Extron electronic CTP150CM User's Manual


Add to my manuals
11 Pages

advertisement

Extron electronic CTP150CM User's Manual | Manualzz

User’s Manual

www.extron.com

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

© 2004 Extron Electronics. All rights reserved.

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

CTP150CM

7-Button Remote Control Panel

Contact Closure Control for the TPS150 Transmission System

68-994-01 Rev. A

Printed in the USA

05 04

Precautions

Safety Instructions • English

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future reference.

Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous.

Consignes de Sécurité • Français

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im

Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und

Wartung (Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und

Anleitungen auf dem Gerät oder in der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine

Gefahrenquelle darstellen können.

Instrucciones de seguridad • Español

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente recomendados por el fabricante, ya que podrian implicar riesgos.

Warning

Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them.

Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced.

Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene

Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar.

Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen

Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem

Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die

Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen

Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.

Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen

Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/ mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas siguiendo las instrucciones del fabricante.

FCC Class A Notice

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Note: This unit was tested with shielded cables on the peripheral devices.

Shielded cables must be used with the unit to ensure compliance.

Extron’s Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, and Central America:

Europe, Africa, and the Middle East:

Extron Electronics

1001 East Ball Road

Anaheim, CA 92805, USA

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

Asia:

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Bldg.

Singapore 368363

Japan:

Extron Electronics, Japan

Daisan DMJ Bldg. 6F,

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074

Japan

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification to the product.

If it has been determined that the product is defective, please call Extron and ask for an Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe),

65.6383.4400 (Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return

Authorization number). This will begin the repair process as quickly as possible.

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron

Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

Table of Contents

Chapter 1 • Introduction

.......................................................... 1-1

About the CTP150CM

........................................................... 1-2

Chapter 2 • Installation and Operation

.......................... 2-1

Installation Overview

......................................................... 2-2

UL Requirements for Wall Box Installation

.............. 2-3

Wall Mounting Site Preparation

.................................... 2-3

Wall Mounting

......................................................................... 2-6

Rear Panel Setup

................................................................... 2-7

Front Panel Operation

......................................................... 2-8

Appendix • Reference Information

.................................. A-1

Specifications

......................................................................... A-2

Parts List

.................................................................................... A-3

Included parts ........................................................................ A-3

Connected TPS150 transmission system .............................. A-3

Mini-AAP mounting options ................................................. A-3

Wall mounting solutions ................................................... A-3

Architectural solutions ....................................................... A-4

Table solutions .................................................................. A-4

Wall mounting hardware ..................................................... A-4

CTP150CM Remote Control Panel • Table of Contents i

Table of Contents, cont’d

68-994-01 Rev. A

Printed in the USA

05 04

All trademarks mentioned in this manual are the properties of their respective owners.

ii CTP150CM Remote Control Panel • Table of Contents

CTP150CM Remote Control Panel

Introduction

About the CTP150CM

About the CTP150CM

The Extron CTP150CM is a 7-button contact closure remote control panel that can be connected to the TPT150 switching transmitter of a TPS150 switching and transmission system

(figure 1-1). Each button corresponds to one of the transmitter’s front panel functions and you can operate these functions from the remote control panel or the TPT150 transmitter.

Extron

TPR150

Twisted Pair

Receiver

Extron

TPT150

Switching

Transmitter

UT P LINK

AD

SKEW

R E

D

B L U E

G

R N

RGB /

VG

A

CO

MP

VID

EO O

UT

PU

OSITE

IDEO

S-V

T

R-Y

COMPO

Y

NE

NT

B-Y

RS-232 PO

RT

60 VA

90 -2

C; 0

.2

5A

; 4 7-

63 Hz

TE CH

NI

00

(7

14

CA L S

) 8 82

) 4

50

UP

PO RT

-7 11

-1 80 c.

co m w.E

xt ro nin ww

M

IN U

.S.A

FU

SE : 1

.6

A;

2

V;

50

T

IM E

DE LA

TP

Cable

AU

DIO

IN PU

T

LO CA

L M

OU

TP

ON

IT

UT

OR R

RG

B / VG

A

IN

PU T

AU

DI O

R

RG B /

VG

A

VID

EO

S-

DE

O

Y

IN PU

T R-

Y

AU

O

DI

R

S-

VI DE

O

Y

BY

VID

EO

IN PU

T 4 R-

Y

AU

DIO

R

BY

OU

TP UT

AU DI

O

R

UP

T

NK

RE MO

CO NT

TE

RO

GN

PR OJ

P

TE CH

NIC

AL S

UP PO

RT

00

(8

32

P nc

.c

VO

L

VO L

DN

UP

W ww

RS

14

(7 w.

) 8

) 4 lin

82

50 ei

-7

-1

OR

11

80 om

IN

IN

IN

IN

FU

SE : 1

.6

2

TIM

50 V;

E D EL

AY

EC TO

R

PR OJ

PO

WE R

PC 1

PC 2

VID

EO

1

VID

EO

2

VO

LU

UP

ME

DO

WN

Extron

CTP150CM

Control

Panel

Control

System

Sound

System

VCR

Composite

Video

Input 3

DVD

Component

Video

Input 4

PC

Input 1

Laptop

Input 2

Figure 1-1 — CTP150CM as part of typical TPS150 system

The remote control panel is incorporated into a four space mini-AAP enclosure that can be mounted into a variety of

Extron mini-AAP architectural options, including wall plates

(such as the CPM101), table-mounted connector bays (such as the CPM208), or an interface or other device that has its own mini-AAP mounting bays (such as the CIA111).

1-2 CTP150CM Remote Control Panel • Introduction

CTP150CM Remote Control Panel

Installation and Operation

Installation Overview

UL Requirements for Wall Box Installation

Wall Mounting Site Preparation

Wall Mounting

Rear Panel Setup

Front Panel Operation

Installation Overview

CAUTION

Installation and service must be performed by authorized personnel only. UL Listed electrical

boxes are recommended. See UL Requirements for Wall Box Installation in this chapter.

1

2

3

4

5

6

7

8

9

Power off all devices and disconnect them from the power source, if necessary.

Run an 8-conductor cable between the site where the

CTP150CP control panel module will be installed and the site of the TPT150 transmitter.

For installation in a wall or furniture , prepare the site: cut a hole in the surface, install the electrical box or mounting bracket, and prepare the cables. See Wall

Mounting Site Preparation in this chapter. See Mini-AAP

mounting options in appendix A, Reference Information, for a partial list of devices that can accept four space mini-AAPs.

For other installations , install a tabletop or in-table connector bay, or other mini-AAP mounting option.

Refer to the manual for the device in which the control panel module will be installed. See Mini-AAP mounting

options in appendix A, Reference Information, for a partial list of devices that can accept four space mini-AAPs.

Connect the 8-conductor cable between the remote control panel and the transmitter. See Rear Panel Setup, in this chapter for details.

If the rear of the control panel module will be inaccessible when the installation is complete, the operation of the panel should be tested before the final mounting.

Apply or connect power to all devices in the system.

Test the system: Ensure that the transmitter responds as desired to the remote control panel buttons. If necessary, correct the system wiring. Ensure that you remove electrical power if you need to change the system wiring.

Test the system again.

Mount the control panel module into any Extron fourspace mini-AAP connector panel.

Restore power to all devices.

2-2 CTP150CM Remote Control Panel • Installation and Operation

UL Requirements for Wall Box Installation

The following Underwriters Laboratories (UL) requirements pertain to the installation of the CTP150CM into a wall or furniture (figure 2-1).

Installation

Cable

Conduit

WE

R

R

EC

TO

PR

OJ

2.5"

H. SHIFT

1

2

INPUT SELECT

AU

DIO

2

INPUT 2

INPUT 1

AU

DIO

1

FOLLOWS

MONITOR

INPUT 1

MIN/MAX

MONITOR

VID

EO

1

VID

EO

2

VO

ME

UP

ME

VO

LU

DO

WN

RGB 478 Mxi

WITH ADSP

Extron

RGB 478 Mxi

Interface

Extron

CTP150CP

Remote Control

Panel

Figure 2-1 — CTP150CM in a four-gang wall box

1.

These units must be installed in UL listed junction boxes.

2.

These units must be installed with conduit in accordance with the National Electrical Code.

Wall Mounting Site Preparation

The remote control panel can be mounted in a wall-mountable four space mini-AAP A/V connector panel (such as a one-gang

CPM101) and then set into a wall with either a standard stud-mounted wall box or with a wall mounting bracket

(IN9181). The remote control panel can also be mounted to any wall-mountable Extron device that incorporates a four space

A/V mini-AAP connector panel, such as a three-gang RGB 468

Mxi. See Mini-AAP mounting options in Appendix A, Reference

Information, for a partial list of devices that can accept four space mini-AAPs.

Choose a location that allows cable runs without interference.

Allow enough depth for the wall box and the cables. You should install the cables in the wall or furniture, with or without conduits, before installing the mounting bracket or wall box.

The installation must conform to national and local electrical codes and to the equipment’s size requirements.

CTP150CM Remote Control Panel • Installation and Operation 2-3

Installation and Operation, cont’d

Installation using a UL listed wall box (available from Extron) is recommended for most mounting options, but the optional wall mounting bracket can be used instead. All wall boxes must be at least 1.0" (2.5 cm) deep.

Before using the wall mounting bracket, verify that the installation conforms to national and local electrical codes.

Prepare the site as follows:

1 .

If your wall box or mounting bracket includes a paper template , cut out the indicated portions of the template.

If the wall box or mounting bracket does not include a template, use the wall box or bracket itself to size the hole.

2 .

Place the template, wall box, or mounting bracket against the installation surface, and mark the guidelines for the opening on the wall or furniture.

3 .

Cut out the wall/furniture material from the marked area.

4 .

Check the opening size by inserting the wall box or mounting bracket into the opening. The box or bracket should fit easily into the opening. Enlarge or smooth the edges of the opening if needed.

5a .

If you are using a wall box , feed cables through the wall box punch-out holes, and secure them with cable clamps to provide strain relief.

Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back and/or insulate shields with heat shrink (figure 2-2).

Screw

Braided Shield

Cable Clamp

Metal Wall Box

Install Cable

Foil Shield

Figure 2-2 — Grounding outer braided and foil shields

To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable clamp. Both braided and foil shields should be connected to an equipment ground at the other end of the cable.

2-4 CTP150CM Remote Control Panel • Installation and Operation

5b .

If you are using a wall box , insert the wall box into the opening, and attach it to the wall stud or furniture with nails or screws, leaving the front edge flush with the outer wall or furniture surface (figure 2-3). The illustration applies to both two-gang and four-gang wall boxes.

Wall Stud

Installation

Cable

Cable Clamp

Screws or Nails

Wall opening flush with edge of box

Figure 2-3 — Attaching a wall box to a stud

If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw threads must penetrate the wood.

If attaching the wall box to metal studs or furniture, use four #8 or #10 self-tapping sheet metal screws or machine bolts with matching nuts.

CTP150CM Remote Control Panel • Installation and Operation 2-5

Installation and Operation, cont’d

6 .

If you are using a mounting bracket , follow the directions, if any, that came with the mounting bracket to attach the clips that fasten the bracket to the wall or furniture (figure 2-4).

Wall

Push Mounting

Tabs Forward

Extron

IN9181 Wall

Mounting Bracket

Figure 2-4 — Attaching a mounting bracket to a wall

Wall Mounting

1.

Sandwich the mini-AAP panel (such as a CPM101) between the body of the remote control panel and the printed front panel. Secure the front panel to the remote control panel body with the included #4-40 screws

(figure 2-5).

Extron

CPM101

A/V Connector Panel

Wall opening flush with edge of box

PR

OJECT

PO

WER

OR

PC 1

PC 2

VIDEO 1

VIDEO 2

VO

LUME

UP

DO

WN

Extron

CTP150CM

Control Module

Front Panel

Figure 2-5 — Attaching the mini-AAP panel to a wall box

2-6 CTP150CM Remote Control Panel • Installation and Operation

2.

If not already accomplished, attach the 8-conductor cable to the rear of the remote control panel.

3.

Mount the CPM101 or other mini-AAP panel (with the attached remote control panel) to the wall box or mounting bracket using the two included mounting screws (figure 2-5).

Figure 2-5 shows a wall box installation. Mounting the mini-AAP panel to a mounting bracket is identical.

4.

Power on all devices.

Rear Panel Setup

1

CTP150CM Control Panel

Input 1

Input 2

Input 3

Input 4

Volume up

Volume down

Projector power

Ground

CONTACT

CLOSURE

GND

PROJ PWR

VOL DN

VOL UP

IN4

IN3

IN2

IN1

TPT150

Switching

Transmitter

Figure 2-6 — Rear panel view

CONTACT

CLOSURE

IN4

IN3

IN2

IN1

GND

PROJ PWR

VOL DN

VOL UP

MADE IN USA

1 Contact closure connector — This connector is a 3.5 mm, 8-pole captive screw connector for contact closure connections.

Connect a Category (Cat) 5 cable or any 8-conductor cable between the remote control panel and the switching transmitter, as shown in figure 2-6.

CTP150CM Remote Control Panel • Installation and Operation 2-7

Installation and Operation, cont’d

Front Panel Operation

The control panel (figure 2-7) emulates many front panel controls of the TPT150 transmitter. See the TPS150 manual for more details for each control.

1

1

1

1

PC 1

PC 2

VIDEO 1

VIDEO 2

PROJECTOR

POWER

VOLUME

UP

DOWN

2

3

3

Figure 2-7 — Front panel

1

2

3

Input select buttons — The PC 1, PC 2, Video 1, and Video 2 buttons select video and audio inputs 1 through 4 on the TPT150 transmitter.

Projector Power button — The Projector Power button commands the TPT150 transmitter to issue the projector power on or off command. See the TPS150 manual, chapter 4, Serial

Communications, to specify the command(s) to be sent.

Volume Up and Down buttons — The Volume Up and Down buttons command the TPT150 transmitter to increase and decrease the output volume and input level.

Output volume —

Press and release the Volume Up or Down button to increase or decrease the output volume by 1 dB per push of the button or press and hold the button to ramp the output volume up or down.

Input audio level —

1 .

Press and hold the desired input select button.

2 .

While you continue to hold the Input Select button, press and release the Volume Up or Down button to increase or decrease the selected input’s volume or press and hold the button to ramp the selected input’s volume up or down.

3 .

Release the input select button.

2-8 CTP150CM Remote Control Panel • Installation and Operation

CTP150CM Remote Control Panel

Reference Information

Specifications

Parts List

Specifications

Control/remote — TPS150

Contact closure ............................ (1) 3.5 mm captive screw connector, 8 pole

Contact closure pin configurations 1 = input 1, 2 = input 2, 3 = input 3,

4 = input 4, 5 = volume up,

6 = volume down, 7 = projector power,

8 = GND

General

Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /

10% to 90%, noncondensing

Operating +32° to +122°F (0° to +50°C) /

10% to 90%, noncondensing

Rack mount .................................. No, but furniture mountable with an optional CPM Series faceplate

Enclosure type .............................. Metal

Enclosure dimensions

Faceplate ................... 2.8" H x 2.2" W x 0.1" D

(7.1 cm H x 5.6 cm W x 0.3 cm D)

(four space MAAP)

Device ........................ 2.8" H x 2.2" W x 0.5" D

(7.1 cm H x 5.6 cm W x 1.3 cm D)

(Depth excludes connectors and buttons.)

Product weight ............................. 0.5 lbs (0.3 kg)

Shipping weight ........................... 1 lbs (1 kg)

Vibration ....................................... ISTA 1A in carton

(International Safe Transit Association)

Listings .......................................... ETL (UL1950)

Compliances ................................. CE

MTBF ............................................. 30,000 hours

Warranty ....................................... 3 years parts and labor

All nominal levels are at ±10%

Specifications are subject to change without notice.

A-2 CTP150CM Remote Control Panel • Reference Information

Parts List

Included parts

Description

CTP150CM (black) or

CTP150CM (white)

8-pole captive screw connector

Tweeker (small screwdriver)

1/16" hex wrench

CTP150 Control Panel Module manual

Part number

60-614-10

60-614-20

10-265-05

Connected TPS150 transmission system

Description Part number

TPS150 70-369-01

Mini-AAP mounting options

Wall mounting solutions

Description Part number

CPM101B (one-gang) (black)

CPM101W (one-gang) (white)

CPM102B-1 (two-gang) (black) with cable guards

CPM102W-1 (two gang) (white) with cable guards

60-583-11

60-583-21

60-583-12

60-583-22

CPM102B-2 (two-gang) (black) without cable guards 60-583-13

CPM102W-2 (two-gang) (white) without cable guards 60-583-23

CPM103B-1 (three-gang) (black) with cable guards 60-583-14

CPM103W-1 (three-gang) (white) with cable guards 60-583-24

CPM103B-2 (three-gang) (black) without cable guards 60-583-15

CPM103W-2 (three-gang) (white) without cable guards 60-583-25

CPM104B-1 (four-gang) (black) with cable guards

CPM104W-1 (four-gang) (white) with cable guards

60-583-16

60-583-26

CPM104B-2 (four-gang) (black) without cable guards 60-583-17

CPM104W-2 (four-gang) (white) without cable guards 60-583-27

CTP150CM Remote Control Panel • Reference Information A-3

Reference Information, cont’d

Architectural solutions

Description

RGB 468 Mxi (black)

RGB 468 Mxi (white)

CIA111 (black, with cable guards)

CIA111 (white, with cable guards)

CIA111 (black, without cable guards)

CIA111 (white, without cable guards)

RGB 478 Mxi (black)

RGB 478 Mxi (white)

Table solutions

Description

CPM208-1 Mini-AAP bay

CPM212-1 Tabletop mini-AAP bay (black)

CPM212-2 Tabletop mini-AAP bay (white)

Surface mount box, one-gang

Wall mounting hardware

Description

One-gang “J” box, 2.5” deep

Two-gang “J” box, 2.5” deep

Three-gang “J” box, 2.5” deep

Four-gang “J” box, 2.5” deep

One-gang mounting bracket

Part number

60-591-02

60-591-03

60-596-12

60-596-13

60-596-22

60-596-23

60-592-02

60-592-03

Part number

60-589-13

60-590-11

60-590-21

60-639-02

Part number

980130

980084

980083

980097

IN9181

A-4 CTP150CM Remote Control Panel • Reference Information

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement