advertisement
User’s Manual for ELPLL02 Long-Focal Length Zoom Lens
•
This long-focal length zoom lens is designed for use only with EPSON multimedia projectors.
•
It makes it possible to increase the distance between the projector and the screen.
•
Please read this manual completely before use to assure maximum performance.
•
Note that illustrations may differ slightly from your actual product.
•
Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent damage or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and optimum performance.
Warning
Ignoring this warning, or implementing the content incorrectly, could result in injury or even death.
Memo Important information, such as additional explanations, key points to remember, and things to avoid doing.
9
01.2.15, 4:20 PM Adobe PageMaker 6.0J/PPC 02_LTZL_DTP_E.pm6
Page 9
1. Before mounting the zoom lens
1-1 Safety precautions
Warning
Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
•
Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Zoom lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove mounting screws
•
In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits the screws properly.
10
02_LTZL_DTP_E.pm6
Page 10 01.2.15, 4:20 PM Adobe PageMaker 6.0J/PPC
2. Mounting the zoom lens
Warning
Be sure to disconnect the power cable before installation, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause damage.
•
Note that the illustrations below may not match your particular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
02_LTZL_DTP_E.pm6
Page 11
Screws (two)
11
01.2.15, 4:20 PM Adobe PageMaker 6.0J/PPC
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens.
Current lens
2-2 Mounting the zoom lens
(1) Mounting the zoom lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top.
Seal
12
02_LTZL_DTP_E.pm6
Rear lens cap
Page 12 01.2.15, 4:20 PM Adobe PageMaker 6.0J/PPC
(2) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
•
Turn on the power and verify that the projector operates normally.
Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat.
02_LTZL_DTP_E.pm6
Page 13
13
01.2.15, 4:20 PM Adobe PageMaker 6.0J/PPC
4. Zoom lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
68.3 to 116.2 mm
1.7 x
2.14 to 2.98
60 to 300 inches
2100 g
4-2 Appearance with zoom lens mounted
About 505mm
02_LTZL_DTP_E.pm6
Page 15
15
01.2.15, 4:20 PM Adobe PageMaker 6.0J/PPC
User’s Manual for Long Throw Zoom Lens ELPLL03
•
This long throw zoom lens is designed for use only with EPSON multimedia projectors.
•
It makes it possible to increase the distance between the projector and the screen.
•
Please read this manual completely before use to assure maximum performance.
•
Note that illustrations may differ slightly from your actual product.
•
Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent damage or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and optimum performance.
Warning
Ignoring this warning, or implementing the content incorrectly, could result in injury or even death.
Memo Important information, such as additional explanations, key points to remember, and things to avoid doing.
9
01.2.15, 4:23 PM Adobe PageMaker 6.0J/PPC 02_LTZL_DTP_E.pm6
Page 9
1. Before mounting the zoom lens
1-1 Safety precautions
Warning
Be sure to screw the Long throw zoom lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
•
Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Zoom lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove mounting screws
•
In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits the screws properly.
10
02_LTZL_DTP_E.pm6
Page 10 01.2.15, 4:23 PM Adobe PageMaker 6.0J/PPC
2. Mounting the zoom lens
Warning
Be sure to disconnect the power cable before installation, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause damage.
•
Note that the illustrations below may not match your particular projector model.
2-1 Remove the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
02_LTZL_DTP_E.pm6
Page 11
Screws (two)
11
01.2.15, 4:23 PM Adobe PageMaker 6.0J/PPC
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens.
Current lens
2-2 Mounting the zoom lens
(1) Mounting the zoom lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top.
Seal
12
02_LTZL_DTP_E.pm6
Rear lens cap
Page 12 01.2.15, 4:23 PM Adobe PageMaker 6.0J/PPC
(2) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
•
Turn on the power and verify that the projector operates normally.
Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat.
02_LTZL_DTP_E.pm6
Page 13
13
01.2.15, 4:23 PM Adobe PageMaker 6.0J/PPC
4. Zoom lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
144.1 to 194.5mm
1.35 x
2.60 to 3.27
80 to 300 inches
2100 g
4-2 Appearance with zoom lens mounted
About 505mm
02_LTZL_DTP_E.pm6
Page 15
15
01.2.15, 4:23 PM Adobe PageMaker 6.0J/PPC
User’s Manual for ELPLR01 Rear Projector wide Lens
•
This wide-angle lens is designed for use only on EPSON multimedia projectors.
•
This lens is designed for use only on rear projection and rear projection box systems.
•
Please read this manual completely before use to assure maximum performance.
•
Note that illustrations may differ slightly from your actual product.
•
Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent damage or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and optimum performance.
Warning
Ignoring this warning, or implementing the content incorrectly, could result in injury or even death.
Memo Important information, such as additional explanations, key points to remember, and things to avoid doing.
11
01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC 02_RPWL_DTP_E.pm6
Page 11
1. Before mounting the wide-angle lens
1-1 Safety precautions
Warning
Be sure to screw the Rear Projector wide lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
•
Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Zoom lens
Screwdriver
Front lens cap
Used to tighter/remove mounting screws
Hex wrench
User’s manual (this document)
Used to loosen and tighten the ring mounting screws.
•
In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits the screws properly.
12
02_RPWL_DTP_E.pm6
01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC Page 12
2. Mounting the rear-projection wide-angle lens
Warning
Be sure to disconnect the power cable before installation, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause damage.
•
Note that the illustrations below may not match your particular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
02_RPWL_DTP_E.pm6
Page 13
Screws (two)
13
01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens.
Current lens
2-2 Mounting the rear-projection wide-angle lens
(1) Mounting the rear-projection wide-angle lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the rear projector wide lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top.
Seal
14
02_RPWL_DTP_E.pm6
Rear lens cap
Page 14 01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC
(2) Adjusting the wide lens for a rear projector
•
This lens must be adjusted to match the screen size. Adjust the lens as follows, before installing the front case.
1. Turn the lens shift button to move the lens all the way down.
2. Loosen the 2 focus ring mounting screws by using the hex wrench that came in the same package.
3. Loosen the 2 resolving plane correction ring mounting screws with the hex wrench.
4. Turn on the projector power.
5. Rotate the two rings to adjust the image to the optimum appearance. The resolving plane correction ring should provide a sharp image across the entire screen area.
6. Use the hex wrench to retighten the four ring mounting screws.
7. Turn off the power, and disconnect the power cable.
Lens shift button
WARNING
DO NOT TOUCH!
Resolving plane correction ring
Focus ring
Focus ring mounting screws Resolving plane correction ring mounting screws
Warning
Turn the power only when adjusting the lens. Always disconnect the power cable at other times.
When adjusting the lens, take care not to touch any other parts of the projector or lens, as there is a danger of electric shock with the front case open.
Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat.
15
02_RPWL_DTP_E.pm6
01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC Page 15
(3) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
•
Turn on the power and verify that the projector operates normally.
16
02_RPWL_DTP_E.pm6
Page 16 01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC
4. Rear-projection wide-angle lens specifications
4-1 Lens specifications
1. Focal length
2. f number
3. Projection size
4. Mass
27mm
2.3
60 to 100 inches
1600 g
4-2 Appearance with rear projector wide lens mounted
About 455mm
18
02_RPWL_DTP_E.pm6
Page 18 01.2.15, 4:17 PM Adobe PageMaker 6.0J/PPC
User’s Manual for ELPLS01 Standard Lens
•
This standard lens is designed for use only with EPSON multimedia projectors.
•
Please read this manual completely before use to assure maximum performance.
•
Note that illustrations may differ slightly from your actual product.
•
Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent damage or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and optimum performance.
Warning
Ignoring this warning, or implementing the content incorrectly, could result in injury or even death.
Memo Important information, such as additional explanations, key points to remember, and things to avoid doing.
02_SL_DTP_E.pm6
Page 9
9
01.2.15, 4:19 PM Adobe PageMaker 6.0J/PPC
1. Before mounting the standard lens
1-1 Safety precautions
Warning
Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
•
Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Standard lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove mounting screws
•
In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits the screws properly.
10
02_SL_DTP_E.pm6
Page 10 01.2.15, 4:19 PM Adobe PageMaker 6.0J/PPC
2. Mounting the standard lens
Warning
Be sure to disconnect the power cable before installation, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause damage.
•
Note that the illustrations below may not match your particular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
02_SL_DTP_E.pm6
Page 11
Screws (two)
11
01.2.15, 4:19 PM Adobe PageMaker 6.0J/PPC
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens.
Current lens
2-2 Mounting the standard lens
(1) Mounting the standard lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the standard lens with the four mounting screws. Be sure that the seal reading “UP-
PER” is on top.
Seal
12
02_SL_DTP_E.pm6
Rear lens cap
Page 12 01.2.15, 4:19 PM Adobe PageMaker 6.0J/PPC
(2) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
•
Turn on the power and verify that the projector operates normally.
Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat.
02_SL_DTP_E.pm6
Page 13
13
01.2.15, 4:19 PM Adobe PageMaker 6.0J/PPC
4. Standard lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
49.2 to 68.9 mm
1.4 x
1.84 to 2.36
30 to 300 inches
1300 g
4-2 Appearance with standard lens mounted
About 475mm
02_SL_DTP_E.pm6
Page 15
15
01.2.15, 4:19 PM Adobe PageMaker 6.0J/PPC
User's Manual for the ELPLW01 Wide Zoom Lens
•
This wide zoom lens is designed for use only with EPSON multimedia projectors.
•
It makes it possible to decrease the distance between the projector and the screen.
•
Please read this manual completely before use to assure maximum performance.
•
Note that illustrations may differ slightly from your actual product.
•
Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent damage or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and optimum performance.
Warning
Ignoring this warning, or implementing the content incorrectly, could result in injury or even death.
Memo Important information, such as additional explanations, key points to remember, and things to avoid doing.
9
01.2.15, 4:22 PM Adobe PageMaker 6.0J/PPC 02_STZL_DTP_E.pm6
Page 9
1. Before mounting the zoom lens
1-1 Safety precautions
Warning
Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
•
Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Zoom lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove mounting screws
•
In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits the screws properly.
10
02_STZL_DTP_E.pm6
Page 10 01.2.15, 4:22 PM Adobe PageMaker 6.0J/PPC
2. Mounting the zoom lens
Warning
Be sure to disconnect the power cable before installation, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause damage.
•
Note that the illustrations below may not match your particular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the three mounting screws, and pull off the front case.
The two components will separate from each other.
Front case
02_STZL_DTP_E.pm6
Page 11
Screws (three)
11
01.2.15, 4:22 PM Adobe PageMaker 6.0J/PPC
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens.
Current lens
2-2 Mounting the zoom lens
(1) Mounting the zoom lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading "UPPER" is on top.
Seal
12
02_STZL_DTP_E.pm6
Rear lens cap
Page 12 01.2.15, 4:22 PM Adobe PageMaker 6.0J/PPC
(2) Mounting the front case
1. Set the front case into position and tighten the three screws.
This completes installation.
•
Turn on the power and verify that the projector operates normally.
Memo •
Be sure to remove the front lens cap before turning on the power, or it may melt from the heat.
•
When handling the zoom lens, take care not to catch your finger between the lens and the tabletop.
02_STZL_DTP_E.pm6
Page 13
13
01.2.15, 4:22 PM Adobe PageMaker 6.0J/PPC
4. Zoom lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
37.9 to 45.5 mm
1.2 x
2.34 to 2.65
60 to 200 inches
2600 g
4-2 Appearance with zoom lens mounted
About 480mm
02_STZL_DTP_E.pm6
Page 15
15
01.2.15, 4:22 PM Adobe PageMaker 6.0J/PPC
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project