Haier HK1270TVEME Operation Manual

Operation Manual
Automatic Drum Washing Machine
HK1270TVEME
Table of Contents
Before using the appliance
Name of parts...inside front cover
Matters needing attention......1-3
Installation.............................4-5
Function ...............................6-7
How to operate the wasing machine
Program description table........8
Preparation .............................9
Washing Procedure ..........10-11
Maintenance
Maintenance ..........................12
Troubleshooting Guide ..........13
Technical Specifications ........14
Wiring Circuit .........................15
Name of Parts
Detergent dispenser
Top
Program selector
Function selector
ON/OFF button
Door
Handle
Porthole
Bottom plaque
3
Caution and Warning symbols
For you safely,any instructions in this manual with this
"Warning"sign must be followed strictly.
For your safety and to prevent damage to the washing
machine,any instructions in this manual with this "Stop"
sign must be followed strictly.
This diagram may be slightly different from the layout of the washing
machine you have just purchased due to techincal improvements
Matters Needing Attention
Wiring Circuit
8.The washing machine should not be installed 9. The carpet must not obstruct the ventilation
outdoors or in a damp place. In the event of water
openings in the base of the washing machine.
leakage or splashes allow the machine to dry
HK1270TVEME
N
L
naturally.
Power Switch
O1
O2
D1
ST-1
ST-2
ST-3
ST-4
ST-5
ST-6
ST-7
ST-8
ST-9
J12-3
J12-4
J12-11
Door Lock
D2
D3
J12-12
J12-4
Power Drive PCB
M1B1
M
J12-11
J12-5
M2 B2
M3B3
M4B4
M5 B5
M6 B6
Motor
J12-1
J12-2
N1
Display PCB
Thermostat
N2
P1
Drain Pump
P2
VH2
J12-7
J12-8
J12-9
VH1
V1
V2
Electronic Wash Switch
10.Keep away from heat sources and direct sunlight 11.During installation, ensure that the electric
cable is not trapped by the washing machine
to prevent plastic and rubber components from
and avoid damage to the electric cable.
aging.
G
J12-6
L1
L2
J12-10
J12-5
M7 B7
L3
H1
H2
Pressure Switch Heating Element
During Use
1. Before use, check the joints of the filling hose,
2. Keep the door slightly open when the washing
the tap and the drainage hose for possible
problems from water pressure fluctuations.
machine is not in use to prevent formation of
odors; do not cover the washing machine with
plastic cover so that inside dampness cannot
be kept in.
If joints are loose or there is leakage, turn
off the tap and repair. Do not use the washing
machine until the hoses are properly fixed.
15
2
Matters Needing Attention
Technical Specifications
Model
3. Do not place heavy, heating source or wet articles
on the top of the washing machine.
HK1270TVEME
4. Do not hot wash foam rubber or sponge-like
materials.
Power supply
Power(Max)
5. Before washing, do up zippers, buttons and clothes
straps and put small articles, such as socks, laces
or bras, into a washing bag or a pillow.
6. Do
not open the detergent distribution drawer
during the wash cycle..
Steel wires in bras will pop
out during washing; never
wash bras containing steel
wires.
7. The door is fitted with a self-lock device and will not 8. After each wash program, turn off the tap to prevent
leakage; and unplug the washing machine and
open until 2~3 minutes after the washing machine
wipe clean the lower part of the porthole.
stops. Do not force the door open. Do not open the
door if water level can reach the porthole.
230V~/50Hz
2000
Water pressure (MPa)
0.03 < P < 1
Washing power(W)
200
Spinning power(W)
550
Max. wash load (kg)
7
Spinning speed (MAX) (r/min)
1200
Wash program
9
Heating power (W)
1800
Weight (kg)
72
Anti-Electric Shock
I
Anti-Water Class
IPX4
Installation
Troubleshooting
The following circumstances do not constitute problems. Do not contact the maintenance service
until the problem has been confirmed.
Problem
The washing machine fails to operate
Possible cause
Poor connection to power supply
Power failure
Door is not properly closed (It will show E1)
Machine has not been switched on
ƽ
Remove all the packing materials (including the
foam base)to prevent vibration during use, as
shown in Fig.1.Upon opening of the package,
water drops may be seen on the plastic bag and
the porthole. This is normal phenomenon resulting
from water test in the factory.
Fig. 1
ƽ Check attachments and materials with reference to the following
Qty
Washing machine cannot be filled
with water
The machine is draining while is
being filled
Drainage failure
Water tap is not turned on(It will show E5)
Water pressure is less than 0.03Mpa
The inlet hose is kinked
Water supply failure
The program dial is not properly set
The door is not properly closed
The inlet hose filter is blocked
The height of the drainage hose is below 80cm (it
should be within 80-100cm)
The drainage hose end is in water
Drainage hose is blocked (It will show E2)
Drainage hose end is exceed 100cm above the floor
level
The filter is blocked
Strong vibration during spin drying
Not all packing bolts have been removed
Washing machine is located on an uneven surface
Machine load is over 7kg.
Not all foam packing has been removed from the motor
Operation stops before completion
of a wash cycle
Water or electricity failure
Washing machine is in soak cycle
Operation stops for a period of time
Washing machine is in soak cycle
Washing machine gives an error message.
Excessive foam in the drum, which
is spilled to the distribution drawer
The detergent is not a low-foaming type or for manual
wash
Excessive use of detergent
Name
Operation
manual
Quality
certificate
1
1
Water
hose
Drainage
holder
Plastic
plugs
Model
HK1270TVEME
1
1
3
ƽ Dismantle the packing bolts as shown in Fig. 2.
The packing bolts are designed for clamping anti-vibration components
inside of the washing machine during the transportation process.
Before use:
1. Remove the back plate;
2. Remove the three packing bolts on the back plate and take out the
rubber hose;
3. Replace the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: The packing bolts and rubber hose should be kept in a safe
place for later use)
Fig.2
ƽ Adjusting the washing machine
There are adjustable feet under the bottom of the washing machine. Before
use, the washing machine should be adjusted, as shown in Fig. 3, so that it
is level.
Fig.3
13
4
4. Clean the filter Cleaning methods (once a month)
1) Push out the outer cover (Fig. 1);
2) Screw out filter by turning counterclockwise (Fig. 2);
3) Flash clean with running water;
4) Replace the filter by turning clockwise and remount the
cover.
Caution: The filter must be in place, or it may lead to
leakage.
F
Fig1
Fig2
Fig3
The appliance is to be connected to the water mains using new hose-sets
and that old hose-sets should not be reused.
12
5
Hints for Saving Energy
Operational Functions
.
4. Setting washing temperature
Temp.
Speed
Coloured
Synthetic
HK1270 TVEME
Delicate
Normal
Easy lroning Timer Delay Prewash Extra Rinse
Super Wash
Load Select
ON/OFF
Intensive
Wool
Press the temperature button until "_ _ oC" is displayed if heating is not needed; otherwise, select
an appropriate temperature as required (refer to the "Guide to Operational Program Selection").
Start
Rinse
Quick
Spin
DIGITAL 7KG
/
$Ironing-free button
Press this button, the laundry will be fluffed up at the end of the spinning cycle to
reduce wrinkles.
B:Delay button
Press the Delay button before the program is started if necessary. Press of the Delay button
one time, the delay time will increase one hour (the regulating range is from the current setting
to 24 hours). After the delay time is changed, press the Start button to activate the delay
function.
Note: The delay time must be longer than the program time; otherwise, the washing machine
will start the wash program directly.
5. Function selecting button
Select functions as required (refer to the "Operational Functions" section).
6. Washing
Press the Start / Pause button, the indicator at the upper left corner of the button will blink
and the washing machine starts operation.
7. Finish
The washing machine will stop operation automatically when a wash cycle ends. The "End" sign will
appear. Open the door and take out the laundry. Then turn off the tap and unplug the power cable.
C:Pre-wash button
Press this button, the washing machine will automatically start a prewash cycle during
execution of a washing program.
D: Extra rinsing button
Press this button, the washing machine will run an additional rinsing cycle to further clean your
clothes.
E: Super wash button
Press this button,the display will be on when choosing super wash button. The "
"
and "
" will display circularly. The sign of super wash will be off when the super wash
system finished.
F: Washing load button
Press this button, 3 load levels of "ϔϔϔϔ" (0-2kg), "ѠѠѠѠ" (2-4kg) and "ϝϝϝϝ"
(4-6kg) will appear on the screen for manual selection before water is filled. After the load is
set, the water content will be automatically adjusted.
G: Power button
ƽ Hints for saving energy
During operation
1. Collect clothes for one full wash load.
2. Do not overload the washing machine.
3. Pre-wash heavily soiled clothes.
4. Reduce the amount of detergent or choose standard or delicate wash
programs for slightly soiled clothes.
5. Choose a proper washing temperature. Only exceed 60ć for heavily
soiled clothes.
6. Do not use more detergent than required.
7. Softening agent makes clothes feel softer and easier to iron.
Press this button to switch on the washing machine; press it again to switch the machine off.
To cancle a wash program during a wash cycle,please switch the machine off.
Functions
Washing Procedure
1. Loading
Open the door, put in the laundry piece by piece.
Close the door tightly.
Notes: 1) When first using the washing
machine,let it run unloaded for one program
to prevent the laundry from being tainted by
oil or dirty water from the washing machine.
2) Do not overload the washing
machine.
H: Wash programming knob and start button
By turning the knob clockwise or counterclockwise, the required program can be selected;
press the start button to start a program; press it again to pause
Load Reference
ƽ-HDQV
J
ƽOveralls
(cotton appr 950g)
ƽ Pajamas
(appr 200g)
ƽ Blended fabric
clothes
(appr 800g)
ƽ Shirts
(appr 300g)
ƽ T-shirt
(cotton
appr 300g)
ƽ Jackets (cotton
appr 800g)
ƽ
Underwear
(blended fabrics appr 70g)
ƽ Socks (blended
fabrics appr 50g)
ƽ Single bed sheets
(cotton appr 800g)
ƽ Woolen
blankets
(appr 3000)
2. Adding detergent
Slide out the detergent drawer and put the required detergent and
softening agent into the corresponding boxes. Push back the drawer gently.
Caution:
1) For pre-washing program, detergent should be added to both
compartments 1 and 2. Compartment 2 allows only solid detergents.
For other programs, do not add detergent to compartment 1.
2) Do not overuse softener; otherwise, it will damage the artificial
fibers. Refer to the instructions during use.
3. Selecting washing program
To get the best washing effect, an appropriate washing program should be selected
according to the laundry type.
Note: The above operations refer to conditions without power-off memory. Or the washing
machine will continue operation from where the program was broken. To clear memory,
press the Start/Pause button. Turn off the power for a few seconds and turn on again, all
the settings will be renewed.
I: Speed button
Press this button to set a required spinning speed, which covers 0 rpm to 1200 rpm.
J : Temperature button
Press this button to set a required temperature. The selectable temperature range is
0-90Ɔ. (Some programs have temperature limits. Refer to the programming guide)
K: Display
Remaining time, set temperature, spinning speed, other function information, and error messages
are displayed. Refer to the Display Description
/Detergent distribution drawer
There are instructions on the handle of the distribution drawer. Swing
out the drawer, three compartments can be seen.
Compartment
1: Pre-washing detergent. If pre-wash is not selected, do
not add detergent.
Compartment 2: Detergent for all washing programs. Detergent must be
added whether pre-wash is selected or not.
Compartment 3: Softening agent, conditioning agent, perfume, etc
B+C: combination for keyboard lock
After a program is started, press the delay tbutton and the Prewash button at the same
time for 3 seconds, the keyboard will be locked and "SAFE ON" will appear on the screen.
Press the two buttons again for 3 seconds, the keyboard will be unlocked and "SAFE OFF"
will be displayed. This function is used to protect the washing machine from being disturbed
during operation, such as accidental press of buttons or turning of knobs by children, as this
may affect or suspend the operation of a program. Note: If this function is activated during
a washing cycle, be sure to inactivate it at the end of the cycle when the "End" sign is
displayed.
Caution: If the keyboard lock is not activated, press the Start/Pause button and then cut off
the power, the suspended program will be canceled after power is resumed. Now turn the
program knob to reselect.
Program Description Table
Preparation
Detergent
Mode Selection
Button Position
Cotton
Synthetic
Delicate
/Super
Quick
Wash
Single
Wash
Program
Note :"
Program Time
Recommended Selectable
(At Max
Laundry
Temperature
Temperature)
Program
1
Intense
Heavy and
thick fabrics
0-90ć
2:26
ƾ
Normal
White fabrics
0-90ć
1:41
ƾ
Coloured
Fast-color and
medium soil
fabrics
0-60
1:25
ƾ
Synthetic
Fast-color
and heavysoil fabrics
Delicate
Wool and silk
0-60
0:58
0-40ć
0:49
ƾ
Turn on the tap ensure that the water in clear.
Caution:Before staring the washing machine turn on the water
faucet to ensure the water faucet and the water inlet hose are
connected correctly and do not leak
Wool
0-40ć
0:46
ƾ
Quick/29min
Medium-soil
cotton &
synthetics
0-40ć
0:29
ƾ
Rinse
0:32
Spin
0:11
" indicates that softener or bleacher can be added if needed;
3.Laundry treatment
Sort out clothes according to type and extent of dirt.There are
three types of clothes:cotton,synthetical and woolen (silk) fabrics.
Only special low foam detergent should
be used in automatic drum washing
mashine,form blended or wool fabrics
special deter-gent should ne used.dry
clearning solvent should not be used
such as trichhloroethy-lene or alike
(caution :load the required amount of
detergent only).
Separate white clothes from colored.If whites and coloreds
are combimed for one load,make sure the coloreds are colorfast
ƾ
Wool
" X " indicates that detergent must not be added.
3
2.Water supply
Plug in the power supply 230V~ 50HZ
4.Detergent selection
" ƾ " indicates that detergent must be added;
"
2
1.Power supply
-Clothing with frayed edges or yams should be put in a wash
bag or special bag before washing
-repair damged clothing,lose buttons or damaged zips
and hooks before washing.
-Bed sheets and table ware should be loosely loaded and not
folded.
This washing mashine is for househould use and designed
for mechanically washable clothes.When washing,separate
unwashable clothes with reference to clothes labels.
5.Wash Load
Type
Max Load
non-fade cottens
7kg
Delicate fabrics
4kg
Woolen fabrics
2kg
" indicates that if pre-wash is selected,detergent must be added.