Emerson EWC19T4 Owner's Manual

T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 1
OWNER’S
MANUAL
“EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.”
COLOR TV/VCR/DVD TRIPLE COMBO
EWC19T4
(19 inch)
SUPPLIED ACCESSORIES
ACCESSORIES
PART NO.
Remote Control Unit NE223UD
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR ®
Partner, our company has
determined that this product meets
the ENERGY STAR ® guidelines for
energy efficiency. ENERGY STAR ®
is a U.S. registered mark.
Batteries
2 AA Batteries
Owner’s Manual
1EMN20183
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-256-2487.
Or visit our WEB SITE at http://www.funai-corp.com
Please read before using this equipment
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
AMEUBLES- Cet appareil ne doit SYMBOLE D'AVERTISSEMENT POUR
être placé que sur un meuble (avec APPAREILLESETCOMPOSANTES
MEUBLE A ROULETTES
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation
d’une force excessive et des surS3126A
faces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug the unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by
the unit manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this unit near water-for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and
the like.
8.Accessories-Do not place this unit on an unstable cart,
stand, tripod, bracket, or table. The unit may fall, causing
serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the unit.
Any mounting of the appliance
PORTABLE CART WARNING
should follow the manufacturer’s
instructions and should use a mounting accessory recommended by the
manufacturer. An appliance and cart
combination should be moved with
care.Quick stops, excessive force,
and uneven surfaces may cause the
S3126A
appliance and cart combination to
overturn.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the unit and to protect it from overheating, and
these openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed,
sofa, rug, or other similar surface. This unit should never be
placed near or over a radiator or heat register. This unit
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
10.Power Sources-This unit should be operated only from the
type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For the
unit intended to operate from battery power, or other
sources, refer to the operating instructions.
11.Grounding or Polarization-This unit is equipped with a
polarized alternating-current line plug(a plug having one
blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
-2-
EN
1B15
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 3
F IGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECT RICAL CODE
ANTE NNA
L EAD I N
WI RE
GROUND
CLAMP
A NTENNA
DI SCHARG E UN I T
(NEC SECTION 8 10 -2 0)
EL ECT RI C
SE RV I CE
EQ U I PM EN T
G RO UNDI NG CO NDUCT ORS
(NEC SECTION 8 10 -2 1)
G RO UND CL AM PS
NEC - NATI O NAL EL ECTRI CAL CO DE
POWER SERVI C E G RO UNDI NG
EL EC TR O DE SYST EM
(NEC ART 2 50 , PART H)
S2 8 9 8 A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the unit, be sure the antenna
or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
19.Damage Requiring Service-Unplug this unit from the wall
outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
unit.
c. If the unit has been exposed to rain or water.
14.Lightning-For added protection for this unit receiver during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the unit due to lightning and power-line
surges.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the
unit.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment
of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the unit to its normal operation.
e. If the unit has been dropped or damaged in any way.
f. When the unit exhibits a distinct change in performancethis indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to
this unit, ask the service technician to perform routine safety checks to determine that the unit is in proper operating
condition.
22.Heat-This unit product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this unit yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
-3-
EN
1B15
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 4
PRECAUTIONS
LASER SAFETY
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to service this device, due to possible eye injury.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
-4-
EN
1B15
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 5
LOCATION
WARNING
For safe operation and satisfactory performance of
your unit, keep the following in mind when selecting
a place for its installation:
• Shield it from direct sunlight and keep it away from
sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top or bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place or
after heating a cold room or under conditions of high
humidity. If a DVD is played in a unit which has
moisture, it may damage the DVD and the unit.
Therefore when the condensation occurs inside the
unit, turn the POWER on and allow at least 2 hours
for the unit to dry out.
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following
meanings
TV/VCR
: Description refers to TV/VCR operation (in the
TV/VCR mode).
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting
•
•
•
CD
: Description refers to playback of Audio CDs
(in the DVD mode).
it from an AC wall outlet. Grasp it by the plug.
If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the disc
loading tray of the unit.
Do not place anything directly on top of the unit.
MP3
: Description refers to playback of MP3 discs
(in the DVD mode).
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/VCR/DVD has the same
serial number as yours. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
-5-
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 6
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . .2, 3
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . .9, 10
C PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPUT JACKS . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS SUCH AS MD
DECK OR DAT DECK (for DVD) .13
CONNECTING TO A DOLBY
DIGITAL DECODER (for DVD) . .14
TV/VCR SECTION
C SET UP FOR USE . . . . . . . . . . . . .15
SELECTING THE LANGUAGE . .15
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . .15, 16
DAYLIGHT-SAVING TIME . . . . . .17
CHANNEL SET UP . . . . . . . . . . . .18
DELETING (OR ADDING)
CHANNEL(S) . . . . . . . . . . . . . . . . .18
C TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C MTS(Multi-Channel Television
sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C VIDEO CASSETTE . . . . . . . . . . . . .25
C PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICAL HOLD CONTROL . . .26
TITLE / CHAPTER SEARCH . . . .39
TIME SEARCH . . . . . . . . . . . . . . .39
MARKER SETUP SCREEN . . . . . .39
C SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C SPECIAL PLAYBACK FUNCTION . . .40
REPEAT . . . . . . . . . . . . . . . . . . . . .40
PROGRAM . . . . . . . . . . . . . . . . . . .40
RANDOM PLAYBACK . . . . . . . . .40
C SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING
RECORDING . . . . . . . . . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C PLAYING A MP3 DISC . . . . . . . . . .41
MP3 PLAYBACK . . . . . . . . . . . . . .41
REPEAT . . . . . . . . . . . . . . . . . . . . .41
PROGRAM . . . . . . . . . . . . . . . . . . .41
RANDOM PLAYBACK . . . . . . . . .41
C CHANGING THE SETTINGS . . . .42
SUBTITLE LANGUAGE . . . . . . . .42
AUDIO LANGUAGE . . . . . . . . . . .42
STEREO SOUND MODE . . . . . . . .42
CAMERA ANGLE . . . . . . . . . . . . .42
BLACK LEVEL SETTING . . . . . . .42
VIRTUAL SURROUND . . . . . . . . .42
C THE ON-SCREEN INFORMATION . . .43
C TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C CHANGING THE DVD SETUP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .44
LANGUAGE SETTING . . . . . . . . .44
DISPLAY SETTING . . . . . . . . . . . .45
AUDIO SETTINGS . . . . . . . . . . . .45
PARENTAL CONTROL . . . . . . . . .46
INITIALIZE . . . . . . . . . . . . . . . . . .46
C ON SCREEN DISPLAY . . . . . . . . .35
C MAINTENANCE . . . . . . . . . . . . . . .50
DISC HANDLING . . . . . . . . . . . . .50
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
C TROUBLESHOOTING GUIDE . . .47
C SPECIFICATIONS . . . . . . . . . . . . .51
DVD SECTION
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .52
C ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
C WARRANTY . . . . . . . . . . .Back Cover
C PLAYING A DISC . . . . . . . . . . . . . .37
BASIC PLAYBACK . . . . . . . . . . . .37
GENERAL FEATURES . . . . . . . . .37
DISC MENU . . . . . . . . . . . . . . . . .37
TITLE MENU . . . . . . . . . . . . . . . . .37
RESUME . . . . . . . . . . . . . . . . . . . .38
PAUSE . . . . . . . . . . . . . . . . . . . . . .38
STEP BY STEP PLAYBACK . . . . .38
FAST FORWARD/REVERSE
SEARCH . . . . . . . . . . . . . . . . . . . .38
SLOW FORWARD / SLOW
REVERSE . . . . . . . . . . . . . . . . . . . .38
C SEARCH FUNCTION . . . . . . . . . . .39
TRACK SEARCH . . . . . . . . . . . . .39
-6-
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 7
FEATURES
TV/VCR Mode
• Hi-Fi system–The Hi-Fi stereo recording system
• 2 Step picture search operation–You can view a
•
• Three different playback tape speeds : SP/LP/SLP
• Two different recording tape speeds : SP/SLP
• Auto Head Cleaner–Automatically cleans video
•
•
offers you excellent sound quality with a dynamic
range of 80dB, frequency response from 20Hz to
20kHz and 0.005% wow and flutter.
Rotary 4-head Record/Playback System–Four heads
ensure excellent picture quality and special effects playback.
Index Search–Fast-forwards to start of next recording.
Slow Motion–View recorded program at slower
than normal speed.
• Infrared remote control
• Trilingual on screen TV/VCR setup display
•
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
heads as you insert or remove a cassette.
• Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
• Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
selectable in English, Spanish or French
Real time counter–This shows the elapsed recording
• Digital Auto Tracking (DTR)–Automatically
or playback time in hours, minutes and seconds. The
“–” indication will appear when the tape is rewound
further than the tape counter position “0:00:00”.
adjusts the tracking for each tape you play.
•
• 181 channel capability PLL frequency synthesiz-
•
be necessary to view scrambled cable channels.)
Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or
text display added to the program.
Auto power on and off system–Automatically
turns on the unit when you insert the cassette, turns
off after auto-rewind and ejects when the beginning of the tape is reached.
•
er tuner with direct station call–(A converter may
•
•
•
•
reached–This function doesn’t occur when using
timer recording.
mode automatically changes without control.
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Let you set the unit to advance the
tape by entering the desired playback time you want
to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
• 1 Year, 8 events (including Daily and Weekly
• Auto rewind when the end of a tape is
• Smooth mode change–TV/VCR mode DVD
Rental play mode–Improves playback picture
•
•
•
•
-7-
Timer Recording)–The built-in timer allows you to
record up to 8 programs at different times on different channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broadcasts and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Auto return–After timer recording is finished, the
unit can return to the beginning of the recording.
Sleep timer–Allows you to have the unit automatically turn off at a desired time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 8
DVD Mode
¡On-screen display
¡Dolby Digital sound
Information about the current operation can be displayed on a TV screen, allowing you to confirm the
currently active functions (such as program playback), on the TV screen using the remote control.
This unit can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby
Digital decoder.
¡Still/fast/slow/step playback
Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
¡Search
Chapter search / Title search / Track search / Time
search
¡Repeat
¡Random playback for Audio CD and MP3
This unit can shuffle the order of tracks to play them
in random order.
Chapter / Title / Track / Group / All / A-B
¡Marker
The part designated by user can be called back.
¡Program playback for Audio CD and MP3
You can program the order of tracks to play them in
any desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input
from the unit for 5 minutes in the stop mode. When the
screen saver program is activated for 15 minutes, the
power automatically turns off.
You can control the range of sound volume.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available
on a disc.
¡Parental lock
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This unit automatically detects if the loaded disc is
DVD, Audio CD or MP3 on disc.
¡Playback MP3 disc
NOTE:
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
-8-
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 9
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - [Fig.1]
DVD buttons
buttons
DVD
1
2
3 4
3
- REMOTE CONTROL -
POWER PICTURE
1
22
23
1
2
3
4
5
6
7
8
27
28
29
30
31
32
33
0
SPEED
CH.
11
VOL.
2
MUTE
STOP
DISC
MENU
DISPLAY
ENTER
SETUP
TITLE
RETURN
CLEAR SEARCH MODE REPEAT
A-B
AUDIO
ANGLE
MODE
SUBTITLE
11 12 13 14 4 15
16 17 18 19
20
21
5. STOP Button [TV/VCR P.26 / DVD P.37]
Stops operation of the disc. (front panel)
Stops operation of the disc or tape contents.
(remote control)
6. OPEN/CLOSE Button [DVD P.37]
Press to insert discs into or remove them from the
tray.
7. Disc loading tray
8. DVD Indicator
Illuminates during DVD mode.
9. SELECT Button
Press to change to TV/VCR mode, external input
mode or DVD mode.
10.TV/VCR Indicator
Illuminates during TV/VCR mode.
11. CHANNEL (CH.) K/L Buttons
Press to select memorized channel.
12. Recording Indicator
Flashes during recording. Illuminates in the Standby mode for Timer Recording.
13. REC/OTR Button (Front Panel) [TV/VCR P.30, 31]
Press to start manual recording. Press repeatedly
to start One Touch Recording (only during
TV/VCR mode).
45
44
PLAY
RECORD
7 8 9 10
SELECT
+10
C.RESET V.SURR
6
[Fig. 2]
9
+100
PAUSE
24
25
26
(DVD) 3
(TV/VCR) 14
4
13
SLEEP
5
TV/VCR buttons
43
42
3 (DVD)
15 (TV/VCR)
5
41
40
39
38
37
36
35
34
RECORD Button (Remote Control) [TV/VCR P.30]
Press to start manual recording.
1. POWER Button [TV/VCR P.15 / DVD P.37]
Press to turn the power on and off.
2. VOLUME (VOL.) X/Y Buttons
Press to control the volume level for the DVD and TV.
3. SKIP/SEARCH Buttons (for DVD)[P.38]
Press once to skip chapters or tracks to a desired
point.
Press and hold to change forward or reverse playback speed.
4. PLAY Button [TV/VCR P.26 / DVD P.37]
Starts playback of the disc or tape contents.
14. REW Button (for TV/VCR) [TV/VCR P.26]
Press to rewind the tape, or to view the picture
rapidly in reverse during playback mode. (Rewind
Search)
15. F.FWD Button (for TV/VCR) [TV/VCR P.26]
Press to rapidly advance the tape, or to view the
picture rapidly in forward during playback mode.
(Forward Search)
16. STOP/EJECT Button [TV/VCR P.28]
Press to stop the tape motion. Press in the Stop
mode to remove tape from the unit.
17. Remote sensor window
18. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
-9-
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 10
- REAR PANEL - [Fig.3]
AUDIO OUT
COAXIAL
ANT.
46 47
48
19. VIDEO input Jack
Connect to the video output jack of a video
camera or VCR.
20. AUDIO L/R input Jacks
Connect to the audio output jacks of a video
camera or VCR.
21. Cassette compartment
22. PICTURE Button
Press to adjust the picture.
23. Number Buttons
TV/VCR Mode: [P.18]
Press two digits to directly access the desired
channel.
Remember to press a “0” before a single digit
channel.
+100 Button–
Press to select cable channels which are equal or
greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 Button–
Press to enter the desired numbers which are
equal or greater than number 10.
24. PAUSE Button [TV/VCR P.26 / DVD P.38]
Pauses the current disc or tape operation.
25. SPEED Button [TV/VCR P.30]
Press to choose the desired recording speed: SP/SLP.
26. C.RESET Button [TV/VCR P.28]
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program.
(See page 33.)
27. DISPLAY Button
30. CLEAR Button
Resets a setting.
31. MODE Button [DVD P.40]
Activates program playback or random playback mode.
32. SEARCH MODE Button [DVD P.39]
Press to locate a desired point.
33. AUDIO Button [DVD P.42]
Press to select a desired audio language or sound
mode.
34. SUBTITLE Button [DVD P.42]
Press to select a desired subtitle language.
35. REPEAT Button [DVD P.40]
Repeats playback of the current disc, title, chapter,
group or track.
36. ANGLE Button (DVD mode) [DVD P.42]
Press to change the camera angle to see the
sequence being played back from a different angle
if available.
37. A-B REPEAT Button [DVD P.40]
Repeats playback of a selected section.
38. RETURN Button
Returns to the previous operation in the DVD
setup mode.
39. ENTER Button
Press to accept a setting.
40. Arrow Buttons
TV/VCR Mode:
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the
display on a TV screen.
TV/VCR Mode:
Display the counter or the current channel number
and current time on the TV screen.
DVD Mode:[P.43]
Displays the current status on the TV screen for
checking purposes.
28. SETUP Button [TV/VCR P.15] [DVD P.44-46]
Press to enter or exit the TV menu or DVD setup
mode.
29. TITLE Button [DVD P.37]
Displays the title menu.
41. DISC MENU Button [DVD P.37]
Displays the menus in the DVD.
42. V. SURR (VIRTUAL SURROUND) Button [DVD P.42]
Sets virtual surround on/off.
43. MUTE Button
Mutes the sound. Press it again to resume sound.
44. SLEEP Button [TV/VCR P.34]
Sets the Sleep Timer.
- 10 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 11
45. SELECT Button
Press to switch TV/VCR and DVD mode. You
can see the mode (TV/VCR or DVD) on the front
panel indicator.
46. ANT. in Jack
Connect to an antenna, cable system or satellite
system.
47. Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect
to a standard AC outlet.
48. COAXIAL digital audio out Jack
Connect to the digital input of an external
amplifier or decoder (for DVD audio only).
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
VHF/UHF Antenna
(Not supplied)
Satellite Box or
Cable Box (Not supplied)
OUT
From Cable
System
From Cable System or
Satellite Dish
IN
75-ohm
Coaxial
Cable
(Not supplied)
VHF Antenna (Not supplied)
UHF Antenna
(Not supplied)
AUDIO OUT
COAXIAL
ANT.
or
VHF/UHF
Combiner
(Not supplied)
ANT.
or
75-ohm Coaxial
Cable (Not supplied)
[Fig. 4]
or
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your unit without a converter box.
By using this connection you can:
1) Use the unit’s remote control to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This unit will ONLY record and view the
same channel.
Flat twin-lead cable
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in the illustration.
By using this connection you can also record scrambled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
remote control. Unattended timer recording is limited
to one channel at a time.
Antenna/Cable Connections
Continued on the Next Page.
- 11 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 12
TO RECORD A SCRAMBLED/UNSCRAMBLED CHANNEL
1.Set the unit’s channel selector to the output channel
of the Cable Converter Box or Satellite Box (Ex.
CH3).
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and in particular, specifies that the cable
ground shall be connected to the grounding system of the building as close to the point of cable
entry as practical.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
When using an external input signal (another VCR or
video camera), connect the player’s audio/video output cables to the AUDIO L/R IN/
AUX
VIDEO IN jacks of your unit. Then
press the CHANNEL button K or
L until “AUX” appears on the
screen.
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on another
source (VCR or video camera), use the AUDIO/
VIDEO input jacks on the front panel.
Connect the audio/video output jacks of another
source to the AUDIO L/R and VIDEO jacks of this
unit.
Then press the CHANNEL button K or L until
“AUX” appears on the screen.
NOTE:
• When you connect a monaural VCR (another
source) to this unit, connect the Audio output jack
of the monaural VCR (another source) to the
AUDIO L jack of this unit. The audio will output
in both L and R channel equally.
To the audio
output jacks
[Another source]
Audio/Video
cable
(not supplied)
etc.
To the video
output jack
[Front of the unit]
[Fig. 5]
- 12 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 13
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cable available at retail for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
AUDIO OUT
COAXIAL
ANT.
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 6]
NOTES:
• The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for the components to be connected to the unit.
• Set Dolby Digital to OFF for audio output in the setup mode. Playing a unit with incorrect settings may
generate noise distortion and may also damage the speakers.
- 13 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 14
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If you use this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a
DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the unit up to a Dolby
Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround
sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
Front speaker
(left)
Center
speaker
Dolby Digital
decoder
Surround
speaker
(left)
Front speaker
(right)
ANT.
To COAXIAL DIGITAL
AUDIO INPUT jack
Surround
speaker
(right)
AUDIO OUT
COAXIAL
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
Subwoofer
[Fig. 7]
NOTES:
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for the components to be connected to the unit.
• If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 45 to set DOLBY DIGITAL to ON.)
• Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup
mode. Playing a unit with incorrect settings may generate noise distortion and may also damage the speakers.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
- 14 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 15
TV/VCR SECTION
SET UP FOR USE
SELECTING THE LANGUAGE
CLOCK SET UP
(AUTO / MANUAL)
TV/VCR
TV/VCR
1
Plug in the power cord
Plug the unit’s power cord into a standard
AC outlet.
NOTE:
• If any digits appear in the corner of the
screen, press the POWER button without unplugging the power cord.
Make sure ...
• Press the SELECT button to select TV/VCR mode
or make sure TV/VCR lights on.
• Press the POWER button to turn on the unit.
NOTE:
This function effects only the language on the screen
menu and not the audio source.
2
Select “LANGUAGE”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “LANGUAGE”.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
MANUAL CLOCK SETTING
Make sure ...
• The unit is turned on.
In the example below, the clock is to be set to:
DATE
May 6th, 2004
SETTING TIME 5:40PM
1
Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “SETTING CLOCK”.
Then press the ENTER button.
Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”
Select “ENGLISH”, “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the ENTER button.
4
The unit’s clock must be set correctly before VCR
timer recording is possible. It is suggested that the
clock be set manually when first setting up the unit,
then set to [ON] the auto clock setting which will
periodically correct the setting if necessary.
NOTE:
If you cannot receive a station with time signals, the
auto clock setting cannot be performed. Use manual
setting only.
2
Select “MANUAL CLOCK SET”
Press the Arrow button K or L to
point to “MANUAL CLOCK
SET”.
Then press the ENTER button.
Exit the Language mode
Press the SETUP button on the remote control to
return to TV mode.
NOTE:
If for some reason the menu is in Spanish or French,
press the SETUP button on the remote control, press
the Arrow button K or L to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then
press the ENTER button, then press the SETUP button on the remote control.
3
Select the day
Press the Arrow button K or L
until your desired day appears.
(Example: 6th → 06)
Then press the Arrow button B.
- 15 -
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
B MANUAL CLOCK SET
D.S.T.
[OFF]
Select the month
Press the Arrow button K or L
until your desired month appears.
(Example: May → 05)
Then press the Arrow button B
(or press the Arrow button { to
go back one step).
4
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– MANUAL CLOCK SET –
MONTH DAY
05 / ––
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
EN
1C29
T0052UC(p1-35).QX3
5
04.9.16
2:13 PM
Select the year
Press the Arrow button K or L
until your desired year appears.
(Example: 2004)
Then press the Arrow button B.
6
Select the hour
Press the Arrow button K or L
until your desired hour appears.
(Example: 5, PM)
Then press the Arrow button B.
7
Select the minute
Press the Arrow button K or L
until the desired minute appears.
(Example: 40)
Page 16
AUTOMATIC CLOCK SETTING
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
THU
2004
MINUTE
–– : ––
––
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
THU
2004
MINUTE
05 : ––
PM
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
THU
2004
MINUTE
05 : 40
8
YEAR
PM
Make sure ...
• The unit is turned on.
• Confirm the unit is receiving a RF (Radio
Frequency) signal from either an antenna or cable
system connection using the ANT. jack on the rear
panel.
NOTE:
• If a cable converter box is being used, make sure it
is powered on.
• You must use the unit’s remote control to perform
the clock setting procedure.
• If the unit is connected directly to a cable converter
box or satellite box, the local PBS station must be
selected on the cable box itself and the unit must
be set to the output channel of the cable converter
box or satellite box (usually channel 3 or 4), to be
able to set up or correct the clock automatically.
1
Start the clock
Press the SETUP button on the
remote control.
Although seconds are not displayed, they begin counting from
00 when you press the SETUP button on the remote control. Use this
feature to synchronize the clock with the correct
time.
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 3 seconds, you may have to
reset the clock.
5:40 PM
2
3
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Set “AUTO CLOCK” to [ON]
Press the ENTER button until
“AUTO CLOCK [ON]” appears.
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow the steps [1] to [2].
2)Select where you want to change using the Arrow
button B.
3)Enter correct numbers using the Arrow button K
or L.
4)Press the SETUP button on the remote control to
start the clock.
Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
– SETTING CLOCK –
B AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
D.S.T.
[OFF]
Begin “AUTO CLOCK CH SEARCH”
Press the Arrow button L to select
“AUTO CLOCK CH SEARCH”.
Press the ENTER button.
• The unit is now searching for the
station which contain the auto
clock set signal. The search for a
signal may take up to 20 seconds
per channel.
• “_ _” appears at the lower left of
the screen when the search has
ended.
• Auto Clock station- write down
the number(s) that appear on the
screen. These are the auto clock
station(s) in your area. See step [4] on page 17.
• If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 15.
Press the SETUP button to exit the screen.
– SETTING CLOCK –
AUTO CLOCK
[ON]
B AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
D.S.T.
[OFF]
– AUTO CLOCK CH SEARCH –
PLEASE NOTE:
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the ENTER button to turn [OFF] this function.
Then you can manually adjust the clock.
- 16 -
08
10
13
__
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 17
NOTE: During Auto Clock CH Search, the picture
may be distorted, this is normal.
DAYLIGHT-SAVING TIME
TV/VCR
4
Enter the channel number that contains the
Automatic Clock Setting Signal
Select this feature and the unit’s clock automatically
will advance one hour in April, then reverse one hour
in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
• First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
• Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
• Press the POWER button to turn on the unit.
Press the SETUP button on the remote control.
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
Press the Arrow button L to select
“AUTO CLOCK CH”.
Press the ENTER button or the
Arrow button { or B until you
locate Auto Clock Set station number. See step [3] on page 16.
Press the SETUP button to exit the
screen.
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH
[ 45]
MANUAL CLOCK SET
D.S.T.
[OFF]
5
1
Turn off the unit
Once the unit is turned off, it will periodically check
and set the correct date and time.
Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “SETTING CLOCK”.
Then press the ENTER button.
2
Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the Arrow button K or L to
point to “D.S.T.”.
Then press the ENTER button until
[ON] appears.
3
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
B D.S.T.
[ON]
Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2] and select [OFF] using the
ENTER button.
- 17 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 18
DELETING (OR ADDING)
CHANNEL(S)
CHANNEL SET UP
TV/VCR
You can program the tuner to scan all the channels
you receive in your area.
NOTE:
Channel memory programming is NOT needed when
connected to a cable box or satellite box. Just select
the unit’s channel selector to the output channel of
the cable box or satellite box (Ex CH3), then select
the channel to be viewed on the Cable Box or
Satellite Box.
Make sure ...
• Press the POWER button to turn on the unit.
1
TV/VCR
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
1
2
Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then press the ENTER button.
2
3
Select “ADD/DELETE CH”
Press the Arrow button K or L to
point to “ADD/DELETE CH”.
Press the ENTER button.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
3
Begin auto ch programming
Press the Arrow button K or L to
point to “AUTO CH PROGRAMMING”.
Then press the ENTER button.
The tuner scans and memorizes all
the active channels in your area.
Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then press the ENTER button.
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
Enter the desired channel number
Press the Arrow button K or L
until your desired channel number
08
appears. (You can also use the
number buttons or the CHANNEL
button K or L to enter it)
(Example: CH8)
• You must precede single-digit channel numbers
with a zero (Example: 02 ... 09).
• When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
ADD / DELETE
After scanning
The tuner stops on the lowest memorized channel.
• When AUTO CH PROGRAMMING is activated
where there is no TV signal input, “NO TV SIGNALS” will appear on the display after the completion of the channel scanning.
• The unit may recognize TV channels to be CATV
channels by the receiving conditions. In this case,
try AUTO CH PROGRAMMING again in the fine
receiving conditions.
4
Delete (or add) it from (or into) memory
Press the ENTER button. The channel number
changes to light red. The channel is deleted from
memory.
• To delete another channel, repeat steps [3] to [4].
• If you press the ENTER button again, the channel
is memorized again.
Added channel: Light blue
Deleted channel: Light red
5
Exit the channel setup mode
Press the SETUP button on the remote control to
return to TV mode.
NOTE:
To confirm that channel(s) has been deleted or
added, press the CHANNEL button K or L.
- 18 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 19
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
TV/VCR
1
Turn on the unit
Press the POWER button to turn on the unit.
2
Select the channel number
Press the CHANNEL button K or L to select your
desired channel number or press the number on the
remote control.
Note for using the Number button on the remote
control:
¡You must precede single-digit channel numbers
with a zero (For example: 02, 03, 04 and so on).
¡When selecting cable channels which are higher
than 99, press +100 first, then, press the last two
digits. (Example: to select channel 125, first press
“+100” then press “2” and “5”).
Remember: If the unit is connected to a cable box or
satellite box, the unit must be on CH3 or CH4, then
the channel to be viewed must be selected on the
cable box or satellite box.
3
Adjust sound
TV/VCR
The unit’s picture controls – BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a more natural looking image.
NOTES:
• Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
Make sure ...
• The unit must be turned on.
1
Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
2
Select item you want to adjust
Press the Arrow button K or L until desired control
is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
BRIGHT
–PPPPPPPCPPPPPPP+
Press the VOLUME button X or Y
to adjust the volume.
3
VOLUME
20
C C C C C CCCCCCC
NOTES:
• If you press the CHANNEL button K or L in the
DVD mode, you can change the TV channels.
Even if you turn off the unit in the DVD mode, it
will go into the TV/VCR mode when you turn it on
again.
COLOR
Arrow button s
to decrease
brightness
to decrease
contrast
to pale
TINT
SHARPNESS
to purple
to soft
BRIGHT
CONTRAST
DEGAUSSING
TV/VCR
Magnetism from nearby appliances and speakers
might affect the color of the TV picture.
If this happens, move this unit away from the appliance. If the color is still not correct, unplug the
power cord, then plug it in again 30 minutes later or
so.
Adjust the picture control
Press the Arrow button { or B to adjust to your
desired level.
Arrow button B
to increase
brightness
to increase
contrast
to brilliant
to green
to clear
• If there is a power failure of any kind, the unit
will retain its memory for this feature.
- 19 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 20
CLOSED CAPTION SYSTEM
1
TV/VCR
You can view specially labeled (cc) TV programs,
movies, news and pre-recorded tapes with either a
dialogue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CAPTION”.
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select your desired caption menu
Press the ENTER button until your
desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
3
NOTE:
Not all programs are broadcast with closed captions.
Your unit is designed to provide error free closed
captions from high quality antenna, cable and VCR
signals. Conversely, poor quality signals are likely to
result in caption errors or no captions at all. Common
signal conditions which may cause caption errors are
listed below:
• Automobile ignition noise
• Electric motor brush noise
• Weak snowy reception on TV screen
• Multiplex signal reception displaying picture
ghosts or airplane flutter.
• Playback of poorly recorded or worn VCR tapes.
NOTE:
If the unit displays a black box on
the TV screen, this means that the
unit is set to the TEXT mode. To
clear screen, select [CAPTION1],
[CAPTION2] or [OFF].
Select “CAPTION”
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Exit the caption setting mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] to [2] and select [OFF] using the
ENTER button. Press the SETUP button on the
remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 seconds.
• It will also disappear when the MUTE button or
the PAUSE button is pressed while recording.
• If there is a power failure of any kind, the unit will
retain its memory for this feature.
Make sure ...
• The unit is turned on.
- 20 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 21
V-CHIP SET UP SUB RATINGS
V-CHIP SET UP
TV/VCR
V-CHIP SET UP
1
Make sure ...
• The unit is turned on.
1
Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”.
Then press the ENTER button.
2
Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
Then press the ENTER button.
4
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”.
Then press the ENTER button.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Enter Access code
ACCESS CODE
Use the number buttons on the
remote control to enter the access
code. (Default code is 0000.)
_ _ _ _
ACCESS CODE
3
_ _ _ _
Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
Then press the ENTER button.
– V-CHIP SET UP –
4
B TV RATING
MPAA RATING
CHANGE CODE
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
Selecting Sub-Ratings
Press the Arrow button K or L to select the sub-rating you wish to block. Then press the ENTER button
twice.
• When you select [TV-Y7]:
Press the Arrow button K or L to
select “FV” (Fantasy Violence).
Then press the ENTER button to
select [BLOCK] or [VIEW].
When
you select [TV-PG],
•
[TV-14] or [TV-MA]:
Press the Arrow button K or L to
select “D”(Suggestive Dialog),
“L”(Coarse Language),
“S”(Sexual Situation) or
“V”(Violence). Then press the
ENTER button to select [BLOCK] or [VIEW].
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
• The sub-ratings which are set to
[BLOCK] appears next to the rating category in the TV rating
menu.
TV–Y7
Blocking TV programs
B FV
Press the Arrow button K or L to
select “TV rating” that you wish to
block.
Press the ENTER button to set it
[BLOCK].
•When you select the rating category and set it to
[BLOCK], the higher rating will change to
[BLOCK] automatically. Also, the lower rating will
change to [VIEW] automatically.
• When you set “TV-Y” to [VIEW], then all ratings
will change to [VIEW] automatically.
B TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
)
)
)
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
Selection
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
Rating Category Explanations
Appropriate for all children
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
TV-MA
Mature audience only
5
Select “V-CHIP SET UP”
Enter Access code
Use the number buttons on the remote
control to enter the access code.
• For the first time set-up or in the
event the unit has lost power,
enter the default code of the numbers: 0000.
3
When you select the ratings of TV-Y7,TV-PG,TV-14
or TV-MA you will have the option of selecting sub
rating categories.
[BLOCK]
[BLOCK]
TV–PG
5
[BLOCK]
B D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
TV–Y
TV–Y7 (
)
TV–G
B TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
enter the setting and exit the screen.
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
- 21 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 22
CHANGING V-CHIP BLOCKED PROGRAMMING
Note: To change the rating, the TV must be turned to
a station that is not protected. If the (PROTECTED)
appears on the screen, please change the channel to a
station that is not protected.
1)Follow steps [1] to [2].
2)Press the Arrow button K or L to select “TV RATING, then press the ENTER button. Select a TV
rating to be unblocked by pressing the Arrow button K or L.
Then press the ENTER button to unblock the rating.
3)Press the SETUP button on the remote control to
exit the screen.
5
CHANGE ACCESS CODE
To change access code, follow the steps below.
1
1
Select “V-CHIP SET UP”
2
Enter Access code
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
ACCESS CODE
Use the number buttons on the
remote control to enter the access
code.
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP
SET UP”.
Then press the ENTER button.
MPAA RATING SET UP
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”.
Then press the ENTER button.
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
Enter Access code
Use the number buttons on the remote
control to enter the access code.
The default code is 0000.
3
Select “CHANGE CODE”
Press the Arrow button K or L to
select "CHANGE CODE".
Then press the ENTER button.
ACCESS CODE
_ _ _ _
– V-CHIP SET UP –
TV RATING
MPAA RATING
B CHANGE CODE
_ _ _ _
4
Enter New code
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
• If you enter wrong code, repeat step [4], making
sure you enter the same new code exactly in the
confirm code space.
NEW CODE
3
Select “MPAA RATING”
Press the Arrow button K or L to
point to “MPAA RATING”.
Then press the ENTER button.
4
– V-CHIP SET UP –
XXXX
TV RATING
B MPAA RATING
CHANGE CODE
CONFIRM CODE
_ _ _ _
Select your desired item
Press the Arrow button K or L to
point to your desired item.
Then press the ENTER button to
select [BLOCK] or [VIEW].
Selection
G
PG
PG-13
R
NC-17
X
G
PG
PG–13
B R
NC–17
X
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompanying parent or adult guardian
No one under 17 admitted
Mature audience only
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
NOTE:
If you unplug the power cord or a power failure
occurs, the changed access code will be lost and will
return to default (0000). Change your access code
again as necessary.
• When you select the rating category and set it to
•
[BLOCK], the higher rating will change to
[BLOCK] automatically. Also, the lower rating
will change to [VIEW] automatically.
When you set “G” to [VIEW], then all ratings will
change to [VIEW] automatically.
- 22 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 23
MTS (Multi-Channel Television sound) SYSTEM
You can record or listen to a program in MTS stereo.
CHECKING THE SELECTED MTS MODE
TV/VCR
When you play a VHS tape or receive a broadcast on
the unit’s tuner channel you are watching, the status
shown below will appear when you press the DISPLAY button on the remote control.
4)
PLAY B
HIFI
12:00AM
CH 123
STEREO/SAP
3)
2)
1)
SP
COUNT
0:00:00
SAP
Second Audio Program, which means your
program, can also be received in a second
language or sometimes a radio station.
HIFI
High Fidelity which produces better sound
than standard stereo units.
1) When a program is broadcast in stereo, STEREO
appears on the TV screen.
2) When a program is broadcast in second audio,
SAP appears on the TV screen.
3) When a program broadcast both in stereo and second audio, “STEREO” and “SAP” appear on the
TV screen.
NOTE: Although a program may be broadcast in
both stereo and second audio, you cannot
record in both stereo and second audio at
the same time.
4) While the unit is set in HIFI stereo mode and
playback mode, “HIFI” appears on the TV screen.
While the unit is set in monaural (MONO) mode,
“HIFI” disappears from the TV screen.
NOTE: If you play non-HIFI tapes while the unit is
set in HIFI, “HIFI” will disappear from the
TV screen and the unit will automatically
play in monaural.
MTS RECORDING/MONITOR MODE
TV/VCR
Type of broadcast
Regular
(monaural audio)
Stereo broadcast
Bilingual broadcast
Display on
the TV screen
-None-
STEREO/SAP
SELECTION
-Invalid-
STEREO
SAP
-InvalidSTEREO*
L
Main audio
program
Sub audio
program
L
sub audio
program
SAP*
Stereo & Bilingual
broadcast
STEREO
SAP
Hi-Fi audio track (2-channel)
L-channel
R-channel
Mono
Mono
STEREO*
SAP*
R
Main audio
program
Sub audio
program
R
sub audio
program
Normal audio
track
Mono
L+R
Main audio
program
Sub audio
program
L+R
sub audio
program
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 23 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 24
SELECTING THE MTS SYSTEM
TV/VCR
TO SELECT MONO MODE
Make sure ...
• The unit is turned on.
You can change the selection to “MONO” if you
want to listen to HIFI tapes in normal audio playback.
1) Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S
SET UP”. Then press the ENTER button.
2) Press the Arrow button K or L to point to
“VCR AUDIO”.
3) Press the ENTER button until [MONO] appears.
4) Press the SETUP button on the remote control to
return to TV mode.
TO SELECT HIFI MODE
1
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then press the ENTER button.
2
Select “VCR AUDIO”
Press the Arrow button K or L to
point to “VCR AUDIO”.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
TO SELECT [STEREO], [SAP] OR [MONO]
1
3
Select [HIFI]
Press the ENTER button until
[HIFI] appears.
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
2
4
Select “USER’S SET UP”
Select “TV AUDIO”
Press the Arrow button K or L to
point to “TV AUDIO”.
To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
• Normally “HIFI” should be selected for playback
with HIFI sound.
• When you play non-HIFI tapes, the unit will automatically play in the monaural mode.
• The unit records automatically MTS broadcasts in
HIFI stereo sound unless you select [SAP] before
recording.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
B TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
Select [STEREO], [SAP] or [MONO]
Press the ENTER button until [STEREO], [SAP] or
[MONO] appears.
4
To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
• You must select the recording mode,either TV
AUDIO [STEREO] or [SAP] when you record a
broadcast.
(Refer to MTS RECORDING/MONITOR MODE
on page 23.)
If
• you select [SAP] when second audio is not available, the unit will record normal audio.
• The unit records automatically MTS broadcasts in
HIFI stereo sound unless you select [SAP] before
recording.
- 24 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
4:23 PM
Page 25
VIDEO CASSETTE
This unit will operate with any cassette that has the
mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
• Avoid moisture. Moisture condensation may occur
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the unit. The unit will
automatically turn on.
•
•
•
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your unit, wait until the tape has warmed to room
temperature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
Window
WRONG
CORRECT
TWO DIFFERENT TAPE SPEEDS
REMOVING A CASSETTE
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each
mode.
1)In the Stop mode, press the STOP/EJECT button
on the unit. The cassette will be ejected.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
Tape Speed
Type of tape
Recording/Playback Time
T60
T120
T160
SP mode
1 hour
2 hours
2-2/3 hours
SLP mode
3 hours
6 hours
8 hours
NOTE:
You can play back a tape recorded in LP mode (Long
Play).
ERASE PREVENTION
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Plastic Tape
NOTE:
• In DVD mode, whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
you press the PLAY button.
In TV/VCR mode, if the cassette without tab is
inserted, playback will automatically start.
- 25 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 26
PLAYBACK
NORMAL PLAYBACK
TV/VCR
Make sure ...
• The unit is turned on.
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the unit
will start playback automatically.
2
To begin playback
PLAY B
Press the PLAY button.
3
To stop playback
STOP
Press the STOP button when playback is completed.
NOTES:
• If you press the PLAY button (of the TV/VCR side)
in the DVD mode, you can start the VCR playback.
• If you press the SELECT button during the VCR
playback, it will stop and the mode will change to
the DVD mode. In addition, the same function
operates with the DVD side PLAY button or the
OPEN/CLOSE button.
TRACKING ADJUSTMENT
TV/VCR
• Tracking adjustment will be set automatically
(Digital Tracking function) when you start playback.
• However when playing pre-recorded tapes or tapes
•
PICTURE SEARCH
recorded on other VCR, noise lines (black and white
streaks) may appear on the playback picture. If this
occurs, you can adjust the tracking control manually
by pressing the CHANNEL button K or L until the
streaks disappear. To return to the DTR function,
stop the tape once and start playback again.
You can reduce the noise lines by pressing the
CHANNEL button K or L in slow mode too.
Tracking adjustment in Slow mode will not be set
automatically.
SLOW MOTION
TV/VCR
TV/VCR
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD g or REW h button during playback. (in SP / LP / SLP modes)
NOTE:
• If you press the F.FWD or REW button on the front
panel in the DVD mode, the VCR forward or
reverse will start. Please press the STOP/EJECT
button once to stop it, twice to eject it.
2)Press it again and the unit will now search in super
high speed. (in the LP / SLP modes only)
NOTE:
• Tapes recorded in SP or LP mode will display a
noise bar on the TV screen and the picture may
revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
STILL PICTURE
TV/VCR
You can view a still picture on the TV screen during
playback (the Still mode). Press the PAUSE button
during playback. Only tapes recorded in SLP mode
will show the least amount of lines. Press the PLAY
button to return to playback.
NOTES:
• You can advance the picture one frame at a time by
pressing the PAUSE button during Still mode.
• If it is left in the Pause mode for more than 5 minutes, the unit will automatically switch to Stop
mode.
VERTICAL HOLD CONTROL
TV/VCR
In Pause/Still mode only, when the picture begins to
vibrate vertically, stabilize the picture by pressing the
CHANNEL button K or L.
NOTE:
If there are video noise lines on the screen, see
TRACKING ADJUSTMENT.
Press the PAUSE button, then press the F.FWD g
button to start the playback in slow motion. The unit
mutes the sound during slow motion. Press the PLAY
button to return to normal playback.
NOTE: If it is left in Slow mode for more than 5 minutes, the unit will automatically go into Stop mode.
- 26 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 27
SPECIAL PLAYBACK
Make sure ...
• The unit is turned on.
• Insert a prerecorded tape.
AUTO REPEAT PLAYBACK
TV/VCR
RENTAL PLAYBACK
TV/VCR
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then press the ENTER button.
2
Set “RENTAL” to [ON]
Press the Arrow button K or L to
point to “RENTAL”.
Press the ENTER button until [ON]
appears.
3
The unit has the auto repeat function that allows you
to repeat a tape indefinitely without touching the
PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
1
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
B RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[ON]
[OFF]
[OFF]
[HIFI]
[STEREO]
Exit the Rental setting
2
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
• Once you select the Rental mode, it stays in effect
even after you turn off the unit.
TO CANCEL THE RENTAL MODE
Repeat steps [1] to [2] and select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
Select “ALL” or “BLANK”
Press the Arrow button K or L to
point to “REPEAT PLAY”.
Press the ENTER button repeatedly
until your desired selection [ALL]
or [BLANK] appears.
Press the SETUP button on the remote control to
return to the TV mode.
4
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”, then
press the ENTER button.
3
– USER’S SET UP –
RENTAL
B REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[ALL]
[OFF]
[HIFI]
[STEREO]
Exit the Repeat Play setting
Press the SETUP button on the remote control to
return to the TV mode.
4
Start playback
Press the PLAY button to start the Repeat Play.
“REPEAT PLAY B” appears.
• Once you select Repeat Play mode, it stays in
effect even after you turn off the unit.
• If Rental Play mode is set to [ON], “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] to [2] and select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
- 27 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 28
SEARCH
Make sure ...
• The unit is turned on.
• Insert a tape.
TIME SEARCH
TV/VCR
ZERO RETURN
TV/VCR
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2
The Time Search function makes it possible to quickly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
NOTES:
• Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
• This function will not operate in recording mode.
• This function is not operative when a cassette tape
is not inserted in the unit.
In the example below: To watch a program before/
after 2 hour 50 minutes from the present position, in
either direction.
Reset the counter to 0:00:00
Press the C.RESET button repeatedly.
3
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
4
To activate “ZERO RETURN” mode
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “ZERO RETURN”.
Then press the ENTER button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter
returns to 0:00:00.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B ZERO RETURN
TIME SEARCH
INDEX SEARCH
1
Insert a tape
2
Select “TIME SEARCH” mode
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “TIME SEARCH”, then
press the ENTER button.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
Enter your desired time
Press the Arrow button K or L
until your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time
Search at this point, press the SETUP button on the
remote control.
TIME SEARCH
2 : 50
4
Begin Time Search
By pressing the Arrow button s or B, the unit will
rewind or fast forward to the specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the unit or the
STOP button on the remote control. This will delete
the selected time.
- 28 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 29
INDEX SEARCH
1
TV/VCR
This feature provides a method of indexing the starting point so that it can be easily returned to in either
fast forward or rewind mode.
• The index mark will be made automatically when
the RECORD button is pressed. It will also be
marked at the starting point of Timer recording and
OTR.
• The index mark will not be recorded if the PAUSE
button is pressed and released during recording.
• The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 minutes for SLP recording.
• In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
CURRENT PLAYBACK PROGRAM
Beginning of tape
Pro.1
4
Pro.2
3
2
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “INDEX SEARCH”.
Then press the ENTER button.
2
Pro.4
1
Pro.5
1
Pro.6
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
Enter your desired number
Press the Arrow button K or L until
the number of programs that you
want to skip appears.
(Example: “03” for 3 programs)
• The Index Search mode will be
canceled if the procedures are not activated in 30
seconds.
INDEX SEARCH
03
3
Begin Index Search
Press the Arrow button s or B. The unit begins
rewinding or fast forwarding to the beginning of
desired program.
NOTE: Every time an index signal is skipped, the
number in the program indicator decreases by one.
4
End of tape
Pro.3
Select “INDEX SEARCH”
After Index Search
When the preset program is reached, the unit will
start playback automatically.
• A video cassette must be inserted in the unit for
this function to work.
• The number of Index Searches can be set up to 20.
• This function will not operate in the recording mode.
• When you want to cancel the Index Search while
in progress, press the STOP button.
Pro.7
3
INDEX MARK
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
TV/VCR
TV/VCR
This shows the elapsed recording or playback time in
hours, minutes and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.) The “–” indication will appear when the tape
has rewound further than “0:00:00” on the tape
counter.
• When the end of a tape is reached during record-
•
•
- 29 -
ing, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding
finishes, the unit will eject the tape and turn itself
off.
This function is operative when Repeat Play is set
to [OFF].
The tape will not auto-rewind during timer recording or One Touch Recording.
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 30
RECORDING
Make sure ...
• The unit is turned on.
• Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
• This unit will ONLY record and view the same channel.
• This unit cannot record the contents from the built-in DVD.
SKIPPING UNWANTED
SCENES DURING RECORDING
NORMAL RECORDING
TV/VCR
You can ONLY watch the same TV program that is
being recorded.
1
PAUSE
Select the channel to be recorded
Press the number buttons on the
CH 10
remote control or the CHANNEL
button K or L.
Remember: If the unit is connected
to a cable box or satellite box, the
unit must be on CH3 or CH4, then
the channel to be recorded must be selected on the
cable box or satellite box.
2
TV/VCR
Press the PAUSE button to temporarily stop recording.
Press the PAUSE or RECORD button to resume recording.
NOTES:
• After 5 minutes, the unit will
automatically switch to Recording mode to prevent
tape damage.
• If “CLOSED CAPTION (ON)” is selected, the OnScreen Display will appear for 5 seconds, then disappear.
SP
Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
SP
3
Begin recording
REC
Press the RECORD button.
SP
4
Stop recording
Press the STOP button when recording is completed.
- 30 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 31
OTR (One Touch Recording)
TV/VCR
This function enables you to set a recording length
simply by pressing the REC/OTR button on the unit.
Make sure ...
• The unit is turned on.
• Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape
to the point at which you want to begin recording.)
NOTES:
• You CANNOT start OTR with the remote control.
• Recording starts immediately when the REC/OTR
button is pressed.
• When the REC/OTR button is pressed 18 times,
the unit returns to the Normal Recording mode.
• To stop the OTR operation, press the STOP button
on the unit or on the remote control.
• To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up
momentarily then disappear.)
• Recording stops when 0:00 is reached.
• Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120).
• If the tape runs out before the end time, the unit
will switch to the Stop mode immediately, ejects
the tape and turns itself off.
• If you press the POWER button during OTR, the
unit continues recording until the selected length is
reached.
1
2
Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3
Begin OTR
Press the REC/OTR button on the
unit as many times as needed. The
recording length will be determined
by the number of times you press the
REC/OTR button. Each additional
push will increase the recording time
by 30 minutes. It is set up to 8 hours.
OTR(2 : 30)
SP
Display
17 pushes
8:00
0:30
1:00
Recording length
(normal recording)
30 minutes
60 minutes
480 minutes
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
TV/VCR
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your unit and a source (playing) VCR using
the following diagram.
[Fig.8]
[This unit]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL button K or L.
Remember: If the unit is connected to a cable box
or satellite box, the unit must be on CH3 or CH4,
then the channel to be recorded is selected on the
cable box or satellite box.
Push(es)
1 push
2 pushes
3 pushes
AUDIO
L
IN
OUT
R
VIDEO
OUT
IN
1)Insert a pre-recorded video cassette into the source
(playing) VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the unit’s cassette compartment.
3)Press the SPEED button on remote control to select
the desired recording speed (SP/SLP).
4)Press the CHANNEL button K or L on the unit
until “AUX” appears on the screen.
5)Press the RECORD button on the unit.
6)Begin playback of the tape in the source (playing)
VCR or camcorder.
NOTE:
For best results during copying, use the unit’s front
panel controls whenever possible. The remote control
might affect the source (playing) VCR’s playback
operation.
7)To stop copying, press the STOP/EJECT button on
the unit, then stop the tape on the source VCR or
camcorder.
- 31 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 32
TIMER
AUTOMATIC TIMER
RECORDING
1
Select “TIMER PROGRAMMING”
Press the SETUP button on the
remote control.
Confirm “TIMER PROGRAMMING” is pointed by pressing the
Arrow button K, then press the
ENTER button.
• If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow steps [3] to
[8] on pages 15 and 16 before setting the timer
recording.
- TV/VCR SETUP -
TV/VCR
You may set the unit to start and end a recording
while you are away. You can set 8 programs to record
on specific days, daily or weekly within a 1 year
period.
In the example below, the timer is being set to record:
DATE:
July 4th, 2004
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
CH61
TAPE SPEED:
SP
Make sure ...
• If a cable box or satellite box is connected with the
unit you will be limited to record only one channel
and the channel selector on the unit must be selected to the output channel of the boxes CH 3 or CH
4 and then the actual channel to be recorded must
be selected on the boxes.
• Clock must be set to the correct time and date
before setting the timer.
• The unit’s power must be turn on to program it.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
• The channel you want to record is properly set in
advance. (See page 18.)
Avoid over lap of programs ...
There is a chance that a program will not be recorded. when programs overlap;
• The program with an earlier start has priority.
• Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
• When the starting time is the same, a program set
previously has priority.
• The illustration below demonstrates the sequence
of recordings.
Program 1
10:00AM - 11:00AM
Program 2
9:00AM - 10:00AM
Program 3
9:30AM - 12:00PM
B TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired program position (1 to 8)
Press the Arrow button K or L to
select the desired program position,
then press the Arrow button B.
3
B -
-
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
-
-
Set the channel number
– TIMER PROGRAMMING –
Press the Arrow button K or L
until the desired channel number
appears (Example: CH61), then
press the Arrow button B.
Remember: If the unit is connected
to a cable box or satellite box, the unit must be on
CH3 or CH4, then the channel to be recorded is
selected on the cable box or satellite box.
CH DATE
---B 61
-----
4
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Select once, every day or weekly recording
For once recording :
Press the Arrow button K (up)
until the desired date appears
(Example: “7/04” for July 4th),
then press the Arrow button B.
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 7/04 SUN -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
For every day recording : To record
a TV program at the same time on the same channel
every day. (Example: Monday through Sunday)
Press the Arrow button L (down)
until “EVRY DAY” appears,
then press the Arrow button B.
Recording Sequence
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY DAY -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
For weekly recording : To record a
TV program at the same time on the same channel
every week. (Example: every
Monday)
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM
– TIMER PROGRAMMING –
CH DATE
– TIMER PROGRAMMING –
10:00AM
11:00AM
CH DATE
12:00PM
Press the Arrow button L (down)
until “EVRY” and your desired
day of the week appear together,
then press the Arrow button B.
*Recording period is SHADED
- 32 -
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
EN
1C29
T0052UC(p1-35).QX3
5
04.9.16
2:13 PM
Set beginning hour
Press the Arrow button K or L
until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then press the Arrow button B.
6
Set beginning minute
Press the Arrow button K or L
until the desired minute appears.
(Example: “30” for 7:30PM)
Then press the Arrow button B.
7
Set end hour
Press the Arrow button K or L
until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then press the Arrow button B.
8
Set end minute
Press the Arrow button K or L
until the desired minute appears.
(Example: “50” for 8:50PM)
Then press the Arrow button B.
Page 33
TIMER PROGRAM EXTENSION
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 SUN 7:12 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
-
-
-
-
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 SUN
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:-:-:-:-:-:-:-:-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 SUN 7:30 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:- - - -:- - - -:- - - 8:30PM- -:- - - -:- - - -:- - - -:- - - -
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
61
7/04
SUN
7:30
M
8:50
M- B
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
TV/VCR
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
2)Repeat step [1] on page 32.
3)Press the RECORD button and select the desired
program using the Arrow button K or L.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the PAUSE button on the remote control. The recording time
returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automatically be set to the SLP mode.
5)Press the ENTER or RETURN button to exit the
setting menu. Then press the SETUP button on the
remote control to return to original mode.
TO CORRECT A PROGRAM
9
Set the tape speed
Press the Arrow button K or L
until the desired tape speed
appears. (Example: SP)
10
• While setting a program; press the Arrow button
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 SUN
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:- - - -:- - - -:- - - 8:50PM SP
-:- - - -:- - - -:- - - -:- - - -
•
Finish setting the program
Press the ENTER or RETURN button. The program
is now completed.
• To set another program, repeat steps [2] to [10].
• Press the SETUP button on the remote control to
return to original mode.
11
Set the timer
Press the POWER button to set automatic timer
recording. The Recording indicator illuminates.
• You must turn off the unit to activate automatic
timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing
on the TV screen for 2 minutes before the programmed start time.
s to go back one step and enter the correct numbers using the Arrow button K or L.
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] to [2] on page 32.
3)Press the Arrow button B (or press the Arrow
button s to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the Arrow button K or L.
4)Press the POWER button to set automatic timer
recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
• After setting a program;
•
- 33 -
1)Press the POWER button.
2)Repeat steps [1] to [2] on page 32 and select a
program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to
return to TV mode.
While recording is in progress;
1)Press the POWER button.
2)Press the STOP/EJECT button on the unit.
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 34
TO CHECK THE BEGIN/END TIME
3
1)Press the POWER button so that the Recording
indicator turns off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the ENTER button. The details of programs
appear on the TV screen.
5)Press the SETUP button on the remote control to
return to TV mode.
4
TV/VCR
• Make sure the channel you want to record is prop•
•
•
•
•
erly set in advance.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
The display will not be turned on when the programmed
recording begins. To watch the currently recorded TV
program or to play a DVD disc, press the POWER button to turn on the display and use the SELECT button to
choose the TV/VCR mode or the DVD mode.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette will
be ejected when the POWER button is pressed to off.
If the tape runs out before the end time, the unit
will switch to the Stop mode immediately and the
tape will be ejected.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] to [2], select [OFF] using the
ENTER button.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
SLEEP TIMER
TV/VCR
The Sleep Timer function turns off the unit without
using the POWER button after a desired period of
time.
NOTE:
• This function does not operate during Recording
mode.
1
TV/VCR
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then press the ENTER button.
2
2
Set sleep time
Press the SLEEP button until your
desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, the Sleep Timer setting will disappear automatically.
SLEEP 120 MINUTES
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TO CANCEL THE SLEEP TIMER
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button
until “SLEEP 0 MINUTES” appears.
Set “AUTO RETURN” to [ON]
Press the Arrow button K or L to
point to “AUTO RETURN”.
Press the ENTER button until [ON]
appears.
Select “SLEEP TIMER”
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
AUTO RETURN
1
Watch the recorded program
Press the PLAY button.
HINTS FOR AUTOMATIC
TIMER RECORDING
•
Auto Return will begin
When all the timer recordings are completed, the unit
will rewind to the beginning of the recorded program(s).
NOTE:
• If you press the POWER button while tape is
rewinding, the Auto Return will stop.
– USER’S SET UP –
RENTAL
REPEAT PLAY
B AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[ON]
[HIFI]
[STEREO]
- 34 -
EN
1C29
T0052UC(p1-35).QX3
04.9.16
2:13 PM
Page 35
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
When the Closed Caption mode is ON:
• Counter mode: After 5 seconds, only the counter
• The On Screen Display will disappear after 5 sec-
remains. To clear it, press the DISPLAY button.
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, press
the DISPLAY button.
• This is true even if the MUTE button is pressed or
•
OFF mode
Counter mode
the PAUSE button is pressed while recording.
OFF mode
Clock mode
STOP
SP
onds.
STOP
COUNT 0:12:34
Clock/Counter mode
5:40PM
CH2
STOP
5:40 PM
CH2
SP
After 5 seconds
After 5 seconds
SP
COUNT 0:12:34
5:40PM
CH2
COUNT 0:12:34
Counter
remains
Clock & Channel
remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
5A
2
3
4
5
6
7
8
9
10
11
12
13
A
B
TV Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CATV channel
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
TV Display
CATV channel
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
TV Display
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CATV channel W+10
TV Display
46
CATV channel W+25
TV Display
61
CATV channel W+40
TV Display
76
CATV channel W+55
TV Display
91
CATV channel W+65
TV Display
106
CATV channel W+80
TV Display
121
W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
47
48
49
50
51
52
53
54
55
56
57
58
59
60
W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
62
63
64
65
66
67
68
69
70
71
72
73
74
75
W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
77
78
79
W+56 W+57 W+58
92
93
94
80
81
82
83
84
85
86
A-5
A-4
A-3
A-2
A-1
W+59 W+60 W+61 W+62 W+63 W+64
95
96
97
98
99
100
101
87
102
88
103
89
104
90
105
W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
107
108
109
110
111
112
113
114
115
116
117
118
119
120
W+81 W+82 W+83 W+84
122
123
124
125
- 35 -
EN
1C29
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 36
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this unit.
¡DVD video
¡DVD-R/RW*
¡DVD+R/RW*
¡Audio CD
¡CD-R/RW*
¡MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
[DVD]
Data on a DVD is divided into sections called “titles”
and then into subsections called “chapters”, each of
which is given a title or chapter number. Playback conditions are preset on some DVD video discs and these
playback conditions take priority over user operations on
this unit. If a function you selected does not run as
desired, refer to the manual accompanying the disc.
• Some DVD-R/RW, DVD+R/RW or CD-R/RW discs
made on personal computers or on DVD recorders may
not be played back properly due to the factors such as
scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played
back properly due to the different environment or the
settings of the application you use. We recommend
always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
This unit conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡Some discs include region codes as shown below.
Example
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
[AUDIO CD]
Data on an Audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world and a disc encoded in a specific region format
can only be played back on a unit with the same region
code.
The following discs cannot be played back on this unit.
¡DVD with region codes other than 1 or ALL
¡DVD-ROM
[MP3]
Data on an MP3 is divided into sections called “groups”,
and then into subsections called “tracks”, each of which
is given a group or track number.
¡DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Example
Group 1
¡CD-ROM
Track 1
¡VSD
Track 2
Track 3
Group 2
Track 4
Track 5
Track 6
¡CDV (Only plays back the audio part)
¡CD-G (Only plays back the sound)
¡CD-I (Never play back, otherwise malfunction
may result.)
¡SACD
¡Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡Video CD (Never play back, otherwise malfunc-
tion may result.)
¡DTS-CD
And any other discs without compatibility indications
– 36 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 37
PLAYING A DISC
BASIC PLAYBACK
DVD-V
CD
GENERAL FEATURES
MP3
DVD-V
Getting started
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1 Press the POWER button.
¡The power will turn on.
2 Press the OPEN/CLOSE button to open disc
loading tray.
3 Place the chosen disc in the tray, with the
label facing up.
DVD may contain menus to navigate the disc and
access special features. Press the appropriate number
buttons or use the Arrow button (K/ L/s/ B) to highlight your selection in the DVD main menu and press
the ENTER button to confirm.
NOTES:
¡Select DVD mode by pressing the SELECT button on
the remote control. Then operate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
DISC MENU
DVD-V
1 Press the DISC MENU button.
¡The DVD main menu will appear.
4 Press the PLAY button.
¡The tray will close automatically and playback will
2 If the feature is not available,
symbol
may appear on the TV screen.
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
the PLAY button.
¡When you playback a DVD which features a title
menu, it may appear on the screen. In this case,
refer to “TITLE MENU”.
3 If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selection.
4 Press the Arrow button (K/ L/s/ B) to
select an item and the ENTER button to
confirm selection.
5 Press the STOP button to stop playback.
NOTES:
¡When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and
then the TV picture and sound appears in about 4
seconds. Similarly, when the POWER button is
pressed to turn off in the DVD mode, this mode shuts
down first and then the unit’s power is turned off.
¡A “prohibited icon” may appear
at the top-right on the TV screen
during operation, warning that a
prohibited operation has been
encountered by the DVD or the
disc.
¡With DVDs that use titles for playback program
signals, playback may start from the second title or
it may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a malfunction.
TITLE MENU
DVD-V
1 Press the TITLE button.
¡The title menu will appear.
2 If the feature is not available,
symbol
may appear on the TV screen.
3 Press the Arrow button (K/ L/s/ B) to
select an item and the ENTER button to
confirm selection.
CALLING UP A MENU SCREEN
DURING PLAYBACK
¡Press the DISC MENU button to call up the DVD menu.
¡Press the TITLE button to call up the title menu.
NOTE:
¡Contents of menus and corresponding menu operations may vary between discs. Refer to the manual
accompanying the disc for details.
– 37 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 38
FAST FORWARD/REVERSE
SEARCH
RESUME
DVD-V
CD
MP3
DVD-V
1 During playback, press the STOP button.
¡Resume message will appear on the TV screen.
button h or g for a few seconds.
¡“ g 1” or “h 1” appears on the screen.
from the point at which playback was stopped.
¡To cancel resume, press the STOP button twice.
¡If the unit is turned off, resume function will be can-
celled.
¡For MP3, playback will resume from the beginning
of the track at which playback was stopped.
PAUSE
CD
MP3
1 During playback, press and hold the SEARCH
2 Press the PLAY button, playback will resume
DVD-V
CD
2 To select another speed, repeat step [1] until
your required speed appears on the screen.
¡For DVDs, fast forward/reverse search speed is dif-
ferent depending on the disc. Approximate speed is
1 (×2), 2 (×8), 3 (×50) and 4 (×100).
¡For audio CDs, approximate speed is ×16.
¡For MP3, approximate speed is ×8.
¡When you use buttons on the front panel, use the
SKIP G/ SEARCH g or SKIP H/ SEARCH
h button.
MP3
3 To return to normal playback, press the
1 During playback, press the PAUSE button.
PLAY button.
¡Playback will pause and sound will be muted.
2 To continue playback, press the PLAY button.
SLOW FORWARD /
SLOW REVERSE
STEP BY STEP PLAYBACK
DVD-V
DVD-V
1 During playback, press the PAUSE button.
1 During playback, press the PAUSE button.
2 Press and hold the SEARCH button h or
¡Playback will pause and sound will be muted.
2 The disc goes forward by one frame each
¡“
3 To select another speed, repeat step [2] until
time the PAUSE button is pressed.
3 To exit step by step playback, press the
PLAY button.
g for a few seconds.
1” or “
1” appears on the screen.
your required speed appears on the screen.
¡Slow forward or reverse speed varies with the disc.
Approximate speed is 1 (1/16), 2 (1/8) and 3 (1/2).
¡When you use buttons on the front panel, use the
SKIP G / SEARCH g or SKIP H / SEARCH
h button.
4 To return to normal playback, press the
PLAY button.
– 38 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 39
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
MP3
DVD-V
CD
There are three ways to begin playback on an Audio
CD and MP3 at a specific track.
1 During playback press the SEARCH MODE
Using the Number buttons on the remote control
2 Within 30 seconds, enter a desired disc
button three times (CD: twice) to display the
Time Search on the TV screen.
1 Press the Number buttons to enter the
time using the Number buttons on the
remote control.
desired Track number.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡Playback will start at the specified time.
¡Press the CLEAR button to erase the incorrect input.
¡When there is no need to enter a number, “0”
appears automatically. For example, “ 0 : 0 - : - -”
appears in the Time Search display if the total time
of the track or title is less than 10 minutes.
¡To play track 26, press +10, 2, 6.
Using the SEARCH MODE button
1 Press the SEARCH MODE button.
MARKER SETUP SCREEN
¡The track search display appears.
DVD-V
2 Within 30 seconds, select a desired track
number using the Number buttons on the
remote control.
CD
Use markers to memorize your favorite places on a disc.
¡For single digits press 0 first, if the total track of the
disc is more than 10.
¡Playback will start at the selected track.
1 Press the SEARCH MODE button four times
(CD: three times) during playback.
¡The display screen and Markers will appear on the
Using the SKIP H G buttons
During playback, press the SKIP G button to move
the next track. Press it repeatedly to skip subsequent
tracks. Press the SKIP H button to go back to beginning of the current track. Press it repeatedly to go to
the previous tracks.
¡If the SKIP button is pressed while the playback is
paused, the playback will be paused again after skipping to the next track.
NOTE:
¡The SKIP H G buttons are not available when
playback is stopped.
TV screen.
2 Press the Arrow button (s/ B) to select 1, 2,
3, 4, 5, 6, 7, 8, 9 or 10 and ensure that “- - - : - - : - -” appears in the display.
3 When you reach the desired point press the
ENTER button.
¡The Title or Track and elapsed playing time will
appear in the TV screen.
4 To return to the Marker later, press the
SEARCH MODE button four times (CD: three
times) during playback and the Arrow button (s/ B) to choose the desired marker
then press the ENTER button.
TITLE / CHAPTER SEARCH
DVD-V
1 Press the SEARCH MODE button once for
the Chapter search, twice for the Title
search during playback.
_ /2
2 Enter the desired chapter/title number using
NOTES:
¡Opening the disc tray, turning off the power, pressing the SELECT button or selecting AC at step [2]
and press the ENTER button will erase all Markers.
¡To clear a marker using the Arrow button s or B,
position the cursor on to the marker number to be
cleared and press the CLEAR button.
¡You can mark up to 10 points.
the Number buttons on the remote control.
¡Playback will start at the selected chapter or title.
¡Press the CLEAR button to erase the incorrect input.
¡For single digits press 0 first, if the total chapter or
5 Press the SEARCH MODE or RETURN button to exit.
title of the disc is more than 10.
– 39 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 40
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
REPEAT is available only during playback.
CD
REPEAT TITLE / CHAPTER
DVD-V
To activate the repeat function press the
REPEAT button during playback.
You may determine the order in which tracks will play.
1 In stop mode, press the MODE button.
¡The repeat mode changes as described below every
¡The PROGRAM screen will appear.
2 Press the Arrow button (K/L) to select a
time you press the button.
CHAPTER
TITLE
(current chapter repeat) (current title repeat)
OFF
(repeat off)
track, then press the
ENTER button.
erase the most recently entered
program.
NOTES:
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
3 Repeat step [2] until you have selected all
the tracks you want to play in the program.
4 Press the PLAY button to play the programmed tracks.
REPEAT TRACK/ALL
CD
To activate the repeat function press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
TRACK
(current track repeat)
TOTAL
¡Press the CLEAR button to
ALL
(entire disc repeat)
OFF
(repeat off)
NOTES:
¡Repeat setting will be cleared when moving to other
track.
¡Repeat playback does not function during repeat A-B
playback.
NOTES:
¡While the program is being played back, the STOP
works as follows.
¡Press the STOP button once and then the PLAY button again, playback will restart from the point where
the STOP button was pressed. (Program continued)
¡Press the STOP button twice and then the PLAY
button again, playback will restart from the track in
the usual way. (Program canceled)
¡Up to 99 programs can be entered.
¡To erase all tracks in the program at once, select
ALL CLEAR at the bottom of the list at Step [2].
¡If you like to repeat the current track in the program,
press the REPEAT button repeatedly until “ TRACK”
appears during playback. If you like to repeat the entire
program press the REPEAT button repeatedly until
“ ALL” appears during playback.
REPEAT A-B
DVD-V
RANDOM PLAYBACK
CD
CD
1 Press the REPEAT A-B button at your chosen starting point.
¡“
This shuffles the playing order of tracks instead of
playback in the sequence.
A-” appears briefly on the TV screen.
2 Press the REPEAT A-B button again at your
chosen end point.
1 In stop mode, press the MODE button twice.
¡RANDOM screen appears.
RANDOM
CD-DA
¡“
A-B” appears briefly on the TV screen and the
repeat sequence begins.
TOTAL 0:45:55
RANDOM PROGRAM
- - no indication - -
3 To exit the sequence, press the REPEAT
PLAY
A-B button.
NOTES:
¡The repeat A-B section can only be set within the current title (for DVDs) or current track (for Audio CDs).
¡Repeat A-B is not available with some scenes in DVD.
¡To cancel the A point which was set, press the
CLEAR button.
¡Repeat A-B playback does not function during title,
chapter, track or all repeat playback.
2 Press the PLAY button to start random playback.
NOTE:
¡If you like to repeat the current track in the random
selection, press the REPEAT button repeatedly until
“
TRACK” appears during playback. If you like
to repeat the entire random selection press the
REPEAT button repeatedly until “ ALL” appears
during playback.
– 40 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 41
PLAYING A MP3 DISC
MP3 PLAYBACK
PROGRAM
MP3
MP3
When a CD with MP3 files is in the unit, press the
DISC MENU button to call up the MP3 menu on the
TV screen.
1 In stop mode, press the Arrow button (K/L)
This feature allows you to program an MP3 disc to
play in a desired sequence.
1 In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
to select the desired group or track.
¡If a group is selected press the
Arrow B or ENTER button to
go on to the track selection
screen. Press the Arrow button (K/L) to choose a track,
then press the ENTER button.
¡If a track is selected, press the
ENTER button to start playing tracks. Starting from
the one you’ve just chosen the subsequent tracks
will be played.
¡Press the TITLE button to return to the first item.
folder name 1
folder name 2
folder name 3
folder name 4
file name 1
file name 2
file name 3
folder name 1
2 Select a desired track using the Arrow button (K/L/s/B). Then press the ENTER
button.
¡Press the Arrow button B when you want to go to
the next hierarchy.
¡Press the Arrow button s when you want to go back
to the previous hierarchy.
¡Press the CLEAR button to erase the most recently
entered program.
3 Repeat step [2] until you have selected all
the Tracks you want to play in the program.
2 Press the STOP button to stop playback.
NOTES:
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by 3 icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 512 files can be recognized.
¡Up to 8 hierarchies can be created.
This unit recommends the use of files recorded at the
below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
4 Press the PLAY button to start programmed
playback.
NOTES:
¡While the program is being played back, the STOP
button works as follows.
¡Press the STOP button once and then the PLAY
button again, playback will restart from the beginning of the track. (Program continued)
¡Press the STOP button twice and then the PLAY
button again, playback will restart from the track in
the usual way. (Program canceled)
¡To erase all tracks in the program at once, select
ALL CLEAR at the bottom of the list at Step [2].
REPEAT
RANDOM PLAYBACK
MP3
MP3
REPEAT is available only during playback.
1 In stop mode, press the MODE button twice.
To activate the repeat function, press the
REPEAT button during playback.
¡RANDOM screen appears.
¡The repeat mode changes as described below every
2 Press the PLAY button to start random play-
time you press the button.
back.
TRACK
(current track
repeat)
GROUP
(current group
repeat)
ALL
(entire disc
repeat)
OFF
(repeat off)
NOTE:
¡Repeat setting will be cleared when moving to other
track.
– 41 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 42
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
CAMERA ANGLE
DVD-V
DVD-V
The unit allows you to select a language for subtitles
during DVD disc (if available) playback.
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change the
camera angle when the (
) icon appears on the screen.
1 Press the SUBTITLE button during playback.
2 Press the SUBTITLE button repeatedly to
1 Press the ANGLE button during playback.
select your desired subtitle language.
¡The selected angle will be displayed on the display
¡The subtitle language will appear on the display bar
at the top of the TV screen.
bar at the top of the screen.
2 Press the ANGLE button repeatedly to
3 To turn off subtitles, press the SUBTITLE
select your desired angle.
button repeatedly until “OFF” appears.
NOTES:
¡Some discs allow audio language setting/subtitle language
setting on the disc menu. (Operation varies between discs,
so refer to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 44.)
BLACK LEVEL SETTING
DVD-V
Adjust the Black Level Settings to make the black
parts of the picture brighter.
1 Press the MODE button during playback.
OFF
2 Press the ENTER button to switch OFF.
AUDIO LANGUAGE
DVD-V
The unit allows you to select a language during DVD
disc (if multi languages are available) playback.
1 Press the AUDIO button during playback.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
3 Press the MODE button twice or the
RETURN button to exit.
NOTE:
¡The setting will be saved even if the unit is turned off.
2 Press the AUDIO button repeatedly to select
VIRTUAL SURROUND
your desired language.
NOTE:
¡Pressing the AUDIO button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc menu).
DVD-V
CD
MP3
You can enjoy surround-sound effect over two speakers on this unit.
1 Press the V.SURR button once or the MODE
STEREO SOUND MODE
CD
button twice (CD/MP3: once) during playback.
OFF
1 Press the AUDIO button repeatedly during
playback to select between STEREO, L-CH
or R-CH.
¡STEREO - both right and left channels are active (stereo)
2 Press the ENTER button to set it 1 (Natural
effect) or 2 (Emphasized effect) or OFF.
3 Press the V. SURR or RETURN button to exit.
L-CH - only left channel is active
R-CH - only right channel is active
NOTE (for CD play only):
NOTE:
¡Virtual Surround will not be effective if the sound
¡If the Virtual Surround setting is ON, the sound mode
mode is set to something other than STEREO.
will be fixed to STEREO and can not be changed.
EN
– 42 –
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 43
THE ON-SCREEN INFORMATION
DVD-V
CD
MP3
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
For DVD-Vs
For Audio CDs
1 Press the DISPLAY button during playback
1 Press the DISPLAY button during playback
to show current Chapter.
to show the current Track.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
¡The elapsed and remaining playing time of the cur9/49
rent track will be displayed.
0:00:00 -0:03:30
2 Press the DISPLAY button again to show
2 Press the DISPLAY button again to show
current Total Track.
current Title.
¡The elapsed and remaining playing time of the total
track will be displayed.
¡The elapsed and remaining playing time of the cur-
rent title will be displayed.
3 Press the DISPLAY button again to exit the
display.
3 Press the DISPLAY button again.
¡The BIT RATE and the current repeat setting will be
For MP3
displayed.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
1 Press the DISPLAY button during playback.
¡The name of the file currently in play will be dis-
played.
4 Press the DISPLAY button again to exit the
2 Press the DISPLAY button again to show
display.
the track number, the elapsed time, the
repeat status and the playback status at the
top of the screen.
¡
will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3 Press the DISPLAY button again to exit the
display.
– 43 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 44
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
DVD-V
Language options are not available with some discs.
1 Press the SETUP button twice in STOP
mode so that the DVD SETUP menu
appears.
¡ If the menu does not appear, press the PLAY button
and the STOP button then the SETUP button twice.
SETUP
QUICK
CUSTOM
INITIALIZE
2 Press the Arrow button L to select CUSTOM, then press the ENTER button.
¡CUSTOM mode will appear.
3 Press the Arrow button (K/L) to select
“LANGUAGE”, then press the ENTER button
to confirm.
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
4 Press the Arrow button (K/L) to select the
next items, then press the ENTER button.
AUDIO: Sets the audio language.
SUBTITLE: Sets the subtitle language.
DISC MENU: Sets the language for DVD menu.
5 Press the Arrow button (K/L) to select a
setting, then press the ENTER button.
¡If OTHER is selected on the AUDIO, SUBTITLE
or DISC MENU screen, press four-digit number to
enter the code for the desired language (Refer to
the language code list).
¡Only the languages supported by the disc can be
selected.
6 Press the SETUP button to exit.
NOTE:
¡Language Setting for Audio and Subtitle is not available with some discs. Then use the AUDIO and the
SUBTITLE buttons (Details are on page 42).
Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
TO CHANGE THE ON-SCREEN MENUS
You can access the TV/VCR SETUP menu by pressing the SETUP button from the DVD mode. Refer to
SELECTING THE LANGUAGE on page 15 for
changing the on-screen menus.
Code Language
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
If you choose a Language that has a 3 letter language
code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 42. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
– 44 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 45
DISPLAY SETTING
AUDIO SETTINGS
DVD-V
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
MP3
Choose the appropriate Audio settings for your equipment as it only affects during the playback of DVD
discs.
1 Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button
1 Press the SETUP button twice in STOP mode
and the STOP button then the SETUP button twice.
¡ If the menu does not appear, press the PLAY button,
so that the DVD SETUP menu appears.
the STOP button, then the SETUP button twice.
SETUP
SETUP
QUICK
CUSTOM
INITIALIZE
QUICK
CUSTOM
INITIALIZE
2 Press the Arrow button L to select “CUSTOM”, then press the ENTER button.
¡CUSTOM mode will appear.
2 Press the Arrow button L to select “CUSTOM”, then press the ENTER button.
3 Press the Arrow button (K/ L) to select “DIS-
¡CUSTOM mode will appear.
PLAY”, then press the ENTER button to confirm.
SETUP
3 Press the Arrow button (K/ L) to select
CUSTOM
“AUDIO”, then press the ENTER button to
confirm.
LANGUAGE
DISPLAY
AUDIO
PARENTAL
SETUP
4 Press the Arrow button (K/ L) to select the
below items, then press the ENTER button.
TV MODE: QUICK
¡Press the Arrow button (K/L) for an item selection,
then press the ENTER button.
¡Select 4:3 LETTER BOX for black bars to appear on
top and bottom of the screen.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
¡The default setting is 4:3 LETTER BOX.
STILL MODE:
¡Press the Arrow button (K/L) for an item selection,
then press the ENTER button.
¡Select “AUTO” usually.
¡If you select “FIELD”, the picture in the still mode
will be stabilized.
¡If you select “FRAME”, the picture in the still mode
will be highly defined.
ANGLE ICON:
¡Press the ENTER button repeatedly to turn Angle
icon ON or OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press the ENTER button repeatedly to turn Auto
Power off ON or OFF.
¡The default setting is ON and the screen saver program starts when there is no input signal to the unit
for 5 minutes in the stop mode. When the screen
saver program is activated for 15 minutes, the power
automatically turns off.
5 Press the SETUP button to exit.
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
4 Press the Arrow button (K/ L) to select the
below items, then press the ENTER buttons.
DRC (Dynamic Range Control):
¡To compress the range of soft to loud sound.
¡The default setting is ON.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.
DOLBY DIGITAL: QUICK
Set to On when the unit is connected to a Dolby Digital
Decoder.
ON: Output a Dolby Digital signal
OFF: Convert the Dolby Digital to PCM (2 channel
stereo)
¡The default setting is ON.
– 45 –
5 Press the SETUP button to exit.
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 46
CONTROL LEVELS
PARENTAL CONTROL
¡ALL
DVD-V
All parental lock is cancelled.
¡Level 8
DVD software of any grade (adult/general/children)
can be played back.
Parental Control limits the disc viewing that exceed
your settings (with a password or playback will stop).
This feature allows you to prevent discs with alternative scenes from being played by your children.
¡Levels 7 to 2
PARENTAL LEVEL
¡Level 1
Only DVD software intended for general use and
children can be played back.
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.
Only DVD software intended for children can be
played back, with those intended for adult and
general use is prohibited.
1 Press the SETUP button twice in STOP mode
so that the QUICK SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
IF YOU FORGET THE PASSWORD
the STOP button, then the SETUP button twice.
1 Press the number buttons 4, 7, 3, 7 at step
[4], then enter your new password.
¡Password will be cleared and parental level will be
2 Press the Arrow button L to select “CUSTOM”, then press the ENTER button.
set to ALL.
SETUP
2 Proceed the Steps [5] to [7] again.
QUICK
CUSTOM
INITIALIZE
3 Press the Arrow button (K/ L) to select
INITIALIZE
“PARENTAL”, then press the ENTER button.
SETUP
This allows you to return all selections of SETUP
(except for PARENTAL) to their default settings.
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
1 Press the SETUP button twice in STOP
mode so that the INITIALIZE menu appears.
4 Enter your four-digit password then press
2 Press the Arrow button (K/ L) to select “INI-
the ENTER button.
TIALIZE”, then press the ENTER button.
5 Press the Arrow button (K/ L) to select
3 Select “YES”, then press the ENTER button
“PARENTAL LEVEL”, then press the ENTER
button.
6 Press the Arrow button (K/ L) to select the
desired level, then press the ENTER button.
twice. All the settings (except for
“PARENTAL”) will be cleared.
¡To cancel the initialization, select “NO”.
4 Press the SETUP button to exit.
7 Press the SETUP button to exit
NOTES:
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password.(in the event you forget the password, see
below)
¡To change the password, press the Arrow button (K
/ L) to select CHANGE at step [5], then press the
ENTER button. Enter the four-digit password, then
press the ENTER button.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way
that you have set.
¡Record the password in case you forget it.
– 46 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 47
TROUBLESHOOTING GUIDE
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, consulting the following checklist.
PROBLEM
No power
The unit does not respond to
the remote control
CORRECTIVE ACTION
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote.
• You have to be within 23 feet of the unit.
• Check if the correct mode is selected. If not switch the mode by
pressing the SELECT button on the remote control,whichever you need.
TV/VCR Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
CORRECTIVE ACTION
No picture and sound
Make
sure
the
AC
cord
is connected to an AC outlet.
•
• Check antenna connection.
• Press the SELECT button on the remote control to select TV mode.
Then try other TV feature.
• Let the unit program its tuner memory.
No picture or poor picture on
• Adjust direction or replace antenna.
the unit
• Adjust picture controls.
No sound or poor sound
• Adjust volume control on remote control or main unit.
• Press the MUTE button to restore sound.
Bars On Screen
• If outside antenna is being used, check for broken wire.
• Check for local interference.
Picture Distorted or Blurred
• Try a new channel, if OK, then possible station trouble.
• If outside antenna is being used, check for broken wire.
Picture Rolls Vertically
• Try a new channel, if OK, then possible station trouble.
Lines or Streaks in Picture
• If outside antenna is being used, check for broken wire.
• Check for local interference.
No Color
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust COLOR control.
Poor Reception on Some Channels • Try a new channel, if OK, then possible station trouble.
Ghosts in Picture
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
Weak Picture
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust CONTRAST & BRIGHT control.
Sound OK, Picture Poor
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Adjust CONTRAST & BRIGHT control.
– 47 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
PROBLEM
Picture OK, Sound Poor
Timer recording is not possible
Cannot go into Record mode
Playback picture is partially noisy
No picture but the audio is OK in
playback
No operation by infrared Remote
Control
Video or color fades in and out
when making a copy of a video tape
Different color marks on screen
Page 48
CORRECTIVE ACTION
• Try a new channel, if OK, then possible station trouble.
• Check for local interference.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the clock of the unit is set correctly.
• Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
• Adjust tracking control for a better picture using the CHANNEL
• button K or L on the unit.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 50.
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
• Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the unit away from the appliances,
the unit can repair itself automatically. If you want to repair immediately, unplug the power cord, then plug it in again 30 minutes later
or so. This automatically resets the unit.
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
My unit is showing captions that
• You are watching a live broadcast and spelling errors made by the
are misspelled.
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My unit will not show the text
• Captions that are delayed a few seconds behind the actual
dialogue in its entirety or there is
are common for live broadcast. Most captioning production
a delay of what is being said.
• companies can display a dialogue to a maximum of 220 words
• per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with
• Interference caused by building, power lines, thunderstorms, etc.
white boxes on the TV screen.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box
• company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
• You are in the TEXT mode. Select CAPTION mode to CAPTION
on certain channels.
• [OFF].
– 48 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 49
DVD Mode
PROBLEM
CORRECTIVE ACTION
• Insert a correct video disc that plays on this unit.
• Press the SELECT button on the remote control to select DVD mode.
Then, try other DVD feature.
•
Insert the disc.
Disc cannot be played
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This unit does not support DTS audio. This is not a malfunction.
No DTS audio is output
• There are some cases where pictures may be slightly distorted, which
Distorted picture
are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
• The selected language is not available for audio or subtitles on the DVD.
does not match the set up
This is not a malfunction.
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera
angles. This is not a malfunction.
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected
changed
language. This is not a malfunction.
“Prohibited icon” appears on the
• That operation is prohibited by the unit or the disc.
screen, prohibiting an operation
This is not a malfunction.
CD sound dropout
• Scratched disc. Replace the disc with an unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
No picture
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
– 49 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 50
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
•
the unit with a soft cloth immersed in lukewarm
water and wrung dry.
Never use a solvent or alcohol. Do not spray insecticide liquid near the unit. Such chemicals may
cause damage and discoloration to the exposed surfaces.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-256-2487, to
locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
AUTO HEAD CLEANING
SERVICING
• Automatically cleans video heads as you insert or
•
remove a cassette, so you can see a clearer picture.
Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your unit may need to be
cleaned.
• Should your unit become inoperative, do not try to
correct the problem by yourself. There are no userserviceable parts inside. Turn off, unplug the power
cord and please call our help line at 1-800-2562487, to locate an Authorized Service Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
• If the unit still does not perform properly when it is operated, while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Use discs which have the following logos on them.
(Optical audio digital discs.)
Recordable
ReWritable
• To clean-off, use a soft cloth.
• Do not use a hard cloth since this will mar the disc.
• Wipe the disc in a straight line from center to edge.
• Never wipe with a circular motion.
• Do not use detergent or abrasive cleaning agents.
• Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it
is not used.
– 50 –
EN
01A11
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 51
SPECIFICATIONS
GENERAL SPECIFICATIONS
TV/VCR
CRT
19 inch in-line gun,
90˚ deflection tube
Television system :
NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Rotary four-head
Tape width :
1/2 inch
Tape speed
SP :
33.40mm/sec.
LP :
16.67mm/sec.
SLP :
11.12mm/sec.
Tuner channel
TV VHF Low :
#2~#6
TV VHF High :
#7~#13
TV UHF :
#14~#69
CATV
VHF :
5A
MID band :
A5~A1, A~I
SUPER band :
J~W
HYPER band :
W+1~W+84
DVD
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input:
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output:
Remote control:
Operating
temperature:
Power requirements:
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
1/8” stereo (3.5 mm)
One pin jack,
500m Vpp (75 ohm)
Digital encoded
infrared light system
5˚C to 40˚C
(41˚F~104˚F)
AC 120V, 60Hz
90W
19"
H:19-11/16” (500mm)
W:21-7/8” (556mm)
D:18-3/4” (476.5mm)
45.2 lbs (20.5kg)
Product type:
DVD Player
Discs:
DVD video, Audio CD
Output signal format: NTSC color
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will be English.
– 51 –
EN
01A11
T0052UC(ES).QX3
04.9.16
2:18 PM
Page 52
INDICE
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52
PANEL FRONTAL DEL UNIDAD . . . . . . . . . . . . . . . . . 52
MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 52
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54
MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
EQUIPADO CON TOMAS DE ENTRADA DIGITAL,
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SECCIÓN DE TV/VCR
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 54
AJUSTE DE CANALES . . . . . . . . . . . . . . . . . . . . . . . . . 55
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
CONTROLES DE
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL UNIDAD
Consulte la figura 1 de la página 9
MANDO A DISTANCIA
Consulte la figura 2 de la página 9
VISTA POSTERIOR
Consulte la figura 3 de la página 10
1. Botón POWER
Presione este botón para conectar y desconectar la alimentación.
2. Botones VOLUME (VOL.) X/Y
Presione estos botones para controlar el nivel de volumen del DVD y el televisor.
3. Botones SKIP/SEARCH (para DVD)
Presione el botón correspondiente una vez para omitir
capítulos o pistas y desplazarse a un punto específico.
Mantenga el botón presionado para cambiar la velocidad de reproducción en avance o retroceso.
4. Botón PLAY
Inicia la reproducción del contenido del disco o cinta.
5. Botón STOP
Detiene la reproducción del disco.
6. Botón OPEN/CLOSE
Presione este botón para insertar discos en la bandeja o
retirarlos de ella.
7. Bandeja de carga del disco
8. Indicador DVD
Se ilumina durante el modo DVD.
9. Botón SELECT
Presione este botón para cambiar al modo TV/VCR,
modo de entrada externa o modo de DVD.
10. Indicador TV/VCR
Se ilumina durante el modo TV/VCR.
11. Botones CHANNEL (CH.) K/L
Utilice estos botones para seleccionar canales memorizados.
12. Indicador de grabación
Parpadea durante la grabación. Se ilumina durante el
modo de espera de grabación controlada por temporizador.
13. Botón REC/OTR (Panel frontal)
Presione para empezar la grabación manual. Presione
repetidamente para empezar la grabación instantánea
(OTR).
Botón RECORD (Mando a distancia)
Presione para empezar la grabación manual.
14. Botón REW (para TV/VCR)
Presione este botón para rebobinar la cinta o para ver
la imagen rápidamente en dirección de retroceso
durante el modo de reproducción. (Búsqueda en dirección de retroceso)
15. Botón F.FWD (para TV/VCR)
Presione este botón para adelantar rápidamente la cinta
o para ver la imagen rápidamente en dirección de
avance durante el modo de reproducción. (Búsqueda en
dirección de avance)
16. Botón STOP/EJECT
Presione este botón para detener la cinta. Presiónelo en
el modo de parada para retirar la cinta del unidad.
17. Ventanilla del sensor de mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar
en privado.
19. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
21. Compartimiento del cassette
22. Botón PICTURE
Presione este botón para ajustar la imagen.
23. Botones numéricos
Modo TV/VCR:
Presione dos botones para acceder directamente al
canal deseado.
No olvide presionar “0” antes de elegir un canal de un
solo dígito.
Botón +100
Presione este botón para seleccionar canales de televisión por cable cuyo número sea igual o superior a 100.
Modo DVD:
Presione este botón para introducir el número deseado.
Botón +10
Presione este botón para introducir números iguales o
mayores que 10.
24. Botón PAUSE
Hace una pausa en la reproducción del disco o cinta.
25. Botón SPEED
Presione este botón para seleccionar la velocidad de
grabación deseada: SP/SLP.
26. Botón C.RESET
Presione este botón para poner el contador en 0:00:00.
Presiónelo también para cancelar un ajuste de programa de temporizador.
27. Botón DISPLAY
Modo TV/VCR:
Para visualizar el contador o el número del canal y la
fecha actual en la pantalla del televisor.
Modo DVD:
Indica el estado actual en la pantalla del televisor para
fines de comprobación.
28. Botón SETUP
Presione este botón para activar o salir del modo de
menús de televisor o configuración de DVD.
– 52 –
ES
0C28
T0052UC(ES).QX3
04.9.16
2:18 PM
Page 53
29. Botón TITLE
Para visualizar el menú de títulos.
30. Botón CLEAR
Para cancelar ajustes.
31. Botón MODE
Activa el modo de reproducción programada o el modo
de reproducción aleatoria.
32. Botón SEARCH MODE
Presione este botón para localizar un punto deseado.
33. Botón AUDIO
Presione este botón para seleccionar un idioma de
audio o el modo de sonido deseado.
34. Botón SUBTITLE
Presione este botón para seleccionar el idioma de subtítulos deseado.
35. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
36. Botón ANGLE (modo DVD)
Presione este botón para cambiar el ángulo de la cámara
y ver la secuencia que se está reproduciendo desde un
ángulo diferente.
37. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
38. Botón RETURN
Permite volver a la operación anterior en el modo de
configuración de DVD.
39. Botón ENTER
Presione este botón para establecer un ajuste.
40. Botones de flechas
Modo TV/VCR:
Presione estos botones para seleccionar un modo de
ajuste en el menú que aparece en la pantalla del televisor.
Presiónelos también para seleccionar opciones o
establecer ajustes en un menú en particular.
Modo DVD:
Use estos botones para hacer ajustes mientras observa
la imagen en la pantalla del televisor.
41. Botón DISC MENU
Muestra los menús contenidos en el DVD.
42. Botón V.SURR
Activar/desactivar el envolvente virtal.
43. Botón MUTE
Suprime la salida de sonido. Presiónelo de nuevo para
restablecer el sonido.
44. Botón SLEEP
Utilice este botón para ajustar el temporizador de dormir.
45. Botón SELECT
Presione este botón para cambiar entre los modos
TV/VCR y DVD. El modo seleccionado (TV/VCR o
DVD) se visualiza en el indicador del panel delantero.
46. Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por cable
o sistema de satélite.
47. Cable de alimentación
Conéctelo a una toma de CA estándar (120V/60Hz).
NOTA: Antes de conectar el cable de alimentación a
una toma de CA estándar, retírelo del gancho
para evitar dañarlo.
48. Toma de salida de audio digital COAXIAL
Conéctela solamente a la entrada digital de un amplificador externo o decodificador de audio de DVD.
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena
exterior.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su unidad, sin una
caja de convertidor.
Con esta conexión podrá:
1) Utilizar el mando a distancia del unidad para seleccionar canales.
2) Programar uno o más canales decodificados para
grabación automática controlada por temporizador.
NOTA: Este unidad SÓLO puede grabar el canal que
se está viendo.
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su compañía de televisión por cable le suministra
una caja de convertidor o si utiliza un sistema de
satélite, podrá utilizar la conexión básica que se
muestra en la ilustración.
Al utilizar esta conexión, también podrá grabar canales
codificados. Sin embargo, la selección de los canales
deberá hacerse con la caja de convertidor o con la caja
de satélite. Esto significa que no es posible cambiar de
canal utilizando el mando a distancia del unidad. La
grabación en ausencia (controlada por temporizador)
está limitada a un canal a la vez.
PARA GRABAR UN CANAL
CODIFICADO/DECODIFICADO
1.Ajuste el selector de canales del unidad al canal de
salida de la caja de convertidor de televisión por
cable o caja de satélite. (Ej., CH3)
2.Seleccione el canal que desea grabar en la caja de
convertidor de televisión por cable o caja de satélite.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en particular, especifica
que la tierra del cable debe conectarse al sistema
de puesta a tierra del edificio, tan cerca del punto
de entrada del cable como sea posible.
CONEXIÓN A TOMAS DE ENTRADA
EXTERNA
CONEXIONES DE ANTENA/CABLE
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada de audio/vídeo de la parte delantera del unidad.
Conecte las tomas de salida de audio/vídeo de otra
fuente a las tomas AUDIO L/R y VIDEO de este
unidad. Luego, presione los botón CHANNEL K o L
hasta que aparezca "AUX" en la pantalla.
NOTA:
• Cuando conecte una videograbadora monofónica
(otra fuente) a este televisor/videograbadora/DVD,
conecte la toma de salida de audio de la
videograbadora monofónica (otra fuente) a la toma
AUDIO L de este unidad. El audio saldrá igualmente por los canales izquierdo y derecho.
Consulte la figura 4 de la página 11
Consulte la figura 5 de la página 12
PREPARACIÓN PARA LA
UTILIZACIÓN
– 53 –
ES
0C28
T0052UC(ES).QX3
04.9.16
2:18 PM
Page 54
PARA INSERTAR LAS PILAS
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a
distancia en el sentido de la flecha.
2) Inserte 2 pilas "AA" en el
compartimiento de las pilas, en el
sentido indicado por las marcas de polaridad (+/-).
3) Vuelva a poner la cubierta.
MODO DE ENTRADA EXTERNA
Al usar una señal de entrada externa (otra videograbadora o una videocámara), conecte los cables de salida
de audio/vídeo del equipo externo a las tomas
AUDIO L/R IN/ VIDEO IN de su unidad, luego presione los botón CHANNEL K o L hasta que aparezca "AUX" en la pantalla.
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS DE
ENTRADA DIGITAL, PLATINA MD O
PLATINA DAT (Para DVD)
Utilice un cable digital coaxial de audio de venta en el
comercio especializado para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
Utilice cables digitales coaxiales de audio
disponibles en el comercio especializado para hacer
las conexiones de audio.
Consulte la figura 7 de la página 14
NOTAS:
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
• Consulte los manuales de instrucciones de los
componentes que va a conectar al unidad.
• Si conecta un decodificador Dolby Digital, ajuste
la función DOLBY DIGITAL a ON para salida de
audio en el modo de configuración.
• A menos que se haga la conexión a un decodificador Dolby Digital, ajuste la función Dolby
Digital a OFF para salida de audio en el modo de
configuración. La reproducción en un unidad utilizando ajustes incorrectos puede generar ruido y
distorsión, y también puede causar daños a los
altavoces.
Fabricado bajo licencia de Dolby Laboratories.
“Dolby” y el símbolo de la D doble son marcas
de fábrica de Dolby Laboratories.
SECCIÓN DE TV/VCR
Consulte la figura 6 de la página 13
NOTAS:
• La fuente de audio de un disco grabado en formato
de sonido envolvente Dolby Digital de 5,1 canales
no se puede grabar como sonido digital mediante
una platina MD o DAT.
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
• Consulte los manuales de instrucciones de los
componentes que va a conectar al unidad.
• Ajuste la función Dolby Digital a OFF para salida
de audio en el modo de configuración. La reproducción en un unidad utilizando ajustes incorrectos
puede generar ruido y distorsión, y también puede
causar daños a los altavoces.
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
PREPARACIÓN PARA LA
UTILIZACIÓN
SELECCIÓN DE IDIOMA
TV/VCR
1
2
Si utiliza este unidad para reproducir un disco DVD
grabado en formato de sonido envolvente Dolby
Digital de 5,1 canales, el unidad emitirá un flujo de
datos DOLBY DIGITAL desde su toma de salida de
audio digital COAXIAL. Si conecta el reproductor a
un decodificador Dolby Digital, podrá disfrutar de
una tonalidad más convincente y real, con un sonido
envolvente potente y de alta calidad similar al de los
cines.
Enchufe el cordón de alimentación del unidad
Enchufe el cordón de alimentación del unidad en una
toma de CA estándar.
NOTA:
• Si aparecen algunas cifras en la esquina de la pantalla, pulse el botón POWER sin desenchufar el
cordón de alimentación.
Asegúrese de que ...
• Pulse el botón POWER para encender el unidad.
NOTA: Esta función afecta sólo el idioma en el menú
de la pantalla y no la fuente de audio.
Seleccione “LANGUAGE”
Pulse el botón SETUP en el mando a distancia.
Pulse el botón K o L para señalar “LANGUAGE”.
3
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”
con el botón ENTER.
4
Salga del modo de idioma
Pulse el botón SETUP en el mando a distancia para
volver al modo del televisor.
– 54 –
ES
0C28
T0052UC(ES).QX3
04.9.16
2:18 PM
Page 55
NOTA: Si, por alguna razón, el menú está en español
o francés, pulse el botón SETUP en el mando a distancia, pulse el botón K para señalar el “LANGUAGE
[ENGLISH]” o “LANGAGE [FRANÇAIS]”, a continuación, pulse el botón ENTER y pulse el botón
SETUP en el mando a distancia.
TV/VCR
Puede programar el sintonizador para buscar todos
los canales que recibe en su localidad.
NOTA: El canal preparado NO es necesario cuando
esté conectado a una caja de cable o caja de satélite.
Sólo tiene que seleccionar con el selector de canal
del unidad al canal de salida de la caja de cabe o caja
de satélite (por ejemplo el canal CH3). Seleccione el
canal a ver en la caja de cable o caja de satélite.
4) Pulse el botón K o L hasta que aparezca el día
del mes deseado (Ejemplo: 6 - 06), luego pulse el
botón B.
5) Pulse el botón K o L hasta que aparezca el año
deseado (Ejemplo: 2004), luego pulse el botón B.
6) Pulse el botón K o L hasta que aparezca la hora
deseada (Ejemplo: 5, PM), luego pulse el botón B.
7) Pulse el botón K o L hasta que aparezca el minuto deseado (Ejemplo: 40).
8) Pulse el botón SETUP en el mando a distancia.
Aunque los segundos no se visualizan, éstos
empiezan a contar desde 00 cuando se pulsa
MENU en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta.
Asegúrese de que ...
• Pulse el botón POWER para encender el unidad.
Seleccione “AJUSTE DE CANAL”
Pulse el botón SETUP en el mando a distancia.
Pulse el botón K o L para señalar “AJUSTE DE
CANAL”.
A continuación, pulse el botón ENTER.
2
2) Pulse el botón K o L para indicar “AJUSTE
MANUAL RELOJ”, luego pulse el botón ENTER.
3) Pulse el botón K o L hasta que aparezca el mes
deseado (Ejemplo: Mayo - 05), luego pulse el
botón B.
AJUSTE DE CANAL
1
1) Pulse el botón SETUP en el mando a distancia.
Pulse el botón K o L para indicar “AJUSTE
RELOJ”, luego pulse el botón ENTER.
SECCIÓN DE DVD
Empiece el prefijado automático
Pulse el botón K o L para señalar “AUTOPROGRAMACION DE CA.”
A continuación, pulse el botón ENTER.
El sintonizador busca y memoriza todos los canales
activos en su localidad.
3
REPRODUCCIÓN BÁSICA
DVD-V
CD
MP3
Para empezar
Después de buscar
El sintonizador se detiene en el canal memorizado
más bajo.
• Cuando se activa AUTOPROGRAMACION DE
CA, donde no hay entrada de señal del televisor,
aparecerá “NO HAY SEÑAL DE TV” en la pantalla después de terminar la búsqueda de canales.
• El unidad puede reconocer los canales de TV para
que sean canales de TV de antena de cable con las
condiciones de recepción. En este caso, pruebe
nuevamente con el prefijado automático en las
condiciones de recepción fina.
AJUSTE DEL RELOJ
TV/VCR
Cerciórese...
• La alimentación del unidad deberá estar conectada.
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 6 de mayo de 2004
HORA: 5:40 PM
¡Conecte la alimentación del amplificador y otros
componentes, si es necesario.
1 Presione el botón POWER.
¡La alimentación se conectará.
2 Presione el botón OPEN/CLOSE para abrir
la bandeja de carga del disco.
3 Ponga el disco deseado en la bandeja, con
la etiqueta hacia arriba.
4 Presione el botón PLAY.
¡La bandeja se cerrará automáticamente y la repro-
ducción comenzará desde el primer capítulo o pista
del disco. Si la reproducción no comienza automáticamente, presione el botón PLAY.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pantalla.
– 55 –
5 Presione el botón STOP para detener la
reproducción.
ES
0C28
T0052UC(P36-52).QX3
04.9.16
2:12 PM
Page 52
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN
THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest FUNAI Authorized Service Center or for general service procedure, please
call 1-800-256-2487 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-256-2487
http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
1EMN20183
T0052UC ★★★★★