Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
36” Chimney Vent Hood
ZV800
Safety Information
BEFORE YOU BEGIN
WARNING: TO REDUCE THE RISK OF FIRE,
Read these instructions completely and carefully.
•
ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off at
the service panel and lock service panel to prevent
power from being switched on accidentally. If the
service panel cannot be locked, fasten a tag or
prominent warning label to the panel.
IMPORTANT — Save these instructions for
local inspector’s use.
•
IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer — Be sure to leave these
instructions with the Consumer.
• Note to Consumer — Keep these instructions
with your Owner’s Manual for future reference.
• Skill Level — Installation of this appliance requires
basic mechanical and electrical skills.
• Completion Time — 1 to 3 Hours.
• Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered
under the warranty.
For Monogram local service in your area, 1.800.444.1845.
For Monogram service in Canada 1.888.880.3030
For Monogram Parts and Accessories, call 1.800.626.2002.
ADVERTISSEMENT :
POUR RÉDUIRE LE RISQUE D’INCENDIE, DE CHOC
ÉLECTRIQUE OU DE BLESSURES, IL FAUT OBSERVER LES
REGLES SUIVANTES:
A. Utiliser cet appareil uniquement de la maniére prévue
par le fabricant. En cas de question, consulter le
fabricant.
B. Avant toute intervention ou nettoyage, couper
l’alimentation électrique au disjoncteur et verrouiller
le panneau du disjoncteur pour éviter la mise sous
tension accidentelle. S’il n’est pas possible de
verrouiller le panneau du disconcteur, attacher un
placard ou une étiquette trés visible au panneau.
• For general ventilating use only. Do not use to exhaust
hazardous or explosive materials or vapors.
• Structural framing, installation work and electrical
wiring must be done by qualified person(s).
In accordance with all applicable codes and
standards including fire-rated construction.
• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
• Local codes vary. Installation electrical connections and
grounding must comply with applicable codes. In the
absence of local codes, the vent should be installed in
accordance with National Electrical Code ANSI/NFPA
70-1990 or latest edition.
CAUTION:
Due to the weight and size of these vent hoods and to
reduce the risk of personal injury or damage to the product,
TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
PRUDENCE :
À cause du poids et de la taille de ces hottes et pour
reduire le risque de blessures et de dommages, IL FAUT
DEUX PERSONNES POUR FAIRE L’INSTALLATION
CORRECTEMENT.
WARNING:
To reduce the risk of fire or electrical shock, do not
use this range hood with any external solid-state speed
control device. Any such alteration from original factory
wiring could result in damage to the unit and/or create an
electrical safety hazard.
ADVERTISSEMENT :
Pour réduire le risque d’incendie ou de choc électrique,
il ne faut pas utiliser cette hotte avec un régulateur de
vitesse électronique externe. Toute modification de ce
type du branchement d’usine peute endommager
l’appareil ou créer un risque de choc électrique.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCTWORK.
CAUTION:
To reduce risk of fire and to
properly exhaust air, be sure to duct air outside – do not
vent exhaust air into spaces within walls or ceilings or into
attics, crawl spaces, or garages.
PRUDENCE : Il faut prendre soin d’installer
un conduit vers l’extérieur pour réduire le risque d’incendie
et pouvoir évacuer l’air correctement. Il ne faut pas évacuer
l’air correctement. Il ne faut pas évacuer l’air dans l’espace
entre les parois d’un mur, un plafond ou un grenier,
un espace sanitaire ou un garage.
2
Design Information
CONTENTS
Wall-Mounted Installation – Recirculating
Ductwork, Wiring Locations................................................................14
Step 1, Install Framing for Hood Support ..........................................14
Step 2, Install Mounting Bracket ........................................................15
Step 3, Prepare the Hood ....................................................................15
Step 4, Mount the Hood ......................................................................16
Step 5, Size and Cut Duct Piece ........................................................16
Step 6, Connect Electrical....................................................................17
Step 7, Install Duct Covers ..................................................................17
Step 8, Install Filters..............................................................................18
Step 9, Finalize Installation ..................................................................18
Under-Cabinet Installation
Cabinet Requirements ..........................................................................19
Ductwork, Wiring ..................................................................................19
Step 1, Install Framing for Hood Support ..........................................20
Step 2, Prepare the Hood ....................................................................20
Step 3, Cut the Opening........................................................................21
Step 4, Install Side “L” Brackets ........................................................21
Step 5, Remove Side Screw ................................................................21
Step 6, Mount the Hood ......................................................................22
Step 7, Complete Installation and Connect Ductwork ....................22
Step 8, Connect Electrical....................................................................23
Step 9, Install Rear Mounting Screws ..............................................23
Step 10, Install Filters............................................................................23
Design Information
Product Dimensions and Clearances ..................................................3
Installation Options ................................................................................3
Advance Planning, Ductwork, Framing ..............................................4
Power Supply ..........................................................................................4
Duct Fittings..............................................................................................5
Installation Preparation
Tools and Materials Required ..............................................................6
Remove the Packaging ..........................................................................6
Wall Mount Installations ........................................................................7
Installation Below a Wall Cabinet ........................................................7
Check Installation Hardware ................................................................8
Ductwork, Wiring Locations..................................................................9
Wall-Mounted Installation – Vented to the Outside
Step 1, Install Framing for Hood Support ............................................9
Step 2, Install Mounting Bracket ........................................................10
Step 3, Install Duct Bracket ................................................................10
Step 4, Prepare the Hood ....................................................................11
Step 5, Mount the Hood ......................................................................11
Step 6, Connect Ductwork ..................................................................12
Step 7, Connect Electrical....................................................................12
Step 8, Install Duct Covers ..................................................................13
Step 9, Install Filters..............................................................................13
Step 10, Finalize Installation ................................................................13
PRODUCT DIMENSION AND
CLEARANCE
INSTALLATION OPTIONS
NOTE: The vent hood
canopy extends
forward 5-7/8”.
24” Min.
30” Max.
* Height toto
*Height
Ceiling
Ceiling
WALL-MOUNTED INSTALLATIONS
This hood may be installed onto a wall and vented to the
outdoors, or it can be installed for recirculating operation.
All necessary parts for a recirculating operation are shipped
with the hood. No kits required.
1-1/2”
1-1/2"
12-15/16”
at Sides,
12"
at Sides,
13-11/16” at Center
12-7/8" at
Center
35-7/8”
35-7/8"
* The Supplied
Supplied Duct Duct
Cover Fits
8 ft. to 10Fits
ft.
*The
Cover
Heights
8 ft. to 10Ceiling
ft. Ceiling
Heights
*24” Min.
The vent hood must be installed 24” min., and 30” max. above
the cooking surface. The telescopic duct cover conceals the
ductwork running from the top of the hood to the ceiling.
The duct cover is sized to reach 8 ft. to 10 ft. ceiling heights.
The hood installation height, from the cooking surface to the
bottom of the hood, depends upon ceiling height.
*Depending on Cabinet Height
UNDER-CABINET INSTALLATIONS
The hood may be installed beneath a cabinet. The cabinet must
measure at least 20” from the bottom frame to the inside top.
See page 19.
• Both vented and recirculating operation can be accomplished
in an under-cabinet installation. (Custom cabinet modification
is required for recirculating operation.)
3
Installation Preparation
ADVANCE PLANNING
• Use metal ductwork only. These hoods must use
6” round duct. It can transition to 3-1/4” x 12”,
reducing the maximum equivalent duct length to
75 feet.
• Install a wall cap with damper or roof cap at the
exterior opening. Order the wall or roof cap and any
transition needed in advance.
• Determine the exact location of the vent hood.
• Plan the route for venting exhaust to the outdoors.
• Use the shortest and straightest duct route possible.
For satisfactory performance, duct run should not
exceed 100 ft. equivalent length for any duct
configurations.
• Refer to “Duct Fittings” chart to compute the
maximum permissible length for duct runs to the
outdoors.
Wall Framing for Adequate Support
• This vent hood is heavy. Adequate structural support
must be provided in all types of installations. The
hood must be secured to vertical studs in the wall,
or to a horizontal support. For wall mounting
installations, see pages 9 and 14. For under-cabinet
installations, see page 20.
• The vent hood and wall cabinet, if used, should be on
site before final framing and wall finishing. This will
also help to accurately locate the duct work and
electrical service.
CAUTION:
To reduce risk of fire and to
properly exhaust air, be sure to duct air outside –
do not vent exhaust air into spaces within walls or
ceilings or into attics, crawl spaces, or garages.
PRUDENCE :
Il faut prendre soin
d’installer un conduit vers l’extérieur pour réduire le
risque d’incendie et pouvoir évacuer l’air correctement.
Il ne faut pas évacuer l’air correctement. Il ne faut pas
évacuer l’air dans l’espace entre les parois d’un mur,
un plafond ou un grenier, un espace sanitaire ou un
garage.
POWER SUPPLY
• Route house wiring through conduit as close to the
installation location as possible, in the ceiling or
back wall.
• Use a conduit connector to secure the conduit to
the junction box.
• Connect the wiring to the house wiring in accordance
with local codes.
IMPORTANT – (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
ADVERTISSEMENT :
POUR DES RAISONS DE SÉCURITÉ, CET APPAREIL
DOIT ÊTRE CORRECTEMENT MIS À LA TERRE.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with
this appliance. Follow National electrical codes or
prevailing local codes and ordinances.
Grounding instructions
The grounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
WARNING:
The improper connection of
the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
appliance is properly grounded.
Electrical supply
These vent hoods must be supplied with 120V, 60Hz, and
connected to an individual, properly grounded branch
circuit, and protected by a 15 or 20 amp circuit breaker
or time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
ADVERTISSEMENT :
Le mauvais branchement du fil de mise à la terre peut
causer un choc électrique. En cas de doute, consulter
un électricien qualifié ou un technicien pour déterminer
si l’appareil est à la terre.
4
Installation Preparation
DUCT FITTINGS
Use this chart to compute maximum
permissable lengths for duct runs
to outdoors.
NOTE: Do not exceed maximum
permissable equivalent lengths!
Maximum duct length:
100 foot for 6” round duct
75 foot for 3-1/4” x 12” duct
Flexible ducting:
If flexible metal ducting is used,
all the equivalent feet values in
the table should be doubled.
The flexible metal duct should be
straight and smooth and extended
as much as possible.
Duct Piece
Dimensions
Round,
straight
Equivalent
Length*
1 ft.
(per foot
length)
3-1/4” x 12”
3-1/4” x 24”
straight
1 ft.
(per foot
length)
6” Round
90° elbow
15 ft.
6” Round
45° elbow
8 ft.
3-1⁄4” x 12”
90° elbow
11 ft.
3-1/4” x 12” or
45° elbow
6 ft.
3-1/4” x 12”
90° flat elbow
24 ft.
6” round to
3-1/4” x 12”
or 3-1/4” x 24” transition
1 ft.
3-1/4” x 12” to 6”
round transition
8 ft.
6” round
to 3-1/4” x 12” or
transition 90° elbow
16 ft.
3-1/4” x 12” to 6” round
round transition 90° elbow
17 ft.
6” round
wall cap
with damper
30 ft.
3-1/4” x 12” wall cap
with damper
30 ft.
6” Round
roof cap
26 ft.
6” Round
roof vent
26 ft.
Quantity
Used
DO NOT use flexible plastic ducting.
NOTE: Any home ventilation system,
such as a ventilation hood, may
interrupt the proper flow of
combustion air and exhaust
required by fireplaces, gas
furnaces, gas water heaters and
other naturally vented systems. To
minimize the chance of interruption
of such naturally vented systems,
follow the heating equipment
manufacturer’s guidelines and
safety standards such as those
published by NFPA and ASHRAE.
This Hood Must Use a
6” Round Duct.
It Can Transition To
3-1/4” x 12” Duct
*Actual length of straight duct plus duct
fitting equivalent. Equivalent length of duct
pieces are based on actual tests conducted
by GE Evaluation Engineering and reflect
requirements for good venting performance
with any ventilation hood.
5
Total Duct Run
Total
Equivalent
Length
Installation Preparation
TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
… Tape measure
… Knife
Spirit level
… Spirit level
Measuring Tape
… Wire cutter/stripper
… Wire nuts
… Electric drill with 1/8" and 3/8" bits
… Phillips and flat blade screwdrivers
… Hammer
Pliers
Electric drill
… Pliers
with 1/8” and
… Safety glasses
3/8” Bits
… Duct tape
… Tape to mount template
… Gloves to protect against sharp edges
… 120V 60Hz. 15 or 20 Amp, 2 wire with
Duct Tape
ground Properly grounded branch circuit
Safety glasses
… Strain relief for junction cover
… 6" round metal duct, length to suit
installation
… Saw or jig saw
Phillips
Strain relief for
Flat blade
… Conduit for house wiring
head
junction cover
screwdriver
and conduit connector
screwdriver
Gloves
Knife
Wire
cutter/stripper
Hammer
Saw or jig saw
Wire nuts
Masking tape
Conduit
REMOVE THE PACKAGING
2-piece duct
cover
• Lift the hood out of the box.
• Remove and properly discard the plastic wrapping.
• Remove junction box cover.
• Remove the duct cover, parts box and other
packaging.
6
Installation Preparation
WALL MOUNT INSTALLATIONS
Wall Mount ZV800 Installation Heights
These hoods may be installed onto a wall or below a
wall cabinet.
• Telescopic duct covers are provided to conceal the
ductwork, running to the ceiling.
• This hood can be installed for recirculating operation.
No kits required.
24” Min.
30” Max.
36” Min.
The vent hood must be installed 24” min. and 30” max.
above the cooking surface. The hood installation
height, from the cooking surface to the bottom
of the hood, depends upon ceiling height.
INSTALLATION BELOW A CABINET
Actual
Celing
Height
*Possible VENTED
Installation Height
*Possible
RECIRCULATING
Installation Height
7’11”
24” to 27”
24” to 25”
8’ 0”
24” to 28”
24” to 26”
8’ 1”
24” to 30”
24” to 27”
8’ 2”
24” to 30”
24” to 28”
8’ 3”
24” to 30”
24” to 29”
8’ 4”
24” to 30”
24” to 30”
8’ 5”
24” to 30”
24” to 30”
8’ 6”
24” to 30”
24” to 30”
8’ 7”
24” to 30”
24” to 30”
8’ 8”
24” to 30”
24” to 30”
8’ 9”
24” to 30”
24” to 30”
8’ 10”
24” to 30”
24” to 30”
8’ 11”
24” to 30”
24” to 30”
9’ 0”
24” to 30”
24” to 30”
9’ 1”
24” to 30”
24” to 30”
9’ 2”
24” to 30”
24” to 30”
9’ 3”
24” to 30”
24” to 30”
9’ 4”
24” to 30”
24” to 30”
9’ 5”
24” to 30”
24” to 30”
9’ 6”
24” to 30”
24” to 30”
9’ 7”
25” to 30”
24” to 30”
9’ 8”
26” to 30”
24” to 30”
9’ 9”
27” to 30”
24” to 30”
9’ 10”
28” to 30”
24” to 30”
9’ 11”
29” to 30”
25” to 30”
10’
30”
26” to 30”
*Based on 36” countertop height.
INSTALLATION BELOW
A WALL CABINET
*20” Min.
Order a cabinet that is at least 20” high from the
bottom frame to the inside top. The cabinet must be
at least 12” deep.
• The hood installation height is determined by the
ceiling height.
• The hood installation height must be 24” Min. above
the cooking surface.
24” Min.
*The cabinet must measure at least 20” from the bottom
frame to the inside top. The hood housing will occupy the
interior cabinet space.
7
Installation Preparation
CHECK INSTALLATION HARDWARE
Locate the hardware accessory box packed with the hood and check contents.
4 wood
screws
4 wall
fasteners
Duct bracket
Air deflector for
recirculating
installations only
12"
Discharge damper
Mounting bracket
1 charcoal filter for
recirculating installations
29-7/8"
27-3/4"
3 Phillips head
screws to secure
electrical box to
top of motor
compartment
11-1/2"
2 stainless steel filters
2-piece decorative duct
cover (dimension shown
for reference only)
THIS EDGE
AGAINST
REAR WALL
10-13/16"
B
R
A
C
K
E
T
M
O
U
N
T
I
N
G
CL
CUT OUT THIS PORTION
THIS EDGE
AGAINST
REAR WALL
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
5-1/16"
9-5/8"
B
R
A
C
K
E
T
13-3/4"
CL
12-3/4"
REAR WALL TEMPLATE
11-3/4"
TOP CABINET TEMPLATE
49-80270
07-04 JR
Align template with centerline
and tape to bottom of the cabinet.
Cabinet installation template
8
04302127
“L” Brackets with hardware
package for cabinet-mounted
installations.
Contains 10 Phillips head screws
to secure the brackets to the
cabinet (8 required, 2 extra)
M
O
U
N
T
I
N
G
04302128
4 Phillips head decorative
screws to secure duct cover
to ceiling bracket
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
8-1/8"
2-1/16"
49-80271
07-04 JR
Wall mount template
ALIGN BOTTOM EDGE WITH
PENCIL LINE INDICATING
BOTTOM OF THE HOOD.
Installation Instructions
WALL-MOUNTED INSTALLATION—VENTED TO THE OUTSIDE
1 INSTALL FRAMING FOR HOOD
SUPPORT
DUCTWORK, WIRING LOCATIONS
Determine the exact location of the vent hood.
• Locate the template packed with the literature.
– Measure 36” from the floor to the top of the cooking
surface. Add hood installation height determined on
page 7. Mark that location.
– Use a level to draw a straight pencil line on the wall.
3-3/4” centerline to wall
IMPORTANT — Framing must be capable of
supporting 100 lbs.
min.Opening
opening for
8"6”Min.
for ductwork
Ductwork
FOR CEILING VENT DUCTING
Ceiling
ViewFrom
from rear
View
Rear
cleats
Cleats
6-1/2” dia. hole
Centerline 3-3/4”
min. above top
mounting bracket
holes
FOR WALL VENT DUCT
Drill 1/8"
Pilot Holes
1” x 6”
1"
6" min.
Min.
mounting
Mounting
support
Support
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
5-1/16"
9-5/8"
13-3/4"
CL
12-3/4"
REAR WALL TEMPLATE
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
8-1/8"
2-1/16"
49-80271
ALIGN BOTTOM EDGE WITH
PENCIL LINE INDICATING
BOTTOM OF THE HOOD.
Centerline of
Centerline
of
Installation
installation
Space
space
JR 07-04
– Tape the template in position along the penciled
line. CHECK TO BE SURE THE TEMPLATE IS LEVEL.
Ceiling ducting:
If ductwork will vent straight up to the ceiling:
• Use a level to draw a line straight up, from the centerline
on the template to the ceiling.
• Measure 3-3/4” from the back wall to the centerline of
a 6-1/2” hole on the ceiling.
NOTE: If drywall is not present, add drywall thickness to
the 3-3/4” dimension.
If drywall is present, mark the screw hole locations for
the top mounting brackets. Remove the template.
• Cut away enough drywall to expose 2 vertical studs at
the bracket location indicated on the template.
• Install a horizontal support at least 1” x 6” between
two wall studs at the top bracket installation location.
The horizontal support must be flush with the room
side of the studs. Use cleats behind both sides of the
support to secure to wall studs.
• Reinstall drywall.
Wall Ducting:
If ductwork will vent to the rear:
• Use a level to draw a line straight up from the centerline
on the template.
• Measure at least 3-3/4” above the top mounting bracket
holes shown on the template to the centerline of a
6-1/2” dia. duct hole. (Hole may be elongated for
duct elbow.)
HOUSE WIRING LOCATION:
• The junction box is located on the top right side of the
hood.
• Wiring should enter the back wall 20” to 26” above the
bottom of the hood, and within 4” of the right side of the
centerline. Wiring should enter at least 4” above the
bracket on the right side.
9
Installation Instructions
WALL-MOUNTED INSTALLATION—VENTED TO THE OUTSIDE
2 INSTALL MOUNTING BRACKET
3 INSTALL DUCT BRACKET
This vent hood must be secured to the horizontal
support or wall studs.
• With the template taped in place, use a punch to
mark all mounting screw locations.
• Drill 1/8” pilot holes at the 6 punched locations.
• Remove the template.
• The 2 holes in the support bracket holes must enter
studs or the horizontal support.
The duct bracket must be intalled against the ceiling.
This bracket will hold the duct cover in place at the top.
Secure the bracket to the ceiling and wall:
• Align the marked centerline on the bracket with the
centerline on the wall.
• Mark the 2 screw hole locations in the ceiling.
• Drill 1/8” plot holes in the marked locations.
• If pilot holes do not enter studs, enlarge the holes
to 3/8” and install wall fastener anchors.
• Drive screws, by hand, into the fasteners to allow
anchors to expand. Remove the screws.
• Secure the bracket to the ceiling and wall with
wood screws and/or fasteners.
• Use wood screws to secure the mounting bracket
to the wall. The screws must engage wall studs or
the installed horizontal mounting support.
• Check to be sure that the bracket is level. There is
no way to level the hood after hanging it from this
bracket.
C
L
10
Installation Instructions
WALL-MOUNTED INSTALLATION—VENTED TO THE OUTSIDE
4 PREPARE THE HOOD
5 MOUNT THE HOOD
• Remove the hood from the box. Remove packaging
and tape.
Electrical
panel
Install a wood screw
on each side of the
mounting frame
Remove 2 side
cover screws
Mounting
bracket
• Lift the hood onto the mounting bracket.
• Check to be sure it is level.
• Install wood screws through the hood and into the
wall on each side of the mounting bracket.
• Remove one screw on each side of the cover on the
electrical panel. Lift off the cover and set aside with
screws.
Junction box
Inside screw
Secure
electrical panel
with 3 screws
Install bottom
mounting
screws
• Extend the canopy forward for better access to the
rear mounting screw holes.
• Install 2 wood screws or fasteners through the
bottom of the hood into the wall.
• Stand the electrical panel upright.
• Align the screw holes in the bottom of the panel with
the holes on the base of the hood at the front side.
• Install 3 screws provided.
Install
• Snap the damper into the
damper
exhaust outlet on the top
of the hood.
11
Installation Instructions
WALL-MOUNTED INSTALLATION—VENTED TO THE OUTSIDE
6 CONNECT DUCTWORK
Air flow
• Install ductwork, making connections in direction of
airflow as illustrated.
• Push duct over the exhaust outlet and damper.
• Secure joints in ductwork with sheetmetal screws.
• Wrap all duct joints with duct tape for an airtight seal.
• Use duct tape to seal the flange connections.
Duct tape
over seam
and screw
CAUTION:
Do not use sheet metal
screws at the hood flange connection. Doing so
will prevent proper damper operations. Seal
connection with tape only.
Screw
PRUDENCE :
Il ne faut pas utiliser de vis autoraurdeuses à la
connexion du collet de la hotte. Ceci empêcherait
le bon fonctionnement du registre. N’utiliser que du
ruban adhésif pour assurer l’étanchéité du raccord.
7 CONNECT ELECTRICAL
Verify that power is turned off at the source.
• Remove junction box cover and knockout.
• Use a conduit connector to secure the conduit to
the junction box.
• Connect white leads to branch circuit white lead.
• Connect black leads to branch circuit black lead.
• Connect green/yellow leads to branch circuit green
lead or bare ground lead.
• Secure all connections with wire nuts on each
electrical connector.
• Push wires into junction box and replace cover.
Be sure wires are not pinched.
• Secure electrical panel cover with original screws.
WARNING:
If house wiring is not 2-wire
with a ground wire, a ground must be provided by the
installer. When house wiring is aluminum, be sure to
use U.L. approved anti-oxidant compound and
aluminum-to-copper connectors.
ADVERTISSEMENT :
Si la maison n’est pas câblee avec deux fils et un fil
de terre, l’installateur doit installer un fil de terre. Quand
les fils sont en aluminium, il faut prendre soin d’utiliser
des connecteurs aluminium à cuivre avec une pâte
antioxydante approuvée par U.L.
12
Installation Instructions
WALL-MOUNTED INSTALLATION—VENTED TO THE OUTSIDE
8 INSTALL DUCT COVERS
• Place the decorative duct
covers on top of the hood.
NOTE: The inside (upper)
duct piece has holes on one
end. The holes are intended
for use when the hood is
installed for recirculating
purposes. Slide the vented
end into the outer piece,
the vent holes should not
be visible in this installation.
9 INSTALL FILTERS
• Remove protective film on the filters.
Mounting
screws
Filter Locks
The inside duct piece must slip into the folded ends of
the outer section.
Install 2 screws,
duct cover and
into ceiling
bracket
NOTE: The charcoal filter is not required for this installation.
• Tip the filter into the slots at the rear of the opening.
Lift the filter lock and pull forward until the filter
rests in the slots.
• Install both metal grease filters.
• To remove the filters, press inwards on the handle
and pull the filter downwards.
Install
2 bottom
duct cover
screws
10 FINALIZE INSTALLATION
• Remove all packaging materials.
• Refer to the Owner’s Manual for operating
instructions.
• Extend the inner duct upwards to the ceiling bracket.
• Secure duct cover to ceiling bracket with 2 screws.
• Secure the lower duct cover to the hood by
installing 2 screws from the bottom of the hood
into the duct cover.
13
Installation Instructions
WALL-MOUNTED INSTALLATION—RECIRCULATING
1 INSTALL FRAMING FOR HOOD
SUPPORT
DUCTWORK, WIRING LOCATIONS
• Determine the exact location of the vent hood.
• Locate the template packed with the literature.
• Measure 36” from the floor to the top of the cooking
surface. Add hood installation height determined on
page 7. Mark that location.
IMPORTANT: Framing must be capable of
supporting 100 lbs.
ViewFrom
from rear
View
Rear
cleats
Cleats
Ceiling
1” x 6”
1"
6" min.
Min.
mounting
Mounting
support
Support
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Centerline
of
Centerline of
Installation
installation
Space
space
5-1/16"
9-5/8"
13-3/4"
CL
12-3/4"
REAR WALL TEMPLATE
Drill 1/8"
Pilot Holes
2-1/16"
49-80271
If drywall is present, mark the screw hole locations for
the top mounting brackets. Remove the template.
• Cut away enough drywall to expose 2 vertical studs at
the bracket location indicated on the template.
• Install a horizontal support at least 1” x 6” between
two wall studs at the top bracket installation location.
The horizontal support must be flush with the room
side of the studs. Use cleats behind both sides of the
support to secure to wall studs.
• Reinstall drywall.
Drill 1/8"
Pilot Holes
8-1/8"
ALIGN BOTTOM EDGE WITH
PENCIL LINE INDICATING
BOTTOM OF THE HOOD.
JR 07-04
• Tape the template in position along the penciled line.
CHECK TO BE SURE THE TEMPLATE IS LEVEL.
• Use a level to draw a line straight up, from the centerline
on the template to the ceiling.
HOUSE WIRING LOCATION:
• The junction box is located on the top right side of the
hood.
• Wiring should enter the back wall 20” to 26” above the
bottom of the hood, and within 4” of the right side of the
centerline.
14
Installation Instructions
WALL-MOUNTED INSTALLATION—RECIRCULATING
2 INSTALL MOUNTING BRACKET
3 PREPARE THE HOOD
This vent hood must be secured to the horizontal
support or wall studs.
• With the template taped in place, use a punch to
mark all mounting screw locations.
• Drill 1/8” pilot holes at the 6 punched locations.
• Remove the template.
• The 2 holes in the support bracket holes must enter
studs or the horizontal support.
• Remove the hood from the box. Remove packaging
and tape.
Electrical
panel
Remove 2 side
cover screws
• Remove one screw on each side of the cover on the
electrical panel. Lift off the cover and set aside with
screws.
• Use wood screws to secure the mounting bracket to
the wall. The screws must engage wall studs or the
installed horizontal mounting support.
• Check to be sure that the bracket is level.
There is no way to level the hood after hanging
it from this bracket.
Junction box
Inside screw
Secure
electrical panel
with 3 screws
• Stand the electrical panel upright.
• Align the screw holes in the bottom of the panel with
the holes on the base of the hood at the front side.
• Install 3 screws provided.
• Snap the damper into the
Install
exhaust outlet on the top of
damper
the hood.
15
Installation Instructions
WALL-MOUNTED INSTALLATION—RECIRCULATING
4 MOUNT THE HOOD
Install a wood screw
on each side of the
mounting frame
5 SIZE AND CUT DUCT PIECE
(cont.)
Mounting
bracket
• Cut the duct piece to size and
slip onto the bottom of the duct
connector.
• Use duct tape to seal and secure
the duct piece to the connector.
• Lift the hood onto the mounting bracket.
• Check to be sure it is level.
• Install wood screws through the hood and into the
wall on each side of the mounting bracket.
• Place the assembly over
the hood outlet.
• Hold the assembly against
the ceiling. The penciled
centerline should show
through the slot in the
deflector. Mark the screw
holes on the sides of the
assembly.
• Remove the assembly and
drill 1/8” pilot holes into
the wall studs.
• Enlarge holes that did not enter studs to 3/8” and
tap plastic or metal anchors into the holes, flush
with the wall.
• Mount the assembly onto the hood outlet, push up
against the ceiling and install the screws provided.
Install bottom
mounting
screws
• Extend the canopy forward for better access to the
rear mounting screw holes.
• Install 2 wood screws or fasteners through the
bottom of the hood into the wall.
CAUTION:
Do not use sheet metal screws
at the hood flange connection. Doing so will prevent
proper damper operations. Seal connection with
tape only.
5 SIZE AND CUT DUCT PIECE
• Hold upper air deflector with
duct connector against the
ceiling.
• Measure from the bottom of
the air deflector to the top of
the hood as shown. Reduce
that dimension by 1” to
facilitate installation.
The duct will cover
and overlap the
Measure
deflector and the
length
hood outlets.
ATTENTION :
N’utilisez pas de
vis autotaraudeuses pour connecter le rabat de
la hotte. En utilisant des vis, vous empêchez le
bon fonctionnement du volet de fermeture. Scellez
la connection uniquement avec du ruban adhésif.
Duct length
16
Installation Instructions
WALL-MOUNTED INSTALLATION—RECIRCULATING
6 CONNECT ELECTRICAL
Verify that power is turned off at the source.
• Remove junction box cover and knockout.
• Use a conduit connector to secure the conduit to
the junction box.
• Connect white leads to branch circuit white lead.
• Connect black leads to branch circuit black lead.
• Connect green/yellow leads to branch circuit green
lead or bare ground lead.
• Secure all connections with wire nuts on each
electrical connector.
• Push wires into junction box and replace cover.
Be sure wires are not pinched.
• Secure electrical panel cover with original screws.
WARNING:
If house wiring is not 2-wire
with a ground wire, a ground must be provided by
the installer. When house wiring is aluminum, be sure
to use U.L. approved anti-oxidant compound and
aluminum-to-copper connectors.
ADVERTISSEMENT
Si la maison n’est pas câblee avec deux fils et un fil
de terre, l’installateur doit installer un fil de terre. Quand
les fils sont en aluminium, il faut prendre soin d’utiliser
des connecteurs aluminium à cuivre avec une pâte
antioxydante approuvée par U.L.
7 INSTALL DUCT COVERS
• Place the decorative duct
covers on top of the hood.
NOTE: The inside piece has
holes on one end intended for
use when the hood is installed
for recirculating purposes.
Be sure the vented end is at
the top, the vent holes will
be visible in this installation.
Install 2 screws,
duct cover and
into ceiling
bracket
Mounting
screw holes
Vent holes
The inside duct piece must slip
into the folded ends on the outer
section.
Install
2 bottom
duct cover
screws
• Extend the inner duct piece upwards to the ceiling
mounted air deflector.
• Secure the duct cover to the air deflector, driving one
screw on each side.
• Locate the screw holes on the bottom outside edge
of the hood.
• Secure the lower duct cover to the hood by installing
2 screws from the bottom of the hood into the duct
cover.
17
Installation Instructions
WALL-MOUNTED INSTALLATION—RECIRCULATING
8 INSTALL FILTERS
9 FINALIZE INSTALLATION
• Remove all packaging materials.
• Refer to the Owner’s Manual for operating
instructions.
Charcoal filter
• Remove protective film on the filters.
• Install the black charcoal filter into the center
opening.
Metal grease filters
• Tip filters into the slots at the rear of the opening.
Lift the filter lock and pull forward until the filter
rests in the slots.
Filter Locks
• Install both metal grease filters.
• To remove the filters, press inwards on the handle
and pull the filter downwards.
18
Installation Instructions
UNDER-CABINET INSTALLATION
CABINET REQUIREMENTS
DUCTWORK, WIRING
This hood may be installed beneath a wall-mounted
cabinet.
• If the cabinet has been installed, it must be removed
so that wall framing supports can be added.
• Determine the exact location of the vent hood.
• Locate the Rear Wall Template packed with the
literature.
• Measure 36” from the floor to the top of the cooking
surface. Add the pre-determined hood installation
height. Mark that location.
• Use a level to draw a straight pencil line on the wall.
20” Min.
3-3/4” centerline
to wall
24” Min.
The cabinet must be at least 20” high between the
bottom frame and the inside top. If the cabinet is not
20” from bottom to inside top, a custom cabinet or
modifications to a different size cabinet and/or soffit
may be required to accommodate the hood housing.
• The cabinet must be 36” wide and at least 12” deep.
• The cabinet must be firmly secured to wall studs or
the added framing support and capable of supporting
100 pounds.
Ceiling
Top frame mounting
screw locations
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
5-1/16"
9-5/8"
19-1/2"
19-1/2”
13-3/4"
CL
12-3/4"
REAR WALL TEMPLATE
10-3/4”
11"
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
8-1/8"
2-1/16"
49-80271
ALIGN BOTTOM EDGE WITH
PENCIL LINE INDICATING
BOTTOM OF THE HOOD.
JR 07-04
• Tape the template in position along the penciled line.
Check to be sure the template is level.
• Use the level to draw a line straight up, from the
centerline on the template to the ceiling.
• Measure 3-3/4” from the back wall to the centerline of
a 6-1/2” hole on the ceiling.
NOTE: If drywall is not present, add drywall thickness to
the 3-3/4” dimension.
11-3/4"
11-3/4”
HOUSE WIRING LOCATION:
• The junction box is located on the top right side of the
hood.
• Wiring should enter the back wall 20” to 26” above the
bottom of the hood, and within 4” of the right side of the
centerline. Wiring should enter at least 4” above the
right side of the frame.
19
Installation Instructions
UNDER-CABINET INSTALLATION
1 INSTALL FRAMING FOR HOOD
SUPPORT
2 PREPARE THE HOOD
• Remove the hood from the box. Remove packaging
and tape.
IMPORTANT: Framing must be capable of
supporting 100 lbs.
Electrical
panel
Remove 2 side
cover screws
ViewFrom
from rear
View
Rear
cleats
Cleats
• Remove one screw on each side of the cover on
the electrical panel. Lift off the cover and set aside
with screws.
1” x 6”
1"
6" min.
Min.
mounting
Mounting
support
Support
Junction box
Inside screw
Secure
electrical panel
with 3 screws
Centerline of
Centerline
of
Installation
installation
Space
space
• Stand the electrical panel upright.
• Align the screw holes in the bottom of the panel with
the holes on the base of the hood at the front side.
• Install 3 screws provided.
• Snap the damper into the
Install
exhaust outlet on the top of
damper
the hood.
If drywall is present, mark the screw hole locations for
the top mounting brackets. Remove the template.
• Cut away enough drywall to expose 2 vertical studs at
the bracket location indicated on the template.
• Install a horizontal support at least 1” x 6” between
two wall studs at the top bracket installation location.
The horizontal support must be flush with the room
side of the studs. Use cleats behind both sides of the
support to secure to wall studs.
• Reinstall drywall.
20
Installation Instructions
UNDER-CABINET INSTALLATION
3 CUT THE OPENING
4 INSTALL SIDE “L” BRACKETS
If the cabinet has been installed, remove it from the wall.
• Use the Top Cabinet Template to locate and cut a hole
in the bottom of the cabinet.
• If necessary, place the template on top of the cabinet
to accurately cut a matching hole.
• Install the cabinet onto the wall.
The cabinet must be firmly secured to the wall and be
capable of supporting 100 lbs.
Install 2 screws in
each bracket
• Install the “L” brackets onto each side of the cutout.
The wide flat portion should be on top of the opening.
Install 2 screws into the top of each bracket.
INSTALL WOOD BLOCKS IF NECESSARY
• Install filler blocks whenever the cabinet frame hangs
below the cabinet bottom.
• Install filler blocks whenever the cabinet bottom is
less than 3/4” thick.
• Install the filler blocks on each side of the cutout. The
filler blocks will accept the hood mounting screws.
NOTE: Additional filler blocks may be required along the
outside edges to accept the outside screws. See Step 5.
5 REMOVE SIDE SCREW
The top center screw on both sides of the hood can be
used to close up any noticeable gaps at the outside
edges. See illustration.
Cabinet Frame.
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of Cabinet
Recess
Top of Vent
Hood
Remove screw cover
and screw
• Remove the center screw cover and screw on each
side as shown.
IMPORTANT: If filler blocks are not used, the hood may
not be secured to the cabinet.
21
Installation Instructions
UNDER-CABINET INSTALLATION
6 MOUNT THE HOOD
7 COMPLETE THE INSTALLATION
AND CONNECT DUCTWORK
Install a wood screw
on each side of the
mounting frame
Install 2 Screws into
Each Side Bracket
• Carefully, lift the hood into the cabinet. Guide the
hood upwards to meet the ductwork.
• Drive 2 screws into each side bracket.
Be sure the screws engage the filler blocks
or the cabinet bottom.
IMPORTANT: One person must hold the hood in place
while the other drives the screws into the mounting
frame.
• Pull the glass canopy forward to access and install
2 screws through the hood and into the brackets on
both sides.
• Use duct tape to secure the duct to the exhaust
outlet in the top of the hood. Do not use screws
at this location.
Install original top screws
If there is a noticeable gap between the hood and the
bottom of the cabinet on the sides:
• Slide canopy forward and install original top screws
through the bottom of the hood and into cabinet
bottom or frame.
NOTE: Install wood filler blocks if necessary to
accept the screws.
22
Installation Instructions
UNDER-CABINET INSTALLATION
8 CONNECT ELECTRICAL
10 INSTALL FILTERS
WARNING:
If house wiring is not 2-wire
with a ground wire, a ground must be provided by
the installer. When house wiring is aluminum, be sure
to use U.L. approved anti-oxidant compound and
aluminum-to-copper connectors.
• Remove protective film on the filters.
ADVERTISSEMENT :
Si la maison n’est pas câblee avec deux fils et un fil de
terre, l’installateur doit installer un fil de terre. Quand
les fils sont en aluminium, il faut prendre soin d’utiliser
des connecteurs aluminium à cuivre avec une pâte
antioxydante approuvée par U.L.
• Remove junction box cover and knockout.
• Use a conduit connector to secure the conduit to
the junction box.
• Connect white leads to branch circuit white lead.
• Connect black leads to branch circuit black lead.
• Connect green/yellow leads to branch circuit green
lead or bare ground lead.
• Secure all connections with wire nuts on each
electrical connector.
• Push wires into junction box and replace cover.
Be sure wires are not pinched.
• Secure electrical panel cover with screws provided.
Filter Locks
NOTE: It is not necessary to install the charcoal filter
in a vented installation.
• Tip the filter into the slots at the rear of the opening.
Lift the filter lock and pull forward until the filter
rests in the slots.
• Install both metal grease filters.
• To remove the filters, press inwards on the handle
and pull the filter downwards.
9 INSTALL REAR MOUNTING
SCREWS
Install 2 Wood Screws
• Pull the glass canopy forward to access and install
2 wood screws or fasteners through the bottom of
the hood and into the wall.
23
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
Pub. No. 49-80267
10-04 JR
Printed in Italy