GPX TDE1380 User's Guide

Add to my manuals
9 Pages

advertisement

GPX TDE1380 User's Guide | Manualzz

TDE1380

13” HDTV with DVD

For the most up-to-date version of this User’s Guide, go to www.gpx.com

USER’S GUIDE

V:1706-0830-10

Warnings and Precautions

• CAUTION: TO PREVENT ELECTRIC SHOCK,

MaTCH WIDE BLaDE OF PLUg TO WIDE SLOT,

FULLY INSERT.

• WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

• WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.

• AveRTIssemeNT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.

• WARNING: Shock hazard - Do Not Open.

• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS

OUVRIR

• CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.

• WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.

Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely.

La prise du secteur est utilisé pour déconnecter le système.

La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur.

• WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.

• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent.

• WARNING: There is a danger of explosion if you attempt to charge standard alkaline batteries in the unit.

Only use rechargeable NiMH batteries.

• WARNING: The remote control’s button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.

No mezcle baterías viejas y nuevas.

No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE D' ÉLECTROCUTION

NE PAS OUVRIR

WaRNINg: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BaCK). NO USER-

SERVICEaBLE PaRTS INSIDE. REFER

SERVICINg TO QUaLIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This product utilizes a Class 1 laser to read

Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the CD Player’s lid is open and the system’s interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.

2 GPX

Important Safety Instructions

1. Read these Instructions.

FCC Warnings

2. Keep these Instructions.

3. Heed all Warnings.

WaRNINg: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

9. Do not defeat the safety purpose of the polarized or grounding - type plug. a polarized plug has two blades with one wider than the other. a grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.

When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux

éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

• Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely.

La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur.

• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable.

• Caution marking is located at the rear or back of the apparatus.

Attention marquage est situé à l’arrière ou à l’arrière de l’appareil 14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• The marking information is located at the rear or back of apparatus.

Les informations de marquage est situé à l’arrière ou à l’arrière de l’appareil.

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by

Rovi Corporation. Reverse engineering and disassembly are prohibited.

Customer Support: 1-888-999-4215 GPX 3

13” Class HDTV with DVD

Features

• 13.3” LED display

• ATSC/NTSC tuner

• Electronic program guide

• Aspect ratio: 16:9 widescreen

• Resolution: 1280 x 800

• TV supports: 480p, 480i, 720p, 1080i, 1080p

• Viewing angle: 40˚ (H) x 50˚ (V)

• Contrast: 500:1

• Brightness: 200cd/m 2

• Response time: <12ms

• Color: 16.7 million

• V-chip

• Closed captioning

• Multi-language OSD: English, French, Spanish

• Sleep timer

• DVD player: DVD, DVD±R/RW

• CD player: CD, CD-R/RW, JPEG CDs

• SD memory card reader: MP3, JPEG

• USB port: MP3, JPEG

• RF input

• 3 HDMI inputs

• VGA/PC input

• PC audio input

• Component video input

• 2 composite video inputs

• 2 RCA audio inputs

• Stereo headphone jack

• Remote: requires 2, AAA size, batteries

(included)

• DC power input: requires an AC/DC power adpater (included)

• RoHS compliant

Included

• TDE1380

• Remote: requires 2, AAA size, batteries

(included)

• Detachable stand: requires 3 screws

(included)

• AC/DC power adapter

* Please note, LCD panel specifications are subject to change without notice.

4 GPX

Table of Contents

13” Class HDTV with DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features

Included

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power

Remote

TV Stand

Television Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting a TV Antenna

Connecting a Set-Top Box

Connecting Basic Cable

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Auto Scanning for Channels

Channel List View

Adding Favorites

Viewing Favorites

Parental Controls (V-Chip)

Setting the Clock

Television Menu

DVD and CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Loading a DVD or CD

Playing a DVD or CD

Programming a DVD or CD

DVD Setup Menu

Memory Card Slot and USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting a Memory Card

Using a Connected Memory Card

Connecting a USB Thumb Drive

Using a Connected USB Thumb Drive

Connecting Other Devices (Set-Top Box, Gaming Device, DVD Player, VCR, or PC) . . . . . . . . . . . . . . 14

Connecting a Set-Top Box

Connecting a Gaming Device

Connecting a DVD Player or VCR

Connecting a Computer

Company Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

International Support

Contact Information

Green Initiative

Customer Support: 1-888-999-4215 GPX 5

Introduction

VOLUME

Press to adjust the volume.

CHANNEL

Press to adjust the television channel.

DISC DRIVE

USB PORT

SD/MMC/MS

MEMORY CARD

READER

REPEAT

Press to repeat the current chapter or track or the entire disc.

EJECT

Press to eject the loaded disc from the DISC DRIVE.

USB PORT

For firmware upgrades only.

STEREO

HEADPHONE

JACK

DC POWER INPUT

DC IN 12V

REPEAT

/ /

PLAY/PAUSE

Press to play or pause a loaded disc.

SKIP/SEARCH

Press to skip between chapters or tracks. Press and hold to search through the current chapter or track.

STOP

Press to stop a disc during play.

TV

ANTENNA

L

AUDIO 2

R

VIDEO 2

YPbPr

6 GPX

MENU

Press to access the television menu.

POWER

Press to power the television off or on.

SOURCE

Press to adjust the television source.

HDMI INPUTS

VGA/PC INPUT

3.5mm PC AUDIO

INPUT

COMPOSITE

VIDEO INPUT 1

RCA AUDIO

INPUT 1

RCA AUDIO

INPUT 2

COMPOSITE

VIDEO INPUT 2

COMPONENT

VIDEO INPUT

TV ANTENNA

INPUT

POWER

Press to power the television off or on.

POWER MUTE

SLEEP

Press repeatedly to set the sleep timer.

After the set time has expired the television will automatically power off.

ASPECT

Press to adjust the aspect ratio between

FULL, NORMAL, WATERGLASS, and CINEMA.

PICTURE

Press to adjust the picture between

STANDARD, MOVIE, USER, and DYNAMIC.

The user mode can be customized by accessing Picture Settings in the menu.

SOUND

Press to adjust the sound between

STANDARD, SOFT, USER, and DYNAMIC. The user mode can be customized by accessing

Sound Settings in the menu.

VOLUME

Press to adjust the volume.

MENU

Press to view the television setup menu.

AUDIO/SAP

Press to cycle through the available audio settings in DVD mode. In TV mode, press to switch to an alternate audio option when supported.

DISPLAY

Press to view the on-screen display.

FAV LIST/PLAY/PAUSE

In TV mode, press to view your favorites list.

In DVD mode, press to play or pause the loaded disc.

ADD/ERASE/STOP

In TV mode, press to add or erase the current channel as a favorite. In DVD mode, press to stop the current disc during play.

CH LIST/SKIP

In TV mode, press to view a list of available channels. In DVD mode, press to skip between chapters.

AUTO/SKIP

In PC mode, press to fine tune the position of the screen automatically. In DVD mode, press to skip between chapters.

WIDE

In DVD mode, press to switch between

16:9, 4:3 PS, and 4:3 LB.

DVD SETUP

In DVD mode, press to access the DVD setup menu.

PROGRAM

Press to program the loaded disc to play chapters or tracks in a specified order.

USB/SD

In DVD mode, press to switch between USB and SD card mode.

Customer Support: 1-888-999-4215

10+

-

DISPLAY

ANGLE

EJECT

VOLUME

PICTURE

AUDIO

SOUND

SUBTITLE

CHANNEL

SOURCE

FAV LIST ADD/ERASE FAV CH + FAV CH -

CH LIST AUTO

DVD SETUP TITLE DVD MENU

PROG USB/SD REPEAT A-B

MUTE

Press to mute the volume.

NUMBER KEYPAD

ANGLE/PREV

Press to view alternate angles on supported DVDs. In TV mode, press to switch to the previous channel.

FREEZE

Press to freeze or unfreeze the current frame in DVD mode or TV mode.

EJECT/GUIDE

In DVD mode, press to eject the loaded disc. In TV mode, press to view the onscreen television guide.

CHANNEL

Press to adjust the television channel.

SUBTITLE/CC

Press to cycle through available subtitle settings in DVD mode. Press to view the closed captioning in TV mode.

EXIT

Press to exit the current menu.

ARROW KEYS

ENTER

SOURCE

Press to view the available television sources. Press the ARROW and ENTER buttons to adjust the current television source.

FAV CH +/-

Press to cycle through saved favorite channels in TV mode.

ZOOM

In DVD mode, press to zoom in or out on the current screen.

GOTO

In DVD mode, press to go to a specified title, chapter, and time.

SEARCH

Press to search through the current chapter or track.

TITLE

Press to access the title menu on a loaded

DVD.

DVD MENU

Press to access the DVD menu on a loaded

DVD.

A-B

While playing a DVD, press to set a specified section of DVD to repeat.

REPEAT

Press to repeat the current chapter or track or the entire disc.

GPX 7

Setup

Power

Plug the included AC power cable into the DC

POWER INPUT on the television and an AC power outlet to power the television.

Remote

Requires 2, AAA size, batteries (included)

TV Stand

Requires TV stand and screws (included). Use a philips-head screwdriver to tighten the screws.

Using an power drill could damage the TV stand.

8 GPX

OPEN

DC IN 12V

TV

ANTENNA

AUDIO 2

L R

VIDEO 2

YPbPr

Television Setup

Connecting a TV Antenna

Requires a TV antenna (not included).

Connecting Basic Cable

Requires a cable connection.

1. Connect a VHF, UHF, or HDTV antenna to the

RF INPUT on the television.

2. Press the SOURCE button to switch to TV mode.

3. Press the MENU button to access the setup menu.

4. Press the ARROW () buttons to highlight the CHANNEL icon. Press the

ENTER button.

5. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW

() buttons to select AIR.

6. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

1. Connect a cable to the RF INPUT on the television.

2. Press the SOURCE button to switch to TV mode.

3. Press the MENU button to access the setup menu.

4. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

5. Press the ARROW () buttons to highlight

SIGNAL TYPE. Press the ARROW () buttons to select AIR.

6. Press the ARROW () buttons to highlight

AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

Connecting a Set-Top Box

Requires a Set-Top Box (not included).

If your Set-Top Box has an HDMI Output:

• Connect the HDMI output on the Set-Top Box to the HDMI INPUT on the television using an

HDMI cable (not included).

If your Set-Top Box has a Composite Video Output:

• Connect the video output on the Set-Top Box to the COMPOSITE VIDEO INPUT on the television using an A/V RCA cable (not included). Connect the audio output on the Set-Top Box to the RCA AUDIO INPUT on the television.

If your Set-Top Box has a Component Video Output:

• Connect the component video output on the Set-Top Box to the COMPONENT VIDEO INPUT on the television using a component RCA cable (not included). Connect the audio output on the

Set-Top Box to the RCA AUDIO INPUT on the television.

After connecting your Set-Top Box:

• Press the SOURCE button to switch to YPbPr, AV1 or AV2, or HDMI 1, 2, or 3 to match the connection used.

Customer Support: 1-888-999-4215 GPX 9

Television

Auto Scanning for Channels

The Auto Channel Scan must be run before any channels can be viewed on the television.

1. Press the SOURCE button to switch to TV mode.

2. Press the MENU button to access the setup menu.

3. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

4. Press the ARROW () buttons to highlight SIGNAL TYPE.

Press the ARROW () buttons to select AIR.

5. Press the ARROW () buttons to highlight AUTO CHANNEL

SEARCH. Press the ENTER button to begin scanning for available channels.

Channel List View

1. Press the SOURCE button to switch to TV mode.

2. Press the CH LIST button, on the remote, to view a list of available channels.

Unless you are using a Set-Top Box, you must auto scan for channels before being able to view channels in list view.

Adding Favorites

1. Press the SOURCE button to switch to TV mode.

2. Press the CHANNEL buttons to select the desired TV channel.

3. Press the ADD/ERASE button to add or erase the current channel as a favorite.

Viewing Favorites

1. Press the SOURCE button to switch to TV mode.

2. Press the FAV LIST button to view a list of your saved favorites.

Parental Controls (V-Chip)

1. Press the SOURCE button to switch to TV mode.

2. Press the MENU button.

3. Press the ARROW () buttons, highlight PARENTAL, and press the ENTER button.

4. The default passcode for the parental lock is: 0 0 0 0

5. Enter the passcode to access the PARENTAL CONTROL preferences.

6. From this menu, you can lock specific ratings from the

United States rating system or the Canadian rating system by accessing the V-CHIP settings. You can also lock the buttons on the television or lock specific sources from access.

10 GPX

Setting the Clock

1. Press the MENU button to access the setup menu.

2. Press the ARROW () buttons to highlight the SETUP icon. Press the ENTER button.

3. Press the ARROW () buttons to highlight CLOCK. Press the ENTER button.

4. Press the ARROW () buttons to highlight TIME ZONE. Press the ARROW

() buttons to select your current time zone.

5. Press the ARROW () buttons to highlight AUTO CLOCK. Press the ARROW

() buttons to turn auto clock off and on.

When the correct time zone is set, auto clock will automatically set your clock and date for you.

6. To set the time and date manually, turn auto clock off, highlight SETUP TIME, and use the

ARROW and ENTER buttons to manually set the time and date.

Television Menu

Press the MENU button to access the TV menu.

Press the EXIT button to exit the TV menu.

Picture

Picture Settings

Screen Settings

PC Settings

Color Temperature

Advanced Picture Settings

Sound

Sound Settings

Surround Mode

Analog Sound

Digital Sound

Other Settings

Channel

Channel List

Favorite List

Channel Setting

Signal Type

Auto Channel Search

Parental

Lock Parental Control

V-Chip

Change Password

Front Panel Lock

Source Lock

Setup

Closed Caption

Menu Languag

Clock

Others

Blue Back

No Signal Power Off

No Operation Power Off

All Reset

Audio Only

Customer Support: 1-888-999-4215 GPX 11

DVD and CD

Loading a DVD or CD

1. Gently insert a DVD or CD into the slot-load disc drive, with the label side of the DVD or

CD facing the back of the television.

Once a DVD or CD is loaded into the television, the TV will automatically switch to DVD mode.

Playing a DVD or CD

1. Follow the instructions for Loading a DVD or

CD.

2. After the DVD or CD is loaded, it will begin playing automatically.

If the DVD or CD does not begin playing

automatically, press the PLAY/PAUSE button to begin playing the loaded disc.

Programming a DVD or CD

1. While a DVD or CD is playing, press the

PROGRAM button on the remote.

2. Using the NUMBER KEYPAD enter in the title

(T) and chapters (C), or tracks in the order you want them to play.

3. Highlight the on-screen PLAY button using the ARROW buttons and press the ENTER button.

4. The programmed titles and chapters, or tracks will now play in the designated order.

5. To cancel a program, press the PROGRAM button, highlight the on-screen CLEAR button using the ARROW buttons, and press the ENTER button.

DVD Setup Menu

In DVD mode, press the DVD SETUP button to access the DVD setup menu. Press the DVD

SETUP button to exit the DVD setup menu.

System Setup

TV System

Screen Saver

TV Type

Power Resume

Default

Exit Setup

Language Setup

OSD Language

Audio Language

Subtitle Language

Menu Language

Exit Setup

Audio Setup

Key

Exit Setup

Digital Setup

Dynamic Range

Dual Mono

Exit Setup

Memory Card Slot and USB Port

REPEAT

/ /

Connecting a Memory Card

1. Load an SD, MS, or MMC memory card into the MEMORY CARD READER as shown in the image to the right.

Using a Connected Memory Card

1. Follow the instructions for Connecting an SD or MMC card.

2. Press the SOURCE button to switch to DVD mode.

3. Press the USB/SD button on the remote to switch to the connected memory card.

4. Use the ARROW and ENTER buttons to select and play content from the connected memory card.

Connecting a USB Thumb Drive

1. Load a USB thumb drive into the USB PORT as shown in the image to the right.

Using a Connected USB Thumb Drive

1. Follow the instructions for Connecting a USB thumb drive.

2. Press the SOURCE button to switch to DVD mode.

3. Press the USB/SD button on the remote to switch to the connected USB thumb drive.

4. Use the ARROW and ENTER buttons to select and play content from the connected USB thumb drive.

REPEAT

/ /

12 GPX Customer Support: 1-888-999-4215 GPX 13

Connecting Other Devices (Set-Top Box, Gaming Device, DVD Player, VCR, or PC)

Connecting a Set-Top Box

• You will need: a set-top box, s-video and RCA stereo cables or composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

• Connect the set-top box’s audio and video

outputs to the corresponding audio and video inputs on the television.

• Power the television on and press the

SOURCE button to switch to the connected input. (AV1 or AV2, YPbPr (Component), or

HDMI 1, 2, or 3)

Connecting a Gaming Device

• You will need: a gaming device, s-video and

RCA stereo cables or composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

• Connect the gaming device’s audio and video

DC IN 12V outputs to the corresponding audio and video inputs on the television.

• Power the television on and press the

SOURCE button to switch to the connected input. (AV1 or AV2, YPbPr (Component), or

HDMI 1, 2, or 3)

Connecting a DVD Player or VCR

• You will need: a DVD player or VCR, s-video and RCA stereo cables or composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable.

• Connect the DVD player or VCR’s audio and

DC IN 12V

video outputs to the corresponding audio and video inputs on the television.

• Power the television on and press the

SOURCE button to switch to the connected input. (AV1 or AV2, YPbPr (Component), or

HDMI 1, 2, or 3)

TV

ANTENNA L

AUDIO 2

R

VIDEO 2

TV

ANTENNA

L

AUDIO 2

R

VIDEO 2

YPbPr

YPbPr

Composite 1 and

RCA stereo

Composite 2 and

RCA stereo

Component and

RCA stereo

HDmI

Connecting a Computer

• You will need: a PC with a VGA output, and a

VGA cable. (not included)

• Connect the computer’s VGA output to the

VGA/PC INPUT on the television.

• Power the television on and press the

SOURCE button to switch to the PC Mode.

• Audio from the connected PC can be input to the television through the TV’s PC AUDIO

INPUT by using a 3.5mm audio cable (not included).

14 GPX Customer Support: 1-888-999-4215 vGA/PC INPUT

PC Audio Input

GPX 15

Company Information

International Support

To download this User’s Guide in English,

Spanish, or French, visit the support section at www.gpx.com.

Para transferir esta guía de usuario en inglés, español, o francés, visite la sección de la ayuda en www.gpx.com.

Pour télécharger ce guide de l’utilisateur en anglais, espagnol, ou français, visitez la section de soutien chez www.gpx.com.

Contact Information

Phone:

1-888-999-4215

Email: [email protected]

Parts Email: [email protected]

Website: www.gpx.com

Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners.

Specifications are subject to change without notice

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement