón RETURN
Para volver a la operación anterior.
39. Botón ENTER
Púlselo para establecer un ajuste.
40. Botones de flechas
Modo de televisor:
Botón +100
Púlselo para seleccionar un modo de ajuste desde
el menú que aparece en la pantalla del televisor.
Púlselo para seleccionar o ajustar desde un menú
particular.
Púlselo para seleccionar canales de televisión por
cable cuyo número sea igual o superior al 100.
Modo DVD:
Púlselo para introducir el número deseado.
Modo de DVD:
Botón +10
Se utiliza cuando se hacen ajustes mientras se
observa la visualización en una pantalla de televisor.
Púlselo para introducir los números deseados
cuyo número sea igual o superior al 10.
24. Botón PAUSE
Hace una pausa en la operación del disco o la
cinta.
25. Botón de velocidad de cinta (SPEED)
Púlselo para elegir la velocidad de grabación deseada:
SP/SLP.
26. Botón C-RESET
Púlselo para reponer el contador a 0:00:00.
27. Botón DISPLAY
Modo del televisor/ la videograbadora:
Púlselo para visualizar el número del canal en la
pantalla. Si lo pulsa de nuevo, el número del canal
desaparecerá.
Modo de DVD:
Visualiza el estado actual en la pantalla del televisor con fines de comprobación.
28. Botón SETUP
Púlselo para activar o salir del modo de menús de
televisor o preparación de DVD.
29. Botón TITLE
Visualiza el menú de títulos.
30. Botón CLEAR
Repone un ajuste.
31. Botón MODE
Activa el modo de reproducción programada o el
modo de reproducción aleatoria.
32. Botón SEARCH MODE
Púlselo para localizar un punto deseado.
33. Botón AUDIO
Púlselo para seleccionar un idioma de audio o un
modo de sonido deseado.
34. Botón SUBTITLE
Púlselo para seleccionar un idioma de subtítulos
deseado.
35. Botón REPEAT
Repite la reproducción del disco, título, capítulo o
pista actual.
36. Botón ANGLE
Púlselo para cambiar el ángulo de la cámara y
verde, desde un ángulo diferente, la secuencia que
está siendo reproducida.
37. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
41. Botón DISC MENU
Visualiza menús de DVD.
42. Botón ZOOM
Amplia parte de una imagen de DVD reproducida.
43. Botón MUTE
Pulse el botón MUTE para apagar el sonido de un
programa de TV. La visualización del nivel del
sonido cambia de ROJO CLARO a AZUL
CLARO.) Pulse de nuevo el botón MUTE o el
botón VOL K o L para restaurar el sonido.
44. Botón SLEEP
Ajusta el temporizador para dormir.
45. Botón SELECT
Pulse para cambiar entre los modos TV/VCR y
DVD. Podrá ver el modo (TV/VCR o DVD) en el
indicador del panel delantero.
46. Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por
cable o sistema de satélite.
47. Cable de alimentación
Conéctelo a una toma de CA convencional (120
V/60 Hz).
NOTA: Retire el cable de alimentación del gancho
para evitar romperlo antes de conectarlo a
una toma de CA convencional.
48. Toma de salida de audio digital COAXIAL
Conéctela a la entrada digital de un amplificador o
decodificador externo.
49. Toma de salida AUDIO L/R
Conéctela a la entrada de audio analógico de un
amplificador o decodificador externo.
NOTA: Las tomas de entrada de audio (roha y
blanca) en el lado trasero sirven para producir no el son televisor ni el son de
entrada externa, sino el son DVD.
– 59 –
ES
1D18
TD503UDES 02.2.26 10:14 AM Page 60
PREPARACIÓN PARA LA
UTILIZACIÓN
fuente a las tomas AUDIO L/R y VIDEO de este televisor/DVD/VHS. Y luego pulse el botón SELECT
hasta que "VIDEO" aparezca en la pantalla.
CONEXIONES DE ANTENA/
TELEVISIÓN POR CABLE
NOTA:
• Cuando conecte una videograbadora monoaural
(otra fuente) a este televisor/DVD/VHS, conecte la
toma de salida de audio de la videograbadora
monoaural (otra fuente) a la toma AUDIO L de este
televisor/DVD/VHS. El audio saldrá igualmente en
los canales L y R.
Consulte la figura 4 de la página 11
ANTENAS SEPARADAS DE VHF/UHF
En algunas áreas será necesario utilizar una antena
exterior.
Consulte la figura 5 de la página 12
Conexiones de antena/televisión por cable
Continúa en la página siguiente.
Consulte la figura 4 de la página 11
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su
televisor/DVD/VHS sin necesidad de caja de convertidor.
Consulte la figura 4 de la página 11
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su proveedor de servicios de televisión por cable le
suministra una caja de convertidor o si usted utiliza
un sistema de satélite, podrá utilizar la conexión básica mostrada aquí.
Consulte la figura 4 de la página 11
INSTALACIÓN DE LAS PILAS
1) Abra la tapa del compartimiento de las pilas del
mando a distancia presionándola en el sentido de
la flecha.
2) Inserte 2 pilas tamaño "AA" en su compartimiento
colocando las polaridades (+/-) en sus posiciones
correspondientes.
3) Vuelva a poner la tapa.
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada de audio/vídeo de la parte delantera del televisor/DVD/VHS.
Conecte las tomas de salida de audio/vídeo de otra
MODO DE ENTRADA EXTERNA
Cuando utilice una señal de entrada externa (otra
videograbadora o una videocámara), conecte los
cables de salida de audio/vídeo del equipo de reproducción a las tomas AUDIO IN/VIDEO IN de su
televisor/videograbadora. Y luego pulse el botón
CHANNEL K o L hasta que “AUX” aparezca en la
pantalla.
Usted puede programar el temporizador para que
explore todos los canales que puedan recibirse en su
zona.
CONEXIÓN A UN SISTEMA
ESTÉREO (Para DVD)
Consulte la figura 6 de la página 13
NOTAS:
• Asegúrese de desconectar la alimentación a todos
los componentes del sistema antes de hacer la
conexión a otro componente.
• Consulte el manual del propietario de su sistema
estéreo y de cualquier otro componente que vaya a
conectar al televisor/DVD/VHS.
• Las tomas de entrada de audio (roha y blanca) en el
lado trasero sirven para producir no el son televisor
ni el son de entrada externa, sino el son DVD.
CONEXIÓN A UN
AMPLIFICADOR EQUIPADO
CON TOMAS DE ENTRADA
DIGITAL PARA, POR EJEMPLO,
PLATINA MD O PLATINA DAT
(Para DVD)
Utilice un cable digital coaxial (de venta en el comercio) para las conexiones de audio.
– 60 –
Consulte la figura 7 de la página 13
ES
1D18
TD503UDES 02.2.26 10:14 AM Page 61
NOTAS:
• La fuente de audio de un disco del formato de
sonido ambiental Dolby Digital de 5,1 canales no
puede ser grabada como sonido digital por una
platina MD o DAT.
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de hacer la
conexión a otro componente.
• Consulte los manuales del propietario de los componentes que vaya a conectar al
televisor/DVD/VHS.
• Ponga DOLBY DIGITAL y DTS en OFF para la
salida de audio en el modo de preparación. La
reproducción en el televisor/DVD/VHS utilizando
los ajustes incorrectos puede generar distorsión de
ruido, y también puede estropear los altavoces.
• El audio se silenciará cuando DOLBY DIGITAL se
ponga en OFF y VIRTUAL 3D se ponga en ON
para la salida de audio en el modo de preparación y
usted seleccione la fuente de audio del formato de
sonido ambiental Dolby Digital de 5,1 canales.
• A menos que se haga la conexión a un decodifi-
•
cador Dolby Digital o DTS, ponga DOLBY DIGITAL y DTS en OFF para la salida de audio en el
modo de preparación. La reproducción en el televisor/DVD/VHS utilizando los ajustes incorrectos
puede generar distorsión de ruido, y también puede
estropear los altavoces.
El audio se silenciará cuando DOLBY DIGITAL se
ponga en OFF y VIRTUAL 3D se ponga en ON
para la salida de audio en el modo de preparación y
usted seleccione la fuente de audio del formato de
sonido ambiental Dolby Digital de 5,1 canales.
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories. Trabajos confidenciales sin
publicar.
“DTS” y “DTS Digital Out” son marcas de
fábrica de Digital Theater Systems, Inc.
CONEXIÓN A UN
DECODIFICADOR DOLBY
DIGITAL, DECODIFICADOR
DTS O DECODIFICADOR
MPEG (Para DVD)
Si se utiliza este televisor/DVD/VHS para reproducir
fuentes del formato de sonido ambiental Dolby
Digital de 5,1 canales o de sonido ambiental DTS, el
televisor/DVD/VHS dará salida a un flujo de datos
Dolby Digital o DTS desde su toma de salida de
audio digital COAXIAL. Conectando el reproductor a
un decodificador Dolby Digital o DTS, usted podrá
disfrutar de un ambiente más convincente y real con
un sonido ambiental potente y de alta calidad de tipo
profesional tal como el que se oye en salas de cine.
Utilice cables digitales coaxiales (de venta en el comercio) para las conexiones de audio.
Consulte la figura 8 de la página 14
NOTAS:
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de hacer la
conexión a otro componente.
• Consulte los manuales del propietario de los componentes que vaya a conectar al
televisor/DVD/VHS.
• Si conecta un decodificador Dolby Digital, ponga
DOLBY DIGITAL en ON para la salida de audio
en el modo de preparación.
• Si conecta un decodificador DTS, ponga DTS en
ON para la salida de audio en el modo de
preparación.
– 61 –
ES
1D18
TD503UDES 02.2.26 10:14 AM Page 62
TV SECTION
AJUSTE DEL RELOJ
Cerciórese...
• La alimentación del televisor/videograbadora
deberá estar conectada.
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 1 de mayo de 2001
HORA: 5:40 PM
PREPARACIÓN PARA LA
UTILIZACIÓN
PREPARACIÓN DE CANALES
POR PRIMERA VEZ
1
1
Conecte el cable de alimentación a una toma de CA
convencional.
NOTA: Si aparecen algunos dígitos en la esquina de
la pantalla, pulse el botón POWER sin desenchufar el cable de alimentación.
2
Pulse el botón POWER para encender el
televisor/DVD/VHS.
Pulse el botón SETUP en el mando a distancia.
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE RELOJ”. Luego, pulse el botón F.FWD/B.
2
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE MANUAL RELOJ”. Luego, pulse el botón
F.FWD/B.
3
3
Seleccione "ESPAÑOL" o "ENGLISH" (inglés),
"FRANÇAIS" (francés) utilizando el botón de flecha
B o s.
4
Pulse el botón flecha K o L para señalar “AUTOPRESELECCION”.
Luego pulse el botón flecha B. El sintonizador
explorará y memorizará todos los canales activos de
su área.
NOTAS:
• El televisor/videograbadora distingue entre los
canales de televisión estándar y los canales de televisor por cable.
• Si desea reproducir o grabar una cinta ANTES de
preajustar el sintonizador, usted tendrá que pulsar
el botón SETUP en el mando a distancia. Para
preajustar de nuevo el sintonizador, consulte
“REPETICIÓN DE LA PREPARACIÓN DE
CANALES”.
• La unidad de televisor/videograbadora puede
reconocer los canales de TV como ellos de TV por
cable a causa de los condiciones de recepción. En
este caso, pruebe el preajuste automático de nuevo
en los condiciones finas de recepción.
5
El sintonizador se para en el canal memorizado más
bajo. Si desea recuperar canales seleccionados, usted
podrá seleccionar directamente el canal deseado con
los botones numerados del mando a distancia o con
los botones CHANNEL K o L.
Pulse el botón PLAY/K o STOP/L hasta que aparezca el mes deseado. (Ejemplo: Mayo - 05) Luego,
pulse el botón F.FWD/B.
4
Pulse el botón PLAY/K o STOP/L hasta que aparezca el día del mes deseado. (Ejemplo: 1 - 01) Luego,
pulse el botón F.FWD/B.
5
Pulse el botón PLAY/K o STOP/L hasta que aparezca el año deseado. (Ejemplo: 2001) Luego, pulse el
botón F.FWD/B.
6
Pulse el botón PLAY/K o STOP/L hasta que aparezca la hora deseada. (Ejemplo: 5, PM) Luego, pulse el
botón F.FWD/B.
7
Pulse el botón PLAY/K o STOP/L hasta que aparezca el minuto deseado. (Ejemplo: 40)
8
Pulse el botón SRTUP en el mando a distancia.
Aunque los segundos no se visualizan, éstos
empiezan a contar desde 00 cuando se pulsa SETUP
en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta.
– 62 –
ES
1D18
TD503UDES 02.2.26 10:14 AM Page 63
DVD SECTION
REPRODUCCIÓN DE UN
DISCO
REPRODUCCIÓN DE UN DVD
DE VÍDEO O UN CD DE AUDIO
DVD
CD
Para empezar
Conecte la alimentación del televisor, amplificador y
cualquier otro componente que esté conectado al
reproductor DVD. (Cambie el sistema de entrada para
adaptarlo al reproductor DVD, y compruebe que el
volumen del sonido sea correcto.)
1 Pulse el botón POWER.
¡La alimentación se conectará.
2 Pulse el botón OPEN/CLOSE.
¡La bandeja de carga del disco se abrirá.
3 Ponga un disco en la bandeja.
¡Asegúrese de que el disco esté correctamente asen-
tado en el hueco correcto, con el lado de la etiqueta
hacia arriba.
4 Pulse el botón PLAY.
¡La bandeja se cerrará automáticamente y la repro-
ducción empezará desde el primer capítulo o pista
del disco. Necesitará pulsar el botón PLAY sólo
cuando la bandeja haya sido cerrada pulsando el
botón OPEN/CLOSE.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú tal vez aparezca en la pantalla. En este caso, consulte "UTILIZACIÓN DEL
MENÚ DE TÍTULOS".
5 Pulse el botón STOP para detener la reproducción.
– 63 –
ES
1D18
TD503_36-55 02.2.26 10:13 AM Page 64
LIMITED WARRANTY
FUNAI CORP. will repair this Emerson product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest Emerson Authorized Service Center or for general service procedure, please
call 1-800-256-2487 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-256-2487
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
0EMN01954
TD503UD ★★★★★