advertisement
AUTOMATIC DRUM WASHING MACHINE
USER MANUAL
HW70-B1486-F
HW70-B1286-F
HW80-B1486-F
HW80-B1286-F
Wash
Wash
Rinse
Temp.
Temp.
Speed
Auto Spin
Strong wash
Delay
Pre-wash Soak
Heavy
Silk
Heavy
Silk
Wool
Synthetic
Memory
Cotton
Start / Pause
Press and hold 2seconds to set door unlocked
Sport wash
Delicate
Sport wash
Silent
Quick
Spin
Self-clean
Power
03 - 09
TABLE OF CONTENTS
10 - 15
16- 20
BEFORE USE USING THE APPLIANCE
> COMPONENTS
> PREPARATION
............................... 03
................................ 04
> SAFETY INSTRUCTIONS
> INSTALLATION ................................ 06
> CONTROL PANEL
................... 05
............................ 08
> PROGRAM SELECTION
> CONSUMPTION AND TECHNICAL DATA
> WASHING METHODS
> CLEANING & CARE
..................... 10
.. 11
...................... 12
.......................... 16
MAINTENANCE
> DISPLAY CODES ............................. 18
> TROUBLESHOOTING ........................ 19
LEGEND
Yes
No
Optional
For your safety, any instructions in this manual with this "Warning" sign must be followed strictly.
BEFORE USE
COMPONENTS
THANKS FOR PURCHASING A HAIER PRODUCT
03
Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance.
Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings.
ACCESSORIES
Check the accessories and literature in accordance with this list:
1x Inlet hose assembly
1x User manual
1x Bottom Cover
AUTOMATIC DRUM WASHING MACHINE
Wash
Rinse
Spin
Strong wash Delay Pre-wash
Temp.
Speed
Auto
Soak
Heavy
Synthetic Wool
Cotton Memory
Start / Pause Press and hold 2seconds to set door unlocked
Delicate Sport wash
Silent Quick Power
Self-clean Spin
1x Drain hose bracket
4x Blanking plugs
04
PREPARATION
PREPARING THE MACHINE
BEFORE USE
Remove all the packing materials to prevent unsteadiness, including the polystyrene base. Upon opening the package, water drops may be seen on the plastic bag and the porthole. This is normal phenomenon resulting from water tests in the factory.
DESCRIPTION
This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements.
Control panel
Power
Work top
Washer door
Door handle
Detergent distribution drawer
Filter cover
Wash
Rinse
Spin
Strong wash Delay
Temp.
Speed
Pre-wash
Auto
Soak
Heavy
Silk
Wool
Synthetic
Memory
Cotton
Start / Pause
Press and hold 2seconds to set door unlocked
Delicate
Sport wash
Silent
Quick
Spin
Self-clean
Power
Drain hose
Water inlet valve
Power cord
Back cover screws
Back cover
Transportation bolts
T3
S1
T4
T1
S2 S4
S3
T2
SAFETY INSTRUCTIONS
BEFORE USE
05
BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME
... Make sure that the transport bolt are removed.
... Use a separate earthed socket for the power supply.
... Make sure that the plug is accessible.
... Hold the plug and not the electric cable when unplugging the power supply.
... Make sure that the fuses in the power circuit are rated for 15A.
... Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging.
... Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable.
... Check that hose joints and connections are fi rm and no water can leak. If joints are loose or there is leakage, turn off the water supply and refi x. Do not use the washing machine until the hoses are properly fi xed.
DO NOT ...
... Touch or use the appliance when barefoot or with wet or damp hands or feet.
... Use fl ammable detergent or dry cleaning agent.
... Use any fl ammable sprays in close vicinity to the appliance.
... Remove or insert the plug in the presence of fl ammable gas.
... Allow children or infi rm persons to play with the appliance or packing materials.
... Install the appliance outdoors in a damp place, or in an area which may be prone to water leaks such as under or near a sink unit. In the event of a water leak allow the machine to dry naturally.
... Place the washing machine directly on a carpet, or close to a wall or furniture.
DURING DAILY USE OF THE APPLIANCE
... Pull up zips and fi x loose threads to prevent the items from being entangled. If necessary, put small items into a net bag or pillow.
... Turn off the machine after each wash program and switch it off at the mains to save electricity and for safety. Wipe clean the lower part of the porthole.
... Keep the door slightly open when the washing machine is not in use to prevent formation of odours.
... Let the power cord be replaced by the manufacturer, his service agent or other accordingly qualifi ed persons, in case it is damaged.
... Ensure that the appliance is not used by persons with reduced physical, sensory or mental capabilities, lack of experience and knowledge without supervision or instruction by a person responsible for their safety.
... Supervise children to ensure that they do not play with the appliance.
DO NOT ...
cycle.
... Touch the washer door during the washing process - it gets hot!
...Place heavy objects or sources of heat or damp on top of the appliance.
... Hot wash foam rubber or sponge-like materials.
... Open the detergent distribution drawer during the wash
... Force the washer door open. The door is fi tted with a self-lock device and will open shortly after the washing procedure is ended.
... Open the washer door if the water level is visibly over the porthole.
... Cover the washing machine with plastic cover so that inside dampness cannot be kept in.
06
INSTALLATION
BEFORE USE
DISMANTLE THE TRANSPORTATION BOLTS
The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process.
1.
Remove the back cover.
2.
Remove the four bolts on the rear side and take out the synthetic stabilisers from within the machine.
3.
4.
Note:
Replace the back cover.
Fill the holes left by the bolts with blanking plugs.
1.When you replace the back cover,the convexity must face to outside, and you have to insert the back cover from the two gaps as shown in fig.5.
2.Keep the transportation bolts and synthetic stabilisers in a safe place for later use.
5.
ADJUSTING THE WASHING MACHINE
There are adjustable feet under the bottom of the washing machine. Before use, they should be adjusted so that the machine is level. This will minimise vibrations and thus noise during use. It will also reduce wear and tear. We recommend using a spirit level to level the appliance.The floor should be as stable and flat as possible.
BEFORE USE
INLET HOSE
1. Connect the nut on the inlet hose to the connector on the water valve.
2. Apply inlet hose to a water tap with cold, fresh water.
Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused.
1.
2.
DRAIN HOSE
1. Use the drain hose bracket to keep the end of the drain hose retained and prevent the outfl ow of water. Don't extend the length of the drain hose; if an extended hose is required, please consult a serviceman.
2. The height of the drainage outlet must be 80-100 cm. Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off.
1.
2.
Note: The drain hose should not be submerged in water and should be securely fixed and leak-free. If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm, the washing machine will continuously drain while being filled (self-siphoning).
CONNECTING TO THE POWER SUPPLY
Before connecting to the power supply, check:
¬ The socket is adequate for the maximum power of the washing machine
(For safety, fuses in the power circuit should be rated for no less than 15A).
¬ The voltage should meet the requirement.
¬ The power outlet should be capable of accepting the washing machine plug.
¬ Connect the machine to an earthed socket outlet.
07
08
CONTROL PANEL
J
BEFORE USE
I HG F E DC
Wash
Rinse
Spin
Intense
Temp.
Speed
Prewash
Rinse Hold
C o t t o n
M1
S y n t h e t i c
M2
M i x
M3
D e il c a t e
W o o l
H a n d W a s h
Start/pause
B
D a li y W a s h
S p o r t 2 5 '
E x p r e s s 1 5 '
J eans
B a b y Care
S p i n / D r a i n
Power
A
A Power Switch
B Program knob
C M emo button
D Spinning Speed Setting button
E Washing temperature button
K L M N O
F Display screen
G Washing time
J
I
H Times of rinse
Spinning time
Detergent distribution drawer
K
Intense washing button
L
End Delay
Button
M Pre-wash button
N
Rinse Hold button
O Start/
A ¬ Power
Switch
_ Press this button to switch on the washing machine. Press it again to switch it off.Press On/Off button gently for finishing the program. It will change to power off station if there is no operation on the button and none will be shown.
C ¬
M emo button
This function could be used under the programmes cotton/Synthetic/Mix. After choosing one of these, the user can set washing time washing temperature rinse times spin speed spin time and choose some additional function such as Intense/Delay/Prewash/Rinse hold according as her need or habit Finish them then keep pressing
“memo” button for 2 seconds, the display screen will show the corresponding number ( 1 stands for the programme have
been setting under cotton; 2 stands for the programme having been setting under synthetic; 3 stands for the programme having been setting under Mix) . It means the programme choosing by users have been saved. Next time ,when user choose one of these Cotton/Synthetic/Mix, then press “Memo” ,the corresponding programme having been saved will be called out, press “Start/pause” button to perform this programme. Also, the setting programme can be used many times until the user set a new one, the previous programme will be covered.
E ¬ Washing temperature button heating temperature varies with programs.
Note:“--” in the temperature display indicates non-heated washing.
BEFORE USE
09
F Display screen
_Display washing time, remaining time, times of rinsing, spinning time, temperature setting value, speed setting value, child lock state, door lock state, washing progress and alarm message, etc.
G Washing time Press the “Wash” button to set washing time. Press and hold this button to change the time continuously. Click this button up until the end.
Note: This function is not applicable to “ Spin/Drain ” process
H Times of rinse Press the “Rinse” button to select the times of rinsing and the maximum allowable times of rinsing is 8.
I Spinning time Press the “Spin” button to select spinning time. The maximum allowable spinning time varies with programs.
J ¬ Detergent distribution drawer
_Open the drawer, three compartments can be seen:
Compartment 1: Prewash detergent
Compartment 2: Detergent for programs 1 to 10.
Compartment 3: Softener, conditioning agent, perfume, etc.
2
2
3
1
1
The recommendation on the type of detergents is suitable for the various washing temperatures, please refer to the manual of detergent.
L
K
Intense washing button
M
¬End Delay
Button
Pre-wash button
Press "Strong wash" button to increase the washing time during the main washing stage of selected program.(This feature is applicable for dirty clothes ) The illuminated icon indicates the “strong wash” function is selected. This additional function applies to “cotton”, “memory”, “synthetic” ,“Silent” “heavy”and
“Sport wash” programs only. This button is effective before starting a program.
Press the “Delay” button and the illuminated icon indicates that the “delay” function is selected. The delay time
(0.5-24h) increases by 30 minutes each press of “Delay” button. The time will change continuously if you press and hold this button until you release it. The delay time is the end time of washing. For example, 6:00 means the washing ends after 6 hours (the delay time must be longer than the program’s running time). The “Delay” function is not available for “Spin” and “Self-clean” programs.
Note:The delay time must be longer than the program time;otherwise,the washing machine will start the wash program directly.
Press the “Pre-wash” button to select or cancel the prewash program. The prewash program can be selected for washing heavily soiled clothes. Press the “Prewash” button, the “Pre-wash” icon will illuminate. Press the
“Pre-wash” again, the prewash function will be cancelled and the “Pre-wash” icon will go out. When selecting the prewash function, add a proper amount of detergent into the prewash box, otherwise do not add any detergent into the prewash box. This additional function applies to “cotton”, “memory”, “synthetic” and “Sport wash” programs only
N
Rinse Hold
button rinse, the washing machine is not going to drain, clothes will be soaked in water, and the soak icon flashes, the remain
O
¬ Start/
Pause Button then the icon will be off to cancel this function, and the washing machine continue to work. This feature and the
"End Delay"button can not be chose at the same time. Also this feature is only effective in the “cotton”,
“synthetic”, , “Delicate”, “Sport 25‘ ”, “Jeans” process.
_ Press the “Start/pause” button, the washer will start and the indicator light remains on. If this button is pressed when the washer is in operation, the washer will pause and the indicator light will flash.
10
PROGRAM SELECTION
PROGRAM MODES
USING THE
APPLIANCE
2
2
2
3
1
1
1 Detergent compartment for prewash mode
2 Detergent compartment
3 Compartment for softener and
other additives
Program
Temperature
Maximum Preset
1 ¬ Hand Wash - - to 40 °C 30°C
2 3 1
2 ¬ Wool - - to 40 °C 30°C
3 ¬ Delicate - - to 40 °C 30°C
Recommended
Laundry
Cotton fabrics
Woolen fabrics
Cotton fabrics
4 ¬ Mix - - to 40 °C 40°C
5 ¬ Synthetic - - to 60 °C 40°C
6 ¬Cotton - - to 90 °C 60°C
7 ¬ Daily Wash - - to 60 °C 40°C
8 ¬ Sport 25’ - - to 40 °C 30°C
9 ¬ Express 15‘ - - to 40 °C --- ---
10
¬
Jeans
- - to 60 °C 40°C
11 ¬ Baby Care - - to 90 °C 80°C
12
¬ Spin/Drain
Cotton or synthetic
Chemical fiber fabrics
Cotton fabrics
Cotton fabrics
Sports wear
Cotton or synthetic
Jeans
Cotton or synthetic
None
Preset spin speed
800 rpm
600 rpm
800 rpm
1000 rpm
1000 rpm
1000 rpm
1000 rpm
800 rpm
800 rpm
1000 rpm
1000 rpm
1000 rpm
Yes No Optional
USING THE
APPLIANCE
CONSUMPTION AND TECHNICAL DATA
CONSUMPTION TABLE
PROGRAM
MAX. LOAD
HW70-*86-F/HW80-*86-F
TEMPERATURE
2kg/2 kg ¬ Hand Wash
¬ Wool
30°C
30°C
¬ Delicate
¬ Mix
¬ Synthetic
2kg/2 kg
2kg/2 kg
5 k g / 5 k g
30°C
40°C
¬Cotton
¬ Daily Wash
¬ Sport 25’
3 .
5 k g / 4 k g
7kg/8 kg
3.5kg/4 kg
40°C
60°C
40°C
30°C
¬ Express 15‘
¬
Jeans
¬ Baby Care
¬ Spin/Drain
3.5kg/4 kg
2kg/2 kg
3 .
5 k g / 4 k g
3 .
5 k g / 4 k g
/
-- --
40°C
80°C
/
A u t o
Auto
0:41
0:25
0:15
0 : 5 8
1 : 53
0:08
0:38
0:35
0:38
A u t o
11
WASHING TIME
SPIN DRYING PERFORMANCE
HW*-1286-F/HW*-1486-F
53%/51%
The standard 60 °C and 40 °C cotton programmes are suitable to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumptions for washing that type of cotton laundry;The actual water temperature may differ from the declared cycle temperature;
TECHNICAL DATA
Power source
Max. working current (A)
Water pressure (MPa)
Nominal load (kg)
Spinning speed (r/min)
Washing programs
Max power (W)
Dimensions (HxDxW mm)
Net weight (kg)
Power consumption of the off-mode(W)
Power consumption of the left-on mode(W)
HW70-B1286-F/HW70-B1486-F
220 - 240V~/50Hz
10
0.03≤P ≤1
7
1200/1400
12
2000
850 x x
70
0.39
0.39
HW80-B1286-F/HW80-B1486-F
220 - 240V~/50Hz
10
0.03≤P ≤1
8
1200/1400
12
2000
850 x x
74
0.39
0.39
12
WASHING METHODS
PLEASE NOTE
USING THE
APPLIANCE
This washing machine is for domestic use only. If the machine is use for commercial purpose the guarantee will not be valid anymore.Do not use it for purposes other than that for which it was designed. Follow the instructions given on the label of each garment and wash only machine-washable garments.
POWER SUPPLY
Connect the washing machine to the power supply (220V to 240V~/50Hz).
WATER CONNECTION
Turn on the tap. The water must be clean and clear.
Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap.
PREPARING THE LAUNDRY
¬ Sort out clothes according to fabric (cotton, synthetics, wool or silk) and to how dirty they are.
¬ Separate white clothes from coloured ones. Wash them first by hand to check if they fade or run.
¬ Empty pockets(clips,coins,keys,etc.)and remove the harder decorative objects(e.g. brooches) to avoid
them entrying the drain pump and blocking.
Attention: Small parts (like buttons, etc) may lead to repair work which user has to pay by themselves and can cause damage in the machine.
¬ Garments without hems, underwear, finely woven textile such as fine curtains are to be put into wash bag (it is better not to wash them in a washing machine).
¬ Close zippers and hooks, make sure the buttons are sewn on tightly and place small items such as socks, belts, bras, etc. in the wash bag.
¬ Unfold large pieces of fabric such as bed sheets, bedspreads, etc.
¬ Turn shirts inside out.
USING THE
APPLIANCE
13
LOADING THE MACHINE
Open the washer door, put in the laundry piece by piece. Close the door tightly.
¬ When first using the washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine. Before washing you should run the machine without laundry, but with detergent, with 60°C programm.
¬ Do not overload the washing machine.
SELECTING DETERGENT
The washing efficiency and the performance is determined by the quality of detergent used. Special non-foaming detergent produces good washing results. Use specific detergents for synthetic and woollen goods. Do not use dry cleaning agents such as trichloroethylene and similar products.
Note: Do not add more detergent than needed; otherwise, it may cause the situations as following and washing machine malfunction impacting washing machine’s life.
1.Due to the increasing foam, the rinse time will be longer than normal;
2.The foam may overflow from the detergent drawer because of the increasing pressure of the foam;
3.It may remain foam without cleaning out after the final spinning cycle.
Recommendation:
1.Clean the detergent drawer once a week.
2.When using the prewashing program, please add half of the rating dosage.
3.Please follow the dosage recommendation on the powder or liquid detergent package.
ADDING DETERGENT
Wash
Rinse
Spin
Temp.
Speed
Auto
Strong wash Delay Pre-wash Soak
Heavy
Silk
Wool
Synthetic
Memory
Cotton
Start / Pause
Press and hold 2seconds to set door unlocked
Delicate
Sport wash
Silent
Quick
Spin
Self-clean
Power
Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments. Push back the drawer gently. (Refer to the instructions on the drawer)
2
2 3
Caution: 1
1
¬ For prewashing program, detergent should be added to both compartments 1 and 2.
For other programs, do not add detergent to compartment 1.
¬ Add liquid detergent to the main drawer,and dilute it first if it is concentrated .Do not overuse detergent;otherwise, it will damage the artificial fibers.so,please follow the instructions on the detergent package. Do not use liquid detergent if the pre-wash mode or "End delay" is selected.
¬ Do not overuse softener; otherwise, it will damage the artificial fibers.
SELECTING PROGRAM
To get the best washing results, an appropriate washing program should be selected according to the laundry type. Please turn the program knob to select the right program.
Wash
Rinse
Spin
Temp.
Speed
Intense
M emo
Prewash
Rinse Hold
C o t t o n
M1
S y n t h e t i c
M2
M i x
M3
D e il c a t e
W o o l
H a n d W a s h
Start/pause
D a li y W a s h
S p o r t 2 5 '
E x press15 '
J eans
B a b y Care
S p i n / D r a i n
Power
SELECTING FUNCTIONAL
Select the required options. (Refer to the "Control panel" pages 08 and 09)
14
USING THE
APPLIANCE
SETTING WASHING TEMPERATURE
Press and hold down the temperature button until the desired temperature is selected .
SETTING SPIN SPEED
Press and hold down the speed button until the desired speed is selected.See "Operational functions" on the "Control panel" pages (08 and 09) for selecting temperature and spin speed. It is advisable to select the recommended value.
WASHING
Press the Start/Pause button. The washing machine will operate according to the preset programs. The washing machine will stop operation automatically when a washing cycle ends. The "End" sign will appear on the display. Open the washer door and take out the laundry.
I n t e n s e Fin différée Prélavage A r r t c u v e p l i n e
C o t n M1 n t é t q u e
M2
Mixte
M3
D é il c a t
Laine
Lavage main
Départ/Pause
I n t e n s e
M
Fin différée Prélavage A r ê t c u v e p l e i n e
C t o n M1 n t h é t q u e
M2
Mixte M3 a t
Laine
Lavage main
Départ/Pause
I n t e n s e Fin différée Prélavage A r ê t c u v e p l e i n e t n
M1
S n t é t q u e
M2
Mixte
M3 il c a t
L a i n e
Lavage main
Départ/Pause
AFTER WASHING
Turn off the water supply and unplug the power cord. Open the washer door to prevent formation of moisture and odours. Let the door open while not used.
TIPS FOR SAVING ENERGY
1.
2.
3.
Collect clothes for one full wash load.
Avoid overloading the washing machine.
Prewash only heavily soiled clothes.
4.
5.
Reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes.
Choose a proper washing temperature. Modern detergents can wash with very good result already in lower temperature than 60°C. Only use higher temperature than 60°C for heavily soiled laundry.
6.
Follow the dosage recommendation on the detergent package to avoid using too much detergent.
WARM TIPS:
Q u o t i i n
S p o r t 2 5
Express15'
J e a n s
Bébé coton
Essorage
Vidange
Marche / Arrêt
Power o t d i e n
S o 2 5
Express15'
J e a n s
Bébé coton
Essorage
Vidange
Marche / Arrêt
Power o t d i e n o r t 2 5
Express15'
J e a n s
Marche / Arrêt
Power
Essorage
Vidange
Wash
Rinse
Spin
Temp.
Speed
Auto
Strong wash Delay Pre-wash Soak
Heavy
Silk
Wool
Synthetic
Memory
Cotton
Start / Pause
Press and hold 2seconds to set door unlocked
Delicate
Sport wash
Silent
Quick
Spin
Self-clean
Power
HW60-B1286
To add clothes during washing or want to remove clothes due to extended power failure,make sure that the water level in the drum is properly below the lower edge of sight glass, the water temperature is below 50 C and the inner drum is not running, then remove the drain pipe from its support and lower it until no water is drained from the drain pipe, replace the drain pipe. Open the filter door at the bottom of the washer, and you will see a pull pole. Take out the pull wire and gently pull it downwards until you hear a low sound, the door will open, now you can add or remove the clothes. Afterwards, reset the pull pole and filter door.
Pull pole
USING THE
APPLIANCE
CARE CHART
Resistant material
Delicate fabric
Washable at 95 °C
Washable at 60 °C
Washable at 40 °C
Washable at 30 °C
Hand wash
Dry clean only
Wool Seal
Bleachable in cold water
Do not bleach
Iron at 200 °C
Iron at 150 °C
Iron at 100 °C
Don't iron
Dry cleaning with any solvent
Dry cleaning with pericloride
Dry cleaning with aviation fuel
Don't dry clean
Dry fl at
Hung to dry
Dry on clothes hanger
Tumble dry, normal heat
Tumble dry, reduced heat
Don't tumble dry
15
LOAD REFERENCE
Bed sheet (single)
Blanket
Blended fabric clothes
Jackets
Jeans
Overalls
Ladies Pyjamas
Shirts
Socks
T-Shirts
Underwear
Cotton
Wool
/
Cotton
/
Cotton
/
/
Blended fabrics
Cotton
Blended fabrics
Approximately 800g
Approximately 3000g
Approximately 800g
Approximately 800g
Approximately 800g
Approximately 950g
Approximately 200g
Approximately 300g
Approximately 50g
Approximately 300g
Approximately 70g
16
CLEANING & CARE
AFTER WASHING
MAINTENANCE
Turn off the water supply and pull out electricity plug after each wash.
Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace the drain hose.
CLEANING THE DETERGENT DRAWER
Clean the detergent distribution drawer regularly.
Swing out the drawer, flush it clean with water and then replace it.
1.
2.
2.
CLEANING THE MACHINE
Unplug the machine during cleaning and maintenance. Use a soft cloth dampened with soap liquid to clean the machine case and rubber components. Do not use organic chemicals or corrosive solvents.
CLEANING THE FILTER
Clean the filter once a month:
1. Open the bottom cover.
2.Remove the filter by turning counterclockwise.
3.Flush the filter clean with running water.
4.Replace the filter by turning clockwise and remount the cover.
1.
2.
Caution:
1.The filter must be in place, or it may lead to leakage.
2.Place a container under the drain pump filter, to collect any excess water that may come out of the drain pump when the filter is removed.
3.
4.
1.
MAINTENANCE
WATER INLET VALVE AND INLET VALVE FILTER
To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve filter regularly.
17
MOVING THE MACHINE
1.
2.
3.
4.
5.
If the machine is to be moved to a distant location, replace the transportation bolts removed before installation to prevent damage as shown below.
Remove the back cover.
Remove the blanking plugs.
Insert the synthetic stabilisers and the transportation bolts.
Tighten the bolts with a spanner.
Replace the back cover.
LONG PERIODS OF DISUSE
If the washing machine is left idle for a long period, pull out the electrical plug and turn off the water supply. Open the washer door to prevent formation of moisture and odours. Let the door open while not used.
Wash
Rinse
Spin
Temp.
Speed
Auto
Strong wash Delay Pre-wash Soak
Heavy
Silk
Wool
Synthetic
Memory
Cotton
Start / Pause
Press and hold 2seconds to set door unlocked
Delicate
Sport wash
Silent
Quick
Spin
Self-clean
Power
HW60-B1286
EuAr
End
1:25
19:30
UNb
18
DISPLAY CODES
MAINTENANCE
DISPLAY CODES AND SPECIAL FUNCTIONS
CODES CAUSES
Err1
Err2
Err3
Err4
Err5
¬ Door is not properly shut.
¬ Drainage error, water not emptied within 6 minutes.
¬ Temperature sensor not properly connected or damaged.
¬ Heater error (Appears at the end of a cycle).
¬Water level not met in 8 minutes.
SOLUTIONS
_ Shut the door properlyˈand then press the Start/Pause button.
_ Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel.
_ Contact the maintenance personnel.
Err7
Err8
¬The height of the drain hose is below 80 cm.
¬ The drain hose is in water.
¬ Motor error.
¬ Water exceeds protective level.
_ Contact the maintenance personnel.
_ M a k e s u r e t h a t t a p si t u r n e d o n , a n d w a t e r p r e s s u r e si n o r m a
If problem still exists, please contact the maintenance personnel.
.l
_ Install drain hose within 80-100 cm of height.
_ Make sure the drain hose is not in water.
_ Contact the maintenance personnel.
_ Contact the maintenance personnel.
Er10 ¬ The signal of Water level sensor is wrong.
_ Contact the maintenance personnel.
¬ The PBC and the motor cant’t communicate.
_ Contact the maintenance personnel.
¬ End of wash cycle.
¬The remaining time is 1 hour 25 minutes.
¬Status information:Preset time for delayed operation.
After the last rinsing cycle finishes,spinning fails completely due to unbalance of the laundry.
¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program.
It can no longer be changed by operating buttons or knobs. To unlock press the "Delay" and "Start/Pause" buttons again for 3 seconds.
¬ Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the present settings will be saved and the preset operation will resume when the power is on again.
¬ To cancel a program
Press the "Start/Pause" button, then switch off the power and the program is automatically cancelled. Turn the program selector again to choose another program.
Note: During the spin process, if too much foam is inspected, in order to protect the motor, the washing machine will eliminate the foam automatically; the motor will stop and the drain pump will drain the water continuously for 90 seconds. If it happens more than
3 times, the motor will stop until the end of cycle without spinning.
MAINTENANCE 19
TROUBLESHOOTING
TROUBLESHOOTING
The following circumstances do not constitute problems. Do not contact the Service Center until the problem has been confi rmed.
PROBLEM
Washing machine fails to operate.
CAUSES
¬ Poor connection to the power supply.
¬ Power failure.
¬ The washer door is not properly closed.
¬ Machine has not been switched on.
Washing machine cannot be fi lled with water.
¬ The "Start/Pause" button is not pressed.
¬ Water tap is not turned on.
¬ Water pressure is less than 0,03 Mpa.
¬ The inlet hose is kinked.
¬ Water supply failure.
¬ The program knob is not properly set.
¬ The washer door is not properly closed.
¬ The inlet hose fi lter is blocked.
Machine is draining while being fi lled.
Drainage failure.
Strong vibration while spinning.
Operation stops before completing wash cycle.
SOLUTIONS
_ Check connection to the power supply.
_ Check the power supply.
_ Close the washer door properly.
_ Make sure the machine is switched on.
_ press the "Start/Pause" button.
_ Turn on the water tap.
_ Check water pressure.
_ Check the inlet hose.
_ Ensure the water supply.
_ Set the program knob properly.
_ Close the washer door properly.
_ Unblock the inlet hose fi lter.
¬ The height of the drain hose is below 80 cm.
¬ The drain hose is in water.
¬ Drain hose is blocked.
¬ Drain hose end is higher than 100 cm above the fl oor level.
¬ The fi lter is blocked.
_ Install drain hose within 80-100 cm of height.
_ Make sure the drain hose is not in water.
_ Unblock the drain hose.
_ Make sure the drain hose end is lower than
100 cm above fl oor level.
_ Unblock the fi lter.
¬ Not all transportation bolts have been removed.
¬ Washing machine is located on an uneven surface or is not level.
¬ Machine load is over Max load.
_ Remove all transportation bolts.
_ Make sure the washing machine is on an even surface and levelled.
_ Reduce amount of laundry in the drum.
¬ Water or electricity failure.
_ Check the power supply.
Operation stops for a period of time.
¬ Washing machine gives an error message.
¬ Washing machine is in soaking cycle?
Excessive foam in the drum, which is spilled to the distribution drawer.
¬ The detergent is not a low-foaming type or for manual wash.
¬ Excessive use of detergent.
_ Check display codes.
_ Press the rinse hood button or the Start/pause
button again to cancel it.
_ Check if your detergent is appropriate.
_ Reduce amount of detergent in the distribution drawer.
Automatic adjustment of the washing time.
¬ The washing program duration will be adjusted _ This is normal and doesn't affect the functionality.
Spinning fails ¬ Unbalance of the laundry _ Add clothes or run a spinning program again.
20 MAINTENANCE
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement