READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan
Light Fixture
Owner’s Manual
Net Weight:
4.5
Lbs.
Model Number:
LK180
Four 13-Watt CFL Medium Base Bulbs
Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service
8 a.m. - 6 p.m., Eastern, Monday-Friday
1-800-654-3545
www.emersonfans.com
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1.Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for
future reference.
2.Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing
or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3.Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1.To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker
box before wiring.
2.Make certain no bare wires are exposed outside the wire connectors.
3.All wiring must conform to national and local electrical codes.
4.Follow the recommended instructions for the proper method of wiring your new light fixture. If you
feel you do not have enough electrical wiring knowledge or experience, have your light fixture
installed by a licensed electrician. Any electrical work not described in this manual should be
performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson CF
Series Ceiling Fans in indoor locations. This light kit is not to be used on Emerson CF Series Ceiling
Fans installed in damp or wet locations.
Part No. F40BP74860000
Revision: 131112
Form No. BP7486
ETL Model Nos.: LK180
7. Insert the black and white wires through the lockwasher and hex nut (supplied), firmly tighten the
hex nut to secure the light kit fitter to the switch
cup. Connect the white wire from the switch cup
to the white wire of the light fitter (Figure 2).
Connect the blue wire from the switch cup to the
black wire of the light fitter. Use listed wire
connectors (previously removed in Step 5) to
make connections (Figures 2 and 3).
8. Carefully tuck all wires and splices into the switch
cup. (Figure 2.)
9. Connect the motor connector to the switch cup
connector.
10. Position the cup/light fitter in the cover plate and
install the three screws that were previously
removed in Step 2 and tighten securely.
Assembly and Installation
!
WARNING
Do not install or use the light fixture if any part
is missing or damaged. Contact your dealer for
replacement.
!
WARNING
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring.
11. The light sockets are equipped to take four
13-watt CFL medium base bulbs.
Installation on Emerson Fans
Having a Modular Switch Cup with
Center Screw
COVER PLATE
1. Remove all parts and parts packages from the
carton.
MOTOR
CONNECTOR
2. Remove the switch cup from the cover plate by
removing the three screws around the side of the
switch cup (Figure 1).
SWITCH CUP
CONNECTOR
BLACK WIRE
3. Disconnect the motor connector from the switch
cup connector (Figure 1).
BLUE WIRE
HEX NUT
SCREWS
4. Remove the center screw from the switch cup
(Figure 1).
SWITCH CUP
5. Carefully locate the white and blue wires (labeled
either "L" or "LIGHT") in the switch cup and
remove the wire connectors from the wires.
LIGHT FITTER
6. Insert the black and white wires from the light fitter
through the center hole in the switch cup
(Figure 2) and thread the switch cup onto the light
fitter. Hold wires taut while installing switch cup to
prevent the wires from twisting. Tighten the fitter
until the fan switch chain aligns with the hole in the
fitter.
FILTER FLANGE
RUBBER
WASHER
HEX NUT
WIRE
CONNECTOR
WHITE WIRES
LOCKWASHER
FAN SWITCH
CHAIN
FAN SWITCH
CHAIN
FINIAL (FN200
BOWL CAP
(FN200)
Figure 2
MOTOR
CONNECTOR
SCREWS
COVER PLATE
WARNING: To avoid possible fire or electrical
shock, make certain no bare wire strands are
exposed outside wire connectors.
SWITCH CUP
CONNECTOR
Figure 3
SWITCH
CUP
!
CENTER SCREW
Figure 1
WARNING
To avoid possible fire or electric shock, be careful
not to pinch wires between switch cup and the cover
plate.
2
ETL Model No.: LK180
NOTE: The FN200 finial pack comes with three options:
no holes, one hole and two holes for pull chain options.
12.
13.
FAN SWITCH
CHAIN
SWITCH
HOUSING
Depending on the fan model, insert the fan
speed control switch chain through the
offset hole in the glass bowl and the hole in the
bowl cap.
WHITE WIRE
BLUE
WIRE
Gently place the glass bowl onto the light fixture
(Figure 4). Secure the glass by installing the
rubber washer and thin hex nut finger tight.
Then place the bowl cap onto the threaded light
fixture, route the fan speed control chain
through the outer hole and the light fitter control
chain through the center hole. Install and tighten
the finial nut onto the threaded light fixture
(Figure 2).
WIRE
CONNECTORS
WHITE WIRE
BLACK
WIRE
HEX NUT
LOCKWASHER
COVER
SCREWS
LIGHT FITTER
FILTER FLANGE
RUBBER
WASHER
HEX NUT
FAN SWITCH
CHAIN
FINIAL (FN200)
BOWL CAP
(FN200)
Figure 5
GLASS
SHADE
RUBBER WASHER
HEX NUT
BOWL CAP
FINIAL NUT
COUPLING (2)
FAN SPEED CONTROL CHAIN
LIGHT FITTER CONTROL CHAIN
WOOD PENDANT (2)
WARNING: To avoid possible fire or electrical
shock, make certain no bare wire strands are
exposed outside wire connectors.
Figure 4
14.
Connect the wood pendant (supplied) to the
switch pull chain by sliding the wood pendant
(small hole first) onto the pull chain. Attach the
chain coupling to the end of the chain and allow
the wood pendant to fall down over the
coupling.
Figure 6
!
WARNING
To avoid possible fire or electrical shock, be careful
not to pinch wires between the switch housing and
the light fitter.
NOTE: It is advisable to periodically check the tightness of the finial.
NOTE: The FN200 finial pack comes with three options:
no holes, one hole and two holes for pull chain options.
Installation on Emerson Fans
Having Two-Piece Die-Cast
Switch Housings
6. Depending on the model purchased, insert the fan
speed control switch chain through the
offset hole in the glass bowl and the hole in the
bowl cap.
1. Remove all parts and parts packages from carton.
7 Carefully tuck all wires and splices into the switch
housing.
2. Remove the cover from switch housing below
ceiling fan (Figure 5).
8. Install the cover and fitter assembly to the switch
housing by using the screws removed in Step 2.
3. Carefully pull down white and blue wires from the
switch housing and remove wire connectors.
9. Gently place the glass bowl onto the light fixture
(Figure 7). Secure the glass by installing the
rubber washer and thin hex nut finger tight.
Then place the bowl cap onto the threaded light
fixture, route the fan speed control chain through
the outer hole and the light fitter control chain
through the center hole. Install and tighten the
finial nut onto the threaded light fixture (Figure 5).
4. Thread the white and black wires of the light fitter
through the cover, lockwasher, hex nut and then
secure by using a wrench.
5. Connect the white wire from the ceiling fan to the
white wire of the light fitter. Connect the blue wire
from the ceiling fan to the black wire of the light
fitter. Use listed wire connectors (previously
removed in Step 3) to make connections. (Figures
5 and 6.)
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: LK180
10. The light sockets are equipped to take four
13-watt CFL medium base bulbs.
GLASS
SHADE
RUBBER WASHER
HEX NUT
BOWL CAP
FINIAL NUT
COUPLING (2)
11. Connect the wood pendant (supplied) to the
switch pull chain by sliding the wood pendant
(small hole first) onto the pull chain. Attach the
chain coupling to the end of the chain and allow
the wood pendant to fall down over the coupling.
FAN SPEED CONTROL CHAIN
LIGHT FITTER CONTROL CHAIN
WOOD PENDANT (2)
Figure 7
LIMITED WARRANTY
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original
purchaser or user of the product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS
ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR
RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products,
Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with
your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorize
service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your
Emerson Light Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties
apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT
RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include
but are not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of
repairing or replacing other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
Air Comfort Products
Part No. F40BP74860000
Revision: 131112
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Form No. BP7486
Printed in China 11/13
ETL Model No.: LK180