GE Medium Square Specification Sheet

g
INDOOR LIGHTING
GE
Lighting Solutions
GUIDE FORM SPECIFICATIONS
GE Evolve™ LED Series Garage Parking Deck Luminaire
GENERAL STATEMENT
The GE Evolve™ LED Series Parking Deck Luminaire is a system
that provides an high efficiency, advanced LED optical system
providing high uniformity and excellent vertical light distribution with reduced glare and effective security light levels.
Optical Systems Requirements
The Luminaire shall have:
1. Structured LED array’s for optimized vertical light photometric distribution
2. An Evolve™ Light Engine system with directional reflectors designed to optimize application efficiency and minimize glare
3. An IP 65 rated optical enclosure
4. An Injection Molded Acrylic Lens
5. LED Printed Circuit Board Assemblies utilizing a Metal Core
Printed Circuit Board
Photometric Requirements
The Luminaire shall have:
1. A nominal Correlated Color Temperature (CCT) of 6000 ºK
2. A typical Color Rendering Index (CRI) ≥ 70.
3. An option for “uplight” to increase light above the fixture.
4. A minimum initial Luminaire Efficacy ≥ 65 Im/W
6. Photometric configurations:
Photometric Type Designator Watts Narrow
125
Wide
125
Wide
95
Wide
80
Wide with Uplight
125
Wide with Uplight
95
Wide with Uplight
80
Initial Lumen
Output
8115
8115
6485
5250
8115
6485
5250
Electrical Systems Requirements
The Luminaire shall have:
1. Off-state power draw of 0 watts (excluding remote control
devices)
2. A minimum power factor of .90.
3. A nominal LED forward current ≤ 350 mA.
4. Transient voltage and surge suppression capability that
meet or exceeds the requirements of ANSI/IEEE C.62.41-1991
Location category B2 (4kV/2kA) for 8/20us Combination
Wave transients. The transient test condition shall consist of
5 strikes per mode, polarity, and phase condition (120 transients total) per the test protocol of IEC 61000-4-5 Ed 2 with
Class B performance results.
5. An operating temperature range of -40º C to 40º C.
6. UL Class 2 power supply units (i.e. drivers) operating in DC
constant current mode supplying DC forward current for LED
operation (no pulsed operation allowed)
7. Compliance with FCC 47 CFR Part 15/18 Class B.
8. A Class A sound rating.
Data subject to change without notice
Warranty Requirements
1. A limited system warranty must be provided for the replacement or repair of the luminaire due to any electrical failure
(including light source and or power supplies/drivers) for five
(5) years.
Mechanical Requirements
The Luminaire shall have:
1. maximum dimensions of 19.0 inches of length, 19.0 inches
of width, and 7.8 inches of height (without mounting options)
2. Weight ≤ 26 pounds.
3. normal operation in temperatures from -40º C to 40º C.
4. A housing construction:
a.of die cast aluminum
b.finished with corrosion resistant polyester powder paint, minimum 2.0 mil thickness, gray or white in color.
c. with internally mounted driver(s)
d.corrosion resistant fasteners
e. incorporating heat sink fins that are integrally cast with
the housing to maximize heat transfer and minimize
thermal impacts of environmental conditions such as
debris-clogged fins.
5. a vibration rating of 2G per ANSI C136.31-2001
LED Module/Array Requirements
1. LED module(s)/array(s) shall deliver at least 85% of initial
lumens, when installed for a minimum of 50,000 hours.
Measurement/Performance/Safety Standards
1. IESNA LM-79-08- Approved method for the electrical and
photometric measurements of solid-state lighting products.
2. IESNA LM-80-08 (Recommended) Approved method for measuring lumen maintenance of LED lighting sources.
3. Luminaire listed as UL 1598 approved
Guide Form Specifications – 2011