Gas Slide-In
Ranges
www.GEAppliances.com
Safety Instructions . . . . . . . . . . . .2–7
Owner’s Manual
Operating Instructions
Baking or Roasting . . . . . . . . . . . . . .12
Broiling, Broiling Guide . . . . . . . . .14
Clock and Timer . . . . . . . . . . . . . . .15
Control Lockout . . . . . . . . . . . . . . .11
Cookware . . . . . . . . . . . . . . . . . . . . . .9
Oven . . . . . . . . . . . . . . . . . . . . . .10–21
Sabbath Feature . . . . . . . . . . . . . . . .18
Self-Cleaning . . . . . . . . . . . . . . .20, 21
Special Features . . . . . . . . . . . . . . . .17
Surface Burners . . . . . . . . . . . . . . 8, 9
Thermostat . . . . . . . . . . . . . . . . . . . .19
Timed Baking & Roasting . . . . . . . .16
Care and Cleaning
Broiler Pan and Grid . . . . . . . . . . . 24
Burner Assembly . . . . . . . . . . . . . . . 22
Burner Grates, Vent Grille
and Vent Grille Cap . . . . . . . . . . . . 23
Control Panel . . . . . . . . . . . . . . . . . 26
Door . . . . . . . . . . . . . . . . . . . . . . . . . 25
Floor . . . . . . . . . . . . . . . . . . . . . . . . .26
Knobs . . . . . . . . . . . . . . . . . . . . . . . . 22
JGSP28
Lift-Off Oven Door . . . . . . . . . . . . .25
Light Bulbs . . . . . . . . . . . . . . . . .23, 24
Oven Vent and
Cooktop Air Inlet . . . . . . . . . . . . . . .26
Packaging Tape . . . . . . . . . . . . . . . .22
Painted Surfaces . . . . . . . . . . . . . . . .26
Racks . . . . . . . . . . . . . . . . . . . . . . . . 24
Stainless Steel Surfaces . . . . . . . . . .26
Storage Drawer . . . . . . . . . . . . . . . . 24
Vent . . . . . . . . . . . . . . . . . . . . . . . . . 26
Troubleshooting Tips . . . . . . . 27–30
Accessories . . . . . . . . . . . . . . . . . . . 33
Consumer Support
Consumer Support . . . . . Back Cover
Product Registration . . . . . . . . . 31, 32
Warranty . . . . . . . . . . . . . . . . . . . . . 34
Write the model and serial
numbers here:
Model # ______________
Serial # ______________
You can find them on a label
behind the open oven door
on the lower left corner of the
range frame.
49-80257-1 11-04 JR
WARNING!
ANTI-TIP DEVICE
■ ALL RANGES CAN TIP
■ INJURY TO PERSONS
COULD RESULT
■ INSTALL ANTI-TIP
DEVICES PACKED WITH
RANGE
■ SEE INSTALLATION
INSTRUCTIONS
Operating Instructions
Safety Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Care and Cleaning
WARNING: If the information
in this manual is not followed exactly,
a fire or explosion may result causing
property damage, personal injury
or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT
TO DO IF YOU
SMELL GAS
Troubleshooting Tips
■ Do not try to light any appliance.
■ Do not touch any electrical switch;
do not use any phone in your building.
■ Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
■ If you cannot reach your gas supplier,
call the fire department.
Consumer Support
— Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
2
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
ANTI-TIP DEVICE
To prevent accidental tipping of the range, attach it to the wall or floor by installing the Anti-Tip device
supplied.
If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip
device WB2X7909.
To check if the device is installed and engaged properly, remove the storage drawer and inspect the
rear leveling leg. Make sure it fits securely into the slot.
If you pull the range out from the wall for any reason, make sure the device is properly
engaged when you push the range back against the wall. If it is not, there is a possible risk of
the range tipping over and causing injury if you or a child stand, sit or lean on an open door.
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to
publish a list of substances known to the state to cause birth defects or other reproductive harm, and
requires businesses to warn customers of potential exposure to such substances.
The fiberglass insulation in self-clean ovens gives off a very small amount of carbon monoxide during
the cleaning cycle. Exposure can be minimized by venting with an open window or using a ventilation
fan or hood.
Troubleshooting Tips
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon
monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or
LP fuels. Properly adjusted burners, indicated by a bluish rather than a yellow flame, will minimize
incomplete combustion. Exposure to these substances can be minimized by venting with an open
window or using a ventilation fan or hood.
Care and Cleaning
Please refer to the Anti-Tip device information in this manual. Failure to take this precaution
could result in tipping of the range and injury.
Operating Instructions
All ranges can tip and injury could result.
Safety Instructions
www.GEAppliances.com
Consumer Support
3
WARNING!
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the
following:
■ Use this appliance only for its intended
■ Do not attempt to repair or replace any
purpose as described in this Owner’s
part of your range unless it is specifically
Manual.
recommended in this manual. All other
service should be referred to a qualified
■ Be sure your appliance is properly installed
technician.
and grounded by a qualified technician in
accordance with the provided installation
■ Be sure your range is correctly adjusted
instructions.
by a qualified service technician or installer
for the type of gas (natural or LP) that is
■ Before performing any service, disconnect
to be used. Your range can be converted
the range power supply at the household
for use with either type of gas. See the
distribution panel by removing the fuse or
Installation Instructions packed with
switching off the circuit breaker.
the range.
■ Have the installer show you the location of
■ Plug your range into a 120-volt grounded
the circuit breaker or fuse. Mark it for easy
outlet only. Do not remove the round
reference.
grounding prong from the plug. If in
doubt about the grounding of the home
■ Do not leave children alone—children
electrical system, it is your personal
should not be left alone or unattended in
responsibility and obligation to have
an area where an appliance is in use. They
an ungrounded outlet replaced with a
should never be allowed to sit or stand on
properly grounded, three-prong outlet in
any part of the appliance.
accordance with the National Electrical
■ Have the installer show you the location
Code. Do not use an extension cord with
of the range gas shut-off valve and how to
this appliance.
shut it off if necessary.
Care and Cleaning
Operating Instructions
Safety Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Troubleshooting Tips
■ Have your range installed and properly
grounded by a qualified installer, in
accordance with the Installation
Instructions. Any adjustment and service
should be performed only by qualified gas
range installers or service technicians.
■ Locate the range out of kitchen traffic path
and out of drafty locations to prevent poor
air circulation.
Consumer Support
■ Be sure all packaging materials are
removed from the range before operating
it to prevent fire or smoke damage should
the packaging material ignite.
■ Do not leave children alone or unattended
where a range is hot or in operation. They
could be seriously burned.
4
WARNING: These adjustments
must be made by a qualified service
technician in accordance with the
manufacturer’s instructions and all codes
and requirements of the authority having
jurisdiction. Failure to follow these
instructions could result in serious injury or
property damage. The qualified agency
performing this work assumes
responsibility for the conversion.
■ Keep the hood and grease filters clean to
maintain good venting and to avoid grease
fires.
■ Teach children not to play with the
controls or any other part of the range.
■ Always keep dish towels, dish cloths, pot
holders and other linens a safe distance
from your range.
SAFETY PRECAUTIONS
■ Do not store flammable materials in an
oven, a range storage drawer or near a
cooktop.
■ Always keep combustible wall coverings,
curtains or drapes a safe distance from
your range.
■ Do not store or use combustible materials,
gasoline or other flammable vapors and
liquids in the vicinity of this or any other
appliance.
■ Do not clean the range with flammable or
volatile cleaning fluids.
■ After prolonged use of a range, high floor
temperatures may result and many floor
coverings will not withstand this kind of
use. Never install the range over vinyl tile
or linoleum that cannot withstand such
type of use. Never install it directly over
interior kitchen carpeting.
CAUTION: Items of interest to children
should not be stored in cabinets above a range or
on the backsplash of a range—children climbing
on the range to reach items could be seriously
injured.
appliance as a space heater to heat or
warm the room. Doing so may result
in carbon monoxide poisoning and
overheating of the cooktop or oven.
■ For your safety, never use your appliance
for warming or heating the room.
■ Large scratches or impacts to glass doors
can lead to broken or shattered glass.
■ Never wear loose-fitting or hanging
garments while using the appliance.
Be careful when reaching for items stored
in cabinets over the range. Flammable
material could be ignited if brought in
contact with flame or hot oven surfaces
and may cause severe burns.
■ Flame in the oven can be smothered
completely by closing the oven door and
turning the control to off or by using a
multi-purpose dry chemical or foam-type
fire extinguisher.
■ Let the burner grates and other surfaces
cool before touching them or leaving
them where children can reach them.
■ Never block the vents (air openings) of
the range. They provide the air inlet and
outlet that are necessary for the range to
operate properly with correct combustion.
Air openings are located through the rear
and front center of the cooktop, at the top
and bottom of the oven door, and at the
bottom of the range under the storage
drawer or kick panel.
■ Do not lift the cooktop. Lifting the
cooktop can lead to damage and improper
operation of the range.
5
Consumer Support
■ Do not clean the range when the appliance
is in use.
■ Flaming grease outside a pan can be put
out by covering it with baking soda or,
if available, by using a multi-purpose dry
chemical or foam-type fire extinguisher.
Troubleshooting Tips
WARNING: NEVER use this
■ Do not use water on grease fires. Never
pick up a flaming pan. Turn the controls
off. Smother a flaming pan on a surface
burner by covering the pan completely
with a well-fitting lid, cookie sheet or flat
tray. Use a multi-purpose dry chemical or
foam-type fire extinguisher.
Care and Cleaning
■ Do not allow anyone to climb, stand or
hang on the oven door, storage drawer or
cooktop. They could damage the range
and even tip it over, causing severe
personal injury.
■ Do not let cooking grease or other
flammable materials accumulate in or
near the range.
Operating Instructions
■ Always keep wooden and plastic utensils
and canned food a safe distance from your
range.
Safety Instructions
www.GEAppliances.com
WARNING!
SURFACE BURNERS
Use proper pan size—avoid pans that are unstable or easily tipped. Select cookware having flat bottoms large
enough to cover burner grates. To avoid spillovers, make sure cookware is large enough to contain the food
properly. This will both save cleaning time and prevent hazardous accumulations of food, since heavy spattering
or spillovers left on range can ignite. Use pans with handles that can be easily grasped and remain cool.
Operating Instructions
Safety Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
■ Always use the LITE position when igniting
the top burners and make sure the burners
have ignited.
■ Never leave the surface burners unattended
at high flame settings. Boilovers cause
smoking and greasy spillovers that may
catch on fire.
■ Adjust the top burner flame size so it does
not extend beyond the edge of the cookware.
Excessive flame is hazardous.
Care and Cleaning
■ Use only dry pot holders—moist or damp pot
holders on hot surfaces may result in burns
from steam. Do not let pot holders come
near open flames when lifting cookware. Do
not use a towel or other bulky cloth in place
of a pot holder.
■ When using glass cookware, make sure it
is designed for top-of-range cooking.
Troubleshooting Tips
■ To minimize the possibility of burns, ignition
of flammable materials and spillage, turn
cookware handles toward the side or back of
the range without extending over adjacent
burners.
■ Carefully watch foods being fried at a high
flame setting.
■ Always heat fat slowly, and watch as it heats.
Consumer Support
■ Do not leave any items on the cooktop. The
hot air from the vent may ignite flammable
items and will increase pressure in closed
containers, which may cause them to burst.
■ When preparing flaming foods under the
hood, turn the fan on.
■ Do not use a wok on the cooking surface
if the wok has a round metal ring that is
placed over the burner grate to support the
wok. This ring acts as a heat trap, which may
damage the burner grate and burner head.
Also, it may cause the burner to work
improperly. This may cause a carbon
monoxide level above that allowed by current
standards, resulting in a health hazard.
■ Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over
the sides of the pan.
■ Never try to move a pan of hot fat, especially
a deep fat fryer. Wait until the fat is cool.
■ Do not leave plastic items on the cooktop—
they may melt if left too close to the vent.
■ Keep all plastics away from the surface
burners.
■ To avoid the possibility of a burn, always be
certain that the controls for all burners are
at the OFF position and all grates are cool
before attempting to remove them.
■ If range is located near a window, do not
hang long curtains that could blow over the
surface burners and create a fire hazard.
■ If a combination of oils or fats will be used
in frying, stir together before heating or
as fats melt slowly.
■ If you smell gas, turn off the gas to the range
and call a qualified service technician. Never
use an open flame to locate a leak.
■ Use a deep fat thermometer whenever
possible to prevent overheating fat beyond
the smoking point.
■ Always turn the surface burner controls off
before removing cookware.
■ Do not operate the burner without all burner
parts in place.
6
■ the pan too full of fat can cause spillovers
when food is added.
■ Use the least possible amount of fat for
effective shallow or deep-fat frying. Filling
COOK MEAT AND POULTRY THOROUGHLY…
Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry to at least an
INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against foodborne illness.
OVEN
Stand away from the range when opening the oven door. Hot air or steam which escapes can cause
burns to hands, face and/or eyes.
■ Do not heat unopened food containers.
Pressure could build up and the container
could burst, causing an injury.
■ Keep the oven vents unobstructed.
■ Keep the oven free from grease buildup.
■ When using cooking or roasting bags in the
oven, follow the manufacturer’s directions.
■ Pulling out the rack to the stop-lock is a
convenience in lifting heavy foods. It is also a
precaution against burns from touching hot
surfaces of the door or oven walls.
■ Do not use the oven to dry newspapers.
If overheated, they can catch on fire.
■ Do not use aluminum foil to line oven bottoms,
except as suggested in this manual. Improper
installation of aluminum foil may result in a
risk of electric shock or fire.
■ Make sure the broiler pan is in place correctly
to reduce the possibility of grease fires.
■ If you should have a grease fire in the broiler
pan, press the CLEAR/OFF pad and keep the
oven door closed to contain fire until it
burns out.
SELF-CLEANING OVEN
Do not use oven cleaners. No commercial oven cleaner or oven liner protective coating of any kind should be
used in or around any part of the oven. Residue from oven cleaners will damage the inside of the oven when the
self-clean cycle is used.
■ If the self-cleaning mode malfunctions, turn the
oven off and disconnect the power supply. Have
it serviced by a qualified technician.
■ Before self-cleaning the oven, remove the racks,
broiler pan, grid and other cookware.
■ Clean only parts listed in this Owner’s Manual.
■ Be sure to wipe up excess spillage before
starting the self-cleaning operation.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
7
Consumer Support
■ Do not clean the door gasket. The door gasket
is essential for a good seal. Care should be
taken not to rub, damage or move the gasket.
Troubleshooting Tips
■ Do not use the oven for a storage area. Items
stored in an oven can ignite.
WARNING:
NEVER cover
any slots, holes or passages in the oven bottom
or cover an entire rack with materials such as
aluminum foil. Doing so blocks air flow
through the oven and may cause carbon
monoxide poisoning. Aluminum foil linings
may also trap heat, causing a fire hazard.
Care and Cleaning
■ Place the oven rack in the desired position
while the oven is cool. If racks must be handled
when hot, do not let pot holder contact the
heating elements.
■ Do not leave paper products, cooking utensils
or food in the oven when not in use.
Operating Instructions
WARNING!
Safety Instructions
www.GEAppliances.com
Safety Instructions
Throughout this manual, features and appearance may vary from your model.
How to Light a Gas Surface Burner
Push the control knob in and turn it to
the LITE position.
You will hear a little clicking noise—
the sound of the electric spark igniting
the burner.
Push the control knob in and turn it
to the LITE position.
When one burner is turned to LITE, all
the burners spark. Do not attempt to
disassemble or clean around any burner
while another burner is on. An electric
shock may result, which could cause you
to knock over hot cookware.
After the flame lights, turn the knob to
adjust the flame size. If the knob stays at
LITE, it will continue to click.
Sealed Gas Burners
The smaller burner (right rear position)
will give the best simmer results for
delicate foods, such as sauces or foods
which need to cook over low heat for a
long time. It can be turned down to a very
low setting.
Care and Cleaning
Operating Instructions
Using the gas surface burners.
The largest burners are higher powered
than the others and will bring liquids to
a boil quicker.
How to Select Flame Size
For safe handling of cookware, never let the flames
extend up the sides of the cookware.
Troubleshooting Tips
Watch the flame, not the knob, as you
reduce heat. The flame size on a gas
burner should match the cookware
you are using.
Any flame larger than the bottom of the
cookware is wasted and only serves to heat
the handle.
Consumer Support
In Case of Power Failure
In case of a power failure, you can light
the gas surface burners on your range
with a match. Hold a lit match to the
burner, then push in and turn the control
knob to the LITE position. Use extreme
caution when lighting burners this way.
Surface burners in use when an electrical
power failure occurs will continue to
operate normally.
Before Lighting a Gas Burner
After Lighting a Gas Burner
■ Make sure all grates on the range are in
place before using any burner.
■ Do not operate the burner for an
extended period of time without
cookware on the grate. The finish on
the grate may chip without cookware
to absorb the heat.
■ Be sure the burners and grates are
cool before you place your hand,
a pot holder, cleaning cloths or
other materials on them.
8
Top-of-Range Cookware
Heatproof Glass Ceramic: Can be used
for either surface or oven cooking. It
conducts heat very slowly and cools very
slowly. Check cookware manufacturer’s
directions to be sure it can be used on gas
ranges.
Cast-Iron: If heated slowly, most skillets
will give satisfactory results.
Stainless Steel: This metal alone has
poor heating properties and is usually
combined with copper, aluminum
or other metals for improved heat
distribution. Combination metal skillets
usually work satisfactorily if they are used
with medium heat as the manufacturer
recommends.
Enamelware: Under some conditions,
the enamel of some cookware may
melt. Follow cookware manufacturer’s
recommendations for cooking methods.
Glass: There are two types of glass
cookware—those for oven use only
and those for top-of-range cooking
(saucepans, coffee and teapots).
Glass conducts heat very slowly.
Care and Cleaning
Stove Top Grills
Do not use stove top grills on your sealed
gas burners. If you use the stove top grill
on the sealed gas burner, it will cause
incomplete combustion and can result
in exposure to carbon monoxide levels
above allowable current standards.
This can be hazardous to your health.
Troubleshooting Tips
Wok This Way
Use a flat-bottomed wok.
Operating Instructions
Aluminum: Medium-weight cookware is
recommended because it heats quickly
and evenly. Most foods brown evenly in
an aluminum skillet. Use saucepans with
tight-fitting lids when cooking with
minimum amounts of water.
Safety Instructions
www.GEAppliances.com
We recommend that you use a 14-inch or smaller
flat-bottomed wok. They are available at your
local retail store. Make sure the wok bottom
sits flat on the grate.
Only a flat-bottomed wok should be used.
Consumer Support
Do not use a round-bottomed wok on a
support ring. Placing the ring over the
burner or grate may cause the burner
to work improperly, resulting in carbon
monoxide levels above allowable
standards. This could be dangerous
to your health.
9
Throughout this manual, features and appearance may vary from your model.
Operating Instructions
Safety Instructions
Using the oven controls.
CONTROL LOCK/UNLOCK
PRESS + AND – AND HOLD FOR 3 SECONDS
Care and Cleaning
Oven Control, Clock and Timer Features and Settings
BAKE/TEMP RECALL Pad
KITCHEN TIMER ON/OFF Pad
Touch this pad to select the bake function.
Touch this pad to select the timer feature.
Then press + and – pads to adjust time.
BAKE Light
Flashes while in edit mode—you can change
the oven temperature at this point. Glows
when the oven is in bake mode.
START/ON Pad
Must be touched to start any cooking or
cleaning function.
Display
Troubleshooting Tips
Shows the time of day, oven temperature,
whether the oven is in the bake, broil or
self-cleaning mode and the times set for
the timer or automatic oven operations.
The display will show “PrE” while
preheating. When the oven reaches
the selected temperature, the oven
control will beep and the display
will show the oven temperature.
Function Error Code
If “F– and a number or letter” flash in the display and the
oven control signals, this indicates a function error code.
Consumer Support
If the function error code appears during the self-cleaning
cycle, check the oven door latch. The latch handle may have
been moved, even if only slightly, from the latched position.
Make sure the latch is moved to the right as far as it will go.
Touch the CLEAR/OFF pad. Allow the oven to cool for
one hour. Put the oven back into operation. If the function
error code repeats, disconnect the power to the range and
call for service.
TIMER Light
Flashes while in edit mode—you can change
the set time at this point. Glows when the
timer has been activated. Flashes again when
the time has run out until the control is reset.
CLOCK Pad
To set clock, touch this pad twice and then
touch the + and – pads. The time of day will
flash in display when oven is first turned on.
DELAY START Pad
Use along with the COOKING TIME or
SELF CLEAN pads to set the oven to start
and stop automatically at a time you set.
DELAY START Time Light
Flashes while in edit mode—you can change
the delay start set time at this point. Glows
when the function has been activated.
COOKING TIME Pad
Touch this pad and then touch the + or –
pads to set the amount of time you want
your food to cook. The oven will shut off
when the cooking time has run out.
COOKING TIME Light
Flashes while in edit mode—you can change
set time at this point. Glows when function
has been activated. Flashes again when the
time has run out until the control is reset.
AUTOMATIC OVEN Light
10
This lights anytime the oven has been
programmed using the COOKING TIME or
DELAY START functions.
Oven Control, Clock and Timer Features and Settings
– Pad
CLEAR/OFF Pad
Short taps to this pad will decrease the time
or temperature by small amounts. Touch
and hold the pad to decrease the time or
temperature by larger amounts.
Touch this pad to cancel ALL oven
operations except the clock and timer.
Short taps to this pad will increase the time
or temperature by small amounts. Touch
and hold the pad to increase the time or
temperature by larger amounts.
SELF CLEAN Pad
Touch this pad to select the self-cleaning
function. See the Using the self-cleaning
oven section.
CLEAN Light
Touch this pad to select the broil function.
BROIL Light
Flashes while in edit mode—you can switch
from HI to LO BROIL at this point. Glows when
the oven is in broil mode.
Indicator Lights (on some pads)
EDIT mode lasts several seconds after the
last pad press. DELAY START ON/OFF and
COOKING TIME ON/OFF will be the only pads
lit if either of these options is selected.
(Example: DELAY START is selected with
BAKE—the DELAY START pad will remain
lit until the clock reaches the programmed
time, at which point it will turn off and the
BAKE/TEMP RECALL pad light will light up).
Control Lockout
CONTROL LOCK/UNLOCK
PRESS + AND – AND HOLD FOR 3 SECONDS
Your control will allow you to lock out the touch
pads so they cannot be activated when touched.
To lock/unlock the controls:
To unlock the control, touch the +
and – pads at the same time for 3
seconds, until the display shows
LOC OFF.
■ The adjustment will be retained in
memory after a power failure.
Power Outage
CAUTION: Do not make any attempt
to operate the electric ignition oven during an
electrical power failure.
If the oven is in use when a power failure
occurs, the oven burner shuts off and
cannot be re-lit until power is restored.
This is because the flow of gas is
automatically stopped and will not
resume when power is restored until
the glow bar has reached operating
temperature.
If your oven was set for a timed oven operation
and a power outage occurred, the clock and all
programmed functions must be reset.
To reset the clock, touch the CLOCK pad.
Enter the correct time of day by touching
the + or – pads. Touch the START/ON pad.
11
Consumer Support
The oven or broiler cannot be lit during
a power failure. Gas will not flow unless
the glow bar is hot.
If a flashing time is in the display, electric power
has been restored. Reset the clock.
Troubleshooting Tips
Touch the + and – pads at the same
time for 3 seconds, until the display
shows LOC ON.
When this feature is on and the touch
pads are touched, the control will beep
and the display will show LOC ON.
■ The control lockout mode affects all
touch pads. No touch pads will work
when this feature is activated.
Care and Cleaning
Flashes while in edit mode—you can change
the length of time for the self-clean cycle at
this point. Glows when the oven is in the selfclean cycle. After the self-clean cycle, the light
will turn off. Unlatch the door.
BROIL HI/LO Pad
Operating Instructions
+ Pad
Safety Instructions
www.GEAppliances.com
Safety Instructions
To avoid possible burns, place the racks in the desired position before you turn the oven on.
Before you begin…
The racks have stops, so that when placed
correctly on the supports, they will stop
before coming completely out, and will
not tilt.
When placing and removing cookware,
pull the rack out until it stops.
The bake burner is under the oven floor.
Do not place foods on the oven bottom
for cooking.
To remove a rack, pull it toward you,
tilt the front end up and pull it out.
The oven has 7 rack positions.
To replace, place the end of the rack
(stop-locks) on the support, tilt up the
front and push the rack in.
CAUTION:
When you are using the
rack in the lowest position (A), you will need to
use caution when pulling the rack out. We
recommend that you pull the rack out several
inches and then, using two pot holders, pull the
rack out by holding the sides of it. The rack is low
and you could be burned if you place your hand in
the middle of the rack and pull all the way out. Be
very careful not to burn your hand on the door
when using the rack in the lowest position (A).
How to Set the Oven for Baking or Roasting
Care and Cleaning
Operating Instructions
Using the oven.
Touch the BAKE pad.
Type of Food
Touch the + or – pads until the
desired temperature is displayed.
Touch the START/ON pad.
Frozen pies (on cookie sheet)
Consumer Support
Troubleshooting Tips
The oven will start automatically. The
display will show “PrE” while preheating.
When the oven reaches the selected
temperature, the oven control will beep
several times and the display will show
the oven temperature.
To change the oven temperature during BAKE
cycle, touch the BAKE pad and then the + or –
pads to get the new temperature.
Check food for doneness at
minimum time on recipe. Cook
longer if necessary.
Touch the CLEAR/OFF pad when
baking is finished and then remove
the food from the oven.
NOTE: A cooling fan will automatically turn on
and off to cool internal parts. This is normal, and
the fan may continue to run even after the oven
in turned off.
12
Angel food cake
Rack Position
C or D
A
Bundt or pound cakes
B or C
Biscuits, muffins, brownies,
cookies, cupcakes,
layer cakes, pies
C or D
Casseroles
C or D
Turkey
A
If baking four cake layers at the same
time, place two layers on rack B and two
layers on rack D. Stagger pans on the
rack so one is not directly above the
other.
Preheating and Pan Placement
Preheat the oven if the recipe calls for it.
Preheating is necessary for good results
when baking cakes, cookies, pastry and
breads.
Aluminum Foil
You can use aluminum foil to line the
broiler pan and broiler grid. However,
you must mold the foil tightly to the grid
and cut slits in it just like the grid.
Cut slits in the foil just like the grid.
Never entirely cover a rack with
aluminum foil. This will disturb the heat
circulation and result in poor baking.
A smaller sheet of foil may be used to
catch a spillover by placing it on a lower
rack several inches below the food.
Oven Moisture
As your oven heats up, the temperature
change of the air in the oven may cause
water droplets to form on the door glass.
These droplets are harmless and will
evaporate as the oven continues to
heat up.
Your oven is vented through the rear vent
located through the cooktop under the
vent grille. Do not block this vent when
cooking in the oven—it is important that
the flow of hot air from the oven and
fresh air to the oven burner be
uninterrupted. Avoid touching the vent
openings or nearby surfaces during oven or
broiler operation—they may become hot.
■ Handles of pots and pans on the cooktop may
become hot if left too close to the vent.
■ Do not leave plastic items on the cooktop—
they may melt if left too close to the vent.
■ Do not leave any items on the cooktop. The hot
air from the vent may ignite flammable items
and will increase pressure in closed containers,
which may cause them to burst.
13
Consumer Support
■ Metal items will become very hot if they are
left on the cooktop, and could cause burns.
Troubleshooting Tips
Oven Vent
Care and Cleaning
Without the slits, the foil will prevent fat
and meat juices from draining into the
broiler pan. The juices could become
hot enough to catch on fire. If you
do not cut the slits, you are essentially
frying, not broiling.
Do not use aluminum foil on the bottom of
the oven.
Operating Instructions
Do not place foods directly on the
oven floor.
To preheat, set the oven at the correct temperature.
The control will beep when the oven is preheated
and the display will show your set temperature.
The preheat time will vary depending on the
temperature setting.
Baking results will be better if baking
pans are centered in the oven as much
as possible. If baking with more than one
pan, place the pans so each has at least 1″
to 11⁄2″ of air space around it.
Safety Instructions
www.GEAppliances.com
Safety Instructions
Operating Instructions
Care and Cleaning
Troubleshooting Tips
Consumer Support
Using the oven.
How to Set the Oven for Broiling
Always use the broiler pan and
grid that came with your oven. It
is designed to minimize smoking
and spattering by trapping juices
in the shielded lower part of the
pan.
IMPORTANT: To avoid possible burns, place the
racks in the desired position before you turn the
oven on.
Place the meat or fish on the broiler
grid in the broiler pan.
Follow suggested rack positions in
the Broiling Guide.
Use LO Broil to cook foods such as poultry
or thick cuts of meat thoroughly without
over-browning them.
Touch the START/ON pad.
When broiling is finished, touch the
CLEAR/OFF pad.
Serve the food immediately, and leave the
pan outside the oven to cool during the
meal for easiest cleaning.
The oven door must be closed
during broiling.
Touch the BROIL HI/LO pad once for
HI Broil.
To change to LO Broil, touch the
BROIL HI/LO pad again.
Broiling Guide
The size, weight, thickness,
starting temperature
and your preference
of doneness will affect
broiling times. This guide
is based on meats at
refrigerator temperature.
† The U.S. Department of
Agriculture says “Rare beef is
popular, but you should know that
cooking it to only 140°F means
some food poisoning organisms
may survive.” (Source: Safe Food
Book. Your Kitchen Guide. USDA
Rev. June 1985.)
The oven has 7 rack positions.
14
Food
Ground Beef
Beef Steaks
Rare†
Medium
Well Done
Rare†
Medium
Well Done
Chicken
Quantity and/
or Thickness
/ ″ to 3/4″ thick
Rack
First Side Second Side
Position Time (min.) Time (min.) Comments
1 2
D
13
8
Space evenly.
3/4″ to 1″ thick
1 to 11/2 lbs.
F
E
E
6
8
10
4
6
8
11/2″ thick
2 to 21/2 lbs.
Steaks less than 3/4″
thick are difficult
to cook rare.
Slash fat.
E
E
D
C
15
15
20
25
10
15
20
25
C
25
15
1 whole cut up
2 to 21⁄2 lbs.,
split lengthwise
Breast
Bakery Product
Bread (toast)
English Muffin
2 to 4 slices
2 (split)
F
F
3
3-4
1
Lobster Tails
2–4
C
18–20
Do not
turn
over.
Fish Fillets
1 lb. (1/4″ to 1/2″ thick)
E
6
6
Salmon
Steaks
Fillets
2 (1″ thick)
2 (1/2″ to 3/4″ thick)
E
E
10
15
5
/ ″ thick
1″ thick
2 (1/2″ thick)
2 (1″ thick) about 1 lb.
D
D
D
D
8
8
10
15
5
8
10
5
Ham Slices
(precooked)
Pork Chops
Well Done
1 2
Brush each side with
melted butter.
Broil skin-side-down
first.
Space evenly. Place
English muffins cutside-up and brush
with butter if desired.
Cut through back of
shell. Spread open.
Brush with melted
butter before broiling
and after half of
broiling time.
Handle and turn very
carefully. Brush with
lemon butter before
and during cooking,
if desired.
Turn carefully.
Do not turn skin-sidedown.
Slash fat.
www.GEAppliances.com
Not all features are on all models.
To Set the Clock
The clock must be set to the correct time
of day for the automatic oven timing
functions to work properly. The time of
day cannot be changed during a delayed
cooking or a delayed self-cleaning cycle.
Touch the + or – pads.
Make sure the clock is set to the
correct time of day.
If the + or – pads are not touched within
one minute after you touch the CLOCK
pad, the display reverts to the original
Touch the START/ON pad until the
time of day shows in the display. This
enters the time and starts the clock.
To check the time of day when the display is
showing other information, simply touch the
CLOCK pad. The time of day shows until another
pad is touched.
To Turn Off the Clock Display
If you have several clocks in your kitchen,
you may wish to turn off the time of day
clock display on your range.
Touch the CLOCK pad twice to recall
the clock display.
To Set the Timer
The timer does not control oven operations.
The maximum setting on the timer is 9 hours
and 59 minutes.
The CLEAR/OFF pad does not affect
the timer.
Touch the + or – pads until the
amount of time you want shows in
the display. The maximum time that
can be entered in minutes is 59.
Times more than 59 minutes should
be changed to hours and minutes.
Touch the START/ON pad. The time
will start counting down, although
the display does not change until
one minute has passed.
When the timer reaches :00, the
control will beep 3 times followed by
one beep every 6 seconds until the
KITCHEN TIMER ON/OFF pad is
touched.
To Reset the Timer
If the remaining time is not in the display
(clock, delay start set time or cooking
time are in the display), recall the
remaining time by touching the KITCHEN
TIMER ON/OFF pad and then touching the
+ or – pads to enter the new time you
want.
To Cancel the Timer
Touch the KITCHEN TIMER ON/OFF
pad twice.
15
Consumer Support
If the display is still showing the time
remaining, you may change it by touching
the KITCHEN TIMER ON/OFF pad, then
touching the + or – pads until the time
you want appears in the display.
Troubleshooting Tips
Touch the KITCHEN TIMER ON/OFF
pad.
If you make a mistake, touch the KITCHEN
TIMER ON/OFF pad and begin again.
Care and Cleaning
Touch the CLOCK pad once to turn
off the time of day display. Although
you will not be able to see it, the
clock maintains the correct time
of day.
Operating Instructions
Touch the CLOCK pad twice.
setting. If this happens, touch the CLOCK
pad twice and reenter the time of day.
Safety Instructions
Using the clock and timer.
Do not lock the oven door with the latch during timed cooking. The latch is used for self-cleaning only.
NOTE: Foods that spoil easily—such as milk, eggs, fish, stuffings, poultry and pork—should not be allowed to sit for
more than 1 hour before or after cooking. Room temperature promotes the growth of harmful bacteria. Be sure that
the oven light is off because heat from the bulb will speed harmful bacteria growth.
How to Set an Immediate Start and Automatic Stop
The oven will turn on immediately and cook for a
selected length of time. At the end of the cooking
time, the oven will turn off automatically.
Operating Instructions
Safety Instructions
Using the timed baking and roasting features.
Touch the BAKE pad.
Touch the + or – pads to set the
oven temperature.
Touch the COOKING TIME pad.
NOTE: If your recipe requires preheating, you may
need to add additional time to the length of the
cooking time.
Care and Cleaning
Touch the + or – pads to set the
baking time.
Touch the START/ON pad.
The display shows either the oven
temperature that you set or the cooking
time countdown. (The display starts with
“PrE” if showing the oven temperature.)
The oven will continue to cook for the
programmed amount of time, then turn
off automatically.
Touch the CLEAR/OFF pad to clear
the display if necessary.
Remove the food from the oven. Remember, even
though the oven shuts off automatically, foods
continue cooking after controls are off.
The cooking time that you entered
will be displayed. (If you select Cooking
Time first and then adjust the Bake
Temperature, the oven temperature
will be displayed instead).
How to Set a Delayed Start and Automatic Stop
Troubleshooting Tips
The oven will turn on at the time of day you set,
cook for a specific length of time and then turn off
automatically.
Make sure the clock shows the correct
time of day.
Touch the BAKE pad.
Touch the + or – pads to set the
oven temperature.
Touch the COOKING TIME pad.
Touch the + or – pads to set the
desired length of cooking time.
Touch the DELAY START pad.
Consumer Support
Touch the + or – pads to set the time
of day you want the oven to turn on
and start cooking.
Touch the START/ON pad.
NOTE: An attention tone will sound if you are
using timed baking and do not touch the
START/ON pad.
16
NOTE: If you would like to check the times
you have set, touch the DELAY START pad
to check the delay start set time you have
set or touch the COOKING TIME pad to
check the length of cooking time you
have set.
When the oven turns on at the time of day
you have set, the display will show “PrE”
until it reaches the selected temperature,
then it will display the oven temperature.
At the end of cooking time, the oven
will turn off and the end-of-cycle tone
will sound.
Touch the CLEAR/OFF pad to clear
the display if necessary.
Remove the food from the oven. Remember, even
though the oven shuts off automatically, foods
continue cooking after controls are off.
www.GEAppliances.com
Your new touch pad control has additional features that you may choose to use. The following are the features and
how you may activate them.
The special feature modes can only be activated while the display is showing the time of day. They remain in the
control’s memory until the steps are repeated.
When the display shows your choice, touch the START/ON pad. The special features will remain in memory after
a power failure.
12 Hour Shut-Off
With this feature, should you forget and leave the
oven on, the control will automatically turn off the
oven after 12 hours during baking functions or
after 3 hours during a broil function.
If you wish to turn OFF this feature, follow
the steps below.
Touch the BAKE and BROIL HI/LO
pads at the same time for 3 seconds
until the display shows SF.
Touch the CLOCK pad. The display
will show ON (12 hour shut-off).
Touch the CLOCK pad repeatedly
until the display shows OFF (no
shut-off).
Touch the START/ON pad to activate
the no shut-off and leave the control
set in this special features mode.
Operating Instructions
NOTE: The Sabbath feature and the Thermostat Adjustment feature are also Special Features, but they are
addressed separately in the following sections.
Safety Instructions
Special features of your oven control.
Care and Cleaning
Troubleshooting Tips
Consumer Support
17
(Designed for use on the Jewish Sabbath and Holidays)
The Sabbath feature can be used for baking/roasting only. It cannot be used for broiling, self-cleaning or
Delay Start cooking.
NOTE: The oven light comes on automatically (on some models) when the door is opened and goes off when the
door is closed. The bulb may be removed. See the Oven Light Replacement section. On models with a light switch
on the control panel, the oven light may be turned on and left on.
How to Set for Regular Baking/Roasting
NOTE: To understand how the oven control works,
practice using regular baking (non-Sabbath) before
entering Sabbath mode.
Make sure the clock shows the correct time of day
and the oven is off.
Touch and hold both the BAKE and
BROIL HI/LO pads, at the same time,
until the display shows SF.
Tap the CLOCK pad until SAb appears
in the display.
Touch the START/ON pad and ⊃ will
appear in the display.
Touch the BAKE pad. No signal will
be given.
When the display shows ⊃ the
oven is set in Sabbath. When the
display shows ⊃ ⊃ the oven is
baking/roasting.
After a random delay period of
approximately 30 seconds to 1 minute,
⊃ ⊃ will appear in the display indicating
that the oven is baking/roasting. If ⊃ ⊃
doesn’t appear in the display, start again
at Step 4.
To adjust the oven temperature, touch the
BAKE pad and tap the + or – pads to increase
or decrease the temperature in 5° increments.
Touch the START/ON pad.
NOTE: The CLEAR/OFF and COOKING TIME pads
are active during the Sabbath feature.
To exit Sabbath feature see next page.
The preset starting temperature will
automatically be set to 350.° Tap the +
or – pads to increase or decrease the
temperature in 5° increments. The
temperature can be set between 170°
and 550.° No signal or temperature
will be given.
NOTE: To understand how the oven control works,
practice using regular (non-Sabbath) Immediate Start
and Automatic Stop before entering the Sabbath mode.
Make sure the clock shows the correct time of day
and the oven is off.
Touch and hold both the BAKE and
BROIL HI/LO pads, at the same time,
until the display shows SF.
Tap the CLOCK pad until SAb appears
in the display.
Touch the START/ON pad and ⊃ will
appear in the display.
Touch the COOKING TIME pad.
Consumer Support
Touch the START/ON pad.
How to Set for Timed Baking/Roasting—Immediate Start and Automatic Stop
Troubleshooting Tips
Care and Cleaning
Operating Instructions
Safety Instructions
Using the Sabbath Feature.
When the display shows ⊃ the
oven is set in Sabbath. When the
display shows ⊃ ⊃ the oven is
baking/roasting.
18
Touch the + or – pads to set the desired
length of cooking time between 1
minute and 9 hours and 59 minutes.
The cooking time that you entered will
be displayed.
Touch the START/ON pad.
Touch the BAKE pad. No signal will
be given.
The preset starting temperature will
automatically be set to 350.° Tap the +
or – pads to increase or decrease the
temperature in 5° increments. The
temperature can be set between 170°
and 550.° No signal or temperature
will be given.
Touch the START/ON pad.
After a random delay period of
approximately 30 seconds to 1 minute,
⊃ ⊃ will appear in the display indicating
that the oven is baking/roasting. If ⊃ ⊃
doesn’t appear in the display, start again
at Step 7.
To adjust the oven temperature, touch the
BAKE pad and tap the + or – pads to increase
or decrease the temperature in 5° increments.
Touch the START/ON pad.
When cooking is finished, the display will
change from ⊃ ⊃ to ⊃ indicating that the
oven has turned OFF but is still set in Sabbath.
Remove the cooked food.
How to Exit the Sabbath Feature
Touch the CLEAR/OFF pad.
Tap the CLOCK pad until ON or OFF
appears in the display. ON indicates that
the oven will automatically turn off after
12 hours. OFF indicates that the oven
will not automatically turn off. See
the Special Features section for an
explanation of the 12 Hour Shut-Off
feature.
If the oven is cooking, wait for a random
delay period of approximately 30
seconds to 1 minute, until only ⊃ is in
the display.
Touch the START/ON pad.
NOTE: If a power outage occurred while the oven was
in Sabbath, the oven will automatically turn off and stay
off even when the power returns. The oven control
must be reset.
Adjust the oven thermostat—Do it yourself!
You may find that your new oven cooks differently than the one it replaced. Use your new oven for a few
weeks to become more familiar with it. If you still think your new oven is too hot or too cold, you can adjust
the thermostat yourself.
NOTE: This adjustment will not affect the broiling or the self-cleaning temperatures. The adjustment will be
retained in memory after a power failure.
To Adjust the Thermostat
Touch the BAKE and BROIL HI/LO
pads at the same time for 2 seconds
until the display shows SF.
The oven temperature can be
adjusted up to (+) 35°F hotter or (–)
35°F cooler. Touch the + pad to
increase the temperature in 1-degree
increments.
NOTE: This adjustment will not affect the broiling
or self-cleaning temperatures. It will be retained
in memory after a power failure.
Touch the – pad to decrease the
temperature in 1-degree increments.
The type of margarine will affect baking performance!
Recipe failure can result if cakes, pies, pastries, cookies or candies are made with low-fat spreads. The lower the fat
content of a spread product, the more noticeable these differences become.
Federal standards require products labeled “margarine” to contain at least 80% fat by weight. Low-fat spreads,
on the other hand, contain less fat and more water. The high moisture content of these spreads affects the
texture and flavor of baked goods. For best results with your old favorite recipes, use margarine, butter or
stick spreads containing at least 70% vegetable oil.
19
Consumer Support
Most recipes for baking have been developed using high-fat products such as butter or margarine (80% fat). If you
decrease the fat, the recipe may not give the same results as with a higher-fat product.
Troubleshooting Tips
Touch the BAKE pad. A two-digit
number shows in the display.
When you have made the
adjustment, touch the START/ON pad
to go back to the time of day display.
Use your oven as you would
normally.
Care and Cleaning
Do not use thermometers, such as those found in grocery stores, to check the temperature setting of your oven.
These thermometers may vary 20–40 degrees.
Operating Instructions
Touch and hold both the BAKE and
BROIL HI/LO pads, at the same time,
until the display shows SF.
Safety Instructions
www.GEAppliances.com
Safety Instructions
Never force the latch handle. Forcing the handle will damage the door lock mechanism.
Before a Clean Cycle
We recommend venting your kitchen
with an open window or using a
ventilation fan or hood during the
first self-clean cycle.
Remove the racks, broiler pan, broiler
grid, all cookware and any aluminum foil
from the oven.
Wipe up heavy soil on the oven
bottom.
NOTE: Take the racks out of the oven
before you begin the self-clean cycle or
they may discolor.
Soil on the front frame of the range and
outside the gasket on the door will need
to be cleaned by hand. Clean these areas
with hot water, soap-filled steel wool pads
or cleansers such as Soft Scrub®. Rinse
well with clean water and dry.
Care and Cleaning
Operating Instructions
Using the self-cleaning oven.
Do not clean the gasket. The fiberglass
material of the oven door gasket cannot
withstand abrasion. It is essential for the
gasket to remain intact. If you notice it
becoming worn or frayed, replace it.
Wipe up any heavy spillovers on the oven
bottom.
Make sure the oven light bulb cover is in
place and the oven light is off.
IMPORTANT: The health of some birds
is extremely sensitive to the fumes given
off during the self-cleaning cycle of any
range. Move birds to another wellventilated room.
How to Set the Oven for Cleaning
Follow the directions in the Before a
Clean Cycle section.
Latch the door.
Touch the SELF CLEAN pad.
Troubleshooting Tips
Touch the + or – pads until the
desired Clean Time is displayed.
The Clean Time is normally 4 hours. You can
change the Clean Time to any time between 3
and 5 hours, depending on the amount of soil in
your oven.
Touch the START/ON pad.
Consumer Support
The self-clean cycle will automatically
begin after CLEAN is displayed and the
time countdown appears in the display.
20
While the oven is self-cleaning, you can
touch the CLOCK pad to display the time
of day. To return to the clean countdown,
touch the SELF CLEAN pad.
The oven shuts off automatically when
the clean cycle is complete, and 0:00 will
flash in the display.
Slide the latch handle to the left as
far as it will go and open the door.
It will not be possible to unlatch the oven
door until the temperature drops below
the lock temperature and the clean light
goes off.
When the clean light is off, unlatch the
door.
How to Delay the Start of Cleaning
Make sure the clock shows the correct
time of day.
Using the + or – pads, enter the
desired clean time.
When the clean light is off, unlatch the
door.
Latch the door.
The Clean Time is normally 4 hours. You can
change the Clean Time to any time between 3
and 5 hours, depending on the amount of soil in
your oven.
Touch the DELAY START pad. The
earliest delay start time you can set
will appear in the display.
Using the + or – pads, enter the
time of day you want the clean cycle
to start.
Operating Instructions
Touch the SELF CLEAN pad.
The display will show the delay start set
time. It will not be possible to unlatch the
oven door until the temperature drops
below the lock temperature and the
clean light goes off.
Safety Instructions
www.GEAppliances.com
Touch the START/ON pad.
Care and Cleaning
To Stop a Clean Cycle
Touch the CLEAR/OFF pad.
Wait until the oven has cooled below the
locking temperature to unlatch the door.
You will not be able to open the door
right away unless the oven has cooled
below the locking temperature.
You may notice some white ash in the
oven. Wipe it up with a damp cloth after
the oven cools.
■ You cannot set the oven for cooking
until the oven is cool enough for the
door to be unlatched.
If white spots remain, remove them with a soapfilled scouring pad and rinse thoroughly with
a vinegar and water mixture.
■ While the oven is self-cleaning, you
can touch the CLOCK pad to display
the time of day. To return to the
clean countdown, touch the COOKING
TIME pad.
These deposits are usually a salt
residue that cannot be removed by
the clean cycle.
■ Apply a small amount of vegetable oil
to a paper towel and wipe the edges of
the oven racks with the paper towel. Do
not spray with Pam® or other lubricant
sprays.
21
Consumer Support
If the oven is not clean after one clean
cycle, repeat the cycle.
Troubleshooting Tips
After a Clean Cycle
Safety Instructions
Care and cleaning of the range.
Be sure all controls are off and all surfaces are cool before cleaning any part of the range.
If your range is removed for cleaning, servicing or any reason, be sure the anti-tip
device is reengaged properly when the range is replaced. Failure to take this
precaution could result in tipping of the range and cause injury.
Care and Cleaning
Operating Instructions
How to Remove Packaging Tape
To assure no damage is done to the finish
of the product, the safest way to remove
the adhesive left from packaging tape and
cooktop labels on new appliances is an
application of a household liquid dishwashing
detergent, mineral oil or cooking oil.
Control Knobs
The control knobs may be removed for easier cleaning.
Before removing the knobs for cleaning,
please note that the knobs are in the OFF
position. When replacing the knobs, check
the OFF position to insure proper placement.
Wash the knobs in soap and water or a
vinegar and hot water solution but do not
soak.
The knobs can also be cleaned in a
dishwasher.
Burner Assembly
Make sure the slot in the burner
head is positioned over electrode.
CAUTION:
DO NOT
OPERATE THE BURNER WITHOUT
ALL BURNER PARTS IN PLACE.
Consumer Support
Troubleshooting Tips
Apply with a soft cloth and allow to soak.
Wipe dry and then apply an appliance polish
to thoroughly clean and protect the surface.
NOTE: The adhesive must be removed from all parts.
It cannot be removed if it is baked on.
22
The burner assemblies should be washed
regularly and, of course, after spillovers.
Turn all controls off before removing burner parts.
The burner grates, burner heads and burner
caps can be removed for easy cleaning.
The electrode of the spark igniter is exposed
beyond the surface of the burner base. When
cleaning the cooktop, be careful not to snag
the electrode of the spark igniter with your
cleaning cloth. Damage to the igniter could
occur. To avoid snagging a cloth on the spark
igniter, leave the burner heads in place when
cleaning the cooktop.
Be careful not to push in any cooktop
controls while cleaning the cooktop. A slight
electrical shock might result which could
cause you to knock over hot cookware.
Wash burner parts with an all-purpose
non-abrasive cleaner and warm water. Soak
stubborn soil. Dry them with a cloth—do not
reassemble while wet.
To reassemble the surface burners:
Place burner heads over the electrodes
on the cooktop, in the correct locations
according to their size.
Small head
and cap
Medium head
and cap
Front of range
Large head
and cap
Large head
and cap
Place the
Grate
matching
size caps
onto the
Burner cap
heads.
Make sure
that the
Burner head
heads and
caps are
placed in
the correct
locations.
After
cleaning,
first replace the vent grille and vent
grille cap. Replace the side grates so that
they fit over the tabs on the vent grille.
Make sure the grates are positioned
securely over the burners and that
they are stable and level.
Vent grille
cap
Burner Grates, Vent Grille and Vent Grille Cap
Vent grille
Porcelain enamel burner grates, vent
grille and vent grille cap should be
washed regularly and, of course, after
spillovers.
Air inlet
Although they’re durable, the grates,
vent grille and vent grille cap will
gradually lose their shine, regardless of
the best care you can give them. This is
due to their continual exposure to high
temperatures.
Rubber Grate Feet
For stability, your cooktop has rubber
feet on the burner grates. If any of these
rubber feet should become damaged or
lost, replace them immediately.
To order replacement rubber grate feet,
please call our toll-free number:
National Parts
Center . . . . . . . . . . . . . . . . . . .800.626.2002
Rubber Grate Feet . . . . . . .#WB02T10101
Do not operate a burner for an extended
period of time without cookware on the
grate. The finish on the grate may chip
without cookware to absorb the heat.
Care and Cleaning
After cleaning, first replace the vent grille
and the vent grille cap.
Socket
Receptacle
Oven Light Bulbs (on some models)
NOTE: The glass cover should be
removed only when cold. Wearing latex
gloves may offer a better grip.
CAUTION: Before replacing your
Tab
Glass cover
Receptacle
oven light bulb, disconnect the electrical
power to the oven at the main fuse or
circuit breaker panel.
Be sure to let the light cover and bulb
cool completely.
Troubleshooting Tips
Bulb
Use gloves
or cloth
For your safety, do not touch a hot bulb
with bare hands or a damp cloth.
Using gloves or a dry cloth, remove
the bulb by pulling it straight out.
To replace:
Use a new 130-volt halogen bulb,
not to exceed 50 watts.
Using gloves or a dry cloth, remove
the bulb from its packaging. Do not
touch the bulb with bare fingers.
Push the bulb straight into the
receptacle all the way.
Place the tabs of the glass cover into
the grooves of the socket. Turn the
glass cover clockwise 1/4 turn to
engage.
For improved lighting inside
the oven, clean the glass cover
frequently using a wet cloth. This
should be done when the oven is
completely cool.
Reconnect electrical power to
the oven.
23
Consumer Support
To remove:
Turn the glass cover
counterclockwise 1/4 turn until the
tabs of the glass cover clear the
grooves of the socket.
Operating Instructions
Wash them in hot, soapy water and
rinse with clean water. You may also use
abrasive cleaners and scouring pads, if
needed. Dry them with a cloth—don’t
put them back on the cooktop wet.
Replace the side grates so that they fit
over the tabs on the vent grille. Make
sure the grates are positioned securely
over the burners and that they are stable
and level.
Safety Instructions
www.GEAppliances.com
Oven Light Replacement (on some models)
CAUTION: Before replacing your oven
light bulb, disconnect the electrical power to the
range at the main fuse or circuit breaker panel.
Be sure to let the light cover and bulb
cool completely.
To remove the cover:
Twist lens counterclockwise about a
quarter turn to remove.
Do not remove any screws to remove
the cover.
Replace bulb with a 40-watt
appliance bulb or two-prong
halogen bulb as appropriate.
To replace the cover:
Line up tabs of lens in front of tabs
on housing and rotate clockwise to
engage.
Connect electrical power to the
range.
Broiler Pan and Grid
Do not clean the broiler pan or grid in a
self-cleaning oven.
Do not store a soiled broiler pan
and grid anywhere in the range.
After broiling, remove the broiler pan
from the oven. Remove the grid from the
pan. Carefully pour out the grease from
the pan into a proper container.
Wash and rinse the broiler pan and grid in hot
water with a soap-filled or plastic scouring pad.
If food has burned on, sprinkle the grid
with detergent while hot and cover with
wet paper towels or a dishcloth. Soaking
the pan will remove burned-on foods.
Both the broiler pan and grid may be cleaned with
a commercial oven cleaner.
Both the broiler pan and grid can also be
cleaned in a dishwasher.
Storage Drawer Removal
To remove the drawer:
Troubleshooting Tips
Care and Cleaning
Operating Instructions
Safety Instructions
Care and cleaning of the range.
Rail
Stop guide
To replace the drawer:
Pull the drawer out until it stops.
Place the drawer rails on the guides.
Lift the front of the drawer until the
stops clear the guides.
Push the drawer back until it stops.
Remove the drawer.
Lift the front of the drawer and
push back until the stops clear the
guides.
Lower the front of the drawer and
push back until it closes.
Oven Racks
Consumer Support
Oven rack
Clean the oven racks with an abrasive
cleanser or scouring pad. After cleaning,
rinse the racks with clean water and dry
with a clean cloth.
NOTE: The oven racks may be cleaned in the
self-cleaning oven. However, the oven racks
will darken in color, lose their luster and
become hard to slide if cleaned during the
self-cleaning cycle.
To make the oven racks slide more easily,
apply a small amount of cooking oil to a
paper towel and wipe the edges of the
oven racks with the paper towel.
24
Cleaning the Oven Door
To clean the inside of the door:
■ Because the area inside the gasket is
cleaned during the self-clean cycle, you
do not need to clean this by hand.
■ The area outside the gasket and
the door liner can be cleaned with a
soap-filled or plastic scouring pad,
hot water and detergent. Rinse well
with a vinegar and water solution.
To clean the outside of the door:
■ Use soap and water to thoroughly
clean the top, sides and front of the
oven door. Rinse well. You may also
use a glass cleaner to clean the glass
■ If any stain on the door vent trim is
persistent, use a soft abrasive cleaner
and a sponge-scrubber for best results.
■ Spillage of marinades, fruit juices,
tomato sauces and basting materials
containing acids may cause
discoloration and should be wiped
up immediately. When surface is cool,
clean and rinse.
■ Do not use oven cleaners, cleaning
powders or harsh abrasives on the
outside of the door.
Lift-Off Oven Door
Do not lift the door by the handle.
Slot
To remove the door:
Fully open the door.
Hinge lock
Pull hinge locks down to unlock.
Pull the hinge locks down toward
the door frame, to the unlocked
position. A tool, such as a small
flat-blade screwdriver, may be
required.
Close door to the door removal
position, which is halfway between
the broil stop position and fully
closed.
Removal position
Lift door up and out until the hinge
arm is clear of the slot.
Push the hinge locks up against the
front frame of the oven cavity to the
locked position.
Hinge
arm
To replace the door:
Hinge lock
Push hinge locks up to lock.
Consumer Support
Firmly grasp both sides of the door
at the top.
Troubleshooting Tips
Firmly grasp both sides of the door
at the top.
Bottom
With the
Hinge arm
edge
door at the
of slot
same angle as
the removal
position, seat the
Indentation
indentation of
the hinge arm
into the bottom
edge of the hinge slot. The notch in
the hinge arm must be fully seated
into the bottom of the slot.
Fully open the door. If the door will
not fully open, the indentation is
not seated correctly in the bottom
edge of the slot.
Care and Cleaning
The door is very heavy. Be careful when
removing and lifting the door.
Operating Instructions
The gasket is designed with a gap at the
bottom to allow for proper air circulation.
Do not rub or clean the door gasket—
it has an extremely low resistance to
abrasion.
If you notice the gasket becoming worn,
frayed or damaged in any way or if it has
become displaced on the door, you should
have it replaced.
on the outside of the door. Do not let
water drip into the vent openings.
Safety Instructions
www.GEAppliances.com
Close the oven door.
25
Safety Instructions
Operating Instructions
Care and cleaning of the range.
To order:
To order CERAMA BRYTE® Stainless
Steel Cleaning Polish and Conditioner,
please call our toll-free number:
National Parts Center. . 800.626.2002
www.GEAppliances.com
CERAMA BRYTE®
Stainless Steel Cleaning Polish
and Conditioner . . . . . . # PM10X313
Stainless Steel Surfaces (on some models)
Do not use a steel-wool pad; it will
scratch the surface.
Clean a small area
(approximately 8″ x 8″), rubbing
with the grain of the stainless steel
if applicable.
Shake bottle well.
Place a small amount of
CERAMA BRYTE® Stainless Steel
Cleaning Polish and Conditioner
on a dry cloth or dry paper towel.
Dry and buff with a clean, dry
paper towel or soft cloth.
Repeat as necessary.
Painted Surfaces
Painted surfaces include the top and
sides of the door, and the drawer front.
Clean these with soap and water or
a vinegar and water solution.
Do not use commercial oven cleaners,
cleaning powders, steel wool or harsh
abrasives on any painted surface.
Oven Vent and Cooktop Air Inlet
Care and Cleaning
Oven vent
The oven is vented through an opening
in the cooktop under the grille. The
cooktop takes in air through the air inlet
located through the cooktop.
Never cover these openings with
aluminum foil or any other material.
This would prevent the vents from
working properly.
Cooktop air inlet
Troubleshooting Tips
Control Panel
If desired, the touch pads may be turned off
before cleaning.
Remove heavier soil with warm soapy
water. Do not use abrasives of any kind.
See the Control Lockout section.
Turn on the touch pads after cleaning.
Clean up splatters with a damp cloth.
Oven floor
Removable Oven Floor
To remove the oven floor for easier
cleaning:
Remove the oven door using the
instructions in the Lift-Off Oven Door
section.
Consumer Support
Grasp oven floor at the rear finger
slots on each side, lift it up, push it
back and pull it out.
26
Clean the oven floor with warm
soapy water.
IMPORTANT: Always replace the
removable floor before the next use.
www.GEAppliances.com
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Possible Causes
What To Do
Burners have yellow or
yellow-tipped flames
The combustion quality of
burner flames needs to be
determined visually.
• Use the illustrations below to determine if your burner
flames are normal. If burner flames look like A, call for
service. Normal burner flames should look like B or C,
depending on the type of gas you use. With LP gas, some
yellow tipping on outer cones is normal.
A–Yellow flames
Call for service
B–Yellow tips
on outer cones
Normal for LP gas
C–Soft blue flames
Normal for natural
gas
Knob isn’t pushed down.
• To turn from the OFF position, push the knob in and
then turn.
Burners do
not light
Plug on range is not
completely inserted in the
electrical outlet.
• Make sure electrical plug is plugged into a live, properly
grounded outlet.
Gas supply not connected
or turned on.
• See the Installation Instructions that came with your
range.
A fuse in your home may be
blown or the circuit breaker
tripped.
• Replace the fuse or reset the circuit breaker.
Burner parts not replaced
correctly.
• See the Care and cleaning of the range section.
• If LOC ON appears in the display, the oven control is
locked. Turn this feature off to use the oven. See the
Control Lockout section.
Control knob is still
in the LITE position.
• Turn the knob out of the LITE position to the desired
setting.
Burner flames very
large or yellow
Improper air to gas ratio.
Oven light does
not work
Light bulb is loose or defective. • Tighten or replace the bulb.
Oven will not work
Plug on range is not completely • Make sure electrical plug is plugged into a live, properly
inserted in the electrical outlet.
grounded outlet.
• Turn the burner off and relight. If ticking is still
present, call for service.
Switch operating
light is broken.
A fuse in your home may be
blown or the circuit
breaker tripped.
• If range is connected to LP gas, check all steps
in the Installation Instructions that came with
your range.
• Call for service.
• Replace the fuse or reset the circuit breaker.
Oven controls improperly set. • See the Using the oven section.
Door left in the locked position. • If necessary, allow the oven to cool; then unlock
the door.
27
Consumer Support
Ticking sound of spark
igniter persists after
burner lights
Troubleshooting Tips
Control Lockout feature
is activated
Care and Cleaning
Control knobs
will not turn
Operating Instructions
Problem
Safety Instructions
Before you call for service…
Safety Instructions
Troubleshooting Tips
Problem
Possible Causes
What To Do
Food does not bake
or roast properly
Oven controls improperly set.
• See the Using the oven section.
Rack position is incorrect
or the rack is not level.
• See the Using the oven section.
Incorrect cookware or
cookware of improper
size being used.
• See the Using the oven section.
Oven thermostat needs
adjustment.
• See the Adjust the oven thermostat – Do it yourself!
section.
Oven controls improperly set.
• Make sure you touch the BROIL HI/LO pad.
Improper rack position
being used.
• See the Broiling Guide.
Cookware not suited
for broiling.
• Use the broiling pan and grid that came with your range.
Aluminum foil used on the
the broiling pan and grid has
not been fitted properly and
slit as recommended.
• See the Using the oven section.
In some areas the power
(voltage) may be low.
• Preheat the broil element for 10 minutes.
• Broil for the longest period of time recommended in
the Broiling Guide.
Oven temperature
too hot or too cold
Oven thermostat
needs adjustment.
• See the Adjust the oven thermostat – Do it yourself!
section.
Oven door is crooked
The door is out of position.
• Because the oven door is removable, it sometimes
gets out of position during installation. Remove and
replace the oven door. See the Lift-Off Oven Door
section.
Storage drawer
is crooked
Rear drawer support is
on top of the guide rail.
• Reposition the drawer. See the Storage Drawer
Removal instructions in the Care and cleaning of your
range section.
Storage drawer
won’t close
Rear drawer support is
on top of the guide rail.
• Reposition the drawer. See the Storage Drawer
Removal instructions in the Care and cleaning of
your range section.
Food does not
broil properly
Consumer Support
Troubleshooting Tips
Care and Cleaning
Operating Instructions
Before you call for service…
28
Problem
Possible Causes
Clock and timer do
not work
Plug on range is not completely • Make sure electrical plug is plugged into a live, properly
inserted in the electrical outlet.
grounded outlet.
• Replace the fuse or reset the circuit breaker.
Oven controls improperly set. • See the Using the clock and timer section.
Oven will not self-clean
• See the Using the self-cleaning oven section.
Oven door is not in the
locked position.
• Make sure you move the door latch handle all the way
to the right.
“Crackling” or
“popping” sound
This is the sound of the
metal heating and cooling
during both the cooking and
cleaning functions.
• This is normal.
Excessive smoking
during a clean cycle
Excessive soil.
• Touch the CLEAR/OFF pad. Open the windows to
rid the room of smoke. Wait until the light on the
SELF CLEAN pad goes off. Wipe up the excess soil
and reset the clean cycle.
Oven door will not
open after a clean cycle
Oven too hot.
• Allow the oven to cool below locking temperature.
Oven not clean after a
clean cycle
Oven controls not properly set. • See the Using the self-cleaning oven section.
“F—and a number
or letter” flash
in the display
You have a function error code. • Touch the CLEAR/OFF pad. Put the oven back into
operation.
Oven was heavily soiled.
• Clean up heavy spillovers before starting the clean
cycle. Heavily soiled ovens may need to self-clean
again or for a longer period of time.
29
Consumer Support
• Disconnect all power to the range for at least 30
seconds and then reconnect power. If the function
error code repeats, call for service.
• If a function error code appears during the selfcleaning cycle, check the oven door latch. The latch
may have been moved, if only slightly, from the
locked position. Make sure the latch is moved to
the right as far as it will go. Touch the CLEAR/OFF pad.
Allow the oven to cool for one hour. Put the oven
back into operation.
Troubleshooting Tips
If the function code repeats.
Care and Cleaning
Oven controls improperly set.
Operating Instructions
A fuse in your home
may be blown or the
circuit breaker tripped.
What To Do
Safety Instructions
www.GEAppliances.com
Safety Instructions
Operating Instructions
Care and Cleaning
Troubleshooting Tips
Problem
Possible Causes
What To Do
Display flashes “bAd”
then “linE” with a
loud tone
The installed connection
from the house to the unit
is miswired.
• Contact installer or electrician to correct miswire.
Control signals after
entering cooking time
or delay start
You forgot to enter a
bake temperature or
cleaning time.
• Touch the BAKE pad and desired temperature or
the SELF CLEAN pad and desired clean time.
Display goes blank
A fuse in your home may
be blown or the circuit
breaker tripped.
• Replace the fuse or reset the circuit breaker.
The clock is in
black-out mode.
• See the Using the clock and timer section.
Display flashes
Power failure.
• Reset the clock.
Unable to get the
display to show “SF”
Oven control pads were
not touched properly.
• The BROIL HI/LO and BAKE pads must be touched at
the same time and held for 3 seconds.
Power outage,
clock flashes
Power outage or surge.
• Reset the clock. If the oven was in use, you must reset
it by touching the CLEAR/OFF pad, setting the clock
and resetting any cooking function.
“Burning” or “oily”
odor emitting from
the vent
This is normal in a new oven
and will disappear in time.
• To speed the process, set a self-clean cycle for a
minimum of 3 hours. See the Using the self-cleaning
oven section.
Strong odor
An odor from the insulation • This is temporary.
around the inside of the oven
is normal for the first few
times the oven is used.
Fan noise
A cooling fan may
automatically turn
on and off.
Consumer Support
Troubleshooting Tips
Before you call for service…
30
• This is normal. The cooling fan will turn off and on
to cool internal parts. It may run after the oven is
turned OFF.
GE Service Protection Plus™
GE, a name recognized worldwide for quality and dependability, offers you
Service Protection Plus ™—comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
• Backed by GE
• All brands covered
• Unlimited service calls
• All parts and labor costs included
• No out-of-pocket expenses
• No hidden deductibles
• One 800 number to call
We’ll Cover Any Appliance.
Anywhere. Anytime.*
You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224
for more information.
*All brands covered, up to 20 years old, in the continental U.S.
✁
Cut here
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
31
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
1 2 3
Complete and mail
your Consumer
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the unlikely event of a
safety modification.
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800.GE.CARES
(800.432.2737).
Model Number
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
Serial Number
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
online at www.GEAppliances.com.
✁
Cut here
Consumer Product Ownership Registration
Model Number
ant
ort l
p
Im Mai ay!
d
To
Mr. ■
Ms. ■
Mrs. ■
Serial Number
Miss ■
First
Name
Last
Name
Street
Address
Apt. #
E-mail Address*
Zip
Code
State
City
Date Placed
In Use
Day
Month
Year
Phone
Number
_
_
* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important
communications from GE Appliances (GEA).
GE Appliances
GE Consumer & Industrial
Louisville, Kentucky
www.GEAppliances.com
32
■ Check here if you do not want to receive communications from GEA’s carefully selected partners.
FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR
WARRANTY RIGHTS.
For more information about GEA’s privacy and data usage policy, go to www.GEAppliances.com and
click on “Privacy Policy” or call 800.626.2224.
Safety Instructions
Accessories.
Looking For Something More?
You can find these accessories and many more at www.GEAppliances.com or call
800.626.2002 (during normal business hours). Have your model number ready.
Surface Burner Heads & Caps
Care and Cleaning
Broiler Pan
Oven Racks
Operating Instructions
Grates
Cleaner and polish
or
Troubleshooting Tips
Light Bulbs
Knobs
Tired of discolored racks? Wishing you had extra-heavy-duty oven racks?
NOW AVAILABLE for your range:
GE’s innovative, self-cleanable porcelain-coated oven racks!
Consumer Support
• Heavy Duty
• Durable
• Able to be cleaned in a self-cleaning oven
Visit www.GEAppliances.com for more information.
33
Safety Instructions
Operating Instructions
All warranty service provided by our Factory Service Centers,
or an authorized Customer Care® technician. To schedule service,
on-line, 24 hours a day, visit us at www.GEAppliances.com, or call
800.GE.CARES (800.432.2737).
Staple your receipt here.
Proof of the original
purchase date is needed to
obtain service under the
warranty.
For The Period Of:
GE Will Replace:
One Year
From the date of the
original purchase
Any part of the range which fails due to a defect in materials or workmanship. During this
full one-year warranty, GE will also provide, free of charge, all labor and in-home service to
replace the defective part.
What GE Will Not Cover:
■ Service trips to your home to teach you how to use
the product.
■ Damage to the product caused by accident, fire, floods
or acts of God.
■ Improper installation, delivery or maintenance.
■ Incidental or consequential damage caused by possible
defects with this appliance.
■ Failure of the product if it is abused, misused,
or used for other than the intended purpose or
used commercially.
■ Damage caused after delivery.
■ Replacement of house fuses or resetting of circuit
breakers.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what
your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Troubleshooting Tips
Care and Cleaning
GE Gas Range Warranty.
Consumer Support
Warrantor: General Electric Company. Louisville, KY 40225
34
Safety Instructions
Notes.
Operating Instructions
Care and Cleaning
Troubleshooting Tips
Consumer Support
35
Consumer Support.
GE Appliances Website
www.GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service
www.GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio
www.GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties
www.GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
www.GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
www.GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
www.GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Printed in the United States