FMW51BC1
External Battery Charger
2. Insert the battery pack into one of the slots in the
battery charger as shown in the following figure
until the battery pack is firmly seated in the charger.
User’s Guide
PenCentra 130 / Stylistic LT
The FMW51BC1 external battery charger allows
you to charge up to two battery packs
simultaneously.
3. There are two status indicators on the battery
charger, one for each slot. The status indicators
change colors to represent different battery
conditions, as noted in Table 1.
Caution
Table 1: Status Indicator States
Indicator
UL Notice: FMW51BC1 External Battery Charger
PenCentra 130 Users: Use this battery charger with
the CP021031 (FMW51BP1) battery pack only.
Power
Stylistic LT Users: Use this battery charger with the
3-cell battery pack CA54200-0502 (FMW29BP2) or
6-cell battery pack CA54200-0506 (FMW29BP1) only.
Battery 1/
Battery 2
Condition
OFF
AC Adapter not connected
Green/ON
No battery installed
Green/ON
Charge complete
ON
Blink
0
Red
To charge your battery pack(s) in the external
battery charger:
1. Connect an FPSI DC power source such as AC
adapter FMWAC4A, FMWAC4B, FMWAC4C
or auto adapter FMWCB2 to the DC input on
the battery charger. The Power status indicator
on the charger turns on indicating that power
is supplied to the charger.
AC Adapter connected
OFF
Amber
Using the Battery Charger
Status
Charging
1
ON 2
Blink
1,2
Standby (Waiting to charge)
Battery pack alarm
Battery charger alarm
1
Blinks at rate of one second on, one second off.
2
If the battery charger indicates a fault condition with the
battery pack, remove the battery pack, disconnect power to
the charger, and contact your local help desk or your reseller
for further assistance.
Status
Indicators
Slide
Connector Pins
Power
1
Battery Slot 2
Battery 1
Battery Slot 1
2
DC Input
Battery 2
Rechargeable
Battery Pack
Stylistic LT and PenCentra 130 are trademarks of Fujitsu Personal Systems, Inc. © 1999 Fujitsu Personal Systems, Inc.
6/99
58-0664-00A
4. When the charged battery pack is needed,
remove the battery pack from the charger.
FCC Notice
When the battery charger is not in use, disconnect
the DC power source.
Operational Considerations
0
Issues to consider when you use the FMW51BC1
battery charger are discussed as follows:
• You can insert up to two battery packs at a time
in the battery charger. When charging two
battery packs, you can insert or remove either
battery pack independently.
• The battery charger only charges one battery
pack at a time. When two battery packs are
inserted in the charger, the battery pack installed
first is charged first.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try and correct the
interference by one or more of the following
measures:
• The battery charger will indicate a full charge
level and will not begin charging the battery pack
if the battery pack charge level is 90% or higher
when the battery pack is initially inserted in the
charger. This prevents the battery pack from
being overcharged.
• Reorient or relocate the receiving antenna.
• When you remove the battery pack from your
pen tablet, always insert a charged battery pack
in the pen tablet to replace the one that you
removed, or apply DC power.
• Consult the dealer or an experienced radio/
TV technician for help.
• The FMW51BP1, FMW29BP1, and FMW29BP2
battery packs use lithium ion battery cells which
have no “memory effect.” You do not need to
discharge or “condition” the battery pack before
charging.
Battery Pack Charge Time
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Changes or modifications not expressly
approved by Fujitsu Personal Systems, Inc.,
could void the user’s authority to operate the
equipment.
0
The approximate maximum amount of time needed
to charge a fully discharged battery pack to the 90%
level is shown in the following table. Note that when
two battery packs are installed in the charger, they
are charged sequentially (starting with the battery
pack that is installed first).
Battery Pack
3-cell
6-cell
2 of 2
Approximate
Charge Time
FMW51BP1
<2 hours
FMW29BP2
<2 hours
FMW29BP1
<3.5 hours
58-0664-00A