Euro-Pro BIG EP134 Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS
When using your EURO-PRO BIG SHARK, basic safety precautions should
always be observed, including the following:
1.
2.
3.
OWNER’S MANUAL
Model EP134
115V~, 60Hz., 7.8 Amps
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Read all instructions before using your
BIG SHARK hand vacuum.
Use the system only for its intended use.
To protect against a risk of electric shock,
do not immerse any part of the system in
water or other liquids.
Never yank cord to disconnect from
outlet; instead, grasp plug and pull to
disconnect.
Do not allow cord to touch hot surfaces.
Do not run appliance over cord.
Do not operate the system with a damaged
cord or plug, or if the appliance or any other
part of the system has been dropped or
damaged. To avoid the risk of electric
shock, do not disassemble or attempt to
repair the BIG SHARK. Return the
system to EURO-PRO Corporation (see
warranty) for examination and repair.
Incorrect re-assembly or repair can cause a
risk of electrical shock or injury to persons
when the BIG SHARK is used.
Close supervision is necessary for any
appliance being used by or near children.
Do not leave the system unattended while
connected.
Keep hair, loose clothing, fingers and all
parts of body away from opening and
moving parts.
Do not use to pick up flammable or
combustible liquids such as gasoline or use
in areas where they may be present.
Do not pick up anything that is burning or
smoking such as cigarettes, matches or hot
ashes.
Use extra care when cleaning on stairs.
Do not use the hand vacuum without the
dust cup filter in place.
This appliance is intended only for
household use. Follow all user instructions
in this manual.
To reduce the risk of fire, electric shock, or
injury:
• Do not leave the BIG SHARK plugged in
when unattended. Unplug the electrical cord
when not in use and before servicing.
• Do not allow to be used as a toy. Close
attention is necessary when used by or near
children, pets or plants.
• Use only as described in this manual. Use
only manufacturer’s recommended
accessories.
• Do not pull cord, use cord as a handle, close
a door on cord, or pull cord around sharp
edges or corners. Keep cord away from
heated surfaces.
• Use only extension cords UL-rated or cUL at
15 amperes. extension cords rated for less
amperage may overheat. Care should be
taken to arrange the cord so that the cord
cannot be pulled or tripped over.
• Turn off all controls as applicable before
unplugging from electrical outlet.
• Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
• Do not handle plug or hand vacuum with wet
hands or operate without shoes.
• Do not put any objects into openings. Do not
use with any opening blocked. Keep free of
dust, lint, hair and anything else that may
reduce air flow.
• Store your appliance indoors in a cool, dry
area.
• Keep your work area well lit.
• Do not immerse the hand vacuum into water
or other liquids.
• Keep end of hose, wands and other openings
away from your face and body.
• Use only on dry surfaces.
• Using improper voltage may result in damage
to the motor and possible injury to the user.
Correct voltage is listed on rating label.
SAVE THESE INSTRUCTIONS
For Household Use Only
For information or assistance:
USA: EURO-PRO Corporation
178 West Service Rd.
Champlain, NY 12919
www.sharkhomecare.com
WARNING: To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
1
Rev. 06/02
OPERATING INSTRUCTIONS
GETTING TO KNOW YOUR BIG SHARK
Warning: Always unplug from
electrical outlet before opening the dust
cup (container).
Note: HEPA dust cup filter must be
used when operating the hand vacuum.
9
4. To use the flexible hose, push the
smaller end of the hose into the
suction hole, then attach the desired
accessory to the other end of the
flexible hose, as shown below.
Using The Unit As A Hand
Vacuum
1. To open the dust cup (container), push
button and pull out the dust cup. Verify
that the HEPA dust cup filter inside,
then attach the dust cup (container) to
the hand vacuum.
Debris Screen
11
How To Operate Your
Hand Vacuum
HEPA Filter
2. To use the Hand Vacuum with the
shoulder strap, attach it to the unit as
shown below.
1. Hold the hand vacuum firmly in
your hand by the Handle.
2. Push the On/Off Power Switch to
“On” position.
3. Start vacuuming.
CAUTION: The Hand Vacuum is a
very powerful unit. Make sure that you
hold it firmly, otherwise it can slip out of
your hand and cause injury.
12
8
7
3. To attach the crevice tool or oval
brush to the Hand Vacuum, push
brush into the suction hole, as
shown below.
10
1.
2.
3.
4.
5.
6.
7.
13
Push to Open Dust Cup (Container)
On/Off Power Switch
Suction Hole
Handle
Exhaust Cover Lock
Exhaust Cover
Shoulder Strap
8.
9.
10.
11.
12.
13.
Technical Specifications
Voltage:
Power:
115V~ 60Hz.
7.8 Amps, 900 Watts
2
Oval Brush
Holes for Attaching the Shoulder Strap
Dust Cup (Container)
Flexible Hose
Crevice Tool
Hepa Dust Cup Filter
Motor Thermostat
IMPORTANT: This motor is equipped with a motor protective thermostat.
If for some reason the vacuum cleaner should overheat,
the thermostat will automatically turn the unit OFF.
Should this occur, unplug the vacuum cleaner from wall
outlet or turn off switch. Allow the unit to cool. To restart,
re-plug into wall outlet or turn switch back on.
3
CLEANING & CHANGING THE POST MOTOR FILTER
OPERATING INSTRUCTIONS cont.
Cleaning & Changing the
HEPA Dust Cup Filter
Warning: Always unplug the unit from
Debris
Screen
electrical outlet before opening the Dust
Cup (container).
Important: Do NOT use the HEPA filter
cartridge without the debris screen in
place.
Fig. 3
5. Vigorously “TapClean”
the HEPA Dust Cup Fig. 4
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. (fig. 4)
Warning: After each Use - Always
remove the Filter Debris Screen from the
HEPA Dust Cup Filter, then vigorously
“TapClean” HEPA Filter until no more
dust can be removed.
IMPORTANT, Please Note : The
“TapClean” HEPA Dust Cup Filter &
Debris Screen will stop most of the tiniest
dust particles and airborne allergens from
re-entering the air you breathe. In fact it
stops 99.97% of all particles as small as
0.3 microns - many times smaller than a
human hair!!! Because of this incredible
filtration performance, the HEPA Dust Cup
Filter will quickly accumulate, inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. This can
cause the motor to overheat and the resettable thermostat to trip. (Should this
happen turn off the switch, unplug the unit
and allow unit to cool down. Clean the
HEPA Filter and Debris Screen as
described in this section, then reconnect
unit and proceed with vacuuming.)
6. “TapClean” the Debris
Screen or rinse under
a faucet until clean.
(fig. 5) Remember that
the Debris Screen
must be completely
dry before reinstalling
in the vacuum.
Fig.2
3. Empty the dust from the Dust Cup
(container).
4. Separate the debris screen from the
HEPA filter cartridge by grasping the
debris screen with one hand and the
filter frame with the other and pull
apart. (fig. 3)
1.
2.
3.
4.
5.
Fig. 5
Debris
Screen
PROBLEM
Put the filter into the grill-filter.
A severely solid or clogged filter
should be thoroughly washed
with fresh tepid water. A mild
detergent can be used if required.
HAND VACUUM
WILL NOT
OPERATE
POSSIBLE REASON
1.
2.
3.
4.
Power cord not firmly plugged
into outlet.
No power in wall outlet.
Needs servicing.
Thermostat has tripped.
POSSIBLE SOLUTION
1.
2.
3.
4.
1.
HAND VACUUM
WILL NOT PICK-UP
OR SUCTION
POWER IS WEAK
1.
2.
3.
Dust cup s full.
Unit clogged.
HEPA Dust Cup Filter needs
cleaning or replacing.
2.
3.
DUST ESCAPING
FROM HAND
VACUUM
HAND VACUUM
HOSE OR
BRUSHES WILL
NOT PICK-UP
1.
2.
3.
1.
2.
Dust cup is full.
HEPA Dust Cup Filter is not
installed correctly.
There is a puncture/hole in
HEPA Dust Cup Filter.
1.
2.
3.
1.
Hose clogged.
Dust cup is full.
2.
CAUTION: The suction hole must be
4
Push the Filter Cover Lock
to open the filter cover.
Remove the filter from the
grill-filter.
Rinse filter in lukewarm water
and dry the filter completely.
TROUBLE SHOOTING GUIDE
7. Replace the Debris Screen on the
HEPA Dust Cup Filter and reinstall
filter assembly in the vacuum. (not
shown)
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
is properly
"TapCleaned”
after each use
Fig. A
and suction
Wash only
once every
does not return
three (3)
to 100%, then
months.
we suggest that
Warning: Allow 24
the HEPA filter
hours for drying before
be “TapCleaned”
replacing in unit.
vigorously until no
more dust can be removed, then
rinsed under the faucet and allowed to
dry for 24 hours before refitting into
the vacuum. (Fig. A) This should be
done not more frequently than
once every 3 months.
1. To open the Dust Cup (container),
push button and detach the Dust
Cup (container ). (Fig. 1)
2. Pull out the HEPA Dust Cup Filter
or cloth dust cup filter. (Fig. 2)
Fig. 1
HEPA Filter
1. Disconnect from electrical outlet
before cleaning the filter.
2. Filter should be cleaned at least twice
a year or when it becomes visible
solid.
3. Always operate the cleaner with the
filter installed.
4. Do not use a washing machine to
rinse the filter.
5. Do not use a hair dryer to dry it.
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
5
Plug unit in firmly.
Check fuse or breaker.
Replace fuse/reset breaker.
Call 1-800-798-7398.
Turn the unit off and unplug
from outlet.
Allow unit to cool down,
then Restart. Empty dust
cup – (see page 4).
Turn unit off and unplug
from wall outlet. Remove
HEPA Dust Cup Filter and
check for object(s) in air
duct and remove.
Clean or replace HEPA
Dust Cup Filter.
(see page 4)
Empty dust cup.
Review HEPA Dust Cup
Filter instructions.
(see page 4)
Replace HEPA dust cup
filter. (see page 4)
Remove hose and/or
bushes. Remove obstruction
from hose.
Empty and clean dust cup.
ORDERING REPLACEMENT DUST CUP FILTERS
TO ORDER REPLACEMENT FILTERS
for Model EP134
Call:
1-866-98SHARK (1-866-987-4275)
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
FOR TECHNICAL SUPPORT
for Model EP134
Call:
1-800-798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
or
visit our website: www.sharkhomecare.com
Please Note: The HEPA Dust Cup Filter may be washed. However, we
recommend that this NOT be done more frequently than once every three (3)
months.
To wash your HEPA Dust Cup Filter, hold filter cartridge by frame flange and rinse
under a tap until all observable dirt has been removed. Some discoloration of the
HEPA filter material may occur, this is normal and will not affect the filter’s
performance. When finished, shake off excess water. Do NOT wash in dishwasher.
It is important that when you wash the HEPA dust cup filter, you allow it to dry
COMPLETELY before using again. We recommend 24 hours to air dry. DO NOT
DRY IN DRYER.
Important: This motor is equipped with a motor protective thermostat. If for some
reason the vacuum cleaner should overheat, the thermostat will automatically turn
the unit off. Should this occur, unplug the vacuum cleaner from the wall outlet and
turn off switch. Allow the unit to cool. To restart, re-plug into wall outlet and turn
switch back on.
Model EP134
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO CORPORATION warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, return the complete appliance and accessories, freight prepaid to EURO-PRO
Corporation, 178 West Service Rd., Champlain, NY 12919. If the appliance is found by EURO-PRO to
be defective in material or workmanship, EURO-PRO will repair or replace it free of charge. Proof of
purchase date and $ 9.95 to cover the cost of return shipping and handling must be included. *
Non-durable parts including, without limitation, dust bags, filters, brushes and electrical parts which
normally require replacement are specifically excluded from warranty.
The liability of EURO-PRO Corporation is limited solely to the cost of the repair or replacement of the
unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit
that has been tampered with or used for commercial purposes. This limited warranty does not cover
damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or
mishandling in transit. This warranty does not cover damage or defects caused by or resulting from
damages from shipping or repairs, service or alterations to the product or any of its parts, which have
been performed by a repair person not authorized by EURO-PRO.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Corporation if any, is limited to the specific
obligations expressly assumed by it under the terms of the limited warranty. In no event is EUROPRO Corporation liable for incidental or consequential damages of any nature whatsoever. Some
states do not permit the exclusion or limitation of incidental or consequential damages, so the above
may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe is
the problem with item. We recommend you insure the package (as damage in shipping is not
covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”.
yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase in order to
validate the foregoing Limited Warranty. The registration will enable us to contact you in the unlikely
event of a product safety notification. By returning this card you acknowledge to have read and
understood the instructions for use, and warnings set forth in the accompanying instructions.
RETURN TO EURO-PRO CORPORATION: 178 West Service Rd., Champlain, NY 12919
Model EP134
________________________________________________________________________
Appliance model
________________________________________________________________________________
Date purchased
Name of store
________________________________________________________________________________
Owner’s name
________________________________________________________________________________
Address
City
State
Zip code
6
Printed in China