Kalatel DVMRe Triplex
©
Digital Video Multiplexer Recorder
User Manual
WARNING!
To prevent fire and electric shock, do not expose this product to rain or moisture.
!
The lightning flash with the arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the products enclosure
that maybe of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point, within an equilateral
triangle, is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
CAUTION!
To prevent electric shock, do not remove cover.
No user serviceable components inside. Refer
servicing to qualified service personnel.
!
CAUTION! Lithium Battery
ATTENTION
Danger of explosion if battery is
incorrectly replaced. Replace only
with the same or equivalent type
recommended by the
manufacturer.
This product contains a recyclable lithium battery.
It may be illegal to dispose of this battery
improperly under local, state, or federal laws.
Check with your local waste management officials
for disposal and recycling options.
CAUTION!
Electrostatic-Sensitive Device!
Use proper CMOS and MOSFET handing precautions, including approved
grounded wrists straps, etc., to avoid damage to this unit or its internal
components, from electric discharge.
WARNING!
This equipment generates, uses and can radiate radio frequency energy, and if not installed and used
in accordance with the instructions in this manual, may cause interference to radio communications. It
has been tested and found to comply with the limits for a Class A computing device pursuant to subpart
J of part 15 of FCC rules which are designed to provide reasonable protection against such
interference when operated in a commercial environment. This equipment has also been tested and
found to comply with the requirements for a CE Class A device and TUV safety standards.
Operation of this equipment in a residential area may cause interference, in which case the user is
required to take all measures that are necessary, at the user's expense, to correct the interference.
0150-0193F
2
Kalatel DVMRe Triplex
IMPORTANT INFORMATION
Software and/or firmware is furnished to the purchaser under a license for use on a single system.
Software and/or firmware included with this equipment are the sole proprietary property of, confidential
to, and copyrighted by GE-Interlogix Kalatel Division, Corvallis, Oregon, USA. The software/firmware
are not to be copied or disclosed in any manner without the express written consent of GE-Interlogix.
All information and specifications furnished by GE-Interlogix are believed to be accurate and reliable.
No responsibility is assumed by GE-Interlogix for neither its use nor any infringements of rights of third
parties that may result from its use. No license is granted by implication or otherwise under any patent
or patent rights of GE-Interlogix.
The KALATEL™ brand name and product model numbers are the property of GE-Interlogix.
COPYRIGHT, 2003: The contents of this manual may not be copied or reproduced in any manner or
form without the prior written consent of GE-Interlogix.
0150-0193F
3
Kalatel DVMRe Triplex
Contents
1
DVMRe Triplex Overview ...................................................................................... 7
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
DMVRe Triplex Basic Operations....................................................................... 18
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
3
Products Featured In This Manual ................................................................................... 7
Product Description.......................................................................................................... 7
Passwords......................................................................................................................... 8
Unpacking ......................................................................................................................... 9
Installation Environment .................................................................................................. 9
Associated Equipment.................................................................................................... 10
The Back Panel ............................................................................................................... 10
Power-Up......................................................................................................................... 16
Minimum Recommended Menu Setup ........................................................................... 17
Principal Operating Modes ............................................................................................. 18
The Front Panel............................................................................................................... 18
Live Viewing .................................................................................................................... 19
Playback.......................................................................................................................... 20
Recording........................................................................................................................ 22
Display Options............................................................................................................... 23
Active Cameos ................................................................................................................ 23
Sequencing ..................................................................................................................... 24
On-screen Indicators ...................................................................................................... 25
Triplex Mode................................................................................................................... 26
The Print Image Feature................................................................................................. 28
Menu System Overview....................................................................................... 30
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
0150-0193F
Menu Notation In This Manual........................................................................................ 30
Accessing The Menu System ......................................................................................... 30
Available Menus.............................................................................................................. 30
Menus In This Manual..................................................................................................... 31
Navigating The Menu System......................................................................................... 31
Menu Shortcuts............................................................................................................... 31
The Main Menu................................................................................................................ 32
Time/Date ........................................................................................................................ 32
Sequencing ..................................................................................................................... 35
Record ............................................................................................................................ 35
Alarms............................................................................................................................. 41
Macro .............................................................................................................................. 47
Motion Detection ............................................................................................................ 49
Camera Setup ................................................................................................................. 52
Archive Setup ................................................................................................................. 55
Audio Setup .................................................................................................................... 56
4
Kalatel DVMRe Triplex
3.17
3.18
3.19
3.20
3.21
3.22
3.23
4
Alarms .................................................................................................................. 65
4.1
4.2
4.3
4.4
4.5
4.6
4.7
5
Alarm Input...................................................................................................................... 65
Alarm Output................................................................................................................... 65
Alarm Acknowledge........................................................................................................ 65
On-screen Displays During Alarms................................................................................ 65
Alarm Operations During Playback................................................................................ 66
Alarm History Box........................................................................................................... 67
Searching For Recorded Alarms .................................................................................... 67
Searching ............................................................................................................. 68
5.1
5.2
5.3
5.4
5.5
6
Communications ............................................................................................................ 56
Front Panel Lock ............................................................................................................ 59
Factory Settings ............................................................................................................. 59
Passwords...................................................................................................................... 59
The QuickInstall Menu.................................................................................................... 60
The Operator Menu......................................................................................................... 61
The SystemView Menu ................................................................................................... 61
Disk Analysis Screen...................................................................................................... 69
Quick Archive to CD ....................................................................................................... 69
Motion Search ................................................................................................................. 70
Search Filters .................................................................................................................. 71
Search Results................................................................................................................ 72
WebBrowser......................................................................................................... 73
6.1
6.2
WaveBrowser Overview and Controls ........................................................................... 74
DVMRe Triplex WaveLink ............................................................................................... 76
7
Technical Specifications..................................................................................... 78
8
RS232 Event Generation/Text Insertion Protocol ............................................. 80
8.1
8.2
8.3
9
Message Structure.......................................................................................................... 80
Message Type ................................................................................................................. 80
Event Field ...................................................................................................................... 80
RS232 Remote Control Protocol ........................................................................ 82
9.1
9.2
Front Panel Button Emulation........................................................................................ 82
Configuration and Status ............................................................................................... 83
10Macro Tables........................................................................................................ 84
10.1
0150-0193F
Macro Functions Table ................................................................................................... 84
5
Kalatel DVMRe Triplex
10.2
Scheduled Macro Table............................................................................................... 85
11Warranty and Service.......................................................................................... 86
11.1
11.2
0150-0193F
Factory Service............................................................................................................... 86
Warranty and Return Information .................................................................................. 87
6
Kalatel DVMRe Triplex
1 DVMRe Triplex Overview
1.1 Products Featured In This Manual
DVMRe -4CT: Digital Video Multiplexer Recorder, Four-Channel, Color, Triplex.
DVMRe -10CT: Digital Video Multiplexer Recorder, Ten-Channel, Color, Triplex.
DVMRe -16CT: Digital Video Multiplexer Recorder, Sixteen-Channel, Color, Triplex.
Key To Model Numbers
1. DVMRe: Digital Video Multiplexer Recorder, Ethernet capable.
2. 4, 10, or 16: Maximum number of camera inputs.
DVMRe
16
C
T
1
2
3
4
3. C: Color.
4. T: Triplex.
1.2 Product Description
The DVMRe Triplex is a video multiplexer capable of recording from multiple cameras to an internal
hard drive while simultaneously providing playback. Unlike outdated time-lapse VCRs, the DVMRe
Triplex records high-resolution pictures. Digital recording improves playback quality over VCRs, and
eliminates the hassle of cleaning heads, changing tapes or servicing motors. The unit can also be
programmed to record continuously by overwriting the oldest recorded data. Depending on the setup,
the DVMRe Triplex can store from a few hours to more than 3 years of color images.
Programmable search features eliminate time consuming Fast Forwarding or Rewinding of tapes,
searching for critical data. Search for recorded images or events by alarm, time, date, motion, video
loss, camera number and ASCII cash register or ATM text.
Caution! This products primary purpose is to furnish video multiplexing and recording.
Although the unit has alarm handling and motion detection functions, they are considered
secondary features. This unit should not be the only alarm device on site.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Multiplexer functionality with built-in digital recording.
Triplex simultaneous recording, playback, and live multiscreen viewing.
Remote programming and control through the RS232, RS485 and Ethernet ports.
View live or recorded images remotely using WaveReader software.
Dual multiscreen monitor displays.
Auto-detect video mode on startup (NTSC or PAL).
Video motion detection (intrusion and activity).
Motion search.
Preview search results with thumbnail images.
Record speed selectable per camera.
Displays include full screen, sequenced, picture-in-picture, and multiscreens.
Alarm Handling with History Log. Pre- and post alarm recording, selectable per camera.
Archive onto Kalatel DVSe Disk Array, or RAID, DAT, AIT, or CD-Rs.
IEEE 1394 Firewire interface for Kalatel DVSe Disk Array or Firewire Disk Drives.
Continuous Recording with simultaneous Archiving.
PTZ control via ethernet or POTS, using CBR-KB3/J or KTD-405 keypad.
Covert camera recording (recording without display).
0150-0193F
7
Kalatel DVMRe Triplex
•
•
•
•
•
•
Auto-Daylight savings time change function.
Clock synchronization with Network Server.
Alarm Notification via email and/or TCP/IP.
Integrated WaveBrowser Software.
Dynamic IP addressing (DHCP).
One-touch image printing directly from the DVMRe.
1.3 Passwords
Passwords are provided to limit access to menus and certain functions. Two levels of password
security are provided:
•
Operator: Limited menu access, only Operator and System View menus are available.
•
Installer: Complete menu access.
As a security measure, it is recommended that the Operator and Installer passwords be changed after
installation is complete (see section 3.20). Store the passwords in the administrator’s secure files.
Default Passwords
Four-Channel Units
Password
Type
Access
Level
Changeable
by user?
Default
Password
Operator
Operator
Provides access to the Operator
and SystemView menus.
Yes
Press ‘ENTER’
4 Times
Installer
Installer
Provides access to all on-screen
menus.
Yes
3444
Factory
Defaults
Installer
Resets the multiplexer to the
factory defaults.
No
4111
Language
Installer
Provides access to the On-screen
Language menu.
No
1414
Installer
Deactivates the ethernet
password, so that the unit may be
accessed by any PC equipped with
WaveReader.
No
1111
Ethernet
Access
Reset
0150-0193F
Function
8
Kalatel DVMRe Triplex
Ten and Sixteen-Channel Units
Password
Type
Access
Level
Changeable
by user?
Default
Password
Operator
Operator
Provides access to the Operator
and SystemView menus.
Yes
Press ‘ENTER’
4 Times
Installer
Installer
Provides access to all on-screen
menus.
Yes
3477
Factory
Defaults
Installer
Resets the multiplexer to the
factory defaults.
No
8111
Language
Installer
Provides access to the On-screen
Language menu.
No
5415
Installer
Deactivates the ethernet
password, so that the unit may be
accessed by any PC equipped with
WaveReader.
No
1111
Ethernet
Access
Reset
Function
1.4 Unpacking
Check the package and contents for visible damage. If any components are damaged or missing, do
not attempt to use the unit, contact the supplier immediately. If the unit must be returned, it must be
shipped in the original packing box.
Package Contents
•
The DVMRe Triplex unit.
•
The Alarm Interface Circuit Board (P/N 0090-0077).
•
Accessory PCB (P/N 0900-0127). Audio equipped models only.
•
The User Manual (P/N 0150-0193).
•
A WaveReader Software CD (P/N 0151-0005-25W11).
•
The WaveReader Software Manual (P/N 0150-0143).
•
The Archiving Addendum (P/N 0150-0194).
•
WaveWatch User Manual (P/N 0150-0189).
•
Power Supply (P/N 4310-0020).
•
Power Cords ( 120 VAC P/N 4310-0002) and (220 VAC P/N 4310-0001).
1.5 Installation Environment
Power: Ensure that the installation site’s AC power is stable and within the rated voltage of the 12
Volt DC power supply. If the site’s AC power is likely to have spikes or power dips, use power line
conditioning or an Uninterruptable Power Supply (UPS).
Ventilation: Ensure that the location planned for the installation of the unit is well ventilated. Take
note of the locations of the cooling vents in the unit’s enclosure, and ensure that they are not
obstructed.
Temperature: Consider the unit’s operating temperature (0 to 40 °C) and non-condensing humidity
specifications (10% to 80%) before choosing an installation location. Extremes of heat or cold beyond
the specified operating temperature limits may cause the unit to fail. Do not install the unit on top of
other hot equipment. Leave space between rack mounted units.
0150-0193F
9
Kalatel DVMRe Triplex
Moisture: Do not expose the unit to rain or moisture. Moisture can damage the internal components.
Do not install the unit near sources of water.
Chassis: Other equipment may be placed on top of the unit if it weighs less than 35 pounds (16
kilograms).
1.6 Associated Equipment
Associated equipment in a typical security system could contain the following items:
•
Two monitors
•
A Keyboard (KB3 or KTD405).
•
Video cameras: Composite video, 1 volt peak-to-peak.
•
Alarm input devices: Pressure sensors, motion detectors, etc.
•
Alarm output devices: Buzzers, Sirens, Flashing Lights, etc.
•
A PC connected via ethernet cable.
•
An external archive device, such as a DVSe, RAID, CD-R, DAT, or AIT drive.
•
Printer with Printer Server connected via ethernet cable.
For instructions regarding the connection of the associated security equipment in your system, please
consult the instruction manual of the associated equipment.
1.7 The Back Panel
1
2
3
4
5
6
AUX
7
8
RS-485/1
ETHERNET
10/100
RS-485/2
RS-232/2
14
15
12V DC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SVHS
RS-232/1
SCSI
B
IEEE-1394
B
9
10
11
12
13
1. Camera Inputs: BNC connector, looping. Auto Terminating.
2. Composite Monitor-A Output: Composite video output with BNC style connector.
3. Y/C Monitor-A Output: Y/C video output with 4-pin mini-DIN style connector.
4. Alarm I/O: For connecting alarm inputs, and alarm output relays.
5. Power Input: For connecting the power supply.
6. Aux Port: For connecting the Accessory PCB for Audio inputs and outputs.
7. RS485 Port 1 Connector: For connecting to keyboard and other RS485 devices.
8. 10/100 Ethernet Port: For connecting to remote PC via ethernet network.
9. Composite Monitor-B Output: Composite video output with BNC style connector.
10. Y/C Monitor-B Output: Y/C video output with 4-pin mini-DIN style connector.
11. SCSI Port: For connecting SCSI compatible archive devices.
12. IEEE 1394 Firewire Port: For connecting Firewire compatible archive devices
13. RS232 Port 1: For modem connection and external control of the unit.
14. RS485 Port 2 Connector: For connecting to keyboard and other RS485 devices.
15. RS232 Port 2: For Event Generation and ASCII Text insertion.
0150-0193F
10
Kalatel DVMRe Triplex
Camera Inputs
There are two BNC jacks for each camera. Either
jack can receive a camera signal. The signal is
looped (directly connected to the other jack), making
the camera signal available to other equipment.
Cable: 75-Ohm Coaxial
The camera input connectors are Auto Terminating.
Passive Looping: Yes
Connectors: BNC
Auto Terminating: Yes
This means that the input signal will automatically be terminated with 75-Ohms unless a 2nd cable is
connected to the 2nd BNC connector of the same camera input. Make sure there is 75-Ohm
termination at the end of the video line if the signal is looped through the DVMRe Triplex.
Time base correction is performed during digital capture. As a result, cameras do not require
synchronization.
See section 3.14 for information about disabling unused camera jacks in the menu system.
Composite Monitor Output
When connecting directly from the DVMRe Triplex to
the monitor, select the 75-Ohm impedance setting on
the monitor.
Cable: 75-Ohm Coaxial
Connectors: BNC
If an additional device is connected to the monitor’s looping output, set the termination of the additional
device as 75-Ohm, and set the termination of the monitor as Hi-Z (High Impedance).
Y/C Monitor Output
Y/C video output has a 4-pin mini-DIN style
connector. This style of connection is also referred to
as SVHS and S-Video.
Cable: 75-Ohm Coaxial
Connectors: BNC
Alarm I/O Port
The back panel of the unit is equipped with an Alarm
Port (DB-25 style connector).
Do not attempt to wire directly to the DB-25
connector on the back panel.
DB-25 Connector on Back Panel
Connect the Alarm PCB (supplied with the unit) to the Alarm Port. Wire all alarm inputs to the Alarm
PCB per the pin out specifications shown below.
0150-0193F
11
Kalatel DVMRe Triplex
Pin 14: Alarm Input 14.
Pin 3: Alarm Input 3.
Pin 15: Alarm Input 15.
Pin 4: Alarm Input 4.
Pin 16: Alarm Input 16.
Pin 5: Alarm Input 5.
Pin 17: Alarm Output Relay #1.
Pin 6: Alarm Input 6.
Pin 18: Ground.
Pin 7: Alarm Input 7.
Pin 19: Ground.
Pin 8: Alarm Input 8.
Pin 20: Ground.
Pin 9: Alarm Input 9.
Pin 21: Alarm Output Relay #1 Common.
Pin 10: Alarm Input 10.
Pin 22: Alarm Output Relay #2.
Pin 11: Alarm Input 11.
Pin 23: External Alarm Silence and Acknowledge Input.
Pin 12: Alarm Input 12.
Pin 25: Alarm Output Relay #2 Common.
14
A14
2
A2
15
A15
3
A3
16
A16
4
17
A4 NO1
5
18
6
19
7
A5 GND A6 GND A7
A9 COM1 A8 GND GND
9
21
8
20
20
Pin 2: Alarm Input 2.
Signal A13 COM2 A12 Vext A11 ACK A10 NO2
PIN 13
25
12
24
11
23
10
22
Pin 13: Alarm Input 13.
PIN
1
Signal A1
Pin 1: Alarm Input 1.
Alarm PCB
Active alarm inputs vary by DVMRe model. 4 channel units (4CT) have 4 active alarm inputs. 10
channel units (10CT) have 10 active alarm inputs.
Alarm Input
An alarm condition can be activated by devices such as pressure pads, passive infrared detectors,
door switches, or other similar devices.
See section 3.11 for information about configuring the contacts as Normally Open or Normally Closed
in the menu system.
Normally Open, Zero Potential Relay Contact: Configure in menu as Normally Open.
Normally Closed, Zero Potential Relay Contact: Configure in menu as Normally Closed
TTL Active High: Configure in menu as Normally Closed.
High: 5V (12V Tolerant)
TTL Active Low: Configure in menu as Normally Open.
Low: Ground
Open Collector Active On: Configure in menu as Normally Open.
Inputs: 1 per channel.
Open Collector Active Off: Configure in menu as Normally Closed.
DVMRe Triplex DB25 Connector
Alarm Input No. 1
pin 1
Alarm Input No. 2 - 15
Normally Open
(Closes During Alarm)
pins 2-15
Typical Alarm Device
Alarm Input No. 16
Ground
pin 16
Refer to each alarm device's manual for specific wiring details.
pins 18-20
Normally Closed
(Opens During Alarm)
Typical wiring for Alarm #1 as Normally
Open and Alarm #16 as Normally Closed.
Typical Alarm Device
Normally Open and Normally Closed Connections
0150-0193F
12
Kalatel DVMRe Triplex
Alarm Relay Output
The alarm relay output is activated when an alarm condition
exists. The alarm output is only active for the duration of the
alarm.
Output: Zero potential relay contacts,
programmable in menu system as
Normally Open or Normally Closed.
Alarm relays can be programmed in the menu system to
respond to macros, and video loss. See section 3.11 for
information about configuring the alarms in the menu system.
Voltage: 30V (Max)
Current: 500mA (Max)
Typical wiring for Alarm Relays. Relays may be
programmed Normally Open or Normally Closed.
pin 17
Alarm
Device
Output Relay No. 1
Power
Source
pin 21
pin 22
Output Relay No. 2
Power
Source
Controlled
Device
pin 25
DVMRe Triplex DB25 Connector
External Alarm Acknowledge Input
Connect a switch or similar device to ground this pin in order
to acknowledge an alarm condition, and silence associated
buzzers and relays. Connect from pin 23 to either pin 18, 19,
or 20 (ground pins).
NOTE
External Device: Normally Open
Zero potential relay contact.
All specifications subject to change without notice. GE-Interlogix believes all specifications
to be correct at time of printing, but no liability is assumed for omissions or errors.
AUX Port
The back panel of the unit is equipped with an Aux Port
(DB-9 style connector).
Do not attempt to wire directly to the DB-9
connector on the back panel.
1
6
5
9
DB-9 Connector on Back Panel
Connect the Accessory PCB (supplied with the audio equipped models) to the AUX port to access the
Audio features. Wire the audio input and output to the Accessory PCB per the pin out specifications
shown below.
0150-0193F
13
Kalatel DVMRe Triplex
Pin 1: Not Used.
Pin 2: Audio Out.
Pin 3: Ground.
Pin 4: Audio In.
Pin 5: Ground.
Pin 6: Not Used.
Pin 7: Ground.
Pin 8: Not Used.
1
6
2
7
3
8
4
9
5 GND
Pin 9: Ground.
Accessory PCB
GND: Ground.
RS485 Connector
Shields are grounded at one end, preferably at the
DVMRe Triplex.
Wire Type: #24 AWG, twisted pair with shield
(2-wire)
See section 3.17 for information about configuring
the RS485 network address settings in the menu
system.
Connector Type: RJ-45
Max. Cable Length: 3200 feet / 1000 meters
RJ-45 Pin Configuration For RS485 Port
Pin
Use
Pin
Use
1
Ground (Shield)
5
Not Connected
2
Not Connected
6
Network -VE
3
Network +VE
7
Ground (Shield)
4
Not Connected
8
Not Connected
1 2 3 4 5 6 7 8
RJ-45 socket on
back panel.
Ethernet Port
The cable connection configuration depends on your
network configuration:
•
For a DVMRe Triplex that connects directly to a
Hub or Switch, use a straight through connection.
•
For a DVMRe Triplex that connects directly to a
PC, use a cross over connection.
Consult with your MIS personnel for the specific type
of configuration. See section 3.17 for information
about configuring the ethernet settings in the menu
system.
0150-0193F
14
Wire Type: Cat 5
Connector Type: RJ-45
Max. Cable Length: 100 meters / 328 ft.
Min. Cable Length: 6 feet / 1.8 meters
Hub Wiring Configuration: Straight Through
PC Wiring Configuration: Cross Over
Kalatel DVMRe Triplex
RJ-45 Pin Configuration For Ethernet Port
Pin
Use
Pin
Use
1
TX+
5
Not Connected
2
TX-
6
RX-
3
RX+
7
Not Connected
4
Not Connected
8
Not Connected
NOTE
1 2 3 4 5 6 7 8
RJ-45 socket on
back panel.
SCSI and IEEE 1394 archiving devices should not be connected to the Kalatel DVMRe
Triplex simultaneously. Archiving support is only available for one or the other type of
interface at a time.
SCSI Port
The unit is equipped with a SCSI port for
connecting external archive devices. The unit only
supports a single SCSI device. The SCSI ID of the
archive device must be set to 0.
The SCSI bus must be terminated, otherwise the
system will not operate properly.
Connector: 50 Pin, High Density SCSI-2.
Gender (on unit) : Female
Compatible devices : DVSe, RAID, DAT, AIT,
CD-R, CD-RW
SCSI ID : 0
Additional menu setup may be necessary to
configure archive device. See section 3.15.
IEEE 1394 Firewire Port
The unit is equipped with an IEEE 1394 Firewire port
for connecting Firewire compatible external archive
devices. For information on the approved devices,
please refer to the Archiving Addendum manual that
is supplied with this unit.
0150-0193F
15
Cable: 6 position Firewire
Connectors: 6 position DIP
Kalatel DVMRe Triplex
RS232 Port 1
For a Modem connection or remote control of unit. See section 3.17 for information about configuring
the modem settings in the menu system. See section 9 for RS232 Remote Control Protocols.
DB-9 Pin Configuration For Port 1
1
Pin
Use
Pin
Use
Pin
Use
1
DCD
4
DTR
7
RTS
2
RX
5
Ground
8
CTS
3
TX
6
Not Connected
9
Not Connected
6
For Event Generation and ASCII Text Insertion.
RJ-45 Pin Configuration For RS232 Port 2
Use
Pin
Use
1
Ground
5
TXD
2
Reserved
6
Not Connected
3
Not Connected
7
Ground
4
RXD
8
Reserved
1 2 3 4 5 6 7 8
RJ-45 socket on
back panel.
1.8 Power-Up
It is important that the power-up procedures be followed carefully. The unit uses its auto-detect
feature to detect camera signals during power-up, and configure itself automatically.
Power-up procedure
Once the system installation is complete, apply
power in the following order:
1. Energize the monitors and all of the cameras.
2. Energize the DVMRe Triplex.
Power Supply Input
Voltage: 12 Volt DC
Power: 60 Watt (5 Amp)
Connector: 2.1mm barrel, center positive
Once power is applied to the unit, it will begin its power-up procedure. The unit will begin by displaying
the software version on Monitor-A, then the unit will begin recording automatically.
Check Video Input Quality
Check the picture quality by selecting each camera for full screen display. If the picture quality is poor,
check the following items:
•
The BNC connections.
•
The loop-through terminations.
•
The video levels of incoming signals.
•
The possibility of ground loops.
•
Consult the camera’s installation instructions for additional information about proper camera setup.
0150-0193F
16
9
DB-9 on back panel.
RS232 Port 2
Pin
5
Kalatel DVMRe Triplex
Check Record And Playback Quality
Record for at least three minutes at the default record rate. Then play back the recording, selecting
each camera for full screen display. Check the playback picture quality.
1.9 Minimum Recommended Menu Setup
After installation is complete, it is strongly recommended that, as a minimum, the items in the
QuickInstall menu be configured before the unit is used. All the features located in the QuickInstall
menu are also found in the Main menu. These items are provided in the separate QuickInstall menu
as a convenience for the installer.
For information about accessing and configuring the menu system, see Section 3.
To find detailed information in this manual about configuring each item in the QuickInstall menu, use
the following table to locate the main menu location of each item in the QuickInstall menu.
QuickInstall
Menu Item
Main Menu Location
Section in
Manual
Change the time
Main Menu → Time/Date → Set Time
3.8
Change the date
Main Menu → Time/Date → Set Date
3.8
Edit Camera
Titles
Main Menu → Camera Setup → Camera Titles → Edit Titles
3.14
Camera Disable
Main Menu → Camera Setup → Camera Disable
3.14
Record Quality
Main Menu → Record → Record Quality
3.10
Installer
Password
Main Menu → Passwords → Installer Password
3.20
Auto Disable
Now
Main Menu → Camera Setup → Camera Disable → Auto
Disable Now
3.14
0150-0193F
17
Kalatel DVMRe Triplex
2 DMVRe Triplex Basic Operations
2.1 Principal Operating Modes
The DVMRe Triplex has three principal modes of operation:
• Live Viewing.
•
Playback.
• Recording.
All three of these modes can operate simultaneously. Each mode is discussed in detail later in this
section.
2.2 The Front Panel
1
2
3
4
5
6
7
8
9
e
A
B
{F}
Kalatel DVMRe Triplex
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
11 12 13 14
15 16 17
18
1. Multiscreen Selection Buttons: 16, 10, 7, and 4 way.
2. Monitor Selection Button: Monitor A or Monitor B.
3. Multiscreen Selection Buttons: 13, 9, 6 way, and Picture-in-Picture.
4. Camera Selection Number buttons: Camera numbers 1 through 16.
5. Reverse Play Button: Playback in Reverse.
6. Freeze Button: Freezes camera images on-screen in Live mode. Pauses Playback.
7. Play Forward Button: Begins Playback.
8. Jog/Shuttle: Controls Playback speed and Menu selections.
9. Menu Button: Provides access to on-screen menus.
10. Power Indicator: Indicates power on/off condition.
11. Alarm button: Allows user to acknowledge and silence alarms.
12. Sequence Button: Sequences camera views.
13. Zoom Button: Provides a 2X digital zoom.
14. Function Button: Used in conjunction with Camera Buttons to run Macros.
15. Record Button: Used to Start and Stop Recording.
16. Stop Button: To stop Playback and return to Live mode.
17. Search Button: Access to stored video data.
18. Enter Button: Confirms selection in menus.
0150-0193F
18
Kalatel DVMRe Triplex
2.3 Live Viewing
Multiscreen Display
In Live Multiscreen mode, press one of the Multiscreen buttons to activate
the multiscreen display on Monitor-A or Monitor-B. Live Multiscreens are
displayed with gray borders. For detailed information about Multiscreen
displays, see section 2.6.
A
B
Multiscreen Buttons
Multiscreen Display With Sequencing
If a multiscreen display does not include all of the cameras, the remaining
cameras can be sequenced in the bottom right cameo. While in a multiscreen
display, press the Sequence button to begin sequencing. For detailed
information about sequencing, see section 2.8.
Sequence Button
Full Screen Display
Select any camera for Full Screen display by pressing the Number button of
the desired camera. Pressing the Camera number button again displays the
Status Display Box. Pressing the same button a third time displays any
associated ATM or cash register ASCII text, see section 2.9.
1
Number Button
Sequenced Full Screen Display
While in a Full Screen display, press the Sequence button to begin full
screen sequencing. The sequence list and dwell times are programmable.
For detailed information about programming the sequence list see section
2.8. For detailed information about configuring the dwell times in the menu
system, see section 0.
Sequence Button
Zooming
To activate the 2x digital zoom, select the full screen display of the camera
you wish to zoom, then press the Zoom button. Zooming will be indicated by
the LED located directly above the Zoom button. Zooming is also indicated
as ZOOM on the primary monitor. Zooming works with frozen and non-frozen
images. Zoomed images can also be frozen.
While Zoomed, rotate the Jog/Shuttle to Pan and Tilt across the image.
Please note, the camera does not move during digital Pan/Tilt.
Zoom Button
with LED
Press the Zoom button again to cancel the Zoom operations.
NOTE
If the Zoom button is pressed while in a multiscreen display, the camera from the last active
cameo is selected for full screen display. Press the Zoom button again to activate the Zoom
operation.
Freezing
Pressing the Freeze button freezes all camera images on-screen. Full
Screen freezing is indicated as FRZ on-screen. Multiscreen freezing is
indicated as * (a flashing asterisk) in each frozen cameo.
Individual cameos can be frozen in Active Cameo mode (see section 2.7).
Freeze Button
Press the Freeze button again or any camera button to cancel Freeze
operations.
0150-0193F
19
Kalatel DVMRe Triplex
Selecting Monitor-B
To control Monitor-B, press the lower part of the Monitor button. The
Monitor-B LED will light to indicate that the number keypad now controls
Monitor-B. Press the upper part of the Monitor button again to return the
keypad control to Monitor-A.
A
B
Monitor Button
2.4 Playback
Playback always displays on Monitor A. Playback multiscreen borders are black, as opposed to the
gray borders of the live multiscreens. Monitor B continues to display full or multiscreen live images in
playback mode. To begin playback, press the Play Forward or Reverse Play button.
Play Forward
When the Play Forward button is pressed, the unit will play forward at the rate
the data was recorded. While in Playback mode, the user may change the
playback direction, playback speed, etc. To return to Play Forward operations,
press the Play Forward button.
Play Forward
Button
Reverse Play
To begin reverse playback, press the Reverse Play button.
Reverse Play
Button
Fast Forward
During playback, rotate the Shuttle (the outer dial) clockwise to view data at a
higher than normal rate. Increasing the amount of rotation increases the rate of
playback.
Jog / Shuttle
AutoPause
During playback, moving the Jog (the inner dial) in any direction will freeze
playback. Depress the Freeze or any Play button to continue playback.
Rewind
During playback, rotate the Shuttle counter-clockwise to view data (in reverse) at
a higher than normal rate. Increasing the amount of rotation increases the rate of
playback.
Freeze
During playback, press the Freeze button. This feature pauses all full screen and
multiscreen images
Freeze Button
Single Frame Advance & Single Frame Rewind
During Freeze or Pause mode, rotate the Jog (the inner dial) to view the frame
directly before or after the frame displayed on-screen.
0150-0193F
20
Kalatel DVMRe Triplex
Stop Playback
To stop playback and return to Live Multiscreen mode on Monitor A, press the
Stop button.
Stop Button
Multiscreen Display
During Playback, press one of the Multiscreen buttons to activate a
multiscreen display. The 6-way and PIP multiscreen displays are not
available in Playback mode. For detailed information about Multiscreen
displays, see section 2.6.
A
B
Multiscreen Buttons
Multiscreen Display With Sequencing
If a multiscreen display does not include all of the cameras, the remaining
cameras can be sequenced in the bottom right cameo. While in a multiscreen
display, press the Sequence button to begin sequencing. For detailed
information about sequencing, see section 2.8.
Sequence Button
Full Screen Display
Select any camera for Full Screen display by pressing the Number button of
the desired camera. Pressing the Camera number button again displays the
Status Display Box. Pressing the same button a third time displays any
associated ATM or cash register ASCII text.
1
Number Button
Sequenced Full Screen Display
While in a Full Screen display, press the Sequence button to begin full
screen sequencing. The sequence list and dwell times are programmable.
For detailed information about programming the sequence list see section
2.8. For detailed information about configuring the dwell times in the menu
system, see section 0.
Sequence Button
Zooming
To activate the 2x digital zoom, select the full screen display of the camera
you wish to zoom, then press the Zoom button. Zooming will be indicated by
the LED located directly above the Zoom button. Zooming is also indicated
as ZOOM on the monitor. Zooming works with frozen and non-frozen
images. Zoomed images can also be frozen.
While Zoomed, use the Jog/Shuttle to Pan and Tilt across the image.
Please note, the camera does not move during digital Pan/Tilt.
Zoom Button
with LED
Press the Zoom button again, or another camera button to cancel the Zoom
operations.
If the Zoom button is pressed while in a multiscreen display, the camera from the last active
cameo is selected for full screen display. Press the Zoom button again to activate the Zoom
operation.
Searching Recorded Data
The DVMRe Triplex has a powerful search interface feature that allows the user to search for data on
the internal hard disk or an external archive device. The user may search the data for previous
recording sessions, text insertion, alarm conditions, or for motion in a selectable area of the scene.
0150-0193F
21
Kalatel DVMRe Triplex
Because the search interface is so dynamic, the search interface is covered in detail in a separate
section of this manual. See section 5.
2.5 Recording
To begin recording, press the Record button. Recording will be indicated by the
LED located directly above the Record button. The unit always starts recording
at the end of previously recorded data.
The unit will continue recording until the record button is pressed again.
Record Button
Monitor Displays During Recording
Multiscreen Live and Playback displays on Monitor A and Monitor B are not affected by recording
operations.
Monitor A
0150-0193F
Monitor B
LIVE
LIVE
or
LIVE
PLAY
BACK
LIVE
or
LIVE
LIVE
PLAY
BACK
LIVE
22
Kalatel DVMRe Triplex
2.6 Display Options
Available Multiscreen Displays
Press the Multiscreen buttons to activate the multiscreen display. Pressing the individual multiscreen
button will display the corresponding multiscreen.
10-Way
9-Way
Monitor A
7-Way
6-Way
AA
16-Way
13-Way
BB
Monitor B
4-Way
PIP
The multiscreen display is limited to the number of camera inputs on the unit.
Sixteen-Channel unit: Capable of displaying all multiscreens.
Ten-Channel unit: Only capable of displaying 10-way through 4-way multiscreen and PIP.
Four-Channel unit: Only capable of displaying 4-way multiscreen and PIP.
The camera assignments for each multiscreen is retained (in non-volatile memory) for both Live and
Playback multiscreen mode on Monitor A, as well as Live multiscreen mode on Monitor B.
PIP: Use the Jog/Shuttle to adjust the location and size of the PIP display. Please note that the PIP
display is only available on Monitor A in Live mode, when Monitor B is in fullscreen display mode.
2.7 Active Cameos
A cameo is defined as any cell within a multiscreen display. Active Cameo mode allows the user to
access and edit each cameo individually.
Entering Active Cameo Mode
While viewing a multiscreen, enter Active Cameo mode by pressing the Enter
button. Active Cameo mode is indicated on-screen by flashing the number
and titles of the active cameo and the LED above the Enter button is lit. By
default, the top left cameo is activated.
Enter Button
Selecting Cameos
Select a cameo using the Jog/Shuttle to navigate the multiscreen. Rotating
the Jog selects the next screen up or down a row. Rotating the shuttle
selects the next screen in numerical order. The active cameo will always be
indicated by the flashing camera number and titles.
Jog/Shuttle
0150-0193F
23
Kalatel DVMRe Triplex
Selecting Cameras
Display any camera in the active cameo by pressing the Number button of
the desired camera. Once a camera has been selected, the active cameo
advances to the next cameo on the right.
1
Number Button
The camera selection only changes the multiscreen currently being displayed. Each multiscreen must
be configured separately. Changes to the multiscreen display are saved in non-volatile memory, and
will be retained even if power is removed from the unit.
Freezing
Press the Freeze button to freeze the image in the selected cameo. Each
frozen cameo is indicated as * (a flashing asterisk) on-screen.
Press the Freeze button again to cancel Freeze operations.
Freeze Button
2.8 Sequencing
The sequencing feature allows a camera to be displayed briefly on-screen,
before advancing to the next camera in the sequence list. The default
sequence list displays each camera in numerical order.
Sequence Button
Dwell Time
The dwell time is the amount of time each camera is displayed on-screen before advancing to the next
camera. The Full Screen and Multiscreen Dwell Times are separately programmable in the menu
system. For detailed information about configuring the dwell times in the menu system, see section 0.
Autolist™ Custom Sequence List
The Autolist™ feature allows the user to create a custom sequence list, controlling the order the
cameras are displayed and the dwell time. Separate Autolists may be created for Monitor A (Live and
Playback mode) and Monitor B (Live mode). Using the Monitor button, select the monitor to be
programmed. Then, using a Number button, select any camera for full screen display.
NOTE
The unit must be in Full Screen Display mode before starting to create the sequence list.
This initial camera is not part the sequence list.
To begin recording the Autolist™ sequence: Press the Alarm button and
Sequence button simultaneously. Autolist Program mode is indicated as
PGM on-screen.
Recording starts when the first camera number is pressed. Press the camera
numbers in the order you wish them to appear on-screen. The amount of
time between button presses determines the Dwell Time. During sequence
list programming, pressing any button other than a Number button or the
Sequence button voids the sequence list.
Alarm Button and
Sequence Button
To end the recording: Press the Sequence button. The amount of time between pressing the last
Number button and the Sequence button determines the dwell time for the final camera in the
sequence list.
Returning To The Default Sequence List
The default sequence list is all cameras in numeric order with a three second dwell time.
0150-0193F
24
Kalatel DVMRe Triplex
To return the unit to the default sequence list, go to the Main Menu → Sequencing → Full Screen
Dwell menu. Select 03 seconds by rotating the Jog, then press the Enter button.
Note: Any alteration of the dwell time from this menu will cancel the sequence list and return to the
default (numeric) order.
Sequencing In Cameos
While viewing a multiscreen display, additional cameras (cameras not shown in the multiscreen
display) can be sequenced in the lower right hand cameo by pressing the Sequence button. The
sequence list is not programmable, but the dwell time can be adjusted in the menu system. Press the
Sequence button again to cancel sequencing.
2.9 On-screen Indicators
There are five types of on-screen indicators.
Camera Titles: Displays the camera number and the camera title.
Status Indicators: Displays Time, Date, and Hard Disk record time left.
Conditional Indicators: Displays indicators for Freeze, Zoom, Alarm, Motion Detection, Videoloss,
Autolist™ Program mode, Macro Record and Macro Playback mode.
Status Display Box: Displays Archive Device, Network status and Image Quality Setting (Playback
mode only).
Text Display Box: Displays ATM/POS Text data.
Camera Titles
Camera Titles are displayed on either the upper or lower corner of the left hand side of the screen.
The camera title can be changed in the menu system (see section 3.14). The user can change display
position and color. See below.
Changing Position And Color Of Title And Status Indicators
Camera Titles: To change the color and position of the camera
titles, select a camera for full screen display, then press the Enter
button to advance to the next display setting. Repeatedly pressing
the Enter button advances the display settings through the
sequence show in the table on the right.
Example: Select Camera 1 for full screen display. Using the
Enter button, cycle through the sequence shown on the right.
Each time the position cycle is completed, the unit advances the
Status Indicator color. Choose Black, White or Gray.
Position
Color
Top Left
Black
Top Left
White
Top Left
Gray
Bottom Left
Black
Bottom Left
White
Bottom Left
Gray
Title not displayed
Status Indicators
Status indicators are displayed on the upper right hand corner of the
screen.
Status indicators include:
•
Time and Date (these can be turned off in the menu system, see
section 3.8). The Time and Date format can also be changed in
the menu system.
•
Time remaining on Hard Disk(s).
0150-0193F
25
Small Cameo
Kalatel DVMRe Triplex
Conditional Indicators
Condition
Full Screen Indicator
Multiscreen Indicator
Alarm
ALM
A in cameo of camera in alarm
Autolist™ Program
mode
PGM
PGM
Freeze
FRZ
* (Asterisk) in frozen cameo
Macro Record mode
F followed by macro number
F followed by macro number
Motion Detection
M
M in cameo w/ motion detection
Videoloss
VDL
V in cameo with videoloss
Zoom
ZOOM
ZOOM
Status Display Box
A Status Display Box can be viewed by pressing the Camera Number button twice. Status Indicators
include:
On Live Fullscreen:
•
•
Archive Status: Not Connected, Not Ready, Ready, Ejecting, Play, and timeleft. Timeleft
indicates the amount of time before the archive medium is full (Only available if the unit has
Background Archiving turned On).
Network: Displays all current Network connections. Normal connection is displayed as ip.ip or --if there is no connection. Live connections are displayed as E1: ip.ip, E2: ip.ip, etc. (where ip.ip
represents the last 2 bytes of the IP Address). POTS connection is displayed as IP 1.1.
On Playback Fullscreen:
•
All the above, including Image Quality Setting: High, Medium, Standard.
ATM/POS Text Display
Pressing the Camera Number a third time displays an ATM/POS text display. This feature can be
used during live viewing mode to verify that the DVMRe Triplex is receiving ATM/POS text, or in
Playback mode to review recorded text and video.
2.10 Triplex Mode
Triplex mode allows the display of both live and playback images to appear on Monitor A
simultaneously. Live images have gray borders, while playback images have black borders.
To enter Triplex mode, press the Play Forward button while in Play Forward mode. Alternatively, press
the Play Reverse button while in Play Reverse mode. Both the Play Forward LED and the Stop LED
turn on to indicate that the unit is in Triplex mode.
Monitor B always switches to a fullscreen live display whenever Triplex mode is entered.
Play Forward
When in Play Forward mode and the Play Forward button is pressed, the unit will
enter the Triplex mode of operation. When Play Forward is pressed again, the
unit will revert back into the normal Playback mode. While in the Triplex mode, if
reverse play is in progress, the Play Forward button will change the playback
direction.
0150-0193F
26
Play Forward
Button
Kalatel DVMRe Triplex
Reverse Play
When in Reverse Play mode and the Reverse Play button is pressed, the unit will
enter the Triplex mode of operation. When Reverse Play is pressed again, the
unit will revert back into the normal Playback mode. While in the Triplex mode, if
forward play is in progress, the Reverse Play button will change the playback
direction.
Reverse Play
Button
Fast Forward
During Triplex mode, rotate the Shuttle (the outer dial) clockwise to view
playback images at a higher than normal rate. Increasing the amount of rotation
increases the rate of playback. Live images are not affected.
Jog / Shuttle
Rewind
During Triplex mode, rotate the Shuttle counter-clockwise to view playback
images (in reverse) at a higher than normal rate. Increasing the amount of
rotation increases the rate of playback. Live images are not affected.
Freeze
During Triplex mode, pressing the Freeze button pauses all multiscreen images,
both Live and Playback.
Freeze Button
Single Frame Advance & Single Frame Rewind
During Freeze or Pause mode, rotate the Jog (the inner dial) to view the frame
directly before or after the frame displayed on-screen. Only the playback images
are affected.
Stop
To stop Triplex mode and return to Live mode on Monitor A, press the Stop
button.
Stop Button
Multiscreen Display
During Triplex mode, press one of the Multiscreen buttons to activate a
multiscreen display. The 6-way and PIP multiscreen displays are not
available in Triplex mode. For detailed information about Multiscreen
displays, see section 2.6. The Live and Playback images in a multiscreen
display may be transposed by pressing the multiscreen button that
corresponds with the current multiscreen display.
A
B
Multiscreen Buttons
E.g. If the current display is a 13-way multiscreen with the center cameo being a playback image and
the rest of the cameos being live images, pressing the 13-way multiscreen button will result in the
center cameo being live and the rest of the cameos being playback images.
0150-0193F
27
Kalatel DVMRe Triplex
Multiscreen Display With Sequencing
The bottom right cameo of any multiscreen will start sequencing when the
Sequence button is pressed. If this camera is a playback image, the
sequencing will include all the non-displayed playback cameras, and vice
versa for a live image.
Sequence Button
Full Screen Display
Select any camera for Full Screen display by pressing the Number button of
the desired camera. Pressing the Camera number button again displays the
Status Display Box. Pressing the same button a third time displays any
associated ATM or cash register ASCII text.
1
Number Button
Sequenced Full Screen Display
While in a Full Screen display, press the Sequence button to begin full
screen sequencing. The sequence list and dwell times are programmable.
For detailed information about programming the sequence list see section
2.8. For detailed information about configuring the dwell times in the menu
system, see section 0.
Sequence Button
Zooming
To activate the 2x digital zoom, select the full screen display of the camera
you wish to zoom, then press the Zoom button. Zooming will be indicated by
the LED located directly above the Zoom button. Zooming is also indicated
as ZOOM on the monitor. Zooming works with frozen and non-frozen
images. Zoomed images can also be frozen.
While Zoomed, use the Jog/Shuttle to Pan and Tilt across the image.
Please note, the camera does not move during digital Pan/Tilt.
Zoom Button
with LED
Press the Zoom button again, or another camera button to cancel the Zoom
operations.
NOTE
If the Zoom button is pressed while in a multiscreen display, the camera from the last active
cameo is selected for full screen display. Press the Zoom button again to activate the Zoom
operation.
2.11 The Print Image Feature
Pressing the Function and Zoom button will print the currently displayed
image. If any multiscreen is the display mode, the Triplex will switch to a
single image display of the last selected fullscreen camera, freeze the image,
and send to the default printer.
0150-0193F
28
{F}
Zoom and Function
Button
Kalatel DVMRe Triplex
Printer Setup
The following equipment and conditions are required for the operation of the Print Image feature.
Equipment
HP DeskJet 3820
Hawking Print Server PN7127P
Conditions
The Printer and Print Server must be connected to the same local network as the Triplex.
The Triplex must be aware of the Print Server’s IP address. The IP address can be input under Main
Menu – Communications – Ethernet – Ethernet Settings (See Section 3.15).
The Printer and Print Server must be On-line and Operational.
0150-0193F
29
Kalatel DVMRe Triplex
3 Menu System Overview
3.1 Menu Notation In This Manual
In the following sections, there are headings like this:
q
Main Menu → Time/Date → Set Time
Meaning: From the Main Menu, select Time/Date, then press the Enter button. The Time/Date menu
will appear. From the Time/Date menu, select Set Time, then press the Enter button. A pop-up or
pull-down menu will appear.
Selected Items
Items selected in the menu system are represented in the manual as follows:
Selected
Not Selected
Time/Date
Time/Date
3.2 Accessing The Menu System
Enter the menu system by pressing the Menu button. A Password Box will appear
on the primary monitor. Enter either the:
•
Operator Password: Providing limited access to the menu system. Only the
Operator and System View menus are available.
•
Installer Password: Providing complete menu access.
Menu Button
Use the Number buttons to enter the appropriate password.
Default passwords are provided in the beginning of this manual, in section 1.
3.3 Available Menus
Main
QuickInstall
Operator
SystemView
Time/Date
Change the time
Sequencing
About DVMR
Sequencing
Change the date
Time/Date Display
View Screen 1
Record
Edit Camera Titles
Titles Display
View Screen 2
Alarms
Camera Disable
Alarm History
View Screen 3
Macro
Record Quality
Archive Setup
View Screen 4
Motion Detection
Installer Password
Operator Password
View Screen 5
Camera Setup
Auto Disable Now
View Screen 6
Archive Setup
View Screen 7
Audio Setup
View Screen 8
Communications
View Screen 9
Front Panel Lock
Factory Settings
Passwords
0150-0193F
30
Kalatel DVMRe Triplex
3.4 Menus In This Manual
Each menu is covered in detail in this chapter of this manual. Menus and Menu Items appear in the
manual in the same order they appear on-screen.
•
Main Menu
•
QuickInstall Menu
•
Operator menu
•
SystemView Menus
3.5 Navigating The Menu System
Selecting a Menu from the Menu Bar: When the menu system is first accessed, only the menu bar
is displayed. Use the Shuttle to select the desired menu.
Opening the Drop Down Menus: Rotate the Jog.
Navigating in Menus: Rotate the Jog to highlight items in the drop-down menus.
Selecting Menu Items: Hit the ENTER button to select the highlighted menu item.
Exiting Menus: Press the Menu button to exit a menu. From the menu bar, press the Menu button
to exit the menu system completely.
Shuttle
Main
QuickInstall
Operator
SystemView
Time/Date
Sequencing
Record
Jog
Alarms
Motion Detection
Camera Setup
Archive Setup
Audio Setup
Jog
Macro
Shuttle
Communications
Front Panel Lock
Factory Settings
Passwords
3.6 Menu Shortcuts
Zoom Button:
In menu lists that have 2 settings per camera, the Zoom button will toggle all
selections. This provides a quick and easy way to enable or disable all cameras
for a particular feature.
Camera Button:
In menu lists that provide settings per camera, a particular camera may be
accessed directly by pressing on the associated camera button. Rotate the
Shuttle to modify the setting.
0150-0193F
31
Kalatel DVMRe Triplex
3.7 The Main Menu
Main Menu Overview
The Main menu contains the majority of programmable options for the DVMRe Triplex. Each item in the
Main menu is described in detail in this section of the manual.
Main menu items appear in this section in the same order they appear in the menu.
3.8 Time/Date
Use this menu to specify:
Time/Date Display
•
Which monitors will display the time and date.
Set Time Format
•
The time format: 12 or 24 hours.
Set Date Format
•
The date format: MM/DD/YY, YY/MM/DD, or DD/MM/YY.
Set Time
•
The time and date.
•
Whether the unit’s clock is a master or slave.
•
Set Regional Daylight Savings Time.
•
Setup clock synchronization between Triplex and Network Server.
q
Set Date
Set Master/Slave
Set Region
Network Time Setup
Main Menu → Time/Date → Time / Date Display
Use this menu to specify if the time and date will be displayed on:
Time/Date Display
•
Monitor-A.
Monitor A : ON
•
Monitor-B.
Monitor B : ON
•
Both Monitors.
•
Not Displayed
[CANCEL]
[OK]
Rotate the Jog to navigate, then rotate the Shuttle to change the values.
Save changes and exit the menu: Select [OK], then press the Enter button.
Exit the menu without making changes: Press the Menu button, or select [CANCEL], then press
the Enter button.
q
Main Menu → Time/Date → Set Time Format
Rotate the Jog to set the desired time format. Select from either:
Time Format Setup
•
12 Hour
Select Format
•
24 Hour
12 HOUR
Press the Enter button to confirm the selection and exit the menu.
Press the Menu button to exit the menu without making changes.
0150-0193F
32
Kalatel DVMRe Triplex
q
Main Menu → Time/Date → Set Date Format
Rotate the Jog to set the desired date format. Select from either:
•
MM/DD/YY
•
DD/MM/YY
•
YY/MM/DD
Date Format Setup
Select Format
MM/DD/YY
Press the Enter button to confirm the selection and exit the menu.
Press the Menu button to exit the menu without making changes.
q
Main Menu → Time/Date → Set Time
1. Rotate the Shuttle to navigate, highlight HH MM SS.
2. Press the Enter button, the highlighting will move to the row of numbers.
3. Enter the time in Hours, Minutes, and Seconds. Rotate the Jog to
change the values and the Shuttle to navigate.
Time Setup
HH MM SS
03 05 53
4. Press the Enter button to confirm the selection and exit the edit mode.
[CANCEL]
[OK]
5. To save the changes and exit the menu: Rotate the Jog to select [OK],
then press the Enter button.
6. To exit the menu without making changes: Rotate the Jog to select
[CANCEL], then press the Enter button.
q
Main Menu → Time/Date → Set Date
1. Press the Enter button, the highlighting will move to the row of
numbers.
2. Enter the date in Months, Days, Years. The day of the week is
calculated automatically. Rotate the Jog to change the values
and the Shuttle to navigate.
Date Setup
MM DD YY Day
01 25 60 MON
[CANCEL]
[OK]
3. Press the Enter button to confirm the selection and exit the edit mode.
4. To save the changes and exit the menu: Rotate the Jog to select [OK], then press the Enter
button.
5. To exit the menu without making changes: Rotate the Jog to select [CANCEL], then press the
Enter button.
q
Main Menu → Time/Date → Set Master / Slave
If several multiplexers are installed and connected via RS485 network,
one of the multiplexers may be set as the master clock. This unit will
control the date and time (including daylight savings time) for all of the
other units.
Master/Slave Select
Master Clock
NO
Select One unit from the RS485 network as the master clock by selecting
YES in this menu. All other units must be set as NO (Default).
0150-0193F
33
Kalatel DVMRe Triplex
q
Main Menu → Time/Date → Set Region
Use this menu to set the region for the Auto Daylight Savings Time
feature. Choices are:
Regional Settings
•
OFF: Clock will not be changed automatically, but can still
be adjusted by one hour using the daylight saving macros.
Daylight Saving :
USA
Time Zone
GMT+00:00
•
USA: DST starts at 02:00 on the first Sunday in April.
DST ends at 02:00 on the last Sunday in October.
Includes: United States (except Hawaii, American Samoa,
Guam, Puerto Rico, Virgin Islands, parts of Indiana and
Arizona) and Canada (except Saskatchewan).
SUN,
:
7 APR 2002 02:00 (+1)
SUN, 27 OCT 2002 02:00 (-1)
[CANCEL]
[OK]
•
EUR: DST starts at 01:00 GMT on the last Sunday in
March. DST ends at 01:00 GMT on the last Sunday in
October. Includes: European Union Countries.
•
AUS: DST starts at 02:00 on the last Sunday in October. DST ends at 03:00 on the last Sunday
in March. Includes: South Australia, Victoria, ACT, NSW. Excludes: Tasmania.
The Time Zone must be set correctly to ensure that the DST adjustments are made at the right time. It is
also required for accurate email time stamping.
NOTE
q
The clock will only be automatically adjusted once on a given time and date. If you manually
set the clock back before the last DST change, the time will not get automatically adjusted
again for that same time change.
Main Menu → Time/Date → Network Time Setup
Use this menu to enable/disable and specify how often time synchronization should occur between the
Triplex and the Network Server. The Region /Time Zone must be setup prior to enabling the option.
Update Interval, Select from: Enable, Disable, Once per Day, Twice per Day, and Once per Hour
NTP Primary Server: Enter IP Address of Primary Server.
NTP Backup Server: Enter IP Address of Backup Server.
1. To save changes and exit the menu: Select [OK], then press the Enter button.
2. To exit the menu without making changes: Press the Menu button, or select [CANCEL], and then
press the Enter button.
Network Time Protocol Setup
Update Interval
: DISABLE
NTP Primary Server
:
3. 37.
8. 26
NTP Backup Server
:
0.
0.
[CANCEL]
0.
0
[OK]
Last Update: Never Since Power-up
Warning: Region/Time Zone must be set correctly!
0150-0193F
34
Kalatel DVMRe Triplex
3.9 Sequencing
Use this menu to specify:
•
The multiscreen dwell time.
•
The full screen dwell time.
Multiscreen Dwell
Fullscreen Dwell
The dwell time is the amount of time each camera is displayed on-screen (while sequencing) before
advancing to the next camera.
q
Main Menu → Sequencing → Multiscreen Dwell
Rotate the Jog to change the desired dwell time (from 1 to 30 seconds).
The default is 3 seconds.
q
Multiscreen Dwell
1. Press the Enter button to confirm the selection and exit the menu.
(Time in Seconds)
2. Press the Menu button to exit the menu without making changes.
03
Main Menu → Sequencing → Fullscreen Dwell
Rotate the Jog to change the desired dwell time (from 1 to 30 seconds).
The default is 3 seconds.
Fullscreen Dwell
(Time in Seconds)
1. Press the Enter button to confirm the selection and exit the menu.
03
2. Press the Menu button to exit the menu without making changes.
3.10 Record
Use this menu to:
•
Specify the record quality: High, Medium, or Standard.
•
Specify if a camera is to be used for event recording,
time-lapse recording, or both.
Record Timer
Record Quality
Event Settings
•
Specify the time-lapse record rate per camera.
Timelapse Record Rate
•
Specify the event record rate per camera.
Event Record Rate
•
Specify the activity record rate per camera.
•
Specify the alarm record rate.
•
Set the Record Lock feature.
•
Perform disk maintenance by Deleting, Un-deleting, or
Destroying previously recorded video.
•
Specify how the unit will handle data overwrite issues
once the hard disk becomes full.
Activity Record Rate
Alarm Record Rate
Record Mode
Disk Maintenance
Record Lock
Auto Delete Mode
0150-0193F
35
Kalatel DVMRe Triplex
q Main Menu → Record → Record Timer
Use this menu to setup Preset Record Timer Events.
Day
Start
Stop
Macro
ON/OFF
1. Rotate the Shuttle to select a timed event from the list.
7
22:59
01:59
NONE
ON
2. Press the ENTER button to enter the Edit mode.
MON-FRI
05:56
04:06
10
ON
3. Rotate the Shuttle to navigate to the desired field.
--
--:--
--:--
--
--
4. Rotate the Jog to change the values of the selected field.
[OK]
5. Press the Enter button to exit the Edit mode.
6. Rotate the Jog to highlight the [OK] field and press the
ENTER button to save the changes.
q
Hit ‘ENTER’ to toggle EDIT Mode
Main Menu → Record → Record Quality
Use this menu to specify the record quality for each camera.
Decreasing the record quality decreases the amount of disk space
required to store the images, due to a higher compression
scheme.
Record Quality
Camera 01: High
Camera 02: High
Camera 03: High
Record Quality
Picture Quality
Disk Space Needed
High
Excellent
Most
:
Medium
Good
Medium
:
Standard
Fair
Least
Camera 04: High
Camera 16: High
[CANCEL]
3. Rotate the Jog to navigate, and the Shuttle to change the
values.
[OK]
4. To save changes and exit the menu: Select [OK], then press
the Enter button.
5. Exit the menu without making changes: Press the Menu button, or select [CANCEL], and then
press the Enter button.
q
Main Menu → Record → Event Settings
Use this menu to specify how each camera will record during normal
and event conditions.
TL: Records at the Time-lapse Record Rate under normal conditions.
Does not change record rate during an event.
Event: Records during events at the Event Record Rate. Camera
does not record under normal conditions.
Event + TL: Records at the Time-lapse Record Rate under normal
conditions. Records at the Event Record Rate during events.
0150-0193F
36
Event Camera Settings
Camera
: 01
Type
: Event + TL
Pre Event Duration
: 00
Post Event Duration
: 000
Event Associated Cameras: -- -- -[CANCEL]
[OK]
Kalatel DVMRe Triplex
NOTE
About Events: An Event is an action that the unit acknowledges by recording at the
Event Record Rate, yet it is not cause for an Alarm. Events may be created two ways,
via RS232 text insertion and Activity detection.
Example of an Event: A camera is pointed at the front door inside the lobby during
business hours. With the Event Camera Settings Type set to Event, the unit does not
record while the doorway is empty. When activity motion detection senses that
someone is entering or leaving the doorway, the unit begins recording at the Event
Record Rate and stops recording when the motion ceases.
RS232 Event: See section 9 for information about generating an Event via RS232, and
optionally inserting ASCII text to mark the Event.
Activity Detection Event: See Setup Parameters in section 3.13 for detailed
information about configuring activity detection as an event in the menu system.
Pre Event Duration: The unit will record up to 5 seconds of data ahead of the event trigger, at the
Event Record Rate. Select from 0 to 5 seconds.
Post Event Duration: The unit will record up to 250 seconds after the completion of the Event, at the
Event Record Rate. Select from 0 to 250 seconds.
Event Associated Cameras: Enter up to three camera numbers to be associated with this event.
q
Main Menu → Record → Timelapse Record Rate
The unit records at the Timelapse Record Rate under normal conditions, when there are no alarms,
events, or activity present. Record rates are measured in both Pictures Per Second (pps) and Seconds
Per Picture (spp).
The maximum record rate per camera is inversely proportional to the number of cameras connected to
the unit. The fewer cameras connected, the higher the maximum record rate for each camera, and vice
versa. The maximum record rate for multiple cameras is 48pps (NTSC)(40pps PAL). The maximum
record rate for a single camera is 30pps (NTSC)(25pps PAL).
The bottom right corner of the menu contains a record duration calculator. The top line indicates the
estimated recording time for the unit in Time-lapse record mode only. The bottom line indicates the
estimated recording time, taking into consideration the amount of time the unit will spend in Activity,
Event, and/or Alarm record mode.
Timelapse Record Rate
Camera
1 : 0.40 pps 2.5 spp
Camera
2 : 0.29 pps 3.5 spp
Camera
3 : 0.34 pps 2.9 spp
Camera
4 : 0.57 pps 1.8 spp
:
:
:
Camera 15 : 0.40 pps 2.5 spp
Camera 16 : 0.40 pps 2.5 spp
8 days 5 h (TL)
[CANCEL]
[OK]
8 days 5 h (Total)
1. Rotate the Jog to navigate, and the Shuttle to change the values.
0150-0193F
37
Kalatel DVMRe Triplex
2. To save changes and exit the menu: Select [OK], and then press the Enter button.
3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then
press the Enter button.
q
Main Menu → Record → Event Record Rate
The unit will record at the Event Record Rate when an Event is activated. Events can be activated by
RS232 event generation or activity detection. See Event Settings on page 35.
Record rates are measured in both Pictures Per Second (pps) and Seconds Per Picture (spp).
The maximum record rate per camera is inversely proportional to the number of cameras connected to
the unit. The fewer cameras connected, the higher the maximum record rate for each camera, and vice
versa. The maximum record rate for multiple cameras is 48pps (NTSC)(40pps PAL). The maximum
record rate for a single camera is 30pps (NTSC)(25pps PAL).
The bottom right corner of the menu contains a record duration calculator. The top line indicates the
estimated recording time of the cameras in Event record mode only. The bottom line indicates the
estimated recording time, taking into consideration the amount of time the unit will spend in Time-lapse,
Activity, Event, and/or Alarm record mode.
Event Record Rate
Camera
1 : 0.40 pps 2.5 spp
Camera
2 : 0.29 pps 3.5 spp
Camera
3 : 0.34 pps 2.9 spp
Camera
4 : 0.57 pps 1.8 spp
% Time: 4%
:
:
Estimate of the % of time each
camera will typically spend in
Event mode. For example if you
expect to have about 20 total
events each day, each lasting 3
minutes on average, then the %
of the time will be 4%.
(1 hour/24 hours)
:
Camera 15 : 0.40 pps 2.5 spp
Camera 16 : 0.40 pps 2.5 spp
125 days 8 h (EVENT)
[CANCEL]
[OK]
10 days 7 h (Total)
1. Rotate the Jog to navigate, and the Shuttle to change the values.
2. To save changes and exit the menu: Select [OK], and then press the Enter button.
3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then
press the Enter button.
q
Main Menu → Record → Activity Record Rate
The unit will record at the Activity Record Rate when the camera is in normal Timelapse Record Mode
and activity is detected in the camera scene. Activity should not be linked to Event, in which case the
Event Record Rate will be used.
Record rates are measured in both Pictures Per Second (pps) and Seconds Per Picture (spp).
0150-0193F
38
Kalatel DVMRe Triplex
The maximum record rate per camera is inversely proportional to the number of cameras connected to
the unit. The fewer cameras connected, the higher the maximum record rate for each camera, and vice
versa. The maximum record rate for multiple cameras is 48pps (NTSC)(40pps PAL). The maximum
record rate for a single camera is 30pps (NTSC)(25pps PAL).
The bottom right corner of the menu contains a record duration calculator. The top line indicates the
estimated recording time of the cameras in Activity record mode only. The bottom line indicates the
estimated recording time, taking into consideration the amount of time the unit will spend in Time-lapse,
Activity, Event, and/or Alarm record mode.
Activity Record Rate
Camera
1 : 0.40 pps 2.5 spp
Camera
2 : 0.29 pps 3.5 spp
Camera
3 : 0.34 pps 2.9 spp
Camera
4 : 0.57 pps 1.8 spp
% Time: 4%
:
Estimate of the % of time each
camera will typically spend in
periods of activity. For example
if you expect to have about 20
total periods of activity each day,
each lasting 3 minutes on average,
then the % of the time will be 4%.
(1 hour/24 hours)
:
:
Camera 15 : 0.40 pps 2.5 spp
Camera 16 : 0.40 pps 2.5 spp
68 days 11 h (ACTIVITY)
[CANCEL]
[OK]
9 days 16 h (Total)
1. Rotate the Jog to navigate, and the Shuttle to change the values.
2. To save changes and exit the menu: Select [OK], and then press the Enter button.
3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then
press the Enter button.
q
Main Menu → Record → Alarm Record Rate
During an alarm, the unit records at the alarm record rate. The bottom of the menu contains a record
duration calculator. The top line indicates the estimated recording time of the cameras in Alarm record
mode only. The bottom line indicates the estimated recording time, taking into consideration the amount
of time the unit will spend in Time-lapse, Activity, Event, and/or Alarm record mode.
The configuration of the Alarm Record Rate is closely associated with the Alarm Record Mode. For
detailed information about configuring the Alarm Record Mode, see Alarm Record mode in section 3.11.
0150-0193F
39
Kalatel DVMRe Triplex
Global Alarm Record Rate
% Time:
60 pps
1%
40 days 20 h (Alarm)
15 days 11 h (Total)
[CANCEL]
[OK]
Estimate of the % of time the
unit will typically spend in
alarm mode. For example
if you expect to have about 5
total periods of alarms each day,
each lasting 3 minutes on average,
then the % of the time will be 1%.
(15 min/24 hours)
Record
Duration
Calculator
1. Rotate the Jog to navigate, and the Shuttle to change the values.
2. To save changes and exit the menu: Select [OK], and then press the Enter button.
3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then
press the Enter button.
q
Main Menu → Record → Record Mode
No overwrite
Use this menu to specify how the unit will handle data overwrite
issues once the hard disk becomes full.
Write once
Continuous
No Overwrite:
•
•
•
Recording starts at the end of the last recording.
Recording stops when disk becomes full.
When the hard disk becomes full, the unit displays an on-screen message indicating that the
device is full and that the archive device has stopped recording. The user must acknowledge the
message by pressing the Enter button.
Write Once:
•
•
•
Recording starts at the end of the last recording.
Recording stops when disk becomes full.
The user is prompted to authorize overwriting old data.
Continuous:
q
•
Recording starts at the end of the last recording.
•
•
Unit overwrites all previously recorded data, overwriting the oldest data first.
The unit does not stop recording when disk becomes full.
Main Menu → Record → Disk Maintenance
Use the Jog to select from the following options, then press the
Enter button to begin.
Delete
Delete: Delete all data from the hard disk (with the possibility of restoring it).
UnDelete
Undelete: Restore data that has been deleted, but not yet overwritten.
Destroy
Destroy: Erase all data from the hard disk permanently, without the possibility
of restoring it. Selecting this option brings up a confirmation dialog box.
0150-0193F
40
Kalatel DVMRe Triplex
q
Main Menu → Record → Record Lock
Use this menu to set the Record Lock feature. This feature disables the front panel
record button. Setting Record Lock to ON will start the unit recording if it is not currently
in the Record mode.
q
OFF
ON
Main Menu → Record → Auto Delete Mode
The ADM feature prevents the unit from displaying or archiving any search results that are more than
thirty days old. This feature may be required by law in some jurisdictions. Choose from 7 to 99 days or
Off. The default setting is Off.
ADM Setting
Message
ADM will change. Are you sure?
99
Days
Yes
3.11 Alarms
Use this menu to configure the alarm handling features of the unit.
Input Configuration
Alarm Latch
Alarm Action
Alarm Record Mode
Caution! The DVMRe Triplex’s primary function is to furnish
video multiplexing and recording with a multiscreen display.
Although the unit has alarm handling and motion detection
functions, these are considered secondary features. This unit
should not be the only alarm device on site.
Enable / Disable
Alarm History
Link to a Macro
Fullscreen Alarm
Relay Configuration
Buzzer Setup
Videoloss Action
Pre Alarm Duration
Notification
Archive Alarms
q
Main Menu → Alarms → Input Configuration
Configure the alarm inputs as either Normally Open or Normally Closed.
Configure inputs as follows.
Normally Open Zero Potential Relay Contact: Configure in menu as
Normally Open.
Normally Closed Zero Potential Relay Contact: Configure in menu
as Normally Closed
TTL Active High: Configure in menu as Normally Closed.
TTL Active Low: Configure in menu as Normally Open.
Open Collector Active On: Configure in menu as Normally Open.
Open Collector Active Off: Configure in menu as Normally Closed.
0150-0193F
41
Kalatel DVMRe Triplex
q
Main Menu → Alarms → Alarm Latch
This feature determines how the unit latches alarm conditions.
Latched
Select from the following options:
Transparent
Latched: The alarm is activated until it is silenced and acknowledged
by the user.
Timed Out
Transparent: The alarm is active only while receiving alarm input.
The alarm condition is canceled when the alarm input ceases.
Timed Out: The alarm condition is latched for the amount of time selected in this menu, then it is
automatically silenced and acknowledged. If the alarm input exceeds the duration specified in this
menu, the unit silences and acknowledges the alarm when the alarm input ceases. Select the timeout
duration, the range is from 1 to 250 seconds.
Transparent alarms cannot be silenced and acknowledged. If transparent mode is preferred, but the
ability to silence and acknowledge alarms is desired, select Timed Out and set the Alarm Timeout to
two seconds.
q
Main Menu → Alarms → Alarm Action
This menu is not available on 4-channel units. Only the full
screen alarm display is available on the 4-channel unit.
Therefore, a 4 channel unit will always be limited to the default
values in this menu, i.e. no presets linked to alarms and alarm
relay is always Relay 1.
Input: Select the input you wish to configure.
Freeze: Selecting Yes will freeze the alarm camera display
(quadrant 1) at the time the alarm is activated.
Cameras: This setting determines the four cameras displayed
on-screen when an alarm is received. The camera group contains
the camera in alarm and three associated cameras.
Alarm Action Setup
Input
: 01
Freeze
: Yes
Cameras
: 01 16 02 03
Presets
: 01 -- 09 --
Relay
: 1
Intrusion AND/OR: OR
[CANCEL]
[OK]
Default Settings: The first camera in the list is the camera in alarm.
The second camera in the list is the camera that precedes the alarm camera numerically. The third
and fourth cameras in the list are the two cameras following the alarm camera numerically.
Preset: Use this feature to send a camera to a preset when an alarm is activated. The preset number
corresponds directly with the camera number located directly above it in this menu. Select from 1
through 16. If this field is left blank, the camera will not respond. In the example above, Camera 1 will
go to Preset 1, while Camera 2 will go to Preset 9.
Relay: Configure which relay will be triggered when an alarm is activated per camera. Select from:
•
1
•
1+2
•
2
•
None
Intrusion AND/OR: Use this feature to activate alarms by hardwired alarm inputs AND/OR Intrusion
detection. Select from AND or OR. Motion Detection must be set to Intrusion and linked to the Alarm
number.
Rotate the Jog to navigate and the Shuttle to change the values.
0150-0193F
42
Kalatel DVMRe Triplex
q
Main Menu → Alarms → Alarm Record Mode
Use this menu to determine how the unit will record cameras in alarm.
No Change: Unit changes to the Alarm Record Rate, but it does not
give priority to the camera in alarm.
Alarm Record Mode
Select Mode
Interleaved
Exclusive: The unit records only the camera (or cameras) in alarm.
Interleaved: Alarmed cameras are recorded at a higher rate than
non-alarm cameras. The unit accomplishes this by interleaving images
of alarmed cameras between images from non-alarmed cameras in the record list. Interleaved is the
recommended mode of operation.
Example of Record Lists:
q
No Change record list for 8 cameras, Camera-4 in alarm.
1234567812345678
Exclusive record list for 8 cameras, Camera-4 in alarm.
4444444444444444
Interleaved record list for 8 cameras, Camera-4 in alarm.
1424345464748414
Main Menu → Alarms → Enable / Disable
Individual Enable
Use this menu to Enable or Disable the alarm inputs.
Enable All
Select from the following:
Disable All
•
Individual Enable: Allow the user to access the Alarm
Enable submenu, and enable or disable alarm inputs on
a per camera basis.
•
Enable All
•
Disable All
Rotate the Jog to navigate, and the Shuttle to change
the values.
Save changes and exit the menu: Select [OK], then press the
Enter button.
Exit the menu without making changes: Press the Menu
button, or select [CANCEL], then press the Enter button.
q
Main Menu → Alarms → Alarm History
Alarm History Box
Use this window to view a list of the 100 most recent alarms.
Alarms are displayed 10 at a time. Rotate the Jog to scroll
through the alarms.
001- 02/04 18:40:32 16
Information displayed in this window is:
003- 02/28 10:10:20 08
•
The alarms number in the list.
•
The date of the alarm (month and day).
•
The time of the alarm (hours, minutes, and seconds).
002- 02/15 12:00:10 11
:
:
010- 03/15 05:12:16 04
[OK]
The number of the camera input in alarm.
0150-0193F
43
Kalatel DVMRe Triplex
q
Main Menu → Alarms → Link To A Macro
Use this menu to link an alarm input to a macro. If a link is created,
a macro will run each time that alarm is activated.
Alarm: Select the alarm input you would like to link.
Macro: Select the macro number you wish to link to. Leave this
setting blank if you do not wish to link to a macro.
Rotate the Jog to navigate, and the Shuttle to change
the values.
Save changes and exit the menu: Select [OK], then press the
Enter button.
Exit the menu without making changes: Press the Menu
button, or select [CANCEL], then press the Enter button.
q
Main Menu → Alarms → Fullscreen Alarm
Selecting Yes from this menu will cause the unit to always display
the alarm camera fullscreen.
Selecting No from this menu will cause the unit to display the 4-way
display configured in the Main Menu → Alarms → Alarm Action
Setup menu.
Fullscreen Alarm
Fullscreen
NO
This menu selection is not available on 4-channel DVMRe Triplex units, since Fullscreen Alarm Mode is
the only alarm mode available.
q
Main Menu → Alarms → Relay Configuration
Relay Configuration
Use this menu to configure each relay output as either:
•
Normally Open
•
Normally Closed
q
Relay 01: N/OPEN
Relay 02: N/CLOSED
[CANCEL]
[OK]
Main Menu → Alarms → Buzzer Setup
Use this menu to configure the internal buzzer.
Global Buzzer: The Global Buzzer setting acts as a master On/Off
switch. Setting the Global Buzzer to OFF deactivates all buzzer
activity.
Buzzer Setup
Global Buzzer
: ON
Live Alarm Buzzer: ON
Live Alarm Buzzer: Activates while receiving alarm input.
Videoloss Buzzer : ON
Videoloss Buzzer: Activates when video loss is detected.
Playback Buzzer
Disabling the Videoloss buzzer disables all videoloss buzzer activity.
Videoloss buzzers may be disabled on a per camera basis in the
Alarms → Videoloss Action menu.
[CANCEL]
: ON
[OK]
Playback Buzzer: Activates during playback of recorded alarms.
0150-0193F
44
Kalatel DVMRe Triplex
q
Main Menu → Alarms → Videoloss Action
Use this menu to configure how the unit responds to videoloss.
Videoloss Action
Camera: Select the camera you wish to configure.
Relay 1: If enabled, the unit will activate Relay 1 when videoloss
is detected.
Camera : 01
Relay 1: Disable
Relay 2: Enable
Relay 2: If enabled, the unit will activate Relay 2 when videoloss is
detected.
Buzzer: Use this setting to disable the videoloss buzzer activation
on a per camera basis. To disable videoloss buzzer activation on
all cameras go to the Main Menu → Alarms → Buzzer Setup menu,
described in the previous section.
q
Main Menu → Alarms → Pre Alarm Duration
During recording, the unit stores up to 5 seconds of recorded
information in a buffer. This data can be automatically retrieved when
an alarm is activated. Select the amount of time just previous to the
activation of an alarm you wish to retrieve.
q
Buzzer : Enable
[CANCEL]
[OK]
Pre Alarm Duration
(Time in Seconds)
05
Main Menu → Alarms → Notification
Use this menu to select:
Email
•
Email Alarm Notification.
•
TCP/IP Notification.
TCP/IP
Email Notification Setup
This screen allows the user to setup the types of events to be notified of, and the email addresses (up
to two) to be notified. Follow the context sensitive on-screen instructions to setup the individual fields.
Also, please note that the Region/Time Zone setting must be set correctly for Email notification to time
stamp messages accurately.
0150-0193F
45
Kalatel DVMRe Triplex
Email Notification Setup
One or more of these
fields must be set to
ENABLE to receive an
email notification of
the selected event.
Notify Vidloss:
ENABLE
Notify Alarm:
DISABLE
Notify Record:
DISABLE
Notify Archive:
DISABLE
Notify Menu Access: DISABLE
Obtain the parameters
for these two fields from
your IT Department.
Notify Power Up:
DISABLE
Notify Connection:
DISABLE
Email User 1:
john.doe
Email Domain 1:
somecompany.com
Email User 2:
jane.doe
Email Domain 2:
somecompany.com
SMTP Server:
0.
SMTP Port:
25
0.
0.
[CANCEL]
0
[OK]
Format of email address: user@domain
Warning: Region/Time Zone must be set correctly!
Email Address Format
The format of the email addresses should be entered as follows. If the email address to be notified is
john.doe@somecompany.com, then john.doe should be entered in one of the Email User fields and
somecompany.com should be entered in the subsequent Email Domain field.
TCP/IP Notification Setup
This screen allows the user to setup the types of events to be notified of, and the IP addresses (up to
two) of the PC(s) where the WaveReader software resides.
WaveReader must be running on the receiving PC(s) and Alarm Monitoring must be setup. See Alarm
Monitoring in the WaveReader Manual for details.
0150-0193F
46
Kalatel DVMRe Triplex
TCP/IP Notification Setup
One or more of these
fields must be set to
ENABLE to receive an
email notification of
the selected event.
The IP Addresses
of the PC on which
the WaveReader
Software resides
Notify Vidloss:
DISABLE
Notify Alarm:
DISABLE
Notify Record:
DISABLE
Notify Archive:
DISABLE
Notify Menu Access:
DISABLE
Notify Power Up:
DISABLE
Notify Connection:
DISABLE
Primary Host:
0.
0.
0.
0
Backup Host:
0.
0.
0.
0
Port:
1027
Notification Interval (minutes): Immediate
[CANCEL]
[OK]
The Notification Interval can be set from 1 minute to 60 minutes, or immediately upon the event.
q
Main Menu → Alarms → Archive Alarms
Selecting Enable from this menu will cause the unit to activate
Relay 2 if a malfunction occurs while archiving.
Archive Alarm
Relay 2
ENABLE
3.12 Macro
A macro is a recorded sequence of keystrokes. The number of macros depends on the number of
camera inputs (4, 10 or 16). Each macro can have up to 32 keystrokes.
Use this menu to:
•
•
•
q
Macro Record
Enter Macro Record mode.
Program a scheduled start time for a macro.
Edit the RS232 command string for each submacro.
Timed Macro Start
Edit Submacro
Main Menu → Macro → Macro Record
Note: Do not attempt macro programming while the front panel is locked.
Macro Record
To begin recording a macro:
Select Macro
1. Select the macro number you wish to record, then press the
Enter button. The unit will automatically exit the menu
system and go to a starting point. Macro Record mode
is indicated as F and the Macro Number on-screen.
01
2. From this point, begin recording the desired keystroke sequence. Record up to 32 keystrokes. If
32 keystrokes are exceeded, the unit will end the macro recording automatically.
3. When finished programming, press the Function button then the Enter button to end the macro
recording. A form is provided in section 10 to keep track of recorded macro functions.
0150-0193F
47
Kalatel DVMRe Triplex
NOTE
Keystroke count while in the menu system: While recording a macro, entering the
menu system, changing multiple menu items, and exiting the menu system are only
counted as one keystroke. Using the Jog to navigate the menu system does not count
as keystrokes. Once the menu system has been exited, re-entering the menu system
will count as a second keystroke.
Not all menu items can be programmed using macros. For a complete list of macro
programmable menu items, see the table below.
During macro recording, the following button combinations perform special functions.
Button Sequence
Resulting Action
Function then 1.
Activate Relay 1 output.
Function then 2.
Reset Relay 1 output.
Function then 3.
Pause macro for 1 second.
Function then 4.
Pause macro for 5 seconds.
Function then 5.
Activate Relay 2 output.
Function then 6.
Reset Relay 2 output.
Function, Function, then
Submacro number.
Program a specific submacro to activate when the macro is run.
Function then Enter.
End macro recording
Macro Excluded Features
The following core features or settings cannot be programmed by Macro.
•
•
•
•
•
•
•
q
Disk Maintenance.
Erase Archive Medium.
POTS Setting.
Ethernet Setting.
RS485 Network Address.
Front Panel Lock/Unlock.
Record Timer.
Main Menu → Macro → Timed Macro Start
Use this menu to program scheduled start times for macros. Up
to 20-scheduled start times can be programmed in this menu.
Timed Macro Setup
Event: Select the scheduled start event you wish to edit.
Event : 01
Day: Select the start day (Monday – Sunday) of the macro.
Select ** (double asterisks) to run the macro every day.
Select None to cancel the scheduled start time.
Day
: Monday
Time
: 00:00
Time: Select the start time for the macro.
Macro : 01
[CANCEL]
[OK]
Macro: Select the desired macro number.
A form is provided in section 10 to keep track of scheduled macros.
0150-0193F
48
Kalatel DVMRe Triplex
q
Main Menu → Macro → Edit Submacro
A submacro is an RS232 command string that is used to control a peripheral device. Submacros are
activated during macros. See the table above for information about programming a macro to activate
a submacro.
Select the submacro you wish to edit from the menu system. This menu will appear.
Edit Submacro 01
080 066 066 010 --- --- --- --- --- --[P] [B] [B] [0]
[CANCEL]
[OK]
ENTER key starts Submacro edit
Use this menu to create the RS232 command string. Press the Enter button to Enter and Exit the
submacro edit mode. Rotate the Jog/Shuttle to navigate among the fields and change the values.
Each byte value can be set from 0 to 255.
Running A Macro
A macro is a recorded sequence of up to 32 keystrokes. To activate a
macro, press the Function button followed by the Number button of the
desired macro. While running, the macro is indicated on-screen as the letter
F and the macro number.
The user can cancel the macro at any time by pressing the Function button.
{F}
1
Function and
Number Buttons
Daylight Savings Time (Alternate Method)
To adjust the time one hour for daylight savings time, press the Function
button, then the Sequence button. If this function is activated during April,
one hour is added to the time. If this function is activated in October, one
hour is subtracted from the time. This function will only operate once per
time period.
{F}
Function and
Sequence Buttons
3.13 Motion Detection
Use this menu to:
•
•
Enable motion detection on a per camera basis.
Activate individual zones in a scene to respond to motion
detection.
•
•
Activate the on-screen motion detection indicator.
Set motion detection as Activity detection or Intrusion Detection.
•
Configure the motion detection parameters on a per camera basis.
0150-0193F
49
Enable/Disable Detection
Setup Parameters
Setup Active Zones
Indicate Detection
Kalatel DVMRe Triplex
q
Main Menu → Motion Detection → Enable/Disable Detection
Selecting Enable All or Disable All from this menu will activate or deactivate
motion detection on all cameras.
Selecting Individual Enable from this menu will bring up the following menu.
Individual Enable
Enable All
Disable All
Individual Enable Menu
Use this menu to enable or disable motion detection on a per
camera basis. Rotate the Jog to navigate, and the Shuttle
to change the values.
Detection Enable
Camera 01: Enable
Camera 02: Disable
Camera 03: Enable
:
:
Camera 16: Enable
[CANCEL]
q
[OK]
Main Menu → Motion Detection → Setup Parameters
Use this menu to select the Camera, Motion Detection Type, and Sensitivity of the Motion Detection
you wish to configure.
Motion Detection Parameters Setup
Camera
01
Motion Detection Type
ACTIVITY
Sensitivity
06
Relay Output
2
Link to Event
---
Rejection
LOW
Target Size
01
Link to Alarm
NONE
[CANCEL]
[OK]
Navigate in this menu using the Jog to select the field and the Shuttle to change the parameters.
Activity Vs. Intrusion
Activity Detection is a simple type of motion detection having only a sensitivity setting and a relay
output. Intrusion Detection is a more sophisticated type of motion detection, with additional features
such as false alarm rejection levels, minimum target size, and an alarm output.
Activity Detection Setup
If Activity is selected in Motion Detection Type field, the following parameters are enabled:
0150-0193F
50
Kalatel DVMRe Triplex
Relay Output: The unit may be configured to activate a relay output when motion detection is
present. Select either 1, 2, 1+2 (both relays), or None.
Link to Event: Selecting Yes in this menu will activate the event record speed when activity detection
is present.
Intrusion Detection Setup
If Intrusion is selected in Motion Detection Type field, the following parameters are enabled:
Sensitivity: Rotate the Shuttle to change the motion detection sensitivity, 10 being the most
sensitive.
Rejection: Configure the unit’s false alarm rejection feature by selecting Low, Medium, or High.
These settings are based on the number of simultaneously triggered zones and the persistence of
motion in a scene. The Low setting is the most sensitive to motion. The Medium setting will filter out
most false alarm situations due to sudden luminance changes over the whole scene (clouds passing
over). The High setting will filter out sudden luminance changes as well as spurious motion events
that do not persist for a number of frames (a bird flying past the lens).
Target Size: This setting is the minimum number of zones (from the 16 x 16 grid) that must be
activated simultaneously before it is considered to be valid motion.
Link To Alarm: Select the alarm number that you wish to activate when motion detection is activated.
q
Main Menu → Motion Detection → Setup Active Zones
Use this menu to setup the Active Zones for motion detection. The screen shown below will overlay the
current video image allowing for precise activity zone setup. The disabled zones will be tinted. The
enabled zones will be clear.
Activity Grid Setup Screen
5
0150-0193F
51
Kalatel DVMRe Triplex
Pressing the Function button will bring up the Help screen shown on the next page. This screen will
overlay the current video image.
{F}
Function
Button
‘MENU’ : Exit Activity Setup
‘ENTER’: Save and Exit Activity Setup
‘PAUSE’: Toggle between Enable and Neutral
‘STOP’ : Toggle between Disable and Neutral
‘ZOOM’ : Disable/Enable all zones
‘PLAY FORWARD’: Increase the Sensitivity level
“PLAY REVERSE’: Decrease the Sensitivity level
Sensitivity Scope
Use the sensitivity scope to adjust the motion detection sensitivity for the scene. The
sensitivity scope is the bar located near the left-hand corner of the screen.
The black bar raises and lowers to indicate the degree of motion detected. When the
black bar reaches the red bar, a motion detection alarm is activated.
Adjusting Motion Detection Sensitivity: Raise and lower the red bar to change the
motion detection sensitivity. Use the Play Forward button to increase the sensitivity level
and the Play Reverse button to decrease the sensitivity level. The sensitivity level is also
displayed as a numeric value.
Play Reverse to decrease the Sensitivity
Play Forward to increase the Sensitivity
q
Main Menu → Motion Detection → Indicate Detection
Motion Detection may be indicated on-screen by displaying the letter M.
Use this menu to turn this feature On or Off.
Indicate Detection
Detection
ON
3.14 Camera Setup
Use this menu to:
q
•
Edit the title for each camera.
Camera Titles
•
•
Adjust the Automatic Gain Control.
Disable or Enable camera inputs.
Camera AGC
•
Specify cameras as covert (recorded but not displayed).
Covert Camera
•
View the Camera Scope (Histogram)
Camera Scope
Camera Disable
Main Menu → Camera Setup → Camera Titles
Use this menu to:
• Specify if the camera titles will be displayed on the monitors.
Edit the title for each camera.
0150-0193F
52
Titles Display
Edit Titles
Kalatel DVMRe Triplex
Titles Display
Titles Display
Camera titles may be displayed on either monitor. Use this menu
to turn this feature On or Off.
Monitor A: ON
Monitor B: OFF
[CANCEL]
Rotate the Jog buttons to navigate and the Shuttle to change the values.
[OK]
Edit Titles
Rotate the Shuttle to select the camera whose title you wish to configure, and then press the Enter
button. The Camera Title Edit menu will appear.
Camera Title Edit
Camera
1
Title :
Camera 01
[CANCEL]
[OK]
@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^
SEQ key selects character bank
‘1’ key inserts blank character
‘2’ key inserts selected character
Camera Title Edit Menu
1. With the camera title selected, press the Enter button. The menu will enter the Edit mode and the
character bank will appear in the center of the menu.
2. Press the Sequence button to select the desired character set.
3. Rotate the Shuttle to navigate the cursor in the camera title.
4. Rotate the Jog to navigate the cursor in the character bank.
5. Press the Number 1 button to insert a blank character or press the Number 2 button to insert the
selected character.
6. When finished editing the title, press the Enter button to exit the edit mode.
7. Save changes and exit the menu: Select [OK], then press the Enter button.
8. Exit the menu without making changes: Press the Menu button, or select [CANCEL], then press
the Enter button.
q
Main Menu → Camera Setup → AGC
Use the Automatic Gain Control (AGC) to adjust the video input
signal level for cameras whose level is outside the normal range.
The default gain setting is 100%.
Rotate the Jog to navigate and the Shuttle to change the values.
Save changes and exit the menu: Select [OK], then press the
Enter button.
Exit the menu without making changes: Press the Menu button,
or select [CANCEL], then press the Enter button.
0150-0193F
53
Signal Gain Setup
Camera 01
Signal Gain 100%
[CANCEL]
[OK]
Kalatel DVMRe Triplex
Main Menu → Camera Setup → Camera Disable
Use this menu to:
Individual Disable
•
•
Enable or Disable cameras individually
Configure the unit to disable cameras automatically at power-up
if video loss is detected.
Power Up Disable
•
Automatically disable all inputs detecting videoloss.
Individual Disable
Auto Disable Now
Camera Disable
Use this menu to Disable or Enable each camera input
individually.
Use the Jog to navigate and the Shuttle to change the values.
Save changes and exit the menu: Select [OK], then press
the Enter button.
Exit the menu without making changes: Press the Menu
button, or select [CANCEL], then press the Enter button.
Camera 01: Disable
Camera 02: Enable
Camera 03: Disable
Camera 04: Enable
:
:
Camera 16: Enable
[CANCEL]
[OK]
Power Up Disable
With this feature turned On (Enabled), the unit will automatically detect
which inputs are experiencing videoloss at power-up, and
disable them.
Rotate the Jog to navigate and the Shuttle to change the values.
Power Up Disable
Disable
OFF
Auto Disable Now
This feature detects which inputs have video signals and which are experiencing videoloss. When this
feature is activated, the unit will automatically disable the inputs experiencing videoloss. The DVMRe
Triplex will also re-enable video inputs that were previously disabled if a video input signal is detected.
q
Main Menu → Camera Setup → Covert Camera
This feature removes cameras from all live displays while continuing
to record them, so that the users and the public are unaware that the
camera is being recorded. Covert cameras are viewable during playback.
Select Yes in this menu to configure a camera as covert.
Rotate the Jog to navigate and Shuttle to change the values.
Covert Camera
Camera 01: NO
Camera 02: YES
Camera 03: NO
Camera 04: NO
:
:
Camera 16: NO
[CANCEL]
0150-0193F
54
[OK]
Kalatel DVMRe Triplex
q
Main Menu → Camera Setup → Camera Scope
Use this menu to view a live luminance histogram of the currently displayed camera.
Luminance Histogram
A Luminance Histogram is a graphical representation of how many times each gray-level value occurs in
an image.
Use this feature to analyze and optimize the video input signal.
Luminance Histogram
%L
0
Black
White
Luminance
3.15 Archive Setup
Data recorded by the unit can be archived to an external
archive device.
Use this menu to:
• Select the Port where the archive device will be connected.
• Turn Background Archiving mode Off and On.
• Erase the recorded data on a compatible archive device.
•
q
Port Select
Background Archive
Erase Archive Medium
QuickWave Setup
Enable or Disable QuickWave Setup.
Main Menu → Archive Setup → Port Select
Select the Port or interface to which the archive device will be connected.
Select from the following items.
SCSI: SCSI archive devices.
1394: 1394 Firewire archive devices.
0150-0193F
55
SCSI
1394
Kalatel DVMRe Triplex
q
Main Menu → Archive Setup → Background Archive
Background Archive: Commands the unit to record data to both the
hard disk and the archive device simultaneously.
Select from the following items.
OFF: Turns background archiving Off.
ON: Turns background archiving On.
q
ON
Main Menu → Archive Setup → Erase Archive Medium
Use this feature to erase all of the recorded data on an
archive device.
With Erase Archive Medium highlighted, press the Enter
button. If a compatible archive device is connected, a
confirmation box will appear, otherwise no action will occur.
q
OFF
Main Menu → Archive Setup → QuickWave Setup
This feature provides the option of having the QuickWave software
written to any CDs that are created. This allows the CD to be read
on any PC without installing software. Select ON to enable, OFF to
disable.
Message
Erase all Records. Are you sure?
YES
QuickWave Setup
QuickWave CD Write: ON
[CANCEL]
[OK]
3.16 Audio Setup
Use this menu to enable or disable the audio feature of the Triplex. Select
from:
•
OFF
•
G.711
OFF
G.711
Audio Limitations:
1. To record audio at least one the unit’s video inputs must be set to record video at a rate of 1pps
or faster.
2. If all the cameras are set to EVENT mode and no events are occurring, no audio will be recorded
regardless of the event recording speed.
3.17 Communications
Use this menu to:
•
•
Configure the baud rates and settings for the RS232 ports.
Configure the network address for the RS485 network.
•
Configure the Ethernet address and networks settings.
q
Main Menu → Communications → RS232
Select the Port you wish to configure and press the ENTER button.
0150-0193F
56
RS232
RS485
Ethernet
Port 1
Port 2
Kalatel DVMRe Triplex
Port 1
Use this menu to:
•
•
POTS Setup
Enable/Disable POTS and configure the Modem initialization
string (POTS Setup).
Baud Rate
Adjust the Baud rate.
POTS Setup
The default modem string (shown below) is for use with Hayes Accura 56k, Diamond Supra Express
56k, and 5686 US Robotics modems in their default conditions. Consult with the modem manual
before attempting to make any changes. It is strongly recommended that the modem initialization
string only be modified by a qualified technician.
POTS Setup
POTS : DISABLE
Modem Init String : AT&F1&K3M0E1Q0V1S0=0&R2&C1&D0&H1
[Default Modem String]
[CANCEL]
[OK]
@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^
SEQ key selects character bank
‘1’ key inserts blank character
‘2’ key inserts selected character
1. With the Modem Init String highlighted, press the Enter button to enter the Edit mode. The
character bank will appear in the center of the menu.
2. Press the Sequence button to select the desired character bank.
3. Rotate the Shuttle to navigate the Modem Init String.
4. Rotate the Jog to select a character from the character bank.
5. Use the Number 2 button or rotate the Shuttle to insert the desired character from the character
bank into the Modem Init String and advance to the next character.
6. Use the Number 1 button to insert a blank character.
7. When finished, press the Enter button.
8. To save the changes and reboot, select OK, then press the Enter button. The unit will only reboot
if changes were made to the Modem Init String.
9. To exit the menu without making changes, select Cancel, then press the Enter button. Pressing
the Menu button also exits the menu without making changes.
0150-0193F
57
Kalatel DVMRe Triplex
Baud Rate
Use this menu to configure the baud rate for Port 1. Rotate the
Jog to select a baud rate from the menu.
Save changes and exit the menu: Press the Enter button.
Exit the menu without making changes: Press the Menu button.
Port 2
Use this menu to configure the baud rate for Port 2. Rotate the
Jog to select a baud rate from the menu.
Save changes and exit the menu: Press the Enter button.
Exit the menu without making changes: Press the Menu button.
The RS232 port 2 is used for Event Generation and ASCII Text
Insertion. See Section 7 for the RS232 Protocol required to perform
these functions.
q
Main Menu → Communications → RS485
1200
2400
4800
9600
19200
38400
57600
Baud
Baud
Baud
Baud
Baud
Baud
Baud
1200
2400
4800
9600
19200
38400
57600
Baud
Baud
Baud
Baud
Baud
Baud
Baud
Network Address
Connect several units to a single keyboard, or vice-versa. Up to
32 units (any combination of multiplexers and keyboards) can be
networked together. Use this menu to specify the units unique network address.
01
Save changes and exit the menu: Press the Enter button.
Exit the menu without making changes: Press the Menu button.
q
Main Menu → Communications → Ethernet Settings
An ethernet connection can be used to connect to the unit from a
PC for the viewing of live or recorded images. Use this menu to
configure the Ethernet communications settings. Select from the
following:
Ethernet: Select Enable or Disable.
Hostname: Not selectable. Pulled from the systems serial number.
DHCP: Select Enable or Disable. Enables dynamic IP addressing.
When DHCP is enabled, the IP address, Subnet Mask, Gateway,
and Server fields are dynamically addressed.
Name Service: Select from Disable or WINS. Enabling WINS
registers the hostname and IP address within the current Network.
This ensures that you can connect to the Triplex by hostname
within the network.
IP Address / Subnet Mask / Gateway: Consult with a qualified
Network Administrator or an MIS professional to configure these
settings if DHCP is not enabled.
Ethernet Settings
Ethernet
: Enable
Hostname
: D406T2250419
DHCP
: Disable
Name Service
: Disable
IP Address
:
Subnet Mask
: 255.255.254.
0
Gateway
:
3. 18.172.
1
Primary Name Server
:
3. 18.173. 12
Backup Name Server
:
3. 18.173. 13
Print Server
:
3. 18.173. 11
TCP MTU Size
3. 18.173. 60
: Standard
[CANCEL]
[OK]
Primary Name Server / Backup Name Server: The IP addresses of the Primary and Backup Name
Servers. Not required if DHCP is enabled.
Print Server: Enter the Print Servers IP address to enable the Print Image operation (Function and
Zoom).
TCP MTU Size: Select from Standard, 1400, and 1200. The MTU describes the maximum possible TCP
packet size. Standard (1500) is optimal for most ethernet network environments.
0150-0193F
58
Kalatel DVMRe Triplex
3.18 Front Panel Lock
Use this feature to lock the front panel keypad. While locked,
the only operational key on the front panel is the Menu button.
To unlock the front panel, enter the Installer password and return
to this menu.
Unlock Keyboard
Lock Keyboard
Highlight the item you wish to select.
Save changes and exit the menu: Press the Enter button.
Exit the menu without making changes: Press the Menu button.
3.19 Factory Settings
Return To Factory Defaults
From the Factory Setting menu, press the Enter button. A
password box will appear. Enter the Factory Default password.
Select OK, then press the Enter button.
The unit will reboot, returning all settings (except the time and date)
to the factory defaults. Due to the large size of the hard disk, the
reboot may take several minutes.
Factory Default Password
10 and 16-Channel
8111
4-Channel
4111
Change Language
From the Factory Setting menu, press the Enter button. A
password box will appear. Enter the Language password. Select
OK, then press the Enter button.
A menu will appear displaying the available language selections.
Rotate the Jog to select the desired language.
Language Password
10 and 16-Channel
5415
4-Channel
1414
Save changes and exit the menu: Press the Enter button.
English
Exit the menu without making changes: Press the Menu button.
French
German
3.20 Passwords
Installer Password
Use this feature to change the Installer, Operator or Ethernet passwords.
Operator Password
Ethernet Password
Changing the Installer or Operator Passwords
To change the password:
1. Highlight the password you wish to change, then press the
Enter button. A password box will appear.
2. Enter the new password using the Number buttons.
3. Highlight OK, then press the Enter button.
4. Re-enter the password.
Password Box
Enter a new Install Password
----
5. Highlight OK, then press the Enter button. The user will be
prompted, indicating if the password was entered correctly
and changed.
0150-0193F
59
Kalatel DVMRe Triplex
The Ethernet Password
The Ethernet Password feature limits access to only those
users who access the unit using the password feature of
WaveReader versions 2.3 or later. When the unit is first setup,
the default is No Password Protection. Meaning, anyone
using WaveReader and accessing with an ethernet connection
can connect to the unit.
Password Box
Enter a new Ethernet Password
----
Activate The Ethernet Password
1.
2.
3.
4.
Enter the new password using the Number buttons.
Highlight OK, then press the Enter button.
Re-enter the password.
Highlight OK, then press the Enter button. The user will be prompted, indicating if the password was
entered correctly and changed.
Deactivate The Ethernet Password
To return the unit to No Ethernet Password Protection,
enter the Ethernet Access Reset Password in the
password box shown above.
Ethernet Access Reset Password
1 1 1 1
3.21 The QuickInstall Menu
QuickInstall Menu Overview
After installation is complete, it is strongly recommended that, as
a minimum, the items in the QuickInstall menu be configured
before the unit is used.
All items located in the QuickInstall menu are also found in the
Main menu. These items are provided in the separate QuickInstall
menu as a convenience for the installer.
Use the following table to find detailed information about configuring
specific items from the QuickInstall menu.
QuickInstall Menu Item
Change the time
Change the date
Edit Camera Titles
Camera Disable
Record Quality
Installer Password
Auto Disable Now
Primary Menu Location
Section In
Manual
Change the time
Main Menu → Time/Date → Set Time
3.8
Change the date
Main Menu → Time/Date → Set Date
3.8
Edit Camera Titles
Main Menu → Camera Setup → Camera Titles
3.14
Camera Disable
Main Menu → Camera Setup → Camera Disable
3.14
Record Quality
Main Menu → Record → Record Quality
3.10
Installer Password
Main Menu → Passwords → Installer Password
3.20
Auto Disable Now
Main Menu → Camera Setup → Camera Disable
→ Auto Disable Now
3.14
0150-0193F
60
Kalatel DVMRe Triplex
3.22 The Operator Menu
The Operator Menu Overview
Sequencing
The Operator menu is provided so that the user has access to a
limited number of menu items. These menu items are primarily
monitor display setup options, so that the user may “personalize”
the monitor displays during their shifts. Other options include video
archive setup and changing the operator password.
None of the items are unique to the Operator menu. All items
located in the Operator menu are also found in the Main menu.
Time/Date Display
Titles Display
Alarm History
Archive Setup
Operator Password
Use the following table to find detailed information about configuring specific items from the Operator
menu.
Operator Menu Item
Primary Menu Location
Section In
Manual
Sequencing
Main Menu → Sequencing
3.9
Time/Date Display
Main Menu → Time/Date → Time/Date Display
3.8
Titles Display
Main Menu → Camera Setup → Camera Titles →
Title Display
3.14
Alarm History
Main Menu → Alarm → Alarm History
3.11
Video Archive Setup
Main Menu → Archive Setup
3.15
Operator Password
Main Menu → Password → Operator Password
3.20
3.23 The SystemView Menu
About DVMR
The SystemView Menu Overview
View Screen 1
The SystemView menu is provided so that users may quickly view global
software and hardware settings.
View Screen 2
View Screen 3
View Screen 4
View Screen 5
View Screen 6
View Screen 7
View Screen 8
View Screen 9
0150-0193F
61
Kalatel DVMRe Triplex
About DVMR menu: This menu provides information
such as:
•
Model Designation
•
•
•
•
•
Serial Number
Hostname
Software Version
Software Date
Boot Code Version
•
•
•
•
Hard Disk Size
IP Address
Hardware Address (MAC).
DHCP Lease Expiration Date
Model:
Serial Number:
Hostname:
Software Version:
Software Date:
Boot Code Version:
Disk Size:
IP Address:
Hardware Address:
DHCP Lease Expires:
DVMRe-16CT
D406-T2-250419
D406T2250419
VER 5.00
Mar 25 2003 16:40:18
VER 1.03
163.93 GB
3.18.173.10
BA-BE-C6-7E-FA-CE
No Lease or Date
OK
View Screens 1 through 9: These menus provide an overview of the units current operating
parameters and the menu settings selected by the user or installer. Each View Screen is described in
the following tables. The default values are bolded and italicized.
The View Screens
View Screen 1
Alarm Input
• Enable/Disable: 1 = Enabled, 0 = Disabled
• Normally Open or Normally Closed: 0 = Open, C = Closed
• Macro: Macro number if activated.
Alarm Action
• Freeze: 1 = Freeze, 0 = No Freeze
• Cameras: Primary camera in alarm and three associated cameras.
• Relay: 1, 2, 1+2, or None.
• Intrusion AND/OR: AND, OR
View Screen 2
Camera
• Enable/Disable: 1 = Enabled, 0 = Disabled
• Signal Gain: AGC setting from 1 through 100. 50
• Covert Camera: Yes or No
• Camera Title: Camera x, x=number
Videoloss Action
• Relay 1: 1 = Enabled, 0 = Disabled
• Relay 2: 1 = Enabled, 0 = Disabled
• Buzzer: 1 = Enabled, 0 = Disabled
0150-0193F
62
Kalatel DVMRe Triplex
View Screen 3
Motion Detection
• Enable/Disable: 1 = Enabled, 0 = Disabled
• Activity or Intrusion Detection: I = Intrusion, A = Activity
• Sensitivity: 1 through 10, 5
• Relay Output: None, 1, 2, 1+2
• Link to Event: Yes or No
• Rejection Ratio: High, Medium, or Low
• Target Size: 1 through 256
• Alarm Camera: 1 through 4, 10 or 16
View Screen 4
Record Rate
• Event Camera Settings: T = Timelapse, E = Event, ET = Event and Timelapse
• Timelapse Record Rate: In pictures per second (pps). 30 spp
• Event Record Rate: In pictures per second (pps). 1 pps
• Pre Event Duration: 0 to 5 seconds. 2
• Post Event Duration: 0 to 200 seconds. 0
• Acitvity Record Rate: In pictures per second (pps). 2 spp
• Record Quality: High, Medium, or Standard.
• Event Associated Cameras: Up to 3.
View Screen 5
Record Timer
• DAY: 1-31, Mon, Tue, Wed, Thu, Fri, Sat, Sun, Mon-Fri, Sat-Sun, Mon-Sun
• Start: Time (HH:MM)
• Stop: Time (HH:MM)
• Macro: Macro Number
• On/Off: On or Off
View Screen 6
•
•
•
•
•
•
•
•
•
Time and Date Display A: On or Off.
Time and Date Display B: On or Off.
Time Format: 12 or 24 hour
Date Format: MM/DD/YY, DD/MM/YY, or YY/MM/DD
Master Clock: Yes or No.
Multiscreen Dwell: In seconds. 003
Full Screen Dwell: In seconds. 003
Titles Display A: On or Off.
Titles Display B: On or Off.
0150-0193F
63
Kalatel DVMRe Triplex
View Screen 7
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Record Mode: No Overwrite, Write Once, or Continuous.
Indicate Detection: On or Off.
Global Buzzer: On or Off.
Live Alarm Buzzer: On or Off.
Video Loss Buzzer: On or Off.
Playback Buzzer: On or Off.
Relay 1: Normally Open or Normally Closed.
Relay 2: Normally Open or Normally Closed.
Alarm Latch: T = Transparent, L = Latched, TO (020) = Timed Out (Time)
Alarm Record Mode: Interleaved, Exclusive, or No Change.
Full Screen Alarm: Yes or No. This feature is not selectable on the 4-Channel units. 4ch = Yes.
Global Alarm Record Rate: In pictures per second (pps). 30 pps
Pre Alarm Duration: In seconds. 001
Archive Alarm: Enable or Disable.
View Screen 8
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Auto Disable: On or Off.
Background Archive: On or Off.
Monitor Setup: Single or Dual.
Baud Rate Port 1: 1200,1400, 4800, 9600, 19200, 38400, and 57600.
Baud Rate Port 2: 1200,1400, 4800, 9600, 19200, 38400, and 57600.
Network Address: 001-005. 001
Ethernet: Enable or Disable.
POTS: Enable or Disable.
Language: English, German, or French.
Keyboard Lock: On or Off.
Record Lock: On or Off.
Regional Settings: Off, USA, EUR, and AUS.
Time Zone: GMT+00:00
QuickWave CD Write: On or Off.
View Screen 9
•
•
•
•
•
•
•
•
•
•
•
NTP Update Interval: Enable or Disable.
NTP Primary Server: 3. 37. 8. 26
NTP Backup Server: 0. 0. 0. 0
Subnet Mask: 255.255.254. 0
Gateway: 3. 18.172. 1
DHCP: Enable or Disable.
Name Service: WINS or Disable.
Primary Name Server: 3. 18.173. 12
Backup Name Server: 3. 18.173. 13
Print Server: 3. 18.173. 11
TCP MTU Size: Standard, 1200, and 1400.
0150-0193F
64
Kalatel DVMRe Triplex
4 Alarms
4.1 Alarm Input
Alarm devices are connected via the Alarm PCB on the back panel of the unit (see section 1.7). Each
Alarm Input corresponds with the Camera Input of the same number. Alarm input to camera number
assignments can be changed on 10 and 16-channel models. See Alarm Action menu (section 3.11).
4.2 Alarm Output
Front Panel Alarm LED: The LED located to the left and above the Alarm button is lit for the duration
of the alarm.
Internal Buzzer: The internal buzzer is activated until it is Silenced and Acknowledged. This feature
can be turned off in the menu system (see Buzzer Setup in section 3.11).
Monitor Displays: Discussed below in the On-screen Displays During Alarms section.
Output Relays: The alarm output relays are active for the duration of the alarm. This feature is
configured in the menu system (see Alarm Action and Relay Configuration in section 3.11) and can be
deactivated.
Macro Activation: Unit can be configured in the menu system to activate a macro when an alarm is
detected.
Preset PTZ Camera commands: Unit can be configured in the menu system to send preset
commands to specific cameras when an alarm is detected.
Record Rate: Record Rate can be increased by recording at the Alarm Record Rate (see section
3.10) and by Interleaved or Exclusive Recording (see Alarm Record mode in section 3.11).
4.3 Alarm Acknowledge
Pressing the Alarm button acknowledges to the unit that the alarm has been recognized and silences
the internal buzzer. This does not clear the alarm condition.
4.4 On-screen Displays During Alarms
10 and 16-Channel Units
Monitor-A in Live Multiscreen Mode
Single Alarm: When a single alarm is received, the unit changes to 4-way
display containing the camera in alarm, and three associated cameras. The three
associated cameras are defined as a group in the menu system (see Alarm
Action in section 3.11). The top left cameo displays the camera in alarm.
4-Way
Single Alarm
Second Alarm: When a second alarm is received, the unit changes to a 10-way
multiscreen, displaying the alarm cameras in the top two cameos. The
associated cameras are displayed in the remaining cameos.
10-Way
Second Alarm
Third Alarm: When a third alarm is received, the unit changes to a 9-way
multiscreen, displaying the alarm cameras in the top three cameos. The
associated cameras are displayed in the remaining cameos.
More than three alarms simultaneously: The unit switches to the maximum
multiscreen display, i.e. 16 or 10-way.
0150-0193F
65
9-Way
Third Alarm
Kalatel DVMRe Triplex
Other display options include:
•
A full screen display of a single camera in alarm, with a sequenced full screen display for
additional cameras in alarm. This option is selectable in the menu system (see Full Screen Alarm
in section 3.11).
•
Freeze camera display at the time the alarm was received.
Monitor-B Display During Alarm
Single Alarm: Unit switches to a full screen display of the camera in alarm.
Additional Alarms: Unit switches to a sequenced display of all cameras in alarm.
4-Channel Units
Single Alarm: Unit switches to a full screen display of the camera in alarm.
Additional Alarms: Unit switches to a sequenced display of all cameras in alarm.
4.5 Alarm Operations During Playback
Live Alarms Displays
Single Alarm: Unit switches to a full screen display of the camera in alarm on Monitor B.
Additional Alarms: Unit switches to a sequenced display of all cameras in alarm on Monitor B.
LIVE MODE
PLAYBACK MODE
Monitor A
Monitor B
Monitor A
Monitor B
LIVE
LIVE
PLAY
BACK
LIVE
LIVE ALARM
A
LIVE
0150-0193F
LIVE ALARM
FULL
SCREEN
ALARM
66
LIVE ALARM
PLAY
BACK
LIVE ALARM
FULL
SCREEN
ALARM
Kalatel DVMRe Triplex
Recorded Alarms
Internal Buzzer: During playback, the internal buzzer is activated until it is silenced and
acknowledged. This feature can be turned off in the menu system (see Playback Buzzer, Buzzer
Setup in section 3.11).
Front Panel Alarm LED: The LED located to the left and above the Alarm button is lit for the duration
of the alarm.
Monitor-A Multiscreen: Each camera in alarm is indicated on-screen by a flashing red “A” in its
cameo. Alarm LED lights to indicate an alarm condition. There is no change in the playback (or
Triplex) multiscreen based on playback of recorded alarms.
4.6 Alarm History Box
The Alarm History feature provides a list of the 100 most recent alarms. View the Alarm History Box
by accessing the menu system, and selecting Operator → Alarm History. The Alarm History Box
can also be found under Main Menu → Alarm → Alarm History. For detailed information about
viewing the Alarm History Box see Alarm History in section 3.11.
4.7 Searching For Recorded Alarms
See section 5.
0150-0193F
67
Kalatel DVMRe Triplex
5 Searching
The Kalatel DVMRe Triplex is equipped with a powerful search interface to access video files stored
on the hard disk or an external archive device.
Search Menu Overview
Search
Button
Disk Analysis Screen
Disk Analysis Screen
Search Filters
Motion Search
01/21/2002 20:17:01
Search
Button
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Search Filters
Motion Search
X
Operation:
Last 2hrs
Last 8hrs
Last day
Last 7 days
Last 4 weeks
Last 12 weeks
Custom
Search
Button
Play from Disk
DATE (MM/DD/YY)
TIME (HH:MM)
Start
Stop
Start
Stop
01/27/02
01/27/02
20:57
20:59
Activity
Event
Text
Alarm
Camera
Enter
Alarm
Event
Activity
Videoloss
Present
Hit SEARCH again to enter Advanced Search
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
[CANCEL]
[START SEARCH]
Absent
Level 1
CAMERA key selects/deselects individual camera
Activity Setup
ZOOM key selects/deselects
(except 1) all cameras
Search
Button
Enter
Enter
Enter
Search Results
Time/Date Search Results
Play Back
Activity, Text, Motion, Alarm Search Results
Search Results
Search Results
000
9
Start Date
Start Time
Days HH MM SS
01/21/2002
20:07:10
0 04:35:15
001
01/21/2002
20:08:10
0 00:01:55
002
01/21/2002
20:09:10
0 00:00:38
3/19 06:11 3/19 21:42 3/19 23:51 3/20 6:26 3/20 14:30
003
01/21/2002
20:10:10
0 01:07:22
02
004
01/22/2002
20:07:10
0 00:00:07
005
01/23/2002
20:07:10
0 00:08:56
006
01/24/2002
20:07:10
0 00:00:06
007
01/25/2002
20:07:10
0 05:57:31
008
01/26/2002
20:07:10
0 00:46:43
matches found.
02
02
02
3/20 18:51 3/20 21:54 3/21 02:25 3/21 03:51 3/22 21:01
02
10
‘PLAY REV/FWD’ to page up/down
‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.
02
02
02
02
02
matches found.
‘PLAY REV/FWD’ to page up/down
‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.
Enter
Play Back
0150-0193F
68
Kalatel DVMRe Triplex
5.1 Disk Analysis Screen
Begin by pressing the Search button. The Disk Analysis Screen will appear.
This screen shows a graphical representation of the recorded video stored on the
internal hard disk.
Search Button
02/28/2002 20:45:00
Arrow Cursors
Disk Analysis Screen
01/21/2002 20:17:01
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Disk Time
and Date
at cursor
location.
Record
Button
Alarm
Event
Activity
Videoloss
Present
Hit SEARCH again to enter Advanced Search
Write to CD
Absent
Level 1
Zoom
Level
Rotating the Jog moves the two arrow cursors across the representation of the recorded video. As the
cursors move across the screen the corresponding disk time is indicated in the upper right of the screen.
The video representations are color-coded by category. Rotating the Shuttle expands (Zooms) the
display. The Lowest level (most detail) is indicated on screen with an (L). Pressing the Enter button will
start Playback from the cursor location.
5.2 Quick Archive to CD
Archive to CD on the Disk Analysis Screen by selecting the time and date and pressing the record
button. The QuickWave Setup must be set to ON from the Archive Setup → Quick Wave Setup menu
(see section 3.15). The Archive Incident menu should appear.
Archive Incident
1. Use the Jog to modify the time parameters and use the
Shuttle to move between the Start and Stop fields.
07/31/2003
2. Press the Record button on the front panel when satisfied.
02:02:51P
Start
02:20:06P
Stop
02:20:09P
3. The CD Writer will open the CD tray when completed.
Capacity: 557MB
The video may now be viewed on any PC equipped with a CD-ROM.
0150-0193F
69
‘RECORD’ to Archive
Kalatel DVMRe Triplex
5.3 Motion Search
Pressing the Search button a second time will bring up the Motion Search menu. This menu performs a
motion search with six preset time parameters and a custom search option. Rotate the Jog to navigate
and the Shuttle to select a specific parameter. Selecting the Custom option and pressing the Enter
button starts playback and brings up another window with Start/Stop, Time/Date options. These options
provide the parameters to focus the search to a specific time period.
Motion Search
X
Last 2hrs
Last 8hrs
Last day
Last 7 days
Last 4 weeks
Last 12 weeks
Custom
Selecting any of the other options and pressing Enter starts playback and displays the Motion Search
Setup Screen.
5
This screen overlays the current playback video and allows the user to enable or disable motion
detection on the screen within blocks that form a 16 x 16 grid.
Pressing the Function key while in this screen overlays a help screen with all the available
commands.
{F}
Function
Button
0150-0193F
‘MENU’ :
‘ENTER’:
‘PAUSE’:
‘STOP’ :
‘ZOOM’ :
Exit Activity Setup
Save and Exit Activity Setup
Toggle between Enable and Neutral
Toggle between Disable and Neutral
Disable/Enable all zones
70
Kalatel DVMRe Triplex
Pressing Enter upon completion of the activity setup will start the search and launch the Search
Results window. See section 5.4 for operating instructions.
5.4 Search Filters
Pressing the Search button a third time brings up the Search Filters Menu. Use the Search Filters menu
to specify:
•
The type of operation to be performed: Play from Disk, Play from Archive, Copy from Disk to
Archive, and Copy from Archive to Disk.
•
The Start and Stop date of the search.
•
The Start and Stop time of the search.
•
Searching for recorded activity, events, or alarms.
•
Searching for a text string.
•
Which cameras to search inclusively or exclusively.
Search Filters
Operation:
Play from Disk
The following options are
available when an archive
device is connected:
DATE (MM/DD/YY)
TIME (HH:MM)
Start
Stop
Start
Stop
01/27/02
01/27/02
20:57
20:59
Activity
Event
Text
Alarm
1. Play from Disk.
2. Play from Archive.
3. Copy from Disk to Archive.
4. Copy from Archive to Disk.
Selecting these functions
displays thumbnails in
the Search Results window.
Camera
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
[CANCEL]
[START SEARCH]
X
Hit Camera buttons to
select/deselect individual
cameras. Use the Zoom
button to globally
select/deselect cameras
to search.
CAMERA key selects/deselects individual camera
ZOOM key selects/deselects
(except 1) all cameras
Selecting Search Parameters
1. Rotating the Jog to navigate, highlight the box adjacent to the parameters that you wish to modify.
2. Once in the Parameter Box, use the Shuttle to navigate through the fields and the Jog to change
the values.
3. To activate the parameter, use the Shuttle or the Enter button to place an [X] in the check box.
4. When finished, use the Jog to navigate to another parameter.
0150-0193F
71
Kalatel DVMRe Triplex
5.5 Search Results
Activate Search
From the Search Filters menu, use the Jog to navigate to the Start Search parameter. With the Start
Search parameter highlighted, press the Enter button to begin the search operation. When finished
searching, the Search Results window will appear. A maximum of 200 results can be displayed per
search. Two types of Search Result windows will appear depending on the type of search that is
performed.
Activity, Text, Motion, Alarm Search Results
Time/Date Search Results
Search Results
Search Results
Start Date
Start Time
Days HH MM SS
000
01/21/2002
20:07:10
0 04:35:15
001
01/21/2002
20:08:10
0 00:01:55
3/19 06:11 3/19 21:42 3/19 23:51 3/20 6:26 3/20 14:30
002
01/21/2002
20:09:10
0 00:00:38
02
003
01/21/2002
20:10:10
0 01:07:22
004
01/22/2002
20:07:10
0 00:00:07
005
01/23/2002
20:07:10
0 00:08:56
006
01/24/2002
20:07:10
0 00:00:06
007
01/25/2002
20:07:10
0 05:57:31
008
01/26/2002
20:07:10
0 00:46:43
02
02
02
02
3/20 18:51 3/20 21:54 3/21 02:25 3/21 03:51 3/22 21:01
02
10
02
02
02
02
matches found.
9
‘PLAY REV/FWD’ to page up/down
‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.
matches found.
‘PLAY REV/FWD’ to page up/down
‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.
Follow the directions on-screen to select, archive, playback, etc.
Search Results
3/19 06:11 3/19 21:42 3/19 23:51 3/20 6:26 3/20 14:30
02
02
02
02
02
3/20 18:51 3/20 21:54 3/21 02:25 3/21 03:51 3/22 21:01
02
10
02
02
02
02
matches found.
‘PLAY REV/FWD’ to page up/down
‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.
Some options may be unavailable depending on the type of search performed. These options are not
displayed. When archiving, the unit will not allow the amount of selected data to exceed the amount of
space available on the target medium.
Press the Menu button to exit the Search Results window without making a selection.
Hitting the Enter button will play the selected search result.
Hitting the Enter button again while in playback will cause the next selection from the search list to be
played.
Press the Sequence button to repeatedly play the selected event.
0150-0193F
72
Kalatel DVMRe Triplex
6 WebBrowser
The DVMRe Triplex has an integrated WebBrowser interface. The WaveBrowser option allows the user to
view video from any ethernet connected Triplexes with software version 4.09 or above.
NOTE
For WaveBrowser to function properly, certain ActiveX controls must be set correctly. To
setup the ActiveX controls:
1. Click on the Tools → Internet Options Menu in Internet Explorer.
2. Click on the Security tab.
3. Select Local Intranet for the Web Content Zone.
4. Click on the Custom Level button.
5. Ensure that both Download unsigned ActiveX controls and Initalize and Script
ActiveX controls not marked as Safe are set to Prompt.
6. Click the OK button.
7. Click on the Yes button in the Warning message.
8. Click the OK button in the Internet Options window.
To access the web interface:
1. Launch Internet Explorer (version 5.5 or later) on any local Internet connected PC or laptop.
2. Type in the Triplex’s IP address or hostname in the address field and press enter. The Enter
Network Password box should appear.
3. Enter the correct Username and Password in their respective fields (the default username and
password is admin). Click the OK button.
4. The WaveBrowser window should appear. Type the IP address in the IP Address Field and click
the Connect button.
IP Address Field
0150-0193F
73
Kalatel DVMRe Triplex
6.1 WaveBrowser Overview and Controls
Button Panel
Main Viewing
Area
Drop Down
Volume List
The Main program window consists of the following areas:
•
The Main Viewing Area: The large blue area.
•
The Button Panel: The left side of the window.
•
The Drop Down Volume List: Allows the selection of available Disk volumes.
The Main Viewing Area
Pictures are displayed in this area in Multi-Camera, and Single-Camera formats. Picture display order
is according to the information encoded by the unit used to create the original video data file.
Choose from the following displays:
•
•
16-way Multiscreen Display (Large and Medium)
4-way Display
•
•
Single Camera Display Large
Single Camera Display Medium
•
Single Camera Display Small
0150-0193F
74
Kalatel DVMRe Triplex
The Button Panel
1
1. Play Backward button: Click on this button to playback video in
reverse.
2
3
5
2. Stop button: Click on this button to halt all playback operations. The
Play Pointer Slider Bar moves to the start of data.
3. Play Forward button: Click on this button to playback video.
4
6
7
8
9
4. Single Frame Rewind button: Click on this button to rewind the video a
single frame.
10
5. Pause button: Pauses playback until the Pause button is pressed
again. Clicking any of the buttons, except Stop will also resume
playback. The Play Pointer slider bar stays at the current position while
paused.
13
6. Single Frame Advance button: Click on this button to advance the
video a single frame.
14
16
7. Rewind button: Click on this button to perform high-speed reverse
playback.
18
19
9. IP Address Field: Enter the unit’s IP address.
20
10. Password Field: Enter the unit’s password, if necessary.
21
11. Live check box: Click in this box to enable live viewing before connecting.
12. Connect/Disconnect button: Click on this button(s) to connect to the unit.
13. Number buttons: Press any of these buttons to call up individual cameras for display. When
connected to a unit that has more than 16 cameras, right-clicking over the number buttons will
display numbers 17 through 32. Right-click again to return to cameras 1 through 16.
14. Single Camera Display Size: Choose from Small, Medium, or Large.
15. 16-way Multiscreen button: Choose from a Medium 16-way, or Large 16-way.
16. 4-way Multiscreen button: Selects a Large 4-way display.
17. View Live Button: Click on this button while connected to view live video.
18. Play Pointer Slider Bar: The Play Pointer slider bar advances to the right to indicate the
playback position on the disk. The user can drag the bar to navigate forward or backward.
19. Goto Button: Click on this button to go to the selected date for the drop down time and date
boxes.
20. Drop down Date Selection Menu: Click on this field to display a graphic calendar to select a
date to view.
21. Time Selection Menu: Click on the Up or Down Arrows to select a specific time to view.
The Drop Down Volume List Box
Click on the arrow to display a list of available disk volumes on the connected unit. Click on the volume
to select.
75
15
17
8. Fast Forward button: Click on this button to perform high-speed
playback.
0150-0193F
11
12
Kalatel DVMRe Triplex
6.2 DVMRe Triplex WaveLink
A new feature with Triplex software version 5.00 is the DVMRe Triplex WaveLink. This feature allows
putting command codes in the URL when calling WaveBrowser to control actions the WaveBrowser is
going to perform.
This feature can be used by Web Developers to link various cameras to specific Web content. It will
also be used by the DVMRe Email feature to allow the recipient of an alarm email to click on a link in
the email, which causes the WaveBrowser to connect and play back at the time when the alarm
occurred.
Functionality
The traditional WaveBrowser URL is http://<IP_Address>/wrcontrollite.ssi. This URL will start the
WaveBrowser in the disconnected state. Triplex software version 5.00 supports command codes
placed after an underscore after wrcontrollite and before .ssi. In the following example, the options
are in bold.
Example: http://3.18.172.230/wrcontrollite_c=1s=2a=3t=1361959858.ssi.
The following table specifies the supported options:
Name
Code
Description
Example
Camera
c=<n>
Describes either the camera number for
fullscreen (1=Camera 1, …16=Camera
16) or the type of the multiscreen display
(100 = Multiscreen 16 large, 101=
Multiscreen 16 small, 102= Quad
screen)
c=10
Size
s=<n>
For fullscreen camera, describes the
size of the display (1=large, 2 =medium,
3= small)
s=2
Action
a=<n>
Describes the action the WaveBrowser
has to take:
a=2
0 No action
1 Normal Connection Play
2 Normal Connection Live
3 Normal Connection Goto
4 Live Connection
Time
NOTE
0150-0193F
t=<n>
When action is set to 3 (Goto), the time
specifies where to go in number of
seconds since 01/01/1960.
t=1361959858
Please Note: When an option is not specified, it will be set to 0.
When a normal connection is requested, but the DVMRe unit is already connected via a
normal connection, the WaveBrowser should open a live connection instead.
76
Kalatel DVMRe Triplex
The default page, http://3.18.172.230, does not accept option codes and will open the WaveBrowser in
disconnected state.
The example URL from above (http://3.18.172.230/wrcontrollite_c=1s=2a=3t=1361959858.ssi)
requests the WaveBrowser to make a normal connection, play back at 2/27/2003 10:53:32
displaying camera 1 in medium size.
Email Links
The DVMRe Triplex is able to send emails when certain events occur (like videoloss, alarms, etc.).
When in record mode, the Triplex software version 5.00 will add a WaveBrowser link in the email
notification.
Clicking this link initiates WaveBrowser to be started, make a normal connection and play back the
specific camera with a medium size video window at the time the event occurred.
0150-0193F
77
Kalatel DVMRe Triplex
7 Technical Specifications
General
External Power Supply
12 Volt DC. 60 Watt (5 Amp)
Connector
2.1mm barrel connector, center positive.
Power Consumption
35 Watt nominal (single hard disk).
Operating Temperature Range
Operating: 0 to 40°C. Storage: -20 to +60°C.
Relative Humidity Range (Non-Condensing)
Operating: 10% to 80%. Storage: 10% to 95%
Dimensions
17.5 x 14 x 1.7 Inches. 1U, 19 inch rack unit.
Weight
9 Lbs.
Connections
10/100 Ethernet Port
RJ-45 Connector.
RS232 Port 1
DB-9 Male Connector.
AUX Port
DB-9 Male Connector.
RS232 Port 2
RJ-45 Connector.
Camera Inputs
BNC connectors. Auto Terminating. Color & Mono.
Monitor-A Output (Y/C)
4-pin Mini-DIN Connector.
Monitor-B Output (Y/C)
4-pin Mini-DIN Connector.
Monitor-A Output (Composite)
BNC Connector.
Monitor-B Output (Composite)
BNC Connector.
RS485 Port
Two Looping RJ-45 Connectors
SCSI Port
50 pin, High Density SCSI-2 female connector.
IEEE 1394 Firewire Port
6 position SMT IEEE 1394 Socket
Alarm I/O Port
Use Supplied DB-25 PCB connector.
Video
Video Signal Input
0.5 to 2.0 Volts peak-to-peak with Automatic Gain Control.
Video Signal Output
1 Volt peak-to-peak into 75-Ohm.
Input Termination
75-Ohm (Auto Terminating)
Display Memory
4 Megabytes
Resolution
Horizontal: 720 Pixels. Vertical: 484 Lines (576 for PAL).
Gray Scale
256 levels
Colors
Y:U:V 4:2:2, 16.8 Million Colors
Compression Standard
Wavelets
0150-0193F
78
Kalatel DVMRe Triplex
Audio
Audio Input
315mV, 40k Ohms. Unbalanced.
Audio Output
315mV, 600 Ohms. Unbalanced.
Alarms
Inputs
1 per camera.
Relay Configuration
User programmable as Normally Open or Normally Closed.
Record Priority
Interleaved, Exclusive, or No Change.
Alarm Status Indicators
Relay Outputs, On-screen Indicators. Status Retrievable via RS232
port.
Motion Detection
Zones Per Camera
256: 16 x 16 grid.
Sensitivity Settings
10 levels
Gray Levels Per Zone
256 levels
Motion Detection Status
Output
Relay Outputs, Link to Alarms, Link to Events, On-screen Indicators.
Status retrievable via RS232 port.
Part Numbers
Remote Keyboard
CBR-KB3, CBR-KB3/J, KTD405. Includes motorized pan, tilt, and zoom
controls.
Rack Mount Kit
CBR-RK6. 1U Height. Part Number: 0110-R601
Replacement Manual
0150-0193
0150-0193F
79
Kalatel DVMRe Triplex
8 RS232 Event Generation/Text Insertion Protocol
8.1 Message Structure
The Delimiter byte signals the start of a new message, and has a value of 0xFF.
Delimiter
The Class and Command fields identify the type of message.
Class
The Data Length is a 16-bit value indicating the number of bytes in the Data portion of
the message. Data Length is sent using Intel byte ordering (Little Endian).
Command
Data Length
The Check Sum byte is the result of XORing all the bytes in the message.
Data
Check Sum
8.2 Message Type
One message is currently supported to store text along with recorded video.
0xFF
CMD_NEW_ADD_TEXT
0x14
Class byte is 0x14.
0x40
Command byte is 0x40.
Data Length[0]
Data Length is the number of data bytes in the message (from 2 to 502).
Data Length[1]
Camera byte indicates the camera associated with the text. The valid range is from
0 to 15.
Camera
Event
Alarm/Event byte usage is described in the following section.
String[0]
String field contains text characters. The string can be from 0 to 500 characters in
length.
String[1]
:
String[n-1]
Check Sum
8.3 Alarm/Event Field
The two least significant bits are currently used for the
event. Bits 2 and 3 are used for Alarm
MSB 7
0
LSB 0
0
0
0
A
A
E
E
A – Alarm/Event 0x00
If both the start and end bits are clear, the associated text will be stored with the next recorded field for
that camera. That cameras record rate will not be changed.
B – Alarm/Event 0x01
If only the start bit is set, the associated text will be stored with the next recorded field for that camera.
This will cause the selected camera, as well as any pre-event fields to be recorded at the Alarm or
Event Record Rate.
C – Alarm/Event 0x02
If only the end bit is set, the associated text will be stored with the next recorded field for that camera.
This will start the post-event timer** after which, the selected camera will resume recording at the
normal record rate*.
0150-0193F
80
Kalatel DVMRe Triplex
D – Alarm/Event 0x03
If both the start and end bits are set, the associated text will be stored with the next recorded field for
that camera. The post-event timer will be started** after which the selected camera will resume
recording at the normal record rate*.
**If enabled.
0150-0193F
81
Kalatel DVMRe Triplex
9 RS232 Remote Control Protocol
The unit supports two different communication types:
• Remote Front Panel Button Emulation
• Remote Configuration and Status
9.1 Front Panel Button Emulation
Data Structure
Byte 1: 0xFF
Byte 2: 0x55
Byte 3: Front Panel Button Code
Description
Byte 1 and 2 are header bytes.
Byte 3 contains the code for a specific front
panel button.
The different buttons and their corresponding
codes are as follows.
No Button Pressed
0
Record
1
Play
2
Stop
3
Alarm
4
Freeze
5
Zoom
6
Sequence
7
Reserved
8
Camera 1
9
Camera 2
10
Camera 3
11
Camera 4
12
Camera 5
13
Camera 6
14
Camera 7
15
Camera 8
16
Camera 9
17
Camera 10
18
Camera 11
19
Camera 12
20
Camera 13
21
Camera 14
22
Camera 15
23
Camera 16
24
Reserved
25 - 40
Menu
41
Enter
42
Reserved
43
Macro
44
Reserved
45-49
0150-0193F
82
Monitor B
Reserved
Left Arrow
Right Arrow
Up Arrow
Down Arrow
Reserved
Alarm and Sequence
*Alarm and Camera 1
*Alarm and Camera 2
*Alarm and Camera 3
*Alarm and Camera 4
*Alarm and Camera 5
*Alarm and Camera 6
*Alarm and Camera 7
*Alarm and Camera 8
*Alarm and Camera 9
*Alarm and Camera 10
*Alarm and Camera 11
*Alarm and Camera 12
*Alarm and Camera 13
*Alarm and Camera 14
*Alarm and Camera 15
*Alarm and Camera 16
Reserved
Search
Frame Reverse
Frame Forward
Play Reverse
Stop
Play Forward
Monitor A
2 Way Multiscreen
4 Way Multiscreen
6 Way Multiscreen
7 Way Multiscreen
9 Way Multiscreen
10 Way Multiscreen
13 Way Multiscreen
16 Way Multiscreen
50
51-63
64
65
66
67
68-74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92-110
111
112
113
114
115
116
130
131
132
133
134
135
136
137
138
*Must send a “No Button Pressed” command
immediately following any of these
commands.
Kalatel DVMRe Triplex
9.2 Configuration and
Status
iii) Requesting data from the DVMRe
i) Data structure
When a message of type 0xBB is sent to the
DVMRe Triplex, it will respond by sending 16
bytes of requested data.
Byte 1: 0xFF
Byte 2: Command Type
0xAA: (SET) Update DVMRe with data.
0xBB: (GET) Extract data from DVMRe.
Byte 3: Data Length (n)
Byte 4: Data Type
0x61: Restart DVMRe
0xFE: Send configuration data to DVMRe
0x09: Read Alarm History from DVMRe
0xFF: Read configuration and status data
from DVMRe
Byte 5: Data byte 1
Byte 6: Data byte 2
:
:
Byte x: Data byte n
a) Read Alarm History List
Byte 1: 0xFF
Byte 2: 0xBB
Byte 3: 0
Byte 4: 0x09
When the "Read Alarm History List" message is
received by the DVMRe Triplex, it responds by
sending a start byte 0xFF, followed by ASCII
strings for every alarm event in its alarm history
list, and a stop byte, 0xFF. Each string is
formatted as follows:
ii) Sending data to the DVMRe
a)
dd.bmm/ddbhh:mm:ssbaa<CR><LF>
Restart DVMRe Triplex
This command will restart the DVMRe Triplex.
dd:
b:
mm:
dd:
hh:
mm:
ss:
aa:
<CR>
<LF>
Byte 1: 0xFF
Byte 2: 0xAA
Byte 3: 0
Byte 4: 0x61
b)
Send data to DVMRe Triplex
Configuration data can be sent to the DVMRe
Triplex, to change the way it operates. The
data is arranged in the form of 16 byte blocks,
numbered from 1 to 213. Blocks 182, 183 and
185 are status blocks, and hence cannot be
written to. For details about the contents of
each block, contact GE-Interlogix and request
the Block Data Structure for the DVMRe
Triplex.
Byte 1: 0xFF
Byte 2: 0xAA
Byte 3: 17
Byte 4: 0xFE
Byte 5: Block Number
(1-181, 184, 186-213)
Byte 6: data[0]
:
:
:
:
Byte 21:data[15]
Example: 03. 11/27 22:48:58 15
b)
Read data from DVMRe Triplex
Configuration and status data can be read from
the DVMRe Triplex. The data is arranged in the
form of 16 byte blocks, numbered from 1 to 213.
For details about the contents of each block,
contact GE-Interlogix and request the Block
Data Structure for the DVMRe Triplex.
Byte 1: 0xFF
Byte 2: 0xBB
Byte 3: 1
Byte 4: 0xFF
Byte 5: Block Number 1-213 or 255 if all
blocks are requested.
After sending a block or series of blocks, block
number 255 must be updated to signal the end of
the configuration session. All data bytes for block
255 must be set to 0.
0150-0193F
index number (00 - 99)
space character
month (01-12)
day (01-31)
hours (00-23)
minutes (00-59)
seconds (00-59)
alarm number (01-16)
Carriage return (0x0D)
Line feed (0x0A)
83
The DVMRe Triplex responds to the “Read data”
request by sending all the requested data bytes
consecutively, without any start or stop bytes.
A total of either 16 bytes or 3408 bytes will be
transmitted, depending on whether a single block
or all the blocks were requested.
Kalatel DVMRe Triplex
10 Macro Tables
Photo copy this page and use it to keep a record of the programmed macro functions.
10.1 Macro Functions Table
Macro
Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Function +
Sequence
0150-0193F
Daylight Savings Time: Sets clock ahead one hour in April, and back one hour in
October.
84
Kalatel DVMRe Triplex
10.2 Scheduled Macro Table
Event
Day
Time
Macro to Run
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0150-0193F
85
Kalatel DVMRe Triplex
11 Warranty and Service
11.1 Factory Service
Warning: Do not open the top cover or attempt to service the unit, as this may expose
you to dangerous voltages and other hazards. Programmer maintenance of this unit is
limited to external cleaning and inspection. Refer all servicing to qualified personnel.
If the unit requires factory service, contact the dealer who supplied the unit to you for the correct
procedures on returning the unit to the factory or the nearest factory service center.
If the dealer is not available, contact the manufacturer of the unit as detailed below and request a
Return Material Authorization number (RMA). The unit’s serial number must be provided before a
RMA number can be issued. Units returned to the factory for service must have freight and insurance
prepaid, and must show the RMA number clearly on all shipping documents. The failure symptoms
must be clearly described by the operator and enclosed with the unit together with a copy of the
original suppliers invoice. Failure to comply with these instructions will delay service of the unit, and
may result in the unit not being accepted by the Repair Center.
Factory Address
GE-Interlogix, Kalatel Division
Attention: Repair Center
3197-C Airport Loop Drive
Costa Mesa, CA. 92626
United States of America
Telephone: 800-343-3358 (7:00 AM to 4:30 PM, Pacific Time)
In Oregon: 541-754-9133
Fax: 541-754-7162 (24 hours a day)
For warranty information, see the following page.
0150-0193F
86
Kalatel DVMRe Triplex
11.2 Warranty and Return Information
GE-Interlogix warrants all of its equipment for three years from the date of purchase. This warranty covers
any defects in materials and workmanship. Equipment failures that are due to improper installation,
modification, abuse, or acts of nature will not be covered by this warranty. The repair department will
evaluate all equipment returned for repair to determine warranty coverage. The Tech Support Manager
will resolve any questions that may arise during evaluation to make a final determination.
Note: The three-year warranty does not apply to the following products:
®
MobileView and the monitor CRT, which carry a 12-month warranty from the date of purchase.
The warranty specifically covers any defects in material and workmanship and does not cover equipment
that has been abused, damaged, or modified.
For all warranty repairs, GE-Interlogix will cover all costs, including parts, labor, and shipping. Repaired
equipment will be returned via the same method of shipment in which it was received. If a customer
requests a faster return shipment, the difference will be charged.
For all non-warranty repairs, the customer will be billed for parts, labor, and shipping. Labor will be
billed in half-hour increments.
Note: Customers requesting an estimate prior to repair will be notified by phone. If they cannot be reached, they will be notified by
fax. If we are unable to reach the contact person for repair authorization after one phone attempt and two fax attempts, the
equipment will be returned without being repaired. We will hold equipment no longer than two weeks.
Advance Replacement Policy
When an advance replacement is required, we will send the customer replacement equipment from our
stock and receive the returned product in exchange. The received equipment will be evaluated and the
repair department will determine whether it is a warranty replacement. If it is non-warranty, see our repair
policy above for details. The following guidelines will be used for all advance replacements:
• Fewer than 45 days from purchase, GE-Interlogix will replace the product with new equipment.
• From 45 days to 1 year from purchase, GE-Interlogix will replace the product with refurbished
equipment.
• From 1 year to 3 years from purchase, the product must be sent in for repair. Advance
replacements will be sent for a fee of $100.
If you have questions about this policy, please contact GE-Interlogix Kalatel Division’s RMA Department
at 800-469-1676.
0150-0193F
87
Kalatel DVMRe Triplex
0150-0193F