Installation of Glass Bowl
!
FAN SWITCH
CHAIN
WARNING
To avoid fire hazard, do not exceed three
60-watt (max.) candelabra base light bulbs.
1. Install a 60-watt (max.) candelabra base
light bulb (not included) into each of the
three lamp holder sockets (Figure 6).
2. Remove the bottom nut(1), the rubber
washer(4) and the ring nut(3) from the light
fitter(8).
3. Place the glass bowl(6) onto the threaded
nipple(7). Align the fan chain with the small
hole on the glass bowl. Position the rubber
washer(4) and the ring nut(3) onto the
threaded nipple and tighten finger tight.
4. Install the wire bound bowl holder(6) by
positioning the bowl holder against the
bottom of the glass bowl(6) on the threaded
nipple(7). Align the small hole in the guide
plate.
5. Guide the light switch chain through the
bottom nut. Tighten the bottom nut onto the
threaded nipple finger tight.
6. Place the chain from the fan speed switch
through the small hole in the glass bowl and
guide plate.
7. Attach the extension chain (supplied with the
light kit) to the fan speed switch chain.
READ AND SAVE THESE INSTRUCTIONS
(8) LIGHT FITTER
(7) THREADED NIPPLE
NOTE: YOUR LIGHT KIT
MAY NOT RESEMBLE
THE ONE PICTURED
HERE.
(6) GLASS
BOWL
Wire Bound Bowl
Model LK31
(2) GUIDE PLATE
(1) BOTTOM NUT
Figure 6
LIGHT SWITCH
CHAIN
(5) WIRE BOUND
BOWL HOLDER
(4) RUBBER WASHER
(3) RING NUT
SUITABLE FOR DAMP LOCATIONS
THREE 60-WATT CANDELABRA BULBS
PENDANTS (2)
CAUTION: Never use pliers to tighten
bottom nut against the bowl. A broken or
damage bowl will most surely result.
8. Turn on power at the main fuse or circuit
breaker box.
NOTE: It is advisable to periodically check
the tightness of the bottom nut. Fan
operation may loosen this nut.
Low Profile Damp Light
Model LK53
SUITABLE FOR DAMP LOCATIONS
THREE 60-WATT CANDELABRA BULBS
!
LIMITED WARRANTY
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original purchaser or
user of the product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED
TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE
PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR
OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of
Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Light
Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no
employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT
RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not
limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing
other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
DIVISION OF EMERSON ELECTRIC CO.
Air Comfort Products 8100 W. Florissant ¥ St. Louis, MO 63136
Part No. BP7226-1
Form No. F40BP72260001
Printed in China 12/06
Ceiling Fan
Light Fixture
Owner's
Manual
Net Weight:
5.3
Lbs.
UL
®
WARNING
Safety Instructions
To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's
Manual for future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Before installing or servicing the light fixture or ceiling fan, switch power off at
service panel and lock service panel disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a warning device, such as a tag, to the service panel.
3. Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or
circuit breaker box before wiring.
2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to national and local electrical codes.
4. Follow the recommended instructions for the proper method of wiring your new light
fixture. If you feel you do not have enough electrical wiring knowledge or experience,
have your light fixture installed by a licensed electrician. Any electrical work not
described in this manual should be performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on
Emerson Model CF652, CF653, CF670, CF680, CF742 and CF2000 Ceiling Fans installed
in damp locations. Permissible to use this light kit on all CF and F Series Ceiling Fans
installed in indoor locations.
Form No. F40BP72260000
Part No. BP7226-1
U.L. Model No.: LK31/LK53
5. Carefully locate the white and blue
wires (labeled either "L" or "LIGHT") in
the switch cup and remove the wire
connectors from the wires.
6. Insert the black and white wires from
the light fitter(7) through the center hole
in the switch cup (Figure 2) and thread
the switch cup onto the light fitter. Hold
wires taut while installing switch cup to
prevent the wires from twisting.
Securely tighten the fitter to the switch
cup.
7. Insert the black and white wires through
the lockwasher(7) and hex nut(8)
supplied. Firmly tighten the hex nut to
secure the light kit fitter to the switch
cup.
8. Connect the white wire from the switch
cup to the white wire of the light fitter
(Figure 2). Connect the blue wire from
the switch cup to the black wire of the
light fitter. Use listed wire connectors
(previously removed in step 5) to make
connections (Figures 2 and 3).
Assembly and Installation
!
WARNING
Do not install or use the fixture if any
part is missing or damaged. Contact
your dealer for replacement.
NOTE: For installation on Emerson
fans with a center screw in modular
(detachable) switch cup, proceed to
step 1, page 2. For fans with center
screw in switch housing cover,
proceed to step 1, page 3.
Installation on Emerson Fans with
a Center Screw and with Modular
(Detachable) Switch Cups
1. Remove all parts and parts packages
from the carton.
!
WARNING
To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.
(4) MOTOR
CONNECTOR
BLUE WIRE
BLACK WIRE
(3) SCREWS
(9) HEX NUT
(8) LOCKWASHER
(1) SWITCH
CUP
4. Remove the center screw(6) from the
switch cup (Figure 1).
(7) LIGHT
FITTER
(2) COVER PLATE
(5) SWITCH CUP
CONNECTOR
(6) WIRE
CONNECTORS
WHITE WIRES
FAN SWITCH
CHAIN
NOTE: YOUR FITTER
MAY NOT LOOK THE
SAME AS THE ONE IN
THIS ILLUSTRATION.
HOWEVER, IT
INSTALLS IN A
SIMILAR MANNER.
Figure 2
(3) SCREWS
(1) SWITCH HOUSING
ASSEMBLY
FAN SWITCH
CHAIN
WARNING
(3) WIRE
CONNECTORS
BLUE WIRE
To avoid possible fire or electrical
shock, make certain no bare wire
strands are exposed outside wire
connectors.
Figure 3
!
WHITE WIRES
(8) HEX NUT
(7) LOCKWASHER
BLACK WIRE
(5) COVER
(2) SCREWS
(4) CENTER
SCREW
(6) LIGHT FITTER
WARNING
Figure 4
To avoid possible fire or electric shock,
be careful not to pinch wires between
switch cup and the cover plate.
6. Connect the white wire from the ceiling
fan to the white wire of the light kit
fitter(6). Connect the blue wire from the
ceiling fan to the black wire of the light
kit fitter. Use listed wire connectors(3)
(previously removed in step 3) to make
connections. (Figures 4 and 5.)
12. Proceed to “Installation of Glass Bowl”
section.
Installation on Emerson Fans
With Center Screw in Switch
Housing Cover
(Not Modular Switch Cup)
!
WARNING
1. Remove all parts and parts packages
from carton.
2. Remove the switch cup(1) from the
cover plate(2) by removing the three
screws(3) around the side of the switch
cup (Figure 1).
3. Disconnect the motor connector(4)
from the switch cup connector(5)
(Figure 1).
(4) MOTOR
CONNECTOR
!
(2) COVER PLATE
9. Carefully tuck all wires and splices
into the switch cup(1). (Figure 2.)
10. Connect the motor connector(4) to the
switch cup connector(5).
11. Position the cup/light fitter(1)(7) on the
cover plate(2) and install the three
screws(3) that were previously removed
in step 2 and tighten securely.
(5) SWITCH CUP
CONNECTOR
(1) SWITCH
CUP
(6) CENTER SCREW
Figure 1
2
!
To avoid possible fire or electrical
shock, make certain no bare wire
strands are exposed outside wire
connectors.
WARNING
To avoid possible electric shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
Figure 5
7. Carefully tuck all wires and splices into
the switch housing(1).
8. Attach the cover/light fitter(5)(6) to the
switch assembly housing(1) using the
two screws(2) that were removed in
Step 2) (Figure 4.)
2. Remove the cover from fan switch
housing(1) by removing the two outer
screws(2). (See Figure 4).
3. Remove the center screw(4) in the
switch housing cover(5). Insert the
black and white wires from the light kit
fitter(6) thru the hole and thread the
switch housing cover tightly onto the
light kit fitter.
4. Insert the black and white wires through
the lockwasher(7) and hex nut(8)
supplied. Firmly tighten the hex nut to
secure the light kit fitter to the switch
cup.
5. Carefully pull down the white and blue
wires from the switch housing(1) and
remove the wire connectors.
!
WARNING
To avoid fire or electrical shock, be
careful not to pinch wires between
the switch housing assembly and
the cover.
9. Proceed to “Installation of Glass Bowl”
section.
3