(1) SWITCH HOUSING
ASSEMBLY
WHITE WIRE
(3) WIRE
CONNECTORS
WHITE WIRE
FAN SWITCH
CHAIN
BLUE WIRE
BLACK WIRE
(4) CENTER
SCREW
(2) SCREWS
(7) HEX NUT
4. Installation is complete. Turn electricity
on at the main fuse or circuit breaker
box.
NOTE: It is advisable to periodically
check the tightness of the shade
retainers. Fan operation may cause
them to loosen.
(8) LOCKWASHER
(6) LIGHT FITTER
SWITCH
HOUSING
READ AND SAVE THESE INSTRUCTIONS
THIS OWNER’S MANUAL
COVERS EMERSON LIGHT KITS
FAN SWITCH
CHAIN
FITTER
USE THESE FIXTURES ONLY WITH EMERSON
CF AND F SERIES CEILING FANS.
Figure 4
9. Proceed to “Installation of “Glass
Shades” section.
Installation of Glass Shades
1. Remove shade retainer from socket.
Seat shade in shade holder and screw
shade retainer onto socket. Repeat for
other two shades.
2. Install a 60-watt (maximum) intermediate
base light bulb into each socket.
!
CHAIN PULL
LIGHT SWITCH
CHAIN
60-WATT (MAX.)
INTERMEDIATE
BASE BULB (3)
NOTE: ANY LIGHT KIT OR FITTER AND GLASS COMBINATION
COVERED BY THIS MANUAL WEIGHS 5.8 LBS. OR LESS.
SHADE HOLDER
Ceiling Fan Light Fixture
Owner's Manual
THREADED
SOCKET
WARNING
LIMITED WARRANTY
To avoid fire hazard, do not exceed
wattage indicated on the fixture.
GLASS SHADE
Figure 5
SHADE RETAINER
3. Install chain pull onto the light switch
chain.
For repair parts, phone:
1-800-654-3545
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant ¥ St. Louis, MO 63136
Part No. BP7254-2
Form No. F40BP72540002
Printed in China 09/06
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original purchaser or user of the
product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT
NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF
OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson
Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Light Fixture should
be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no employee,
agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR
DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss
of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product
does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Form No. F40BP72540002
Part No. BP7254-2
U.L. Model No.: LK37, LK800, LK801, LK803, F468
!
WARNING
Safety Instructions
To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's
Manual for future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Before installing or servicing the light fixture or ceiling fan, switch power off at
service panel and lock service panel disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a warning device, such as a tag, to the service panel.
3. Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or
circuit breaker box before wiring.
2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to national and local electrical codes.
4. Follow the recommended instructions for the proper method of wiring your new light
fixture. If you feel you do not have enough electrical wiring knowledge or experience,
have your light fixture installed by a licensed electrician. Any electrical work not
described in this manual should be performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on
Emerson “CF” and “F” Series Ceiling Fans. This light kit is not to be used with CF652,
CF653, CF670, CF680, CF742 and CF2000 Series Ceiling Fans installed in damp or wet
locations.
7. Insert the black and white wires through
the lockwasher (8) and hex nut (9)
(supplied). Firmly tighten the hex nut to
secure the light fitter to the switch cup.
8. Connect the white wire from the switch
cup to the white wire of the light fitter
(Figure 2). Connect the blue wire from
the switch cup to the black wire of the
light fitter. Use listed wire connectors
(previously removed in step 5) to make
connections (Figures 2 and 3).
(4) MOTOR
CONNECTOR
11. Position the cup/light fitter (1)(7) on the
cover plate (2) and install the three
screws (3) that were previously
removed in step 2 and tighten
securely.
12. Proceed to “Installation of “Glass
Shades” section.
Installation on Emerson Fans
Having Two-Piece Die-Cast
Switch Housings
1.Remove all parts and parts packages
from carton.
2.Remove the cover (5) from the switch
housing (1) by removing the two outer
screws (2). (See Figure 4.)
3.Remove the center screw (4) from the
cover (5). Insert the black and white
wires from the light kit fitter (6) through
the hole and thread the switch housing
cover tightly onto the light kit fitter.
4.Insert the black and white wires through
the lockwasher (8) and hex nut (7)
supplied. Firmly tighten the hex nut to
secure the light kit fitter to the switch
housing cover (5).
5.Carefully locate the white and blue
wires (labeled either “L” or “LIGHT”) in
the switch housing and remove the
wire connectors (3) from the wires.
6. Connect the white wire from the ceiling
fan to the white wire of the light fitter
(6). Connect the blue wire from the
ceiling fan to the black wire of the light
fitter. Use listed wire connectors
(previously removed in step 3) to make
connections. (Figures 3 and 4.)
7. Carefully tuck all wires and splices into
the switch housing (1).
8. Attach the cover/light fitter (5) (6) to the
switch assembly housing (1) using the
two screws (2) that were removed in
Step 2) (Figure 4.)
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
(6) WIRE
CONNECTORS
BLUE WIRE
BLACK WIRE
(3) SCREWS
WHITE WIRES
FAN SWITCH
CHAIN
(9) HEX NUT
(1) SWITCH CUP
(8) LOCKWASHER
(7) LIGHT FITTER
Assembly and Installation
!
4. Remove the center screw (6) from the
switch cup (Figure 1).
5. Carefully locate the white and blue
wires (labeled either "L" or "LIGHT") in
the switch cup and remove the wire
connectors from the wires.
6. Insert the black and white wires from
the light fitter (7) through the center
hole in the switch cup (Figure 2) and
thread the switch cup onto the light
fitter. Hold wires taut while installing
switch cup to prevent the wires from
twisting.
WARNING
Do not install or use the light fixture
if any part is missing or damaged.
Call toll-free:
1-800-654-3545
!
WARNING
To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.
Installation on Emerson Fans
Having Modular Switch Cup with
Center Screw
1. Remove all parts and parts packages
from the carton.
2. Remove the switch cup (1) from the
cover plate (2) by removing the three
screws (3) around the side of the switch
cup (Figure 1).
3. Disconnect the motor connector (4)
from the switch cup connector (5)
(Figure 1).
Figure 2
NOTE: YOUR FITTER MAY NOT LOOK THE SAME AS
THE ONE IN THIS ILLUSTRATION.
HOWEVER, IT INSTALLS IN A SIMILAR MANNER.
!
WARNING
To avoid possible fire or electrical
shock, make certain no bare wire
strands are exposed outside wire
connectors.
Figure 3
(4) MOTOR
CONNECTOR
(3) SCREWS
(1) SWITCH
CUP
(6) CENTER SCREW
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
9. Carefully tuck all wires and splices
into the switch cup (1). (Figure 2.)
10. Connect the motor connector (4) to
the switch cup connector (5).
!
FAN SWITCH
CHAIN
To avoid possible fire or electric shock,
be careful not to pinch wires between
switch housing and light fitter.
Figure 1
2
WARNING
3