PowerLite® 1760W/1770W/1775W
Quick Setup
Camera, USB Device, or Epson Document Camera
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera to the projector’s USB TypeA (flat) port.
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Connect the projector
Adjust the image
Using the remote control
1
If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Make sure the batteries are installed as shown (two AA batteries).
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
Choose from the following connections:
Computer USB Port
Connect a computer using the USB cable that came with the projector.
Connect the square end of the USB cable to the projector’s �
USB TypeB
port. Connect the flat end of the cable to any USB port on your computer.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the User’s Guide and EasyMP Slide
Converter Operation Guide on your projector CD for details.
Turn on your equipment
Windows®: After turning on the projector, follow the on-screen instructions
to install the Epson USB Display software (EMP_UDSE.EXE; only on first
connection).
1
2
Turn on your computer or video source.
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
3
PowerLite 1775W: Press the Focus buttons to sharpen the image.
PowerLite 1760W/1770W: Rotate the focus ring to sharpen the image.
Turn off projector
display and sound
Control projector volume
PowerLite
1775W
Access projector menus
PowerLite
1760W/1770W
4
Navigate
projector menus
Turn the zoom ring to reduce or enlarge the image.
PowerLite
1775W
The power light on the projector turns orange.
3
Open the A/V Mute slide all the way.
Connect one end of the cable to the projector’s Computer port, and the
other end to your computer’s �
monitor port. If you are using a notebook,
switch it to external display (see “Troubleshooting”). You can also connect an
audio cable.
5
4
Press the
power button on the projector or remote control.
Power button
Wireless Network
You can connect the projector wirelessly over an 802.11g, 802.11b, or 802.11n
wireless network. See “Projecting wirelessly” for instructions.
For more information on using the remote control, see the User’s Guide on
your projector CD.
PowerLite
1760W/1770 W
6
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11g,
802.11b, or 802.11n wireless network. Your computer must have a wireless
card or built-in wireless interface, and be running Windows 7, Windows
Vista®, Windows XP Professional x64, Windows XP, or Windows 2000, or
Mac OS® X 10.3 to 10.6.
1
2
Turn off the projector and unplug the power cord.
3
Remove the wireless LAN module cover.
To install the LAN module, turn the projector over and remove the screw
securing the LAN module cover.
Power light
Video Device
Connect up to 3 video devices and use the Source Search button on the
projector or remote control to switch between them.
RCA video cable (composite video)
(optional)
Component video to VGA cable
(optional)
Audio cable
(optional)
HDMI cable
(optional)
*411958700*
*411958700*
Choose which
source to display
Plug in the projector.
Note: If the software screen does not display automatically, open My
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not
display, access the projector’s Extended menu and select USB Display as the
USB Type B setting. See the User’s Guide on your projector CD for instructions.
Macintosh®: After turning on the projector, the setup folder for USB Display
appears in the Finder. Double-click USB Display Installer and follow the
on-screen instructions to install the Epson USB Display software (only on first
connection).
Turn projector
on and off
The power light flashes green, then stays on.
Note: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
PowerLite® 1760W/1770W/1775W
Quick Setup
Camera, USB Device, or Epson Document Camera
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera to the projector’s USB TypeA (flat) port.
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Connect the projector
Adjust the image
Using the remote control
1
If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Make sure the batteries are installed as shown (two AA batteries).
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
Choose from the following connections:
Computer USB Port
Connect a computer using the USB cable that came with the projector.
Connect the square end of the USB cable to the projector’s �
USB TypeB
port. Connect the flat end of the cable to any USB port on your computer.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the User’s Guide and EasyMP Slide
Converter Operation Guide on your projector CD for details.
Turn on your equipment
Windows®: After turning on the projector, follow the on-screen instructions
to install the Epson USB Display software (EMP_UDSE.EXE; only on first
connection).
1
2
Turn on your computer or video source.
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
3
PowerLite 1775W: Press the Focus buttons to sharpen the image.
PowerLite 1760W/1770W: Rotate the focus ring to sharpen the image.
Turn off projector
display and sound
Control projector volume
PowerLite
1775W
Access projector menus
PowerLite
1760W/1770W
4
Navigate
projector menus
Turn the zoom ring to reduce or enlarge the image.
PowerLite
1775W
The power light on the projector turns orange.
3
Open the A/V Mute slide all the way.
Connect one end of the cable to the projector’s Computer port, and the
other end to your computer’s �
monitor port. If you are using a notebook,
switch it to external display (see “Troubleshooting”). You can also connect an
audio cable.
5
4
Press the
power button on the projector or remote control.
Power button
Wireless Network
You can connect the projector wirelessly over an 802.11g, 802.11b, or 802.11n
wireless network. See “Projecting wirelessly” for instructions.
For more information on using the remote control, see the User’s Guide on
your projector CD.
PowerLite
1760W/1770 W
6
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11g,
802.11b, or 802.11n wireless network. Your computer must have a wireless
card or built-in wireless interface, and be running Windows 7, Windows
Vista®, Windows XP Professional x64, Windows XP, or Windows 2000, or
Mac OS® X 10.3 to 10.6.
1
2
Turn off the projector and unplug the power cord.
3
Remove the wireless LAN module cover.
To install the LAN module, turn the projector over and remove the screw
securing the LAN module cover.
Power light
Video Device
Connect up to 3 video devices and use the Source Search button on the
projector or remote control to switch between them.
RCA video cable (composite video)
(optional)
Component video to VGA cable
(optional)
Audio cable
(optional)
HDMI cable
(optional)
*411958700*
*411958700*
Choose which
source to display
Plug in the projector.
Note: If the software screen does not display automatically, open My
Computer or Computer, then double-click EPSON_PJ_UD. If it still does not
display, access the projector’s Extended menu and select USB Display as the
USB Type B setting. See the User’s Guide on your projector CD for instructions.
Macintosh®: After turning on the projector, the setup folder for USB Display
appears in the Finder. Double-click USB Display Installer and follow the
on-screen instructions to install the Epson USB Display software (only on first
connection).
Turn projector
on and off
The power light flashes green, then stays on.
Note: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
4
Insert the wireless LAN module into the port.
12 Select the Wireless LAN menu and press Enter.
Troubleshooting
Where to get help
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•Make sure the power light on the projector is green and not flashing, and
5
the A/V Mute slide is open.
Replace the cover and secure it using the screw.
•
Press the Source Search button on the projector or the remote control to
select the computer as the image source.
•
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7).
13 Select the Connection Mode setting and choose one of these options:
•
Quick to connect the projector to one computer on the network
•Advanced to connect the projector to multiple computers on
6
7
Plug in and turn on the projector.
•If you’re using the optional Quick Wireless Connection USB key
(included with the PowerLite 1775W), insert it into the projector’s
USB TypeA port, wait for the displayed message, remove the key,
and connect it to a USB port on your computer. Follow the on-screen
instructions to install the driver, then run your presentation. For
details, see the User’s Guide on your projector CD.
To configure your projector for your wireless network, do one of
the following:
•
8
Press the Menu button on the remote control, select the Network
menu, and press Enter.
If you’re not using the key, continue with these steps.
the network
14 If you selected Quick connection mode, select the Channel setting for
your wireless network and turn on the SSID Auto Setting setting.
15 Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
16 If you selected Advanced connection mode, enter your network SSID (up
to 32 characters) as the SSID setting.
17 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address, as
needed.
18 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
19 See the next section for additional instructions.
•
If the projector and notebook don’t display the
same image...
Windows
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
9 Choose Network Configuration and press Enter.
10 Select the Basic menu and press Enter.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is
installed along with your projector User’s Guide.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 am to 6 pm, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6
Monday through Friday
am
to 6
pm,
Pacific Time,
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
1
Windows 7: From the Windows Control Panel, select Display > Change
display settings.
Windows Vista: Right-click on the desktop and select Personalize >
Display Settings.
Optional accessories
Windows XP: From the Windows Control Panel, select Display >
Settings > Advanced.
For a list of optional accessories, see your projector User’s Guide.
2
The method for adjusting the monitor setting varies. You may need to
click the Monitor tab or icon, and then enable the external monitor
port or set it as your primary display. Check the Windows Help utility for
details.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software for
Meeting & Presentation to install the program.
On a Macintosh, select the Mirror Displays setting as described below.
For more information about using the projector, install the manuals from your
projector CD. View the guides by clicking the icons for them on your computer
desktop.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
Mac OS X
1
2
3
Select System Preferences, then select Display or Displays.
Select Detect Displays.
Mac OS X 10.6.x: Click Show displays in menu bar.
Other Mac OS X versions: Select the VGA Display or Color LCD
option, click the Arrangement or Arrange tab, and check the Mirror
Displays checkbox. (See your laptop manual for details.)
11 Select the Projector Name setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the User’s Guide on the projector CD for information on
adding passwords.
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2010 Epson America, Inc. 8/10
Printed in XXXXXX
CPD-28070
4
Insert the wireless LAN module into the port.
12 Select the Wireless LAN menu and press Enter.
Troubleshooting
Where to get help
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•Make sure the power light on the projector is green and not flashing, and
5
the A/V Mute slide is open.
Replace the cover and secure it using the screw.
•
Press the Source Search button on the projector or the remote control to
select the computer as the image source.
•
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7).
13 Select the Connection Mode setting and choose one of these options:
•
Quick to connect the projector to one computer on the network
•Advanced to connect the projector to multiple computers on
6
7
Plug in and turn on the projector.
•If you’re using the optional Quick Wireless Connection USB key
(included with the PowerLite 1775W), insert it into the projector’s
USB TypeA port, wait for the displayed message, remove the key,
and connect it to a USB port on your computer. Follow the on-screen
instructions to install the driver, then run your presentation. For
details, see the User’s Guide on your projector CD.
To configure your projector for your wireless network, do one of
the following:
•
8
Press the Menu button on the remote control, select the Network
menu, and press Enter.
If you’re not using the key, continue with these steps.
the network
14 If you selected Quick connection mode, select the Channel setting for
your wireless network and turn on the SSID Auto Setting setting.
15 Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
16 If you selected Advanced connection mode, enter your network SSID (up
to 32 characters) as the SSID setting.
17 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address, as
needed.
18 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
19 See the next section for additional instructions.
•
If the projector and notebook don’t display the
same image...
Windows
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
9 Choose Network Configuration and press Enter.
10 Select the Basic menu and press Enter.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is
installed along with your projector User’s Guide.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 am to 6 pm, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6
Monday through Friday
am
to 6
pm,
Pacific Time,
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
1
Windows 7: From the Windows Control Panel, select Display > Change
display settings.
Windows Vista: Right-click on the desktop and select Personalize >
Display Settings.
Optional accessories
Windows XP: From the Windows Control Panel, select Display >
Settings > Advanced.
For a list of optional accessories, see your projector User’s Guide.
2
The method for adjusting the monitor setting varies. You may need to
click the Monitor tab or icon, and then enable the external monitor
port or set it as your primary display. Check the Windows Help utility for
details.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software for
Meeting & Presentation to install the program.
On a Macintosh, select the Mirror Displays setting as described below.
For more information about using the projector, install the manuals from your
projector CD. View the guides by clicking the icons for them on your computer
desktop.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
Mac OS X
1
2
3
Select System Preferences, then select Display or Displays.
Select Detect Displays.
Mac OS X 10.6.x: Click Show displays in menu bar.
Other Mac OS X versions: Select the VGA Display or Color LCD
option, click the Arrangement or Arrange tab, and check the Mirror
Displays checkbox. (See your laptop manual for details.)
11 Select the Projector Name setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press Enter to
select them.
Note: See the User’s Guide on the projector CD for information on
adding passwords.
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2010 Epson America, Inc. 8/10
Printed in XXXXXX
CPD-28070