READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan
Light Fixture
Owner’s Manual
Net Weight:
2.6
Lbs.
Model Numbers:
LK150
LK151
Includes: Three 60-Watt
Candelabra Bulbs and Fitter
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1.Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for
future reference.
2.Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing
or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3.Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1.To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker
box before wiring.
2.Make certain no bare wires are exposed outside the wire connectors.
3.All wiring must conform to national and local electrical codes.
4.Follow the recommended instructions for the proper method of wiring your new light fixture. If you
feel you do not have enough electrical wiring knowledge or experience, have your light fixture
installed by a licensed electrician. Any electrical work not described in this manual should be
performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson CF772
Series Ceiling Fans in indoor locations.
Part No. F40BP74420001
Revision: 130402
Form No. BP7442-1
ETL Model Nos.: LK150 and LK151
7. Insert the black and white wires through the lockwasher and hex nut (supplied), firmly tighten the
hex nut to secure the light kit fitter to the switch
cup. Connect the white wire from the switch cup
to the white wire of the light fitter (Figure 2).
Connect the blue wire from the switch cup to the
black wire of the light fitter. Use listed wire connectors (previously removed in Step 5) to make
connections (Figures 2 and 3).
8. Carefully tuck all wires and splices into the switch
cup. (Figure 2.)
9. Connect the motor connector to the switch cup
connector.
10. Position the cup/light fitter in the cover plate and
install the three screws that were previously
removed in Step 2 and tighten securely.
Assembly and Installation
!
WARNING
Do not install or use the light fixture if any part
is missing or damaged. Contact your dealer for
replacement.
!
WARNING
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring.
11. Install three 60-watt candelabra base bulbs
(supplied) into the light sockets.
Installation on Emerson Fans
Having a Modular Switch Cup with
Center Screw
1. Remove all parts and parts packages from the
carton.
COVER PLATE
MOTOR
CONNECTOR
2. Remove the switch cup from the cover plate by
removing the three screws around the side of the
switch cup (Figure 1).
SWITCH CUP
CONNECTOR
WIRE
CONNECTOR
BLACK WIRE
BLUE WIRE
HEX NUT
SCREWS
SWITCH CUP
3. Disconnect the motor connector from the switch
cup connector (Figure 1).
4. Remove the center screw from the switch cup
(Figure 1).
WHITE WIRES
LOCKWASHER
FAN SWITCH
CHAIN
RUBBER
WASHER
5. Carefully locate the white and blue wires (labeled
either "L" or "LIGHT") in the switch cup and
remove the wire connectors from the wires.
LIGHT
FITTER
6. Insert the black and white wires from the light fitter
through the center hole in the switch cup
(Figure 2) and thread the switch cup onto the light
fitter. Hold wires taut while installing switch cup to
prevent the wires from twisting. Tighten the fitter
until the fan switch chain aligns with the hole in the
fitter.
RUBBER
WASHER
HEX NUT
FAN SWITCH CHAIN
BOWL CAP
(FN200)
FINIAL (FN200)
Figure 2
MOTOR
CONNECTOR
SCREWS
COVER PLATE
SWITCH CUP
CONNECTOR
WARNING: To avoid possible fire or electrical
shock, make certain no bare wire strands are
exposed outside wire connectors.
Figure 3
SWITCH
CUP
CENTER SCREW
Figure 1
!
WARNING
To avoid possible fire or electric shock, be careful
not to pinch wires between switch cup and the cover
plate.
2
5. Connect the white wire from the ceiling fan to the
white wire of the light fitter. Connect the blue wire
from the ceiling fan to the black wire of the light
fitter. Use listed wire connectors (previously
removed in Step 3) to make connections. (Figures
5 and 6.)
NOTE: The FN200 finial pack (supplied) comes with
three options: no holes, one hole and two holes for pull
chain options.
12.
13.
Depending on the model purchased, insert the
fan speed control switch chain through the
offset hole in the glass bowl and the hole in the
bowl cap.
SWITCH
HOUSING
Gently place the glass bowl onto the light fixture
(Figure 4). Secure the glass by installing the
rubber washer and thin hex nut finger tight.
Then place the bowl cap onto the threaded light
fixture, route the fan speed control chain
through the outer hole and the fitter chain
through the center hole. Install and tighten the
finial nut onto the threaded light fixture (Figures
2 or 5).
FAN SWITCH
CHAIN
WHITE WIRE
WIRE
CONNECTORS
BLUE WIRE
BLACK WIRE
WHITE WIRE
HEX NUT
LOCKWASHER
COVER
SCREWS
RUBBER
WASHER
LIGHT
FITTER
RUBBER
WASHER
GLASS
BOWL
HEX NUT
FAN SWITCH
CHAIN
BOWL CAP
LIGHT KIT
CHAIN
COUPLING
FINIAL NUT
SPEED CONTROL
CHAIN
BOWL CAP
(FN200)
FINIAL (FN200)
Figure 5
COUPLING
WOOD
PENDANT
Figure 4
14.
15.
WOOD PENDANT
Connect the wood pendant (supplied) to the
switch pull chain by sliding the wood pendant
(small hole first) onto the pull chain. Attach the
chain coupling to the end of the chain and allow
the wood pendant to fall down over the
coupling.
WARNING: To avoid possible fire or electrical
shock, make certain no bare wire strands are
exposed outside wire connectors.
Figure 6
!
Connect the wood pendant (supplied) to the
light kit chain by sliding the wood pendant (small
hole first) onto the pull chain. Attach the chain
coupling to the end of the chain and allow the
wood pendant to fall down over the coupling.
To avoid possible fire or electrical shock, be careful
not to pinch wires between the switch housing and
the light fitter.
NOTE: The FN200 finial pack (supplied) comes with
three options: no holes, one hole and two holes for pull
chain options.
NOTE: It is advisable to periodically check the tightness of the finial.
6. Depending on the model purchased, insert the fan
speed control switch chain through the
offset hole in the glass bowl and the hole in the
bowl cap.
7 Carefully tuck all wires and splices into the switch
housing.
8. Install the cover and fitter assembly to the switch
housing by using the screws removed in Step 2.
9. Gently place the glass bowl onto the light fixture
(Figure 7). Then place the bowl cap onto the
threaded light fixture, route the fan speed control
chain through the outer hole and the fitter chain
through the center hole. Install and tighten the
finial nut onto the threaded light fixture (Figure 7).
Installation on Emerson Fans
Having Two-Piece Die-Cast
Switch Housings
1. Remove all parts and parts packages from carton.
2. Remove the cover from switch housing below
ceiling fan (Figure 5).
3. Carefully pull down white and blue wires from the
switch housing and remove wire connectors.
4. Thread the white and black wires of the light fitter
through the cover, lockwasher, hex nut and then
secure by using a wrench.
WARNING
3
10.
Install three 60-watt candelabra base bulbs
(supplied) into the light sockets.
11.
Connect the wood pendant (supplied) to the
switch pull chain by sliding the wood pendant
(small hole first) onto the pull chain. Attach the
chain coupling to the end of the chain and allow
the wood pendant to fall down over the
coupling.
12.
Connect the wood pendant (supplied) to the
light kit chain by sliding the wood pendant (small
hole first) onto the pull chain. Attach the chain
coupling to the end of the chain and allow the
wood pendant to fall down over the coupling.
GLASS
BOWL
BOWL CAP
LIGHT KIT
CHAIN
COUPLING
FINIAL NUT
SPEED CONTROL
CHAIN
COUPLING
WOOD
PENDANT
Figure 7
WOOD PENDANT
LIMITED WARRANTY
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original purchaser
or user of the product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED
TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR
OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of
Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorize
service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Light
Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no
employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT
RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are
not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Air Comfort Products
Part No. F40BP74420001
Revision: 130402
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Form No. BP7442-1
Printed in China 04/13