advertisement
IN70 Series
User's Guide
Please read the safety instructions booklet before setting up the projector.
1
Unpack the box
Here’s what’s included:
Projector Remote CD-ROM
1
2
Composite Video Cable Power Cord
M1-DA to HDMI
Adapter (IN78 only)
Put batteries in the remote
The remote uses 2 AA batteries.
2
+
-
+
3
Please dispose of batteries in an environmentally proper manner.
Remote illumination
Tap the button on the bottom of the remote for backlight, hold it down for flashlight*
*Illumination features may not be available on all models
3
Connect source
You can connect more than one source if needed.
Connection How-To Guides www.infocus.com/support/howto
Connect to:
DVD, Cable Box, VCR, or Game
Composite Video Cable (included) Stereo Audio Cable* (not included)
Basic
Video Out L R
Audio Out
DVD, Cable Box, VCR, or Game
L R
Audio In
Home Theater or Receiver
OR
*www.infocus.com/store part no. SP-RCAAUD-5M
Use optional cables (not included) for improved video quality
Connect to:
DVD, Cable Box, VCR, or Game
Use: S-Video Cable
Separates color from brightness to improve quality.
Good
To Audio In
S-Video Out
L R
Audio Out
DVD, Cable Box, VCR, or Game
www.infocus.com/store part no. SP-SVIDEO-
10
M
Better
To Audio In
Connect to:
HDTV Receiver or DVD
Use: Component Video Cable
Separates all color signals for better color accuracy. HDTV compatible.
www.infocus.com/store part no. SP-CPNT
Connect to:
HDTV Receiver
Use:
HDMI Cable
100% Digital connection.
HDTV compatible.
Video Out
Y Pb Pr
L R
Audio Out
HDTV Receiver or DVD
Best
To Audio In
HDMI Out
L R
Audio Out
HDTV Receiver
www.infocus.com/store part no. SP-HDMI
Connect to:
SCART Source
Use: SCART to RGBS Cable (RGB with sync)
1
Connect 4 color-coded connectors to corresponding connectors on projector.
2
Enable SCART RGB in the Source
Enable menu (Settings > Sources >
Source Enable).
Connect to:
DVI Source
Use:
M1 to DVI Cable
100% digital connection.
Connect the cable to the projector’s M1-DA/DVI connector. www.infocus.com/store part no. SP-DVI-D
4
Turn on projector and source
1
Connect the power cord to the projector and to an electrical outlet
The green light on the projector near the power button will turn on.
2
Turn on the projector
Press power (on the projector or remote). The green light on the projector will start blinking.
5-10 sec.
3
Wait for the lamp to warm up
After a few seconds, the green light will stop blinking and stay on. It can take a minute for the lamp to reach full brightness.
Warning:
Do not look directly into the lens when the projector is turned on.
4
Turn on the source device
Turn on your DVD player, cable box, VCR, game, or HDTV receiver.
5
Select the video source
If needed, press source (on the projector or remote) to view the source. You may have to press it more than once.
5
1
Height
Adjust the picture
Projector location
As distance increases, the image gets larger and moves upwards.
Tilt the projector up or down.
2
Keystone
Lens center line
4
5
To make the picture square:
1
2
Press menu (on projector or remote).
Press or to highlight Picture,
3
then press select.
Press or to highlight Keystone, then press select.
Press or to adjust keystone.
Press menu to exit.
3
Zoom and focus
zoom
(outer ring) focus
(inner ring)
Adjust zoom first, then focus the center of the image.
4
Aspect ratio
Interactive Screen Size and
Distance Calculator www.infocus.com/calculator
IN72
Diagonal
Screen Size
60” / 1.5 m
80” / 2 m
92” /2.3 m
150” / 3.8 m
Distance to Screen
Minimum Maximum
7’10” / 2.4 m
10’5” / 3.2 m
12’ / 3.7 m
19’6” / 5.9 m
9’4” / 2.8 m
12’4” / 3.8 m
14’2” / 4.3 m
23’1” / 7 m
IN74/IN76/IN78
Diagonal
Screen Size
60” / 1.5 m
80” / 2 m
92” /2.3 m
150” / 3.8 m
Distance to Screen
Minimum Maximum
6’7” / 2 m
8’10” / 2.7 m
10’1” / 3.1 m
16’5” / 5 m
8’4” / 2.5 m
11’1” / 3.4 m
12’10” / 3.9 m
20’10” / 6.3 m
Buy a Screen and Other Custom
Accessories www.infocus.com/store
Press resize (on the remote) to make the picture wider (16:9) or narrower (4:3).
6
Turn off the projector
Press the power button
The green light on the projector will blink while the fan cools the lamp. If you need to unplug the projector, wait until the fan stops and the green light stops blinking and stays on.
Note:
While the green light is blinking, button presses on the projector and remote are ignored.
7
Register with InFocus
It’s quick, easy, and secure.
Activate your warranty to ensure eligibility for service and support. Get special offers and notifications about free product updates.
1
Write down your projector’s serial number
It’s printed on the label on the back of the projector. You’ll need it to register (and if you ever need to contact InFocus support).
Serial number:
2
Go to
www.infocus.com/register
8
Read the Reference Guide and visit the InFocus web site
Insert the CD-ROM, or go to
www.infocus.com/support
The Reference Guide is on the CD-ROM in multiple languages. It covers advanced setup and operation, including lamp replacement instructions. The Reference Guide is also available at www.infocus.com/support
Troubleshooting
There is no picture or the image is blank
Check power
If the light on the projector near the power button is off, make sure the power cord is connected and plugged into a working electrical outlet.
If the light is green and not blinking, press the power button.
Check video source and cables
Make sure the video source (DVD player, cable box, VCR, game, HDTV receiver, etc.) is turned on and cables are securely connected between the source and the projector.
Press the Source button (on projector or remote)
You may need to press it several times to view the correct source.
Press the Auto Image button (on remote)
The picture is unstable or distorted, or “Signal out of range” is displayed
Press the Auto Image button (on remote)
The light on the projector is blinking red
Check air vents and lamp
Turn off the projector and remove anything that may be blocking its air vents. Leave the projector off for at least one minute to let it cool, then turn it on again. If the projector lamp won’t light and the red light starts to blink again, the lamp needs to be replaced.
For lamp replacement instructions, see the Reference Guide, which is on the included
CD-ROM or can be downloaded at www.infocus.com/support
More troubleshooting options are in the Reference Guide
The Reference Guide is on the included CD-ROM, or download it at www.infocus.com/support
Warning:
In the unlikely event of a lamp rupture, particles may be ejected from the projector.
Keep out of the area under and around the projector when it is turned on. See the safety instructions booklet for more details.
Questions? InFocus is here to help!
Visit us at: www.infocus.com/support
InFocus is here to support you with your new purchase. We can help you with…
• Determining screen sizes
• Documentation in other languages
• Connecting your sources (TV, DVD, Cable/Satellite, Game, etc.)
• Selecting optional accessories
• Product warranty protection plans
USA, Canada, Latin America
Customer Support Telephone
+1 (503) 685-8888
TOLL FREE: 800-799-9911
Mon-Fri, 7 am – 5 pm Pacific [email protected]
Asia Pacific
Customer Support Telephone
Singapore: +65 63539449
China: 800.828.2268
Australia: 1300-725-295
Australia Direct Sales: 1800-885-841
Mon-Fri, 9 am – 5 pm SGT [email protected]
Europe, Middle East, Africa
Customer Support Telephone
+31 (0)36 539 2820
Mon-Fri, 08:30 – 18:00 CET [email protected]
Warning: Hg - Lamp contains mercury. Manage in accordance with local disposal laws.
See www.lamprecycle.org
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070-8238 USA
European Office: Louis Amstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conforms to the following directives and norms: EMC Directive 89/336/EEC,
Amended by 93/68/EEC, EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3, Low Voltage Directive 73/23/EEC, Amended by
93/68/EEC, Safety: IEC 60950-1:1st Edition
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of
Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. InFocus, In Focus, and INFOCUS (stylized), LP, LiteShow, ScreenPlay, LitePort, ASK and Proxima are either registered trademarks or trademarks of InFocus
Corporation in the United States and other countries.
FCC Warning
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment that are not expressly approved by InFocus Corp. may void the user’s authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals Product Models: P720, P740, P760
UL, CUL, NOM, IRAM, GOST, C-tick
Other specific Country Approvals may apply. Please see product certification label.
InFocus reserves the right to alter product offerings and specifications at any time without notice.
Trident
IN72/IN74/IN76/IN78
Reference Guide
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conform to the following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: IEC 60950-1: 1 st
Edition
December, 2005
Trademarks
Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. Digital Light Processing is a trademark or registered trademark of
Texas Instruments. Pixelworks is a trademark or registered trademark of Pixelworks
Inc. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
InFocus, In Focus, and INFOCUS
(stylized), ASK and Proxima are either registered trademarks or trademarks of
InFocus Corporation in the United States and other countries.
FCC Warning
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, cUL, TUV, GOST
Other specific Country Approvals may apply. Please see product certification label.
This document applies to models IN72, P720, IN74, P740, IN76, P760, IN78.
InFocus reserves the right to alter product offerings and specifications at any time without notice.
1
Table of Contents
Composite (RCA) video connection
RS-232 connections (IN74/IN76/IN78 only)
Replacing the projection lamp 29
Red LED behavior and projector errors 32
Remote control discrete codes
Projector dimensions for ceiling mount installations
33
RS-232 terminal specifications for IN74/IN76/IN78
2
Important Operating Considerations for Safety
• Place the projector in a horizontal position no greater than 15 degrees off axis.
• Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
• Locate the projector at least 4' (1.2 m) away from any heating or cooling vents.
• Use only InFocus-approved ceiling mounts.
• Use only the power cord provided. A surge-protected power strip is recommended.
• Refer to this guide for proper startup and shutdown procedures.
•
Warning:
Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
• In the unlikely event of a lamp rupture, particles may exit through the projector side vents. When the projector is turned on, keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.
Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty booklet.
8’ / 2.4
m
5’
/ 1
.5
m
3’ / 1 m
3’ / 1 m
2’
/ 0
.6
m
Introduction
Your new InFocus projector is specifically designed for home theater applications. It sets a high standard using the latest DLP™ technology and new
DNX video processing from Pixelworks™. Whether you are watching movies or High Definition broadcasts or playing the latest video game, you will enjoy amazing image quality. The unique design and color of the projector make it a welcome addition to your home.
The projector is available in 3 different resolutions:
• IN72 has 854x480 resolution (480p)
• IN74 has 1024x576 resolution (576p)
• IN76/IN78 have 1280x720 resolution (720p)
This advanced reference guide covers all 4 models. Differences between the models are noted.
Product specifications
To read the latest specifications, be sure to visit our website at www.infocus.com as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed on the included user’s guide. Optional accessories can be found on our website at www.infocus.com or at your retailer or dealer.
Online Registration
Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives. zoom (outer ring) focus remote control receiver (IR) connector panel
3
base keypad
Connector Panel
The projector provides the following connection options:
• M1-DA/DVI (Digital Visual Interface)
• HDMI™ (High Definition Multimedia Interface)
• Component (RCA)
•
SCART RGB (you must enable this connector, see page 26)
• S-video
• Composite video (RCA)
See “Video connectors” on page 7 for details.
The projector also provides the following connectors:
• RS-232 for serial control (not included on the IN72)
• 12 volt DC output (see below)
12 volt DC output
The 3.5mm mini-jack trigger provides a 12 volt, 0.25 amp DC output. It provides a constant output while the projector is on. It has numerous uses. For example, if you connect your projection screen to the 12 volt DC output with the cable that came with your screen, when you turn on the projector the screen will move down; when you turn the projector off, the screen will return to the storage position. component RCA
12 volt
DC output
HDMI
M1-DA/
DVI
+12v ground
S-video composite
RCA
RS-232
(not on IN72)
3.5mm plug
12 volt DC output to, for example, screen relay (see screen manufacturer for details)
4
Positioning the projector
To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some guidelines:
• Position the projector on a flat surface at a right angle to the screen. The projector must be at least 4.9 feet (1.5m) from the projection screen.
• For safety reasons, position the projector within 10 feet (3m) of your power source (running extension cables may introduce a trip hazard).
To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object.
• If you are installing the projector on the ceiling, refer to the installation guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 26. We recommend
using an InFocus authorized ceiling mount.
• Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.
• The image offset is 128% for the IN72. This means that if you have an image 10’ high, the bottom of the image will be 2.8’ above the center of the lens. For the IN74/ IN76/IN78, the image offset is 115%.
10 ft high image bottom of image
2.8 ft above center of lens
Projection angle in 16:9 mode
Table 1:
Range of distance to the screen for a given screen size for the IN72
Diagonal
Screen Size
(inches/m)
60/1.5
80/2
92/2.3
150/3.8
Distance to screen
Maximum
distance
(feet/m)
9.3/2.8
12.3/3.8
14.2/4.3
23.1/7
Minimum
Distance
(feet/m)
7.8/2.4
10.4/3.2
12/3.7
19.5/5.9
Table 2:
Distance to the screen for a given screen size for the
IN74/IN76/IN78
Diagonal
Screen Size
(inches/m)
60/1.5
80/2
92/2.3
150/3.8
Distance to screen
Maximum
distance
(feet/m)
8.3/2.5
11.1/3.4
12.8/3.9
20.8/6.3
Minimum
Distance
(feet/m)
6.6/2
8.8/2.7
10.1/3.1
16.4/5
NOTE
: Visit the Service section of our website at www.infocus.com/calculator for an interactive image size calculator.
lens center
5
Choosing the aspect ratio
Aspect ratio is the ratio of the image width to image height. HDTV and most DVDs are 16:9, which is the default for this projector. When in 4:3 mode the projector places black bars on both sides of the image. Native mode centers the image and turns off the internal scaler so that any resolution larger than the native projector resolution is cropped on the edges. Letterbox expands the image to fill the screen.
What you plan to project will also help you choose between 4:3 and 16:9. For example, most TV shows are 4:3, while most movies are 16:9. If you have a
16:9 screen, then you should select an aspect ratio of 16:9 for anamorphic movies and HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for anamorphic movies or HDTV, but you also have the option of using 4:3, Native, or Natural Wide for 4:3 content. Keep in mind that anamorphic movies only appear correctly if the DVD player is set to output to a 16:9 television. Natural Wide stretches a 4:3 image to fill the entire 16:9 screen. The center two-thirds of the image is unchanged; the edges of the image are stretched.
16:9 aspect ratio
4:3 aspect ratio letterbox aspect ratio natural wide aspect ratio
9
16:9 image input
16
4:3 image input
3
9
16:9 image
16
4:3 image on 16:9 screen
3
4 letterbox image input black bars black bars
4
4:3 image input
3
9
9
16
16:9 image fills 16:9 screen
9
16
4:3 image fills 16:9 screen
4
16
6
Video connectors
The first step for connecting video is determining what type of output connectors your video device has. If there is more than one output, select the one with the highest quality. The best quality ranking, with 1 being the highest, is:
1
M1-DA/DVI or HDMI (both are digital inputs)
2
component /SCART RGB video (RCAs)
3
S-video
4
composite video (RCA)
If your device has a VGA connector, you can use the M1-DA/DVI connector for a high quality image. Many PC game systems have VGA connectors. component RCA
For detailed information on supported video formats, see page 35.
SCART (all 4 connectors)
12 volt
DC output
HDMI
M1-DA/
DVI
S-video composite
RCA
RS-232
(not on IN72)
7
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. Connect the audio from your video device to your stereo system to get sound.
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.
A composite video cable is provided with your projector so you can quickly and easily connect a video source to the projector and see the amazing image that is displayed. Once you have determined a more permanent location for your projector, we recommend purchasing higher quality cables in the proper length to get the best image from your particular video equipment. High quality cables optimized for your projector can be purchased from www.infocus.com/store (in select areas) or from your dealer or retailer.
Composite (RCA) video connection
Plug the composite video cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow
Composite
connector on the projector.
S-video connection
If your video device uses a round, four-prong S-video connector, plug the
S-video cable into the S-video connector on your video device and into the
S-video
connector on the projector.
Component (RCA) connection
If your device uses component connectors, plug a component video cable with red, green, and blue RCA connectors into the source device’s component connectors and the Component connectors on the projector.
SCART RGB connection
SCART (from Syndicat des Constructeurs d'Appareils Radiorécepteurs et
Téléviseurs) is a French-originated standard and connector for connecting audio and video equipment to display devices. The video signal is separated into its primary components for brighter, more accurate colors and sharper detail. You must enable this connector in the Source Enable menu to
use it, see page 26. You will also need a SCART to 4-RCA adapter to connect
to your SCART device.
8
Digital connections
The M1-DA/DVI and HDMI (High-Definition Multimedia Interface) connectors are digital and yield the highest quality image. It is common for these signals to be encrypted with HDCP (high-bandwidth digital-content protection). Your new projector ships standard with decryption codes so you can enjoy these high quality, all digital images.
This projector uses the M1-DA connector, which has the following advantages:
• allows connection to a digital DVI source
• allows connection to a component source
• allows connection to an analog computer source
• carries a USB control signal which allows you to easily update your projector’s software as enhancements become available.
• has output pins that can power accessories.
The IN76 and IN78 are HDTV (High Definition Television) monitors, meaning they have vertical scanning lines of 720 progressive, 1080 interlaced or higher. The IN72 and IN74 are EDTV (Enhanced Definition Television) monitors, meaning they have vertical scanning lines of 480 progressive or higher. HD content can be displayed on an EDTV monitor, the resolution is just less than that of an HDTV.
DVI connection
If your video device uses a DVI connector, plug the DVI end of an M1-DA cable into the video-out connector on the video device. This connector may be labeled “To Monitor” on the video device. Plug the M1-DA end of the cable into the M1-DA/DVI connector on the projector.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connector on the projector.
An M1-DA to HDMI adapter is included with the IN78. This plugs inot the
M1-DA connecotr and allows a second HDMI source to be connected. Note:
DVI, VESA, and USB connections are not available when adapter is connected.
Note that the projector has no audio capabilities, so audio signals transferred through HDMI will not be audible.
Computer connections
You can connect a computer’s VGA connector to the M1-DA/DVI input on the projector using an M1-A cable.
RS-232 connections (IN74/IN76/IN78 only)
You can control the projector from an LCD control panel or computer by connecting an RS-232 cable to the projector’s Serial control connector. Specific RS-232 commands can be found in the Service section of our website at
www.infocus.com/support
.
9
Displaying an image
Connect the power cord to the Power connector on the back of the projector and to your electrical outlet.
NOTE
: Always use the power cord that shipped with the projector.
Press the Power button on the remote or keypad.
The LED flashes green and the fans start to run. When the lamp comes on, the start-up screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness.
? No start up screen?
Plug in, connect, and turn on your video device.
The video device’s image should appear on the projection screen. If it doesn’t, press the Source button on the keypad until the image appears.
? No image?
Try pressing the Auto Image button on the remote. Get
plug in Power cord press Power button turn on video device
Adjusting the image
Adjust the height of the image by tilting the projector up or down. adjust height
Position the projector the desired distance from the screen at a 90 degree angle to the screen.
See page 5 for a table listing screen sizes and distances to the screen.
adjust distance
10
Adjust the zoom and focus.
adjust zoom (outer ring) and focus
If the image is not square, adjust the keystone using the Picture menu. See
adjust keystone
Adjust the volume on your stereo receiver.
adjust volume
Your projector has been factory optimized for very good performance no matter what the source. However, if you wish to make further changes you can optimize the image using onscreen menus. Adjust the Contrast, Bright-
ness, Color, Tint, or Aspect Ratio in the Picture menu. See page 22 for help
with the menus and these adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 6.
adjust Picture menu options including Aspect Ratio
11
Shutting down the projector
Power Save
The projector also has a Power Save feature that automatically turns the lamp off after no active sources are detected and no user interaction with the projector is performed for 20 minutes. By default, this feature is on. See
Sleep Timer
The projector also has a sleep timer feature that automatically turns the pro-
jector off after 4 hours. See page 26.
Turning off the projector
Press the Power button on the remote or keypad to turn the projector off.
The lamp turns off and the LED blinks green for one (1) minute while the fans continue to run to cool the lamp. While the LED is blinking green, the projector does not accept any user input. Once the cooling process is complete, the LED lights solid green and you can turn the projector back on, if desired.
NOTE
: Once the projector has been turned off, you must wait for one (1) minute before turning the projector on again. This allows the lamp to properly cool. The LED lights solid green when the cooling process is complete.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup.
The LED on top of the projector indicates the state of the projector and can help you troubleshoot.
Table 3: LED behavior and meaning
LED color/behavior
solid green blinking green blinking red
see page 32 for more information
solid red
Meaning
The power button has been pressed and the software has initialized or the projector has been powered off.
The power button has been pressed and the software is initializing, or the projector is powering down and the fans are running to cool the lamp.
A fan or lamp failure has occurred. Make sure the vents aren’t blocked (see
page 16). Turn off the projector and wait
one minute, then turn the projector on again. If the projector has exceeded its
lamp life (page 29), replace the lamp and
reset the lamp timer. Contact Technical
Support if the problem persists
.
An unidentifiable error: please contact
Technical Support.
The following tables show common problems. In some cases, more than one possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
12
Problem no start up screen only start up screen appears
Startup
Screen
Solution
plug power cord in back of projector
press power button
press power button
Result correct image connect active source press the Source button
image projected
Video
Image
13
Problem image not centered on screen
Solution move projector, adjust zoom, adjust height
Result correct image image not square tilt the projector up or down or adjust
Keystone in Picture menu square image
14
image not sharp adjust Sharpness in the Picture>Advanced menu correct image
A B
image upside down
AB
turn off ceiling in Settings>System menu correct image
A B
15
image reversed left to right
A
projected colors don’t match source turn off rear in Settings>System menu correct image
A B
adjust color, tint, color temperature, brightness, contrast in the menus correct image
COLOR
lamp won’t turn on, LED blinking red
LED
COLOR
make sure vents aren’t blocked, turn off the projector and allow it to cool for one minute lamp turns on
16
“Change lamp” message appears at startup or LED blinking red
lamp must be replaced (see page 29)
LED
message disappears, LED stops blinking red replace lamp, reset lamp timer
Still need assistance?
If you need assistance, visit our website at www.infocus.com or call us. See the User’s Guide for support contact information. This product is backed by a limited warranty. An extended warranty plan may be purchased from your retailer or dealer.
When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.
17
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the front of the projector (not at the video device or computer). The range of optimum operation is up to 30 feet (9.14m).
Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 21 for more info on the menus.
The remote also has:
•
Power
button to turn the projector on and off (see page 12 for shut-
down info)
• backlight button to light the remote’s buttons in the dark
•
Source
buttons to switch among sources (to assign a particular source
to a source button, see page 26) and a source toggle
•
Resize
button to change the Aspect Ratio (see page 22)
•
Auto Image
button to resynch the projector to the source
•
Preset
button to select stored settings (see page 23)
•
Overscan
button to remove noise at the edge of a video image
•
Custom
button that can be assigned to a special function, like Blank
Screen or Freeze (see page 27).
•
Backlight/Flashlight
button on the underside of the remote. Press this button once to light up the remote, press and hold it to turn on the flashlight.
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are not dead.
• Make sure you’re pointing the remote at the front of the projector or at the screen, not at the video device or the computer, and are within the remote range of 30 feet (9.14m).
navigation buttons backlight/flashlight button (on underside of remote)
18
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Menu
–opens the on-screen menus (page 21).
Select
–confirms choices made in the menus (page 21).
Up/Down arrows
–navigates to and adjusts settings in the menus (page 21).
Power
–turns the projector on and off.
Source
–changes the active source. menu navigation buttons
19
Optimizing video images
Your projector has been factory optimized for very good performance no matter what the source. However, if you wish to make further changes you can optimize the image using onscreen menus. For general information on
• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
•
Select a Sharpness setting (page 24).
•
Use the Color Control to adjust the color gain and offset (page 25).
•
Adjust the Color Temperature. Select a listed value (page 25).
• Turn on Overscan to remove noise on the edges of the video image
•
Change the Aspect ratio (page 22). Aspect ratio is the ratio of the image
width to image height. TV screens are usually 1.33:1, also known as 4:3.
HDTV and most DVDs are 1.78:1, or 16:9 (the projector’s default).
Choose the option that best fits your input source in the menus, or press the Resize button on the remote to cycle through the options. See
•
Select a specific Color Space. See page 24.
• Select a different Video Standard. Auto tries to determine the standard of the incoming video. Select a different standard if necessary. See
• Make sure your DVD player is set for a 16:9 television. See your DVD player’s user’s guide for instructions.
Customizing the projector
You can customize the projector for your specific setup and needs. See
page 26 to page 28 for details on these features.
• For rear projection, turn rear mode on in the Settings>System menu.
• For ceiling mounted projection, turn ceiling mode on in the Set-
tings>System
menu.
• Turn the projector’s display messages on and off.
• Turn on power saving features.
• Specify blank screen colors and start up logos.
• Specify the language viewed on the menus.
• Save settings for the active source as a preset.
20
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, navigate to Previous or Exit, then press Select to go to the previous menu; press the Menu button at any time to close the menus.
Dots appear before the menu name. The number of dots indicate menu’s level, ranging from one (the Main menu) to four (the most nested menus).
The menus are grouped by usage:
• The Picture menu provides image adjustments.
• The Settings menu provides set-up type adjustments that are not changed often.
• The Source Info menu provides a read-only display of information about the projector and source.
Certain menu items may not be visible or may be grayed depending upon a particular source being connected. Differences are also seen in analog versus digital video sources and interlaced versus progressive sources.
Menu options are grayed out only if the source is selected but no signal is present. For example, if the projector is set to a video source but the source, such as a DVD player, is turned off video menu options are grayed out.
Main menu
Picture menu dots keypad navigation buttons
Settings menu
Source Info menu
21
Picture menu
To adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes.
Keystone
: adjusts the image vertically and makes a squarer image. Tilt the projector up or down to adjust for keystone before using the digital keystone correction in the menu.
Image Shift (IN78 only)
: moves the image vertically. Use it to shift the image, or to mask artifacts or bars on the top or bottom of the image
Contrast
: controls the degree of difference between the lightest and darkest parts of the picture.
Brightness
: changes the intensity of the image.
Color
: adjusts a video image from black and white to fully saturated color.
Tint
: adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only.
Aspect Ratio
: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The projector’s
default is 16:9. See “Choosing the aspect ratio” on page 6 for more informa-
tion.
Select Native to see the unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs. Select Letterbox to preserve the 16:9 aspect ratio. If you have a 16:9 source and screen, the image fills the screen. If your source is letterboxed, the image is expanded to fill the screen. Select Natural Wide to stretch a 4:3 image to fill the entire 16:9 screen. The center two-thirds of the image is unchanged; the edges of the image are stretched.
For more information regarding Aspect Ratio, see page 6.
22
Picture menu increasing keystone decreasing keystone
Aspect ratio
Presets
: This allows you to customize settings and save the settings to be restored later. To restore the factory default settings, choose Factory Reset in the Settings>Service menu.
To set a preset for the current source, adjust the image, select Save Settings in the Presets menu, then choose Save User 1, 2, or 3. You can recall these settings in the future by selecting the appropriate user presets. All settings in the Picture menu (except Keystone) are saved and recalled.
ISF Day/Night (IN78 only)
: Supports certified Imaging Science Inc. calibration. ISF presets are not available until after calibration is performed, and picture settings cannot be adjusted when ISF presets are active. For more information go to www.infocus.com/service.
Gamma
: Gamma tables contain preset intensity configurations optimized for the input source. You can select a gamma table that has been specifically tuned for either film, CRT (Cathode Ray Tube), video, PC, or Bright Room input. (Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a
TV show or sporting event.) White Peaking increases the brightness of whites that are near 100%.
NOTE
: Your viewing preferences may vary. Cycle through the gamma options and pick the one you like the best.
Presets
Save
User
Settings
Gamma
23
Advanced menu
Remember that not all options in the menus are available for all sources/ signals.
Phase
: adjusts the horizontal phase of a computer source.
Tracking
: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position
: adjusts the position of a computer source.
Sync Threshold Adjust
: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, adjust this option to help it to sync when connected to the projector.
Flesh Tone Correction
: this modifies colors to make the skin complexion better.
Black Level Calibration (IN78 only)
: automatically adjusts brightness to get the best black level. Before using, make sure there are black bars at the top, bottom, or sides of the image.
Film Mode
: controls deinterlacing and is On by default. When checked, it assumes the incoming signal is film material and optimizes the image accordingly.
Sharpness
: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.
Color Space
: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources, choose either REC709 or REC601 for component video sources.
24
Sharpness
Color Space
Advanced menu
Color Temperature
: changes the intensity of the colors. Select a value.
Native means an uncorrected/unchanged color temperature. Other values change the white point of the colors. 6500K is generally used for film content and 9300K is used for TV video.
Color Gamut (IN78 only):
sets the total number of possible displayable colors (gamut). Choose Auto to have the projector select automatically based on the current signal format. Choose Maximum to display all colors that the projector is capable of displaying.
InFocus Color Gamut Calibrator software allows a professional installer to define optimized color calibration coordinates for the IN78. For more information go to www.infocus.com/service.
Color Control
: allows you to individually adjust the gain and offset of the red, green, and blue colors. These advanced controls have the same effect as contrast and brightness, but each controls a single color only.
Video Standard
: when it is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Overscan
: removes noise around the edges of the video image. Select Zoom to remove the outer 3% of the image and scale the image back up to its original size. Select Crop to remove the outer 3% of the image without rescaling the image.
Noise Reduction
: adjusts signal noise reduction. Choose Enable then adjust the level. The software determines the differences between successive image frames and averages the changes out to reduce the noise.
25
Color
Temperature
Color Control
Video Standard
Overscan
Noise Reduction
Settings menu
Sources:
allows programming of source buttons, enables autosource, and enables the SCART RGB source. When Autosource is selected, the Source
Enable
feature indicates which sources the projector attempts to lock onto.
You can use the Source Enable feature to eliminate certain sources from this search, which will speed the search. By default, the check boxes for all sources are checked except SCART RGB. Uncheck a source box to eliminate it from the search. When Autosource is not checked, the projector defaults to Component initially, then defaults to whatever the last active source was when the projector was powered down. To display another source, you must manually select one by pressing the Source button on the remote or keypad. This cycles through all the sources that are selected in the Source
Enable menu.
The Source 1, 2, and 3 menus in the Sources menu allow you to assign a source to the Source 1, 2, and 3 buttons on the remote. The Source 4 menu selection would apply to the Custom key if that option is chosen in the Cus-
To use the SCART RGB source, you must first select it in the Source Enable menu (the projector cannot automatically detect this source). Enabling
SCART will disable Component and Composite sources.
System>Rear
: reverses the image so you can project from behind a translucent screen. Ceiling: turns the image upside down for ceiling-mounted projection.
Auto Ceiling:
uses an internal sensor to automatically turn on ceiling mount mode if the projector is inverted. High Power: maximizes the light output of the lamp. Auto Power: When Auto Power is checked, the projector automatically goes into the startup state after the projector receives power. This allows control of ceiling mounted projectors with a wall power switch Display Messages: displays status messages (such as
“Searching”) in the lower-left corner of the screen.Translucent OSD: makes the menus translucent. This prevents the image from being completely covered by the menus while you are making image adjustments. Sleep Timer: automatically turns off the projector after 4 hours. Power Save: automatically turns the lamp off after no signals are detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image is displayed.
26
Sources
Settings menu
System menu
Source
Enable
Startup Logo:
allows you to display a blank screen or a custom captured image instead of the default screen at startup.
To capture a new image, display the image and select Capture New. A message appears. Select Captured in the Startup Logo menu to display your new image. Note that this feature will not work on interlaced signals.
Blank Screen
: determines what color is displayed when you select Blank
Screen in the Startup Logo menu and when no source is displayed.
Language
: allows you to select a language for the onscreen display.
Startup Logo
Language menu
Blank Screen
Custom key:
allows you to assign a different function to the Custom key on the remote, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.
•
Blank Screen
: displays a solid blank image.
•
Freeze
: takes a snapshot of the projected image. If you’re watching video, the source video continues to run but the image is frozen.
•
Source Info
: the default effect. It opens a window with projector and source information.
•
Service Info:
opens the Service info window.
•
Source 4
: selects source 4 (by default, Source 4 is the Composite input).
This gives you 4 direct source options on the remote. See page 26.
27
Custom Key
Service
: To use these features, highlight them and press Select.
Factory Reset
: restores all settings to their default.
Reset Lamp hours
: resets the lamp hours used counter in the Service
Info menu to zero. Do this only after changing the lamp.
Test Pattern
: displays a test pattern. To display test patterns, first you
must assign Blank Screen to the Custom key (page 27), then click the
Test pattern check box in the Service menu to turn the option on, exit the menus, then press the Custom button on the remote. To select the patterns, use the up/down arrows on the remote or keypad. To exit the test patterns, press the Custom button.
Blue Only
: turns off the Red and Green portions of the input, allowing you to properly adjust the color balance with a SMPTE color bar pattern.
HDMI DDC
: turns the EDID extension on and off. Some graphic cards cannot recognize the projector’s EDID. By default, the HDMI EDID extension is on (checkbox is checked) and the M1-DA EDID extension is off (checkbox unchecked). Change these settings if you have trouble using HDMI or DVI sources.
Service Info
: provides information about the projector’s software, serial number, and lamp.
Service Code
: only used by authorized service personnel.
Source Info
: provides information about the active source.
28
Source Info menu
Service menu
HDMI menu
Service Info
Maintenance
Cleaning the lens
1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion.
Replacing the projection lamp
The lamp hours timer in the Service Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, a message appears on the screen at startup indicating that you should change the lamp. The LED on top of the projector also blinks red twice to indicate that the lamp should be changed.
NOTE
: You can order new lamp housings from www.infocus.com (in select areas), your retailer or your dealer. Use only a replacement lamp with the same type and rating as the original lamp.
1
Turn off the projector and unplug the power cord. If ceiling mounted, disconnect all cables and detach the projector from the ceiling mount.
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside down on a soft cloth so that the lamp door is facing you. Remove the base or ceiling mount plate, if attached, by removing the 3 screws.
29
turn off and unplug projector
Lamp hours used wait 60 minutes
4
Push the 2 tabs on the lamp door toward the front of the projector and lift the lamp door off.
5
Loosen the three captive screws that attach the lamp housing to the projector.
6
Detach the lamp connector from the projector by depressing the locking tab on the connector and lightly pulling it free.
WARNING
:
To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
Be extremely careful when removing the lamp housing. In the unlikely event that the bulb ruptures, small glass fragments may be generated. The lamp housing is designed to contain these fragments, but use caution when removing the lamp housing. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.
Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org
.
7
Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner.
8
Install the new lamp housing and tighten the screws.
9
Re-attach the lamp connector to the projector. The locking tab should engage when the connector is fully plugged in.
lamp door captive screws
30
lamp housing lamp connector
10
Replace the lamp door.
11
Replace the base or ceiling mount plate, if necessary.
12
Plug in the power cord and press the Power button on the remote or keypad to turn the projector back on.
13
To reset the lamp hour timer, navigate to the Settings>Service menu
and select Reset Lamp Hours. See page 28 for details.
Service menu
31
Appendix
Red LED behavior and projector errors
If the projector is not functioning properly and the LED is blinking red, consult Table 4 to determine a possible cause. There are two-second pauses between the blinking cycles. Visit our website for more details on the red
LED error codes.
Table 4: LED Behavior
Red LED Behavior
One (1) blink
Two (2) blinks
Three (3) blinks
Four (4) blinks
Five (5) blinks
Explanation
The lamp won't strike after five (5) attempts. Check the lamp and lamp door installations for loose connections.
The lamp counter hours have exceeded lamp life hours. Replace the lamp and reset the lamp hours counter.
The projector has shut down. Check to see if the lamp door is open. If the lamp door is closed, toggle off the projector and wait one minute, then toggle the projector on again. If the lamp does not strike after one minute, replace the lamp. Contact Technical Support for repair if replacing the lamp does not solve the problem.
The fan has failed. Contact Technical Support for repair or replacing the fan.
The projector is overheating. Check for a
blocked air vent (page 16). Contact Tech-
nical Support for repair if clearing the vents/screens does not solve the problem.
32
Remote control discrete codes
You can use these codes to program another remote to learn the projector’s remote functions.
To activate discrete mode, press and hold the Custom button on the remote for 10 seconds. The back light blinks twice when discrete mode is entered.
The remote buttons are now remapped to new functions as listed below. To return to normal remote mode, press and hold the Custom button on the remote for 10 seconds. The remote also returns to normal mode automatically if no activity is detected for 2 minutes.
Table 5: Remote control discrete codes
Function Description
Remote button
Power off
Power on turns power off turns power on
Native resize selects Native resize
16:9 resize selects 16:9 resize
4:3 resize
Letterbox resize selects 4:3 resize selects letterbox resize
Nav Up
Nav Down resize overscan source custom
Natural wide resize selects natural wide resize
User preset 1 selects user preset 1
User preset 2 selects user preset 2
User preset 3 selects user preset 3 auto image
Source 1
Source 2
Source 3
33
Projector dimensions for ceiling mount installations
All values in millimeters (mm).
234.5
361
126.5
121
40.25
57
64
167
24.5
40.5
163
227.5
245.5
344.25
34
Supported video formats
Connector
HDMI
M1-DA
Component
Composite
S-video
RGBS
Digital RGB and YCrCb
(HDCP or non-HDCP)
Digital RGB video via M1-to-DVI cable
(HDCP or non-HDCP)
Analog RGB video via M1-to-VESA cable
YPrPb video via M1-to-Component adapter
Analog Computer via M1-to-VESA cable
Digital Computer via M1-to-DVI cable
YPrPb
Signal Type
Standard definition TV composite video sources
S-VHS Y/C
RGB-C or RGB-S via SCART-to-4 wire RGB adapter cable
Supported formats
480i/p/50Hz/60Hz
576i/p/50Hz/60Hz
720p/50Hz/60Hz
1080i/50Hz/60Hz
1080i/50Hz (Australia)
1080p/24Hz
(IN76/78 only)
1080p/50Hz
1080p/60Hz
All industry-standard analog and digital computer formats conforming to
VESA standards
480i/p/50Hz/60Hz
576i/p/50Hz/60Hz
720p/50Hz/60Hz
1080i/50Hz/60Hz
1080i/50Hz (Australia)
1080p/24
(IN76/78 only)
NTSC: M, 4.43
PAL: B,G,H,I,M,N
SECAM: M
SCART-RGB (576i/576p)
35
RS-232 terminal specifications for IN74/IN76/IN76
Communication configuration
To control the projector from an LCD control panel, connect an RS-232 cable to the serial control connector on the projector and set your computer’s serial port settings to match this communication configuration:
Setting
Bits per second
Data bits
Parity
Stop bits
Flow control
Emulation
Value
19,200
8
None
1
None
VT100
Command format
All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read request (indicated by a
“?”) or a write request (indicated by 1 to 4 ASCII digits).
A read request format: (AAA?) where
( starts the command
)
AAA denotes the command
?
denotes the read request ends the command
A read command returns the range and the current setting, for example
:
Function
Brightness
Lamp hours
Command
(BRT?)
(LMP?)
Response
(0-22, 10)
(0-9999, 421)
A write request example: (AAA####) where
( starts the command
)
AAA denotes the command
#### denotes the value to be written
(leading zeros not necessary) ends the command
Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically set to the maximum number for that function. If a command is received that is not understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on.
The one exception is the Power command, where 0 is off and 1 is on
.
Function
Brightness
Power
Power
Power
Command
(BRT10)
(PWR0)
(PWR1)
(PWR9999) ?
Response
Sets the brightness to 10
Turns power off
Turns power on
36
Supported commands
Function
Auto Ceiling Enable
Auto Color Space enable
Auto Image
Aspect Ratio
Auto Power Enable
Auto Source Enable
Auto Video Standard Enable
Blank
Blank Screen Enable
Blue Color Offset
Blue Gain
Blue Only Enable
Brightness
Ceiling
Color
APO
ASC
AVS
BLK
BLK
Command Range
ACL 0-1
ACS
AIM
ARZ
0-1
0-1
0-4
0 = Native
1 = 4:3
2 = 16:9
3 = Letterbox
4 = Natural Wide
0-1
0-1
0-1
0-1
0-1
0 = black
1 = blue
1-255 BCO
BCG
BOE
BRT
CEL
CLR
1-255
0-1
0-255
0-1
0-100
1
0
0
1
0
1
0
1
Defa ult
0
128
128
0
128
0
50
Color Space
Color Temp
Contrast
Display Messages
Factory Reset (Write only)
Flesh Tone Correction
Gamma Table
37
Green Color Offset
Green Gain
HDMI DDC Enable 1
HDMI DDC Enable 2
High Power Enable
Horizontal Position
Vertical Keystone
Lamp Hours (Read only)
Number of Lamp Resets
Menu Enable
CSM
TMP
CON
DMG
RST
FTC
GTB
GCO
GCG
EE1
EE2
HPE
HPS
DKC
LMP
LMR
MNU
0-255
0-255
0-1
0-1
0-1 n/a
0-80
0-65535
0-65535
0-1
0-2
0 = RGB
3 = REC709
2 = REC601
0-3
0 = 6500
1 = 7500
2 = 9300
3 = Native
0-255
0-1
0-1
0-1
0-8
2 = Video
3 = Film
5 = Bright Room
7 = CRT
8 = PC
0
0
128
1 n/a
0
3
0
0
0 n/a
40
0
1
0
128
128
Menu Navigation
Language
Noise Reduction Mode
Noise Reduction Level
Overscan
Phase
Power Enable
Power Save Enable
Presets
Rear Project
NAV
LAN
NRE
NRL
OVS
MSS
PWR
PSV
PST
REA
0-3
1 = up
2 = down
3 = select
0-11
0 = English
1 = French
2 = German
3 = Italian
4 = Japanese
5 = Korean
6 = Norwegian
7 = Portuguese
8 = Russian
9 = Chinese Simplified
10 = Spanish
11 = Chinese Traditional
0-1
0 = Off
1 = Auto
8-248
0-2
0-100
0-1
0-1
0-5
0 = default
1 = User 1
2 = User 2
4 = Off
0-1 n/a
0
0
0
0
0
128
0
50
0
Red Color Offset
Red Gain
Sharpness
Sleep Timer
Sync Threshold Adjust
Source
38
Source 1 Program
Source 2 Program
Source 3 Program
Source 5 Program
Startup Logo
Tint
Film Mode Auto Detect
Tracking
Total number of successful
Strike Attempts
Screen Trigger Enable
System State
Translucent OSD
Test Pattern Enable
Test Pattern Select
Total number of Strike
Attempts
RCO
RCG
SHP
SLT
STH
SRC
STE
SYS
TOE
TPO
TPS
TSA
SR1
SR2
SR3
SR4
DSU
TNT
TTO
MTS
SSA
0-5
0-5
0-5
0-2
2-98
0-1
0-100
0-65535
0-255
0-255
0-4
0-1
1-15
0-5
0 = HDMI
1 = M1-DA
2 = Component
3 = S-Video
4 = Composite
5 = SCART RGB
0-5
0-1
0-17
0-1
0-1
0-9
0-65535
0
8
2
128
128
2
0
0
0
1
0
1
3
2
50
1
0
2
3
50
0
Vertical Position
Video Standard
VPS
VSU
White Peaking
Save User1 Preset
Save User 2 Preset
Save User 3 Preset
Logo Capture Enable
Source Enable 0
Source Enable 1
Source Enable 2
Source Enable 3
Source Enable 4
Source Enable 5
Logo Capture Compress
Logo Capture Compression
Progress Count
Current Subsource
Power-up Source
Effect Key Program
System Error Code
Freeze Enabled
Lamp Power
Time in Hours Last Bulb1
Lasted
CE2
CE3
CE4
CE5
COM
CPC
WPK
US1
US2
US3
CAP
CE0
CE1
CRS
DSC
EFK
ERR
FRZ
IPM
LB1
0-1
0-1
0-1
0-1
0-1
0-1
0-1
0-1
0-100
0-9
0 = Auto
1 = NTSC
2 = PAL
5 = SECAM
0-10
0-1
0-1
0-1
0-480
0-7
0-5
0-11
0-7
0-1
0-1
0-65535
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
2
8
50
0
Time in Hours Last Bulb2
Lasted
Time in Hours Last Bulb3
Lasted
Illuminating State
Lamp Total Time On in hours for all bulbs
Perform Lamp Reset
Number of times unit has been turned on
Number of times unit has been turned on for at least 30 minutes
Number of times unit has been turned on for at least 60 minutes
Number of times unit has been turned on for at least 90 minutes
Time in minutes unit has been turned on
Time in minutes unit is currently on
Time in minutes unit was previously turned on
LB2
LB3
LML
LMT
LRT
O00
O30
O60
O90
ONC
ONL
ONP
0
0
0
0
0
0
0
0
0
0
0
0
0-65535
0-65535
0-2
0-65535
0-1
0-65535
0-65535
0-65535
0-65535
0-4294967295
0-4294967295
0-4294967295
39
INDEX
A
B
blinking green 12 blinking red 12
C
command line interface commands 37
connecting
computers 9 digital components 9
customer service contact information 17
D
40
E
F
H
I
image
K
L
LED
blinking green 12 solid green 12
M
P
projector
R
RS-232
41
S
T
V
W
Z
42
advertisement
Related manuals
advertisement