5. Carefully locate the white and blue
wires (labeled either “L” or “LIGHT”) in
the switch housing and remove the wire
connectors(3) from the wires.
6. Connect the white neutral wire from the
switch cup to the white neutral wire of the
light fixture (Figure 4). Connect the blue
line (hot) wire from the switch cup to the
black line (hot) wire of the light fixture.
Use listed wire connections (previously
removed in step 5) to make connections
(Figures 4 and 5). The neutral and line
(hot) wires must be installed as instructed
to maintain proper polarly at the
lampholders.
!
WARNING
To avoid possible fire or electrical
shock, make certain no bare wire
strands are exposed outside wire
connectors.
Figure 5
7. Carefully tuck all wires and splices into
the switch housing(1).
8. Attach the cover/light fitter(5)(6) to the
switch assembly housing(1) using the
two screws(2) that were removed in
Step 2) (Figure 4.)
9. Proceed to “Installation of Glass Bowl”
section.
!
!
WARNING
Over lamping the light kit will result in
the lamps being automatically shut off.
Use only 60-watt maximum candelabra
lamps. Turn off electricity before
replacing the lamps.
1. Install three 60-watt (maximum) candelabra
base bulbs into the fitter sockets.
2. Depending on the model purchased, insert
the fan speed control switch chain through
the offset hole in the glass bowl or the hole
in the bowl cap.
3. Install the light switch chain through the
center of the finial nut. Screw the finial nut
finger tight onto the fitters threaded nipple.
CAUTION
Be sure that the fan switch chain does not
make contact with the light bulbs. If
necessary reposition the light fitter to avoid
the fan switch chain from touching the light
bulbs.
4. Install pendants onto light fixture chain and
fan switch chain.
NOTE: It is advisable to periodically check
the tightness of the finial.
5. Installation is complete. Turn on electricity at
main fuse or circuit breaker box.
FAN SWITCH
CHAIN
LIGHT FITTER
BOWL CAP
THREADED NIPPLE
NOTE: YOUR GLASS MAY
NOT LOOK THE SAME AS
THE ONE IN THIS
ILLUSTRATION. HOWEVER,
IT INSTALLS IN A SIMILAR
MANNER.
WARNING
To avoid fire or electrical shock, be
careful not to pinch wires between
the switch housing assembly and
the cover.
Installation of Glass Bowl
(1) GLASS
BOWL
OUTER BOWL CAP
(not on all light kits)
(3) FINIAL
LIGHT SWITCH
CHAIN
Figure 6
PENDANTS (2)
For repair parts, phone:
!
WARNING
1-800-654-3545
To avoid fire hazard, do not exceed
wattage indicated on the fixture.
NOTE: Some light kit models provide a hole
in the glass bowl for the fan switch chain.
While other light kit models provide a bowl
cap including a hole for the fan switch
chain and light switch chain.
Air Comfort Products
READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan Light Fixture
SUITABLE FOR WET LOCATIONS
THREE 60-WATT CANDELABRA BULBS
USE THESE FIXTURES ONLY WITH EMERSON
CF SERIES CEILING FANS.
NOTE: ANY LIGHT KIT OR FITTER AND GLASS COMBINATION
COVERED BY THIS MANUAL WEIGHS 5.8 LBS. OR LESS.
Ceiling Fan Light Fixture
Owner's Manual
LIMITED WARRANTY
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original
purchaser or user of the product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO
LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF
THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR
OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division
of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson
Light Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and
no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT
RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are
not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or
replacing other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply
to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP74510000
Printed in China 11/11
Form No. BP7451
Part No. F40BP74510000
Form No. BP7451
ETL Model No.: LK140 & LK141
!
WARNING
Safety Instructions
To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's
Manual for future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Before installing or servicing the light fixture or ceiling fan, switch power off at
service panel and lock service panel disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a warning device, such as a tag, to the service panel.
3. Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or
circuit breaker box before wiring.
2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to national and local electrical codes.
4. Follow the recommended instructions for the proper method of wiring your new light
fixture. If you feel you do not have enough electrical wiring knowledge or experience,
have your light fixture installed by a licensed electrician. Any electrical work not
described in this manual should be performed by a licensed electrician.
5. WLP100 wet location plate must be installed on light kit when used in wet locations.
WARNING: To reduce the risk of possible fire and electrical shock, install only on
Emerson Ceiling Fan models CF552, CF542, CF620, CF680 CF654 in wet locations with
the WLP100 wet location plate. Permissible to use this light kit on models CF788,
CF787, CF130, CF742 , and CF652 installed in indoor or damp locations. Permissible to
use this light kit on all Emerson CF model ceiling fans installed in indoor locations.
Assembly and Installation
!
WARNING
Do not install or use the light fixture
if any part is missing or damaged.
Call toll-free:
1-800-654-3545
!
WARNING
To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.
4. Remove the center screw(6) from the
switch cup (Figure 1).
5. Carefully locate the white and blue
wires (labeled either "L" or "LIGHT") in
the switch cup and remove the wire
connectors from the wires.
6. Insert the black and white wires from
the light fitter(7) through the center hole
in the switch cup (Figure 2) and thread
the switch cup onto the light fitter. Hold
wires taut while installing switch cup to
prevent the wires from twisting.
(4) MOTOR
CONNECTOR
(3) SCREWS
Installation on Emerson Fans
Having a Modular Switch Cup
with Center Screw
through the center hole of the wet
location plate, secure with lockwasher
and nut (Figure 2).
8. Insert the black and white wires through
the lockwasher(8) and hex nut(9)
supplied. Firmly tighten the hex nut to
secure the light kit fitter to the switch
cup.
9. Connect the white neutral wire from the
switch cup to the white neutral wire of
the light fixture (Figure 2). Connect the
blue line (hot) wire from the switch cup
to the black line (hot) wire of the light
fixture. Use listed wire connections
(previously removed in step 5) to make
connections (Figures 2 and 3). The
neutral and line (hot) wires must be
installed as instructed to maintain proper
polarly at the lampholders.
10. Carefully tuck all wires and splices
into the switch cup(1). (Figure 2.)
11. Connect the motor connector(4) to the
switch cup connector(5).
12. Position the switch cup(1) and fitter
assembly(7) on the cover plate(2) and
install the three screws(3) that were
previously removed in Step 2 and
tighten securely.
(4) MOTOR
CONNECTOR
BLACK WIRE
BLUE WIRE
(9) HEX NUT
(3) SCREWS
(8) LOCKWASHER
(1) SWITCH CUP
HEX NUT
(1) SWITCH
CUP
(6) CENTER SCREW
1. Remove all parts and parts packages Figure 1
from the carton.
7. If installing in a wet location: Install
2. Remove the switch cup(1) from the
the light fitter on plate using the
cover plate(2) by removing the three
lockwasher, nut and rubber washer
screws(3) around the side of the switch
supplied with the WLP100, purchased
cup (Figure 1).
seperately, wet location plate. Placethe
rubber washer on the top of the wet
3. Disconnect the motor connector(4) from
the switch cup connector(5) (Figure 1). 2 location plate, then place the light fitter
WARNING
To avoid possible fire or electric shock,
be careful not to pinch wires between
switch cup and the cover plate.
13. Proceed to “Installation of Glass Bowl”
section.
Installation on Emerson Fans
Having Two-Piece Die-Cast
Switch Housings
1. Remove all parts and parts packages
from carton.
!
WARNING
To avoid possible electric shock, be
sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.
2. Remove the cover(5) from the fan
switch housing(1) by removing the two
outer screws(2). (See Figure 4).
(1) SWITCH
HOUSING
ASSEMBLY
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
BLUE WIRE
(6) WIRE
CONNECTORS
BLACK WIRE
WHITE WIRES
(5) COVER
FAN SWITCH
CHAIN
(2) SCREWS
(4) CENTER
SCREW
LOCKWASHER
RUBBER WASHER
FAN SWITCH
CHAIN
(3) WIRE
CONNECTORS
WHITE WIRES
(9) HEX NUT
(8) LOCKWASHER
(6) LIGHT FITTER
WLP100 WET LOCATION
PLATE PURCHASED
SEPERATELY
(7) LIGHT
FITTER
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
!
BOWL CAP
(7) BOWL CAP
NOTE: YOUR FITTER
MAY NOT LOOK THE
SAME AS THE ONE IN
THIS ILLUSTRATION.
HOWEVER, IT
INSTALLS IN A
SIMILAR MANNER.
Figure 4
3. Remove the center screw(4) from the
cover(5). Insert the black and white
wires from the light kit fitter(6) thru the
hole and thread the switch housing
cover tightly onto the light kit fitter.
NOTE: Wet location plate can not be
used with two piece die-cast switch
housing
4. Insert the black and white wires through
the lockwasher(8) and hex nut(9)
supplied. Firmly tighten the hex nut to
secure the light kit fitter to the switch
housing cover(5).
Figure 2
!
WARNING
To avoid possible fire or electrical
shock, make certain no bare wire
strands are exposed outside wire
connectors.
Figure 3
3