OWNER’S
MANUAL
DVD PLAYER with VIDEO CASSETTE RECORDER
EWD2202
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
EMERSON AND THE G-CLEF LOGO ARE REGISTERED
TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY,
NEW JERSEY, U.S.A.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
TOLL FREE : 1- 800 - 256-2487
Please read before using this equipment.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to
possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO
NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
–2–
EN
1L25
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV
converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. Attachments - Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories - Do not place this video product on
an unstable cart, stand, tripod, bracket, or table.
The video product may fall, causing serious
injury to a child or adult, and serious damage to
the appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the video product. Any mounting of the appliance
should follow the manufacturer's instructions and should use
a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the
video product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the video product on a
bed, sofa, rug, or other similar surface. This video product
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
10. Power Sources - This video product should be operated
only from the type of power source indicated on the marking label. If you are not sure of the type of power supply
to your home, consult your appliance dealer or local power
company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is
equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
14. Lightning - For added protection for this video product
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This
will prevent damage to the video product due to lightning
and power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this video product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in performance this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs
to this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
22. Heat - This video product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
–3–
EN
1L25
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR player. This serial number is
unique to your machine. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SUPPLIED ACCESSORIES
Remote control
A/V cables
Coaxial Cable
(approx. 3 feet (100 cm)
long) (WPZ0102TM015)
WPZ0901TM002
Two AA batteries
(NA202CD)
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
VCR
: refers to playback of video cassette tapes.
DVD
: refers to playback of DVD video discs.
CD
: refers to playback of audio CDs.
MP3
: refers to playback of MP3 discs.
–4–
EN
1L25
TABLE OF CONTENTS
■ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
■ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
■ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
■ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
■ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 9
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 12
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 12
■ VIDEO/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . 13
■ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DVD/VCR TO TV CONNECTION . . . . . . . . . . . . . . . . . . . . 14
SETTING THE CH3/CH4 SWITCH . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT
JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14
CONNECTING TO AN AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT
DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CONNECTING TO A DOLBY DIGITAL DECODER OR
DTS DECODER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CONNECTING TO AN ANALOG AUDIO. . . . . . . . . . . . . . 16
■ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 17
TO CHANGE THE ON-SCREEN LANGUAGE . . . . . . . . . . 18
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
■ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 19
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
■ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 20
VIEWING AND RECORDING THE SAME PROGRAM . . . 20
OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . . . . . . . 20
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 21
■ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 22
MTS (Multi-Channel Television Sound) SYSTEM . . . . . . . . 22
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 23
■ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PLAYING A DVD VIDEO OR AN AUDIO CD . . . . . . . . . . 23
USING THE DVD MENUS . . . . . . . . . . . . . . . . . . . . . . . . . 23
USING THE TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . 24
PAUSING PLAYBACK OR DISPLAYING A STILL
PICTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
RESUMING PLAYBACK FROM THE POINT WHERE
PLAYBACK STOPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
STEPPING THROUGH FRAMES . . . . . . . . . . . . . . . . . . . . 24
FAST FORWARD/REVERSE . . . . . . . . . . . . . . . . . . . . . . . . 25
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
STARTING FROM A DESIRED TRACK . . . . . . . . . . . . . . . 25
PLAYING FROM A DESIRED TITLE OR A CHAPTER . . . 25
STARTING FROM A DESIRED TIME COUNT. . . . . . . . . . 26
MARKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RANDOM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PROGRAM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ZOOM PLAYBACK (enlargement on-screen) . . . . . . . . . . . . 28
PLAYING AN MP3 DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CHANGING THE ON-SCREEN DISPLAY DURING
MP3 DISC PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PLAYING A DESIRED TRACK FROM AN MP3 DISC . . . 30
PLAYING AN MP3 DISC RANDOMLY . . . . . . . . . . . . . . . 30
PLAYING AN MP3 DISC IN A PROGRAM. . . . . . . . . . . . . 30
■ SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CHANGING THE AUDIO LANGUAGE OR SOUND
MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CHANGING THE SUBTITLE LANGUAGE . . . . . . . . . . . . 32
CHANGING THE CAMERA ANGLE
(Multi-Angle Pictures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 33
BLACK LEVEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . 33
TruSurround SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
■ CHANGING THE SETUP ITEMS. . . . . . . . . . . . . . . . . . . . 34
LANGUAGE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DISPLAY SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
AUDIO SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
■ LANGUAGE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . 38
■ TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . 39
■ HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 40
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
■ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
INDICE
■ CONTROLES DEL FUNCIONAMIENETO Y SUS FUNCIONES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
■ CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
■ CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
DVD/VCR A CONEXIÓN DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
AJUSTANDO EL CONMUTADOR CH3/CH4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONECTANDO A UN TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONECTADO A UN TV QUE TIENE TOMA DE ENTRADA DE S-VÍDEO o TOMAS DE ENTRADA DE VÍDEO COMPONENTE . . . 46
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT . 46
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY O DESCODIFICADOR DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONECTANDO A UN AUDIO ANALÓGICO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
■ PREPARACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PREPARACIÓN DE CANAL AUTOMÁTICA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PREPARACIÓN DE RELOJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
–5–
EN
1L25
FEATURES
DVD Mode
¡Dolby Digital sound
¡On-screen display
This player can handle Dolby Digital surround sound
with 5.1 channels when connected to a Dolby Digital
decoder.
Information about the current operation can be displayed
on the TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
¡Still/fast/slow/step playback
Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in
random order.
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in any
desired order.
¡DVD menus in a desired language
You can display DVD menus in the desired language, if
available on the DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input
from the player for five minutes in the stop mode. When
the screen saver program has been activated for 30 minutes, the screen saver is automatically turned off.
¡DTS (Digital Theater System)
You can enjoy 5.1 channel surround system developed by
the Digital Theater System co. which reproduces the original sound as truthfully as possible.
¡Search
Chapter search: Search for a chapter designated by user is
possible.
Title search: Search for a title designated by user is possible.
Track search: Search for a track designated by user is
possible.
Time search: Search for a time designated by user is
possible.
¡Repeat
Chapter:
Repeated playback of the chapter of the
disc being played is possible.
Title:
Repeated playback of the title of the disc
being played is possible.
Track:
Repeated playback of the track of the disc
being played is possible.
Disc (audio CD): Repeated playback of the entire disc being
(MP3)
played is possible.
A-B:
Playback of the section between A and B
(designated by user) is possible.
Album:
Repeated playback of the album of the
MP3 disc being played is possible.
¡Subtitles in a desired language
You can select the desired language for the subtitle display, if that language is available on the disc.
¡Selecting a camera angle
You can select the desired camera angle, if the disc contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available on
the disc.
¡Parental lock
You can set the control level to limit playback of discs
which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡Playing an MP3 disc
You can enjoy MP3 files which are recorded on CDR/RW.
¡Direct Search
You can search for the desired title, chapter, and track with
the Number buttons during playback or in stop mode.
¡Zoom
A ×2 and ×4 magnified screen can be displayed.
¡Marker
A part designated by user can be called back.
¡Resume Play
User can resume playback from the part at which the play
was stopped even if the power is turned off.
¡SRS TruSurround
You can enjoy a stereophonic virtual space on your existing stereo system.
¡Component Video Out Jacks
Jacks located on the back of the DVD/VCR are used to
send high-quality video to a TV via Component Video In
Jacks.
¡Dimmer
This unit employs TruSurround system
of SRS Labs, Inc. as virtual
technology.
Brightness of the display can be varied.
¡Bit rate indication
¡DRC (Dynamic range control)
TruSurround and the
symbol are trademarks of
SRS Labs, Inc.
TruSurround technology is incorporated under license
from SRS Labs, Inc.
–6–
You can control the range of sound volume.
EN
1L25
Playback
VCR Mode
¡S-VHS Quasi Playback (SQPB)
Hardware specifications
(Allows you to view a tape recorded in S-VHS format.)
¡Auto Head Cleaner
¡Auto Repeat
¡4 Head HiFi Stereo
¡Bilingual on-screen menu display selectable in
¡2 Step Picture Search Operation
¡Index Search
English, French, or Spanish
¡181 channel capability PLL frequency synthesiz-
er tuner with direct station call
(A cable converter box may be necessary to view scrambled cable channels.)
Automatic functions
¡Time Search
Recording
¡1 Year, 7 events (including Daily and Weekly Timer
Recording)
¡OTR (One Touch Recording)
¡Auto power on system
Automatically turns the DVD/VCR on when you insert the
cassette.
¡Digital Auto Tracking (DTR)
PRECAUTIONS
INSTALLATION LOCATION
For safety and optimum performance of your DVD/VCR:
• Install the DVD/VCR in a horizontal and stable position. Do not place anything directly on top of the
DVD/VCR. Do not place the DVD/VCR directly on top
of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
on the sides of the DVD/VCR. Avoid locations subject
to strong vibration or strong magnetic fields.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR,
unplug the power cord immediately and take the unit to
our Authorized Service Center for servicing.
• Do not put your fingers or objects into the DVD/VCR
cassette holder.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when it is
moved from a cold place to a warm place, or after heating a
cold room or under conditions of high humidity. Do not use
the DVD/VCR at least for 2 hours until its inside is dry.
–7–
EN
1L25
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this
DVD/VCR.
[DVD]
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
Disc Type
Logo
Contents
Disc Size
12 cm
DVD
Video
Sound
and
Pictures
8 cm
Audio
CD
Sound
Maximum
Playback Time
Approx. 4 h
(single-sided)
Approx. 8 h
(double-sided)
Approx. 80 min
(single-sided)
Example
Approx. 160 min
(double-sided)
12 cm
74 min
8 cm
(singles)
20 min
Title 1
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡Some discs include region codes as shown below.
[AUDIO CD]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡The number inside the symbol refers to a region of the
Example
world, and a disc encoded in a specific region format
can only be played back on DVD/VCR with the same
region code.
The following discs cannot be played back on this
DVD/VCR.
¡DVD with region codes other than 1 or ALL.
¡DVD-ROM
¡DVD-RAM (Never attempt to play back,
otherwise a malfunction may result.)
¡CD-ROM
¡VSD
¡CDV (Only plays back the audio part.)
¡CD-G (Only plays back the sound.)
¡CD-R/CD-RW
(Only plays back discs on which audio CD or
MP3 are recorded.)
¡CD-I
(Never attempt to play back, otherwise a malfunction may result.)
¡SACD
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
[MP3]
Data on an MP3 is divided into sections called "albums",
and then into subsections called "tracks", each of which is
given an album or track number.
Example
Album 1
Track 1
Track 2
Track 3
Album 2
Track 4
Track 1
Track 2
¡Photo CD
(Never attempt to play back, otherwise a malfunction may result.)
¡Video CD
(Never attempt to play back, otherwise a malfunction may result.)
Any other discs without compatibility indications
–8–
EN
1L25
OPERATING CONTROLS AND FUNCTIONS
FRONT PANEL
1
2
3
4
5
6
78 9
POWER
VIDEO
CHANNEL
DVD OPERATION
VCR OPERATION
TIMER
SET
VCR/TV
OPEN/CLOSE
STOP
SKIP/REV
PLAY
FWD/SKIP
STOP/EJECT REW
PLAY
F.FWD REC/OTR
L
AUDIO
CST.IN
R
OUTPUT
25
26
REMOTE CONTROL
27
POWER SPEED
23
24
22
56
AUDIO
7.
28
1
2
8.
55
3
21
SKIP/CH.
4
29
5
9.
6
VCR/TV
7
8
9
0
+ 10
DVD
VCR
+100
DISPLAY
54
SLOW
53
PAUSE
30
51
31
PLAY
32
50
11.
49
STOP
33
10.
52
RECORD
34
35
37
39
SETUP
TITLE
38
MODE
ZOOM
40
47
ENTER
36
RETURN
SEARCH
MODE
SUBTITLE ANGLE REPEAT
41
12.
48
MENU
CLEAR/
C.RESET
13.
46
45
A-B
43
14.
44
42
1. Disc loading tray
2. DVD OUTPUT Light (Green) [page 13]
This light appears when the DVD/VCR is in DVD
mode. You can only watch DVDs when the green
DVD OUTPUT Light is on. To make the green DVD
OUTPUT light come on, press the DVD button on
the remote control or the OUTPUT Button on the
front panel.
3. VCR OUTPUT Light (Green) [page 13]
This light appears when the DVD/VCR is in VCR
mode. You can only watch tapes when the green
VCR OUTPUT light is on. To make the green VCR
OUTPUT light come on, the VCR button on the
remote control or the OUTPUT Button on the front
panel.
4. CASSETTE COMPARTMENT
5. REC/OTR Light [page 20]
Lights up during recording.
6. TIMER SET Light [page 21]
This light glows when the DVD/VCR is in standby
mode or off for a timer recording or during a OneTouch Recording. It flashes if the TIMER SET button is pressed for a timer recording, but there is no
15.
16.
17.
18.
–9–
19
20
17
18
15
16
13 11
14 12
10
tape in the DVD/VCR. It flashes when all timer
recordings or One-Touch Recordings are finished.
POWER Button [page 17]
Press to turn the power on and off.
POWER Light
Lights up when the power is on.
VIDEO In Jack
Connect a video cable coming from the video out
jack of a camcorder, another VCR, or a video source
(laser disc player, video disc player, etc.) here.
AUDIO In Jacks
Connect audio cables coming from the audio out jacks
of a camcorder, another VCR, or an audio source here.
TIMER SET Button [page 21]
Press to put the DVD/VCR into standby mode for a
timer recording.
CASSETTE IN Light [page 19]
Lights up when a cassette is in the DVD/VCR.
VCR/TV Light [page 17]
Lights up when the DVD/VCR is in the VCR position, and goes off when it is in the TV position.
CHANNEL Buttons [page 17]
In VCR mode, press to change TV channels on the
DVD/VCR; press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a Still picture.
REC/OTR Button (VCR) [page 20]
Press once to start a recording. Press repeatedly to
start a One-Touch Recording.
F.FWD Button (VCR) [page 17]
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback. (Forward
Search). When setting program (For example:setting
clock or timer program), press to determine your
selection and proceed to the next step you want to
input. Press to determine the setting modes from the
on screen menu. Press to add or delete channel numbers during channel preset.
PLAY Button (VCR) [page 17]
Press to begin playback. Press to enter digits when
setting program (For example: setting clock or timer
program). Press to select the setting modes from the
on screen menu.
REW Button (VCR) [page 18]
Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind
Search). Press to cancel a setting of timer program.
Press to correct digits when setting program (For
EN
1L25
example: setting clock or timer program). Press to
add or delete channel numbers during channel preset.
19. STOP/EJECT Button (VCR) [page 21]
●EJECT Button
Press to remove the tape from the VCR.
● STOP Button
Press to stop the tape motion. Press to enter digits
when setting program (For example:setting clock
or timer program). Press to select the setting
modes from the on screen menu.
20. OUTPUT Button [page 13]
Press to select DVD mode or VCR mode.
● You can switch the output mode either by pressing
the OUTPUT Button on the front panel, or by
pressing the DVD or the VCR Button on the
remote control. However, if you press the OUTPUT Button on the front panel first, you need to
re-select the corresponding mode by pressing
the DVD or the VCR button on the remote control.
21. FWD/SKIP Button (DVD) [page 25]
Plays back from the beginning of the next chapter or
track. Hold down to fast forward playback.
22. PLAY Button (DVD) [page 23]
Press to begin playback.
23. SKIP/REV Button (DVD) [page 25]
Plays back from the beginning of the current chapter
or track. Hold down to fast reverse playback.
24. STOP Button (DVD) [page 23]
Stops operation of the disc.
25. OPEN/CLOSE Button [page 23]
Press to insert discs into or remove them from the tray.
26. Display, Remote Sensor Window
27. SPEED Button [page 20]
Press to select the VCR’s recording speed (SP or SLP)
28. POWER Button
Press to turn the power on and off.
29. Number Buttons
● DVD mode [page 25]
Press to directly select a Track (Audio CD) for
playback.
Press to program Tracks (Audio CD) for playback.
● VCR mode [page 25]
Press to select TV channels on the DVD/VCR.
To select channels, enter channel numbers as a
two-digit number for the quickest results. For
example, to select channel 6, press 0 then 6.
+100 button:
If you want to select channels 100 and above, press
this button first, then press the last two digits. For
example, to select channel 125, press +100 button
first, then press 2 and 5.
30. DISPLAY Button
● DVD mode [page 13]
Press to access or remove the display screen during
DVD or Audio CD playback.
● VCR mode [page 13]
Press to access or remove the VCR’s on-screen status display.
31. DVD Button [page 13]
Press to select DVD mode for the remote control.
● You can switch the OUTPUT mode either by
pressing the OUTPUT Button on the front panel, or
by pressing the DVD or the VCR Button on the
remote control. However, if you press the OUTPUT
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
– 10 –
Button on the front panel first, you need to reselect the corresponding mode by pressing the
DVD or the VCR button on the remote control.
h Button
● DVD mode
Press to view the DVD picture in fast reverse
motion or to reverse playback of an Audio CD.
● VCR mode
Press to rewind the tape, or to view the picture
rapidly in reverse during the playback mode
(Rewind Search). Press to cancel a setting of
timer program. Press to correct digits when setting
program (For example: setting clock or timer program). Press to add or delete channel numbers
during channel preset.
Stop Button
Press to stop the tape motion. Press to enter digits
when setting program (For example: setting clock or
timer program). Press to select the setting modes
from the on screen menu.
RECORD Button
Press once to start a recording. Or, press repeatedly
to start a One-Touch Recording.
MENU Button
● DVD mode [page 23]
Press to display the menu of the Disc.
● VCR mode [page 17]
Press to access the VCR menu.
TITLE Button
SETUP Button [page 34]
Press to enter the setup mode or to change setup items.
ZOOM Button [page 28]
Enlarges part of a DVD-reproduced image.
MODE Button [pages 26]
Activates program playback or random playback
mode when playing CDs or MP3. Sets Black level or
SRS TruSurround.
SUBTITLE Button [page 32]
Press to select the desired subtitle language.
ANGLE Button [page 32]
Press to change the camera angle to see the sequence
being played back from a different angle.
REPEAT Button [page 27]
Repeats playback of the current disc, title, chapter or
track.
A-B REPEAT Button [page 27]
Repeats playback of a selected section.
SEARCH MODE Button
● DVD mode [page 25]
Press to access or remove the Search display,
which allows you to go directly to a specific
Title/Chapter/Track/Time.
● VCR mode [page 19]
Press to perform a Time Search or an Index Search.
CLEAR/C.RESET Button
● DVD mode [page 26]
Press to reset the setting.
● VCR mode [page 18]
Press to reset the counter. Press to exit from the
MENU screen.
RETURN Button
Returns to the previous operation.
Arrow Buttons
Use when making settings while watching the
display on a TV screen.
EN
1L25
48. ENTER Button
Press to accept a setting.
49. g Button
● DVD mode
Press to fast forward the Disc. Press the Pause button, then press the FWD button to begin slow
motion playback. Press the FWD button repeatedly to change the forward speed of slow motion.
● VCR mode
Press to rapidly advance the tape, or view the picture rapidly in forward during playback (Forward
Search). When setting program (For example: setting clock or timer program), press to determine
your selection and proceed to the next step you
want to input. Press to determine the setting
modes from the on screen menu. Press to add or
delete channel numberes during channel preset.
50. PLAY Button
● DVD mode
Press to begin playback.
● VCR mode
Press to begin playback. Press to enter digits when
setting program (For example: setting clock or
timer program). Press to select the setting modes
from the on screen menu.
REAR VIEW
57
51. VCR Button [page 13]
Press to select VCR mode for the remote control.
● You can switch the OUTPUT mode either by
pressing the OUTPUT Button on the front panel, or
by pressing the DVD or the VCR Button on the
remote control. However, if you press the OUTPUT
Button on the front panel first, you need to reselect the corresponding mode by pressing the
DVD or the VCR button on the remote control.
52. PAUSE Button
● DVD mode [page 24]
Press to pause Disc playback. Press repeatedly to
advance the DVD picture step by step (or one
frame at a time).
Notes
¡To use the remote control to operate the DVD/VCR
and its features, press the DVD button on the remote
control before pressing other DVD buttons. Verify
that the green DVD OUTPUT Light is on.
¡To use the remote control to operate the VCR and its
features, press the VCR button on the remote control
before pressing other VCR buttons. Verify that the
green VCR OUTPUT Light is on.
58
IN
59
60
DVD/VCR
OUT
COMPONENT
VIDEO OUT
ANT - IN
L
DVD/VCR
AUDIO OUT
AUDO
R
L
VIDEO
R
ANT - OUT
CH3 CH4
67 66 65
64 63
● VCR mode [page 19]
While recording, press to temporarily stop the
recording (pause). Press a second time to resume
normal recording. You can not pause a One-Touch
Recording. Or, press during tape playback to
freeze the picture. Press to advance the picture by
one frame at a time during still mode.
53. SLOW Button [page 19]
During tape playback, press to view the video tape in
slow motion. Press again to resume normal playback.
This button does not affect DVD playback.
54. VCR/TV Button [page 21]
Use to select VCR or TV position. If the VCR/TV
light appears on the front of the DVD/VCR, it is in
VCR position (in either VCR or DVD mode). If the
VCR/TV light doesn’t appear on the front of the
DVD/VCR, it is in TV position.
● VCR Position
When the green VCR OUTPUT light appears on the
front of the DVD/VCR, use the VCR to watch a tape,
watch a TV program while recording it, or watch a
TV broadcast using the CHANNEL or the Number
buttons to change channels at the DVD/VCR.
When the green DVD OUTPUT light appears on
the front of the DVD/VCR, use the DVD/VCR to
Y
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
Cr
62 61
view Disc playback or menus.
● TV Position
Use to watch TV (changing channels at the TV) or
watch one program while recording another.
55. SKIP/CH. Buttons
● DVD mode
Press to skip Chapters or Tracks.
● VCR mode
Press to change TV channels on the DVD/VCR.
56. AUDIO Button [page 31]
Press to select a desired audio language or sound mode.
57. AC Power Cord
Connect to a standard AC outlet to supply power
to the DVD/VCR.
58. AUDIO IN Jacks
Connect audio cables coming from the audio out
jacks of a camcorder, another VCR, or an audio
source here.
59. DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the
Audio In jacks of a television or other audio
equipment.
60. COMPONENT VIDEO OUT Jacks
Connect optional component video cables here
– 11 –
EN
1L25
61.
62.
63.
64.
and to the component Video In jacks of a television.
COAXIAL Jack
Connect an optional coaxial digital audio cable
here and to the Coaxial Digital Audio In jack of a
decoder or audio receiver.
S-VIDEO OUT Jack
Connect an optional S-Video cable here and to
the S-Video In jack of a television.
DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here
and to the TV’s Video In jack.
VIDEO IN Jack
Connect a cable coming from the video out jack
of a camcorder, another VCR, or an audio-visual
source (laser disc player, video disc player, etc.)
here.
65. CH3/CH4 Switch
Set to channel 3 or 4 to use your TV with your
DVD/VCR.
66. ANT-IN (Antenna In) Jack
Connect your antenna, Cable Box, or Direct
Broadcast System.
67. ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this
jack to the ANTENNA IN Jack on your TV.
Notes
¡The S-VIDEO OUT jack, COAXIAL jack, OPTICAL jack, and COMPONENT VIDEO OUT jacks
are only useful in DVD mode.
DISPLAYS DURING
OPERATION
DISPLAY
Lit when the
A-B repeat function
is on.
Lit when the
repeat function is on.
Lights up when a DVD
is inserted into the tray.
Power on
No disc inserted
Tray open
Tray closed
Lights up when the
inserted disc comes
to a pause.
Lights up when a
CD is inserted on
the tray.
Loading the Disc
Lit when the inserted
disc is being played back.
Displays how long the current title
or track has been playing. When a
chapter or track is switched, the
number of the new title, chapter or
track is displayed.
Power off
LOADING THE BATTERIES
1. Open the battery compartment
cover.
2. Insert two AA batteries, with each
one oriented correctly.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
– 12 –
EN
1L25
VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to switch one from
the other.
SWITCHING TO VCR MODE
SWITCHING TO DVD MODE
Press the VCR button on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
Press the DVD button on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
OR
OR
Press the OUTPUT button on the front panel, and then
press the VCR Button on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
Press the OUTPUT button on the front panel, and then
press the DVD Button on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
Notes
¡Pressing only the OUTPUT Button on the front panel does not switch the mode of the remote control. You
always need to select the correct mode on the remote control too.
POWER
VIDEO
POWER SPEED
AUDIO
CHANNEL
DVD OPERATION
VCR OPERATION
TIMER
SET
VCR/TV
OPEN/CLOSE
STOP
SKIP/REV
PLAY
FWD/SKIP
STOP/EJECT REW
PLAY
F.FWD REC/OTR
CSR.IN
L
AUDIO
R
OUTPUT
1
2
3
4
5
6
7
8
9
0
+ 10
DVD
VCR
SKIP/CH.
VCR/TV
DVD OUTPUT Light
DVD button
VCR OUTPUT Light
VCR button
DVD OPERATION
+100
DISPLAY
SLOW
PAUSE
PLAY
VCR OPERATION
STOP
PLAY
FWD/SKIP
RECORD
STOP/EJECT REW
OUTPUT
MENU
ENTER
OUTPUT button
SETUP
TITLE
MODE
ZOOM
RETURN
SEARCH
MODE
SUBTITLE ANGLE REPEAT
– 13 –
CLEAR/
C.RESET
A-B
EN
1L25
HOOKUPS
SETTING THE CH3/CH4
SWITCH
DVD/VCR TO TV CONNECTION
1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR.
4. Connect the DVD/VCR to the TV using the coaxial
cable.
5. Plug the AC power cords of the DVD/VCR and TV
into the AC outlets.
[VHF/UHF
combination antenna]
[Back of the DVD/VCR]
[Indoor antenna]
OR
[Cable box or satellite box]
If your TV does not have A/V terminals:
When the DVD/VCR is in the VCR Playback mode or
when the DVD/VCR is in the VCR mode, your TV will
receive signals from the DVD/VCR on either channel
3 or channel 4. To use the DVD/VCR with your TV, set
the selector switch to CH3 or CH4 (which is located in
the back of your DVD/VCR), whichever is not used for
normal broadcasts in your area. Then set your TV to
the same channel.
[Back of the
UHF/VHF combination TV]
Coaxial cable
(supplied)
ANT - IN
ANT - IN
CH3 CH4
UHF/VHF
OR
ANT - OUT
CH3 CH4
ANT - OUT
CH3 CH4
IN
From Cable or
Satellite Company
OUT
[Back of the DVD/VCR]
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
CONNECTING TO A TV
IN
Antenna/Cable signal
L
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
AUDO
A/V-compatible or
wide screen TV
DVD/VCR
OUT
ANT - IN
R
L
VIDEO
R
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
ANT - OUT
CH3 CH4
Cr
To ANT. IN
of TV
[Fig. 1]
To VIDEO OUT jack
To VIDEO INPUT jack
To Right (red) and Left (white)
AUDIO INPUT jacks
AUDIO OUT jacks
Notes
¡Connect the DVD/VCR directly to a TV. If the A/V cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
CONNECTING TO A TV THAT HAS AN
S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pictures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR. Therefore, in order to
use the VCR features or view TV channels on the DVD/VCR, you still need to either connect the RF coaxial cable
between the ANT-OUT jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video cable as
described earlier (Fig.1). To connect the supplied RF coaxial cable, see “DVD/VCR TO TV CONNECTION”
above.
IN
DVD/VCR
OUT
COMPONENT
VIDEO OUT
ANT - IN
L
AUDO
A/V-compatible or
wide screen TV
DVD/VCR
AUDIO OUT
R
L
VIDEO
R
ANT - OUT
CH3 CH4
Y
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
Cr
To Right (red) and Left (white)
AUDIO INPUT jacks
AUDIO OUT jacks
To S-VIDEO INPUT jack
To S-VIDEO OUT jack
– 14 –
[Fig. 2]
EN
1L25
FOR TVs WITH COMPONENT VIDEO IN JACKS
Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher quality pictures.
The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR. Therefore, in
order to use the VCR features or view TV channels at the DVD/VCR, you still need to either connect the RF coaxial cable between the ANT-OUT jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video
cable as described earlier (Fig. 1). To connect the supplied RF coaxial cable, see “DVD/VCR TO TV CONNECTION” on page 14.
A/V-compatible
or
wide screen TV
To COMPONENT VIDEO
INPUT jacks
To Right (red) and Left (white)
AUDIO INPUT jacks
To COMPONENT VIDEO
OUT jacks
To Right (red) and Left (white)
AUDIO OUTPUT jacks
DVD/VCR
OUT
IN
COMPONENT
VIDEO OUT
ANT - IN
L
Y
DVD/VCR
AUDIO OUT
AUDO
R
L
VIDEO
R
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
ANT - OUT
CH3 CH4
Cr
[Fig. 3]
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS SUCH AS MD DECK OR DAT DECK
Use an audio coaxial digital cables (not included) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
IN
DVD/VCR
OUT
COMPONENT
VIDEO OUT
ANT - IN
L
AUDO
DVD/VCR
AUDIO OUT
R
L
VIDEO
R
ANT - OUT
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
CH3 CH4
To COAXIAL DIGITAL
AUDIO INPUT jack
Y
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
Cr
To COAXIAL DIGITAL
AUDIO OUT jack
[Fig. 4]
Notes
¡The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner’s Manuals for the components to be connected to the DVD/VCR.
¡Set Dolby Digital and DTS to off for audio output in the setup mode. Playing a DVD disc using incorrect settings may generate noise distortion, and may also damage the speakers. (See page 36 to set Dolby Digital and
DTS to on)
– 15 –
EN
1L25
CONNECTING TO A DOLBY DIGITAL DECODER OR DTS DECODER
If using this DVD/VCR to play a DVD disc in 5.1 channel Dolby Digital surround, or DTS surround formats,
the DVD/VCR outputs a Dolby Digital, or DTS data stream from its COAXIAL DIGITAL AUDIO OUT jack.
By hooking the DVD/VCR up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic
ambience with powerful and high-quality surround sound of a professional standard such as can be heard in
movie theaters.
Use an audio coaxial digital cables (not included) for the audio connections.
DVD/VCR
OUT
IN
COMPONENT
VIDEO OUT
ANT - IN
L
Y
DVD/VCR
AUDIO OUT
AUDO
R
L
VIDEO
R
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
ANT - OUT
CH3 CH4
Center speaker
Front speaker
(left)
Surround
speaker
(left)
To COAXIAL DIGITAL
AUDIO OUT jack
Front speaker
(right)
Dolby Digital,
DTS decoder
Cr
To COAXIAL DIGITAL
AUDIO INPUT jack
Surround
speaker
(right)
Subwoofer
[Fig. 5]
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner’s Manuals for the components to be connected to the DVD/VCR.
¡If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio
output in the setup mode.
¡If the output is DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode.
¡Unless connected to a Dolby Digital decoder, or a DTS decoder, set Dolby Digital or DTS to off for audio output in the setup mode. Playing a DVD using incorrect settings may generate noise distortion, and may also
damage the speakers.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems Inc.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
CONNECTING TO AN ANALOG AUDIO
IN
DVD/VCR
OUT
COMPONENT
VIDEO OUT
ANT - IN
L
AUDO
DVD/VCR
AUDIO OUT
R
L
VIDEO
R
ANT - OUT
CH3 CH4
Y
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
Cr
Stereo system
To Right (red) and Left (white)
AUDIO OUT jacks
To ANALOG AUDIO INPUT jacks
[Fig. 6]
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR.
– 16 –
EN
1L25
SETUP
AUTOMATIC CHANNEL SET UP
VCR
The DVD/VCR can automatically program the tuner to
scan only the channels which are available in your area.
¡Channel memory programming is NOT needed
when the DVD/VCR is connected to a cable box or
a satellite box as in "DVD/VCR TO TV CONNECTION" on page 14. In this case, set the CH3/CH4
Switch (which is located on the back of your VCR)
to either CH3 or CH4, whichever is not used for normal broadcasts in your area. Then set your TV to the
same channel. The channel you want to record or
view will be selected from the cable or the satellite
box.
¡Follow the steps below once. Repeat only if there is
a power failure or if the DVD/VCR is unplugged for
more than 30 seconds. (In these cases, the programmed channels are erased.)
¡You must follow the steps below before attempting to
play or record a video tape.
5 Begin channel preset by pressing the F.FWD
button once. The tuner scans and memorizes
all active channels in your
CH 01
area.
AUTO SET UP
¡The DVD/VCR distinguishes
between standard TV channels
and cable channels.
6 After scanning, the tuner stops on the lowest
memorized channel.The TV screen returns to
TV mode.
¡If “AUTO SET UP” appears on the TV screen again,
check the cable connections. Press the F.FWD button once again and the DVD/VCR will begin preset
again.
TO SELECT A DESIRED CHANNEL
1 You need to connect the antenna or cable to
the DVD/VCR first. Then, connect the DVD
/VCR power plug to a standard AC outlet.
2 Turn on the TV and set the TV to channel 3 or
4.
¡Now set the CH3/CH4 switch on the back of the
You can select the desired channel by using the
CHANNEL(o/p) buttons or by directly pressing the
Number buttons on the remote control.
Note for using the Number buttons:
¡When selecting cable channels which are higher than
99, press [+100] first, then press the last two digits.
¡You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
DVD/VCR to match the channel selected on the TV.
3 Turn on the DVD/VCR by pressing the
TO PRESET THE CHANNELS AGAIN
POWER button. Both the POWER and the
VCR/TV light will come on.
1 Press the MENU button until the main menu
appears. (If you have already set the clock,
you only have to press it once. If not, you
have to press it twice).
4 Select the On Screen Language (“ENGLISH”,
“FRANCAIS” or “ESPAÑOL”) by pressing the
PLAY or the STOP button.
Then, press the F.FWD button.
2 Select “CHANNEL SET UP” by pressing the
PLAY or the STOP button. Then, press the
F.FWD button.
3 Select “AUTO SET UP” by pressing the PLAY
or the STOP button. Then, press the F.FWD
button.
¡After scanning, the tuner stops on the lowest memo-
rized channel.
– 17 –
EN
1L25
TO ADD/DELETE CHANNELS
CLOCK SET UP
When scanning, some channels may be skipped due to
a weak signal. In such cases, you can add the channels
to the DVD/VCR memory manually.
1
Press the MENU button until the main menu
appears. (If you have already set the clock,
you only have to press it once. If not you
have to press it twice).
- MENU TIMER PROGRAMMING
[OFF]
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
[ON]
TV STEREO
SAP
VCR
Set the clock accurately for proper automatic timer
recording. We suggest that you use a TV or radio station as your time source.
1 Press the MENU button twice to call up the
main menu. (If you have already set the
clock, you only have to press it once).
¡If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].
2 Select "CHANNEL SET UP" by pressing the
2 Select "CLOCK SET" by pressing the PLAY
PLAY or the STOP button. Then, press the
F.FWD button.
or the STOP button. Then, press the F.FWD
button
3 Select "MANUAL SET UP" by pressing the
PLAY or the STOP button. Then, press the
F.FWD button.
4 Enter the desired channel number by pressing the PLAY or the STOP button.
5 Add or Delete it from memory by pressing the
F.FWD or the REW button so that "ADD" or
"DELETE" flashes on the TV screen accordingly.
3 Set the clock.
1) Set the month
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
2) Set the day
Press the PLAY button or [STOP]repeatedly.
Then, press the F.FWD button.
3) Set the year
6 Exit the Preset mode by pressing the
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
The day of the week will appear automatically.
CLEAR/C.RESET button.
TO CHANGE THE ON-SCREEN
LANGUAGE
VCR
1
Press the MENU button twice to call up the
main menu. (If you have already set the
clock, you only have to press it once).
2 Select "LANGUAGE SELECT" by pressing
the PLAY or the STOP button. Then, press the
F.FWD button.
4) Set the hour
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
5) Set the minute
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
6) Set AM or PM
Press the PLAY button or the
STOP button repeatedly.
CLOCK SET
MONTH DAY
YEAR
03 / 18 MON 2002
HOUR MINUTE AM/PM
05 : 40
PM AM
PM
3 Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing the PLAY or the
STOP button. Then, press the
CLEAR/C.RESET button.
¡To go back one step, press the REW button.
4 Start the clock by pressing the
CLEAR/C.RESET or the F.FWD button.
– 18 –
EN
1L25
PLAYBACK FUNCTION
NORMAL PLAYBACK
2 Select "AUTO REPEAT" by pressing the
PLAY or the STOP button.
VCR
3 Begin auto repeat playback by pressing the
1 Insert a prerecorded tape. The DVD/VCR will
turn on, and the VCR/TV Light
and the CST IN Light comes
on.
F.FWD button so that [ON] appears next to
"AUTO REPEAT".
¡If the on-screen menu still remains, press the
CLEAR/C.RESET button to exit the menu.
¡If the safety tab has been removed, the DVD/VCR
¡To cancel the Auto repeat mode, press the F.FWD button at
step [3] so that [OFF] appears next to "AUTO REPEAT".
will start playback automatically.
SEARCH FUNCTIONS
2 Turn on the TV and set the TV to channel 3 or 4.
¡Now set the CH3/CH4 switch on the back of the
VCR
DVD/VCR to match the channel selected on the TV.
3 Begin playback by pressing the PLAY button.
¡Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press the CHANNEL(o/p) buttons on the DVD/VCR.
¡When a tape has reached the end, the DVD/VCR
will automatically rewind the tape to the beginning,
and eject the tape.
¡S-VHS Quasi Playback (SQPB): This unit allows
you to view a tape recorded in S-VHS format.
(Noise lines may appear on the picture.)
PICTURE SEARCH
If you want to skip or repeat a scene during playback,
press the F.FWD or the REW button.
¡Press it again and the DVD/VCR will now search at
super high speed. (in the LP/SLP modes only).
INDEX SEARCH
The index signal is recorded on the tape automatically
when the recording is started. If you want to view a
recording at a specific start point, this can be done easily.
1 Press the SEARCH MODE button so that the
Index Search menu appears.
2 Enter your desired number by pressing the
PLAY or the STOP button
within 30 seconds.
4 To stop playback, press the STOP button.
INDEX SEARCH
03
PAUSE/SLOW
You can freeze the picture on TV screen by pressing
the PAUSE button during playback.
¡You can advance the picture by one frame at a time
by pressing the PAUSE button during the Still mode.
¡If the picture begins to vibrate vertically during the
still mode, stabilize the picture by pressing the
CHANNEL(o/p) buttons.
¡If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if so equipped.
You can watch in the slow motion by pressing the
SLOW button during playback or the still mode.
¡If a noise bar appears on the TV screen, you can
reduce it by pressing the CHANNEL(o/p) buttons.
¡After the DVD/VCR has been in Still/Slow mode for
5 minutes, it will stop automatically to protect the
tape and the video head from damage.
¡To return to playback, press the PLAY button.
3 Press the F.FWD or the REW button to start
index search.
¡If you want to go in the forward direction, press the
F.FWD button. If you want to go in the reverse
direction, press the REW button.
¡After index search, the DVD/VCR will play the tape
automatically.
TIME SEARCH
This feature allows you to fast forward or rewind the
tape for the desired length of time.
1 Press the SEARCH MODE button twice so
that the Time Search menu appears.
2 Enter your desired time to
skip by pressing the PLAY
or the STOP button within
30 seconds.
TIME SEARCH
2 : 50
3 Press the F.FWD or the REW button to start
AUTO REPEAT PLAYBACK
VCR
This feature allows you to play a tape over and over.
1 Select main menu by pressing the MENU
time search.
¡If you want to go in the forward direction, press the
F.FWD button.
¡If you want to go in the reverse direction, press the
REW button.
¡After time search, the DVD/VCR will play the tape
button.
– 19 –
automatically.
EN
1L25
SPECIAL FEATURES
¡Always use video-quality shielded cables with
COPYING A VIDEO TAPE
VCR
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording DVD/VCR (this unit), the playing VCR (another source) and your TV using the following diagram.
¡You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
RCA-type connectors. Standard audio cables are not
recommended.
¡You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
TO MONITOR THE RECORDING
1 Turn on the TV and set the TV to channel 3 or 4.
¡Now set the CH3/CH4 switch on the back of the
DVD /VCR to match the channel selected on the TV.
2 Press the VCR/TV button on the recording
VCR so that the VCR/TV Light comes on.
[Recording VCR]
(this unit)
DVD/VCR
OUT
MTS (Multi-Channel Television
Sound) SYSTEM
COMPONENT
VIDEO OUT
IN
ANT - IN
L
AUDO
DVD/VCR
AUDIO OUT
Y
R
L
Cr
VIDEO
R
Cb
ANT - OUT
3CH 4CH
Coaxial cable
(supplied)
VCR
S-VIDEO DIGITAL AUDIO OUT
PCM / BITSTREAM
OUT
COAXIAL
When you play a VHS tape, or receive a broadcast on the
DVD/VCR tuner channel you are watching, the current
status will appear when you press
the DISPLAY button on the
1)*
remote control. When you record a
MTS broadcast signal, you need to
2)*
set it to MTS mode.
Audio/Video cables
(not supplied)
STOP
[TV set]
(Use for monitoring)
LEFT RIGHT
AUDIO
ANT in
OUT
SP
IN
VIDEO
[Playing VCR]
(another source)
12:00AM
CH 32
STEREO
SAP
0:00:00
HIFI
1)* When a program is broadcast in stereo,
STEREO appears. When a program is
broadcast in second audio, SAP appears.
1 Insert a pre-recorded tape into the playing
¡Although a program may be broadcast in both stereo
VCR.
and sub audio, you must select the Recording mode to
TV STEREO or SAP before you record a broadcast.
2 Insert a tape with a safety tab into the
2)* While the VCR is set in HiFi stereo mode,
recording VCR.
HiFi appears on the TV screen. While the
VCR is set in monaural (MONO) mode,
HiFi disappears from the TV screen.
3 Press the SPEED button on the recording
VCR to select the desired recording speed
(SP/SLP).
¡If you play non-HiFi tapes while the VCR is set in
HiFi, HiFi will disappear from the TV screen and the
VCR will automatically play in monaural.
DVD/VCR, select "L1" position by pressing [0], [0], [1]
on the remote control or the CHANNEL(o/p) buttons.
¡When you use the A/V input jacks on the front of the MTS RECORDING/MONITOR MODE
DVD/VCR, select "L2" position by pressing [0], [0], [2]
Display on the STEREO/SAP
Type of
Hi-Fi audio track
Normal audio
TV screen
broadcast
Selection
(2-channel)
track
on the remote control or the CHANNEL(o/p) buttons.
L-channel
R-channel
Regular
-None-InvalidNote
(monaural audio)
Mono
Mono
Mono
“L1” and “L2” are found before the lowest memoStereo
STEREO
-InvalidL
L+R
R
broadcast
rized channel. (Example: CH2)
SAP
TV STEREO* Main audio Main audio Main audio
¡When you use the A/V input jacks on the back of the
4 Press the REC/OTR button on the recording VCR.
Stereo &
Bilingual
broadcast
5 Begin playback of the tape in the playing
VCR.
¡For
Bilingual
broadcast
best results during dubbing, use the
DVD/VCR’s front panel controls whenever possible. The remote control might affect the playing
DVD/VCR’s operation.
SAP*
STEREO
SAP
TV STEREO*
SAP*
program
Sub audio
program
L
Sub audio
program
program
Sub audio
program
R
Sub audio
program
program
Sub audio
program
L+R
Sub audio
program
*
– 22 –
EN
1L25
AUTO REWIND
REAL TIME TAPE COUNTER
When a tape reaches the end during recording, playback, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
DVD/VCR will eject the tape and switch itself off.
¡The DVD/VCR will not rewind the tape automatically during timer recording or One Touch
Recording.
¡This shows the elapsed recording or playback time
in hours, minutes, and seconds. (The displayed time
will not change during blank portions of the tape.)
¡The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
PLAYING A DISC
PLAYING A DVD VIDEO
OR AN AUDIO CD
DVD
CD
Getting started
Turn on the power of the TV, amplifier and any other
components which are connected to the DVD/VCR.
(Change the input system to suite the DVD/VCR, and
check that the sound volume is correct).
1 Press the POWER button.
¡The power will turn on.
Notes
¡A “prohibited icon” may appear at
the top-right on the TV screen
during operation, warning that a
prohibited operation has been
encountered by the DVD/VCR or
the disc.
¡If a disc is dirty or has scratches, the pictures may
appear distorted and the playback operation may
stop. In such cases, clean the disc and unplug the
power cord and then plug it again before resuming
playback.
¡With DVDs that use titles for playback program
Check that the DVD OUTPUT Light is lit. If not
press the DVD button on the remote control to
switch to DVD/VCR mode.
signals, playback may start from the second title, or
it may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a malfunction.
2 Press the OPEN/CLOSE button.
¡The disc loading tray will open.
3 Place a disc into the tray.
USING THE DVD MENUS
¡Make sure the disc is sitting properly in the correct
recess, with the label side up.
DVD
Some DVDs contain their own menus, such as a guidance menu which describes the contents of the disc or
a selection menu for sound, language and other customized settings.
1 Press the MENU button.
4 Press the PLAY button.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
You need to press the PLAY button only when the
tray has been closed by pressing the OPEN/CLOSE
button.
¡The DVD menu will appear.
2 Select the desired title.
¡Press the arrow buttons (L/K/B/s) to change the
¡If your DVD has a title menu, it may appear on the
screen. In this case, refer to “USING THE DVD
MENUS” in the next section, or “USING THE
TITLE MENU” on page 24.
setting, and then press the ENTER button.
3 Playback will start from the selected title.
5 Press the STOP button to stop play.
– 23 –
EN
1L25
USING THE TITLE MENU
DVD
RESUMING PLAYBACK FROM
THE POINT WHERE
PLAYBACK STOPPED
DVD
With a DVD containing a title menu, you can select the
desired titles from the menu.
1 Press the TITLE button.
CD
1 Press the STOP button during playback.
¡Playback will stop, and then appear the resuming
message at the center.
¡The title menu will appear.
¡With some discs, a title menu may appear automati-
cally. In this case, skip to step 2.
Press 'PLAY' to play from here.
To play the beginning, press 'STOP' first
and then 'PLAY'.
2 Select the desired title.
¡Press the arrow buttons (L/K/B/s) to select a
desired title, and then press the ENTER button.
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVDs
2 Press the PLAY button. Playback will start
from the point where the previous playback
session was stopped.
B
¡Press the MENU button to call up the DVD menu.
¡Press the TITLE button to call up the title menu.
Note
¡The contents of menus and corresponding menu
operations may vary between discs. Refer to the
manual accompanying the disc for details.
PAUSING PLAYBACK OR
DISPLAYING A STILL PICTURE
DVD
Note
¡The resume function can be reset by pressing the
STOP button twice or by opening the disc loading
tray.
STEPPING THROUGH FRAMES
CD
DVD
1 Press the PAUSE button during playback.
¡Playback will pause, with sound
1 Press the PAUSE button while playback is
paused.
¡The next picture frame is dis-
F
muted.
F
played with sound muted each
time the button is pressed.
2 Press the PLAY button to resume playback.
2 Press the PLAY button to resume playback.
B
B
– 24 –
EN
1L25
STARTING FROM A DESIRED
TRACK
FAST FORWARD/REVERSE
DVD
CD
CD
1 Press the FWD g or the REV h button
1 Press the Number buttons to enter the
during playback.
¡For DVDs, pressing the FWD g or REV h but-
ton cycles the playback speed in four steps. In the
case of DVDs, the sound will mute.
¡For audio CDs, the playback speed is fixed at ×16.
REV
FWD
Button
Button
x2
x2
x8
x8
x30
x30
x60
x60
desired track number.
¡The selected track will be located, and playback will start.
You can also press the SEARCH
MODE button and use the Number
buttons to enter the track number.
When the track number is entered in the entry box,
playback of the desired track will start automatically.
TR : 5
TRICKS WITH THE SKIP BUTTONS (H, G)
If the SKIP button G is pressed during playback
or while playback is paused, the current track will
be skipped and the next track will start. If the SKIP
button H is pressed once, the beginning of the
current track will be located for replay. If the SKIP
button H is pressed again within 2 seconds
after playback begins, the previous track will be
located.
PLAYING FROM A DESIRED
TITLE OR A CHAPTER
2 Press the PLAY button to return to normal
DVD
playback speed.
There are two ways you can jump to a desired title or
a chapter.
SLOW MOTION
DVD
By using the ‘SEARCH MODE’ button.
1 Press the ‘SEARCH MODE’ button.
1 Press the FWD g button while playback is
¡The title/chapter search display will be displayed.
paused. (Sound remains muted.)
TT : 1/ 2
CH __ / 49
¡Slow motion mode will be activated.
¡Pressing the FWD g button cycles the playback
speed in three steps. Select the appropriate speed
while referring to the speed indication on the screen.
FWD
TT : _/ 12
CH : 12/ 49
2 If you wish to perform a title search, select
‘TT’. If you wish to perform a chapter search,
select ‘CH’ with K/ L buttons.
Button
×1/16
3 Enter the desired title or chapter number
with the Number buttons (If you are entering
a single digit number press “0” first).
×1/8
¡When you finish entering the number, the selected
title or chapter will start automatically.
Notes
¡If you didn’t press “0” before entering the single
digit number, you have to press ENTER to go to the
desired title or the chapter.
×1/2
2 Press the PLAY button to return to normal
playback speed.
Notes
¡Slow playback is not available with audio CDs.
¡Reverse slow motion is not available.
– 25 –
EN
1L25
By using only the Number buttons.
TITLE SEARCH:
MARKER
1 Directly enter the desired title number with the
DVD
Number buttons with playback stopped.
CHAPTER SEARCH:
1 Directly enter the desired chapter number
You can define the part to be called back.
with the Number buttons when the disc is
being played or paused.
1 Press the SEARCH MODE button three
times during playback.
¡When you finish entering the number, the selected
title or chapter will start automatically.
Notes
¡Play back from a desired title or chapter is not available with some DVDs.
¡If the title being played does not display the chapter
number, that means the chapter search function is
not available with that title.
TRICKS WITH THE SKIP BUTTONS (H, G)
If the SKIP button G is pressed during playback or
while playback is paused, the current chapter will be
skipped and the next chapter will start. If the SKIP
button H is pressed once, the beginning of the current chapter will be located for replay. If the SKIP
button H is pressed again within 2 seconds after
playback begins, the previous chapter will be located.
1 2 3 4 5 AC
NOT SET
Set the marker
¡Using the cursor (s/ B) buttons,
position the cursor on to the
marker number shown as “NOT SET”. Press the
ENTER button when the screen to be reviewed
appears. The marked time will be displayed. Up to
5 points can be marked.
Call back the marker
¡Using the cursor (s/ B) buttons, position the cursor
on to the marker number to be called back and press
the ENTER button.
Clear the marker
¡Using the cursor (s/ B) buttons, position the cursor
on to the marker number to be cleared and press the
CLEAR/C.RESET button.
To clear all markers, place the cursor on “AC” (All
clear markers) and press the ENTER button.
STARTING FROM A DESIRED
TIME COUNT
DVD
CD
2 Press the SEARCH MODE button or the
RETURN button to exit the display.
CD
RANDOM (Audio CD)
1 Press the SEARCH MODE button twice during playback or while paused.
CD
2 Press the Number buttons to set the desired
time count.
TIME 1:23:30
TOTAL 1:29:00
1 Press the MODE button in stop mode.
¡The program setting menu screen will appear.
¡Example: 1 hour, 23 minutes and
30 seconds
1→2→3→3→0
Notes
¡For a DVD, Time Search in Title is effective. (But
Time Search in Chapter is ineffective.)
¡For a CD, Time Search in Track is effective. (But
Time Search in the entire disc is ineffective.)
¡Playback from a desired time count is not available
with some discs or if the unit is in stop mode.
¡If the wrong numbers are entered, press the
CLEAR/C.RESET button and re-enter the correct
numbers.
2 Press the MODE button again.
RANDOM
START : PLAY
EXIT : MODE
3 Press the PLAY button. Random playback
will then start.
Note
¡Program playback is not available during random
playback.
– 26 –
EN
1L25
REPEAT
A-B REPEAT
DVD
CD
DVD
1 Press the REPEAT button during playback.
CD
You can define a section to be played back repeatedly.
For DVDs
1 Press the A-B REPEAT button during playback.
¡A single title or chapter can be played back repeat-
edly.
¡The starting point (A) will then be
REPEAT
[A- ]
selected.
¡Pressing the REPEAT button cycles the display on
the screen as follows.
REPEAT
[OFF]
No repeat playback.
2 Press the A-B REPEAT button again at the
REPEAT
[CHAPTER]
The current chapter is
played back repeatedly.
end point (B) of the desired section.
¡The selected section will be
played back repeatedly.
REPEAT
[TITLE]
REPEAT
[A-B]
The current title is
played back repeatedly.
3 To exit A-B repeat playback, press the A-B
For audio CDs
REPEAT button and set it to OFF.
REPEAT
[ OFF ]
¡The whole disc or a single track can be played back
repeatedly.
¡Pressing the REPEAT button cycles the display on
the screen through Off, Track and All.
Notes
¡With DVDs, the A-B repeat section can be set only
REPEAT
[OFF]
No repeat playback.
REPEAT
[TRACK]
The current track is
played back repeatedly.
within the current title.
¡With audio CDs, the A-B repeat section can be set
REPEAT
[ALL]
within the current track.
¡A-B repeat is not available with some scenes in
DVD.
The whole disc is
played back repeatedly.
¡To cancel the A point which was set, press the
CLEAR/C.RESET button.
¡A-B repeat playback does not function when title,
chapter, or repeat (all) playback has been set.
If the REPEAT button is pressed once during program/random playback, the current
track will be played back repeatedly.
If the REPEAT button is pressed again, the
program/random playback will be performed repeatedly.
Notes
¡Repeat playback is not available with some discs.
¡The REPEAT setting will be cleared when moving
to an other title, chapter or track.
¡Repeat playback does not function during A-B
repeat playback.
– 27 –
EN
1L25
ZOOM PLAYBACK
(enlargement on-screen)
PROGRAM (Audio CD)
CD
DVD
1 Press the MODE button in stop mode.
Images can be enlarged on the screen to your taste.
¡The program screen will appear.
PROGRAM
TIME
0:00:00
1 Press the ZOOM button during playback.
1/1
¡The image will be enlarged at the center of the
--
screen.
START: PLAY
RANDOM: MODE
¡Pressing the ZOOM button cycles the zooming
DELETE: CLEAR
EXIT: RETURN
images in two steps.
2 Press the Number buttons to enter the
ZOOM [x2]
ZOOM [x4]
ZOOM [OFF]
desired track numbers.
PROGRAM
¡50 programs can be displayed
at once on the screen. Press
“L” to go to the next page.
TIME 2:07:43
1/1
02 05 07 04 10 14 06 15 21 08
20 28 10 25 35 12 30 42 11 34
49 16 40 58 18 45 63 01 03 _
START: PLAY
RANDOM: MODE
DELETE: CLEAR
EXIT: RETURN
2
When the cursor (K/ L/ s / B) button is
pressed during zoom play, the part to be zoomed
moves.
3 Press the PLAY button.
¡The zooming frame can be moved from the center 4
¡Playback will start in the programmed order.
steps to the right, 4 steps to the left, 4 steps to the
top, and 4 steps to the bottom when times 2 zooming. The frames will move 6 steps when times 4
zooming.
¡While the program is being played back, the STOP
button works as follows.
¡Press the STOP button once and then press the
PLAY button again. Playback will restart from the
point where the STOP button was pressed. (Program
continued)
¡The current position will be displayed on the right-
bottom of the screen. Press the ENTER button, and
the display will disappear.
TO CLEAR THE PROGRAM
1 Press the STOP button twice, and the program will be cleared.
Notes
¡Adding programs is not possible during program
playback. You must stop the current playback before
such operations can be carried out.
¡Press the CLEAR/C.RESET button to cancel a pro-
gram. The most recently entered program will then
be deleted.
Note
¡Zooming function does not work while the disc
menu is being shown.
¡Up to 99 programs can be entered.
¡Playback from a desired track and random playback
are not available during program playback.
¡Program settings will be cleared when the power is
turned off or the disc loading tray is opened.
¡Press the MODE button to check the programmed
setting.
¡The programs will be cleared when you turn the
power off.
– 28 –
EN
1L25
CHANGING THE ON-SCREEN
DISPLAY DURING MP3 DISC PLAY
PLAYING AN MP3 DISC
MP3
MP3
The information on an MP3 disc in play can be
checked.
1 Insert an MP3 file recorded on disc.
¡The MP3 menu screen is displayed.
1 Press the DISPLAY button during playback.
¡Folders are referred to as
“Albums” and files are
referred to as “Tracks”.
¡“+” appears at the beginning
of the album name.
¡The track currently being
VOLUME LABEL
played will be highlighted.
FIRST PLAY
+ALBUM01
+ALBUM02
+ALBUM03
+ALBUM04
SELECT:
RETURN:
/
1/15
ALBUM NAME
A
TRACK11
TRACK12
TRACK13
TRACK14
TRACK15
ENTER:
START: PLAY
¡If all the tracks cannot be displayed at once on the
screen, “L” appears to go to the next page. If there
is a previous page, “K” appears on screen. To the
left of “L”, the current page and the total number of
pages are displayed.
2 Press the DISPLAY button again.
¡The album name being displayed will be replaced by
the elapsed time of the track.
¡
¡The player can recognize 255 albums and tracks
altogether.
0:02:31
2 Using the K/L buttons, select a album or a
track to be played.
[When a TRACK is selected]
Starting from the selected track,
the rest of the tracks will be
played in order.
will be displayed when repeat play has been
selected.
T: Track repeat
A: Album (folder) repeat
D: Disc repeat
A
TRACK11
TRACK12
TRACK13
TRACK14
TRACK15
ALBUM01
+ALBUM11
+ALBUM12
+ALBUM13
+ALBUM14
+ALBUM15
SELECT:
RETURN:
/
3 Press the DISPLAY button again, and the display screen disappears.
ENTER:
START: PLAY
[When an ALBUM is selected]
Press the B button. The track selection screen shows
up. Using the K/L buttons, select the tracks to be
played.
¡Choose “FIRST PLAY”, and the albums and tracks
will be played from the beginning of the disc.
¡Press the TITLE button, and the top hierarchy will
be called back.
¡Albums can be played up to the 8th hierarchy.
3 Press the PLAY button.
¡Playback will start.
4 To stop playing, press the STOP button.
– 29 –
EN
1L25
PLAYING A DESIRED TRACK
FROM AN MP3 DISC
PLAYING AN MP3 DISC IN A
PROGRAM
MP3
MP3
1 Press the MODE button in STOP mode.
1 Press the SEARCH MODE button during playback.
¡The program screen is displayed.
¡The SEARCH menu is displayed.
¡The track currently being played or in RESUME ON
PROGRAM-FOLDER NAME
will be highlighted. In the case of RESUME OFF,
the first track of the disc will be highlighted.
¡Press the RETURN button, and the SEARCH menu
disappears.
+ALBUM01
+ALBUM02
+ALBUM03
TRACK01
TRACK02
1/11
ALBUM NAME
+ALBUM01
TRACK11
TRACK12
TRACK13
TRACK14
SELECT:
RETURN:
/
1/1
START: PLAY
RANDOM: MODE
DELETE: CLEAR
EXIT: RETURN
2 Use the ARROW buttons (L/K) to select a
1/15
track. Then press the ENTER button to save
it in a program.
ENTER:
START: PLAY
PROGRAM - ALBUM01
+ALBUM11
+ALBUM12
TRACK11
TRACK12
TRACK13
1/11
2 Using the K/ L buttons, select the track to
be played. Then press the PLAY button to
start playing.
START: PLAY
RANDOM: MODE
Notes
TRACK11
1/1
DELETE: CLEAR
EXIT: RETURN
¡When an album name is highlighted, press the
directly. Just enter the track number with the
Number buttons.
¡If the track number entered is not available, the “dis-
L
button, and the next hierarchy is displayed.
¡During play, a desired track can be searched for
¡Press the
K button to go back to the previous hier-
archy.
¡If the entire program cannot be displayed at once on
able” symbol appears and the direct search mode is
cancelled.
the screen, “L” appears to go to the next page.
3 When the program has been selected, press
¡Playback cannot be started from a desired time
the PLAY button.
count.
¡The program will begin.
PLAYING AN MP3 DISC
RANDOMLY
Notes
¡Press the CLEAR/C.RESET button, and the last-
MP3
programmed entry will be deleted.
1 Press the MODE button twice in STOP mode.
¡Press the RETURN button, and the program screen
will be displayed and the program stored in memory.
¡The random setting menu screen will appear.
¡The program setting will be cancelled when the
RANDOM
power is turned off or the disc tray is opened.
PROGRAM - ALBUM05
START: PLAY
+ALBUM51
+ALBUM52
TRACK51
TRACK52
TRACK63
1/11
EXIT: MODE
START: PLAY
RANDOM: MODE
2 Press the PLAY button.
TRACK11
TRACK52
TRACK31
TRACK22
TRACK03
2/3
DELETE:
EXIT:
CLEAR
RETURN
¡Random play will begin.
– 30 –
EN
1L25
SETTINGS
Notes
¡Pressing the Audio button may not work on some
DVDs with multiple audio languages (e.g. DVDs
DVD
CD
which allow audio language setting on the disc
menu). Operation varies between discs, so refer to
the manual accompanying the disc.
The DVD/VCR has a function which allows you to
select the desired audio language and sound mode.
¡The current audio language and sound mode will be
displayed when you first press the AUDIO button.
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE
For DVDs
¡If the desired language is not shown after pressing
1 Press the AUDIO button during playback.
the Audio button several times, the disc does not
have an audio source in that language.
¡The current audio status will appear at the top.
¡The audio language resets to the one which was
selected in the setup mode every time the power is
2 Press the AUDIO button repeatedly until you
turned on or discs are replaced. If that language is
see the language of your choice.
not available on a disc, a language defined by the
¡The audio language mode can be changed only if the
disc will be selected.
disc is recorded with a multiple language setting.
¡The screen display will disappear after about 5
seconds.
¡If you use DIGITAL AUDIO OUT jack, the sound
mode of audio CDs can not be changed.
AUDIO 1.ENG DolbyD 5.1CH 48k/3
AUDIO 2.FRE DolbyD 5.1CH 48k/3
AUDIO 3.JPN DolbyD 5.1CH 48k/3
HELLO
Bon jour
For audio CDs
Press the AUDIO button during playback.
¡Pressing the AUDIO button cycles the sound mode
through STEREO, L-CH and R-CH.
AUDIO STEREO
Both right and left channels
are active (stereo).
AUDIO L-CH
Only the left channel is active.
AUDIO R-CH
Only the right channel is active.
– 31 –
EN
1L25
¡It may take time to display the subtitles in the
CHANGING THE SUBTITLE
LANGUAGE
DVD
The DVD/VCR has a function which allows you to
select the desired language for subtitles.
selected language.
¡The screen display will disappear after about 5
seconds.
¡When “SUBTITLE NOT AVAILABLE” appears on
screen, it means that no subtitle has been recorded.
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures)
1 Press the SUBTITLE button during playback,
and then press the SUBTITLE button to select the
desired subtitle language.
¡The subtitle language can be changed if the subtitles
are recorded in multiple languages on the DVD
being played.
¡The subtitle language cannot be changed if the
subtitles are recorded in a single language on the
DVD being played.
DVD
The DVD/VCR has a function which allows you to
select the desired camera angle.
1 Press the ANGLE button during playback.
¡If the disc contains sequences recorded from differ-
ent camera angles, the angle icon (
) will appear
at the top-right of the screen. You can change the
camera angle when the icon appears on the screen.
SUBTITLE 1.ENG/6
Subtitle 1
¡The camera angle cannot be changed if the disc does
SUBTITLE 2.FRE/6
not contain sequences recorded from different
camera angles.
Subtitle 2
2 Press the ANGLE button while the angle
SUBTITLE OFF
OFF
number is shown on the screen.
ANGLE 1 / 8
¡Pressing the SUBTITLE button cycles the subtitle
Angle 1
language from SUBTITLE 1, SUBTITLE 2 and all
the languages recorded.
¡The current subtitle mode will be displayed when
you first press the SUBTITLE button.
¡Press the SUBTITLE button, and then press the cursor (s/ B) button to set it to on or off.
ANGLE 2 / 8
Angle 2
ANGLE 8 / 8
Angle 8
HELLO
Bon jour
Notes
¡Some discs allow subtitle language setting on the
disc menu. (Operation varies between discs, so refer
to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
¡The subtitle language resets to the one which was
selected in the setup mode, every time the power is
turned on or discs are replaced. If that
language is not available on a disc, a language
defined by the disc is selected.
Notes
¡The screen display will disappear after about 5
seconds.
¡The current camera angle will be displayed when
you first press the ANGLE button.
– 32 –
EN
1L25
CHANGING THE ON-SCREEN
DISPLAY
DVD
2 Press the DISPLAY button again.
CD
ALL 4/12 0:13:45 -0:45:40 B
ALL:
Current track number
/ the total number of
tracks.
You can check the information regarding the disc by
pressing the DISPLAY button on the remote control.
TIME:
Elapsed time of the
current disk and
remaining time of
the current disc.
For DVDs
¡Use the Number buttons to start from a desired
1 Press the DISPLAY button during playback.
3 Press the DISPLAY button or the RETURN but-
CH 7/49 0:01:46 -0:03:27
ton to exit the display.
TIME:
Elapsed time of the
current chapter and
remaining time of the
current chapter.
CH (Chapter):
Current chapter number
/ the total number of
chapters.
BLACK LEVEL SETTINGS
DVD
You can select the BLACK LEVEL ON to make the
black areas of the picture brighter.
2 Press the DISPLAY button again.
TT
1/2
1 Press the MODE button during playback.
0:00:00 -1:23:45
TT(Title):
Current title number
/ the total number of
titles.
TIME:
Elapsed time of the
current title and remaining
time of the current title.
¡The setup screen is displayed.
BLACK LEVEL : ON
2 Press the ENTER button to turn it on or off.
¡Use the Number button to start from the desired
chapter.
¡ON: This makes the dark parts brighter. (Default:
3 Press the DISPLAY button again.
ON)
OFF: The original picture which is recorded on the
disc will be shown.
¡Press the RETURN button to exit the display.
BIT RATE
BIT RATE indicator will appear.
BIT RATE shows the quantity of
information which is recorded on the DVD.
C L0
Layer number (*)
L0: Layer 0 is playing
L1: Layer 1 is playing
Current Repeat setting
C: Chapter repeat
T: Title repeat
A B: A-B repeat
TruSurround SETTINGS
You can enjoy stereophonic sound system when you
playback Dolby Digital and PCM 48 kHz sound.
1 Press the MODE button twice during playback.
* appears when a layered disc is playing.
4 Press the DISPLAY button or the RETURN but-
¡The setup screen will appear.
SRS TruSurround ON
ton to exit the display.
2 Press the ENTER button to set it on or off.
For audio CDs
1 Press the DISPLAY button during playback.
TR
TR (Track):
Current track number
/ the total number of
tracks.
4/12 0:03:21 -0:02:15 B
ON: TruSurround ON.(Default : OFF)
OFF: TruSurround OFF.
¡Press the DISPLAY button ( you may have to press
it more than once), or press the RETURN button to
exit the display.
TIME:
Elapsed time of the
current track and
remaining time of
the current track.
– 33 –
EN
1L25
CHANGING THE SETUP ITEMS
PLAYER MENU:
(The on-screen display appears in selected language.)
LANGUAGE SETTINGS
DVD
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
1 Press the SETUP button in STOP mode.
ORIGINAL
OFF
ORIGNAL
ENGLISH
¡The setup screen is displayed.
SELECT: /
EXIT: SETUP
SET:
ENTER
CANCEL: RETURN
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT: /
EXIT: SETUP
4 Press the K/ L buttons to select a desired
item, and then press the ENTER button.
SET:
ENTER
CANCEL: RETURN
¡If “OTHER” is selected on the AUDIO, SUBTITLE
or DISC MENU setting screen, the Language Code
setting screen will appear. Press the Number buttons
to enter the desired language code while referring to
the list on page 38.
2 Press the K/ L buttons to select Language,
and then press the ENTER button.
SET-UP
SET-UP
LANGUAGE CONTROLS
DISC MENU
LANGUAGE CODE
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
Please enter a 4-digit Language code.
----
SELECT: /
EXIT: SETUP
SET:
ENTER
CANCEL: RETURN
EXIT: SETUP
3 Press the K/ L buttons to select an item, and
5 Press the SETUP button.
then press the ENTER button.
AUDIO:
(Voice is played in selected language.)
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
SELECT: /
EXIT: SETUP
ORIGINAL
OFF
ORIGNAL
ENGLISH
SET:
ENTER
CANCEL: RETURN
SUBTITLE:
(Subtitles are shown in selected language.)
CANCEL: RETURN
¡The setup mode will be canceled and the ordinary
screen is displayed.
Notes
¡Language Setting for Audio and Subtitle is not available with some discs, so use the Audio and the
Subtitle button. Details are on pages 31 and 32.
¡You can also select an item by entering the number
besides it using the Number buttons.
¡When you change the setup items, press the STOP
button if you are in playback mode.
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
SELECT: /
EXIT: SETUP
ORIGINAL
OFF
ORIGNAL
ENGLISH
SET:
ENTER
CANCEL: RETURN
DISC MENU:
(The disc menu appears in selected language.)
SET-UP
LANGUAGE CONTROLS
1.AUDIO
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
SELECT: /
EXIT: SETUP
ORIGINAL
OFF
ORIGINAL
ENGLISH
SET:
ENTER
CANCEL: RETURN
– 34 –
EN
1L25
DISPLAY SETTINGS
ANGLE ICON (Default: ON)
Display or not display the Angle icon on the screen.
DVD
SET-UP
DISPLAY CONTROLS
1 Press the SETUP button in STOP mode.
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF
5.BACKGROUND
¡The setup screen will appear.
SELECT: /
EXIT: SETUP
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT: /
EXIT: SETUP
4:3 LETTER BOX
BRIGHT
ON
ON
BLUE
SET:
ENTER
CANCEL: RETURN
AUTO POWER OFF (Default: ON)
Set or not set to turn off after the screen saver is started and
no keys are pressed for 35 minutes.
SET:
ENTER
CANCEL: RETURN
SET-UP
DISPLAY CONTROLS
2 Press the K/ L buttons to select DISPLAY
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF
5.BACKGROUND
and then press the ENTER button.
SELECT: /
EXIT: SETUP
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT:
EXIT:
/
SETUP
4:3 LETTER BOX
BRIGHT
ON
ON
BLUE
SET:
ENTER
CANCEL: RETURN
BACKGROUND COLOR (Default: BLUE)
Select blue or gray.
SET:
ENTER
CANCEL: RETURN
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF
5.BACKGROUND
3 Press the K/ L buttons to select an item, and
then press the ENTER button.
SELECT: /
EXIT: SETUP
TV ASPECT (Default: 4:3 LETTER BOX)
4:3 LETTER BOX: Wide screen with black bars on top and
bottom
4:3 PAN & SCAN: Full height picture, trimmed both sides
16:9 WIDE: If wide screen TV is connected
4:3 LETTERBOX
BRIGHT
ON
ON
BLUE
SET:
ENTER
CANCEL: RETURN
4 Press the K/ L buttons to select a desired
item, and then press the ENTER button to
change the setting.
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF
5.BACKGROUND
SELECT:
EXIT:
/
SETUP
4:3 LETTER BOX
BRIGHT
ON
ON
BLUE
SET:
ENTER
CANCEL: RETURN
5 Press the SETUP button.
SET-UP
DISPLAY CONTROLS
TV ASPECT
1.4:3 LETTER BOX
2.4:3 PAN & SCAN
3.16:9 WIDE
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
¡The setup mode will be canceled and the ordinary
screen will appear.
Notes
¡You can also select an item by entering the number
besides it using the Number buttons.
PANEL DISPLAY (Default : BRIGHT)
Adjust the brightness of the display of the unit.
Auto: Stays dim only during playback.
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF
5.BACKGROUND
4:3 LETTER BOX
BRIGHT
ON
ON
BLUE
SET-UP
DISPLAY CONTROLS
PANEL DISPLAY
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
1.BRIGHT
2.DIMMER
3.AUTO
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
– 35 –
EN
1L25
AUDIO SETTINGS
DVD
DTS (Default: OFF)
On : Output DTS sound
Set to On when the unit is connected to DTS
Decoder.
SET-UP
1 Press the SETUP button in STOP mode.
¡The setup screen will appear.
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT:
EXIT:
SELECT: /
EXIT: SETUP
/
SETUP
OFF
ON
OFF
AUTO
SET:
ENTER
CANCEL: RETURN
SET:
ENTER
CANCEL: RETURN
2 Press the K/ L buttons to select Audio and
then press the ENTER button.
Down Sampling (Default: AUTO)
Set the output for the DVD
recorded in PCM 96 kHz (96 kHz or 48 kHz)
¡Press the K/L buttons to select an item, and then
SET-UP
press the ENTER button.
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SETUP MENU
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
AUDIO OPTIONS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
3 Press the K/ L buttons to select an item, and
then press the ENTER button.
SELECT:
EXIT:
DRC (Default: OFF)
On: DRC
(Dynamic Range Control)
¡This function is for controlling the range of sound
volume. By compressing the range of sound volume,
it is possible not only to suppress the output of loud
sound at night and but also to raise the volume of
low sound.
SET:
ENTER
CANCEL: RETURN
SET-UP
AUDIO CONTROLS
DOWN SAMPLING
1.AUTO
2.48kHz
3.96kHz
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
When playing a disc with copyright protection
¡If you select 96 kHz, copyright protection will be
activated and no sound will come out. If you select
AUTO, sound will be down sampled at 48 kHz.
¡This function is effective only for the sound record-
ed by Dolby Digital recording.
4 Press the SETUP button.
SET-UP
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
SELECT:
EXIT:
/
SETUP
OFF
ON
OFF
AUTO
/
SETUP
OFF
ON
OFF
AUTO
¡The setup mode will be canceled and the ordinary
screen will appear.
SET:
ENTER
CANCEL: RETURN
Dolby Digital (default: ON)
On : Output by Dolby Digital
Set to On when the unit is connected to a Dolby
Digital Decoder.
SET-UP
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
4.DOWN SAMPLING
SELECT:
EXIT:
/
SETUP
OFF
ON
OFF
AUTO
SET:
ENTER
CANCEL: RETURN
– 36 –
EN
1L25
When Parental Level is selected
¡Press the K/ L buttons to select an
PARENTAL LOCK
DVD
item from “ALL” or 8 to 1 and
then press the ENTER button.
1 Press the SETUP button in STOP mode.
SET-UP
¡The setup screen will appear.
PARENTAL CONTROLS
1.PARENTAL LEVEL
2.CHANGE
ALL
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SELECT:
EXIT:
SELECT:
EXIT:
/
SETUP
/
SETUP
SET:
ENTER
CANCEL: RETURN
SET-UP
PARENTAL CONTROLS
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
5
SET:
ENTER
CANCEL: RETURN
SELECT:
EXIT:
/
SETUP
SET:
ENTER
CANCEL: RETURN
2 Press the K/ L buttons to select PARENTAL,
and then press the ENTER button.
5 Press the SETUP button.
¡The setup mode will be canceled and the ordinary
SET-UP
screen will appear.
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
CONTROL LEVELS
SELECT: /
EXIT: SETUP
SET:
ENTER
CANCEL: RETURN
¡ALL
All parental lock is cancelled.
3 Press the Number buttons to enter a 4-digit
¡Level 8
DVD software of any grade (adult/general/children)
can be played back.
password (you can use any 4-digits except
for 4737), and then press the ENTER button.
¡This number will be used as the password from the
second time onward.
¡By entering the password, you can then change the
control level and password settings.
¡Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
¡Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
¡If you want to change the password, select
“CHANGE” and enter a new password. Then press
the ENTER button.
SET-UP
Notes
PARENTAL CONTROLS
PASSWORD
¡With some DVDs, it may be difficult to find if they
Please enter a 4-digit password.
----
EXIT: SETUP
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
CANCEL: RETURN
¡Record the password in case you forget it.
4 Press the K/ L buttons to select an item, and
then press the ENTER button.
IF YOU FORGET THE PASSWORD
1) Press 4, 7, 3, and 7 at Step 3.
¡Password will be cleared and parental level will be
set to ALL.
2) Proceed the above Steps 3-5 again.
– 37 –
EN
1L25
LANGUAGE CODE LIST
No.
Language
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali; Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish [DAN]
German [GER]
Bhutani
Greek [GRE]
English [ENG]
Esperanto
Spanish [SPA]
Estonian
Basque
Persian
Finnish [FIN]
Fiji
Faroese
French [FRE]
Frisian
Irish [IRI]
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian [HUN]
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic [ICE]
Italian [ITA]
Hebrew
Japanese
Yiddish
Japanese [JPN]
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean [KOR]
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Country code
No.
4747
4748
4752
4759
4764
4765
4771
4772
4847
4851
4853
4854
4855
4860
4861
4864
4947
4961
4965
4971
5047
5051
5072
5158
5160
5161
5165
5166
5167
5247
5255
5256
5261
5264
5271
5347
5350
5358
5360
5367
5447
5455
5464
5467
5471
5547
5551
5557
5560
5565
5566
5569
5647
5655
5669
5747
5757
5758
5759
5760
5761
5765
5767
5771
5847
5860
5861
5866
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
Language
Latvian; Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch [DUT]
Norwegian [NOR]
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto; Pushto
Portuguese [POR]
Quechua
Rhaeto-Romance
Kirundi
Romanian [RUM]
Russian [RUS]
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswat
Sesotho
Sundanese
Swedish [SWE]
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish [TUR]
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Chinese [CHI]
Zulu
Country code
5868
5953
5955
5957
5958
5960
5961
5964
5965
5966
5971
6047
6051
6058
6061
6149
6159
6164
6247
6258
6265
6266
6367
6459
6460
6461
6467
6469
6547
6550
6553
6554
6555
6557
6558
6559
6560
6561
6563
6564
6565
6566
6567
6568
6569
6647
6651
6653
6654
6655
6657
6658
6660
6661
6664
6665
6666
6669
6757
6764
6772
6855
6861
6961
7054
7161
7254
7267
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on pages 31 and 32. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language codes are written in square brackets.)
EN
– 38 –
1L25
TROUBLESHOOTING GUIDE
If the DVD/VCR does not perform properly when operated as instructed in this Owner's Manual, check the
player consulting the following checklist.
D
V
D
V
C
R
V
C
R
D
V
D
PROBLEM
CORRECTIVE ACTION
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The player does not respond to. • Check if the power plug is connected to an AC outlet.
the remote control.
• Check the batteries in the remote control.
.
• Aim the remote control directly at the remote sensor. If necessary, remove all the
obstacles between the sensor and the remote.
• You have to be within 7 m of the player.
• Check if the correct mode is selected. If not switch the mode by pressing the DVD or
the VCR button, whichever you need, on the remote control.
Timer recording is impossible. • Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the DVD/VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Put he player in VCR mode. Press the VCR button on the remote control so that the green
VCR OUTPUT light is lit.
) button on the
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing the CHANNEL (
DVD/VCR.
Cannot view a tape but the
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
audio is OK.
• Make sure the DVD/VCR is not in the Menu mode.
No, or poor, playback picture.
• Select channel 3 or 4 on your TV, then press the VCR/TV button so that the VCR/TV
indicator on the VCR comes on.
• Fine tune your TV.
TV programs cannot be seen
• Re-check the ANT. IN and ANT. OUT connections. See page 14.
normally.
• Press the VCR/TV button so that the VCR/TV indicator on the DVD/VCR disappears.
• Press the VCR button on the remote control to put it in the VCR mode. Check if the green
VCR OUTPUT light is lit. Then, set it to the TV position by pressing the VCR/TV button.
The VCR/TV light goes off.
Video or color fades in and out • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
when making a copy of a video tape.
Cannot remove the tape.
• Check if the player is in the VCR mode. If not, press the VCR button on the remote control
to switch the mode.
No picture.
• Connect the video cables firmly.
• Insert a correct video disc that plays on this player.
• Press the DVD button on the remote control. Check if the DVD OUTPUT Light is lit. Then
try other DVD feature buttons.
• Insert the disc.
Disc cannot be played.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
No sound.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• Connect the player directly to the TV.
Distorted picture.
• There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
• The selected language is not available for audio or subtitles on the DVD.
does not match the set up
This is not a malfunction
The camera angle cannot be
changed.
Audio or subtitle language
cannot be changed.
“Prohibited icon” appears on the
screen, prohibiting an operation.
• The DVD does not contain sequences recorded from different camera angles.
This is not a malfunction.
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
• That operation is prohibited by the player or the disc.
This is not a malfunction.
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this
Owner’s Manual for details on correct operations.
¡Playback from a desired track and random playback are not available during program playback.
– 39 –
EN
1L25
HANDLING PRECAUTIONS
SERVICING
AUTO HEAD CLEANING
Should your DVD/VCR become inoperative, do not try
to correct the problem by yourself. There are no userserviceable parts inside. Turn off, unplug the power
cord, and please call our help line at 1-800-256-2487 to
locate an Authorized Service Center.
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while
the TV program reception is clear. Dirt accumulated on the
video heads after long periods of use, or the usage of
rental or worn tapes can cause this problem. If a streaky or
snowy picture appears during playback, the video heads in
your DVD/VCR may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line at 1-800-242-7158 to locate an
Authorized Service Center.
CABINET CLEANING
¡Wipe the front panel and other exterior surfaces of
the DVD/VCR with a soft cloth immersed in
lukewarm water and wrung dry.
¡Never use a solvent or alcohol. Do not spray
insecticide liquid near the DVD/VCR. Such
chemicals may cause damage and discoloration to
the exposed surfaces.
NOTES:
• Remember to read the instructions included with the video
head cleaner before use.
• Clean video heads only when problems occur.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
¡If the player still does not perform properly when it is operated while referring to the relevant sections and to
the TROUBLESHOOTING GUIDE in this Owner’s Manual, the laser optical pickup unit may be dirty.
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup
DISC HANDLING
¡Use discs which have the following logos on them.
(Optical audio digital discs.)
¡To clean-off, use a soft cloth.
¡Do not use a hard cloth since this will mar the disc.
¡Wipe the disc in a straight line from center to edge.
¡Never wipe with a circular motion.
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Do not use detergent or abrasive cleaning agents.
¡Always store the disc in its protective case when it is
not used.
– 40 –
EN
1L25
SPECIFICATIONS
Product type:
DVD player with Video Cassette Recorder
Discs:
DVD video
Audio CD
Video Cassette tape
Converter output:
VHF Channel 3 or 4.
Power source:
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption:
25 W (standby: 7.2 W)
Operating temperature:
5°C to 40°C
Dimensions:
W 17-1/8” (435 mm)
H 4” (99 mm)
D 10-1/2” (266 mm)
Weight:
8.8 lbs (4 kg)
¡Designs and specifications are subject to change without notice.
¡If there is a discrepancy between languages, the default language will be English.
– 41 –
EN
1L25
CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES
PANEL DELANTERO
1
2
3
4
5
6
78 9
POWER
VIDEO
CHANNEL
DVD OPERATION
VCR OPERATION
TIMER
SET
VCR/TV
OPEN/CLOSE
STOP
SKIP/REV
PLAY
FWD/SKIP
STOP/EJECT REW
PLAY
F.FWD REC/OTR
L
AUDIO
CST.IN
R
OUTPUT
25
26
23
24
21
22
19
20
17
18
15
16
13 11
14 12
10
PANEL REMOTO
27
POWER SPEED
56
AUDIO
28
1
2
10.
55
3
SKIP/CH.
29
4
5
7
8
6
VCR/TV
9
+100
DISPLAY
0
+ 10
DVD
VCR
PAUSE
51
PLAY
32
52
12.
50
13.
49
STOP
33
11.
53
30
31
54
SLOW
RECORD
34
35
37
39
48
MENU
36
SETUP
TITLE
38
MODE
ZOOM
RETURN
SEARCH
MODE
SUBTITLE ANGLE REPEAT
41
40
14.
47
ENTER
CLEAR/
C.RESET
46
45
A-B
43
44
15.
42
1. Bandeja de carga del disco
2. Luz DVD OUTPUT (verde)
Esta luz aparece cuando el DVD/VCR está en modo DVD.
Usted sólo puede mirar DVDs cuando la Luz DVD OUTPUT verde está encendida. Para hacer que la Luz DVD
OUTPUT verde se encienda, presione el Botón DVD en el
control remote o el Botón OUTPUT en el panel delantero.
3. Luz VCR OUTPUT (Verde)
Esta luz aparece cuando el DVD/VCR está en el modo
VCR. Usted puede sólo mirar cintas cuando la Luz VCR
OUTPUT verde está encendida. Para hacer que la Luz VCR
OUTPUT verde se encienda, presione el Botón VCR en el
control remote o el Botón OUTPUT en el panel delantero.
4. CASSETTE COMPARTMENT
5. Luz REC/OTR
Se enciende durante la grabación.
6. Luz TIMER SET
Esta luz brilla cuando el DVD/VCR está en el modo espera
o apagada para una grabación con temporizador o durante
una grabación de Un-Toque, Parpadea si se presiona Botón
TIMER SET para una grabación con temporizador, pero no
hay cinta en el DVD/VCR. Parpadea cuando todas las
grabaciones con temporizador o grabaciones de Un-Toque
han terminado.
7. Botón POWER
Presione para conectar y desconectar la alimentación.
8. Luz POWER
Se enciende cuando la alimentación está conectada.
9. Toma VIDEO IN
16.
17.
18.
19.
– 42 –
Conecte aquí un cable de videó procedente de la toma de
salida de videó de un camcorder, otro VCR o una fuente de
videó (reproductor de discos láser, reproductor de cintas de
videó, etc.).
Tomas AUDIO IN
Conecte aquí cables de audio procedentes de las tomas de salida de audio de un camcorder, otro VCR o una fuente de audio.
Botón TIMER SET
Presione para poner el DVD/VCR en modo de espera para
una grabación con temporizador.
Luz CASSETTE IN
Se enciende cuando un cassette está en el DVD/VCR.
Luz VCR/TV
Se enciende cuando el DVD/VCR está en la posición VCR,
y se apaga cuando está en la posición TV.
Botones CHANNEL
En el modo VCR, presione para cambiar canales TV en el
DVD/VCR; presione para ajustar el seguimiento durante
reproducción de movimiento normal o lento; presione para
remover fluctuaciones verticales en una imagen fija.
Botón REC/OTR (VCR)
Presiones una vez para iniciar una grabación. Presione
repetidamente para iniciar un grabación de Un-Toque.
Botón F.FWD (VCR)
Presione para avanzar rápidamente la cinta o ver la
imagen rápidamente en avance durante reproducción. (Búsqueda en Avance). Cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador), presione para determinar su selección y
proceder al siguiente paso que usted desea entrar.
Presione para determinar los modos de ajuste del
menú en pantalla. Presione para añadir o cancelar
números de canal durante preajuste de canal.
Botón PLAY (VCR)
Presione para comenzar reproducción. Presione para
entrar dígitos cuando ajuste programa. (Por ejemplo:
ajuste reloj o programa con temporizador). Presione
para seleccionar los modos de ajuste del menú en
pantalla.
Botón REW (VCR)
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de reproducción.(Búsqueda en Rebobinado). Presione para
cancelar un ajuste de programa con temporizador.
Presione para corregir dígitos cuando ajuste programa. (Por ejemplo: ajuste de reloj o programa con
temporizador). Presione para añadir o cancelar
números de canal durante preajuste de canal.
Botón STOP/EJECT (VCR)
●Botón de expulsión
Púlselo para sacar el videocasete de la
videograbadora.
● Botón Stop
EN
1L25
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
Presione detener el movimiento de la cinta.
Presione para entrar dígitos cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador). Presione para seleccionar los modos de
ajuste del menú en pantalla.
Botón OUTPUT
Presione para seleccionar el modo DVD o el modo VCR.
● Usted puede cambiar el modo de salida ya presionando
el Botón OUTPUT en el panel delantero o ya presionando el Botón DVD o VCR en el control remote. Sin
embargo, si usted presiona el Botón OUTPUT en el
panel delantero primero, usted necesita volver a
seleccionar el modo correspondiente presionando el
Botón DVD o el Botón VCR en el control remote.
Botón FWD/SKIP (DVD)
Reproduce desde el inicio del siguiente capítulo o pista.
Retenga abajo para avanzar rápidamente la reproducción.
Botón PLAY (DVD)
Comienza la reproducción del contenido del disco.
Botón SKIP/REV (DVD)
Reproduce desde el inicio del capítulo o pista actual.
Retenga abajo para reproducción inversa rápida.
Botón STOP (DVD)
Detiene la operación del disco.
Botón OPEN/CLOSE
Presione para insertar discos en o removerlos de la bandeja
de disco.
Ventanilla de Sensor Remoto, Visualización
Botón SPEED
Presiona para seleccionar la velocidad de grabación de
VCR (SP o SLP)
Botón POWER
Presione para conectar y desconectar la alimentación.
Botones numéricos
●Modo DVD
Presione para seleccionar directamente una Pista (CD de
Audio) para reproducción.
Presione para programar Pistas (Dcde Audio) para reproducir.
●Modo VCR
Presione para seleccionar canales de TV en el DVD/VCR.
Para seleccionar canales, entre números de canal como un
número de dos dígitos para los resultados más rápidos.
Por ejemplo, para seleccionar canal 6, presione 0.6.
Botón +100:
Si usted desea seleccionar canales 100 y arriba, presione
este Botón primero, luego presione los dos dígitos últimos. Por ejemplo, para seleccionar canal 125, presione
Botón “+100” primero, luego presione “2” y “5”.
Botón DISPLAY
●Modo DVD
Presione para tener acceso o remover la pantalla de visualización durante reproducción DVD o CD de audio.
●Modo VCR
Presione para tener acceso o remover visualización de
estado en pantalla de VCR.
Botón DVD
Presione antes de utilizar el control remote para funciones
DVD.
Botón h
●Modo DVD
Presione para ver la imagen DVD en movimiento de
inversión rápida o para invertir la reproducción de un
DC de Audio.
●Modo VCR
Presione para rebobinar la cinta o para ver la imagen rápidamente en inversión durante el modo de
reproducción.(Búsqueda en Rebobinado). Presione
para cancelar un ajuste de programa con temporizador. Presione para corregir dígitos cuando
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
– 43 –
ajuste programa. (Por ejemplo: ajuste de reloj o
programa con temporizador). Presione para añadir
o cancelar números de canal durante preajuste de
canal.
Botón Stop
Presione detener el movimiento de la cinta.
Presione para entrar dígitos cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador). Presione para seleccionar los modos de
ajuste del menú en pantalla.
Botón RECORD
Presione para iniciar una grabación. O, presione repetidamente para iniciar una grabación de Un-Toque.
Botón MENU
●Modo DVD
Presione para visualizar el menú del Disco.
●Modo VCR
Presione para tener acceso al menú VCR.
Botón TITLE
Botón SETUP
Presione para entrar el modo de preparación o para cambiar
elementos de preparación.
Botón ZOOM
Amplía parte de una imagen reproducida-DVD.
Botón MODE
Activa modo de reproducción de programa o reproducción
aleatoria cuando se reproducen CDs o MP3. Ajusta Nivel
de negro o TruSurround SRS.
Botón SUBTITLE
Presione para seleccionar un idioma de subtítulo deseado.
Botón ANGLE
Presione para cambiar el ángulo de cámara para ver la
secuencia que se está reproduciendo desde un ángulo diferente.
Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista
actual.
Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
Botón SEARCH MODE
●Modo DVD
Presione para tener acceso o remover la indicación de
búsqueda, que le permite ir directamente a un
Título/Capítulo/Pista/Tiempo especificado.
●Modo VCR
Presione para avanzar o rebobinar rápidamente la cinta a
una longitud específica de tiempo.
Botón CLEAR/C.RESET
●Modo DVD
Presione para reponen el ajuste.
●Modo VCR
Presione para reponer el contador. Presione para salir de
la pantalla MEMU.
Botón RETURN
Vuelve a la operación previa.
Botones de flecha
Utilice cuando haga ajustes mientras mira la indicación en
una pantalla de TV.
Botón ENTER
Presione para aceptar un ajuste.
Botón g
●Modo DVD
Presione para avanzar rápidamente el Disco. Presione el
Botón PAUSE, luego presione el Botón FWD iniciar a
reproducción en movimiento lento. Presione el Botón
FWD repetidamente para cambiar la velocidad de
avance del movimiento lento.
●Modo VCR
Presione para avanzar rápidamente la cinta o ver la
imagen rápidamente en avance durante reproducEN
1L25
50.
51.
52.
53.
ción. (Búsqueda en Avance). Cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con
temporizador), presione para determinar su selección y proceder al siguiente paso que usted desea
entrar. Presione para determinar los modos de
ajuste del menú en pantalla. Presione para añadir o
cancelar números de canal durante preajuste de
canal.
Botón PLAY
Presione para comenzar reproducción. Presione
para entrar dígitos cuando ajuste programa. (Por
ejemplo: ajuste reloj o programa con temporizador). Presione para seleccionar los modos de
ajuste del menú en pantalla.
Botón VCR
Presione antes de utilizar el control remote para funciones de VCR.
Botón PAUSE
●Modo DVD
Presione para pausar la reproducción de Disco. Presione
repetidamente para avanzar la imagen DVD paso a paso
(o un fotograma cada vez).
●Modo VCR
Mientras graba, presione para detener provisionalmente
la grabación (pausa). Presione por segunda vez para
reanudar la grabación normal. Usted no puede pausar
Grabación de Un-Toque. O, presione durante la reproducción de cinta para congelar la imagen.
Botón SLOW
Durante la reproducción de cinta, presione mirar la cinta de
videó a movimiento lento. Presione de nuevo para reanudar
la reproducción normal. Este Botón no afecta la reproduc-
VISIÓN TRASERA
ción DVD.
54. Botón VDR/TV
Utilice para seleccionar la posición VCR o TV. Si la Luz
VCR/TV aparece en la parte delantera del DVD/VCR, está
en la posición VCR (en cualquier modo VCR o DVD). Si
la Luz VCR/TV no aparece en la parte delantera del
DVD/VCR, está en la posición TV.
●Posición VCR
Cuando la Luz VCR OUTPUT verde aparece en la parte
delantera del DVD/VCR, utilice la VCR para mirar una cinta,
para mirar un programa de TV mientras lo graba o para mirar
una radiodifusión de TV utilizando los botones CHANNEL o
Numéricos para cambiar canales en la DVD/VCR.
Cuando la Luz DVD/VCR aparece en la parte delantera de la
DVD/VCR, utilice el DVD/VCR para mirar la reproducción
de Disco o menús.
●Posición de TV
Utilice para mirar TV (cambiando canales en el TV) o
para mirar un programa mientras graba otro.
55. Botones SKIP/CH
●Modo DVD
Presione para saltar Capítulos o Pistas.
●Modo VCR
Notas
¡Para utilizar el control remote para operar el DVD/VCR y
sus funciones, presione el Botón DVD en el control remote
antes de presionar otros botones DVD. Verifique que la
Luz DVD OUTPUT verde está encendida.
¡Para utilizar el control remote para operar la VCR y sus
funciones, presione el Botón VCR en el control remote
antes de presionar otros botones VCR. Verifique que la
Luz VCR OUTPUT verde está encendida.
57
58
IN
59
60
DVD/VCR
OUT
COMPONENT
VIDEO OUT
ANT - IN
L
DVD/VCR
AUDIO OUT
AUDO
R
L
VIDEO
R
ANT - OUT
CH3 CH4
67 66 65
64 63
Presione para cambiar canales de TV en la DVD/VCR.
56. Botón AUDIO
Presione para seleccionar un idioma de audio deseado o
modo de sonido.
57. Cordón de Alimentación AC
58.
59.
60.
61.
62.
Conecte a una toma de corriente AC estándar para suministrar corriente al DVD/VCR.
Tomas AUDIO IN
Conecte aquí los cables de audio procedentes de las
tomas de salida de audio de un camcorder, otra VCR o
una fuente de audio.
Tomas DVD/VCR AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas
de entrada de audio de un televisor u otro equipo de
audio.
Tomas COMPONENT VIDEO OUT
Conecte aquí los cables de videó componente
opcionales y a las tomas de entrada de Videó componente de un televisor.
Toma COAXIAL
Conecte aquí un cable de audio digital coaxial opcional
y a la toma de entrada Audio Digital Coaxial de un
descodificador o receptor de audio.
Toma S-VIDEO OUT
63.
64.
65.
66.
67.
Y
S-VIDEO DIGITAL AUDIO OUT
Cb OUT
PCM / BITSTREAM
COAXIAL
Cr
62 61
Conecte aquí un cable de S-Videó opcional y a la toma
de entrada de S-Videó de un televisor.
Toma DVD/VCR VIDEO OUT
Conecte aquí el cable de videó amarillo (provisto) y a la
toma de entrada de Videó de TV.
Toma VIDEO IN
Conecte un cable procedente de la toma de salida de
videó de un camcorder, otra VCR o una fuente de audiovisual (reproductor de disco láser, reproductor de disco
de videó, etc.) aquí.
Cambio CH3/CH4
Ajuste a canal 3 ó 4 para utilizar su TV con su
DVD/VCR.
Toma ANTI-IN (Entrada de Antena)
Conecte su antena o cable aquí.
Toma ANT-OUT (Salida de Antena)
Utilice el cable coaxial RF provisto para conectar esta
toma a la Toma ANTENNA IN en su TV.
Caja de cables o Sistema de Radiodifusión Directa.
Notas
¡La toma S-VIDEO OUT, toma COAXIAL, toma
OPTICAL y tomas COMPONENT VIDEO OUT
son sólo útiles en el modo DVD.
– 44 –
EN
1L25
CAMBIO DE VCR/DVD
Como este producto se utiliza del reproductor VCR y DVD, es necesario cambiar uno del
otro.
CAMBIO AL MODO VCR
CAMBIO AL MODO DVD
Presione el Botón VCR en el control remote.
(Verifique que la Luz VCR OUTPUT está enendida.)
Presione el Botón DVD en el control remote.
(Verifique que la Luz DVD OUTPUT está encendida)
O
O
Presione el Botón OUTPUT en el panel delantero y,
luego, presione el Botón VCR en el control remote.
(Verifique que la Luz VCR OUTPUT está encendida.)
Presione el Botón OUTPUT en el panel delantero y,
luego, presione el Botón DVD en el control remote.
(Verifique que la Luz DVD OUTPUT está encendida.)
Notas
¡Presionando sólo el Botón OUTPUT en el panel delantero no cambia el modo del control remote. Usted siempre necesita seleccionar el modo correcto en el control remote, también.
POWER
VIDEO
POWER SPEED
AUDIO
CHANNEL
DVD OPERATION
VCR OPERATION
TIMER
SET
VCR/TV
OPEN/CLOSE
STOP
SKIP/REV
PLAY
FWD/SKIP
STOP/EJECT REW
PLAY
F.FWD REC/OTR
CSR.IN
L
AUDIO
R
OUTPUT
1
2
3
4
5
6
7
8
9
0
+ 10
DVD
VCR
SKIP/CH.
VCR/TV
Luz DVD OUTPUT
Botón DVD
Luz VCR OUTPUT
Botón VCR
DVD OPERATION
+100
DISPLAY
SLOW
PAUSE
PLAY
VCR OPERATION
STOP
PLAY
FWD/SKIP
RECORD
STOP/EJECT REW
OUTPUT
MENU
ENTER
Botón OUTPUT
SETUP
TITLE
MODE
ZOOM
RETURN
SEARCH
MODE
SUBTITLE ANGLE REPEAT
– 45 –
CLEAR/
C.RESET
A-B
EN
1L25
CONEXIONES
DVD/VCR A CONEXIÓN DE TV
AJUSTANDO EL CONMUTADOR
CH3/CH4
1. Desconecte el cordón de alimentación AC del toma de
corriente AC.
2. Desconecte la antena o cable del TV.
3. Conecte la antena o cable a la toma ANT.IN del
DVD/VCR.
4. Conecte el DVD/VCR al TV utilizando el cable coaxial.
5. Enchufe los cordones de alimentación CA del
DVD/VCR y TV dentro de las tomas de corriente AC.
Si su TV no tiene terminales A/V:
Cuando el DVD/VCR está en modo de Reproducción
VCR o cuando el DVD/VCR está en el modo VCR. su
TV recibirá señales del DVD/VCR en cualquiera de
los canales 3 ó 4. Para utilizar el DVD/VCR con su TV,
ponga el conmutador selector en CH3 o CH4 (que está
ubicado en la parte trasera de su DVD/VCR),
cualquiera no se utilice para radiodifusiones normales
en su área. Luego, ajuste su TV al mismo canal.
CONECTANDO A UN TV
Por favor, vea la [Fig.1] en la página 14 para detalles.
CONECTADO A UN TV QUE TIENE TOMA DE ENTRADA DE SVÍDEO o TOMAS DE ENTRADA DE VÍDEO COMPONENTE
Por favor, vea la [Fig. 2] en la página 14 para detalles.
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE
ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT
Por favor, vea la [Fig. 4] en la página 15 para detalles.
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY O
DESCODIFICADOR DTS
Por favor, vea la [Fig. 5] en la página 16 para detalles.
CONECTANDO A UN AUDIO ANALÓGICO
Por favor vea la [Fig. 6] en la página 16 para detalles.
PREPARACIÓN
PREPARACIÓN DE CANAL AUTOMÁTICA
VCR
1 Conecte el TV y ponga el TV en el canal 3 ó 4.
4 Inicie canal preajustado presionando [F.FWD]
2 Conecte el DVD/VCR presionando [POWER].
una vez. El sintonizador explora y memoriza
todos los canales activos de su área.
Ambas Luces POWER y VCR/TV se encenderán.
5 Después de explorar, el sintonizador de
3 Seleccione el Idioma en la pantalla (“INGLÉS”,
detiene en el canal memorizado más bajo. La
pantalla de TV retorna al modo TV.
“FRANCÉS” o “ESPAÑOL”) presionando [PLAY] o
[STOP]. Luego, presione [F.FWD].
– 46 –
EN
1L25
REPRODUCCIÓN DE UN DISCO
PREPARACIÓN DE RELOJ
VCR
REPRODUCIENDO UN DVD,
VIDEO O UN CD AUDIO
Ajuste el reloj con precisión para grabación con temporizador automática adecuada. Le sugerimos que usted utilice
un TV o estación de radio como su fuente de tiempos.
1 Presione [MENU] dos veces para llamar el menú
principal. (Si usted ha ajustado ya el reloj, usted
sólo tiene que presionarlo una vez).
¡Si el reloj no está ajustado, aparece primero el menú
CLOCK SET. En este caso, siga el paso [3].
2 Seleccione “CLOCK SET” presionando [PLAY]o
[STOP]. Luego, presione [F.FWD]
3 Ajuste el reloj.
DVD
CD
Para empezar
Conecte la alimentación del TV, amplificador y
cualquier otro componente que se encuentre conectado
al DVD/VCR. (Cambie el sistema de entrada para que
se adapte DVD/VCR y compruebe que el volumen de
sonido sea correcto).
1 Presione el Botón POWER.
¡La alimentación se conectará.
Compruebe que la Luz DVD OUTPUT está encendida. Si no, presione el Botón DVD en el control
remote para cambiar el modo DVD/VCR.
1) Ajuste el mes
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
2 Presione el Botón OPEN/CLOSE.
¡La bandeja de carga del disco se abrirá.
2) Ajuste el día
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
3 Ponga un disco en la bandeja.
¡Asegúrese de que el disco está asentado correcta-
mente, con el lado de la etiqueta arriba.
3) Ajuste el año
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
El día de la semana aparecerá automáticamente.
4 Presione el Botón PLAY.
¡La bandeja se cerrará automáticamente, y la repro-
ducción empezará luego desde el primer capítulo o
pista del disco. Usted necesita presionar el Botón
PLAY sólo cuando la bandeja se ha cerrado presionando el Botón OPEN/CLOSE.
4) Ajuste la hora
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
5 Presione el Botón STOP para detener la
reproducción.
5) Ajuste el minuto
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
6) Ajuste el AM o PM
Presione [PLAY] o [STOP]
repetidamente.
AJUSTE DE RELOJ
MES DIA
AÑO
03 / 18 LUN 2002
HORA MINUTO AM/PM
05 : 40
PM AM
PM
¡Para retroceder un paso, presione [REW]
4 Ponga en marcha el reloj presionando
[CLEAR/C.RESET] o [F.FWD].
– 47 –
EN
1L25
LIMITED WARRANTY
FUNAI CORP. will repair this Emerson product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest Emerson Authorized Service Center or for general service procedure, please
call 1-800-256-2487 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-256-2487
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN03017
H9200UD ★★★★★