PowerLite Home Cinema 5030UB/5030UBe
PowerLite Pro Cinema 4030/6030UB
®
®
Quick Setup
2
Turn on your equipment
Plug the AC adapter into the transmitter and a wall outlet.
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
1
Turn on your video source.
2
Plug in the projector.
5Turn the focus ring to sharpen the image.
Choose a location
Keep the projector level and place it at a height so its lens is even with the
top or bottom of the screen and is centered horizontally. If this isn’t possible,
use the lens shift dials or the keystone correction buttons on the projector to
reposition the image (see “Adjust the image”).
3Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the WirelessHD Transmitter. You can connect up
to five input devices to the transmitter. See “Viewing WirelessHD content”
for information on switching between input sources
but if necessary you can press the
correct this.
4To use the transmitter as a pass-through device to a television or other
power button on the
projector or the Standby button on the remote control twice, then
unplug it. You don’t have to wait for the projector to cool down.
4The default language of the menu system is English. To select another
language, press the Menu button on the projector or remote control.
Select Extended and press Enter. Select Language and press Enter.
Select your language and press Enter. Press the Menu button to exit
the menu system.
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” for
information on switching between wireless and wired display modes.
Adjust the image
Choose from the following connections. For additional connection types, see
the online User’s Guide.
1If you don’t see an image, press one of the Source buttons on the remote
HDMI cable
control or the
Connect audio
Note: When setting up the projector, make sure that it is placed level
to the screen in order to provide the best possible image quality. If you
must set up the projector at an angle, use the or buttons to correct
the image shape.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
button on the projector to select the image source.
Note: If you still see a blank screen or have other display problems,
see “Troubleshooting.”
Connect your device’s audio output to your home theater receiver or powered
speakers.
2Turn the horizontal and vertical lens shift dials to adjust the image
position and center it on the screen.
Home theater system
RCA video cable
Turn projector on
Choose which source
to display
Video source
Component video cable
Turn projector off
Turn off projector
display
WirelessHD (PowerLite Home Cinema 5030UBe only)
3To raise the image, adjust the front feet as shown below.
Follow these steps to set up the included WirelessHD Transmitter.
Video cable
Surround sound
Receiver
Navigate projector
menus
Access projector
menus
4
Video cable
External speakers
front of the transmitter faces the front of the projector. See the online
User’s Guide for more information on the WirelessHD transmission range.
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
Switch between
2D and 3D
Projector
Powered speakers
1Place the transmitter within 32 feet (10 m) of the projector. Make sure the
,
Note: To shut down the projector, press the
Connect the projector
Connect up to 4 video devices and use the Source buttons on the remote
control or the
button on the projector to switch between them.
or
buttons on the projector to
power button on the projector or the On button on the
remote control. The shutter opens and the power light flashes blue,
then stays on.
Note: You can connect tablets, smartphones and other devices that
support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Devices that use MHL connection include the
Samsung™ Galaxy Note II™ and the Roku® Streaming Stick™. Some
devices may require an adapter or may not require an MHL cable.
Not all features or functions may be supported. Check your device’s
documentation for more information.
Video device
or
3Press the
In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
See the online User’s Guide for more information on where to place your
projector.
6Your projector automatically adjusts images that look like
Video source
Turn the zoom ring to reduce or enlarge the image.
Control WirelessHD
functions
Projector
Note: See your home theater receiver documentation for more information
on connections.
For more information on using the remote control, see the online
User’s Guide.
PowerLite Home Cinema 5030UB/5030UBe
PowerLite Pro Cinema 4030/6030UB
®
®
Quick Setup
2
Turn on your equipment
Plug the AC adapter into the transmitter and a wall outlet.
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
1
Turn on your video source.
2
Plug in the projector.
5Turn the focus ring to sharpen the image.
Choose a location
Keep the projector level and place it at a height so its lens is even with the
top or bottom of the screen and is centered horizontally. If this isn’t possible,
use the lens shift dials or the keystone correction buttons on the projector to
reposition the image (see “Adjust the image”).
3Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the WirelessHD Transmitter. You can connect up
to five input devices to the transmitter. See “Viewing WirelessHD content”
for information on switching between input sources
but if necessary you can press the
correct this.
4To use the transmitter as a pass-through device to a television or other
power button on the
projector or the Standby button on the remote control twice, then
unplug it. You don’t have to wait for the projector to cool down.
4The default language of the menu system is English. To select another
language, press the Menu button on the projector or remote control.
Select Extended and press Enter. Select Language and press Enter.
Select your language and press Enter. Press the Menu button to exit
the menu system.
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” for
information on switching between wireless and wired display modes.
Adjust the image
Choose from the following connections. For additional connection types, see
the online User’s Guide.
1If you don’t see an image, press one of the Source buttons on the remote
HDMI cable
control or the
Connect audio
Note: When setting up the projector, make sure that it is placed level
to the screen in order to provide the best possible image quality. If you
must set up the projector at an angle, use the or buttons to correct
the image shape.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
button on the projector to select the image source.
Note: If you still see a blank screen or have other display problems,
see “Troubleshooting.”
Connect your device’s audio output to your home theater receiver or powered
speakers.
2Turn the horizontal and vertical lens shift dials to adjust the image
position and center it on the screen.
Home theater system
RCA video cable
Turn projector on
Choose which source
to display
Video source
Component video cable
Turn projector off
Turn off projector
display
WirelessHD (PowerLite Home Cinema 5030UBe only)
3To raise the image, adjust the front feet as shown below.
Follow these steps to set up the included WirelessHD Transmitter.
Video cable
Surround sound
Receiver
Navigate projector
menus
Access projector
menus
4
Video cable
External speakers
front of the transmitter faces the front of the projector. See the online
User’s Guide for more information on the WirelessHD transmission range.
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
Switch between
2D and 3D
Projector
Powered speakers
1Place the transmitter within 32 feet (10 m) of the projector. Make sure the
,
Note: To shut down the projector, press the
Connect the projector
Connect up to 4 video devices and use the Source buttons on the remote
control or the
button on the projector to switch between them.
or
buttons on the projector to
power button on the projector or the On button on the
remote control. The shutter opens and the power light flashes blue,
then stays on.
Note: You can connect tablets, smartphones and other devices that
support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Devices that use MHL connection include the
Samsung™ Galaxy Note II™ and the Roku® Streaming Stick™. Some
devices may require an adapter or may not require an MHL cable.
Not all features or functions may be supported. Check your device’s
documentation for more information.
Video device
or
3Press the
In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
See the online User’s Guide for more information on where to place your
projector.
6Your projector automatically adjusts images that look like
Video source
Turn the zoom ring to reduce or enlarge the image.
Control WirelessHD
functions
Projector
Note: See your home theater receiver documentation for more information
on connections.
For more information on using the remote control, see the online
User’s Guide.
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector.
1
Turn on and begin playback on the 3D-compatible video device.
Note: Make sure you set the video device to play content in 3D mode.
2
Press the 2D/3D button on the remote control, if necessary.
5Press the WirelessHD button on the remote control.
Note: If the WirelessHD connection fails, press the Setup button on
the bottom of the transmitter, then try again.
Where to get help
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Manual
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
6If you have connected multiple input devices to the transmitter, press
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t have
a User’s Guide icon, you can install it from the projector CD or go to the Epson
website, as described below.
7
Telephone support services
the Input button on the remote control or transmitter once to display
the sub-screen menu, then press the button again to switch between the
input devices.
To display two WirelessHD input devices simultaneously, press the P-in-P
button on the remote control to enable picture-in-picture mode. Press
and hold the P-in-P button for three seconds to switch the main image
and sub-screen, or press the P-in-P button again to disable picture-inpicture mode.
To use the Epson® PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with a
support specialist by calling (562) 276-4394 (US) or (905) 709-3839 (Canada).
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection and display modes.
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change
without notice. Toll or long distance charges may apply.
3Slide the power switch on your 3D glasses to the On position.
Properly shielded cables must be used for connections to LCD Projector in
order to meet FCC emission limits. The cable for peripheral with a ferrite core
must be used for RF interference suppression.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Canada
Industry Canada (IC) Notices
Contains IC: 1052D-E207, 6100A-AWWH064R
This Class B digital apparatus complies with Canadian ICES-003.
Troubleshooting
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
•Make sure the power light on the projector is blue and not flashing.
•
Press the
button on the projector or one of the Source buttons on
the remote control to switch to the correct image source, if necessary.
•
If you’re using a Windows® laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
You can also automatically convert 2D HDMI content to 3D. To enable the
2D-to-3D Conversion option, press the Menu button on the projector or
remote control. Select Signal and press Enter, then select 3D Setup and
press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak,
Medium, or Strong setting, then press Enter.
See the online User’s Guide for more information on adjusting 3D images.
Viewing WirelessHD
content (PowerLite Home
Cinema 5030UBe)
1
Turn on your video device and begin playback.
2Turn on the power switch on the side of the WirelessHD Transmitter.
3Turn on the projector.
4If you have connected a television or other display to the output port on
the transmitter and want to switch between wired and wireless display
modes, press the Output button on the remote control or transmitter.
The WiHD light on the transmitter will light up when the wireless display
mode is active.
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays checkbox.
If 3D images aren’t displaying properly, check the following:
•
Press the 2D/3D button to switch to 3D viewing mode, if necessary.
•
Make sure that you are within the 3D viewing range. See “Choose a
location” on the front of this sheet or the online User’s Guide for more
information.
•
•
•
Check that your 3D glasses have not entered standby mode. Slide the
power switch on the 3D glasses into the Off position, then back to the
On position.
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option
is selected.
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
If WirelessHD content isn’t displaying properly, check the following:
•
Check that the Link light on the transmitter is lit. If the light is flashing
slowly, the transmitter could not connect with the projector and has
entered standby mode. Verify that the projector is turned on and
that all cables are properly connected as shown in the “Connect the
projector” section.
•
Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the
projector, isn’t obstructed by any large objects and is not placed on a
metal surface.
•
If you are viewing wireless content, make sure that the WiHD light on
the transmitter is lit. If it isn’t, press the Output button on the remote
control or transmitter.
Internet support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates and exclusive offers. You can use the CD
included with your projector or register online at www.epson.com/webreg.
Optional accessories
CAN ICES-3(B)/NMB-3(B)
This device complies with RSS-210 of the Industry Canada Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses (part number V12H548006) or other
accessories from an Epson authorized reseller. To find the nearest reseller,
call 800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Notices
Bluetooth Safety and Specifications
Contains Bluetooth module model: DBUB-E207
This document provides safety instructions and describes the specifications.
Read this document carefully before use to ensure your safety and product
performance.
U.S.
FCC Notices
Contains FCC ID: BKMAE-E207, TLZ-WH064R
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
•
Consult the dealer or an experienced radio/TV technician for help.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2013 Epson America, Inc., 6/13
Printed in XXXXXX
CPD-39803
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector.
1
Turn on and begin playback on the 3D-compatible video device.
Note: Make sure you set the video device to play content in 3D mode.
2
Press the 2D/3D button on the remote control, if necessary.
5Press the WirelessHD button on the remote control.
Note: If the WirelessHD connection fails, press the Setup button on
the bottom of the transmitter, then try again.
Where to get help
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Manual
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
6If you have connected multiple input devices to the transmitter, press
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t have
a User’s Guide icon, you can install it from the projector CD or go to the Epson
website, as described below.
7
Telephone support services
the Input button on the remote control or transmitter once to display
the sub-screen menu, then press the button again to switch between the
input devices.
To display two WirelessHD input devices simultaneously, press the P-in-P
button on the remote control to enable picture-in-picture mode. Press
and hold the P-in-P button for three seconds to switch the main image
and sub-screen, or press the P-in-P button again to disable picture-inpicture mode.
To use the Epson® PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with a
support specialist by calling (562) 276-4394 (US) or (905) 709-3839 (Canada).
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection and display modes.
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change
without notice. Toll or long distance charges may apply.
3Slide the power switch on your 3D glasses to the On position.
Properly shielded cables must be used for connections to LCD Projector in
order to meet FCC emission limits. The cable for peripheral with a ferrite core
must be used for RF interference suppression.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Canada
Industry Canada (IC) Notices
Contains IC: 1052D-E207, 6100A-AWWH064R
This Class B digital apparatus complies with Canadian ICES-003.
Troubleshooting
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
•Make sure the power light on the projector is blue and not flashing.
•
Press the
button on the projector or one of the Source buttons on
the remote control to switch to the correct image source, if necessary.
•
If you’re using a Windows® laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
You can also automatically convert 2D HDMI content to 3D. To enable the
2D-to-3D Conversion option, press the Menu button on the projector or
remote control. Select Signal and press Enter, then select 3D Setup and
press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak,
Medium, or Strong setting, then press Enter.
See the online User’s Guide for more information on adjusting 3D images.
Viewing WirelessHD
content (PowerLite Home
Cinema 5030UBe)
1
Turn on your video device and begin playback.
2Turn on the power switch on the side of the WirelessHD Transmitter.
3Turn on the projector.
4If you have connected a television or other display to the output port on
the transmitter and want to switch between wired and wireless display
modes, press the Output button on the remote control or transmitter.
The WiHD light on the transmitter will light up when the wireless display
mode is active.
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays checkbox.
If 3D images aren’t displaying properly, check the following:
•
Press the 2D/3D button to switch to 3D viewing mode, if necessary.
•
Make sure that you are within the 3D viewing range. See “Choose a
location” on the front of this sheet or the online User’s Guide for more
information.
•
•
•
Check that your 3D glasses have not entered standby mode. Slide the
power switch on the 3D glasses into the Off position, then back to the
On position.
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option
is selected.
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
If WirelessHD content isn’t displaying properly, check the following:
•
Check that the Link light on the transmitter is lit. If the light is flashing
slowly, the transmitter could not connect with the projector and has
entered standby mode. Verify that the projector is turned on and
that all cables are properly connected as shown in the “Connect the
projector” section.
•
Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the
projector, isn’t obstructed by any large objects and is not placed on a
metal surface.
•
If you are viewing wireless content, make sure that the WiHD light on
the transmitter is lit. If it isn’t, press the Output button on the remote
control or transmitter.
Internet support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates and exclusive offers. You can use the CD
included with your projector or register online at www.epson.com/webreg.
Optional accessories
CAN ICES-3(B)/NMB-3(B)
This device complies with RSS-210 of the Industry Canada Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses (part number V12H548006) or other
accessories from an Epson authorized reseller. To find the nearest reseller,
call 800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Notices
Bluetooth Safety and Specifications
Contains Bluetooth module model: DBUB-E207
This document provides safety instructions and describes the specifications.
Read this document carefully before use to ensure your safety and product
performance.
U.S.
FCC Notices
Contains FCC ID: BKMAE-E207, TLZ-WH064R
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
•
Consult the dealer or an experienced radio/TV technician for help.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2013 Epson America, Inc., 6/13
Printed in XXXXXX
CPD-39803