8. Attach the cover/light fitter(5)(6) to the switch
assembly housing(1) using the two
screws(2) that were removed in Step 2)
(Figure 4.)
!
WARNING
To avoid fire or electrical shock, be
careful not to pinch wires between the
switch housing assembly and the cover.
9. Proceed to “Installation of Glass Bowl”
section.
Installation of Glass Bowl
4. Install the light switch chain through the
center of the finial nut(3). Screw the finial nut
finger tight onto the fitters threaded nipple.
CAUTION
Be sure that the fan switch chain does not
make contact with the light bulbs. If
necessary reposition the light fitter to avoid
the fan switch chain from touching the light
bulbs.
5. Install pendants(2) onto light fixture chain
and fan switch chain.
NOTE: It is advisable to periodically check
the tightness of the finial.
6. Installation is complete. Turn on electricity at
main fuse or circuit breaker box.
1. Install two 50-watt (maximum) minicandelabra base halogen bulbs (included)
into the fitter sockets.
!
WARNING
FAN SWITCH
CHAIN
FITTER
SOCKET (2)
To avoid fire hazard, do not exceed
wattage indicated on the fixture.
!
READ AND SAVE THESE INSTRUCTIONS
50-WATT
MINI-CANDELABRA
BASE HALOGEN
BULBS (2)
BOWL CAP
For repair parts, phone:
Suitable for Damp
Locations
Includes 3 finials and 3 outer bowl caps in the following finishes:
Oil Rubbed Bronze, Brushed Steel & Appliance White
Includes: Two 50-Watt Mini-Candelabra Base Halogen Bulbs
Net Weight:
THREADED
NIPPLE
1.8
Lbs.
UL
®
Ceiling Fan Light Fixture Owner's Manual
(1) GLASS
BOWL
OUTER BOWL CAP
(3) FINIAL
2. Place the glass bowl(1) onto the light fitter
by inserting the threaded nipple through the
bottom hole of the bowl.
3. Where applicable, insert the fan speed
control switch chain through the offset hole
in the bowl cap, glass bowl and then the
offset hole in the outer bowl cap.
LK130
LIGHT FITTER
WARNING
Over lamping the light kit will result in
the lamps being automatically shut off.
Use only 50-watt maximum minicandelabra base halogen lamps. Turn off
electricity before replacing the lamps.
Model Number:
FAN SPEED CONTROL
SWTICH CHAIN
(WHERE APPLICABLE)
LIGHT SWITCH
CHAIN
PENDANTS (2)
Figure 6
1-800-654-3545
Trouble Shooting
TROUBLE
PROBABLE CAUSE
SUGGESTED REMEDY
1. Both Lamps Will
Not Illuminate.
1. Wiring not complete.
1. Check all wiring connections to light kit.
2. Light bulbs do not light.
2. Check and replace light bulbs.
2. The 1.25A fuse may have blown.
3. Replace fuse.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Form No. BP7414
Part No. F40BP74140000
Printed in China 03/10
LIMITED WARRANTY
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original purchaser or
user of the product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED
TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE
PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR
OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of
Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Light
Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no
employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT
RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not
limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing
other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Form No. F40BP74140000
Part No. BP7414
U.L. Model No.: LK130
!
WARNING
Safety Instructions
To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for
future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan. Before
installing or servicing the light fixture or ceiling fan, switch power off at service panel and lock
service panel disconnecting means to prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely fasten a warning device, such as a
tag, to the service panel.
3. Do not exceed the wattage indicated on fixture (Two 50-watt mini-candelabra base halogen bulbs).
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit
breaker box before wiring.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-2008 and
Local Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical shock. Electrical installation should be made
or approved by a licensed electrician.
3. Make certain no bare wires are exposed outside the wire connectors.
4. All wiring must conform to national and local electrical codes.
5. Follow the recommended instructions for the proper method of wiring your new light fixture. If
you feel you do not have enough electrical wiring knowledge or experience, have your light
fixture installed by a licensed electrician. Any electrical work not described in this manual should
be performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson Model
CF130.
7. Insert the black and white wires through the
lockwasher(8) and hex nut(9) supplied.
Firmly tighten the hex nut to secure the light
kit fitter to the switch cup.
Installation on Emerson Fans
Having Two-Piece Die-Cast
Switch Housings
8. Connect the white wire from the switch cup to
the white wire of the light fitter (Figure 2).
Connect the blue wire from the switch cup to
the black wire of the light fitter. Use the wire
connectors provided with the light kit to make
the electrical connections (Figures 2 and 3).
1. Remove all parts and parts packages from
carton.
2. Remove the cover(5) from the fan switch
housing(1) by removing the two outer
screws(2). (See Figure 4).
FAN SWITCH
CHAIN
(2) COVER PLATE
(4) MOTOR
CONNECTOR
WHITE WIRE
BLACK WIRE
BLUE WIRE
(9) HEX NUT
(5) SWITCH CUP
CONNECTOR
(6) WIRE
CONNECTOR
BLUE WIRE
BLACK WIRE
WHITE WIRES
(8) LOCKWASHER
FAN SWITCH
CHAIN
(3) SCREWS
(1) SWITCH
CUP
(5) COVER
!
WARNING
OUTER BOWL
CAP
Figure 4
5. Carefully locate the white and blue wires
(labeled either "L" or "LIGHT") in the switch
cup and remove the wire connectors from
the wires.
1-800-654-3545
!
!
WARNING
6. Insert the black and white wires from the
light fitter(7) through the center hole in the
switch cup (Figure 2) and thread the switch
cup onto the light fitter. Hold wires taut while
installing switch cup to prevent the wires
from twisting.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
Parts Included: 1 Glass Bowl, 1 Light Fitter,
3 Outer Bowl Caps, 3 Finial Nuts, 2 50-Watt
Mini-Candelabra Base Halogen Bulbs, 2 Wire
Connectors, 2 Pendants, 1 Lockwasher, 1 Hex
Nut and 2 Pull Chains.
(4) MOTOR
CONNECTOR
Installation on Emerson Fans
Having a Modular Switch Cup
with Center Screw
(3) SCREWS
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
(6) LIGHT FITTER
(7) BOWL CAP
3. Remove the center screw(4) from the
cover(5). Insert the black and white wires
from the light kit fitter(6) through the hole
and thread the switch housing cover tightly
onto the light kit fitter.
FAN SWITCH CHAIN
(WHERE APPLICABLE)
WARNING
4. Insert the black and white wires through the
lockwasher(8) and hex nut(9) supplied.
Firmly tighten the hex nut to secure the light
kit fitter to the switch housing cover(5).
4. Remove the center screw(6) from the switch
cup (Figure 1).
Do not install or use the light fixture if any
part is missing or damaged. Call toll-free:
WHITE WIRE
(9) HEX NUT
(8) LOCKWASHER
(4) CENTER
SCREW
(7) LIGHT FITTER
BOWL CAP
3. Disconnect the motor connector(4) from the
switch cup connector(5) (Figure 1).
(3) WIRE
CONNECTORS
(2) SCREWS
Figure 2
Assembly and Installation
(1) SWITCH
HOUSING ASSEMBLY
5. Carefully locate the white and blue wires
(labeled either “L” or “LIGHT”) in the switch
housing and remove the wire connectors(3)
from the wires.
To avoid possible fire or electrical shock,
make certain no bare wire strands are
exposed outside wire connectors.
Figure 3
6. Connect the white wire from the ceiling fan
to the white wire of the light kit fitter(6).
Connect the blue wire from the ceiling fan to
the black wire of the light kit fitter. Use the
wire connectors provided with the light kit to
make the electrical connections (Figures 4
and 5.)
9. Carefully tuck all wires and splices into the
switch cup(1). (Figure 2.)
10. Connect the motor connector(4) to the
switch cup connector(5).
11. Position the switch cup(1) and fitter
assembly(7) on the cover plate(2) and
install the three screws(3) that were
previously removed in Step 2 and tighten
securely.
7. Carefully tuck all wires and splices into the
switch housing(1).
8. Attach the cover/light
fitter(5)(6) to the switch
!
WARNING
12. Proceed to “Installation of Glass Bowl”
section.
1. Remove all parts and parts packages from
the carton.
2. Remove the switch cup(1) from the cover
plate(2) by removing the three screws(3)
around the side of the switch cup (Figure 1).
(1) SWITCH
CUP
(6) CENTER SCREW
Figure 1
2
!
WARNING
To avoid possible fire or electrical shock,
make certain no bare wire strands are
exposed outside wire connectors.
To avoid possible fire or electric shock,
be careful not to pinch wires between
switch cup and the cover plate.
Figure 5
3