MOUNTING ARM
COVER
MOUNTING
SCREWS
CUSTOMER
LEADS
BALLAST HOUSING INSTALLATION
WIRING
BOX
Swing unit shut. Tighten ballast cover screw securely.
TETHER
Figure 5
IF MULTIWATT:
Multiwatt ballasts are available in various combinations of wattage. See wiring instructions on wiring
tag inside the luminaire.
BALLAST HOUSING
LAMP
INSTALLATION
CAUTION
Straight Stanchion Cover (See Figure 6)
Attach mounting arm onto conduit. Hang ballast housing
on cover by hinge. Proceed to Wiring.
CUSTOMER
LEADS
MOUNTING ARM
CUSTOMER LEADS
COVER
BALLAST
HOUSING
BALLAST HOUSING
Use only lamps specified on nameplate. Observe
lamp manufacturer’s recommendations and restrictions on lamp operation, particularly ballast type,
burning position, etc.
Lamp Tightness – Medium Base Lamp: The lamp should be
tightened to a light firmness sufficient to depress the center
contact.
OPTICALS
Figure 6
Figure 7
Angle Stanchion Cover (See Figure 7)
Attach mounting arm onto conduit. Hang ballast housing
on cover by hinge. Proceed to Wiring.
B.WIRING:
Cut incoming supply conductors to six (6)
inches inside cover. Route conductors through lead
clip provided and make electrical connections,
including ground as shown on wiring label (See
Figure 8).
SET SCREW
CAUTION: GLOBE IS TEMPERED GLASS. DO NOT
SCRATCH OR CHIP.
Attach globe by threading firmly into bottom of ballast
housing.
Prismatic Refractor Assembly
Type V, R or L
LEAD CLIPS
Make all electrical connections in accordance with
the National Electrical Code and any applicable local
code requirements.
Verify that supply voltage is correct by comparing it
to nameplate.
When changing voltage on reconnectable units,
move only the lead with the insulated connector.
IF SINGLE VOLTAGE:
All single voltage ballasts are pre-wired such that
user need only connect the supply conductors.
IF MULTIVOLT: (120/208/240/277 volts)
Connect the ballast lead with the insulated terminal
to the desired voltage terminal as indicated on the
ballast terminal nameplate.
GE Consumer & Industrial
Lighting Systems
Mini•Gard Luminaire
East Flat Rock, NC 28726
READ THOROUGHLY BEFORE INSTALLING
WARNING
Risk of electric shock
• Turn power off before servicing
– see instructions
THE OPERATING TEMPERATURE “T-CODE” LISTED
FOR THIS LUMINAIRE IS BASED ON THE FOLLOWING
BULB SIZES. USE OF OTHER THAN THESE MAY
RESULT IN A HIGHER OPERATING TEMPERATURE
AND COULD RESULT IN A HAZARDOUS CONDITION.
LAMP TYPE
WATTAGE BULB SIZE
HIGH PRESSURE SODIUM 70,100,150 ED 23 1/2
HIGH PRESSURE SODIUM 250, 400
ED 18
METAL HALIDE/MERCURY 175, 250
ED 28
METAL HALIDE/MERCURY 400
ED 37
Flexible Cover (See Figures 2 and 3)
Loosen four(4) bolts holding mounting hub to cover.
Position adapter plate correctly to balance luminaire. Use
widest bolt spacing possible to secure plate to cover. Hang
ballast housing on cover by hinge. Proceed to Wiring.
.875
ADJUSTMENT
MOUNTING HUB
AVERTISSEMENT: COUPER L’ALIMENTATION
AVANT L’INSTALLTION OU L’ENTRETIEN.
COVER
CUSTOMER
LEADS
GENERAL
Bolt pattern
for lower
wattages
A complete luminaire consists of a ballast housing,
optical assembly, and a cover/mounting.
Thread adapter firmly into ballast housing. To orient
asymmetrical glass, loosen clamping screws, turn glass and
retighten screws. To relamp, unscrew complete optical from
ballast housing.
ACCESSORIES
Figure 8
INSTRUCTIONS
Risk of burn
• Allow lamp/fixture to cool before
handling
WIRING BOX DOOR
COVER
g
GEH-5754A
External Reflector
Insert mounting screws. Orient reflector to proper position
and slip over mounting screws. Turn reflector and tighten
screws securely.
MOUNTING
MAINTENANCE AND CLEANING
It will occasionally be necessary to clean optical assembly
in order to maintain light levels. Frequency of cleaning will
depend on dirt levels in user’s facility and minimum acceptable light levels . Reflector should be cleaned with any
suitable, non-abrasive solution of water and soap or detergent. Residual cleaning agent should be removed with clean
water rinsing. Glassware may be cleaned with any conventional glass cleaner. If unit gets soiled on the inside, it should
be cleaned and any damaged gasket or filter replaced.
GE Consumer & Industrial
Lighting Systems
3010 Spartanburg Highway
East Flat Rock, NC 28726
(828) 693-2000
www.gelightingsystems.com
35-201578-T8 (1/00 GELS)
INSTALLATION
CAUTION
Unit will fall if not installed properly
• Follow installation instructions
Globe Guard
Insert protective guard into ballast housing and turn until
retained by detent.
GROUND
SCREW
CAUTION: When installing luminaire in
hazardous locations check operating temperature
limits prior to installation to insure it conforms to
the environmental temperature restrictions and
NEC classifications.
Pendant Cover (See Figure 1)
Thread cover onto conduit. Orient cover and seal around
conduit using approved NEC procedures. Tighten set screw
at mounting hub. Hang ballast housing on cover by hinge.
Proceed to Wiring.
CUSTOMER LEADS
COVER
Bolt pattern
for higher
wattages
BALLAST HOUSING
Figure 2
Figure 3
Ceiling Cover (See Figure 4)
Using the slotted tabs, mount cover to ceiling. Hang
ballast housing on cover by hinge. Proceed to Wiring.
COVER
CUSTOMER
LEADS
BALLAST HOUSING
Figure 4
Figure 1
BALLAST HOUSING
®Registered Trademark of General Electric Company
Wallmount Cover (See Figure 5)
Mount wiring box provided and pull leads. Tether is
supplied to hold arm assembly while connecting supply
leads. Attach arm assembly to wiring box. Do not damage
gasket attached to arm assembly. Mounting screws should
be tightened in alternate sequence. Hang ballast housing
on cover by hinge. Proceed to Wiring.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in
connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser's purposes, the matter should be referred to General Electric Company.
MOUNTING ARM
COVER
MOUNTING
SCREWS
CUSTOMER
LEADS
BALLAST HOUSING INSTALLATION
WIRING
BOX
Swing unit shut. Tighten ballast cover screw securely.
TETHER
Figure 5
IF MULTIWATT:
Multiwatt ballasts are available in various combinations of wattage. See wiring instructions on wiring
tag inside the luminaire.
BALLAST HOUSING
LAMP
INSTALLATION
CAUTION
Straight Stanchion Cover (See Figure 6)
Attach mounting arm onto conduit. Hang ballast housing
on cover by hinge. Proceed to Wiring.
CUSTOMER
LEADS
MOUNTING ARM
CUSTOMER LEADS
COVER
BALLAST
HOUSING
BALLAST HOUSING
Use only lamps specified on nameplate. Observe
lamp manufacturer’s recommendations and restrictions on lamp operation, particularly ballast type,
burning position, etc.
Lamp Tightness – Medium Base Lamp: The lamp should be
tightened to a light firmness sufficient to depress the center
contact.
OPTICALS
Figure 6
Figure 7
Angle Stanchion Cover (See Figure 7)
Attach mounting arm onto conduit. Hang ballast housing
on cover by hinge. Proceed to Wiring.
B.WIRING:
Cut incoming supply conductors to six (6)
inches inside cover. Route conductors through lead
clip provided and make electrical connections,
including ground as shown on wiring label (See
Figure 8).
SET SCREW
CAUTION: GLOBE IS TEMPERED GLASS. DO NOT
SCRATCH OR CHIP.
Attach globe by threading firmly into bottom of ballast
housing.
Prismatic Refractor Assembly
Type V, R or L
LEAD CLIPS
Make all electrical connections in accordance with
the National Electrical Code and any applicable local
code requirements.
Verify that supply voltage is correct by comparing it
to nameplate.
When changing voltage on reconnectable units,
move only the lead with the insulated connector.
IF SINGLE VOLTAGE:
All single voltage ballasts are pre-wired such that
user need only connect the supply conductors.
IF MULTIVOLT: (120/208/240/277 volts)
Connect the ballast lead with the insulated terminal
to the desired voltage terminal as indicated on the
ballast terminal nameplate.
GE Consumer & Industrial
Lighting Systems
Mini•Gard Luminaire
East Flat Rock, NC 28726
READ THOROUGHLY BEFORE INSTALLING
WARNING
Risk of electric shock
• Turn power off before servicing
– see instructions
THE OPERATING TEMPERATURE “T-CODE” LISTED
FOR THIS LUMINAIRE IS BASED ON THE FOLLOWING
BULB SIZES. USE OF OTHER THAN THESE MAY
RESULT IN A HIGHER OPERATING TEMPERATURE
AND COULD RESULT IN A HAZARDOUS CONDITION.
LAMP TYPE
WATTAGE BULB SIZE
HIGH PRESSURE SODIUM 70,100,150 ED 23 1/2
HIGH PRESSURE SODIUM 250, 400
ED 18
METAL HALIDE/MERCURY 175, 250
ED 28
METAL HALIDE/MERCURY 400
ED 37
Flexible Cover (See Figures 2 and 3)
Loosen four(4) bolts holding mounting hub to cover.
Position adapter plate correctly to balance luminaire. Use
widest bolt spacing possible to secure plate to cover. Hang
ballast housing on cover by hinge. Proceed to Wiring.
.875
ADJUSTMENT
MOUNTING HUB
AVERTISSEMENT: COUPER L’ALIMENTATION
AVANT L’INSTALLTION OU L’ENTRETIEN.
COVER
CUSTOMER
LEADS
GENERAL
Bolt pattern
for lower
wattages
A complete luminaire consists of a ballast housing,
optical assembly, and a cover/mounting.
Thread adapter firmly into ballast housing. To orient
asymmetrical glass, loosen clamping screws, turn glass and
retighten screws. To relamp, unscrew complete optical from
ballast housing.
ACCESSORIES
Figure 8
INSTRUCTIONS
Risk of burn
• Allow lamp/fixture to cool before
handling
WIRING BOX DOOR
COVER
g
GEH-5754A
External Reflector
Insert mounting screws. Orient reflector to proper position
and slip over mounting screws. Turn reflector and tighten
screws securely.
MOUNTING
MAINTENANCE AND CLEANING
It will occasionally be necessary to clean optical assembly
in order to maintain light levels. Frequency of cleaning will
depend on dirt levels in user’s facility and minimum acceptable light levels . Reflector should be cleaned with any
suitable, non-abrasive solution of water and soap or detergent. Residual cleaning agent should be removed with clean
water rinsing. Glassware may be cleaned with any conventional glass cleaner. If unit gets soiled on the inside, it should
be cleaned and any damaged gasket or filter replaced.
GE Consumer & Industrial
Lighting Systems
3010 Spartanburg Highway
East Flat Rock, NC 28726
(828) 693-2000
www.gelightingsystems.com
35-201578-T8 (1/00 GELS)
INSTALLATION
CAUTION
Unit will fall if not installed properly
• Follow installation instructions
Globe Guard
Insert protective guard into ballast housing and turn until
retained by detent.
GROUND
SCREW
CAUTION: When installing luminaire in
hazardous locations check operating temperature
limits prior to installation to insure it conforms to
the environmental temperature restrictions and
NEC classifications.
Pendant Cover (See Figure 1)
Thread cover onto conduit. Orient cover and seal around
conduit using approved NEC procedures. Tighten set screw
at mounting hub. Hang ballast housing on cover by hinge.
Proceed to Wiring.
CUSTOMER LEADS
COVER
Bolt pattern
for higher
wattages
BALLAST HOUSING
Figure 2
Figure 3
Ceiling Cover (See Figure 4)
Using the slotted tabs, mount cover to ceiling. Hang
ballast housing on cover by hinge. Proceed to Wiring.
COVER
CUSTOMER
LEADS
BALLAST HOUSING
Figure 4
Figure 1
BALLAST HOUSING
®Registered Trademark of General Electric Company
Wallmount Cover (See Figure 5)
Mount wiring box provided and pull leads. Tether is
supplied to hold arm assembly while connecting supply
leads. Attach arm assembly to wiring box. Do not damage
gasket attached to arm assembly. Mounting screws should
be tightened in alternate sequence. Hang ballast housing
on cover by hinge. Proceed to Wiring.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in
connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser's purposes, the matter should be referred to General Electric Company.