Guardian Technologies R3010 User's Manual

USE & CARE INSTRUCTIONS
S tart
Ultrasonic Digital
Humidifier
Remanufactured
Model No. R3010
30-Day Limited Warranty
www.guardiantechnologies.com
1.866.603.5900
English
Spanish E-1
S-1
Date Purchased
month ________
year _________
E-1
CONTROL PANEL BUTTON FUNCTIONS
PRODUCT SPECIFICATIONS AND PARTS
Night Light/Lamp
Model Number: R3010
Humidifying Mode: Combination
Power Supply: AC120V, 60Hz
Power Consumption: 140W (40W at cool humidification)
Humidity Capacity: About 350 cc/hr. (at highest setting and warm humidification)
Tank Capacity: 1.4 gallons
Successive Humidity Hours: Up to approximately 72-hours depending on
environmental conditions
Dimensions: Width 14.5 inches - Height 12 inches - Depth 9 inches
Weight: 8.8 pounds (not including packaging)
Provides a soft ring of blue light
with ON/OFF switch.
Night Light/Lamp
Select/Set
Lamp
Change between programming
mode and normal mode.
Hour
Select the hour for timer start/off
or clock (actual time).
Minute
Select/Set
Start
S top
Time
Select/Set
Select the minute for timer start/
off or clock (actual time).
Power
Hour
Hour
C
Minute
Minute
Turns humidifier on/off for normal
usage and programming mode.
Display
Cool/Warm
Power
Power
Display
On/Off
Spray
ontrol
Spray
Control
Warm or Cool
Mist Selection
Warm or Cool Mist Selection
Spout
Select humidifying temperature based on need. Warm humidity
will use more power but will humidify your room quicker.
Spray Control
Handle
Adjusts spray between low, medium, high and turbo.
Display On/Off
Turns off display lights.
Tank Lid
Tank
Water Shortage Indicator
When the unit is low on water the Refill LED on the front panel will light
up, and the unit will shut off. Simply add more water to continue use.
*To access
cleaning brush,
pull up on lid.
ADDITIONAL FEATURES
Spout Guide
Cleaning Brush
Silver Clean Technology
Small silver particles have been added to the water tank to help fight the growth of mold and mildew on
the surface of the water tank.
Silent Operation
Power Plug
Air-Cleaning Filter
Uses ultrasonic technology for quiet operation while you sleep.
Night Lamp
Body
E-2
E-3
WARNINGS
This product should be used only in accordance with the specifications outlined in this manual.
Usage other than what has been specified here may result in serious injury.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Disassembly, repair or remodeling by an unauthorized person may result in serious harm.
Do not use if plug is damaged or loose.
Keep this product out of the reach of children and away from pets.
Be careful not to put water in the humidity spout.
Before filling or cleaning the unit, make sure it is unplugged.
Once the humidifier has been turned on, do not move it.
Do not move when in operation.
Do not remove the water tank from the unit while it is on.
Do not handle the adapter plug with wet hands.
Do not excessively bend, twist or pull the power cord.
Avoid placing this product where the humidity is pointed directly at an electrical object.
Do not directly inhale the humidity.
Do not place this product on a sloped or unstable surface.
When not in use, unplug the unit.
Do not fill the water tank with hot or boiling water.
Do not use this product in direct sunlight, or near a gas stove or heater.
Do not use if the water tank becomes cracked or damaged.
Do not keep this product running for an extended period of time.
Do not clean the unit or water tank with detergents or chemicals of any kind.
Do not use this product near any other electronic device.
Do not cover the humidity opening at any time during use.
Do not use this product near a sink.
Do not drink water from the water tank.
Do not place this product on an absorbent surface.
Do not pour anything but water into the water tank.
Make sure the unit is unplugged.
1. Separate the tank from the body
2. Open the tank lid, turning it to
3. Pour cool, clean water directly
4. Close the tank lid, turning it to
of the unit.
into the tank. Do not pour anything but water into the water tank.
the left.
the right.
Failure to comply with the warnings listed above may result in electric shock or serious injury.
5. Attach the tank to the body of
the unit.
E-4
E-5
1. Power Button
Before turning on make sure there is water in the unit.
Press the Power Button.
The programmable mode allows you to set the timer to turn the humidifier both on/off
at a daily predetermined time. This mode also allows the clock to be programmed.
FIRST TURN POWER BUTTON ON.
P ower
S tart
Sp
C
2. Warm or Cool Mist Button
Press to select warm or cool mist. Water
temperature is maintained at room temperature for cool
setting and 80 degrees for warm.
Spray
Control
Display
Select/Set
Time
Hour
Minute
3. Spray Control Button
When you press the Spray Control Button
there are four options to choose from:
4A. Light Options - Display Button
Press the Display Button to turn the display lights ON or OFF.
Program Stop
1. Push Select/Set Button until "STOP" is blinking on display.
2. While "STOP" is blinking, select the desired end time using Hour and
Minute buttons (AM or PM as indicated).
3. "STOP" indicator will remain lit once programmed.
4. To cancel program, press and hold select/set button for two seconds
(START and STOP buttons will not be lit).
Press once for WEAK
Press twice for MIDDLE
Press three times for STRONG
Press four times for TURBO
*You will notice the lights get higher as the spray increases.
4B. Light Options - Night Light Feature
Press the Lamp Button at the top of the unit to illuminate
the night light feature.
Lamp
r
S top
Program Start
1. Push Select/Set Button until "START" is blinking on display.
2. While "START" is blinking, select the desired start time using Hour and
Minute buttons (AM or PM as indicated).
3. Select Cool/Warm preference.
4. Select Spray Control preference.
5. "START" indicator will remain lit once programmed.
Cool/W arm
Dim
Done
set
Clock Set
1. Clock must be set in order for timer to work properly.
2. Push Select/Set Button until "TIME" is blinking on display.
3. Select actual time using Hour and Minute Buttons (AM or PM as indicated).
5. Water Refill Button
When the Water Refill Button lights up it is time to refill
the water tank.
E-6
E-7
•
•
•
Always unplug the unit before servicing it in any way.
The temperature of the water remaining in the unit after use may be HIGH.
Do not submerse the unit in water, or allow water to enter anywhere on the unit
except the designated water tank.
PROBLEM
SOLUTION
Water vapor & humidity are
not produced.
Power Plug: Unplug and then try again.
Tank Installation: Make sure the water tank is
correctly attached. Make sure spring on tank
cap moves freely when pushed.
INSIDE THE BODY OF THE UNIT
Pour excess water out of the unit, but do not allow it to enter the hole where the water
vapor comes out. Wash out the unit with fresh water, using the cleaning brush and a
soft cloth as needed.
OUTER SURFACE OF THE UNIT
Wipe the surface of the unit with a soft, damp cloth if needed.
Air blows but water vapor is
not produced.
Excessive Water: Remove a certain amount of water
from the tank.
The desired humidity is lower than the current temperature: Increase the desired humidity.
WATER TANK
If water spots remain in the water tank, wipe the inside with a soft cloth.
DO NOT use soap or detergents.
Detergent residue in the tank: Wash the tank out and
try again.
AIR FILTER
Gently wipe away debris from the filter with a soft cloth.
This filter does NOT need to be replaced.
Power Failure: When the power is returned, try again.
Humidity level is low.
The surface of the ultrasonic metal disk may be dirty:
Wipe it off with a dry, soft cloth. Clean with diluted
vinegar.
The water in the unit is too cold: Replace with cool,
but not cold water.
ULTRASONIC DISK
Remove spray spout (Fig. 1) and use the enclosed cleaning brush to regularly remove build up
and deposits from this area (Fig. 2). Diluted vinegar will help to prevent this build up.
Warm humidity is not produced.
It may take 10-15 minutes before warm
humidity is created. The mist may not feel
warm to the touch.
Check to see if base of unit feels warm to the touch.
If so then warm mist is being produced.
Fig. 1
•
•
•
E-8
Fig. 2
Fully dry the inside and outside of the unit before storing it.
DO NOT leave water in the unit.
Store in a cool, dry place.
The humidity has a bad smell.
Poor maintenance or dirty water: Clean the product
thoroughly, and fill it with fresh water.
White dust is forming on
nearby furniture.
Hard water will deposit a certain amount of
dust. Dust in the air settles because of the
added humidity in the room.
*Use distilled water if this becomes a nuisance.
E-9