Owner’s Manual
Getting started
EWR10D4
Connections
DVD Recorder
Before you start
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
Recording
Playing discs
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
Supplied Accessory
• Owner’s Manual
(0VMN04178)
• Quick Use Guide
(0VMN04181)
Owner's Manual
Español
(You CANNOT record on any copyright protected DVD disc with this DVD recorder.)
Others
Before you use this unit, you need to complete connections.
Refer to “Connections” on pages 13-15.
To record a program easily, refer to “Easy DVD recording” on pages 16-17
after connections are completed.
Changing the SETUP menu
Please read before using this equipment.
If you need additional operating assistance after reading this owner’s manual or to
order replacement accessories, please call
TOLL FREE : 1-800-605-8457
or visit our web site at http://www.funai-corp.com
Editing
• Remote control
• RF cable
• Audio/Video cables
(WPZ0102TM015 or
(NB001UD)
(WPZ0901TM002 or
with two AA batteries WPZ0901CAB01)
WPZ0102LTE01)
Before you start
Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible
eye injury.
CAUTION:
CAUTION:
LOCATION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO
BEAM.
INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
For Customer Use:
Read carefully the information located at the back of this unit and enter below the Serial No.Retain this information for future
reference.
Model No. _____________________
Serial No. _____________________
2
Before you start
Important Safeguards
porting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig.A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
GROUND
CLAMP
Connections
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Recording
Playing discs
Editing
Changing the SETUP menu
Others
14. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits.When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension cords
as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind into
this product through any openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
18. Servicing - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service - Unplug this product from the wall
outlet and refer servicing to qualified service personnel under
the following conditions:
a.When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions.Adjust only those controls that are covered by
the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f.When the product exhibits a distinct change in performance this
indicates a need for service.
20. Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22. Heat - This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Getting started
Español
1. Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should
be followed.
5. Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION:A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility
of the loss of an authorization code for a CATV converter, is
not intended to be unplugged by the user for cleaning or any
other purpose, may exclude the reference to unplugging the
appliance in the cleaning description otherwise required in
item 5.
6.Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7.Water and Moisture- Do not use this product near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool, and the like.
8.Accessories - Do not place this product on an unstable cart,
stand, tripod, bracket, or table.The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the
appliance should follow the manufacturer's
instructions and should use a mounting
accessory recommended by the manufacturer. An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
9.Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and
to protect it from overheating, and these openings must not be
blocked or covered.The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult your
appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
11. Grounding or Polarization - This product is equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet
only one way.This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit
from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges.Article 810 of
the National Electrical Code,ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and sup-
Before you start
Precautions (cont’d)
3
Before you start
Precautions (cont’d)
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position. Do not
place anything directly on top of the unit. Do not place
the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat.Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper heat
dissipation. Do not block the ventilation holes on the
sides of the unit.Avoid locations subject to strong vibration or strong magnetic fields.
Maintenance
SERVICING
• Please refer to relevant topics on the Troubleshooting
Guide on pages 92-94 before return the product.
• When this unit become inoperative, do not try to correct
the problem by yourself.There are no user-serviceable
parts inside.Turn off, unplug the power plug, and please
call our help line mentioned on the front page to locate
an Authorized Service Center.
CLEANING THE CABINET
Avoid the Hazards of Electrical Shock
and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the
power cord immediately and take the unit to our
Authorized Service Center for servicing.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it
is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do
not use this unit at least for 2 hours until its inside gets
dry.
About Copyright
Unauthorized copying, broadcasting, public performance
and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Symbol in this owner's manual
Many functions of this DVD recorder are depending on
the disc type or the recording mode.
To specify for what disc type or recording mode each
function is, we put the following symbols at the beginning
of each item to operate.
Symbol
DVD-V
Video
DVD-RW
VR
4
Description
Available to DVD Video discs
Avaialble to DVD-RW in Video mode
DVD-RW
Avaialble to DVD-RW in VR mode
DVD-R
Available to DVD-R discs
CD
Available to Audio CDs
MP3
Available to CD-R/RW discs with
MP3 files
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasive.
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning
cloth.Wipe the disc from the center out. Do not wipe in
a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning
agents or antistatic spray intended for analogue records.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you
refer to the relevant sections and to “TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is
not used.
Before you start
Recording . . . . . . . . . . . . . . . . . . . . . . .26
Tour of the SETUP menu . . . .
Settings for Language . . . . . . .
Settings for Display . . . . . . . . .
Settings for Audio . . . . . . . . . .
Settings for Parental lock level
Others
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.83
.84
.86
.88
.90
Others . . . . . . . . . . . . . . . . . . . . . . . . .92
Troubleshooting
Language code .
Glossary . . . . . . .
Specifications . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.92
.95
.96
.97
Español . . . . . . . . . . . . . . . . . . . . . . . . .98
5
Español
Information on DVD play . . . . . . . . . . . . . . . . . .41
Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Playing discs using the disc menu . . . . . . . . . . . . . . .44
Playing discs using the title menu . . . . . . . . . . . . . . .45
Special playback . . . . . . . . . . . . . . . . . . . . . . . . .46
Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Fast forward / Fast reverse . . . . . . . . . . . . . . . . . . .46
Changing the SETUP menu . . . . . . . . .83
Changing the SETUP menu
Playing discs . . . . . . . . . . . . . . . . . . . . .41
Editing
Information on DVD recording . . . . . . . . . . . . . .26
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Restrictions on recording . . . . . . . . . . . . . . . . . . . .26
Information on copy control . . . . . . . . . . . . . . . . . .27
Making discs playable in other DVD player (Finalize) 27
Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . .28
Settings for the recording format to a blank disc . . .28
Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . . .30
Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . .31
Checking the recording picture quality . . . . . . . . . .32
One-touch timer recording . . . . . . . . . . . . . . . .33
Timer recording . . . . . . . . . . . . . . . . . . . . . . . . .34
Hints for timer recording . . . . . . . . . . . . . . . . . . . . .36
Settings for an external source . . . . . . . . . . . . . .37
Connection to an external source . . . . . . . . . . . . . .37
Recording from an external source . . . . . . . . . . . . .38
Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . .39
Setting a disc to protect . . . . . . . . . . . . . . . . . . .40
Playing discs
Information on disc editing . . . . . . . . . . . . . . . . .57
Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . . .57
Editing discs with Video mode . . . . . . . . . . . . . . . . .57
Editing discs with VR mode . . . . . . . . . . . . . . . . . . .58
Editing DVD-RW discs in Video mode . . . . . . . .59
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .60
Setting or clearing chapter markers . . . . . . . . . . . . .62
Editing DVD-RW discs in VR mode (Original) . .63
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .64
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .65
Setting or clearing chapter markers . . . . . . . . . . . . .67
Setting pictures for thumbnails . . . . . . . . . . . . . . . . .68
Setting titles to protect . . . . . . . . . . . . . . . . . . . . . .70
Releasing titles from protecting . . . . . . . . . . . . . . . .71
Editing DVD-RW discs in VR mode (Playlist) . . .72
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .73
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .74
Setting or clearing chapter markers . . . . . . . . . . . . .76
Setting pictures for thumbnails . . . . . . . . . . . . . . . . .77
Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . . .79
Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Editing DVD-R discs . . . . . . . . . . . . . . . . . . . . . .81
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Putting names on titles . . . . . . . . . . . . . . . . . . . . . .82
Recording
Editing . . . . . . . . . . . . . . . . . . . . . . . . .57
Easy DVD recording . . . . . . . . . . . . . . . . . . . . . .16
Channel setting . . . . . . . . . . . . . . . . . . . . . . . . . .18
Getting channels automatically . . . . . . . . . . . . . . . . .18
Adding/deleting channels . . . . . . . . . . . . . . . . . . . . .19
Selecting the TV stereo or SAP . . . . . . . . . . . . .20
Clock setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . .21
Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . . .22
Setting the daylight saving time . . . . . . . . . . . . . . . .24
Selecting the TV aspect ratio . . . . . . . . . . . . . . .25
Connections . . . . . . . . . . . . . . . . . . . . .13
Getting started
Getting started . . . . . . . . . . . . . . . . . . .16
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Functional overview . . . . . . . . . . . . . . . . . . . . . . .7
Installing batteries in the remote control . . . . . . . . . .9
Using a remote control . . . . . . . . . . . . . . . . . . . . . . .9
SETUP/DISC/CD menu . . . . . . . . . . . . . . . . . . . . . .10
DISPLAY menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connections
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . .13
Connection to a cable box or satellite box . . . .14
When connecting to a cable box or satellite box with
only a few scrambled channels . . . . . . . . . . . . . . . . .14
When connecting to a cable box or satellite box with
many scrambled channels . . . . . . . . . . . . . . . . . . . . .14
Connection to an Audio System . . . . . . . . . . . . .15
Skipping TV commercials during play . . . . . . . . . . . .47
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Step by step playback . . . . . . . . . . . . . . . . . . . . . . . .48
Slow forward / Slow reverse play . . . . . . . . . . . . . . .48
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . .50
Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Repeat/Random/Program playback . . . . . . . . . .52
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Random playback . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Selecting the format of audio and video . . . . . .54
Switching audio soundtrack . . . . . . . . . . . . . . . . . . .54
Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . . .55
Switching camera angles . . . . . . . . . . . . . . . . . . . . . .56
Reducing block noise . . . . . . . . . . . . . . . . . . . . . . . .56
Before you start . . . . . . . . . . . . . . . . . . .2
Before you start
Table of contents
Before you start
Features
Not only playing the discs of DVD or CD, but this DVD recorder features for you recording to DVD discs
and editing them after that.
Followings are what you can do with this DVD recorder.
Recording
This DVD recorder is compatible with both DVD-RW,
which is rewritable repeatedly, and DVD-R, which is available for recording once.You can choose either one for
your convenience.
Up to 8 program recording:
You can program the DVD recorder to record up to 8
programs, up to a year in advance. Daily or weekly program recordings are also available.
One-touch timer recording:
Easily you can set a recording time as you prefer. Every
time the REC button pressed during recording, the
recording time will be increased by 30 minutes up to 4
hours.The recording automatically stops when the recording time you set is reached.
REC MONITOR:
You can confirm the picture quality for recording in the
current recording speed which you set. If you want to
change the recording speed, press REC SPEED button to
set the desired recording mode.
Automatic Chapter marker setting:
Chapter markers will be put on recordings as you set in
SETUP menu before attempting to record.
Automatic Title menu making:
The DVD recorder makes title menus automatically when
finalizing the disc which are recorded in Video mode.
Automatic PLAYLIST making (VR mode):
A Playlist will be prepared from an Original list, so that
you can edit titles in a Playlist as you prefer.
An Original list is kept as it is.
Editing
Setting/Clearing chapter markers:
You can easily add chapter markers anywhere in your
recordings for easy editing. (VR mode)
Making your own Playlist:
With the original remains as it is, you can edit titles on
Playlist variously as you prefer.
Putting names on titles
Setting pictures for thumbnails
Setting/clearing chapter markers
Deleting parts of titles etc
Protecting titles:
To avoid erasing titles, the protect function is useful when
it is ON in the original list.
Compatibility
Available for playing discs recorded with Video
mode on a regular DVD player (Video mode):
Discs recorded with the Video mode can be played on
regular DVD players, including computer DVD drives compatible with DVD-Video playback*.You will need to finalize
the discs recorded in Video mode to play in other DVD
players.
* DVD-Video Format (Video mode) is a new format for recording on DVD-R/RW discs that was approved by the DVD Forum
in 2000. Adoption of this format is optional for manufactures of
DVD playback devices, and there are DVD-Video players, DVDROM drives or other DVD playback devices that do not play
DVD-R/RW discs recorded in the DVD-Video Format.
Play
Theater surround sound in your home:
When connecting the DVD recorder to an amplifier or a
decorder which is compatible with Dolby Digital, you are
allowed to experience the theater surround sound from
discs with surround sound system.
Quick search for what you want to watch:
You can easily find the part you want to watch using
search function. Search for a desired point on a disc by
title, chapter, or time.
Start to play from Original and Playlist:
Title playing is available from either an Original list or
Playlist.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
6
Before you start
Before you start
Functional overview
Front Panel
1
2 345 6
REV
7
FWD
8
9
OPEN / CLOSE
REC SPEED
S-VIDEO
VIDEO
L
AUDIO
R
1.
POWER button
Press to turn the DVD recorder on and off.
2.
3.
4.
6.
7.
Rear Panel
11.
12.
13.
14.
15.
1
2
1.
3.
4.
6.
7
7.
TV ANTENNA OUT jack
Use to connect an antenna cable to pass the signal
from the TV ANTENNA IN to your TV monitor.
8. S-VIDEO INPUT jack(LINE1)
Use to connect the S-Video output of external equipment with an S-Video cable.
9. VIDEO INPUT jack(LINE1)
Use to connect external equipment with a standard
video cable.
10. AUDIO INPUT jacks(LINE1)
Use to connect external equipment with standard
audio cables.
11. COAXIAL DIGITAL AUDIO OUTPUT jack
Use to connect an AV receiver, Dolby Digital
decorder or other equipment with a coaxial digital
input with a digital coaxial cable.
Others
5.
8
6
Changing the SETUP menu
2.
AC Power Cord
Connect to a standard AC outlet to supply power to this
unit.
AUDIO OUTPUT jacks 1, 2
Use to connect a TV monitor, AV receiver or other
equipment with standard audio cables.
VIDEO OUTPUT jack
Use to connect a TV monitor, AV receiver or other
equipment with a standard video cable.
S-VIDEO OUTPUT jack
Use to connect the S-Video input of a TV monitor, AV
receiver or other equipment with an S-Video cable.
COMPONENT VIDEO OUTPUT jacks
Use to connect a TV monitor with component video
inputs with component video cables.
TV ANTENNA IN jack
Use to connect an antenna.
10 9
5
Editing
11
3 4
Playing discs
8.
10.
Display
Refer to “Guide to Displays on the front panel” on
page 12.
Remote control sensor
Receive signals from your remote control so that you
can control the DVD recorder from a distance.
REC SPEED button
Press to switch the recording speed.
REC button
Press to start recording.
AUDIO INPUT jacks (LINE2)
Use to connect external equipment with standard
audio cables.
VIDEO INPUT jack (LINE2)
Use to connect external equipment with a standard
video cable.
S-VIDEO INPUT jack (LINE2)
Use to connect the S-Video output of external equipment with an S-Video cable.
Recording
5.
STOP C button
Press to stop play or recording.
REV H button
Press to skip to the previous chapter or track.
Press and hold for 1.5 seconds to fast reverse.
PLAY B button
Press to start or resume play.
FWD G button
Press to skip to the next chapter or track.
Press and hold for 1.5 seconds to fast forward.
CH L / K button
Press to change the channel up and down.
OPEN/CLOSE A button
Press to open or close the disc tray.
Disc tray
Place a disc when open.
9.
Getting started
If timer programmings have been set, press to
set the unit in timer-standby mode.
10
Connections
15 14 13 12 11
Note
Español
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to
the DVD recorder.
• This unit does not have the RF modulator.
7
Before you start
Functional overview (cont’d)
Remote Control
POWER
2
1
3
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
A
CH
REC
MONITOR
4
REC SPEED CLEAR
6
8
5
REC
PAUSE
7
H
19
G
20
B
FWD
h
g
21
STOP
C
SETUP
TOP MENU
MENU/LIST
12
14
18
PLAY
REV
11
13
16
17
SKIP
F
9
10
OPEN/CLOSE
DISPLAY
22
K
ENTER
REPEAT
{
B
23
RETURN
ZOOM
15
1. POWER button
Press to turn the DVD
recorder on and off.
If timer programmings have
been set, press to set the unit
in timer-standby mode.
2. DISPLAY button
Press to display or change the
on-screen display.
3. CH K / L buttons
Press to change the channel
up and down.
4. REC MONITOR button
Press to check the video to be
recorded before attempting.
5. REC SPEED button
Press to switch the recording
speed.
6. CLEAR button
Press to clear the password
once entered or to cancel the
programming for CD or to
clear the selecting marker number in the marker setup mode
8 or to clear the program once
24
L
7.
8.
9.
10.
11.
12.
13.
25
entered in the timer recording
setting mode,etc.
REC button
Press to start recording.
PAUSE F button
Press to pause play or
recording.
PLAY B button
Press to start or resume play.
REV E button
During playback, press to play
fast reverse.
Or during playback is paused,
press to play slow reverse.
STOP C button
Press to stop play or recording.
SETUP button
Press to display the setup
menu.
TOP MENU button
Press to display the top
menu.
14. REPEAT button
Press to display the repeat
setting menu.
15. ZOOM button
Press to enlarge the picture
on the screen.
16. OPEN/CLOSE A button
Press to open or close the
disc tray.
17. TIMER PROG. button
Press to display the timer
program setting menu.
18. Number buttons
Press to select channel numbers.
Press to select a title/chapter/track on display or a TV
channel.
Or press to enter values for
the settings in the SETUP
menu.
19. CM SKIP button
During playback, press to skip
the 30 seconds.
20. SKIP H button
During playback, press to skip to
the previous chapter or track. Or
during play is paused, press to play
reverse step by step.
SKIP G button
During playback, press to skip to
the next chapter or track.
Or during playback is paused,
press to play forward step by step.
21. FWD D button
During playback, press to play
fast forward.
Or during playback is paused,
press to play slow forward.
22. MENU/LIST button
Press to display the Disc
menu.
To change ORIGINAL and
PLAYLIST on the TV screen.
(VR mode only)
23. ENTER button
Press to confirm or select
menu items.
24. K / L / B / { buttons
Press to select items or settings.
25. RETURN
button
Press to return to the previously displayed menu screen.
Before you start
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor on the
DVD recorder.
• Use within the operating range and angle as
shown.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the
remote sensor of the DVD recorder.
• Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the DVD
recorder.
• Replace the batteries when you notice a fall off in
the operating range of the remote control.
1
2
60˚
Playing discs
3
Within about
23feet (7m)
POW
ER
DISPL
AY
CH
4
GHI
1
.@/:
E
2
DEF
5
MNO
8
k
h
REV
CM
TIME
PRO
G. R
ABC
JKL
TUV
SPAC
E
0
3
WXY 6
Z
SK
H
9
SKIP
A
PQRS
CLEA 7
R
E
LOS
D
N/C
SPEE
PAUS
PLA
B Y
IP
P
OPE
REC
REC
C OR
RENIT
MO
P
U/
MEN AL
GIN
STOC
G
TOP
ORI
g
K
PLA
R
NU
LIS
ME Y
ENTE
D
FW
T
Remote
control
Recording
Install two AA batteries (supplied) matching the
polarity indicated inside battery compartment of the
remote control.
Getting started
Using a remote control
Connections
Installing batteries in the remote control
Before you start
Functional overview (cont’d)
Editing
Note:
Incorrect use of batteries can result in hazards such
as leakage and bursting. Please observe the following:
• Do not mix new and old batteries together.
• Do not use different kinds of battery together,
although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of each
battery match the indications in the battery compartment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction's rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or disassemble batteries.
Changing the SETUP menu
Others
Español
9
Before you start
Functional overview (cont’d)
Guide to Displays on screen menu
The DVD recorder uses the following types of display for most operations. SETUP/DISC/CD menu,Title list,
and DISPLAY, which allows you to change the playing status of disc during play. DISPLAY also gives you some
disc information for checking the status of the disc.
SETUP/DISC/CD menu
Press SETUP button to display the setup main menu, then choose either of SETUP/DISC/CD by K / L / { / B
button.Then, press ENTER button to display each menu.
These provides entries to all main functions of the DVD recorder.
“DISC” is available only when a DVD-R/RW disc is
inserted into the DVD recorder. When playing back
a DVD-Video disc (commercially available) or the
finalized DVD-R disc, you cannot select “DISC”.
“SETUP” is available only in the
Stop mode.
Setup Menu
1
2
3
Disc
CD Playback Mode
Edit
Random Play
Format
Program Play
Finalize
Disc Protect OFF
4
CD Playback Mode
Disc Setting
Setup
5
6
“CD” is available only when an
Audio CD disc is inserted into
the DVD recorder.
ON
1 2 3 4
1 2
Playback Setting
1. Playback:
To set up the DVD recorder to
play discs as you prefer.
2. Recording:
To set up the DVD recorder to
record to discs as you prefer.
3. Display:
To set up the OSD screen and the
front display of the DVD recorder
as you prefer.
4. Select Video:
To choose a line input to record
to DVD discs from other video
equipment.
5. Clock:
To set up the clock of the DVD
recorder as you need.
6. Channel:
To make the channel setting of
the DVD recorder as you
prefer.
10
1. Edit:
Turns on a title list, (When a disc
with VR mode is inserted,
'Original' or 'PlayList' is available.),
which shows the recorded titles
on the disc.
2. Format:
Allows you to erase all of the
recorded content on the disc.
The disc will be completely blank.
3. Finalize:
Allows you to finalize a disc
recorded titles.
4. Disc Protect (VR mode
only) :
Allows you to protect a disc from
accidental editing.
1. Random Play:
To set the random play programming.
2. Program Play:
To set the program playing.
Before you start
Before you start
Functional overview (cont’d)
DISPLAY menu
3
1
: Audio
: Subtitle
: Angle (except VR mode)
: Repeat
: Marker
Getting started
Details are on page 41.
: Search
: Noise Reduction
: Zoom
1
1
00:00:00
DVD-RW
Video mode
SP 1:25 Rem.
4
Connections
Press DISPLAY button to call up
the display menu.This menu will
give you the information on the
playing disc. Some operations are
available while disc is playing.
1. Indicates a disc type and a
format mode.
2. Indicates a recording mode
and possible recording time.
3. Indicates a title number, chapter number, and the time
lapse of disc play.
4. Each icon means:
2
Recording
Playing discs
Editing
Changing the SETUP menu
Others
Español
11
Before you start
Functional overview (cont’d)
Guide to Displays on the front panel
4
2
1
3
6
5
1. Current status of the
DVD recorder
2. Disc type
: Appears when an audio
CD or a disc with MP3
files is inserted in the disc
tray.
: Appears when a disc play
is paused.
: Appears during playing a
disc.
: Appears when a DVD
disc is inserted in the
disc tray.
: Appears when the timer
programming has been
set and is proceeding.
:
Appears when a DVD-R
disc is inserted in the
disc tray.
: Appears during recording
is in process.
:
Appears during repeat
play.
:
Appears when a DVDRW disc is inserted in
the disc tray.
3. Recording speed
Indicates the recording speed of
the disc.
4. Title/Track and Chapter
mark
: Appears when indicating
a title/track number.
: Appears when indicating
a chapter number.
5. Displays the following
• Playing time / remaining time
• Current title / chapter / track
number
• Recording time
• Clock
• Channel number
• OTR remaining time
6.
: Appears in the afternoon with the clock
displaying.
Display message
1
2
4
5
1. Appears when the DVD
recorder is powered on.
2. Appears when the DVD
recorder is powered off.
3. Appears when the disc tray is
opening.
3
6
4. Appears when the disc tray is
closing or close.
5. Appears when a disc is loading in the disc tray.
6. Appears when recording data
is writing on to the disc.
12
Connections
Antenna
Antenna
Cable
Signal
Cable
Signal
(Back of TV)
AUDIO IN
VIDEO
or
5
or
4
Connect
Video
Cable
(supplied)
3
Connect
RF Cable
(supplied)
Getting started
Connect
Audio
Cable
(supplied)
Connections
(Back of TV)
2
1
Connect
Disconnect
Before you start
Connection to a TV
(Back of DVD recorder)
Recording
6 Plug in the AC power cord of the DVD recorder.
Make one of the following connections, depending on the capabilities of your existing equipment.
Method 2
Better picture
Best picture
Playing discs
Basic Audio
Method 1
COMPONENT
VIDEO IN
TV
Y
AUDIO IN
R
S-VIDEO IN
L
CB
Editing
CR
Component
Video cables
(commercially
available)
Changing the SETUP menu
S-Video
cable
(commercially
available)
Audio cable
(supplied)
DVD Recorder
or
S-VIDEO OUT
COMPONENT VIDEO OUT
Others
AUDIO OUT
Note
13
Español
• Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy
protection system.
Connections
Connection to a cable box or satellite box
A
When connecting to a cable box or satellite box with only a few scrambled
channels
If you are using a cable box or satellite box with only a few scrambled channels, follow the setup on this
page. If many or all the channels are scrambled, we recommend using the setup on the following page.
With this setup:
• You can record any unscrambled channel by selecting the channel on the DVD recorder.
• You cannot record scrambled channels that require a cable box or satellite box.
(Cable box or
Satellite box)
(Back of TV)
AUDIO IN
VIDEO
OUT
IN
RF cable
5
3
4
Connect
Audio
cable
(supplied)
Connect
Video
cable
(supplied)
RF cable
(supplied)
2
Connect
Connect
Cable
Signal
RF cable
1
Connect
(Back of DVD recorder)
B
When connecting to a cable box or satellite box with many scrambled
channels
If many or all the channels you receive by cable or satellite are scrambled, we recommend using this setup.
With this setup:
• You can record any unscrambled channel by selecting the channel on the cable box or satellite box. Be sure
that the cable box or satellite box is turned on.
• You cannot record one channel while watching another channel.
(Back of TV)
AUDIO IN
4
Connect
Audio
cable
(supplied)
VIDEO
3
Connect
Video
cable
(supplied)
2
Connect
RF cable
(supplied)
(Cable box or
Satellite box)
OUT
Cable
Signal
IN
1 RF cable
Connect
(Back of DVD recorder)
Note to the Cable TV System Installer :
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the
National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the
cable ground shall be connected to the grounding system of the building, as close to the point of cable
entry as possible.
14
Connections
Before you start
Connection to an Audio System
• When you change the connections, all devices should be turned off.
• Refer to each owner’s manual for further information on other devices.
Method 1
Method 2
Stereo system
Dolby Digital decoder,
MD deck or DAT deck
AUDIO
COAXIAL
Connections
Analog audio
input jacks
Digital audio
input jack
Getting started
Audio Coaxial
Digital cable
(commercially
available)
Audio cable
(supplied)
DVD Recorder
DIGITAL
AUDIO OUT
AUDIO OUT
or
Recording
Playing discs
Editing
Note
• If output is Dolby Digital encoded audio, connect to a
Dolby Digital decoder, and set “Dolby Digital” to
“Stream” for the “Digital Out” setting in the SETUP
menu. (Refer to pages 88-89.)
• The audio source on a disc in a Dolby Digital 5.1 channel
surround format cannot be recorded as digital sound by
an MD or DAT deck.
• Unless connected to a Dolby Digital decoder, set “Dolby
Digital” to “PCM” for the “Digital Out” setting in the
SETUP menu. Playing a DVD using incorrect settings may
generate noise distortion, and may also damage the speakers. (Refer to pages 88-89.)
• Set “Dolby Digital” to “PCM” for the “Digital Out” setting in the SETUP menu for connecting to an MD deck
or DAT deck. (Refer to pages 88-89.)
• By hooking this unit up to a Multi-channel Dolby Digital
decoder, you can enjoy high-quality Dolby Digital 5.1
channel surround sound as heard in the movie theaters.
Changing the SETUP menu
Others
Español
15
Getting started
Easy DVD recording
The followings will help you to understand easily how to record to DVD discs.
Note:
Make sure batteries are in the remote control and you have connected this unit and the TV correctly.
Step 1: Choose a disc type
Step 2: Insert a blank disc
Remote Control
There are several types of DVD disc recordable
to choose from. Choose an applicable type by
“DVD disc types” on this page.
This DVD recorder can record on the following
type of discs.
POWER
DISPLAY
TIMER
PROG.
OPEN/CLOSE
1
CH
2
To open
A
.@/:
1
ABC
2
DEF
3
GHI
JKL
MNO
To turn on
For example, when you want to record repeatedly on the same disc, or when you want to edit the
disc after recording, select the rewritable DVDRW type disc.
POWER
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
JKL
MNO
A
CH
When you want to save recordings without any
alteration, a non-rewritable DVD-R can be your
choice.
3
To Close
Loading
This operation may take a
while to be recognized.
DVD disc types
.
: Most suitable.
: Can be used.
Format the disc
: Some functions are limited.
You want to
DVD-RW VR
: Cannot be used.
DVD-RW Video
DVD-R
DVD-RW Video
DVD-R
Record TV programs
Reuse by deleting unwanted contents
Edit recorded contents
Edit/Record from connected equipment
Copy discs for distribution
*1
Play on other DVD equipment
*1
Features
DVD-RW VR
Recording
Rewritable?
Yes
Yes
No
Can create chapters at fixed intervals (auto.)
Yes
Yes
Yes
Can create chapters wherever you like (manual)
Yes
No
No
Can record 16:9 size pictures
Yes
Yes
Yes
Can record Copy-Once programs
Yes
No
No
Can perform basic edit functions
Yes
Yes
No
Can perform advanced edit functions (Playlist edit)
Yes
No
No
Editing
*1
16
DVD-RW (VR mode) can only be played on DVD
equipment that is VR compatible.
Note:
For details of the above functions and implied
restrictions, see the explanations inside the manual.
Insert the disc in the
recorder.Then, format the
disc from SETUP menu.Video
format (Video mode) or
Video recording format (VR
mode) will be available
depending on the disc type
inserted.This is necessary to
prepare the disc for recording. Details are on pages 2830.
Getting started
POWER
DISPLAY
TIMER
PROG.
Step 4: Select the
desired
channel
POWER
OPEN/CLOSE
DISPLAY
TIMER
PROG.
CH
REC
MONITOR
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
TUV
8
WXYZ
9
SPACE
0
CM SKIP
OPEN/CLOSE
DISPLAY
TIMER
PROG.
CH
REC
MONITOR
.@/:
1
ABC
2
DEF
3
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
GHI
4
JKL
5
MNO
6
PQRS
7
REC SPEED CLEAR
TUV
8
WXYZ
9
SPACE
0
CM SKIP
CH
REC
MONITOR
REC
REC
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
Getting started
PQRS
7
REC SPEED CLEAR
POWER
OPEN/CLOSE
A
A
.@/:
1
Step 5: Record to
DVD discs
Connections
Step 3: Select the
recording
speed
SKIP
F
H
G
CH 1
SP 2:01 Rem.
Before you start
Easy DVD recording (Cont’d)
Recording
I
Hint 1: Play the recorded contents
Playing discs
You can select the title you want to play from a displayed menu, and immediately start to play. Recorded contents are very accessible on a disc, the procedure is simple really as you choose a
title on a chapter from the menu
Start Rec.
Stop/Start
Stop Rec.
screen.
Step 6: Stop the
record
What is titles and chapters?
Title 1
Title 2
7
REC SPEED CLEAR
REC
8
9
SPACE
0
CM SKIP
PAUSE
Editing
The contents of DVD disc are generally
divided into some titles.Titles may be
further subdivided into chapters.
SKIP
F
H
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
Changing the SETUP menu
Hint 2: Edit the recorded disc
You will find editing discs very easy, and the DVD recorder offers convenient
edit functions, which are possible only with DVD-R/RW discs.
You can edit the followings from a title list.
• Putting names on titles
• Setting pictures for thumbnails (VR mode)
• Setting/clearing chapter markers
• Deleting parts of titles (VR mode)
58%
Writing to Disc
Others
Original and Playlist (VR mode)
You can edit the recordings in Playlist without changing the original recordings. Any Playlist does not take up much disc space.
What “Original” or “Playlist” refers for?
Español
Throughout this manual, you will find Original and Playlist to refer to the actual
content and the edited version.
• Original content refers to what’s actually recorded on the disc.
• Playlist content refers to the edited version of the disc; how the Original
content is to be played.
This operation may
take a while to be
completed.
17
Getting started
Channel setting
All channels are stored in the
DVD recorder when purchased.
We recommend that you get
available channels in your area
stored using “Auto Preset” in the
Channel Preset of the SETUP
menu.
4
POWER
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
1
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
A
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
TUV
8
WXYZ
9
SPACE
0
CM SKIP
Setup
REC
DEF
3
PQRS
7
REC SPEED CLEAR
Getting channels automatically
OPEN/CLOSE
PAUSE
SKIP
F
H
G
B
PLAY
REV
1
g
STOP
C
Press POWER button to turn
on the DVD recorder.
3
7
Playback Setting
2
5
Turn the TV on and be sure
to select the input to which
the DVD recorder is connected.
Select “Channel” using K / L
/ { / B buttons, then press
ENTER button.
Channel Preset menu will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
Stereo
6
3
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Select “Auto Preset” using K
/ L buttons, then press
ENTER button.
The DVD recorder will start getting channels available in your
area.
CH 18
Auto Presetting Now
Setup Menu
7
Press SETUP button to exit.
•You can select only the channels
memorized in this unit by using
the CHANNEL buttons.
18
FWD
h
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
4
5
6
To select a channel
You can select a channel by
directly entering channel using
the Number buttons on the
remote control.
Notes for using the
Number buttons:
• When selecting cable channels
which are higher than 99,
enter channel numbers as a
three-digit number.(For example: 117, press 1,1,7)
• You must precede single-digit
channel numbers with a zero
(For example: 02, 03, 04 and
so on).
• You can select the line input
mode (“L1” or “L2”). To select
“L1” by pressing [0], [0], [1].To
select “L2” by pressing [0], [0],
[2]. Details are on page 38.
Note
• If the auto presetting is cancelled during presetting, some
channels not yet preset may
not be received.
• The selection will depend on
how you receive the TV channels.
To cancel the auto presetting during scanning:
Press RETURN button or
SETUP button to cancel.
Getting started
Before you start
Channel setting (cont’d)
Adding/deleting channels
Select “Manual Preset” using
K / L buttons, then press
ENTER button.
Manual Preset menu will appear.
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
Setup > Channel Preset > Manual Preset
1
SKIP
F
H
G
B
PLAY
FWD
h
g
STOP
C
1
7
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
5
6
Playing discs
Setup > Channel Preset > Manual Preset
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
Recording
Select the channel number to
add or delete.
Press { button to move to a
lower channel number.
Press B button to move to a
higher channel number.
2
PAUSE
REV
5
Setup Menu
REC
WXYZ
9
CM SKIP
Getting started
CH2
Add
Delete
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
OPEN/CLOSE
DISPLAY
Connections
The channels you no longer
receive or seldom watch can be
deleted from the memory.You also
may add channels into memory.
4
CH18
Add
Delete
Setup
Editing
6
Playback Setting
Select “Channel” using K / L
/ { / B buttons, then press
ENTER button.
Channel Preset menu will appear.
Others
7
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
Changing the SETUP menu
3
Select “Add” or “Delete”
using K / L buttons, then
press ENTER button.
The channel number will be
added or deleted from a channel
memory.Then a next channel
number will appear so that you
can continue adding or deleting
channels.
Stereo
Press SETUP button to exit.
Español
19
Getting started
Selecting the TV stereo or SAP
You can select a sound channel to
output from TV. “Stereo” has
been selected as the default.
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
4
Select “TV Audio Select”
using K / L buttons, then
press ENTER button.
Option window will appear.
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
Setup > Channel Preset
Auto Preset
Stereo
Stereo
SAP
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Manual Preset
TV Audio Select
OPEN/CLOSE
DISPLAY
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
5
Setup Menu
Select “Stereo” or “SAP”
using K / L buttons, then
press ENTER button.
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
Setup
6
Playback Setting
Press SETUP button to exit.
3
Select “Channel Preset”
using K / L / { / B buttons,
then press ENTER button.
Channel Preset menu will appear.
Setup > Channel Preset
Auto Preset
Manual Preset
TV Audio Select
20
Stereo:
Outputs main-audio.
SAP:
(Secondary Audio Program)
Outputs Sub-audio.
Refer to the item in “Glossary”
on page 96 for more information.
Stereo
1
6
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
5
Getting started
Before you start
Clock setting
Auto Clock Setting
4
Select “Auto Clock Setting”
using K / L buttons, then
press ENTER button.
Option window will appear.
POWER
7
REC
MONITOR
Setup > Clock
Clock Setting
Auto Clock Setting
Daylight Saving Time
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
OFF
Auto
Auto
Manual
Off
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
1
6
1
5
• If you do not know your
PBS channel number, select
“Auto” using K / L buttons,
then press ENTER button.
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
5
Setup Menu
Playing discs
• If you know your PBS channel number, select “Manual”
using K / L buttons, then
press ENTER button.
Setup > Clock
Clock Setting
2
Auto Clock Setting
Daylight Saving Time
OFF
Set Channel
No.
Auto
Auto
CH1
Manual
Off
Editing
Select SETUP using { / B buttons, then press ENTER button.
SETUP menu will appear.
Setup
6
Select “Clock” using K / L / { / B
buttons, then press ENTER button.
Clock menu will appear.
7
Setup > Clock
Clock Setting
Auto Clock Setting
Auto
Daylight Saving Time
ON
21
Español
Press POWER button to turn
off the DVD recorder. This unit
will search for the time only
when the power is off. Leave it off
for several minutes to give this
unit time to set the clock on the
front display of the front panel.
Note
• The clock may set itself automatically after you connect the
antenna/cable signal to this
unit and plug in the power
cord. In this case, the current
time will appear on the front
display on the front panel.
• The current time is not displayed or the displayed clock
is not correct, set the clock
manually.
Others
3
Press SETUP button to exit.
Changing the SETUP menu
Enter your PBS channel
number using Number or K
/ L buttons, then press
ENTER button.
Playback Setting
Recording
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
SETUP
Getting started
Make sure
• The antenna/Cable TV connections are correct.
• If this unit is connected to a
Cable Box or Satellite Box, select
the local PBS station on them to
set the clock automatically.
OPEN/CLOSE
DISPLAY
Connections
Set the clock before you try the
timer recording. If a Public
Broadcasting Station (PBS) is available
in your area, follow Auto Clock
Setting below. If not, follow Manual
Clock Setting on pages 22-23.
Getting started
Clock setting (cont’d)
Manual Clock Setting
4
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Select “Clock Setting” using
K / L buttons, then press
ENTER button.
A clock setting window will
appear.
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
Setup > Clock
Clock Setting
Auto
Daylight Saving Time
ON
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Auto Clock Setting
OPEN/CLOSE
DISPLAY
PAUSE
SKIP
F
---/--/----(---)
--:--
H
G
B
PLAY
REV
FWD
h
g
STOP
C
1
Setup Menu
Press ENTER button again.
Default date will appear.
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
Setup
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
5
Enter the date (month / day /
year) using K / L buttons.
Press { / B button to move the
cursor.
2
3
4
5
6
Setup > Clock
Clock Setting
Auto Clock Setting
Auto
Daylight Saving Time
ON
JAN / 12 / 2004 (MON)
12 : 00AM
Playback Setting
3
Select “Clock” using K / L /
{ / B buttons, then press
ENTER button.
Clock menu will appear.
Setup > Clock
6
Enter the time (hour /
minute) using K / L buttons,
then press { / B buttons.
A cursor will move on AM or PM.
Clock Setting
Auto Clock Setting
Auto
Daylight Saving Time
ON
Setup > Clock
Clock Setting
Auto Clock Setting
Auto
Daylight Saving Time
ON
JAN / 12 / 2004 (MON)
09 : 24 AM
Note
• Your clock setting will be lost if
either there is a power failure
or this unit has been unplugged
for more than 30 seconds
when you set the clock manually.
22
Getting started
Before you start
Clock setting (cont’d)
8
Press K / L buttons to select
AM or PM, then press ENTER
button.
Clock menu will appear, then the
settings will be activated.
Press SETUP button to exit.
Although seconds are not displayed,
they begin counting from zero.
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
Setup > Clock
Clock Setting
ON
REC
WXYZ
9
CM SKIP
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
8
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
7
Getting started
Auto
Daylight Saving Time
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
Auto Clock Setting
OPEN/CLOSE
DISPLAY
Connections
7
RETURN
ZOOM
L
Recording
Playing discs
When “Auto Clock Setting” is selected to “Auto” or
“Manual”, change it to “OFF” as following steps.
Repeat steps (1) to (3) in “Manual Clock Setting”.
Editing
B
PLAY
5
Select “Auto Clock Setting”
using K / L buttons, then
press ENTER button.
Option window will appear.
Select “OFF” using K / L
buttons, then press ENTER
button.
Clock Setting
Auto Clock Setting
Daylight Saving Time
OFF
Auto
Auto
Manual
Off
g
STOP
C
6
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
6
Setup > Clock
FWD
h
Press SETUP button to exit.
4
5
Changing the SETUP menu
4
REV
Others
Español
23
Getting started
Clock setting (cont’d)
Setting the daylight saving time
When Daylight Saving Time is
ON, the DVD recorder clock will
automatically move forward one
hour on the first Sunday in April
and move back one hour on the
last Sunday in October.
4
Select “Daylight Saving
Time” using K / L buttons,
then press ENTER button.
Daylight Saving Time options will
appear.
Setup > Clock
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
Auto Clock Setting
CH
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Clock” using K / L /
{ / B buttons, then press
ENTER button.
Clock menu will appear.
Setup > Clock
Clock Setting
Auto Clock Setting
Auto
Daylight Saving Time
ON
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
PAUSE
SKIP
F
H
ON
OFF
G
B
PLAY
REV
FWD
h
g
STOP
C
Select “ON” or “OFF” using
K / L buttons, then press
ENTER button.
Choose “ON” when currently
observing the daylight saving time.
2
REC
Auto
5
Setup Menu
TIMER
PROG.
REC SPEED CLEAR
Clock Setting
Daylight Saving Time
OPEN/CLOSE
DISPLAY
A
REC
MONITOR
1
24
POWER
6
Press SETUP button to exit.
1
6
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
5
Getting started
Before you start
Selecting the TV aspect ratio
Playback menu will appear.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
4:3 Letter Box
All
English
POWER
Digital Out
ON
Fast Forward with Audio
OFF
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
Original
OFF
Dynamic Range Control
CH
REC
MONITOR
1
REC
Setup > Playback
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
B
C
1
6
OFF
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
5
Refer to the Note on this
page.
Playing discs
Setup
ON
g
STOP
Original
OFF
Fast Forward with Audio
FWD
h
16:9 Box
Wide
4:3 Letter
8 & Scan
4:3 Pan
16:9English
Wide
Dynamic Range Control
G
PLAY
REV
Digital Out
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
SKIP
H
5
Editing
Select a desired option using
K / L buttons, then press
ENTER button.
6
Playback Setting
Recording
TV Aspect
2
PAUSE
F
Select “TV Aspect” using K /
L buttons, then press ENTER
button.
Option window will appear.
Setup Menu
WXYZ
9
CM SKIP
Getting started
4
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
OPEN/CLOSE
DISPLAY
Connections
You can select the TV aspect ratio
to match the formats of what you
are playing with the DVD
recorder and your TV screen (4:3
standard or 16:9 widescreen TV).
“4:3 Letter Box” has been selected as the default.
Press SETUP button to exit.
Changing the SETUP menu
3
Select “Playback” using K / L
/ { / B buttons, then press
ENTER button.
Note
Español
25
Others
If you have a standard TV:
Select “4:3 Letter Box”, so that
black bars appear on the top
and bottom of the screen.
Select “4:3 Pan & Scan” for a
full height picture with both
sides trimmed.
If you have a widescreen TV:
Select “16:9 Wide”.
Recording
Information on DVD recording
Information
Recording speed
This DVD recorder can record to DVD-R and
DVD-RW discs.When recording, you will need to
select a recording format between Video mode and
VR mode depending on the disc format.The disc
format for DVD-R is always “Video format,” so a
recording format will be “Video mode”.
On the other hand, when recording to DVD-RW, a
recording format will be “Video mode” or “VR
mode” because a disc format is available between
“Video Recording format” and “Video format” for
DVD-RW.
You can select a recording speed among 6 options,
and the recording time will depend on the recording speed you select as follows.
Logo
Attributes
12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
DVD-RW 600 minutes (4.7GB)
DVD-R
12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB)
About Video mode and VR (Video Recording)
mode
Video mode is the same recording format as DVDVideo discs purchased locally, so that you can play in
most DVD players.To play in other DVD players,
you will need to finalize (see page 39). Unless finalized, you can play, record additionally or edit discs
recorded in Video mode with this unit.
VR (Video Recording) mode is a basic recording
format for DVD-RW.You can record and edit
repeatedly.
DVD players with
are capable of playing
DVD-RW recorded in VR mode.
Disc type
Disc format
Functions
Video mode
Playing, limited recording,
limited editing
Video
DVD-RW
DVD-RW VR mode
VR
DVD-RW
Video mode
DVD-R
26
DVD-R
Playing, recording,
Original/Playlist editing
Playing, limited recording,
limited editing
Recording Recording
Video/Sound Quality
speed
time *
XP (1H)
60 min
SP (2H)
120 min
LP (4H)
240 min
EP (6H)
360 min
SLP (8H)
480 min
SEP (10H) 600 min
* This table is designed for a new single-sided 12cm
disc as the standard.The recording time are estimates and actual recording time may differ.
* The audio and video quality is getting poorer as
the Recording time becomes longer.
Restrictions on recording
You cannot record copy-protected video using this
DVD recorder. Copy-protected video includes
DVD-Video discs and some satellite broadcasts.
If copy-protected material is encountered during a
recording, recording will pause or stop automatically
and an error message will be displayed on-screen.
Video that is “copy-once only” can only be recorded
using a DVD-RW disc in VR mode with CPRM (see
below).
When recording a TV broadcast or through an
external input, you can display copy control information on screen.
What is “CPRM”?
CPRM is a copy protection system with scramble system regarding the recording of “copy
once” broadcast programs. CPRM stands for
Content Protection for Recordable Media.
This DVD recorder is CPRM compatible, which
means that you can record copy-once broadcast programs, but you cannot then make a
copy of those recordings. CPRM recordings can
only be made on DVD-RW discs formatted in
VR mode, and CPRM recordings can only be
played on players that are specifically compatible with CPRM.
Recording
Information on copy control
Some satellite broadcasts include copy-protected
information. For recording these, refer to the following.
Copy-free Copy-once Copyprohibited
Video mode
DVD-RW
ver.1.1
ver.1.1 CPRM
compatible
Recordable
Recordable only for DVD-RW ver.1.1 compatible
with CPRM
Not Recordable
Mode
DVD-R
ver.2.0
Video mode
DVD-RW
ver.1.1
ver.1.1 CPRM compatible
Video mode
Playing discs
Disc type
Recording
Video mode
DVD-R
ver.2.0
Getting started
VR mode
DVD-RW
ver.1.0
ver.1.1
ver.1.1 CPRM
compatible
You will need to finalize discs when in the following:
- when playing DVD-R/RW (Video mode) recorded
with this DVD recorder in other DVD players.
- when DVD-RW (VR mode) recorded with this
DVD recorder fails to be played in other DVD players.
• Once DVD-R/RW (Video mode) is finalized, you
cannot record additionally or edit.
• You can record additionally to or edit DVD-RW
(VR mode), which is finalized with this DVD
recorder.
• Be sure to finalize discs recorded with this DVD
recorder by using this DVD recorder.
• Title menu will be created automatically in DVDR/RW (Video mode) finalized with this DVD
recorder.
To play in other DVD players, finalize discs recorded
from this DVD recorder with the following condition.
Connections
Disc type/
format
Making discs playable in other DVD
player (Finalize)
Before you start
Information on DVD recording (cont’d)
Note
Editing
Changing the SETUP menu
• The audio and video quality is getting poorer as
the Recording time becomes longer.
• This recorder cannot record CD-R or CD-RW
discs.
• DVD-R/RW and CD-R/RW discs recorded using
a personal computer or a DVD or CD recorder
may not play if the disc is damaged or dirty, or if
there is dirt of condensation on the player’s lens.
• If you record a disc using a personal computer,
even if it is recorded in a compatible format,
there are cases in which it may not play because
of the settings of the application software used
to create the disc. (Check with the software publisher for more detailed information.)
Others
Español
27
Recording
Formatting a disc
Settings for the recording format to a blank disc
Video
VR
DVD-RW
DVD-RW
When inserting a blank disc, the
DVD recorder starts to initialize
the blank disc.
After that,You can record to the
disc with the recording format
selected in SETUP menu.
You are allowed to set a specified
time for chapter marks.
3
POWER
Select “Recording” using K /
L / { / B buttons, then press
ENTER button.
Recording menu will appear.
Auto Chapter
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
REC
Video mode
10 minutes
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Setup > Recording
DVD-RW Recording Format
OPEN/CLOSE
DISPLAY
PAUSE
SKIP
F
H
Timer Programming
G
B
PLAY
1
REV
FWD
h
g
STOP
C
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
4
Select “DVD-RW Recording
Format” using K / L buttons,
then press ENTER button.
Option window will appear.
2
3
4
5
Setup > Recording
Setup Menu
mode
DVD-RW Recording Format Video
VR mode
VR
mode
Auto Chapter
10 minutes
Timer Programming
2
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
Setup
Playback Setting
Video mode
DVD Player Compatibility mode.
VR mode
Editing possibility mode.
Video mode has been selected as
the default.
5
Select “Video mode” or “VR
mode” using K / L buttons,
then press ENTER button.
The recording mode will be set.
Note
• When inserting a blank
DVD+R or DVD+RW disc,
the error message ("Disc
Error") will appear.This DVD
recorder is not compatible
with a DVD+R/RW disc.
• If using a DVD-RW (ver 1.0)
disc, recording will start in VR
mode even you choose video
mode in SETUP menu.
28
Recording
Before you start
Formatting a disc (cont’d)
6
POWER
Select “Auto Chapter” using
K / L buttons, then press
ENTER button.
Option window will appear.
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
VR mode
OFF
5 minutes
10
minutes
10 minutes
15 minutes
30 minutes
60 minutes
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
8
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
“10 minutes” has been selected as
the default.
B
RETURN
ZOOM
L
6
7
Getting started
Timer Programming
.@/:
1
Connections
CH
Setup > Recording
Auto Chapter
TIMER
PROG.
A
REC
MONITOR
DVD-RW Recording Format
OPEN/CLOSE
DISPLAY
Recording
7
Playing discs
Select a desired time option
using K / L buttons, then
press ENTER button.
Chapter marks will be put as you
specified.
8
Press SETUP button to exit
SETUP menu.
Editing
Changing the SETUP menu
Others
Note
29
Español
• The time for chapter marks is
not accurate in Video mode.
Recording
Formatting a disc (cont’d)
Reformatting a disc
Video
VR
DVD-RW
DVD-RW
If you are using a DVD-RW disc,
by default it will be Video mode.
You can change this to VR mode
from SETUP menu.
1
4
POWER
Select “Yes” using { / B buttons, then press ENTER button.
Option window will appear.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
REC
MONITOR
REC SPEED CLEAR
Disc
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
REC
Edit
SPACE
0
PAUSE
H
Finalize
G
B
PLAY
Disc Protect OFF ON
REV
Yes
FWD
h
No
g
STOP
C
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
* VR mode only
B
RETURN
ZOOM
L
5
Select “Yes” using { / B buttons, then press ENTER button.
Formatting will start.
2
CM SKIP
SKIP
F
Format
Are you sure?
Yes
No
Setup Menu
OPEN/CLOSE
DISPLAY
2
3
4
5
Select “DISC” using { / B
buttons, then press ENTER
button.
DISC menu will appear.
Disc
58%
Edit
Formatting
Format
Finalize
Disc Protect OFF ON
6
Formatting is complete.
100% will be indicated.
* VR mode only
3
Select “Format” using K / L
buttons, then press ENTER
button.
Option window will appear.
Disc
This operation may take a
while to be completed.
Edit
Format
Finalize
Disc Protect OFF ON
Yes
* VR mode only
30
100%
Formatting
No
Note
• When you reformat the disc,
the contents of the disc will
be erased.
• If you want to cancel format
at step 5, select "No".
Recording
Before you start
Basic recording
DVD-R
Video
VR
DVD-RW
DVD-RW
Follow the steps below to record
TV programs.
Select a desired channel to
record using CH K / L buttons or number buttons.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
4
CH
REC
MONITOR
CH 1
OPEN/CLOSE
DISPLAY
2
5
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
B
PLAY
This operation may take a
while to be recognized.
REV
5
FWD
h
g
STOP
C
SETUP
4
TOP MENU
MENU/LIST
6
K
2
ENTER
REPEAT
SP 2:01 Rem.
5
To pause the recording, press
PAUSE F button. Press REC button to restart the recording.
6
Press STOP C button to stop
the recording.
This operation may take a
while to be completed.
Note
Español
31
Others
• Recording starts immediately
and continues until the disc is
full or you stop recording.
• When the clock setting has
not been made, the space for
a date and time of title names
in the original or playlist will
be blank.
• You cannot mix two formats
on one DVD-RW disc.
When you load a disc once
recorded before, the recording format cannot be changed
even you change it in SETUP
menu.
• You cannot change the
recording speed during the
REC pause mode.
• You can change a channel
during the REC pause mode.
Changing the SETUP menu
When a DVD-R disc is loaded:
DVD-R discs will always be in
Video mode.
I
Editing
When a DVD-RW disc is
loaded:
You can choose Video mode or
VR mode from SETUP menu.
“Video mode” has been selected
as the default. Refer to “Settings
for the recording format to a
blank disc” on pages 28-29.
Playing discs
Make sure that the recording
format is set to the desired
mode.
Refer to “Formatting a disc” on
pages 28-30.
L
Press REC button to start
recording.
REC mark will be displayed for 5
seconds.
Refer to “Recording speed” on
page 26.
3
B
RETURN
ZOOM
Recording
Select a recording speed
using REC SPEED button.
{
Getting started
Turn on the DVD recorder
and load a recordable disc.
Make sure that the TV input is set
on the DVD recorder.
POWER
Connections
1
4
Recording
Basic recording (cont’d)
Checking the recording picture quality
DVD-R
Video
VR
DVD-RW
DVD-RW
You can confirm the recording picture quality with the recording
speed you have selected before
attempting to record to a DVD disc.
1
While the DVD recorder is in
STOP or REC with a DVD
disc to record inserted, press
REC MONITOR button.
The TV program will be on the
screen in the recording picture
quality with the recording speed
you have selected.
POWER
2
Press REC MONITOR button
again to exit.
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
1
2
1
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
CH 18
Rec Monitor
XP
If you want to change the
recording speed, press REC
SPEED button repeatedly.
The recording speed will be change
as you press the button as shown.
Refer to “Recording speed” on
page 26.
• You cannot change the recording speed during recording.
XP
SP
LP
SEP
SLP
EP
Note
• You cannot check the recording sound with the Rec monitor function.
32
Recording
Before you start
One-touch timer recording
DVD-R
Video
VR
DVD-RW
DVD-RW
Turn on the DVD recorder
and load a recordable disc.
Make sure that the TV input is set
on the DVD recorder.
Select a desired channel to
record using CH K / L buttons or number buttons.
POWER
Press REC button on the
remote control or the front
panel, then press REC button
repeatedly until a desired
recording time (30 minutes
to 4 hours) appears on the TV
screen.
Recording will start.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
4
CH
REC
MONITOR
5
OPEN/CLOSE
DISPLAY
2
5
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
5
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Recording
This operation may take a
while to be recognized.
2
I
Playing discs
Select a recording speed
using REC SPEED button.
Refer to "Recording speed" on
page 26.
0:30
0:30
Normal REC
1:00
3
When reaches the specified time,
the DVD recorder will be turned
off automatically.
To cancel the one-touch timer
recording within the specified
time, press STOP C button.
This operation may take a
while to be completed.
Note
33
Español
The DVD recorder will be
turned off automatically under
the conditions following.
• No space remained on the
disc.
• When a power failure occurs.
Others
When a DVD-R disc is loaded:
DVD-R discs will always be in
Video mode.
3:30
Changing the SETUP menu
When a DVD-RW disc is
loaded:
You can choose Video mode or
VR mode from SETUP menu.
"Video mode" has been selected
as the default. Refer to pages 2829 "Settings for the recording format to a blank disc."
4:00
Editing
Make sure that the recording
format is set to the desired
mode.
Refer to "Formatting a disc" on
pages 28-30.
Getting started
1
4
Connections
This is a simple way to set the
recording time in blocks of 30
minutes. Check that the disc you
are recording onto has enough
space for the time you set.
When the recording finishes the
recorder automatically goes into
standby.
Recording
Timer recording
DVD-R
Video
VR
DVD-RW
DVD-RW
You can program the unit to
record up to 8 programs, up to a
year in advance. Daily or weekly
program recordings are also available.
• Be sure to set the clock before
making a timer programming.
• Insert a recordable disc.
4
Select “Timer Programming”
using K / L buttons, then
press ENTER button.
Timer Programming list will
appear.
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
Setup > Recording > Timer Programming
Date
1. - - 2. - - 3. - - 4
Start
End
CH
Speed
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
REC
5
SPACE
0
PAUSE
F
H
PLAY
REV
FWD
h
g
STOP
C
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
L
6
Enter the date using K / L
buttons, then press B button.
Setup > Recording > Timer Programming
Date
Start
1. JAN / 01 - - : - -AM
2. - - 3. - - 4. - - -
Select SETUP using { / B
buttons, then press ENTER
button.
SETUP menu will appear.
G
B
Select the program which is
not set up using K / L buttons, then press ENTER button.
2
CM SKIP
SKIP
ZOOM
Setup Menu
OPEN/CLOSE
DISPLAY
A
1
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
You can choose the timer
programming menu by pressing TIMER PROG. button. In
this case, continue with step 5.
End
CH
- - : - -AM CH8
Speed
2
3
4
5
6
7
e.g. January 1st
When pressing L button at the
current date, timer recording
mode will change as follows.
JAN/01
L
Setup
Daily
L
MON-SAT
L
MON-FRI
L
SAT
Playback Setting
L
FRI
L
3
Note
L
SUN
L
Select “Recording” using K /
L / { / B buttons, then press
ENTER button.
Recording menu will appear.
7
Setup > Recording
DVD-RW Recording Format
Auto Chapter
Timer Programming
DEC/31
Video mode
10 minutes
Enter the time to start and
to end using K / L buttons,
then press B button.
Setup > Recording > Timer Programming
34
Date
Start
1. JAN/12 10 :00PM
2. - - 3. - - 4
End
CH
- - : - -AM CH8
Speed
• If you have not set the
clock yet:
A clock setting window will
appear after step 4. Continue
with the step 4 in “Auto
Clock Setting” on page 21 or
“Manual Clock Setting” on
page 22 before making a
timer programming.
• Press { or B buttons to
move the cursor to the left
and the right in the timer
programming menu.
Recording
Before you start
Timer recording (cont’d)
10
Select the channel number to
record using K / L buttons,
then press B button.
Press ENTER button when all
information required is
entered. Your program setting
will be stored.
• To set another program, repeat
steps 5 to 10.
• To exit, press SETUP button.
Setup > Recording > Timer Programming
Date
Start
1. JAN/12 10:00PM
2. - - -
End
CH
10:30PM CH8
Speed
9
Select a recording speed
using K / L buttons.
11
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
REC
DEF
3
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
11
C
SETUP
TOP MENU
MENU/LIST
K
Press POWER button to turn
indicator will appear on
off.
the front display.
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Setup > Recording > Timer Programming
End
CH
10:30PM CH8
Note
Speed
1H
Refer to “Recording speed” on
page 26.
4
Press POWER button so that
indicator disappear from the
front display.
To clear the timer programming,
select your desired program
using K / L buttons.Then,
CLEAR button.
POWER
1
6
Press TIMER PROG. button.
Timer Programming list will appear.
Date
Start
1. JAN/12 10:00PM
2. - - -
End
CH
10:30PM CH8
Speed
1H
.@/:
1
ABC
2
DEF
3
CH
GHI
4
JKL
5
MNO
6
4
REC
Check the information on the
list you will need.
WXYZ
9
CM SKIP
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
3
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
2
5
5
{
B
RETURN
ZOOM
4
L
Press TIMER PROG. button to exit.
Press POWER button to return
to the timer standby mode.
Press STOP C button on the front panel of the main unit. STOP C button on the remote control is not effective.
35
Español
To stop the timer recording in process
Note
• Pressing TIMER PROG. button
to check the timer programming in proceed.
When the timer recording is
proceeding, the proceeding
program will be highlighted
with red. In this case, you cannot select other program.
Others
6
Changing the SETUP menu
Setup > Recording > Timer Programming
To correct the timer programming, select your desired program using K / L buttons.Then,
press ENTER button. Next, correct the timer programming by using
press K/L/{/B buttons.
Finally, press ENTER button again.
TIMER
PROG.
A
REC
MONITOR
2
OPEN/CLOSE
DISPLAY
Editing
1
Playing discs
Checking, canceling, or correcting the timer programming
information
• After step 11, the DVD
recorder will be turned on
automatically 2 minutes in
advance of the recording time
to start and waits to start.
Then the recording will start
at the recording time you set.
Recording
Date
Start
1. JAN/12 10:00PM
2. - - -
8
9
10
Getting started
To record from external input, L1
or L2.
POWER
Connections
8
Recording
Timer recording (cont’d)
Hints for timer recording
• If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a disc is not on the tray, the
indicator flashes and timer recording cannot be performed. Please insert a recordable disc.
• When all the timer recording are completed, the
indicator flashes.To play or eject the recorded disc, press
POWER button first, and then press PLAY B or OPEN/CLOSE A button.
The priority of overlapped settings
This unit records the programs according to priority if the timer programmings are overlapped.The timer programming
set previously has priority.
If the timer programmings are overlapped, the program that has priority will be recorded. A timer recording of lower
priority will be canceled, start from the middle, or stop on the way.
Check the overlapped timer programmings and change the priority if necessary.
A programming set previously has priority
When the starting time is same:
A program set previously (PROG. 1) has priority.
ex.1
When some programming have been
made at the end time of the
programming currently being recorded:
A program set previously (PROG. 2) has priority.
ex. 2
PROG. 1
PROG. 1
PROG. 2
PROG. 2
PROG. 3
Actual
recording
PROG. 1
PROG. 2
Actual
recording
PROG. 1
PROG. 2
When the recording time is partially overlapped:
PROG. 1 will start after PROG. 2 is complete to be recorded.
PROG. 1
PROG. 2
Actual
recording
PROG. 2
PROG. 1
When the recording time is entirely overlapped:
PROG. 1 will not be recorded.
PROG. 1
PROG. 2
Actual
recording
PROG. 2
When the end time of the programming currently being recorded and the starting time
of the one to be recorded sequentially are same:
The first 20-90 seconds of the programming to be recorded sequentially will be cut off.
PROG. 1
PROG. 2
Actual
recording
PROG. 1
PROG. 2
The first 20-90 seconds will be cut off.
36
Recording
Before you start
Settings for an external source
Connection to an external source
DVD-R
Video
VR
DVD-RW
DVD-RW
Connect the external source properly to the DVD recorder by using input jacks either LINE2 (Front) or
LINE1 (Rear).
VIDEO AUDIO
L
or
OUTPUT
AUDIO
R
R
Audio/Video
cable
Audio/Video
cable
VIDEO S -VIDEO
L
or
S-Video
cable
Getting started
S-Video
cable
Connections
Another source
(VCR camcorder etc.)
OUTPUT
S- VIDEO
or
To LINE 2 IN
Front of DVD recorder
To LINE 1 IN
Rear of DVD recorder
Setup > Select Video
1. Press SETUP button to display SETUP/DISC
menu.
2. Select “SETUP” using { / B buttons, then
press ENTER button.
3. Select “Select Video”, then press ENTER
button.
Setup > Select Video
L1 (Rear)
Video In
L1 (Rear)
Video In
L2 (Front)
Video In
L2 (Front)
Video In
Setup > Select Video
L2 (Front)
Setup > Select Video
Video
Video
In In
S-Video
Video In
Setup > Select Video
L2 (Front)
Video
Video
In In
S-Video
Video In
5. Select the input jack type to connect, then
press ENTER button.
If you want to use S-VIDEO INPUT, select “S-Video
In”.
If you want to use VIDEO INPUT (Composite),
select “Video In”.
Others
5. Select the input jack type to connect, then
press ENTER button.
If you want to use S-VIDEO INPUT, select “S-Video
In”.
If you want to use VIDEO INPUT (Composite),
select “Video In”.
L1 (Rear)
Changing the SETUP menu
L1 (Rear)
4. Select “L1 (Rear)”, then press ENTER button.
Editing
4. Select “L2 (Front)”, then press ENTER button.
Playing discs
1. Press SETUP button to display SETUP/DISC
menu.
2. Select “SETUP” using { / B buttons, then
press ENTER button.
3. Select “Select Video”, then press ENTER
button.
Recording
FWD
Setup > Select Video
L1 (Rear)
Video In
L1 (Rear)
S-Video In
L2 (Front)
S-Video In
L2 (Front)
Video In
Español
37
Recording
Settings for an external source (cont’d)
Recording from an external source
DVD-R
Video
VR
DVD-RW
DVD-RW
Before recording from an external source, see the instructions for the connection on page 37.
1. Turn the TV and the DVD recorder on, and be sure to select
the input of the TV to which the DVD recorder is connected.
2. Press OPEN/CLOSE A button to open the disc tray, then
place the disc to record properly.
POWER
1
3. Select the input of the DVD recorder which the external
equipment is connected. (L2 or L1)
• To use the input jacks on the back of this unit, select “L1” position by
pressing [0], [0], [1] on the remote control or the CH L / K buttons.
• To use the input jacks on the front of this unit, select “L2” position by
pressing [0], [0], [2] on the remote control or the CH L / K buttons.
CH
4
5
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
REC
MONITOR
This operation may take a while to be recognized.
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
XP
SP
LP
SEP
SLP
EP
5. Press REC button on the DVD recorder to start recording.
6. Press Play button on the external source to record from.
7. Press STOP C button on the DVD recorder to stop recording.
This operation may take a while to be completed.
38
2
3
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
4. Select a recording speed using REC SPEED button. Refer to
“Recording speed” on page 26.
OPEN/CLOSE
DISPLAY
B
RETURN
ZOOM
L
7
Recording
Before you start
Finalizing the discs
DVD-R
Video
VR
DVD-RW
DVD-RW
Disc
You will need to finalize the discs
recorded in Video mode to play in
other DVD players.
Finalizing discs in Video mode
automatically create title menus.
Edit
POWER
Format
Finalize
.@/:
1
ABC
2
DEF
3
No
CH
GHI
4
JKL
5
MNO
6
WXYZ
9
CM SKIP
PAUSE
SKIP
F
Select “Yes” using { / B buttons, then press ENTER button.
Finalizing will start.
H
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
1
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
58%
Finalizing
Select “DISC” using { / B
buttons, then press ENTER
button.
DISC menu will appear.
Video mode:
To cancel finalizing, press STOP C
button.
Do you want to cancel?
Yes
No
58%
Finalizing
Edit
Format
Finalize
Disc Protect OFF ON
3
Finalizing is complete.
100%
Finalizing
Format
Undo Finalize
To release the finalizing for
the disc, select “Undo
Finalize” at step 3.
• If
appear when pressing
STOP button, you cannot cancel finalizing because the finalizing has been in certain
progress.
When selecting “No” and
press ENTER or RETURN
button, finalizing will be continued.
You cannot cancel finalizing
the DVD-R disc when it has
been started.
39
Español
This operation may take a
while to be completed.
Edit
Others
Select “Finalize” using K / L
buttons, then press ENTER
button.
Option window will appear.
5
Disc
Changing the SETUP menu
* VR mode only
Select “Yes”, then press
ENTER button.
Finalizing is cancelled, then the
DVD recorder will be in stop
mode.
Editing
Disc
Note
• Once you have finalized a disc
recorded in Video mode, you
cannot edit or record anything else on that disc.
A VR mode disc can still be
recorded and edited on this
recorder even after finalizing.
• When you insert a DVD-RW
disc finalized with this DVD
recorder, “Undo Finalize” will
appear instead of “Finalize”.
Playing discs
2
4
2
3
4
Recording
Setup Menu
G
Getting started
REC
4
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
Connections
Yes
* VR mode only
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
TIMER
PROG.
A
Disc Protect OFF ON
REC
MONITOR
1
OPEN/CLOSE
DISPLAY
Recording
Setting a disc to protect
VR
DVD-RW
To prevent accidental recording,
editing, or erasing the titles, you
can protect them from DISC
menu.
3
Select “Disc Protect OFF ➔
ON” using K / L buttons,
then press ENTER button.
Option window will appear.
1
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
REC
MONITOR
REC SPEED CLEAR
Disc
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
Screen:
OPEN/CLOSE
DISPLAY
Edit
REC
Format
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
Finalize
Disc Protect OFF
Yes
ON
B
PLAY
REV
No
FWD
h
g
STOP
C
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
4
Setup Menu
Select “Yes” using { / B buttons, then press ENTER button.
A disc will be protected.
2
Select “DISC” using { / B
buttons, then press ENTER
button.
DISC menu will appear.
58%
Disc
Writing to Disc
Edit
Format
Finalize
Disc Protect OFF ON
40
This operation may take a
while to be completed.
2
3
4
Playing discs
Before you start
Information on DVD play
Before you attempt to play DVD discs, read the following information.
Playable discs
Logo
This DVD recorder has been designed to play DVD
discs with Region One (1). DVDs must be labeled
for ALL regions or for Region 1 in order to play on
the the DVD recorder.You cannot play DVDs that
are labeled for other regions. Look for the symbols
below on your DVDs. If these region symbols do
not appear on your DVD, you cannot play the DVD
in this DVD recorder.
DVD VIDEO
Getting started
Disc
Region codes
Connections
This DVD recorder is compatible to play the following discs.
To play a DVD, make sure that it meets the requirements for Region Codes and Color Systems as
described below. Discs that have the following logos
will play on the DVD recorder. Other Disc types
are not guaranteed to play.
DVD-RW (VIDEO/VR FORMAT)
DVD-R (VIDEO FORMAT)
CD-DA (AUDIO CD)
The contents of DVD disc are generally divided into
some titles.Titles may be further subdivided into
chapters.
CD-RW (CD-DA FORMAT, MP3 files)
Start Rec.
Stop/Start
Stop Rec.
Title 1
Editing
Color systems
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
Changing the SETUP menu
DVDs are recorded in different color systems
throughout the world.The most common color systems are NTSC (which is used primarily in the
United States and Canada), PAL, and SECAM.
This DVD Recorder uses NTSC, so DVDs you play
must be recorded in the NTSC system.You cannot
play DVDs recorded in other color system .
Guide to displays
3
1
1
1
00:00:00
DVD-RW
Video mode
4
2
: Search
: Audio
: Subtitle
: Angle (except VR mode)
: Repeat
: Marker
: Noise Reduction
Español
SP 1:25 Rem.
1. Indicates a disc type and a
format mode.
2. Indicates a recording speed
and possible recording time. /
Indicates a channel number.
3. Indicates a title number, chapter number, and the time
lapse of disc play.
4. Each icon means:
Others
Press DISPLAY button to call up
the display menu.This menu will
give you the information on the
playing disc. Some operations are
available while disc is playing.
Playing discs
Hint for DVD playback
CD-R (CD-DA FORMAT, MP3 files)
Recording
The number inside the globe refers to region of the
world. Region 1 represents the United States,
Canada, Bermuda, the U.S.Virgin Islands, and small
regions near Australia.
A DVD labeled for a specific region can only play on
the DVD recorder with the same region code.
: Zoom
41
Playing discs
Basic playback
Playback
DVD-R
Video
VR
DVD-RW
DVD-RW
VR mode:
POWER
Original
1
1
JAN/1 12:00AM
4
JAN/1 1:00AM
JAN/1 2:00AM
1
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
REC
MONITOR
5
JAN/1 3:00AM
JAN/1 4:00AM
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
2
6
SKIP
F
H
G
MENU / LIST button
B
PLAY
Playlist
1
2
JAN/1 12:00AM
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
REV
6
4
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
Press OPEN/CLOSE A button to open the disc tray.
The disc tray will open.
Place the disc onto the disc
tray with its label facing up
and make sure to align the
disc to the disc tray guide.
3
CH
Press POWER button on the
remote control or the front
panel of the DVD recorder.
When you are playing a DVD, turn
the TV on and be sure to select
the input to which the DVD
recorder is connected.
3
1
2
OPEN/CLOSE
DISPLAY
4
JAN/1 3:00AM
5
4
5
L
JAN/1 4:00AM
5
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Playing will start.
6
disc
tray
guide
This operation may take a
while to be recognized.
Press STOP C button to stop
play.
Note
To eject the disc, press
OPEN/CLOSE A button to open
the disc tray, then remove the disc
before turn the DVD recorder off.
• For DVD-R (Video mode)
and DVD-RW (Video mode)
discs which are already finalized, a title list will be displayed instead of thumbnails.
4
Title Menu
Press TOP MENU button to
display the title menu.
You can change “Original” or
“Playlist” of VR mode using
MENU / LIST button.
Video mode:
Title List
1
JAN/1 12:00AM
4
JAN/1 3:00AM
42
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
5
JAN/1 4:00AM
1 JAN/1
12:24AM
CH96
XP
2
3
4
5
6
7
8
• You can resume play from
where you stopped playing
the disc. (Resume play)
Refer to page 46 for details
about resume play.
• Some discs may start playing
automatically.
Playing discs
DVD-V
CD
MP3
1
Place the disc onto the disc
tray with its label facing up
and make sure to align the
disc to the disc tray guide.
POWER
1
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
4
OPEN/CLOSE
DISPLAY
REC
WXYZ
9
CM SKIP
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
2
SETUP
Press OPEN/CLOSE A button to open the disc tray.
The disc tray will open.
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Note
• Some discs may start playing
automatically.
7
1
In stop mode, press TOP
MENU button to call up the
MP3 menu.
REC SPEED CLEAR
REC
1/ 2
• To exit the menu, press TOP
MENU button again.
Press K / L buttons to select a
desired folder (group) or track,
then press ENTER button.
When selecting track:
Playback will start.
B
PLAY
REV
FWD
h
1
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
{
B
RETURN
ZOOM
2
L
Note
• The audio source of MP3 files
cannot be recorded as digital
sound by an MD or DAT
deck.
• Files whose extension is
other than “.mp3(MP3)” will
not be listed in the MP3
menu.
• Some unplayable folders or
tracks may be listed in the
MP3 menu due to the recording status..
43
Español
When selecting the folder:
The files in folder will appear.
This unit recommends the files
recorded under the following circumstances:
• Sampling frequency: 44.1kHz or 48kHz.
• Constant bit rate: 112kbps - 320kbps.
G
Others
2
H
Changing the SETUP menu
FOLDER NAME 1
FOLDER NAME 2
FOLDER NAME 3
FOLDER NAME 4
FOLDER NAME 5
FOLDER NAME 6
1 FILE NAME 1
2 FILE NAME 2
SKIP
F
List of MP3 Files
Hints for MP3 files:
• Folders are known as Groups,
files are known as Tracks.
• Folders are accompanied by
icon.
• MP3 files are accompanied by icon.
Reproduction will start from the
selected track and go to the
next one in turn.
• The system can recognize up to 255
groups (or folders) and up to 255 tracks.
• The name of group and track can
be displayed in up to 32 characters. Unrecognizable characters
will be replaced with asterisks.
• If there is no files in the folder,
“No Files” will be displayed.
9
CM SKIP
PAUSE
REPEAT
DISC NAME
8
SPACE
0
Editing
Press K / L buttons to select the
track or folder you want, then
press ENTER button.
• Press s button or RETURN
button to the previous hierarchy.
• Press STOP button to return to
the first to the first item.
Playing discs
For MP3 playback
Recording
Press STOP C button to stop
playing.
MENU/LIST
K
If you are playing a DVD-Video
disc, a menu may appear.
Refer to pages 44-45 for details
about a disc menu.
5
TOP MENU
4
5
Getting started
Press PLAY B button to start
playing.
Playing will start.
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
2
Connections
Press POWER button on the
remote control or the front
panel of the DVD recorder.
When you are playing a DVD, turn
the TV on and be sure to select
the input to which the DVD
recorder is connected.
3
Before you start
Basic playback (cont’d)
Playing discs
Basic playback (cont’d)
Playing discs using the disc menu
DVD-V
A DVD disc contains a disc menu
that describes the contents or
allows you to customize the playback. For example, the menu may
offer choices for subtitle languages, special features, or chapter
selection.
Sometimes these are displayed
automatically when you start playback, otherwise only appear when
you press MENU / LIST button.
1
Press MENU / LIST button.
The DVD main menu will appear.
If the feature is not available,
may appear on the TV screen.
2
Select an item using K / L /
{ / B buttons, then press
ENTER button to confirm.
Continue this step to set up all
the features you want or to start
playing the disc from the menu.
POWER
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
MENU / LIST button:
Displays a DVD disc menu which
varies with the disc and may be
the same as the ‘Top menu.’
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
K / L / { / B buttons:
Moves the cursor around screen.
B
RETURN
ZOOM
L
Enter button:
Selects the currently highlighted
menu option.
Number buttons:
Selects a numbered menu option
(some discs only). (Press ENTER
button after.)
3
Press MENU / LIST button to
exit the menu.
Note
• Menus vary among discs.
Refer to the information
accompanying the disc for
details.
44
2
1
2
3
2
Playing discs
Before you start
Basic playback (cont’d)
Playing discs using the title menu
DVD-V
1
If the feature is not available,
may appear on the TV screen.
POWER
Select a title to play using the
K / L / { / B buttons, then
press ENTER button.
Play will begin at the title you
selected.
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
TOP MENU button:
Displays the ‘Top menu’ of a DVD
disc which varies with the disc.
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
2
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
K / L / { / B buttons:
Moves the cursor around screen.
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
2
L
Recording
Enter button:
Selects the currently highlighted
menu option.
1
2
3
Getting started
Press TOP MENU button.
The title menu will appear.
2
Connections
Some DVDs have a title menu,
which lists the titles available on
them. It helps you to start play at
a specific title.
Playing discs
Number buttons:
Selects a numbered menu option
(some discs only). (Press ENTER
button after.)
3
Press TOP MENU button to
exit the title menu.
Editing
Changing the SETUP menu
Others
Note
Español
• The TOP MENU button will
not always active with all
DVDs.
• Menus vary among discs.
Refer to the information
accompanying the disc for
details.
45
Playing discs
Special playback
Resume play
Video
DVD-V
DVD-R
DVD-RW
2
VR
CD
DVD-RW
MP3
1
During play, press STOP C
button.
The resume message will appear.
Screen:
TIMER
PROG.
.@/:
1
ABC
2
A
Press PLAY B button.
In a few seconds, play will resume
from the point at which it
stopped last.You can resume play
at the same point even if you turn
off the DVD recorder.
You can resume play from where
you stopped playing the disc last.
DISPLAY
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
REC
DEF
3
PAUSE
SKIP
F
H
G
B
PLAY
REV
To cancel the resume play and
start playing the disc from the
beginning, press STOP C button
the second time while the play is
stopped.
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
2
1
2
RETURN
ZOOM
L
Note
• For MP3 files, playback will
resume from the beginning of
the track at which playback
was stopped.
Resume ON
Fast forward / Fast reverse
DVD-V
DVD-R
Video
VR
DVD-RW
DVD-RW
CD
MP3
CH
1
REC
MONITOR
JKL
5
GHI
4
During play, press FWD D or REV E button.
Every time you press FWD D or REV E button, approximate speed
will be changed as follows.
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
MNO
6
PAUSE
SKIP
F
H
G
B
PLAY
x40
FWD
FWD
FWD
g
g
g
REV
h
x20
REV
h
x5
REV
h
Normal
speed
playback
FWD
FWD
FWD
g
g
g
REV
h
x2
REV
h
x20
REV
h
x40
1
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
1
1
K
ENTER
REPEAT
{
B
RETURN
ZOOM
For Audio CDs, approximate speed is fixed at x8 with sound.
For MP3 files, approximate speed is fixed at x8.
To return to the normal play, press PLAY B button.
L
Note
• Forward/reverse speed will be
indicated with icons as follows.
Forward (Approx. Speed)
x2:
x20:
x40:
Reverse (Approx. Speed)
x5:
x20:
x40:
46
Playing discs
Before you start
Special playback (cont’d)
Skipping TV commercials during play
DVD-R
Video
VR
DVD-RW
DVD-RW
e.g. Press CM SKIP button once
POWER
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
CM Skip
30 sec.
1
REC
WXYZ
9
CM SKIP
PAUSE
SKIP
F
H
1
Getting started
During play, press CM SKIP
button.
Normal play will start at 30 seconds ahead from the point you
press CM SKIP button.
Every time you press CM SKIP
button, searching point will be
extended by 30 second ahead.
You can press up to 6 times (180
seconds).
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
G
(forwarding 30 seconds.)
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Recording
B
Playback will restart automatically.
Playing discs
Pause
Video
DVD-V
DVD-R
DVD-RW
VR
DVD-RW
CD
MP3
1
2
POWER
Press PLAY B button to
resume play.
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
REC
MONITOR
REC SPEED CLEAR
REC
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
REV
Changing the SETUP menu
1
2
Editing
During play, press PAUSE F
button.
Play will pause and sound will be
muted.
Connections
You can skip TV commercials by
pressing CM SKIP button, so that
you can enjoy the recorded programs without interrupting.
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Others
Español
47
Playing discs
Special playback (cont’d)
Step by step playback
Video
DVD-V
DVD-R
DVD-RW
2
VR
DVD-RW
POWER
Press SKIP G button
repeatedly.
The play will advance one frame
(or step) at a time you press the
button with the sound muted.
1
During play, press PAUSE F
button.
Play will pause and sound will be
muted.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
1
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
To play step by step backward:
Press SKIP H button repeatedly.
Every time you press the button,
the play will go backward by one
frame.
OPEN/CLOSE
DISPLAY
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
2
3
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
3
L
Press PLAY B button to
resume play.
Slow forward / Slow reverse play
DVD-V
DVD-R
Video
VR
DVD-RW
DVD-RW
1
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
During play, press PAUSE k button, then press FWD D or
REV E button.
Every time you press FWD D or REV E button, approximate speed
will be changed as follows.
CH
REC
MONITOR
REC SPEED CLEAR
x1/4
FWD
FWD
FWD
FWD
FWD
FWD
g
g
g
g
g
g
REV
h
x1/8
REV
h
x1/16
Pause
REV
REV
h
h
x1/16
REV
h
To return to the normal play, press PLAY B button.
x1/8
REV
h
x1/2
OPEN/CLOSE
DISPLAY
1
1
REC
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
1
1
MENU/LIST
K
ENTER
REPEAT
{
B
Note
• Forward/reverse speed will be
indicated with icons as follows.
Forward (Approx. Speed)
x1/16:
x1/8:
x1/2:
Reverse (Approx. Speed)
x1/16:
x1/8:
x1/4:
48
Playing discs
Before you start
Special playback (cont’d)
Zoom
B
PLAY
REV
Video
DVD-V
DVD-R
DVD-RW
VR
DVD-RW
During play, press ZOOM button.
Zoom menu will appear.
Screen:
1
x1.2
01:23:45
x1.5
C
2
Select a desired zoom factor
to zoom using { / B buttons,
then press ENTER button.
The zoom area will be displayed.
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
1
L
2
3
DVD-Video
Note
x2.0
3
B
Select a desired zoom position
using K / L / { / B buttons, then
press ENTER button.
The zoom play will start.
Recording
There are four options
(x1.0,x1.2,x1.5 and x2.0), these
are displayed excluding the current zoom rate.
• When selecting a smaller factor
than the current one, the zoom
area will not be displayed.
• To cancel the zoom function,
select x1.0 using { / B buttons,
then press ENTER button.
• To remove the zoom menu, press
ZOOM button again at step 1.
Getting started
1
g
STOP
Connections
1
FWD
h
Marker Setup
DVD-V
DVD-R
DVD-RW
Screen for DVD:
1
VR
1
DVD-Video
01:23:45
1
CH
1
2
3
4
5
6
This feature allows you to assign
a specific point on a disc to be
called back later.
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CD
DVD-RW
Playing discs
POWER
Video
REC
MONITOR
REC
WXYZ
9
CM SKIP
PAUSE
SKIP
F
H
G
Editing
1
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
B
PLAY
REV
FWD
h
g
Screen for CD:
STOP
C
SETUP
TOP MENU
MENU/LIST
K
1
01:23:45
Audio CD
ENTER
REPEAT
{
1
2
3
4
5
B
6
RETURN
ZOOM
1
1
01:23:45
L
DVD-Video
2
3
4
Note
2
4
To return to the marker later,
select the desired marker
number using { / B buttons,
then press ENTER button.
49
Español
Select
icon using { / B
buttons, then press ENTER
button.
Marker setup menu will appear.
ber using { / B buttons.
When reaches the desired
point, press ENTER button.
Others
3
Select a desired marker num-
• To clear a marker, select the
marker number to be cleared,
then press CLEAR button.
• All markers will be erased
when you operate these operations listed below.
– Opening the disc tray.
– Turning off the power.
– Recording to a recordable
disc.
– Changing the mode between
Original and Playlist.(VR mode)
• You can mark up to 6 points.
Changing the SETUP menu
During play, press DISPLAY
button.
The display menu will appear.
Screen:
Playing discs
Search
Title/Chapter search
Video
DVD-V
DVD-R
DVD-RW
VR
DVD-RW
POWER
Using SKIP H / G buttons
Using DISPLAY button
1
1
During play, press SKIP G
button to skip the current
title or chapter and move to
the next.
The title or chapter will move
forward by one at a time.
During play, press DISPLAY
button.
The display menu will appear.
Screen:
1
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
2
1
B
PLAY
1
1
01:23:45
DVD-Video
REV
FWD
h
g
STOP
C
SETUP
To go back to the previous title
or chapter, press SKIP H button.The title or chapter will move
backward by one at a time.
MENU/LIST
K
ENTER
REPEAT
{
2
Select
icon using { / B
buttons, then press ENTER
button.
‘T’ for title will be highlighted.
Title:
Enter a desired title number
to search using K / L buttons
or number buttons, then
press ENTER button.
Title search will start.
Chapter:
To move to ‘C’ for chapter, press
B button.
Enter a desired chapter number to search using K / L buttons or number buttons, then
press ENTER button.
Chapter search will start.
50
TOP MENU
B
RETURN
ZOOM
L
2
Playing discs
Before you start
Search (cont’d)
Track search
CD
MP3
Using SKIP H / G buttons
Using DISPLAY button
During play, press SKIP G
button to skip the current
track and move to the next.
The track will move forward by
one at a time.
During play, press DISPLAY
button.
The display menu will appear.
Screen:
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
1
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
1
To go back to the previous track,
press SKIP H button.The track
will move backward by one at a
time.
01:23:45
H
G
Audio CD
1
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
2
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
Recording
Select
icon using { / B
buttons, then press ENTER
button.
‘T’ for track will be highlighted.
Getting started
1
OPEN/CLOSE
DISPLAY
Connections
1
POWER
3
Playing discs
Enter a desired track number
to search using K / L buttons
or number buttons, then
press ENTER button.
Track search will start.
POWER
Video
DVD-V
DVD-R
DVD-RW
VR
CD
DVD-RW
1
01:23:45
.@/:
1
ABC
2
OPEN/CLOSE
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
REC
DEF
3
SPACE
0
PAUSE
Changing the SETUP menu
During play, press DISPLAY
button.
The display menu will appear.
Screen for DVD:
Select
icon using { / B
buttons, then press ENTER
button.
‘T’ for title or track will be highlighted.
To move to the clock icon, press
B button.
TIMER
PROG.
A
1
CH
1
1
2
DISPLAY
Editing
Time search
CM SKIP
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
DVD-Video
SETUP
TOP MENU
MENU/LIST
K
Screen for CD:
1
01:23:45
Audio CD
Enter a desired time to
search using K / L buttons or
number buttons, then press
ENTER button.
Time search will start.
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
Others
3
Note
51
Español
• Time search function is available only in the same track or
title.
Playing discs
Repeat/Random/Program playback
Repeat play
Video
DVD-V
DVD-R
DVD-RW
VR
CD
DVD-RW
MP3
1
Chapter:
The current chapter will be played
repeatedly. (DVD only)
CH
REC
MONITOR
1
2
3
GHI
4
JKL
5
MNO
6
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
During play, press REPEAT
button.
Repeat menu will appear.
Screen:
1
1
01:23:45
DVD-Video
OFF
Title
Chapter
A-B
2
Select a desired option to
repeat using K / L buttons,
then press ENTER button.
The selected repeat play will start.
Title:
The current title will be played
repeatedly. (DVD only)
All:
The current disc will be played
repeatedly. (CD, MP3, DVD-RW
(VR mode) only)
A-B:
The A-B point will be played
repeatedly.
When pressing ENTER button
while A-B is highlighted, the starting point (A) will be decided.
Press ENTER button again to
select the ending point (B).
Track:
The current track will be played
repeatedly. (CD, MP3 only)
Group:
The current group will be played
repeatedly. (MP3 only)
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
1
{
B
2
RETURN
ZOOM
L
Note
• The A-B Repeat playback can
only be set with in the current title (for DVDs), or current track (for Audio CDs).
• To cancel the repeat playback,
select OFF at step 2.
• You cannot select “Group”
during the random playback
of MP3 files.
Random playback
MONITOR
CD
MP3
With this function, you can play a
disc randomly instead of playing in
the original order.
1
Press SETUP button to display SETUP/CD menu.
SETUP/CD menu will appear.
Screen:
2
TUV
8
PQRS
7
REC SPEED CLEAR
REC
Select “CD” using { / B buttons, then press ENTER button.
CD Playback Mode menu will
appear.
SPACE
0
PAUSE
WXYZ
9
CM SKIP
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
1
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
CD Playback Mode
L
Random Play
Program Play
2
3
3
Setup Menu
52
Select “Random Play” using
K / L buttons, then press
ENTER button.
Random play will start.
Note
• To cancel random play, press
STOP C button twice during
random play.
Playing discs
Before you start
Repeat/Random/Program playback (cont’d)
Program play
CD
You can program the disc to play
in your desired order.
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
CD Playback Mode > Program Play
REC
-- -- -- -- -- -- -- -- -- --
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
-- -- -- -- -- -- -- -- -- --- -- -- -- -- -- -- -- -- --
B
PLAY
-- -- -- -- -- -- -- -- -- --
REV
FWD
h
g
-- -- -- -- -- -- -- -- -- --
5
STOP
C
Total
00:00:00
SETUP
1
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
2
Playing discs
Select “CD” using { / B buttons, then press ENTER button.
CD Playback Mode menu will
appear.
Select a desired track using K
/ L buttons, then press
ENTER button or B button.
A cursor will move to next.
2
3
4
CD Playback Mode > Program Play
07 - - - - - - - - - - - - - - - -
--
-- -- -- -- -- -- -- -- --
--
-- -- -- -- -- -- -- -- --
--
-- -- -- -- -- -- -- -- --- -- -- -- -- -- -- -- --
---
Recording
Setup Menu
L
4
Getting started
Press SETUP button to display SETUP/CD menu.
SETUP/CD menu will appear.
Screen:
POWER
Select “Program Play” using
K / L buttons, then press
ENTER button.
Program play list will appear.
Connections
1
3
CD Playback Mode
Total
Random Play
00:04:30
Program Play
Editing
5
Changing the SETUP menu
Press PLAY B button to start
program play.
Program play will start.
Note
Español
53
Others
• To erase tracks you selected,
press CLEAR button.
• You can make program settings up to 50.
• To cancel program play, press
STOP C button twice during
program play.
• You may also select a desired
track using Number buttons
at step 4.
Playing discs
Selecting the format of audio and video
You can select an audio and video format as you prefer depending on
the contents of the disc you are playing.
Switching audio soundtrack
VR
DVD-V
DVD-RW
<DVD-RW VR mode>
When playing a DVD-Video disc
recorded with two or more
soundtracks (these are often in
different languages), you can
switch them during play.
On DVD-RW discs recorded in
VR mode, you can switch main
(L), sub audio (R) or a mix of
both (L/R).
1
1
00:00:00
DVD-RW
VR Original
1 Dolby Digital Dual L/R
2 Dolby Digital 2ch ----
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
1
CH
REC
MONITOR
3
During play, press DISPLAY
button.
The display menu will appear.
Screen:
1
1
01:23:45
DVD-Video
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
1
PAUSE
SKIP
F
Select a desired audio soundtrack using K / L buttons,
then press ENTER button.
<DVD-Video>
Audio soundtrack will switch.
<DVD-RW VR mode>
1
1
00:00:00
1 Dolby Digital Dual
2 Dolby Digital 2ch
OPEN/CLOSE
DISPLAY
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
DVD-RW
VR Original
L/R
L
R
2
3
4
2
Select
icon using { / B
buttons, then press ENTER
button.
Audio menu will appear.
<DVD-Video>
1
1
00:00:00
1 Dolby Digital 5.1ch English
2 Dolby Digital 2ch Japanese
54
DVD-Video
4
Select a desired audio channel using K / L buttons, then
press ENTER button.
Audio channel will switch.
Note
• Some discs will only allow
you to change the soundtrack from the disc’s menu.
Press TOP MENU button or
MENU / LIST button to display this.
• On DVD-RW discs recorded
in VR mode that may have
both a main and a sub audio
channel, you can switch main
(L), sub audio (R), or a mix of
both (L/R).
NOTE:This unit CANNOT
record in both stereo and
SAP (Secondary Audio
Program) at the same time.
Playing discs
Before you start
Selecting the format of audio and video (cont’d)
CD
MP3
1
2
POWER
Select
icon using { / B
buttons, then press ENTER
button.
Audio menu will appear.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
1
CH
REC
MONITOR
REC
PAUSE
SKIP
F
Select a desired audio channel using K / L buttons, then
press ENTER button.
Audio channel will switch.
H
B
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
1
00:00:00
G
PLAY
REV
Audio CD
00:00:00
WXYZ
9
CM SKIP
Audio CD
{
B
RETURN
ZOOM
L
2
3
Playing discs
Switching subtitles
VR
DVD-V
DVD-RW
2
Select
icon using { / B
buttons, then press ENTER
button.
Subtitle menu will appear.
POWER
1
1
00:00:00
DVD-Video
CH
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
1
1
01:23:45
DVD-Video
{
B
RETURN
ZOOM
3
Note
• Some discs will only allow
you to change the subtitle
from the disc menu. Press
TOP MENU button or MENU
/ LIST button to display the
disc menu.
55
Español
When selecting “OFF,” subtitle will
be disappeared.
2
3
Others
Select a desired subtitle language using K / L buttons,
then press ENTER button.
Subtitle will be displayed in the
selected language.
L
Changing the SETUP menu
OFF
1 English
2 Japanese
During play, press DISPLAY
button.
The display menu will appear.
Screen:
TIMER
PROG.
A
1
REC
MONITOR
1
OPEN/CLOSE
DISPLAY
Editing
Many DVD Video discs have subtitles in one or more languages –
the case will usually tell you which
subtitle languages are available.
You can switch subtitle languages
anytime during playback.
Recording
L/R
L
R
Getting started
1
3
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
During play, press DISPLAY
button.
The display menu will appear.
Screen:
OPEN/CLOSE
DISPLAY
Connections
When playing Audio CDs or MP3
files you can switch between
stereo, just the left channel or
just the right channel.
Playing discs
Selecting the format of audio and video (cont’d)
Switching camera angles
DVD-V
Some DVD Video discs feature
scenes shot from two or more
angles–check the case for details:
it should be marked with a angle
icon if it contains multi-angle
scenes.
2
POWER
Select
icon using { / B
buttons, then press ENTER
button.
Angle will switch each you press
ENTER button.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
1
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
1
PAUSE
SKIP
F
During play, press DISPLAY
button.
The display menu will appear.
Screen:
OPEN/CLOSE
DISPLAY
H
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
1
1
01:23:45
DVD-Video
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
Angle icon appears when a switching camera angles is available.
Reducing block noise
Video
DVD-V
DVD-R
DVD-RW
POWER
1
VR
1
00:00:00
DVD-Video
DVD-RW
OFF
Type 1
Type 2
1
1
1
01:23:45
DVD-Video
Select
icon using { / B
buttons, then press ENTER
button.
NR menu will appear.
56
.@/:
1
ABC
2
CH
OPEN/CLOSE
REC
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
3
Select a desired option using
K / L buttons, then press
ENTER button.
Your setting will be activated.
2
TIMER
PROG.
A
1
REC
MONITOR
During play, press DISPLAY
button.
The display menu will appear.
Screen:
DISPLAY
This function reduces noise in the
playback picture.When playing
back discs recorded in long time
mode such as SLP or SEP mode,
select "Type 1" or "Type 2".
("Type 2" is more effective.)
When playing back discs with a
few noises such as DVD-Video
discs, select "OFF".
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
Editing
You can make the discs with editing functions following of the DVD recorder as you prefer.
Editing discs with Video mode
Title list allows you to check the titles recorded on
the disc easily.You can choose a title to play from this
screen and can easily edit the titles as you prefer.
You can edit discs with Video mode for the following
items. Be sure that once you edit titles, they will not
remain as original.
• Deleting titles (Refer to page 59)
• Putting names on titles (Refer to pages 60-61)
• Setting or clearing chapter markers (Refer to page 62)
Disc > Edit > Original
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
5
6
JAN/1 5:00AM
JAN/1 6:00AM
4
JAN/1 4:00AM
1
Note
2
7
• Once a disc is finalized, then editing the disc or
recording to the disc will not be available.
(Except DVD-RW discs in VR mode.)
• A playlist is not available with the DVD-R discs
and DVD-RW discs in Video mode.
1
JAN/1 1:00AM CH12
Recording
Disc > Edit > Original
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
XP
6
5
Playing discs
0:01:25
8 3
Getting started
1
Connections
Guide to a title list
Before you start
Information on disc editing
4
Editing
1. Titles recorded on the disc. Each can be selected to edit by pressing ENTER button with the
cursor on the title
2. Protect icon, which appears when the title has
been protected.
3. The selected title thumbnails from the title list.
4. The menus in here for editing titles as you prefer.The available menus depends on the disc
type and the format type.
5. The details of the title, which can be changed to
the title name you will edit.
6. Time status bar of the title.
7. The arrow icon, which means the title list
includes a next or a previous page. Press B or
{ button by following direction of the icon.
8. Playback status of the current disc.
Changing the SETUP menu
Others
Español
57
Editing
Information on disc editing (cont’d)
Editing discs with VR mode
For discs with VR mode, you can edit from “Original” menu or “Playlist” menu, which is created from the
original.
Editing original titles
Editing playlists
Followings are the items you can edit the original.
• Deleting titles (Refer to page 63)
• Deleting parts of titles (Refer to pages 64-65)
• Putting names on titles (Refer to pages 65-66)
• Setting or clearing chapter markers (Refer to
pages 67-68)
• Setting pictures for thumbnails (Refer to pages
68-69)
• Setting titles to protect (Refer to pages 70-71)
You can create a playlist from original titles, so that
you can edit as you prefer without losing original
titles.
Followings are the items you can edit with a
playlist.
• Deleting titles (Refer to page 72)
• Deleting parts of titles (Refer to pages 73-74)
• Putting names on titles (Refer to pages 74-75)
• Setting or clearing chapter markers (Refer to
pages 76-77)
• Setting pictures for thumbnails (Refer to pages
77-78)
• Adding titles to a playlist (Refer to page 79)
• Deleting a playlist (Refer to page 80)
Note
• Original titles once edited will not be remained as recorded originally.When you want to leave the original as it is, edit the playlist as you prefer. (Refer to pages 72-80)
58
Editing
Before you start
Editing DVD-RW discs in Video mode
Deleting titles
Video
DVD-RW
3
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Edit menu will appear.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
Disc > Edit
REC
WXYZ
9
CM SKIP
PAUSE
SKIP
F
1
H
G
B
PLAY
REV
FWD
h
g
STOP
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
JAN/ 1 1:00AM CH12
C
XP
0:01:25
Select “Title Delete” using K
/ L buttons, then press
ENTER button.
Option window will appear.
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
Playing discs
Disc > Edit
Disc Setting
1
2
Title Delete
Edit Title Name
Chapter Mark
Yes
Disc > Edit
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
No
XP
0:01:25
5
Select “Yes” using { / B buttons, then press ENTER button.
Title will be deleted.
Changing the SETUP menu
1
JAN/ 1 1:00AM CH12
Editing
Select “Edit” using K / L buttons, then press ENTER button.
Titlelist will appear.
Screen:
4
1
6
TOP MENU
5
Disc > Edit
JAN/1 4:00AM
Recording
4
SETUP
Getting started
Title Delete
Edit Title Name
Chapter Mark
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
1
OPEN/CLOSE
DISPLAY
Connections
You can delete titles which you
do not need anymore.
Be advised that the titles once
deleted cannot be brought back
to the disc.
When the last title in the title list
in Video mode is deleted, the disc
space to record will be increased.
1
JAN/1 5:00AM
Title Delete
Edit Title Name
Chapter Mark
Yes
JAN/ 1 1:00AM CH12
No
XP
Others
Writing to Disc
This operation may take a
while to be completed.
6
Español
After writing to disc is completed, press SETUP button
to exit DISC menu.
59
Editing
Editing DVD-RW discs in Video mode (cont’d)
Putting names on titles
Video
DVD-RW
You can put title names on the
titles and change the names from
this menu.
The names you put on the titles
will be displayed on a titlelist.
4
POWER
Select “Edit Title Name”
using K / L buttons, then
press ENTER button.
A window for entering a title
name will appear.
1
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
Disc > Edit > Edit Title Name
1
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
OPEN/CLOSE
DISPLAY
REC
PAUSE
SKIP
F
ABC
abc
123
@!?
5
H
G
B
PLAY
REV
FWD
h
g
STOP
C
JAN/ 1 1:00AM CH12 XP
0:01:25
SETUP
1
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
1
2
3
4
5
B
RETURN
ZOOM
L
5
To enter a title name, follow
the steps of “Guide to edit
title name” on this page.
character set
Disc Setting
2
Disc > Edit > Edit Title Name
Select “Edit” using K / L buttons, then press ENTER button.
Titlelist will appear.
Screen:
1
ABC
abc
123
@!?
JAN/ 1 1:00AM CH12 XP
0:01:25
[ Guide to edit title name ]
[Step1]: Select a desired character set using K/ L
buttons, then press
ABC
ENTER button.
abc
123
@!?
[Step2]: Press Number buttons following by the list
below.
Select
Disc > Edit
area for entering title names
1
2
1
JAN/1 1:00AM
JAN/1 2:00AM
4
JAN/1 4:00AM
JAN/1 3:00AM
5
JAN/1 5:00AM
3
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Edit menu will appear.
Disc > Edit
1
JAN/ 1 1:00AM CH12
Title Delete
Edit Title Name
Chapter Mark
XP
0:01:25
60
0
3
When you finish entering a title
name, press ENTER button.
ABC
abc
123
@!?
<space>
<space>
0
<space>
1
!”#$%
&‘ ( ) *
+ ,- ./ :;
<=>?
@[]^
_{|}
Press
1
2
ABC
abc
2
3
DEF
def
3
4
GHI
ghi
4
5
6
JKL
jkl
5
MNO
mno
6
7
8
PQRS
pqrs
7
TUV
tuv
8
9
WXYZ
wxyz
9
* Press 1 button, character set will be changed
to the " @!? " mode automatically.
・To delete letters, press CLEAR button repeatedly.
Holding CLEAR button to delete all letters.
・To go on to the next entering area for letters,
press B button.
・You can enter up to 30 letters.
Editing
Before you start
Editing DVD-RW discs in Video mode (cont’d)
6
POWER
Select “Yes” using { / B buttons, then press ENTER button.
The name you entered will be
activated for the title.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
CH
REC
MONITOR
Disc > Edit > Edit Title Name
WXYZ
9
CM SKIP
PAUSE
SKIP
F
ABC
abc
123
@!?
H
G
B
PLAY
REV
FWD
h
g
STOP
C
Yes
No
abc
Writing to Disc
7
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
6
Recording
This operation may take a
while to be completed.
Getting started
REC
TUV
8
SPACE
0
PQRS
7
Connections
A
REC SPEED CLEAR
1
OPEN/CLOSE
DISPLAY
7
Playing discs
After writing to disc is completed, press SETUP button
to exit DISC menu.
Editing
Changing the SETUP menu
Others
Español
61
Editing
Editing DVD-RW discs in Video mode (cont’d)
Setting or clearing chapter markers
Video
DVD-RW
You can put chapter markers in
each title. Once a chapter is
marked, you can use it for the
chapter search feature.
You can set chapter markers at a
specified time you selected for
titles with more than 5 minutes.
Disc > Edit
POWER
1
Title Delete
Edit Title Name
Chapter Mark
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
JAN/ 1 1:00AM CH12
REC
MONITOR
XP
0:01:25
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
REC
PAUSE
SKIP
F
1
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
4
H
G
B
PLAY
REV
Select “Chapter Mark” using
K / L buttons, then press
ENTER button.
Option window will appear.
1
JAN/ 1 1:00AM CH12
FWD
h
g
STOP
C
1
7
Disc > Edit
Disc Setting
OPEN/CLOSE
DISPLAY
Title Delete
OFF
Edit Title5Name
minutes
Chapter
10Mark
minutes
15 minutes
30 minutes
60 minutes
XP
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
6
0:01:25
2
5
Select “Edit” using K / L buttons, then press ENTER button.
Titlelist will appear.
Screen:
Select a desired time using K
/ L buttons, then press
ENTER button.
Option window will appear.
Disc > Edit
Disc > Edit
1
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
Title Delete
OFF
Edit Title5Name
minutes
Chapter
10Mark
minutes
15 minutes
30 minutes
60 minutes
Yes
4
No
5
JAN/ 1 1:00AM CH12
XP
0:01:25
JAN/1 4:00AM
JAN/1 5:00AM
3
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Edit menu will appear.
6
Select “Yes” using { / B buttons, then press ENTER button.
A chapter marker will be added.
7
After writing to disc is completed, press SETUP button
to exit DISC menu.
62
Note
• You cannot select a time for
putting markers beyond a
length of a title.
• A chapter marker may be
delayed according to the
recording content.
Editing
Before you start
Editing DVD-RW discs in VR mode (Original)
Deleting titles
Deleting titles
VR
DVD-RW
4
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
CH
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
JAN/ 1 1:00AM CH12
C
XP
0:01:25
Select “Title Delete” using K
/ L buttons, then press
ENTER button.
Option window will appear.
Disc Setting
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
6
Playing discs
Disc > Edit > Original
2
1
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Protect OFF ON
Yes
JAN/ 1 1:00AM CH12
No
XP
0:01:25
Editing
6
Disc > Edit
Changing the SETUP menu
Select “Yes” using { / B buttons, then press ENTER button.
Title will be deleted.
Original
Disc > Edit > Original
1
3
No
XP
Writing to Disc
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
7
Español
1
2
JAN/1 4:00AM
Yes
JAN/ 1 1:00AM CH12
This operation may take a
while to be completed.
1
4
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Protect OFF ON
Others
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
Disc > Edit > Original
Recording
5
1
7
Getting started
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
.@/:
1
REC SPEED CLEAR
Disc > Edit > Original
1
TIMER
PROG.
A
REC
MONITOR
1
OPEN/CLOSE
DISPLAY
Connections
When a title is deleted from an
original list in VR mode, the disc
space to record will be increased.
Be advised that the titles once
deleted cannot be brought back
to the disc.
After writing to disc is completed, press SETUP button
to exit DISC menu.
5
JAN/1 5:00AM
.
63
Editing
Editing DVD-RW discs in VR mode (Original) (cont’d)
Deleting parts of titles
VR
DVD-RW
You can delete part of a title, the
disc space to record will be
increased.
Be advised that the parts once
deleted cannot be brought back
to the disc.
4
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
CH
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Disc > Edit > Original
1
TIMER
PROG.
A
REC
MONITOR
1
PAUSE
SKIP
F
H
B
FWD
g
STOP
JAN/ 1 1:00AM CH12
C
XP
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
5
L
Select “Scene Delete” using
K / L buttons, then press
ENTER button.
Option window will appear.
2
Disc > Edit > Original
1
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
JAN/ 1 1:00AM CH12
Title Delete
Scene Delete
Start
Edit Title Name
End
Chapter Mark
Preview
Index Picture
Delete
Protect OFF
XP
0:00:55
Disc > Edit
6
Press ENTER button to
decide a start point, then
press ENTER button to
decide an end point.
A cursor will move to “Preview.”
You can check a preview.
Original
3
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
Disc > Edit > Original
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
<Preview>
Before
editing
5
Edited
JAN/1 4:00AM
64
JAN/1 5:00AM
G
PLAY
REV
h
0:01:25
Disc Setting
OPEN/CLOSE
DISPLAY
Start point End point
1
2
3
4
5
6
Editing
Before you start
Editing DVD-RW discs in VR mode (Original) (cont’d)
8
Select “Delete” using K / L
buttons, then press ENTER
button.
Option window will appear.
Select “Yes” using { / B buttons, then press ENTER button.
Part of a title will be deleted.
POWER
1
CH
JAN/ 1 1:00AM CH12
No
Title Delete
Scene Delete
Start
Edit Title Name
End
Chapter Mark
Preview
Index Picture
Delete
Protect OFF
Yes
JAN/ 1 1:00AM CH12
XP
0:01:25
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
REC
WXYZ
9
CM SKIP
PAUSE
SKIP
F
H
G
B
PLAY
REV
No
FWD
h
g
STOP
C
XP
Writing to Disc
TUV
8
SPACE
0
PQRS
7
9
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
L
7
8
9
Playing discs
After writing to disc is completed, press SETUP button
to exit DISC menu.
Putting names on titles
VR
DVD-RW
POWER
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
A
CH
REC
MONITOR
REC
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
Disc > Edit
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
OPEN/CLOSE
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
Original
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Others
1
2
Changing the SETUP menu
1
2
Editing
You can put title names on the
titles and change the names from
this menu.
The names you put on the titles
will be displayed on a titlelist.
Recording
This operation may take a
while to be completed.
ZOOM
Getting started
Yes
1
.@/:
1
REC SPEED CLEAR
Disc > Edit > Original
Title Delete
Scene Delete
Start
Edit Title Name
End
Chapter Mark
Preview
Index Picture
Delete
Protect OFF
TIMER
PROG.
A
REC
MONITOR
Disc > Edit > Original
OPEN/CLOSE
DISPLAY
Connections
7
Disc Setting
Español
65
Editing
Editing DVD-RW discs in VR mode (Original) (cont’d)
3
6
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
To enter a title name, follow
the steps of “Guide to edit
title name” on this page.
character set
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
CH
REC
MONITOR
1
2
1
JAN/1 1:00AM
JAN/1 2:00AM
ABC
abc
123
@!?
1
3
JAN/1 3:00AM
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Disc > Edit > Original > Edit Title Name
Disc > Edit > Original
OPEN/CLOSE
DISPLAY
REC
PAUSE
6
SKIP
F
H
G
B
PLAY
4
REV
5
FWD
h
g
STOP
C
JAN/ 1 1:00AM CH12 XP
JAN/1 4:00AM
JAN/1 5:00AM
0:01:25
SETUP
8
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
Disc > Edit > Original
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
ENTER
REPEAT
{
3
4
5
6
7
B
RETURN
ZOOM
L
7
Select “Yes” using { / B buttons, then press ENTER button.
The name you entered will be
activated for the title.
Disc > Edit > Original > Edit Title Name
JAN/ 1 1:00AM CH12
MENU/LIST
K
area for entering title names
When you finish entering a title
name, press ENTER button.
4
TOP MENU
XP
1
0:01:25
ABC
abc
123
@!?
[ Guide to edit title name ]
[Step1]: Select a desired character set using K/ L
buttons, then press
ABC
ENTER button.
abc
123
@!?
[Step2]: Press Number buttons following by the list
below.
Select
Yes
5
No
abc
Select “Edit Title Name”
using K / L buttons, then
press ENTER button.
A window for entering a title
name will appear.
Disc > Edit > Original > Edit Title Name
1
ABC
abc
123
@!?
ABC
abc
123
@!?
<space>
<space>
0
<space>
1
!”#$%
&‘ ( ) *
+ ,- ./ :;
<=>?
@[]^
_{|}
Press
0
Writing to Disc
1
This operation may take a
while to be completed.
8
After writing to disc is completed, press SETUP button
to exit DISC menu.
2
ABC
abc
2
3
DEF
def
3
4
GHI
ghi
4
5
6
JKL
jkl
5
MNO
mno
6
7
8
PQRS
pqrs
7
TUV
tuv
8
9
WXYZ
wxyz
9
* Press 1 button, character set will be changed
to the " @!? " mode automatically.
JAN/ 1 1:00AM CH12 XP
0:01:25
66
・To delete letters, press CLEAR button repeatedly.
Holding CLEAR button to delete all letters.
・To go on to the next entering area for letters,
press B button.
・You can enter up to 30 letters.
Editing
Before you start
Editing DVD-RW discs in VR mode (Original) (cont’d)
Setting or clearing chapter markers
VR
DVD-RW
3
JAN/1 2:00AM
4
JAN/1 3:00AM
CH
5
JAN/1 5:00AM
REC
DEF
3
GHI
4
JKL
5
MNO
6
4
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
PAUSE
SKIP
H
G
B
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
PLAY
REV
FWD
h
g
STOP
C
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Disc > Edit > Original
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
XP
1
2
3
4
5
6
5
Select “Chapter Mark” using
K / L buttons, then press
ENTER button.
Option window will appear.
Editing
Disc > Edit > Original
1
Chapter 1/1
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
Delete
Index Picture
Protect OFF ON
Changing the SETUP menu
Disc > Edit
JAN/ 1 1:00AM CH12
XP
0:01:25
6
Original
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
Select “Add” or “Delete”
using K / L buttons, then
press ENTER button.
Option window will appear.
<Add>:
Others
3
Playing discs
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
ABC
2
F
0:01:25
2
.@/:
1
REC SPEED CLEAR
JAN/ 1 1:00AM CH12
Disc Setting
TIMER
PROG.
A
REC
MONITOR
JAN/1 4:00AM
OPEN/CLOSE
DISPLAY
Recording
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
JAN/1 1:00AM
POWER
1
2
1
Getting started
1
Disc > Edit > Original
Connections
You can put chapter markers in
each title. Once a chapter is
marked, you can use it for the
chapter search feature.
You can put a chapter marker
anywhere you want.
When the number of chapter
markers in the original list comes
to 999 in total, you cannot add
any more chapter markers.
Disc > Edit > Original
1
Chapter 1/1
Español
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
Delete
Index Picture
Protect OFF ON
F
Yes
JAN/ 1 1:00AM CH12
No
XP
0:01:25
67
Editing
Editing DVD-RW discs in VR mode (Original) (cont’d)
<Delete>:
The chapter marker which you
selected will be deleted.
<Delete>:
Disc > Edit > Original
1
Chapter 2/2
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
Delete
Index Picture
Protect OFF ON
JAN/ 1 1:00AM CH12
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
Disc > Edit > Original
1
F
Yes
POWER
No
Chapter 2/2
XP
0:01:25
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
Delete
Index Picture
Protect OFF ON
Yes
JAN/ 1 1:00AM CH12
• You cannot delete the first
chapter marker of each title.
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
No
XP
REC
Writing to Disc
DEF
3
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
7
Select “Yes” using { / B buttons, then press ENTER button.
A chapter marker will be added.
<Add>:
Disc > Edit > Original
1
Chapter 1/1
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
Delete
Index Picture
Protect OFF ON
Yes
JAN/ 1 1:00AM CH12
This operation may take a
while to be completed.
REV
FWD
h
g
STOP
C
SETUP
8
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
8
B
RETURN
ZOOM
7
L
After writing to disc is completed, press SETUP button
to exit DISC menu.
No
XP
Writing to Disc
This operation may take a
while to be completed.
Setting pictures for thumbnails
VR
DVD-RW
You can set a picture to each title
for a thumbnail. It helps you to
remember the contents of the
title you are playing.The beginning picture has been selected as
the default.
2
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
Disc > Edit
1
OPEN/CLOSE
DISPLAY
PAUSE
SKIP
F
H
G
B
PLAY
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
REV
FWD
h
g
STOP
C
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
Original
B
RETURN
ZOOM
L
1
2
Note
Disc Setting
68
• If a selected picture for a
thumbnail is deleted by deleting a part of a title, a default
picture will be selected.
Editing
Before you start
Editing DVD-RW discs in VR mode (Original) (cont’d)
6
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
Select “Yes” using { / B buttons, then press ENTER button.
A picture for thumbnail will be
set.
POWER
1
2
CH
REC
MONITOR
REC
Disc > Edit > Original
3
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
JAN/1 3:00AM
5
No
JAN/1 5:00AM
JAN/ 1 1:00AM CH12
SPACE
0
PAUSE
XP
H
PLAY
REV
FWD
h
g
STOP
C
7
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
JAN/ 1 1:00AM CH12
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
After writing to disc is completed, press SETUP button
to exit DISC menu.
Playing discs
Disc > Edit > Original
7
3
4
5
6
Recording
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
This operation may take a
while to be completed.
G
B
Writing to Disc
4
CM SKIP
SKIP
F
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
Yes
JAN/1 4:00AM
ABC
2
Getting started
JAN/1 2:00AM
4
.@/:
1
REC SPEED CLEAR
1
JAN/1 1:00AM
TIMER
PROG.
A
Disc > Edit > Original
1
OPEN/CLOSE
DISPLAY
Connections
3
XP
0:01:25
Editing
5
Changing the SETUP menu
Select “Index Picture Set”
using K / L buttons, then
press ENTER button.
Option window will appear.
Disc > Edit > Original
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
F
Yes
JAN/ 1 1:00AM CH12
No
XP
Others
0:01:25
Español
69
Editing
Editing DVD-RW discs in VR mode (Original) (cont’d)
Setting titles to protect
VR
DVD-RW
To prevent accidental editing, or
erasing the titles, you can protect
them from the original menu.
1
4
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
CH
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
Disc > Edit > Original
1
TIMER
PROG.
A
REC
MONITOR
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
OPEN/CLOSE
DISPLAY
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
REC
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
JAN/ 1 1:00AM CH12
C
XP
0:01:25
5
Select “Protect OFF ➔ ON”
using K / L buttons, then
press ENTER button.
Option window will appear.
Disc Setting
2
Disc > Edit > Original
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
Yes
JAN/ 1 1:00AM CH12
No
XP
0:01:25
Disc > Edit
6
Select “Yes” using { / B buttons, then press ENTER button.
Disc > Edit > Original
Original
1
3
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
Disc > Edit > Original
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
JAN/1 4:00AM
5
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
Yes
JAN/ 1 1:00AM CH12
No
XP
Writing to Disc
This operation may take a
while to be completed.
7
After writing to disc is completed, press SETUP button
to exit DISC menu.
JAN/1 5:00AM
To protect a whole disc
(DVD-RW VR mode Only):
Select “Disc Protect” from Disc
menu, then select “Yes”.
70
1
7
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
6
Editing
Before you start
Editing DVD-RW discs in VR mode (Original) (cont’d)
Releasing titles from protecting
VR
DVD-RW
1
4
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Original menu will appear.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
REC
MONITOR
REC SPEED CLEAR
Disc Edit > Original
2
TIMER
PROG.
REC
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect ON OFF
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
JAN/ 1 2:00AM CH12
XP
0:01:25
Select “Protect ON ➔ OFF”
using K / L buttons, then
press ENTER button.
Option window will appear.
Disc Setting
2
Disc Edit > Original
2
B
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
6
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect ON OFF
Yes
JAN/ 1 2:00AM CH12
TOP MENU
No
Playing discs
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
SETUP
Recording
5
1
7
Getting started
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
OPEN/CLOSE
DISPLAY
Connections
You are allowed to release the
titles once protected from protecting.
XP
0:01:25
Disc > Edit
Editing
6
3
Changing the SETUP menu
Select “Yes” using { / B buttons, then press ENTER button.
Original
Disc Edit > Original
2
Select “Original” using { / B
buttons, then press ENTER
button.
Original list will appear.
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect ON OFF
Yes
JAN/ 1 2:00AM CH12
No
XP
Writing to Disc
Others
Disc > Edit > Original
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
JAN/1 4:00AM
This operation may take a
while to be completed.
5
JAN/1 5:00AM
7
Español
After writing to disc is completed, press SETUP button
to exit DISC menu.
71
Editing
Editing DVD-RW discs in VR mode (Playlist)
Deleting titles
VR
DVD-RW
In VR mode, even when a title is
deleted from a Playlist, the original
title will remain in an Original list.
The disc space to record will not
be increased.
4
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
1
1
JAN/ 1 1:00AM CH12
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
XP
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Yes
JAN/ 1 1:00AM CH12
No
XP
0:01:25
6
Select “Yes” using { / B buttons, then press ENTER button.
Title will be deleted.
Disc > Edit > Playlist
Original
1
3
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Yes
JAN/ 1 1:00AM CH12
No
XP
Writing to Disc
This operation may take a
while to be completed.
Disc > Edit > Playlist
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
JAN/1 4:00AM
5
JAN/1 5:00AM
Add New
Title
Delete
Playlist
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC
SPACE
0
PAUSE
CM SKIP
SKIP
F
H
G
B
PLAY
FWD
g
C
1
1
2
GHI
4
STOP
2
1
DEF
3
h
Disc > Edit > Playlist
Select “PlayList” using { / B
buttons, then press ENTER
button.
Playlist will appear.
ABC
2
REV
/ L buttons, then press
ENTER button.
Option window will appear.
Disc > Edit
.@/:
1
REC SPEED CLEAR
5
Select “Title Delete” using K
72
CH
REC
MONITOR
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
0:01:25
Disc Setting
TIMER
PROG.
A
Disc > Edit > Playlist
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
OPEN/CLOSE
DISPLAY
7
After writing to disc is completed, press SETUP button
to exit DISC menu.
1
7
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
6
Editing
Before you start
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Deleting parts of titles
VR
DVD-RW
4
POWER
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
.@/:
1
ABC
2
DEF
3
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
REC
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
SPACE
0
PAUSE
F
H
G
B
PLAY
REV
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
CM SKIP
SKIP
FWD
h
g
STOP
C
JAN/ 1 1:00AM CH12
XP
0:01:25
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Select “Scene Delete” using
K / L buttons, then press
ENTER button.
Option window will appear.
Disc Setting
1
2
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
JAN/ 1 1:00AM CH12
Title Delete
Scene Delete
Start
Edit Title Name
End
Chapter Mark
Preview
Index Picture
Delete
XP
0:00:55
Editing
6
Disc > Edit
Changing the SETUP menu
Press ENTER button to
decide a start point, then
press ENTER button to
decide an end point.
A cursor will move to “Preview”.
You can check a preview.
Original
3
Select “PlayList” using { / B
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
Add New
Title
Delete
Playlist
Español
JAN/1 4:00AM
5
Start point End point
Before
editing
Disc > Edit > Playlist
4
<Preview>
Others
buttons, then press ENTER
button.
Playlist will appear.
Playing discs
Disc > Edit > Playlist
Recording
5
1
2
3
4
5
6
Getting started
1
TIMER
PROG.
A
Disc > Edit > Playlist
1
OPEN/CLOSE
DISPLAY
Connections
You can delete a specified part of
a title.
Even when a title is deleted from
the playlist, the original title will
remain.
The disc space to record will not
be increased.
Edited
JAN/1 5:00AM
73
Editing
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Part of a title will be deleted.
POWER
7
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
Disc > Edit > Playlist
Select “Delete” using K / L
buttons, then press ENTER
button.
Option window will appear.
Title Delete
Scene Delete
Start
Edit Title Name
End
Chapter Mark
Preview
Index Picture
Delete
1
Yes
JAN/ 1 1:00AM CH12
CH
REC
MONITOR
No
MNO
6
WXYZ
9
REC
SPACE
0
PAUSE
0:01:25
H
PLAY
This operation may take a
while to be completed.
REV
g
STOP
C
9
9
FWD
h
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
After writing to disc is completed, press SETUP button
to exit DISC menu.
8
G
B
No
XP
CM SKIP
SKIP
F
Title Delete
Scene Delete
Start
Edit Title Name
End
Chapter Mark
Preview
Index Picture
Delete
Yes
JAN/ 1 1:00AM CH12
JKL
5
TUV
8
REC SPEED CLEAR
Disc > Edit > Playlist
1
GHI
4
PQRS
7
XP
Writing to Disc
DEF
3
7
8
Select “Yes” using { / B buttons, then press ENTER button.
Putting names on titles
VR
DVD-RW
Screen:
You can put title names on the
titles and change the names from
this menu.
The names you put on the titles
will be displayed on a titlelist.
POWER
Disc > Edit
.@/:
1
ABC
2
DEF
3
CH
GHI
4
JKL
5
MNO
6
Original
REC
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
PAUSE
SKIP
H
G
B
PLAY
REV
3
FWD
h
g
STOP
C
Disc > Edit > Playlist
2
WXYZ
9
CM SKIP
F
Select “PlayList” using { / B
buttons, then press ENTER
button.
Playlist will appear.
Disc Setting
TUV
8
SPACE
0
PQRS
7
REC SPEED CLEAR
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
74
TIMER
PROG.
A
REC
MONITOR
1
OPEN/CLOSE
DISPLAY
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
JAN/1 4:00AM
5
JAN/1 5:00AM
Add New
Title
Delete
Playlist
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
Editing
Before you start
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
7
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
Select “Yes” using { / B buttons, then press ENTER button.
The name you entered will be
activated for the title.
POWER
1
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
REC
MONITOR
REC SPEED CLEAR
Disc > Edit > Playlist
REC
Disc > Edit > Playlist > Edit Title Name
1
SPACE
0
PAUSE
F
ABC
abc
123
@!?
CM SKIP
SKIP
H
G
B
PLAY
REV
FWD
h
g
STOP
C
JAN/ 1 1:00AM CH12
XP
Yes
0:01:25
No
abc
SETUP
8
TOP MENU
MENU/LIST
K
{
B
RETURN
ZOOM
L
5
Select “Edit Title Name”
using K / L buttons, then
press ENTER button.
A window for entering a title
name will appear.
1
ABC
abc
123
@!?
JAN/ 1 1:00AM CH12 XP
0:01:25
8
After writing to disc is completed, press SETUP to exit
DISC menu.
[ Guide to edit title name ]
[Step1]: Select a desired character set using K/ L
buttons, then press
ABC
ENTER button.
abc
123
@!?
[Step2]: Press Number buttons following by the list
below.
abc
123
@!?
0
<space>
<space>
0
<space>
1
!”#$%
&‘ ( ) *
+ ,- ./ :;
<=>?
@[]^
_{|}
To enter a title name, follow
the steps of “Guide to edit
title name” on this page.
character set
Disc > Edit > Playlist > Edit Title Name
1
ABC
abc
123
@!?
1
2
ABC
abc
2
3
DEF
def
3
4
GHI
ghi
4
5
6
JKL
jkl
5
MNO
mno
6
7
8
PQRS
pqrs
7
TUV
tuv
8
9
WXYZ
wxyz
9
JAN/ 1 1:00AM CH12 XP
0:01:25
area for entering title names
・To delete letters, press CLEAR button repeatedly.
Holding CLEAR button to delete all letters.
・To go on to the next entering area for letters,
press B button.
・You can enter up to 30 letters.
Español
When you finish entering a title
name, press ENTER button.
Others
* Press 1 button, character set will be changed
to the " @!? " mode automatically.
Changing the SETUP menu
ABC
Editing
Select
Press
6
Playing discs
Disc > Edit > Playlist > Edit Title Name
This operation may take a
while to be completed.
Recording
4
5
6
7
ENTER
REPEAT
Writing to Disc
Getting started
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
OPEN/CLOSE
DISPLAY
Connections
4
75
Editing
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Setting or clearing chapter markers
VR
DVD-RW
You can put chapter markers in
each title. Once a chapter is
marked, you can use it for the
chapter search feature.
You can put a chapter marker
anywhere you want.
When the number of chapter
markers in the playlist comes to
999 in total, you cannot add any
more chapter markers.
1
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
Disc > Edit > Playlist
JAN/1 1:00AM
POWER
1
2
1
JAN/1 2:00AM
JAN/1 4:00AM
JAN/1 3:00AM
Add New
Title
Delete
Playlist
5
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
REC
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
PAUSE
CM SKIP
SKIP
H
G
PLAY
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Playlist menu will appear.
REV
FWD
h
g
STOP
C
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Disc > Edit > Playlist
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
XP
5
Select “Chapter Mark” using
K / L buttons, then press
ENTER button.
Option window will appear.
Disc > Edit > Playlist
1
Chapter 1/1
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
DeleteSet
Index Picture
XP
6
Select “Add” or “Delete”
using K / L buttons, then
press ENTER button.
Option window will appear.
<Add>:
Disc > Edit > Playlist
1
Chapter 1/1
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
DeleteSet
Index Picture
F
Yes
JAN/ 1 1:00AM CH12
No
XP
0:01:25
76
GHI
4
B
0:01:25
Select “PlayList” using { / B
buttons, then press ENTER
button.
Playlist will appear.
DEF
3
F
JAN/ 1 1:00AM CH12
3
ABC
2
4
Disc > Edit
Original
.@/:
1
REC SPEED CLEAR
0:01:25
2
REC
MONITOR
JAN/1 5:00AM
JAN/ 1 1:00AM CH12
Disc Setting
TIMER
PROG.
A
CH
4
OPEN/CLOSE
DISPLAY
3
1
2
3
4
5
6
Editing
Before you start
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
<Delete>:
The chapter marker which you
selected will be deleted.
<Delete>:
Disc > Edit > Playlist
1
JAN/ 1 1:00AM CH12
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
Disc > Edit > Playlist
1
F
Yes
POWER
No
Chapter 2/2
XP
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
DeleteSet
Index Picture
CH
REC
MONITOR
0:01:25
Yes
JAN/ 1 1:00AM CH12
No
REC SPEED CLEAR
SPACE
0
XP
REC
Writing to Disc
PAUSE
CM SKIP
SKIP
F
H
G
B
7
PLAY
Select “Yes” using { / B buttons, then press ENTER button.
A chapter marker will be added.
<Add>:
1
Chapter 1/1
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
DeleteSet
Index Picture
Yes
JAN/ 1 1:00AM CH12
FWD
h
g
STOP
C
SETUP
8
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
8
B
RETURN
ZOOM
7
L
After writing to disc is completed, press SETUP button
to exit DISC menu.
Recording
Disc > Edit > Playlist
REV
This operation may take a
while to be completed.
Getting started
• You cannot delete the first
chapter of each title.
Connections
Chapter 2/2
Title Delete
Scene Delete
Edit Title Name
ChapterAdd
Mark
DeleteSet
Index Picture
No
XP
Playing discs
Writing to Disc
This operation may take a
while to be completed.
Setting pictures for thumbnails
2
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
A
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
REC
DEF
3
PQRS
7
PAUSE
SKIP
F
Disc > Edit
1
OPEN/CLOSE
Changing the SETUP menu
You can set a picture to each title
for a thumbnail. It helps you to
remember the contents of the
title you are playing.The beginning picture has been selected as
the default.
POWER
Editing
VR
DVD-RW
H
G
B
PLAY
REV
FWD
h
g
STOP
1
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
Original
1
2
Others
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
C
Note
77
Español
Disc Setting
• If a selected picture for a
thumbnail is deleted by deleting a part of a title, a default
picture will be selected.
Editing
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
3
6
Select “PlayList” using { / B
buttons, then press ENTER
button.
Playlist will appear.
Select “Yes” using { / B buttons, then press ENTER button.
A picture for thumbnail will be
set.
POWER
1
2
CH
REC
MONITOR
JAN/1 3:00AM
Add New
Title
Delete
Playlist
5
REC
Disc > Edit > Playlist
3
JAN/1 2:00AM
4
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
PAUSE
H
JAN/ 1 1:00AM CH12
PLAY
REV
FWD
h
g
STOP
No
XP
7
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
Writing to Disc
{
B
RETURN
ZOOM
L
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Playlist menu will appear
Disc > Edit > Playlist
1
JAN/ 1 1:00AM CH12
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
XP
0:01:25
.
5
Select “Index Picture Set”
using K / L buttons, then
press ENTER button.
Option window will appear.
Disc > Edit > Playlist
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
F
Yes
JAN/ 1 1:00AM CH12
No
XP
0:01:25
78
G
B
C
JAN/1 5:00AM
4
CM SKIP
SKIP
F
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Yes
JAN/1 4:00AM
.@/:
1
REC SPEED CLEAR
1
JAN/1 1:00AM
TIMER
PROG.
A
Disc > Edit > Playlist
1
OPEN/CLOSE
DISPLAY
This operation may take a
while to be completed.
7
After writing to disc is completed, press SETUP button
to exit DISC menu.
3
4
5
6
Editing
Before you start
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Adding titles to a Playlist
VR
DVD-RW
4
POWER
Select “Add New Title” using
K / L / { / B buttons, then
press ENTER button.
Original list will appear.
1
1
2
1
CH
REC
MONITOR
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
REC SPEED CLEAR
REC
3
SPACE
0
PAUSE
JAN/12 5:00PM
H
G
B
JAN/12 8:00PM
PLAY
REV
FWD
h
g
STOP
C
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Disc > Edit > Playlist > Add New Title
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
Playing discs
2
TOP MENU
Recording
5
SETUP
Getting started
JAN/10 10:30AM
CM SKIP
SKIP
F
1
6
Disc Setting
TIMER
PROG.
A
Disc > Edit > Playlist > Add New Title
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
OPEN/CLOSE
DISPLAY
Connections
You can add or delete a title in
the playlist as you prefer.
You can add titles to a Playlist up
to 99.
58%
Writing to Disc
Disc > Edit
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
5
6
4
JAN/1 4:00AM
3
Disc > Edit > Playlist
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
Add New
Title
Delete
Playlist
6
After writing to disc is completed, press SETUP button
to exit DISC menu.
To delete a title from Playlist,
refer to “Deleting titles” on page
72.
To delete a Playlist, refer to
“Deleting a Playlist” on page 80.
Español
JAN/1 4:00AM
5
JAN/12 8:00PM
Others
Select “PlayList” using { / B
buttons, then press ENTER
button.
Playlist will appear.
JAN/1 5:00AM
Changing the SETUP menu
Original
Editing
Disc > Edit > Playlist
JAN/1 5:00AM
79
Editing
Editing DVD-RW discs in VR mode (Playlist) (cont’d)
Deleting a Playlist
VR
DVD-RW
A Playlist can be deleted if you
no longer needed.
1
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
4
POWER
Select “Delete Playlist” using
K / L / { / B buttons, then
press ENTER button.
Option window will appear.
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
REC
MONITOR
REC SPEED CLEAR
Disc > Edit > Playlist
1
1
2
REC
3
SPACE
0
PAUSE
JAN/1 2:00AM
H
JAN/1 4:00AM
5
JAN/1 5:00AM
JAN/1 3:00AM
PLAY
No
C
1
6
Select “Yes” using { / B buttons, then press ENTER button.
A Playlist will be erased.
2
Select “Edit” using K / L buttons, then press ENTER button.
Original/PlayList menu will appear.
Screen:
g
STOP
5
Disc Setting
FWD
h
Add New
Title
Delete
Playlist
Yes
G
B
REV
4
CM SKIP
SKIP
F
JAN/1 1:00AM
OPEN/CLOSE
DISPLAY
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
Disc > Edit > Playlist
Add New
Title
Delete
Playlist
Disc > Edit
6
After writing to disc is completed, press SETUP button
to exit DISC menu.
Original
3
Select “PlayList” using { / B
buttons, then press ENTER
button.
Playlist will appear.
Disc > Edit > Playlist
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
4
JAN/1 4:00AM
5
JAN/1 5:00AM
Add New
Title
Delete
Playlist
Note
• Deleting a Playlist will not
increase the available recording time.
80
Editing
Before you start
Editing DVD-R discs
Deleting titles
DVD-R
Disc > Edit
1
Title Delete
Edit Title Name
Chapter Mark
POWER
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
A
CH
JAN/ 1 1:00AM CH12
XP
REC
MONITOR
0:01:25
REC SPEED CLEAR
You cannot select “Chapter Mark”.
REC
SPACE
0
PAUSE
4
G
PLAY
REV
FWD
h
Select “Title Delete” using K
/ L buttons, then press
ENTER button.
Option window will appear.
1
Title Delete
Edit Title Name
Chapter Mark
Yes
JAN/ 1 1:00AM CH12
No
XP
g
STOP
C
1
6
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
1
2
3
4
5
2
5
Select “Yes” using { / B buttons, then press ENTER button.
Title will be deleted.
Editing
Select “Edit” using K / L buttons, then press ENTER button.
Titlelist will appear.
Screen:
Playing discs
0:01:25
Disc > Edit
Disc > Edit
1
1
2
3
JAN/1 1:00AM
JAN/1 2:00AM
JAN/1 3:00AM
Title Delete
Edit Title Name
Chapter Mark
Yes
4
Changing the SETUP menu
1
No
5
JAN/ 1 1:00AM CH12
XP
Writing to Disc
JAN/1 4:00AM
JAN/1 5:00AM
3
This operation may take a
while to be completed.
6
Others
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Edit menu will appear.
Recording
Disc > Edit
Disc Setting
H
B
Getting started
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
CM SKIP
SKIP
F
1
OPEN/CLOSE
DISPLAY
Connections
You can delete titles which you
do not need, however the disc
space to record will not be
changed.
Be sure to know that the titles
once deleted cannot be brought
back to the disc.
After writing to disc is completed, press SETUP button
to exit DISC menu.
Español
81
Editing
Editing DVD-R discs (cont’d)
Putting names on titles
DVD-R
You can put title names on the
titles and change the names from
this menu.
The names you put on the titles
will be displayed on a titlelist.
4
Select “Edit Title Name”
POWER
1
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
CH
REC
MONITOR
REC SPEED CLEAR
Disc > Edit > Edit Title Name
Press SETUP button. Select
“DISC” using { / B buttons,
then press ENTER button.
SETUP/DISC menu will appear.
TIMER
PROG.
A
using K / L buttons, then
press ENTER button.
A window for entering a title
name will appear.
1
OPEN/CLOSE
DISPLAY
REC
ABC
abc
123
@!?
SPACE
0
PAUSE
5
CM SKIP
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
JAN/ 1 1:00AM CH12 XP
0:01:25
5
To enter a title name, follow
SETUP
1
7
TOP MENU
MENU/LIST
K
1
2
3
4
5
6
ENTER
REPEAT
{
B
RETURN
ZOOM
L
the steps of “Guide to edit
title name” on this page.
character set
Disc Setting
Disc > Edit > Edit Title Name
2
ABC
abc
123
@!?
1
Select “Edit” using K / L buttons, then press ENTER button.
Titlelist will appear.
Screen:
Disc > Edit
1
2
1
JAN/1 1:00AM
JAN/1 2:00AM
4
JAN/1 4:00AM
3
JAN/1 3:00AM
5
[ Guide to edit title name ]
JAN/ 1 1:00AM CH12 XP
0:01:25
area for entering title names
When you finish entering a title
name, press ENTER button.
3
Disc > Edit > Edit Title Name
Select a desired title using K /
L / { / B buttons, then press
ENTER button.
Edit menu will appear.
1
ABC
abc
123
@!?
Yes
Select
No
abc
ABC
abc
123
@!?
<space>
<space>
0
<space>
1
!”#$%
&‘ ( ) *
+ ,- ./ :;
<=>?
@[]^
_{|}
Press
1
2
ABC
abc
2
3
DEF
def
3
4
GHI
ghi
4
5
6
JKL
jkl
5
MNO
mno
6
7
8
PQRS
pqrs
7
TUV
tuv
8
9
WXYZ
wxyz
9
* Press 1 button, character set will be changed
to the " @!? " mode automatically.
Writing to Disc
Disc > Edit
1
JAN/ 1 1:00AM CH12
Title Delete
Edit Title Name
Chapter Mark
XP
0:01:25
You cannot select “Chapter Mark”.
82
123
@!?
[Step2]: Press Number buttons following by the list
below.
0
6
Select “Yes” using { / B buttons, then press ENTER button.
JAN/1 5:00AM
[Step1]: Select a desired character set using K/ L
buttons, then press
ABC
ENTER button.
abc
This operation may take a
while to be completed.
7
After writing to disc is completed, press SETUP button
to exit DISC menu.
・To delete letters, press CLEAR button repeatedly.
Holding CLEAR button to delete all letters.
・To go on to the next entering area for letters,
press B button.
・You can enter up to 30 letters.
Changing the SETUP menu
Before you start
Tour of the SETUP menu
The following table is the contents which you can set and the default settings.
Refer to the following table for useful operation.
SETUP menu
Original
English
French
Set the language for audio.
Subtitle Language
OFF
English
French
Set the language for subtitle.
OSD Background
Transparency
100%
Set the background transparency of OSD
screen.
OSD Background
Color
1
2
3
Screen Saver
PCM
Set the brightness of front display.
Set the time to work the screen saver on
the screen.
Set whether the sound recorded in 96kHz
will be down sampled in 48kHz.
Set the type of sound signal which outputs
from the digital audio output jack.
ON
OFF
Compressing the range of sound volume.
ON
OFF
Outputting the sound during play in fast
forward.
Parental Lock
ALL
level 8 to 1
Set the parental level of your DVD discs.
(Change password)
Enter the current
four-digit password
Set and change the password.
Others
Dynamic Range
Control
Fast Forward with
Audio
Changing the SETUP menu
Auto
48kHz
96kHz
Dolby Digital
PCM
Stream
Set the language for OSD
(On Screen Display).
Editing
4.Parental setting
Pages 90-91
Digital Out
English
Français
Español
Auto
Bright
Dark
OFF
5 minutes
10minutes
Set the OSD screen color.
1 (Green), 2 (Blue), 3 (Red)
Playing discs
FL Dimmer
35%
25%
Recording
Audio Language
OSD Language
3.Audio setting
Pages 88-89
Set the language for disc menu.
Getting started
2.Display setting
Pages 86-87
Disc Menu Language English
French
Spanish
Contents
Connections
1.Language setting
Pages 84-85
Items (highlight is the default)
Note
Español
• If you change the setting in SETUP
menu, the information of contents
stays on even when the power is
switched off.
83
Changing the SETUP menu
Settings for Language
Press STOP button if you are playing a disc.
POWER
1
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
REC
DEF
3
PAUSE
4
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
Setup Menu
1
5
2
Select “SETUP” using { / B buttons, then press
ENTER button.
SETUP menu will appear.
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
Setup
Playback Setting
3
Select “Playback” using K / L / { / B buttons, then press
ENTER button.
Option window will appear.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
4:3 Letter Box
All
English
Original
OFF
Digital Out
Dynamic Range Control
ON
Fast Forward with Audio
OFF
4
Select a desired item using K / L buttons, then press
ENTER button.
Note
• Only the languages supported
by the disc can be selected.
• Audio Language setting may
not be available to some
discs.
• You can change or switch off
the subtitles on a DVD disc
also from the disc menu if it
is available.
84
Changing the SETUP menu
Before you start
Settings for Language (cont’d)
Disc Menu Language (Default : English)
Set the language for Disc Menu.
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Setup > Playback
4:3 Letter Box
All
English
TV Aspect
Original
OFF
Audio Language
Parental Lock
Disc Menu Language
Subtitle Language
Digital Out
4:3 Letter Box
All
English
English
French
Original
Spanish
OFF
Other
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Digital Out
Dynamic Range Control
ON
Dynamic Range Control
ON
Fast Forward with Audio
OFF
Fast Forward with Audio
OFF
Setup > Playback
Setup > Playback
TV Aspect
TV Aspect
Original
OFF
Audio Language
Digital Out
Dynamic Range Control
ON
Dynamic Range Control
ON
Fast Forward with Audio
OFF
Fast Forward with Audio
OFF
Disc Menu Language
Audio Language
Subtitle Language
Parental Lock
Disc Menu Language
Subtitle Language
Digital Out
Recording
4:3 Letter Box
All
English
4:3 Letter Box
All
Original
English
English
Original
French
OFF
Spanish
Other
Parental Lock
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Setup > Playback
TV Aspect
Disc Menu Language
4:3 Letter Box
All
English
Audio Language
Original
Audio Language
Subtitle Language
OFF
Subtitle Language
TV Aspect
Parental Lock
Parental Lock
Disc Menu Language
Digital Out
4:3 Letter Box
All
OFF
English
English
Original
French
Digital Out
OFF
Spanish
Other
ON
Dynamic Range Control
ON
Fast Forward with Audio
OFF
Fast Forward with Audio
OFF
Editing
Dynamic Range Control
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
age
e
Code Input
Audio
---ON
• When you finish entering
the code, press ENTER
button. Refer to the language code table on page
95.
Others
Control
Changing the SETUP menu
If “Other” is selected, press 4-digit code number using number buttons.
All
English
English
French
Original
Spanish
OFF
Other
Playing discs
Subtitle Language (Default : OFF)
Set the subtitle language.
Setup > Playback
Getting started
Audio Language (Default : Original)
Set the Audio language.
Connections
Setup > Playback
OFF
5
Español
Press SETUP button to exit SETUP menu.
85
Changing the SETUP menu
Settings for Display
Press STOP button if you are playing a disc.
POWER
1
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
REC
DEF
3
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
Setup Menu
1
5
2
Select “SETUP” using { / B buttons, then press
ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Display” using K / L / { / B buttons, then press
ENTER button.
Option window will appear.
Setup > Display
OSD Background Transparency 35%
OSD Background Color
OSD Language
1
English
FL Dimmer
Bright
Screen Saver
10 minutes
4
Select a desired item using K / L buttons, then press
ENTER button.
86
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
Changing the SETUP menu
Setup > Display
Setup > Display
OSD Background Transparency 35%
OSD Language
1
English
FL Dimmer
Bright
Screen Saver
10 minutes
OSD Background Transparency 35%100%
85%
OSD Background Color
1
70%
OSD Language
English
50%
FL Dimmer
Bright
35%
25%
Screen Saver
10 minutes
10%
0%
Setup > Display
Setup > Display
OSD Background Transparency 35%
OSD Background Transparency 35%
OSD Background Color
OSD Background Color
OSD Language
1
English
FL Dimmer
Bright
FL Dimmer
11
2
English
3
Bright
Screen Saver
10 minutes
Screen Saver
10 minutes
OSD Language
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Recording
OSD Language (Default : English)
Set the language for OSD.
Setup > Display
Setup > Display
OSD Background Transparency 35%
OSD Background Color
1
OSD Background Color
OSD Language
English
OSD Language
FL Dimmer
Bright
FL Dimmer
Screen Saver
1
English
English
Français
Bright
Español
10 minutes
Screen Saver
10 minutes
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Setup > Display
OSD Background Transparency 35%
OSD Background Color
OSD Background Color
OSD Language
1
English
FL Dimmer
Bright
FL Dimmer
Screen Saver
10 minutes
Screen Saver
OSD Language
1
English
Bright
Auto
10
minutes
Bright
Dark
Screen Saver (Default : 10 minutes)
Set the time to work the screen saver function on the screen.
Setup > Display
OSD Background Transparency 35%
OSD Background Transparency 35%
OSD Background Color
OSD Background Color
OSD Language
1
English
FL Dimmer
Bright
FL Dimmer
Screen Saver
10 minutes
Screen Saver
OSD Language
1
English
OFF
5Bright
minutes
1010
minutes
minutes
15 minutes
30 minutes
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Español
5
Press SETUP button to exit SETUP menu.
Others
Setup > Display
Changing the SETUP menu
OSD Background Transparency 35%
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Editing
FL Dimmer (Default : Bright)
Set the brightness of front display.
You can choose one among “Auto”, ”Bright” and ”Dark”.
When “Auto” is selected, the display dims after 15 seconds of no use.
Playing discs
OSD Background Transparency 35%
Setup > Display
Getting started
OSD Background Color (Default : 1 Green)
Set the OSD screen color.
You can choose one among 1(Green), 2(Blue), and 3(Red).
Connections
OSD Background Color
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Before you start
Settings for Display (cont’d)
OSD Background Transparency (Default : 35%)
Set the background transparency of OSD screen.
You can choose one among 0% through 100%.
87
Changing the SETUP menu
Settings for Audio
Choose the appropriate Audio settings for your equipment as
it only affect during the playback of DVD discs.
Press STOP button if you are playing a disc.
POWER
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
1
CH
REC
MONITOR
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
REC
DEF
3
PAUSE
SKIP
F
H
G
B
PLAY
REV
FWD
h
g
STOP
C
1
5
Setup Menu
2
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
Select “SETUP” using { / B buttons, then press
ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Playback” using K / L / { / B buttons, then press
ENTER button.
Option window will appear.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
4:3 Letter Box
All
English
Original
OFF
Digital Out
Dynamic Range Control
ON
Fast Forward with Audio
OFF
4
Select a desired item using K / L buttons, then press
ENTER button.
Note
• Dynamic Range Control function is available only on the
discs which are recorded in
the Dolby Digital format.
88
Changing the SETUP menu
Setup > Playback
TV Aspect
Setup > Playback
Disc Menu Language
4:3 Letter Box
All
English
Audio Language
Original
Audio Language
Original
Subtitle Language
OFF
Subtitle Language
Parental Lock
Parental Lock
Digital Out
Digital Out
Dynamic Range Control
ON
Dynamic Range Control
Fast Forward with Audio
OFF
Fast Forward with Audio
Settings for Dolby Digital (Default : Stream)
Original
OFF
ntrol
udio
PCM
ON
Dolby
Digital
PCM
Stream
OFF
• Select a setting using K / L buttons, then press ENTER button.
Your setting will be activated.
PCM : Convert the Dolby Digital into PCM(2 channel).
When your amplifier/decoder is NOT compatible with Dolby Digital, set
to “PCM”.
Stream : Outputs a Dolby Digital signals
When your amplifier/decoder is compatible with Dolby Digital, set to
“Stream” .
Settings for PCM (Default : Auto)
Original
OFF
udio
PCM Auto
48kHz
ON
Dolby
Digital
96kHz
OFF
Setup > Playback
TV Aspect
Disc Menu Language
Audio Language
Subtitle Language
Setup > Playback
4:3 Letter Box
All
English
TV Aspect
Original
OFF
Audio Language
Digital Out
Parental Lock
Disc Menu Language
Subtitle Language
4:3 Letter Box
All
English
Original
OFF
Digital Out
Dynamic Range Control
ON
Dynamic Range Control
ON
Fast Forward with Audio
OFF
Fast Forward with Audio
OFF
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
ON
OFF
Fast Forward with Audio (Default : OFF)
Set to ON to output the sound during play in fast forward of x2.
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Setup > Playback
4:3 Letter Box
All
English
TV Aspect
Original
OFF
Audio Language
Digital Out
Parental Lock
Disc Menu Language
Subtitle Language
4:3 Letter Box
All
English
Original
OFF
• Select a setting using K / L
buttons, then press ENTER
button.
Your setting will be activated.
Others
Setup > Playback
Changing the SETUP menu
Parental Lock
Editing
Dynamic Range Control (Default : ON)
Set to ON to compress the range between soft and loud sounds.
Note
When playing disc with
copyright protection
• If you select “Auto”, the
sound will be down sampled at 48kHz.
• If you select “96kHz”, no
digital sound will be output. Select “Auto”, so
that outputting 48kHz
digital sound.
Playing discs
ntrol
• Select a setting using K / L buttons, then
press ENTER button.
Your setting will be activated.
Auto
: Select “Auto” usually.
48kHz : If your amplifier/decoder is NOT compatible with 96kHz PCM, select “48kHz”.
96kHz sound will be output in 48kHz.
96kHz : If your amplifier/decoder is compatible
with 96kHz PCM, select “96kHz”. 96kHz
sound will be output.
Recording
B
OFF
PCM
ON
Dolby
Digital
OFF
Getting started
A
Connections
TV Aspect
Disc Menu Language
4:3 Letter Box
All
English
• Select a setting using K / L
buttons, then press ENTER
button.
Option window will appear.
Proceed to steps A or B.
Before you start
Settings for Audio (cont’d)
Digital Out
Set the digital audio output.
Digital Out
Dynamic Range Control
ON
Dynamic Range Control
Fast Forward with Audio
OFF
Fast Forward with Audio
ON
ON
OFF OFF
Español
5
Press SETUP button to exit SETUP menu.
89
Changing the SETUP menu
Settings for Parental lock level
Some DVD-Video discs feature a Parental Lock level. Playback
will stop if the ratings exceed the levels you set, it will require
you to enter a password before the disc will playback.This feature prevents your children from viewing inappropriate materials.
POWER
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
OPEN/CLOSE
A
Press STOP button if you are playing a disc.
CH
REC
MONITOR
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
SPACE
0
CM SKIP
REC SPEED CLEAR
1
REC
PAUSE
4
SKIP
F
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
DEF
3
H
G
B
PLAY
REV
FWD
h
g
STOP
C
1
5
Setup Menu
SETUP
TOP MENU
MENU/LIST
K
ENTER
REPEAT
{
B
RETURN
ZOOM
L
2
3
4
2
Select “SETUP” using { / B buttons, then press
ENTER button.
SETUP menu will appear.
Setup
Playback Setting
3
Select “Playback” using K / L / { / B buttons, then press
ENTER button.
Option window will appear.
Setup > Playback
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
4:3 Letter Box
All
English
Original
OFF
Digital Out
Dynamic Range Control
ON
Fast Forward with Audio
OFF
4
Select “Parental Lock” using K / L buttons, then press
ENTER button.
90
Note
• Parental lock function may
not be available to some
discs.
• With some DVDs, it may be
difficult to find if they are
compatible with parental lock.
Be sure to check if the
parental lock function operates in the way that you have
set.
• Record the password in case
you forget it.
Changing the SETUP menu
Before you start
Settings for Parental lock level (cont’d)
Parental Lock (Default : All)
Set the Parental Lock level.
Setup > Playback
TV Aspect
Disc Menu Language
Audio Language
Subtitle Language
4:3 Letter Box
All
English
TV Aspect
Original
OFF
Audio Language
Parental Lock
Disc Menu Language
Subtitle Language
Digital Out
Digital Out
Dynamic Range Control
ON
Dynamic Range Control
Fast Forward with Audio
OFF
Fast Forward with Audio
Getting started
A
4:3
All Letter Box
8
All
7
English
6
Original
5
OFF
4
3
2
ON
1
OFF
• Change the parental level
using K / L buttons, then
press ENTER button.
Option window will appear
Proceed to steps A or B.
Connections
Parental Lock
Setup > Playback
A password has not been set yet
Setup > Playback
Setup > Playback
TV Aspect
Yes
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
4:3
Password
All Letter Box
8- - - All
7
English
6
Original
5
OFF
4
3
2
ON
1
OFF
Recording
4:3
Letter Box
Change
AllPassword?
Yes
No
8
All
7
English
Disc Menu Language
6
Original
Audio Language
5
OFF
Subtitle Language
4
3
Digital Out
2
ON
Dynamic Range Control
1
Fast Forward with Audio
OFF
Parental Lock
• Select “Yes” using s / B
buttons, then enter a new
password using Number
buttons.
Your setting will be activated.
B
A password has been set already
Setup > Playback
TV Aspect
Parental Lock
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
4:3
Letter Box
Change
AllPassword?
Yes
No
8
Parental Lock
All
7
English
Disc Menu Language
6
Original
Audio Language
5
OFF
Subtitle Language
4
3
Digital Out
2
ON
Dynamic Range Control
1
Fast Forward with Audio
OFF
• If you select “No”, proceed
to Step 5.
Setup > Playback
Yes
TV Aspect
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
4:3
Password
All Letter Box
8- - - All
7
English
6
Original
5
OFF
4
3
2
ON
1
OFF
Changing the SETUP menu
• Enter the current password
using Number buttons.
TV Aspect
Editing
Disc Menu Language
Change the password
Setup > Playback
4:3
All Letter Box
Password
8
All
7* * * *
English
6
Original
5
OFF
4
3
2
ON
1
OFF
Playing discs
• If you select “No”, proceed
to Step 5.
• Select “Yes” using s / B
buttons, then enter a new
password using Number
buttons.
Your setting will be activated.
Note
Press SETUP button to exit SETUP menu.
Español
91
Others
5
• Press CLEAR button to erase
numbers entered incorrectly.
• When you forget the password or you want to clear all
settings in Parental lock, enter
4,7,3,7 using Number buttons
in option window. Password
will be cleared and parental
levels will be set to All.
Others
Troubleshooting
Before requesting service for this DVD recorder, check the table below for a possible cause of the problem
you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem
and restore proper operation.
Symptom
Remedy
Power
The power does not turn on.
• Check that the AC power cord is connected securely.
There is no picture.
• Re-connect the connecting cord securely.
• The connecting cords are damaged.
• The Setup Display appears. Press RETURN
button to turn
off the display.
• Check the connection to your TV (page 13).
• Switch the input selector on your TV (such as to "LINE1") so
that the signal from the DVD recorder appears on the TV
screen.
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output signal from the DVD recorder passes
through your VCR to get to your TV, or if you are connected to
a combination TV/VIDEO player, the copy-protection signal
applied to some DVD programs could affect picture quality. If
you still experience this problem even when you connect the
DVD recorder directly to your TV, try connecting the DVD
recorder to your TV's S-VIDEO input.
TV program reception does not fill the
screen.
• Try to set the channels with "Auto Preset" in SETUP menu
(page 18).
• Select a channel of any TV program using the CH o / p
buttons.
• Reorient the TV antenna.
• Adjust the picture (see the TV's instruction manual).
• Place the DVD recorder and TV farther apart.
• Place the TV and any bunched antenna cables farther apart.
• Switch the input to TV.
• Connect the antenna cable correctly (page 13).
Picture
TV program pictures are distorted.
TV channels cannot be changed.
The playback picture or TV program from
the equipment connected through the
DVD recorder is distorted.
• If the playback picture output from a DVD player,VCR, or tuner
goes through the DVD recorder before reaching your TV, the
copy-protection signal applied to some programs could affect
picture quality. Disconnect the playback equipment in question
and connect it directly to your TV.
There is no sound.
• The disc is dirty or flawed.
• Re-connect all connections securely.
• The connecting cord is damaged.
• Check the connections to the amplifier input.
• The input source setting on the amplifier is incorrect.
• The recorder is in pause mode or in Slow-motion Play mode.
• The recorder is in fast forward or fast reverse mode.
• If the audio signal does not come through the DIGITAL OUT
(COAXIAL) jack, check the Audio Setup settings (pages 88-89).
Sound is noisy.
• The disc is dirty or flawed.
• When playing a DTS-CD, noise may come from the speakers.
This DVD recorder is not compatible with DTS-CD.
No DTS sound is output
• This DVD recorder is not compatible with DTS sound.
Sound
92
Others
Symptom
Playback
The disc does not play.
• Multilingual subtitle are not recorded on the DVD VIDEO.
• The DVD VIDEO prohibits changing of the subtitles.
• Try changing the subtitle using the DVD VIDEO's menu.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD VIDEO being played.
• You are trying to change the angles when
icon does not
appear on the TV screen (page 56).
• The DVD VIDEO prohibits changing angles.
• Try changing the angle using the DVD VIDEO's menu.
Nothing was recorded even though you
set the timer setting correctly.
•There was a power failure during recording.
• The DVD recorder's internal clock stopped due to a power
failure that lasted for more than 30 seconds.
Reset the clock (pages 22-23).
• Disconnect the AC power cord from the AC outlet, and
connect it again.
• The program contains copy protection signals that restricts
copying.
• The timer setting overlapped with another setting that was set
later or has priority.
• It will take a few seconds for the DVD recorder to input disc
data before recording can stop.
• The timer setting overlapped with another setting that was set
later or has priority (page 36).
• Disc space was not enough.
93
Español
Timer recording is not complete or did
not start from the beginning.
• An unused DVD-R or DVD-RW was inserted. It takes a while
for the DVD recorder to automatically format a DVD-RW.
Others
Recording does not stop immediately
after you press STOP C button.
• Set the TV's input to "TV."
Changing the SETUP menu
Recording/Timer recording/Editing
The channel cannot be changed from the
channel you are recording.
Recording does not start immediately
after you press REC button.
Editing
The subtitle language cannot be changed
or turned off.
Playing discs
The language for the sound track cannot
be changed.
• Depending on the disc, you may not be able to do some of the
operations above. See the instruction manual supplied with the
disc.
• Multilingual tracks are not recorded on the DVD VIDEO,
DVD-R or DVD-RW being played.
• The DVD VIDEO prohibits the changing of the language for the
sound track.
• Try changing the language using the DVD VIDEO's menu.
Recording
Some functions such as Stop, Search, or
Slow-motion Play cannot be performed.
Getting started
The DVD recorder starts playing from the
disc automatically.
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side
facing up.
• The disc is not correctly inserted.
• The DVD recorder cannot play certain discs (such as a CDROM) (page 41).
• The region code on the DVD VIDEO does not match the DVD
recorder (page 41).
• Moisture has condensed inside the DVD recorder. Remove the
disc and leave the DVD recorder turned on for about half an
hour until the moisture evaporates (page 4).
• If the disc was recorded on another recorder, the DVD
recorder cannot play the disc if it was not finalized (page 39).
• Resume play was activated (page 46). Press STOP C button
twice.
• You have inserted a disc whose Title menu or DVD menu
automatically appears on the TV screen when it is first insert.
• The DVD VIDEO features an auto playback function.
Connections
The disc does not start playback from the
beginning.
Remedy
Before you start
Troubleshooting (cont’d)
Others
Troubleshooting (cont’d)
Symptom
Remedy
Remote control
The remote does not function.
• Batteries are weak.
• There are obstacles between the remote and the DVD
recorder.
• The remote is far from the DVD recorder.
• There are no batteries in the remote.
• Turn on the DVD recorder.
• The remote is not pointed at the remote sensor on the DVD
recorder.
Others
The DVD recorder does not operate
properly.
• When static electricity, etc., causes the DVD recorder to
operate abnormally, unplug the DVD recorder and then plug it
in again.
The disc tray does not open when you
press OPEN/CLOSE A button.
• It may take a few seconds for the disc tray to open after you
have recorded or edited a disc.
• This is because the DVD recorder is adding disc data to the
disc.
Error message
Disc Error
--- Please eject the disc. --Playback feature may not be
available on this Disc.
Solution
Unplayable disc is inserted
in the DVD recorder.
Insert the standardized disc which
bear the marks on page 41.
Region Error
--- Please eject the disc. --Playback is not authorized in your
region.
Playback is not authorized
in the region of the DVD-Video
disc which you inserted in the
DVD recorder.
Insert the DVD-Video disc with
region codes 1 or ALL.
Parental Lock On
--- Please eject the disc. --The current selected parental level
Prohibits playback.
The current selected parental
level in the SETUP Menu
prohibits playback.
Check the "Parental Lock" setting
(pages 90-91).
The recording function encountered
the copy prohibited program.
You cannot record copy prohibited
programs.
Recording Error
This program is not
recordable in Video mode.
You are trying to record the copyonce program onto the DVD-RW
disc in Video mode.
Set "DVD-RW Recording Format"
to "VR mode" (page 28).
Recording Error
You are trying to record onto the
disc which is unrecordable, or the
disc status is unable to record.
Insert the recordable disc, and
ensure the disc status is satisfied
with recording (pages 26-40).
You are trying to record the copyonce program onto the DVD-RW
disc which is not compatible with
CPRM.
Insert the DVD-RW disc
(ver.1.1 compatible with CPRM).
You are trying to record on to the
protected disc which is set in the
Disc Setting Menu.
Release the disc protect setting
in the Disc Setting menu (page 40).
Recording Error
This program is not allowed
to be recorded.
Can not record on this disc.
Recording Error
This program is not allowed to
be recorded on this disc.
Recording Error
This disc is protected and not
recordable.
94
Cause
Others
Changing the SETUP menu
Others
Code
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Editing
Language
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Playing discs
Code
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6247
6265
5247
6258
6266
6367
6459
6461
Recording
Language
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Occitan
Oriya
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Romanian
Getting started
Code
6159
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
Connections
Language
(Afan) Oromo
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Before you start
Language code
Español
95
Others
Glossary
Analog audio
An electrical signal that directly
represents sound. Compare this
to digital audio which can be an
electrical signal, but is an indirect
representation of sound. See also
Digital audio.
Aspect ratio
The width of a TV screen relative
to its height. Conventional TVs are
4:3 (in other words, the screen is
almost square); widescreen models
are 16:9 (the screen is almost
twice as wide as it is high).
Chapter
Just as a book is split up into several chapters, a title on a DVD
disc is usually divided into chapters. See also Title.
Component video output
Each signal of luminance(Y) and
component(PB/CB, PR/CR) is independent to output so that you can
experience picture color as it is.
CPRM
(Content Protection for
Recordable Media)
CPRM is a copy protection system with scramble system regarding the recording of “copy-once”
broadcast programs (e.g. some
satellite broadcasts).
Digital audio
An indirect representation of
sound by numbers. During recording, the sound is measured at discrete intervals (44, 100 times a
second for CD audio) by an analog-to-digital converter, generating
a stream of numbers. On playback,
a digital-to-analog converter generates an analog signal based on
these numbers. See also Sampling
frequency and Analog audio.
96
Dolby Digital
The system to compress digital
sound developed by Dolby
Laboratories. It offers you sound
of stereo(2ch) or multi-channel
audio (up to 5.1ch).
MP3 (MPEG Audio Layer 3)
MP3 is a method of compressing
files.You can copy MP3 files on
CD-R/RW discs from the computer and play the files on this unit.
Finalize
To make DVD discs, which have
done recording, possible to play in
DVD players.With this DVD
recorder, it is possible to finalize
DVD-R/DVD-RW discs.
PCM
(Pulse Code Modulation)
The most common system of
encoding digital audio, found on
CDs and DAT. Excellent quality,
but requires a lot of data compared to formats such as Dolby
Digital and MPEG audio. For compatibility with digital audio
recorders (CD, MD and DAT) and
AV amplifiers with digital inputs,
this unit can convert Dolby Digital
and MPEG audio to PCM. See also
Digital audio.
Playlist
From this list you can play contents of a disc as your desired
order or in sequence. Also it is
allowed to search a specific scene
directly.
Regions code
Regions associate discs and players with particular areas of the
world.This unit will only play discs
that have compatible region
codes.You can find the region
code of your unit by looking on
the rear panel. Some discs are
compatible with more than one
region (or all regions).
Sampling frequency
The rate which sound is measured
by a specified interval to turn into
digital audio data.The numbers of
sampling in one second defines as
sampling frequency.The higher the
rate, the better the sound quality
as possible as it is.
SAP
(Secondary Audio Program)
Sub-audio channel which is delivered separately from main-audio
channel.This audio channel is used
as an alternate in bilingual broadcasting.
S-Video output
It delivers independently each signal of color(C) and luminance(Y)
to TV as video signals, so that
higher-quality picture will be
gained.
Title (DVD only)
A collection of chapters on DVD
disc. See also chapter.
Track
Audio CDs use tracks to divide
up the content of a disc.The DVD
equivalent is called a chapter. See
also Chapter.
Others
Before you start
Specifications
General
DVD-Video, DVD-R/RW, Audio CD
AC120 V, 60 Hz
23 W (standby: 4.0 W)
6.0 lbs ( 2.7 kg )
17 1/8" x 2 5/8" x 11 3/4" (435 x 66 x 297 mm)
41Fº to 104Fº (5ºC to 40ºC)
5% to 85% (no condensation)
NTSC
Connections
System
Power requirements
Power consumption
Weight
Dimensions (width x height x depth)
Operating temperature
Operating humidity
TV format
Recording
DVD VideoRecording, DVD-VIDEO
DVD-ReRecordable, DVD-Recordable
Getting started
Recording format
Recordable discs
Video recording format
Sampling frequency
Compression format
Audio recording format
Sampling frequency
Compression format
13.5MHz
MPEG
48kHz
Dolby Digital
Receivable channels
VHF
UHF
CATV
Recording
Tuner
2-13ch
14-69ch
C1-C125ch
Input/Output
VHF/UHF set 75Ω
Input 1 (rear), 2 (front)
1 Vp-p (75Ω)
RCA jack
Output 1,2
1 Vp-p (75Ω)
RCA jack
Input 1 (rear), 2 (front)
1 Vp-p (75Ω)
286 mVp-p (75Ω)
4 pin mini DIN
Playing discs
Editing
1 Vp-p (75Ω)
286 mVp-p (75Ω)
4 pin mini DIN
Changing the SETUP menu
Y: 1.0 Vp-p (75Ω), CB, CR: 0.7 Vp-p (75Ω)
RCA jacks
Input 1 (rear), 2 (front) L/R
2V rms (Input impedance: more than 22kΩ)
RCA jacks
Output 1,2 L/R
2V rms (Output impedance: less than 1kΩ)
RCA jacks
Others
VHF/UHF antenna input/output terminal
Video input
Input level
Jacks
Video output
Output level
Jacks
S-Video input
Y (Iuminance) - Input level
C (color) - Input level
Jacks
S-Video output
Y (Iuminance) - Output level
C (color) - Output level
Jacks
Component video output
Output level
Jacks
Audio input
During audio input
Jacks
Audio output
During audio output
Jacks
Digital audio output
Output level
Jacks
500 mVp-p (75Ω)
RCA jack
Note:
The specifications and design of this product are subject to change without notice.
Español
97
Español
Fácil grabación de DVD
Estas instrucciones le ayudarán a entender fácilmente cómo grabar discos DVD.
Nota:
Asegúrese que las pilas están en el mando a distancia y que ha conectado correctamente esta unidad y el TV.
Paso 1: Elija un tipo de disco
Paso 2:Coloque un disco en blanco
Mando a distancia
Hay varios tipos de discos DVD que puede grabar
según el uso. Elija el tipo según "Tipos de disco
DVD" en esta página.
Este grabador de DVD puede grabar en los siguientes tipos de disco.
POWER
DISPLAY
TIMER
PROG.
OPEN/CLOSE
1
CH
2
Para abrir
A
.@/:
1
ABC
2
DEF
3
GHI
JKL
MNO
Para
encender
Por ejemplo, cuando desea grabar repetidamente
en el mismo disco o cuando desea editar el disco
después de grabar, seleccione el disco de tipo
regrabable DVD-RW.
POWER
OPEN/CLOSE
DISPLAY
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
JKL
MNO
A
CH
Cuando desea guardar grabaciones sin alterarlos,
un DVD no regrabable DVD-R puede ser más
conveniente.
3
Para cerrar
Cargando
Esta operación puede
demorar en reconocerse.
Tipos de disco DVD
.
: Más adecuado
: Puede utilizar
Formato del disco
: Algunas funciones son limitadas
Desea
DVD-RW VR
: No puede utilizar
DVD-RW Video
DVD-R
DVD-RW Video
DVD-R
No
Grabar programas de TV
Volver a utilizar borrando partes no deseadas
Editar las grabaciones
Editar/grabar de equipos conectados
Copiar discos para distribución
*1
Reproducir en otro equipo de DVD
*1
Detalles
DVD-RW VR
Grabación
¿Regrabable?
Sí
Sí
Puede crear capítulos a intervalos fijos (auto.)
Sí
Sí
Sí
Puede crear capítulos donde desee (manual)
Sí
No
No
Puede grabar imágenes de tamaño 16:9
Sí
Sí
Sí
Puede grabar un programa de Copia-una-vez
Sí
No
No
Edición
*1
98
Puede hacer funciones de edición básica
Sí
Sí
No
Puede hacer funciones de edición avanzadas (edición de lista a reproducir)
Sí
No
No
El DVD-RW (modo VR) sólo puede reproducirse
en equipos de DV compatibles con VR.
Nota:
Para más detalles sobre las funciones anteriores y las
limitaciones implícitas, lea las explicaciones en este manual.
Coloque el disco en el
grabador. Haga el formato del
disco del menú SETUP, existen los formatos de video
(modo de Video) o de
grabación de video (modo
VR) según el tipo de disco
colocado. Esto es necesario
para preparar el disco para
grabación.Vea los detalles en
las páginas 28-30.
Español
Before you start
Fácil grabación de DVD (cont.)
POWER
DISPLAY
TIMER
PROG.
OPEN/CLOSE
Paso 4: Seleccione
el canal
deseado
POWER
DISPLAY
TIMER
PROG.
CH
REC
MONITOR
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
TUV
8
WXYZ
9
SPACE
0
CM SKIP
CH
REC
MONITOR
.@/:
1
ABC
2
DEF
3
TIMER
PROG.
.@/:
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
A
GHI
4
JKL
5
MNO
6
PQRS
7
REC SPEED CLEAR
TUV
8
WXYZ
9
SPACE
0
CM SKIP
CH
REC
MONITOR
REC
TUV
8
WXYZ
9
SPACE
0
CM SKIP
PQRS
7
REC SPEED CLEAR
REC
REC
OPEN/CLOSE
DISPLAY
A
PAUSE
Getting started
PQRS
7
REC SPEED CLEAR
POWER
OPEN/CLOSE
A
.@/:
1
Paso 5: Grabe en
discos
DVD
Connections
Paso 3: Seleccione la
velocidad de
grabación
SKIP
F
H
G
CH 1
SP 2:01 Rem.
Recording
I
Sugerencia 1: Reproduzca el contenido grabado
Paso 6: Pare la
grabación
Playing discs
Puede seleccionar el título que desea reproducir de un menú indicado y empiece
a reproducir inmediatamente. Las grabaciones pueden verse fácilmente en un
disco, el procedimiento es simple ya que
Parada/inicio
Parada grab.
sólo tiene que elegir el título en un capí- Inicio de grab.
tulo de la pantalla del menú.
¿Qué son títulos y capítulos?
Título 1
Título 2
7
REC SPEED CLEAR
REC
8
9
SPACE
0
CM SKIP
PAUSE
Editing
La grabaciones del disco DVD se dividen generalmente en títulos. Los títulos
pueden subdividirse en capítulos.
SKIP
F
H
Capítulo 1 Capítulo 2 Capítulo 3 Capítulo 1 Capítulo 2
G
B
PLAY
REV
FWD
h
g
STOP
C
SETUP
TOP MENU
MENU/LIST
K
Changing the SETUP menu
Sugerencia 2: Edite el disco grabado
La edición de discos puede ser muy fácil y el grabador de DVD ofrece convenientes funciones de edición posibles sólo con los discos DVD-R/RW.
Puede editar lo siguiente de la lista de títulos.
• Poniendo nombres en títulos
• Seleccionando imágenes para índices (modo VR)
• Seleccionando/borrando marcadores de capítulos
• Borrando partes de títulos (modo VR)
58%
Escrit de datos
Others
Original y Playlist (modo VR)
Puede editar las grabaciones en la lista a reproducir sin cambiar las grabaciones
originales. Cualquier lista a reproducir no ocupa mucho espacio en el disco.
¿Qué significa "Original" o "Playlist"?
Español
A lo largo de este manual encontrará Original y Playlist que se refieren a las
grabaciones reales y la versión editada.
• La grabación Original se refiere a la grabación real en el disco.
• El Playlist se refiere a la versión editada del disco; cómo se va a reproducir
la versión Original.
Esta operación puede
demorar en completarse.
99
LIMITED WARRANTY
FUNAI CORP. will repair this Emerson product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
LABOR:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are
excluded from this warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from
the date of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER
WITH THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,
missing or if service was attempted by an unauthorized service center. This Emerson Limited warranty
does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal
use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse,
mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as
hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts
of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT
REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR
MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY
THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART
OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT
FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT
PRIOR NOTICE.
To locate your nearest Emerson Authorized Service Center or for general service procedure,
please call 1-800-605-8457 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-605-8457
http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN04178 / E6520UD ★★★★