Epson PowerLite 825 Multimedia Projector Quick Setup Guide

PowerLite® 85/825/826W
Quick Setup
Microphone
Connect a dynamic microphone to the Mic port, using a 3.5 mm mini-jack cable.
Turn on your equipment
1
2
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
3
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
Turn on your computer or video source.
Plug in the projector.
Focus
Connect the projector
Zoom
Choose from the following connections:
Computer Monitor Port
3
Connect a computer using the VGA cable that came with the projector.
Video Player
Open the A/V Mute slide all the way.
Connect up to 4 video devices and use the remote control to switch between
them.
Component video S-Video
RCA video cable
cable
to VGA cable
(composite video)
(optional)
(optional)
(optional)
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Using the remote control
Audio cable
(optional)
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Power light
Connect one end to the projector’s Computer1 or Computer2 port, and
the other end to your computer’s
monitor port. If you are using a
notebook, switch it to external display. You can also connect an audio cable or
microphone.
Power button
Computer USB Port
Connect a computer (Windows® 2000 or later only) using the USB cable that
came with the projector.
Connect the square end of the USB cable to the projector’s
Type B
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. You can also connect an audio cable or microphone.
The
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Connect a digital camera, document camera, or other USB device to the
projector’s
Type A (flat) USB port.
Digital camera
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the Search button on the remote control to select the image
source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the blue foot release button and lift the front of
the projector. Release the button to lock the foot in position.
Thumb drive
Follow the on-screen instructions to install the Epson USB Display software.
Then press the USB button on the remote control.
DC-06 document camera
Connect the projector to your network using an Ethernet cable. See “Project
Over the Network” on the back of this sheet for more information.
®
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature. See the EasyMP Operation Guide on your
projector CD.
For information on playing sound through the projector or connecting an
external monitor, see the User’s Guide on your projector CD.
*411676200*
*411676200*
Turn projector
on and off
Choose which
source to display
Turn off projector
display and sound
Camera or USB Device
Network (LAN)
power light flashes green, then stays on.
Change
presentation
slides (USB
connection only)
Control projector volume
Navigate
projector
menus
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see your User’s Guide.
PowerLite® 85/825/826W
Quick Setup
Microphone
Connect a dynamic microphone to the Mic port, using a 3.5 mm mini-jack cable.
Turn on your equipment
1
2
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
3
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
Turn on your computer or video source.
Plug in the projector.
Focus
Connect the projector
Zoom
Choose from the following connections:
Computer Monitor Port
3
Connect a computer using the VGA cable that came with the projector.
Video Player
Open the A/V Mute slide all the way.
Connect up to 4 video devices and use the remote control to switch between
them.
Component video S-Video
RCA video cable
cable
to VGA cable
(composite video)
(optional)
(optional)
(optional)
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Using the remote control
Audio cable
(optional)
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Power light
Connect one end to the projector’s Computer1 or Computer2 port, and
the other end to your computer’s
monitor port. If you are using a
notebook, switch it to external display. You can also connect an audio cable or
microphone.
Power button
Computer USB Port
Connect a computer (Windows® 2000 or later only) using the USB cable that
came with the projector.
Connect the square end of the USB cable to the projector’s
Type B
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. You can also connect an audio cable or microphone.
The
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Connect a digital camera, document camera, or other USB device to the
projector’s
Type A (flat) USB port.
Digital camera
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the Search button on the remote control to select the image
source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the blue foot release button and lift the front of
the projector. Release the button to lock the foot in position.
Thumb drive
Follow the on-screen instructions to install the Epson USB Display software.
Then press the USB button on the remote control.
DC-06 document camera
Connect the projector to your network using an Ethernet cable. See “Project
Over the Network” on the back of this sheet for more information.
®
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature. See the EasyMP Operation Guide on your
projector CD.
For information on playing sound through the projector or connecting an
external monitor, see the User’s Guide on your projector CD.
*411676200*
*411676200*
Turn projector
on and off
Choose which
source to display
Turn off projector
display and sound
Camera or USB Device
Network (LAN)
power light flashes green, then stays on.
Change
presentation
slides (USB
connection only)
Control projector volume
Navigate
projector
menus
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see your User’s Guide.
PowerLite® 85/825/826W
Quick Setup
Microphone
Connect a dynamic microphone to the Mic port, using a 3.5 mm mini-jack cable.
Turn on your equipment
1
2
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
3
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
Turn on your computer or video source.
Plug in the projector.
Focus
Connect the projector
Zoom
Choose from the following connections:
Computer Monitor Port
3
Connect a computer using the VGA cable that came with the projector.
Video Player
Open the A/V Mute slide all the way.
Connect up to 4 video devices and use the remote control to switch between
them.
Component video S-Video
RCA video cable
cable
to VGA cable
(composite video)
(optional)
(optional)
(optional)
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Using the remote control
Audio cable
(optional)
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Power light
Connect one end to the projector’s Computer1 or Computer2 port, and
the other end to your computer’s
monitor port. If you are using a
notebook, switch it to external display. You can also connect an audio cable or
microphone.
Power button
Computer USB Port
Connect a computer (Windows® 2000 or later only) using the USB cable that
came with the projector.
Connect the square end of the USB cable to the projector’s
Type B
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. You can also connect an audio cable or microphone.
The
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Connect a digital camera, document camera, or other USB device to the
projector’s
Type A (flat) USB port.
Digital camera
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the Search button on the remote control to select the image
source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the blue foot release button and lift the front of
the projector. Release the button to lock the foot in position.
Thumb drive
Follow the on-screen instructions to install the Epson USB Display software.
Then press the USB button on the remote control.
DC-06 document camera
Connect the projector to your network using an Ethernet cable. See “Project
Over the Network” on the back of this sheet for more information.
®
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature. See the EasyMP Operation Guide on your
projector CD.
For information on playing sound through the projector or connecting an
external monitor, see the User’s Guide on your projector CD.
*411676200*
*411676200*
Turn projector
on and off
Choose which
source to display
Turn off projector
display and sound
Camera or USB Device
Network (LAN)
power light flashes green, then stays on.
Change
presentation
slides (USB
connection only)
Control projector volume
Navigate
projector
menus
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see your User’s Guide.
PowerLite® 85/825/826W
Quick Setup
Microphone
Connect a dynamic microphone to the Mic port, using a 3.5 mm mini-jack cable.
Turn on your equipment
1
2
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
3
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
Turn on your computer or video source.
Plug in the projector.
Focus
Connect the projector
Zoom
Choose from the following connections:
Computer Monitor Port
3
Connect a computer using the VGA cable that came with the projector.
Video Player
Open the A/V Mute slide all the way.
Connect up to 4 video devices and use the remote control to switch between
them.
Component video S-Video
RCA video cable
cable
to VGA cable
(composite video)
(optional)
(optional)
(optional)
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Using the remote control
Audio cable
(optional)
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Power light
Connect one end to the projector’s Computer1 or Computer2 port, and
the other end to your computer’s
monitor port. If you are using a
notebook, switch it to external display. You can also connect an audio cable or
microphone.
Power button
Computer USB Port
Connect a computer (Windows® 2000 or later only) using the USB cable that
came with the projector.
Connect the square end of the USB cable to the projector’s
Type B
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. You can also connect an audio cable or microphone.
The
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Connect a digital camera, document camera, or other USB device to the
projector’s
Type A (flat) USB port.
Digital camera
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the Search button on the remote control to select the image
source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the blue foot release button and lift the front of
the projector. Release the button to lock the foot in position.
Thumb drive
Follow the on-screen instructions to install the Epson USB Display software.
Then press the USB button on the remote control.
DC-06 document camera
Connect the projector to your network using an Ethernet cable. See “Project
Over the Network” on the back of this sheet for more information.
®
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature. See the EasyMP Operation Guide on your
projector CD.
For information on playing sound through the projector or connecting an
external monitor, see the User’s Guide on your projector CD.
*411676200*
*411676200*
Turn projector
on and off
Choose which
source to display
Turn off projector
display and sound
Camera or USB Device
Network (LAN)
power light flashes green, then stays on.
Change
presentation
slides (USB
connection only)
Control projector volume
Navigate
projector
menus
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see your User’s Guide.
Project over the network
Network configuration
Troubleshooting
Where to get help
Install EMP NS Connection on each computer that will project over the
network. Use the CD labeled Epson Projector Software for Meeting &
Monitoring to install EMP NS Connection. If you need to configure the
projector for your network, see “Network Configuration.”
If you need to configure the projector for your network, you can use the
projector’s menu system.
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer, check the following:
For more information about using the projector, install the manuals from your
projector CD.
•
Telephone Support Services
1
1
Press the Menu button on the remote control, select the Network menu,
then press Enter.
Press the LAN button on the remote control.
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
Press the Source Search button on the projector or the Search button
on the remote control to select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
2
Start EMP NS Connection on your computer.
Windows: Select Start > Programs or All Programs > EPSON
Projector > EMP NS Connection.
Mac OS® X: Double-click the EMP NS Connection icon in your
Applications folder.
3
Select Advanced Connection Mode and click OK.
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
2
3
4
Choose Network Configuration and press Enter.
Select the Wired LAN menu and press Enter.
Choose IP Settings and press Enter. You see a screen like the following:
Windows
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
2
Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button.
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless LAN module, you can project
wirelessly. To purchase the Wireless LAN module or other accessories,
see “Optional Accessories.” For more information about using the
projector on a network, see your User’s Guide and EasyMP Operation
Guide.
5
•
6
7
8
From the Windows Control Panel, open the Display utility. In Windows
Vista®, right-click on the desktop and select Personalize, then select
Display Settings.
Click Settings, then click Advanced. In Windows Vista, click Advanced
Settings.
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson with
your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the registration card or CD included with your projector, or
register online at www.epson.com/webreg.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
If your network assigns addresses automatically, turn on the DHCP
setting.
If your network does not assign addresses automatically, turn
off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the
buttons on the remote control to
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, highlight
Return, then press the Enter button.
To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
Internet Support
Optional accessories
Do one of the following:
•
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
1
4
U.S.:
If the projector and notebook don’t display the same
image...
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday,
for the duration of your warranty period. You may also speak with a projector
support specialist by dialing one of these numbers:
3
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external Monitor port is set as your
primary display and/or enabled.
When you’re done making all necessary changes, select Complete and
press the Enter button to save your settings. Then press Enter again to
confirm.
Mac OS® X
Press the Menu button to exit the menu system.
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Product
Part number
Replacement lamp V13H010L50
Air filter replacement set (2 filters)
V13H134A22
Image presentation camera (ELPDC05)
V12H162020
DC-10s document camera
ELPDC10S
DC-06 document camera
V12H321001
Wireless LAN module
V12H306P11
Quick Wireless Connection USB key
V12H005M05
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 2/09
Printed in XXXXXX
CPD-27443
Project over the network
Network configuration
Troubleshooting
Where to get help
Install EMP NS Connection on each computer that will project over the
network. Use the CD labeled Epson Projector Software for Meeting &
Monitoring to install EMP NS Connection. If you need to configure the
projector for your network, see “Network Configuration.”
If you need to configure the projector for your network, you can use the
projector’s menu system.
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer, check the following:
For more information about using the projector, install the manuals from your
projector CD.
•
Telephone Support Services
1
1
Press the Menu button on the remote control, select the Network menu,
then press Enter.
Press the LAN button on the remote control.
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
Press the Source Search button on the projector or the Search button
on the remote control to select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
2
Start EMP NS Connection on your computer.
Windows: Select Start > Programs or All Programs > EPSON
Projector > EMP NS Connection.
Mac OS® X: Double-click the EMP NS Connection icon in your
Applications folder.
3
Select Advanced Connection Mode and click OK.
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
2
3
4
Choose Network Configuration and press Enter.
Select the Wired LAN menu and press Enter.
Choose IP Settings and press Enter. You see a screen like the following:
Windows
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
2
Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button.
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless LAN module, you can project
wirelessly. To purchase the Wireless LAN module or other accessories,
see “Optional Accessories.” For more information about using the
projector on a network, see your User’s Guide and EasyMP Operation
Guide.
5
•
6
7
8
From the Windows Control Panel, open the Display utility. In Windows
Vista®, right-click on the desktop and select Personalize, then select
Display Settings.
Click Settings, then click Advanced. In Windows Vista, click Advanced
Settings.
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson with
your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the registration card or CD included with your projector, or
register online at www.epson.com/webreg.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
If your network assigns addresses automatically, turn on the DHCP
setting.
If your network does not assign addresses automatically, turn
off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the
buttons on the remote control to
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, highlight
Return, then press the Enter button.
To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
Internet Support
Optional accessories
Do one of the following:
•
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
1
4
U.S.:
If the projector and notebook don’t display the same
image...
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday,
for the duration of your warranty period. You may also speak with a projector
support specialist by dialing one of these numbers:
3
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external Monitor port is set as your
primary display and/or enabled.
When you’re done making all necessary changes, select Complete and
press the Enter button to save your settings. Then press Enter again to
confirm.
Mac OS® X
Press the Menu button to exit the menu system.
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Product
Part number
Replacement lamp V13H010L50
Air filter replacement set (2 filters)
V13H134A22
Image presentation camera (ELPDC05)
V12H162020
DC-10s document camera
ELPDC10S
DC-06 document camera
V12H321001
Wireless LAN module
V12H306P11
Quick Wireless Connection USB key
V12H005M05
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 2/09
Printed in XXXXXX
CPD-27443
Project over the network
Network configuration
Troubleshooting
Where to get help
Install EMP NS Connection on each computer that will project over the
network. Use the CD labeled Epson Projector Software for Meeting &
Monitoring to install EMP NS Connection. If you need to configure the
projector for your network, see “Network Configuration.”
If you need to configure the projector for your network, you can use the
projector’s menu system.
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer, check the following:
For more information about using the projector, install the manuals from your
projector CD.
•
Telephone Support Services
1
1
Press the Menu button on the remote control, select the Network menu,
then press Enter.
Press the LAN button on the remote control.
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
Press the Source Search button on the projector or the Search button
on the remote control to select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
2
Start EMP NS Connection on your computer.
Windows: Select Start > Programs or All Programs > EPSON
Projector > EMP NS Connection.
Mac OS® X: Double-click the EMP NS Connection icon in your
Applications folder.
3
Select Advanced Connection Mode and click OK.
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
2
3
4
Choose Network Configuration and press Enter.
Select the Wired LAN menu and press Enter.
Choose IP Settings and press Enter. You see a screen like the following:
Windows
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
2
Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button.
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless LAN module, you can project
wirelessly. To purchase the Wireless LAN module or other accessories,
see “Optional Accessories.” For more information about using the
projector on a network, see your User’s Guide and EasyMP Operation
Guide.
5
•
6
7
8
From the Windows Control Panel, open the Display utility. In Windows
Vista®, right-click on the desktop and select Personalize, then select
Display Settings.
Click Settings, then click Advanced. In Windows Vista, click Advanced
Settings.
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson with
your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the registration card or CD included with your projector, or
register online at www.epson.com/webreg.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
If your network assigns addresses automatically, turn on the DHCP
setting.
If your network does not assign addresses automatically, turn
off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the
buttons on the remote control to
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, highlight
Return, then press the Enter button.
To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
Internet Support
Optional accessories
Do one of the following:
•
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
1
4
U.S.:
If the projector and notebook don’t display the same
image...
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday,
for the duration of your warranty period. You may also speak with a projector
support specialist by dialing one of these numbers:
3
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external Monitor port is set as your
primary display and/or enabled.
When you’re done making all necessary changes, select Complete and
press the Enter button to save your settings. Then press Enter again to
confirm.
Mac OS® X
Press the Menu button to exit the menu system.
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Product
Part number
Replacement lamp V13H010L50
Air filter replacement set (2 filters)
V13H134A22
Image presentation camera (ELPDC05)
V12H162020
DC-10s document camera
ELPDC10S
DC-06 document camera
V12H321001
Wireless LAN module
V12H306P11
Quick Wireless Connection USB key
V12H005M05
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 2/09
Printed in XXXXXX
CPD-27443
Project over the network
Network configuration
Troubleshooting
Where to get help
Install EMP NS Connection on each computer that will project over the
network. Use the CD labeled Epson Projector Software for Meeting &
Monitoring to install EMP NS Connection. If you need to configure the
projector for your network, see “Network Configuration.”
If you need to configure the projector for your network, you can use the
projector’s menu system.
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer, check the following:
For more information about using the projector, install the manuals from your
projector CD.
•
Telephone Support Services
1
1
Press the Menu button on the remote control, select the Network menu,
then press Enter.
Press the LAN button on the remote control.
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
Press the Source Search button on the projector or the Search button
on the remote control to select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
2
Start EMP NS Connection on your computer.
Windows: Select Start > Programs or All Programs > EPSON
Projector > EMP NS Connection.
Mac OS® X: Double-click the EMP NS Connection icon in your
Applications folder.
3
Select Advanced Connection Mode and click OK.
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
2
3
4
Choose Network Configuration and press Enter.
Select the Wired LAN menu and press Enter.
Choose IP Settings and press Enter. You see a screen like the following:
Windows
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
2
Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button.
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless LAN module, you can project
wirelessly. To purchase the Wireless LAN module or other accessories,
see “Optional Accessories.” For more information about using the
projector on a network, see your User’s Guide and EasyMP Operation
Guide.
5
•
6
7
8
From the Windows Control Panel, open the Display utility. In Windows
Vista®, right-click on the desktop and select Personalize, then select
Display Settings.
Click Settings, then click Advanced. In Windows Vista, click Advanced
Settings.
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson with
your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the registration card or CD included with your projector, or
register online at www.epson.com/webreg.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
If your network assigns addresses automatically, turn on the DHCP
setting.
If your network does not assign addresses automatically, turn
off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the
buttons on the remote control to
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, highlight
Return, then press the Enter button.
To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
Internet Support
Optional accessories
Do one of the following:
•
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
1
4
U.S.:
If the projector and notebook don’t display the same
image...
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday,
for the duration of your warranty period. You may also speak with a projector
support specialist by dialing one of these numbers:
3
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external Monitor port is set as your
primary display and/or enabled.
When you’re done making all necessary changes, select Complete and
press the Enter button to save your settings. Then press Enter again to
confirm.
Mac OS® X
Press the Menu button to exit the menu system.
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Product
Part number
Replacement lamp V13H010L50
Air filter replacement set (2 filters)
V13H134A22
Image presentation camera (ELPDC05)
V12H162020
DC-10s document camera
ELPDC10S
DC-06 document camera
V12H321001
Wireless LAN module
V12H306P11
Quick Wireless Connection USB key
V12H005M05
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 2/09
Printed in XXXXXX
CPD-27443