Harbor Freight Tools 13 in. Electric String Trimmer Product manual

Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
REV 14f
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2014 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety
Safetye��������������������������������������������������������� 2
Maintenancei���������������������������������������������� 12
Specifications.............................................. 5
Setup........................................................... 6
Operationa���������������������������������������������������� 9
Parts List and Diagram............................... 14
Warranty..................................................... 16
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Setup
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Operation
IMPORTANT SAFETY INSTRUCTIONS
When using electric gardening appliances, basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
Power Cord Safety
Maintenance
WARNING! - To reduce the risk of electric
shock, use only with an extension cord
intended for outdoor use, such as an
extension cord of cord type
SW-A, SOW-A, STW-A, STOW-A, SJW-A,
SJOW-A, SJTW-A, or SJTOW-A.
Page 2
1. Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to
be used for the gardening appliance. Receptacles
are available having built-in GFCI protection
and may be used for this measure of safety.
2. Do not Abuse Cord - Do not carry appliance by
cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
For technical questions, please call 1-888-866-5797.
Item 62338
The following table shows the correct
cord size to use depending on cord length
and nameplate ampere rating. If in doubt,
use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
TABLE A – MINIMUM WIRE GAUGE FOR
EXTENSION CORDS (120 VOLT)
Ampere Rating
4. WARNING: The cord of this product contains
lead, a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
EXTENSION CORD LENGTH
(at full load)
25′
50′
100′
150′
0–6
18
16
16
14
6 – 10
18
16
14
12
10 – 12
16
16
14
12
12 – 16
14
12
Safety
Extension Cord Size
3. To reduce the risk of electric shock, this appliance
has a polarized plug (one blade is wider than
the other) and will require the use of a polarized
extension cord. The appliance plug will fit
into a polarized extension cord only one way.
If the plug does not fit fully into the extension cord,
reverse the plug. If the plug still does not fit, obtain
a correct polarized extension cord. A polarized
extension cord will require the use of a polarized
wall outlet. This plug will fit into the polarized wall
outlet only one way. If the plug does not fit fully
into the wall outlet, reverse the plug. If the plug
still does not fit, contact a qualified electrician to
install the proper wall outlet. Do not change the
equipment plug, extension cord receptacle, or
extension cord plug in any way. This design is
referred to as double-insulated, indicated by
.
Not recommended
To reduce the risk of the cords
pulling apart during operation:
a. Make a loop in the
extension cord, and
press that cord loop through
the hole in the handle.
5. Extension Cord - Make sure your extension cord
is in good condition. When using an extension
cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized
extension cord will cause a drop in line voltage
resulting in loss of power and overheating.
c
b
Setup
Connecting Cords
a
b. Hook that cord loop
around the cord hook.
c. Make sure the Trigger is released,
then plug the cord ends together.
2.
Wear ANSI-approved safety goggles and
heavy-duty work gloves. Use face or
dust mask if operation is dusty.
3. Avoid Unintentional Starting - Do not carry
plugged-in appliance with finger on switch.
Be sure switch is off when plugging in.
4. Do not Overreach Keep proper footing and balance at all times.
5. Stay Alert - Watch what you are doing. Use common
sense. Do not operate appliance when you are tired.
Item 62338
6.
Wear thick jeans and steel-toed
work boots to help prevent injury
caused by flying debris.
7. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Don’t use with power switch locked on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly grounded.
Ground Fault Circuit Interrupter (GFCI)
should also be implemented –
it prevents sustained electrical shock.
For technical questions, please call 1-888-866-5797.
Page 3
Maintenance
1. Dress Properly - Do not wear loose clothing or
jewelry. They can be caught in moving parts.
Use of rubber gloves and substantial footwear
is recommended when working outdoors.
Wear protective hair covering to contain long hair.
Operation
Personal Safety
Gardening Appliance Use and Care
1. Avoid Dangerous Environment Do not use appliances in damp or wet locations.
2. Do not Use In Rain.
Safety
3. Keep Children Away - All visitors should
be kept at a distance from work area.
4. When servicing use only identical replacement parts.
5. Use Right Appliance - Do not use appliance for
any job except that for which it is intended.
6. Do not Force Appliance - It will do the job
better and with less likelihood of injury at
the rate for which it was designed.
7. Store Idle Appliances Indoors - When not in use,
appliances should be stored indoors in dry, and
high or locked-up place - out of reach of children.
Setup
8. Maintain Appliance With Care - Keep cutting edge
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating
and changing accessories. Inspect appliance cord
periodically, and if damaged, have it repaired by
an authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean, and free from oil and grease.
9. Check Damaged Parts - Before further use of the
appliance, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by a qualified technician
unless indicated elsewhere in this manual.
10. Disconnect Appliance - Disconnect the appliance
from the power supply when not in use,
before servicing, when changing
accessories such as blades, and the like.
11. Keep guards in place and in working order.
12. Only replace the line on this appliance with
the line material and diameter of line listed
on the Specifications table. Other materials,
such as wire, rope, or blades can damage the
appliance and be forcefully and dangerously
ejected from the appliance upon breaking.
Vibration Hazard
Operation
This appliance vibrates during use.
Repeated or long‑term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
Maintenance
1. Anyone using vibrating appliances regularly or
for an extended period should first be examined
by a doctor and then have regular medical
check-ups to ensure medical problems are not
being caused or worsened from use. Pregnant
women or people who have impaired blood
circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or Raynaud’s
Disease should not use this appliance. If you
feel any symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
Page 4
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use appliances with the lowest vibration when
there is a choice between different processes.
5. Include vibration-free periods each day of work.
6. Grip appliance as lightly as possible
(while still keeping safe control of it).
Let the appliance do the work.
7. To reduce vibration, maintain the appliance
as explained in this manual. If any abnormal
vibration occurs, stop use immediately.
For technical questions, please call 1-888-866-5797.
Item 62338
General Safety
2. Do not use in rain, snow, sprinklers, or wet grass.
Do not rinse off the Trimmer.
6. Do not use appliance for other than intended use.
7. Maintain labels and nameplates on the appliance.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
8. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
3. Use only during daylight hours.
4. Carefully inspect the wire spool and guard
before plugging in the Trimmer. Do not
use Trimmer if any part is cracked or damaged.
5. Cover the Trimming Blade after every use.
Safety
1. The spool will continue to rotate for a few seconds
after use. Allow it to stop completely and unplug
it before putting the appliance down, making
any adjustments, or servicing the appliance.
Setup
SAVE THESE INSTRUCTIONS.
Electrical Rating
120VAC / 60Hz / 4A
No Load Speed
9,000 RPM
Replacement Line Type
0.065" Nylon
Operation
Specifications
Maintenance
3098095
Item 62338
For technical questions, please call 1-888-866-5797.
Page 5
Set Up Instructions
Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
Safety
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch/Trigger is in the off‑position and unplug the appliance
from its electrical outlet before performing any procedure in this section.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Assembly
Install Guard
Setup
1. CAUTION! TO PREVENT ACCIDENTAL CUTS:
Cover the Trimming Blade (39) with the
Blade Cover (40) before installing the Guard.
Housing
2. Align Guard (42) over Housing as shown in Figure A.
WARNING! TO PREVENT SERIOUS INJURY FROM
FLYING DEBRIS AND PIECES OF TRIMMING LINE:
Install the guard only in the orientation shown.
Screw (25)
Guard (42)
3. Attach Guard to Housing using 4 Screws (25).
Blade
Cover (40)
Figure A: Installing Guard
Install Auxiliary Handle
Operation
1. Position Auxiliary Handle over Handle Bracket (14).
2. Install Locking Knob (15) and tighten
it in place to secure the Handle.
3. Loosen the Locking Knob and move the
Auxiliary Handle to the desired position.
WARNING! Tighten the Locking Knob
after adjustment.
Locking
Knob (15)
Maintenance
Handle
Bracket (14)
Auxiliary
Handle
Figure B: Auxiliary Handle Installation
Page 6
For technical questions, please call 1-888-866-5797.
Item 62338
Install Edge Guide
1. Snap Edge Guide (21) into holes on both
sides of Housing as shown in Figure C.
2. Use the Edge Guide to limit striking objects
with the Line while trimming nearby.
Edge
Guide (21)
3. Flip the Edge Guide up out of
the way when not in use.
Maintenance
Operation
Setup
Figure C: Install Edge Guide
Safety
Housing
Item 62338
For technical questions, please call 1-888-866-5797.
Page 7
Functions
Trigger
Safety
Auxiliary Handle
Cord Hook
Angle
Sleeve
Length
Sleeve
Setup
Head Angle
Button
Blade Cover
Guard
Operation
Edge Guide
Line Reel
Available Accessories/Attachments
Use of any accessory or attachment other than those listed below may increase the risk of serious injury.
Only replace the line on this appliance with the line material and diameter of line listed on
the Specifications table. Other materials, such as wire, rope, or blades can damage the
appliance and be forcefully and dangerously ejected from the appliance upon breaking.
Accessories and attachments are not available for this product.
Maintenance
Page 8
For technical questions, please call 1-888-866-5797.
Item 62338
Operating Instructions
TO PREVENT SERIOUS INJURY:
Before operating the gardening appliance, put on ANSI-approved safety goggles, close-toed work boots,
long pants, and other safety gear. Safety goggles and other safety gear are sold separately.
Safety
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch/Trigger is in the off‑position and unplug the
appliance from its electrical outlet before setting up the appliance.
1. An extension cord (sold separately) will be
required. Ensure that the extension cord is an
outdoor type extension cord and that it is the
correct design to accept this appliance’s plug.
2.
WARNING!
TO PREVENT ELECTRIC SHOCK AND
SERIOUS PERSONAL INJURY:
The extension cord must remain
secured to the appliance’s plug.
3. Secure the extension cord
using the cord hook
as explained below.
a. Make a loop in the
extension cord, and
press that cord loop through
the hole in the handle.
c
b
a
Setup
Using Cord Hook
b. Hook that cord loop
around the cord hook.
Maintenance
Operation
c. Make sure the Trigger is released,
then plug the cord ends together.
Item 62338
For technical questions, please call 1-888-866-5797.
Page 9
Replacing Nylon Line
1. Press in buttons on side of Reel (33) and
remove Reel Cover (38) and Spool (36).
5. Wind onto top groove using slight
tension and following arrow direction.
Press Line into clip on top of Spool.
Safety
Reel (33)
Spool (36)
Reel
Cover (38)
button
Figure D: Reel Assembly
2. Remove all old Line from Spool.
3. Cut two equal lengths of 0.065″ Nylon Line.
4. Insert one Line into hole in top groove of Spool.
Figure F: Wind Line
6. Repeat to wind other Line onto bottom groove.
Press Line into clip on other side of Spool.
Setup
7. Insert Spool partway into Reel, insert Line
ends through round holes in side of Reel,
unclip Lines, and pull Line ends snug.
8. Reassemble Reel Cover onto Reel and make sure
that both buttons pop back into place.
Figure E: Insert Line
Feeding Nylon Line
Operation
NOTICE: To prevent damage, DO NOT BUMP REEL.
This string trimmer feeds Line
automatically when stopping.
1. Make sure area is safe
to operate appliance in,
then operate it at
full speed.
2. Release Trigger and allow Line to stop fully.
3. Line will feed slightly. Repeat as desired.
Note: Line will feed only if Spool is wound
correctly and can unwrap freely.
4. To manually feed Line, unplug the Power Cord,
press the Feed Button (34) at the base
of the Reel, and pull out the Line slightly.
Keep pushing the Button and pulling the Line
out until the Line reaches the desired length.
Adjusting Working Height
1. Loosen the Length Sleeve.
2. Adjust the Tube to the desired Length.
Maintenance
3. Tighten the Length Sleeve.
Angle
Sleeve
Length
Sleeve
Figure G: Tube Adjusting Sleeves
Page 10
For technical questions, please call 1-888-866-5797.
Item 62338
1. If head is in vertical position, pull back
on Angle Sleeve, rotate head 180°,
and release Angle Sleeve.
CAUTION! Make sure Angle Sleeve
locks in the new position.
4. Remove the Blade Cover and keep it available.
2. To adjust head angle, press the
Head Angle Button (27), adjust as desired, and
release Button. CAUTION! Make sure head angle
locks in the new position.
6. Squeeze the Trigger, and slowly move the
spinning Line across the work area.
CAUTION! DO NOT STRIKE THE HEAD,
doing so may damage it and cause it to break.
Setup
7. To prevent accidents, turn off the appliance
and unplug it after use. Clean, then cover the
Trimming Blade with the Blade Cover and store
the appliance indoors out of children’s reach.
Edger Operation
1. If head is in horizontal position, pull
back on Angle Sleeve, rotate head 180°,
and release Angle Sleeve.
CAUTION! Make sure Angle Sleeve
locks in the new position.
2. To adjust head angle, press the
Head Angle Button (27), adjust as desired, and
release Button. CAUTION! Make sure head angle
locks in the new position.
3. Clear the work area of all fragile objects and all
objects that may be thrown during operation.
Keep extension cord clear of work area.
5. Make sure Trigger is released, then connect
the Power Cord to the extension cord,
see Using Cord Hook on page 9.
6. Squeeze the Trigger, and slowly move the
spinning Line across the work area.
CAUTION! DO NOT STRIKE THE HEAD,
doing so may damage it and cause it to break.
7. To prevent accidents, turn off the appliance
and unplug it after use. Clean, then cover the
Trimming Blade with the Blade Cover and store
the appliance indoors out of children’s reach.
Maintenance
4. Remove the Blade Cover and keep it available.
Operation
3. Clear the work area of all fragile objects and all
objects that may be thrown during operation.
Keep extension cord clear of work area.
5. Make sure Trigger is released, then connect
the Power Cord to the extension cord,
see Using Cord Hook on page 9.
Safety
Trimmer Operation
Item 62338
For technical questions, please call 1-888-866-5797.
Page 11
Maintenance and Servicing
Procedures not specifically explained in this manual
must be performed only by a qualified technician.
Safety
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch/Trigger is in the off‑position and unplug the appliance
from its electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM APPLIANCE FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs,
have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the appliance. Check for:
Setup
• loose hardware,
• misalignment or binding of moving parts,
• damaged cord/electrical wiring,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. AFTER USE, clean external surfaces of
the appliance with clean, moist cloth.
3. To feed/replace trimming Line,
see instructions on page 10.
4.
WARNING! If the supply cord of this
appliance is damaged, it must be replaced
only by a qualified service technician.
Operation
Maintenance
Page 12
For technical questions, please call 1-888-866-5797.
Item 62338
Maintenance
Operation
Setup
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Safety
PLEASE READ THE FOLLOWING CAREFULLY
Item 62338
For technical questions, please call 1-888-866-5797.
Page 13
Parts List and Diagram
Parts List
Safety
Part
Setup
Operation
Maintenance
1
2
3
4
5
6
7
8
9
10
10.1
11
12
13
14
15
16
17.4
17.3
17.2
17.1
18
19
20
21
22
23
24
25
26
26.1
27
28
29
30
31
Description
Power Cord
Cord Protector
Socket 2.8X0.8
Cable Clamp Plate
Screw St2.9x14-F-H
Right Handle
Left Handle
Telescopic Aluminum Tube Asm.
Switch
Trigger
Spring
Upper Auxiliary Handle
Lower Auxiliary Handle
Nut M6 (8.8 Grade)
Handle Bracket
Locking Knob
Spring
Tooth Buckle 0.75
Heat Shrinkable Tube Ø3x20
Heat Shrinkable Tube Ø4x20
Heat Shrinkable Tube Ø5x20
Label
Right Housing Cover
Right Housing
Edge Guide
Screw St2.9x12-F-H
Terminal Block
Right Connector
Screw St3.9x14-F-H
Rotation Gear
Shaving Base Spring
Head Angle Button
Left Connector
Left Housing
Left Housing Cover
Label
Qty
1
1
4
1
3
1
1
1
1
1
1
1
1
1
1
1
1
4
4
2
2
1
1
1
1
2
1
1
32
1
1
1
1
1
1
1
Part
32
33
33.1
33.2
34
34.1
35
36
37
37.1
37.2
38
39
40
41
42
43
44
44.1
44.2
44.2.1
44.2.2
44.2.3
44.2.4
44.2.5
44.3
44.4
44.4.1
44.5
44.6
44.7
44.8
44.9
44.10
44.11
Description
Rubber Pad
Reel
Insert A
Rivet Ø5x6
Feed Button
Insert C
Spring
Spool
Cover
Nut M6
Nylon Line Ø0.065"
Reel Cover
Trimming Blade
Blade Cover
Screw St3.9x16
Guard
Warning Label
Motor Assembly
Motor Upper Bracket
Carbon Brush Assembly
Brush Cap
Spring
Carbon Brush Wire
Carbon Brush
Carbon Brush Sleeve
Rotor
Stator
2.8X0.8 Terminal
Bearing 608-2Z
Lower Motor Bracket
Bolt M4x82
Spring Washer 4
Washer 4
Nut M4
Strap
Qty
2
1
4
2
1
4
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
2
2
1
2
2
2
1
2
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14
For technical questions, please call 1-888-866-5797.
Item 62338
Assembly Diagram
2
4
3
5
17.3
Safety
1
9
10.1
12
8
44.10
44.11
44.2.1
44.2.2
44.2.3
14
44.5
44.3
44.2.5
44.9
13
44.4
44.4.1
3
17.4
44.2.4
44.2
15
44
44.1
44.8
44.7
Setup
7
6
11
10
44.5
17.1 17.2
17.1 17.2
44.6
16
28
17.4
29
17.4
30
27
26.1
31
25
33.1
5
34
35
34.1
23
32
36
26
20
37
37.1
21
19
18
Operation
24
33
33.2
37.2
38
22
43
Maintenance
42
40
41
Item 62338
39
For technical questions, please call 1-888-866-5797.
Page 15
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797