Specifications

Materials Molded Polyethylene Plastic

Bin Interior Dimensions 5" D x 3.5" W

Weight Capacity 5 lb per Bin, 75 lb total for rack

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1. Assemble only according to these instructions.

Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.

3. Keep assembly area clean and well lit.

Use Precautions

4. Keep bystanders out of the area during assembly.

5. Do not assemble when tired or when under the influence of alcohol, drugs or medication.

6. Weight capacity and other product capabilities apply to properly and completely assembled product only.

1. This product is not a toy. Do not allow children to play with or near this item.

2. Use as intended only.

3. Inspect before every use; do not use if parts are loose or damaged.

4. Do not exceed listed weight capacity, loaded from bottom up.

Be aware of dynamic loading!

Sudden load movement may briefly create excess load causing product failure.

5. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.

1. Attach the right and left Stands (2) to the

Rack (1), using Bolts (7), Washers (6) and Nuts (8). See Figure A.

4. Do not overload the individual Bins, especially those in the top row. This could cause the Bin Rack to tip over.

5. After assembly, label each Bin via the Name

Plate Holder (3). (For example: Nut M5,

Washer 5mm, Bolt M5x10, Nails, etc.)

Stand (2)

Rack (1)

Bolt (7), Washer

(6), Nut (8)

Plug (5)

Figure A

2. Tap the Plugs (5) into each end of both Stands (2). See Figure A.

a. Slip the Name Plate Holder off the front of the Bin.

b. Place a label between the Name

Plate Holder’s plastic sleeve. c. Snap the Name Plate Holder back in place. See Figure C.

3. Click the colored Bins (4-1, 4-2 and 4-3) into place over the hooks on the Rack (1). See Figure B.

Name Plate

Holder (3)

Red Bin

(4-1)

Blue Bin

(4-3)

Yellow

Bin (4-2)

Figure B

Rack (1)

Figure C

Page 2 For technical questions, please call 1-888-866-5797.

Item 93198

Maintenance

Procedures not specifically explained in this manual must be performed only by a qualified technician.

1. To remove dust, use a damp cloth. To remove grease or oil, use a detergent based cleaning solvent, rinse and dry with a cloth.

2. This product should be stored in a dry area.

Parts List and Diagram

Part Description

1 Rack

2 Stand

3 Name Plate Holder

4-1 Red Bin

4-2 Yellow Bin

Qty

1

2

15

5

5

Part Description

4-3 Blue Bin

5 Plug

6 Washer 5mm

7 Bolt M5X10

8 Nut M5

Qty

8

4

5

4

4

3

3

4-1

3

4-1

3

4-1

3

4-1

3

4-1

3

4-2

3

4-2

3

4-2

3

1 3

4-2

4-2 3

4-3

3

4-3

3

4-3

6

8

6

8

5

2

8

8

6

6

5

6 7

6

7

2

4-3

3

4-3

6

5

6

7

7

Record Serial Number Here:

5

Note: If product has no serial number, record month and year of purchase instead.

Item 93198

Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

For technical questions, please call 1-888-866-5797.

Page 3

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797