Harbor Freight Tools 212cc User's Manual

Table of Contents
SAFETY
Specifications ............................................. 2
Safety ......................................................... 3
Setup .......................................................... 6
Operation .................................................... 8
Maintenance .............................................. 12
Troubleshooting ......................................... 16
Warranties ................................................. 18
Parts Lists and Diagrams .......................... 20
Specifications
Displacement
212cc
Horizontal Single Cylinder
4 stroke OHV
69727: Meets EPA phase III and
CARB emissions standards
Engine Type
SETUP
Cooling System
Type
Capacity
Fuel
Engine Oil
Type SAE
OPERATION
Capacity
Run Time @ 50% Load
with full tank
Sound Level at 22 feet
Bore x Stroke
Compression Ratio
Rotation viewed from PTO
(power takeoff - the output shaft)
Shaft
Spark Plug
Valve Clearance
Speed
69730: Meets EPA phase III
emissions standards
Forced air cooled
87+ octane unleaded gasoline
0.9 Gallon (3.6 Liter)
10W-30 above 32° F
5W-30 at 32° F or below
0.5 Quart
3 hr.
104 dB
70 mm x 55 mm
8.5:1
Counterclockwise
Shaft
3/4″ x 2.43″
Keyway
3/16″ (4.76 mm)
End Tapped
5/16″ - 24 UNF
Type
NGK® BP-6ES
NHSP® / Torch® F6TC
Gap
Intake
Exhaust
Idle
0.7 - 0.8 mm
0.10 - 0.15 mm
0.15 - 0.20 mm
1,800 ±50 RPM
MAINTENANCE
Page 2
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
SAFETY
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
RPM
HP
Property or Statement
Revolutions Per Minute
Horsepower
WARNING marking concerning
Risk of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before set-up and/or use.
WARNING marking concerning
Risk of Hearing Loss.
Wear hearing protection.
Symbol
Property or Statement
WARNING marking concerning
Risk of Respiratory Injury.
Operate engine OUTSIDE and far away
from windows, doors, and vents.
WARNING marking concerning
Risk of Fire while handling fuel.
Do not smoke while handling fuel.
WARNING marking concerning
Risk of Fire.
Do not refuel while operating.
Keep flammable objects away from engine.
OPERATION
Symbol
SETUP
Symbol Definitions
Safety Warnings
WARNING! Read all instructions.
Failure to follow all instructions listed below may result in fire, serious injury and/or DEATH.
The warnings and precautions discussed in this manual cannot cover all possible conditions and
situations that may occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the operator.
MAINTENANCE
SAVE THESE INSTRUCTIONS
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 3
Set up Precautions
SAFETY
1. Gasoline fuel and fumes are flammable, and
potentially explosive. Use proper fuel storage
and handling procedures. Do not store fuel
or other flammable materials nearby.
4. Set up and use only on a flat, level,
well-ventilated surface.
2. Have multiple ABC class fire extinguishers nearby.
6. Use only lubricants and fuel recommended
in the Specifications chart of this manual.
3. Operation of this equipment may create sparks
that can start fires around dry vegetation. A spark
arrestor may be required. The operator should
contact local fire agencies for laws or regulations
relating to fire prevention requirements.
5. Wear ANSI-approved safety goggles, heavy-duty
work gloves, and dust mask/respirator during set up.
Operating Precautions
CARBON MONOXIDE HAZARD
Using an engine indoors CAN KILL
YOU IN MINUTES.
Engine exhaust contains
carbon monoxide. This is a poison
you cannot see or smell.
1.
10. Do not leave the equipment unattended when it is
running. Turn off the equipment (and remove safety
keys, if available) before leaving the work area.
SETUP
11. Engine can produce high noise levels.
Prolonged exposure to noise levels
above 85 dBA is hazardous to hearing.
Always wear ear protection when operating or
working around the gas engine while it is operating.
12. Wear ANSI-approved safety glasses,
hearing protection, and NIOSH-approved
dust mask/respirator under a full face shield
along with steel-toed work boots during use.
NEVER use inside a home or garage,
EVEN IF doors and windows are open.
OPERATION
Only use OUTSIDE and far away from windows,
doors, and vents.
2. Keep children away from the equipment,
especially while it is operating.
3. Keep all spectators at least six feet
from the Engine during operation.
4. Fire Hazard! Do not fill gas tank while engine is
running. Do not operate if gasoline has been spilled.
Clean spilled gasoline before starting engine.
Do not operate near pilot light or open flame.
MAINTENANCE
5. Do not touch engine during use.
Let engine cool down after use.
6. Never store fuel or other flammable
materials near the engine.
7. Only use a suitable means of transport and
lifting devices with sufficient weight bearing
capacity when transporting the Engine.
8. Secure the Engine on transport vehicles to
prevent the tool from rolling, slipping, and tilting.
9. Industrial applications must follow
OSHA requirements.
Page 4
13. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to a heart pacemaker could cause
pacemaker interference or pacemaker failure.
Caution is necessary when near the
engine’s magneto or recoil starter.
14. Use only accessories that are recommended
by Harbor Freight Tools for your model.
Accessories that may be suitable for one
piece of equipment may become hazardous
when used on another piece of equipment.
15. Do not operate in explosive atmospheres,
such as in the presence of flammable
liquids, gases, or dust. Gasoline-powered
engines may ignite the dust or fumes.
16. Stay alert, watch what you are doing and
use common sense when operating this
piece of equipment. Do not use this piece of
equipment while tired or under the influence
of drugs, alcohol or medication.
17. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the equipment in unexpected situations.
18. Use this equipment with both hands
only. Using equipment with only one hand
can easily result in loss of control.
19. Dress properly. Do not wear loose clothing or
jewelry. Keep hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
21. Do not cover the engine or
equipment during operation.
22. Keep the equipment, engine, and
surrounding area clean at all times.
23. Use the equipment, accessories, etc., in accordance
with these instructions and in the manner intended for
the particular type of equipment, taking into account
the working conditions and the work to be performed.
Use of the equipment for operations different from
those intended could result in a hazardous situation.
24. Do not operate the equipment with known
leaks in the engine’s fuel system.
25. This product contains or, when used, produces a
chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
(California Health & Safety Code § 25249.5, et seq.)
26. When spills of fuel or oil occur, they must be
cleaned up immediately. Dispose of fluids and
cleaning materials as per any local, state, or
federal codes and regulations. Store oil rags in
a bottom-ventilated, covered, metal container.
27. Keep hands and feet away from moving parts. Do
not reach over or across equipment while operating.
28. Before use, check for misalignment or binding of
moving parts, breakage of parts, and any other
condition that may affect the equipment’s operation.
If damaged, have the equipment serviced
before using. Many accidents are caused
by poorly maintained equipment.
29. Use the correct equipment for the application.
Do not modify the equipment and do not use the
equipment for a purpose for which it is not intended.
SETUP
20. Parts, especially exhaust system components,
get very hot during use. Stay clear of hot parts.
Service Precautions
a. Turn the engine switch to its “OFF” position.
b. Allow the engine to completely cool.
c. Then, remove the spark plug
cap from the spark plug.
2. Keep all safety guards in place and in
proper working order. Safety guards include
muffler, air cleaner, mechanical guards,
and heat shields, among other guards.
3. Do not alter or adjust any part of the
equipment or its engine that is sealed by the
manufacturer or distributor. Only a qualified
service technician may adjust parts that may
increase or decrease governed engine speed.
8. Follow scheduled engine and
equipment maintenance.
Refueling:
1. Do not smoke, or allow sparks, flames,
or other sources of ignition around the
equipment, especially when refuelling.
2. Do not refill the fuel tank while the
engine is running or hot.
OPERATION
1. Before service, maintenance, or cleaning:
3. TO PREVENT FUEL LEAKAGE AND
FIRE HAZARD, do not fill fuel above
the bottom of fuel strainer.
4. Wear ANSI-approved safety goggles, heavy-duty
work gloves, and dust mask/respirator during service.
6. Have the equipment serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the equipment
is maintained. Do not attempt any service or
maintenance procedures not explained in this
manual or any procedures that you are uncertain
about your ability to perform safely or correctly.
7. Store equipment out of the reach of children.
Max Fuel
DO NOT OVERFILL!
4. Do not fill fuel tank to the top. Leave a little
room for the fuel to expand as needed.
MAINTENANCE
5. Maintain labels and nameplates on the equipment.
These carry important information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
5. Refuel in a well-ventilated area only.
6. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
SAVE THESE INSTRUCTIONS.
ITEM 69727 / 69730
SAFETY
Operating Precautions (cont.)
For technical questions, please call 1-800-520-0882.
Page 5
Set Up
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
SAFETY
TO PREVENT SERIOUS INJURY:
Operate only with proper spark arrestor installed.
Operation of this equipment may create sparks that
can start fires around dry vegetation.
A spark arrestor may be required.
The operator should contact local fire
agencies for laws or regulations relating
to fire prevention requirements.
For item 69727: The emission control system
for this Engine is warranted for standards set
by the U.S. Environmental Protection Agency
and by the California Air Resources Board
(also known as CARB). For warranty information,
refer to the last pages of this manual.
For item 69730: The emission control system for
this Engine is warranted for standards set by the
U.S. Environmental Protection Agency. For warranty
information, refer to the last pages of this manual.
WARNING! DO NOT INSTALL THIS ENGINE ON A VEHICLE.
NOT FOR HIGHWAY USE. FOLLOW ALL APPLICABLE LAWS FOR INSTALLATION AND USE.
Engine Controls
SETUP
Air Filter
Fuel Cap
OPERATION
Starter
Handle
Muffler
Oil Drain Plug
MAINTENANCE
Throttle
Dipstick
Choke
Fuel Valve
Engine
Switch
Page 6
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
High Altitude Operation Above 3000 feet
The fuel system on this engine may be influenced by operation at higher altitudes.
Proper operation can be ensured by installing an altitude kit at altitudes higher than 3000 ft. above sea level.
At elevations above 8000 ft, the engine may experience decreased performance, even with the proper main jet.
Operating this engine without the proper altitude kit installed may increase the engine’s emissions and
decrease fuel economy and performance. The kit should be installed by a qualified mechanic.
SAFETY
At high altitudes, the engine’s carburetor, governor (if so equipped), and any other parts that control
the fuel-air ratio will need to be adjusted by a qualified mechanic to allow efficient high-altitude
use and to prevent damage to the engine and any other devices used with this product.
WARNING! TO PREVENT SERIOUS INJURY FROM FIRE:
Follow kit procedures in a well-ventilated area away from ignition sources.
If the engine is hot from use, shut the engine off and wait for it to cool before proceeding. Do not smoke.
NOTICE Warranty void if necessary adjustments are not made for high altitude use.
1. Turn off the engine.
Carburetor
Assembly
2. Close the fuel valve.
3. Place a bowl under the fuel cup to catch any spilled fuel.
Fuel Cup Seal
4. Unthread the bolt holding the fuel cup.
CAUTION! Carburetor bowl may have gas in it
which will leak upon removing the bolt.
SETUP
High Altitude Kit Installation Instructions
Mixing Tube
(might remain
inside carburetor)
5. Remove the bolt, bolt seal, fuel cup, fuel cup seal and main jet
from the body of the carburetor assembly. A carburetor screwdriver
(not included) is needed to remove and install the Main Jet.
Note: The mixing tube is held in place by the main jet and
might fall out when it is removed. If it falls out, replace it in
the same orientation before replacing the main jet.
Fuel Cup
6. Replace the main jet with the replacement jet
needed for your altitude range (part 1 or 2).
Bolt Seal
Note: The Fuel cup seal and bolt seal may be damaged during
removal and should be replaced with the new ones from the kit.
Bolt
7. Replace the Fuel Cup Seal
(4), fuel cup, Bolt Seal (3) and bolt. Tighten in place.
CAUTION: Do not cross thread Bolt when tightening. Finger tighten first and
then use a wrench to make sure the Bolt is properly threaded.
OPERATION
Main Jet
8. Wipe up any spilled fuel and allow excess to evaporate before starting engine.
To prevent FIRE, do not start the engine while the smell of fuel hangs in the air.
ITEM 69727 / 69730
Part
Description
Qty
1
Main Jet 3000-6000 ft.
1
2
Main Jet 6000-8000 ft.
1
3
Bolt Seal
1
4
Fuel Cup Seal
1
For technical questions, please call 1-800-520-0882.
MAINTENANCE
Altitude Kit Parts List
Page 7
Operation
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
SAFETY
Pre-Start Checks
Inspect engine and equipment looking for damaged, loose, and missing parts before set up
and starting. If any problems are found, do not use equipment until fixed properly.
Checking and Filling Engine Oil
SETUP
NOTICE: Your Warranty is VOID if the engine’s
crankcase is not properly filled with oil before
each use. Before each use, check the oil level.
Do not run the engine with low or no engine oil.
Running the engine with no or low engine oil
WILL permanently damage the engine.
Full level
Full level
1. Make sure the engine is stopped and is level.
2. Close the Fuel Valve.
3. Clean the top of the Dipstick and the area around it.
Remove the Dipstick by threading it counterclockwise,
and wipe it off with a clean lint free rag.
4. Reinsert the Dipstick without threading it in and
remove it to check the oil level. The oil level
should be up to the full level as shown above.
5. If the oil level is at or below the low mark add the
appropriate type of oil until the oil level is at the
proper level. SAE 10W-30 oil is recommended
for general use. (The SAE Viscosity Grade chart
on page 13 in the Service section shows other
viscosities to use in different average temperatures.)
OPERATION
6. Thread the dipstick back in clockwise.
NOTICE: Do not run the engine with too little oil.
The engine will be permanently damaged.
MAINTENANCE
Page 8
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
Checking and Filling Fuel
2. Unscrew and remove the Fuel Cap.
3. If needed, fill the Fuel Tank to about 1 inch
under the fill neck of the Fuel Tank with
87 octane or higher unleaded gasoline.
Note: Do not use gasoline that has been stored in a
metal fuel container or a dirty fuel container. It can
cause particles to enter the carburetor, affecting
engine performance and/or causing damage.
4. Then replace the Fuel Cap.
5. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
SAFETY
1. Clean the Fuel Cap and the area around it.
Note: Do not use gasoline containing more than
10% ethanol (E10). Do not use E85 ethanol.
SETUP
WARNING! TO PREVENT SERIOUS
INJURY FROM FIRE:
Fill the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before adding fuel.
Do not smoke.
Starting the Engine
Before Starting the Engine
MAINTENANCE
OPERATION
Before starting the engine:
a. Follow the Set Up Instructions in the equipment manual to prepare the equipment.
b. Inspect the equipment and engine.
c. Fill the engine with the proper amount and type of both fuel and oil.
d. Read the Equipment Operation section in the equipment manual.
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 9
Manual Start
SAFETY
1. To start a cold engine, move the Choke to the
CHOKE position.
To restart a warm engine, leave the Choke in the
RUN position.
1
CHOKE
2. Open the Fuel Valve.
RUN
SETUP
2
3. Slide the Throttle or Speed Control Lever to 1/3
away from the SLOW position (the “turtle”).
Note: Some tools have a Speed Control Lever located
elsewhere on the tool which functions the same as the
Throttle. Use the Speed Control Lever in place of the Throttle
when the tool is so equipped.
3
OPERATION
O
OFF
4. Turn the Engine Switch on.
MAINTENANCE
5. Grip the Starter Handle of the Engine loosely and pull
it slowly several times to allow the gasoline to flow into
the Engine’s carburetor. Then pull the Starter Handle
gently until resistance is felt. Allow Cable to retract fully
and then pull it quickly. Repeat until the engine starts.
ON
ON
I
4
5
Note: Do not let the Starter Handle snap back against the engine.
Hold it as it recoils so it doesn't hit the engine.
Page 10
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
6
SAFETY
6. Allow the Engine to run for several seconds.
Then, if the Choke lever is in the CHOKE position,
move the Choke Lever very slowly to its RUN position.
Note: Moving the Choke Lever too fast could stall the engine.
CHOKE
RUN
IMPORTANT: Allow the engine to run at no load for five minutes with no
load after each start-up so that the engine can stabilize.
7. Adjust the Throttle as needed.
8. Break-in Period:
a. Breaking-in the engine will help to ensure proper equipment and engine operation.
b. The operational break-in period will last about 3 hours of use. During this period:
• Do not apply a heavy load to the equipment.
SETUP
• Do not operate the engine at its maximum speed.
c. The maintenance break-in period will last about 20 hours of use. After this period:
• Change the engine oil.
Under normal operating conditions subsequent maintenance follows the schedule
explained in the MAINTENANCE AND SERVICING section.
1. To stop the engine in an emergency,
turn the Engine Switch off.
OFF
O
OPERATION
Stopping the Engine
I
2. Under normal conditions, use the following procedure:
a. Slide the Throttle or Speed Control
Lever to SLOW (the “turtle”).
MAINTENANCE
b. Turn the Engine Switch off.
c. Close the Fuel Valve.
WARNING! The fuel valve must be closed before moving
the engine to prevent fuel leakage and fire.
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 11
Maintenance
WARNING
SAFETY
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING:
Turn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool, and disconnect
the spark plug cap before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE:
Do not use damaged equipment. If abnormal noise, vibration, or excess
smoking occurs, have the problem corrected before further use.
Follow all service instructions in this manual. The engine may fail critically if not serviced properly.
Many maintenance procedures, including any not detailed in this manual, will need to be
performed by a qualified technician for safety. If you have any doubts about your ability to safely
service the equipment or engine, have a qualified technician service the equipment instead.
Cleaning, Maintenance, and Lubrication Schedule
SETUP
Note: This maintenance schedule is intended solely as a general guide. If performance decreases or if
equipment operates unusually, check systems immediately. The maintenance needs of each piece of equipment
will differ depending on factors such as duty cycle, temperature, air quality, fuel quality, and other factors.
Note: The following procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the engine and equipment.
Before
Each Use
Procedure
Monthly or
Every 3 mo. or Every 6 mo. or
every 20
50 hr. of use 100 hr. of use
hr. of use
Yearly or
every 300
hr. of use
Every
2 Years
Brush off outside of engine
Check engine oil level
Check air cleaner
Check deposit cup
OPERATION
Change engine oil
*
Clean/replace air cleaner
Check and clean spark plug
1. Check/adjust idle speed
2. Check/adjust valve clearance
3. Clean fuel tank, strainer
and carburetor
**
4. Clean carbon build-up from
combustion chamber
Replace fuel line if necessary
**
**
*Service more frequently when used in dusty areas.
**These items should be serviced by a qualified technician.
MAINTENANCE
Page 12
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
Checking and Filling Fuel
Engine Oil Change
WARNING! TO PREVENT SERIOUS
INJURY FROM FIRE:
Fill the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before adding fuel.
Do not smoke.
CAUTION! Oil is very hot during operation and can
cause burns. Wait for engine to cool before changing oil.
1. Clean the Fuel Cap and the area around it.
4. Remove the drain plug and, if possible,
tilt the crankcase slightly to help drain
the oil out. Recycle used oil.
5. Replace the drain plug and tighten it.
6. Clean the top of the Dipstick and the area around it.
Remove the Dipstick by threading it counterclockwise,
and wipe it off with a clean lint free rag.
Full level
Full level
Max Fuel
DO NOT OVERFILL!
WARNING! TO PREVENT FUEL
LEAKAGE AND FIRE HAZARD, do not fill
fuel above the bottom of fuel strainer.
Note: Do not use gasoline containing more than
10% ethanol (E10). Do not use E85 ethanol.
7. Add the appropriate type of oil until the oil level is at
the full level. SAE 10W-30 oil is recommended for
general use.
The SAE Viscosity Grade chart shows other
viscosities to use in different average temperatures.
SAE Viscosity Grades
Note: Do not use gasoline that has been stored in a
metal fuel container or a dirty fuel container. It can
cause particles to enter the carburetor, affecting
engine performance and/or causing damage.
30
10W-30
4. Then replace the Fuel Cap.
5. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
SAFETY
3. Place a drain pan (not included) underneath
the crankcase’s drain plug.
SETUP
3. If needed, fill the Fuel Tank to about 1 inch under
the fill neck of the Fuel Tank with 87 octane or
higher unleaded gasoline. Fill to the bottom
of the fuel strainer ONLY, see below.
2. Close the Fuel Valve.
5W-30
-20
0
20
40
60
80
Average outdoor temperature
100°F
OPERATION
2. Unscrew and remove the Fuel Cap.
1. Make sure the engine is stopped and is level.
8. Thread the dipstick back in clockwise.
MAINTENANCE
CAUTION! Do not run the engine with too little oil.
The engine will be permanently damaged.
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 13
Air Filter Element Maintenance
1. Remove the air filter cover and the
air filter elements and check for dirt.
Clean or replace as described below.
2. Cleaning:
SAFETY
• For “paper” filter elements:
To prevent injury from dust and debris,
wear ANSI-approved safety goggles,
NIOSH-approved dust mask/respirator, and
heavy-duty work gloves. In a well-ventilated
area away from bystanders, use pressurized
air to blow dust out of the air filter.
If this does not get the filter clean, replace it.
• For foam filter elements:
Wash the element in warm water and
mild detergent several times. Rinse.
Squeeze out excess water and allow it to dry
completely. Soak the filter in lightweight oil
briefly, then squeeze out the excess oil.
SETUP
3. Install the new filter or the cleaned filter.
Secure the Air Cleaner Cover before use.
Spark Plug Maintenance
Spark
Plug
Cap
1. Disconnect spark plug cap from end of plug.
Clean out debris from around spark plug.
2. Using a spark plug wrench, remove the spark plug.
3. Inspect the spark plug:
If the electrode is oily, clean it using a clean, dry rag.
If the electrode has deposits on it, polish it using
emery paper. If the white insulator is cracked or
chipped, the spark plug needs to be replaced.
Recommended Spark Plugs
NGK®
NHSP® / TORCH®
BP-6ES
F6TC
NOTICE: Using an incorrect spark
plug may damage the engine.
4. When installing a new spark plug, adjust the
plug’s gap to the specification on the Technical
Specifications chart. Do not pry against the
electrode, the spark plug can be damaged.
OPERATION
5. Install the new spark plug or the cleaned spark plug
into the engine. Gasket-style: Finger-tighten until the
gasket contacts the cylinder head, then tighten about
1/2-2/3 turn more.
Non-gasket-style: Finger-tighten until the plug
contacts the head, then tighten about 1/16 turn more.
NOTICE: Tighten the spark plug properly.
If loose, the spark plug will cause the engine to overheat.
If overtightened, the threads in the
engine block will be damaged.
6. Apply dielectric spark plug boot protector
(not included) to the end of the spark
plug and reattach the wire securely.
MAINTENANCE
Page 14
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
Storage
WARNING! TO PREVENT SERIOUS
INJURY FROM FIRE:
Drain the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before draining fuel.
Do not smoke.
a. Place a funnel leading to a proper gasoline
container below the carburetor.
Sediment Cup
(some engines)
Drain Plug
b. Remove the drain bolt from the bottom of the
carburetor bowl and allow the fuel to drain.
b. Clean out area around spark plug. Remove
spark plug and pour one tablespoon of engine
oil into cylinder through spark plug hole.
c. Replace spark plug, but leave spark
plug cap disconnected.
d. Pull Starter Handle to distribute oil in cylinder.
Stop after one or two revolutions when you
feel the piston start the compression stroke
(when you start to feel resistance).
4. BATTERY:
Disconnect battery cables (if equipped).
Recharge batteries monthly while in storage.
5. STORAGE AREA:
Cover and store in a dry, level, well-ventilated
area out of reach of children. Storage area
should also be away from ignition sources, such
as water heaters, clothes dryers, and furnaces.
6. AFTER STORAGE:
Before starting the engine after storage, keep in
mind that untreated gasoline will deteriorate quickly.
Drain the fuel tank and change to fresh fuel if
untreated gasoline has been sitting for a month,
if treated gasoline has been sitting beyond
the fuel stabilizer’s recommended time
period, or if the engine does not start.
MAINTENANCE
c. Remove the small sediment cup next to the bowl
and allow the fuel to drain from there as well.
a. Change engine oil.
SAFETY
2. FUEL:
3. LUBRICATION:
SETUP
1. CLEANING:
Wait for engine to cool, then clean engine with
dry cloth. NOTICE: Do not clean using water.
The water will gradually enter the engine
and cause rust damage. Apply a thin coat
of rust preventive oil to all metal parts.
d. Open the fuel valve. After all fuel has
drained, reinstall the drain bolt and sediment
cup (if equipped). Tighten securely.
OPERATION
When the equipment is to remain idle for longer than
20 days, prepare the engine for storage as follows:
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 15
Troubleshooting
Possible Causes
Engine will not start
FUEL RELATED:
1. No fuel in tank or fuel valve closed.
2. Choke not in CHOKE position, cold engine.
3. Gasoline with more than 10% ethanol
used. (E15, E20, E85, etc.)
SAFETY
Problem
Probable Solutions
9. Clogged Fuel Filter.
FUEL RELATED:
1. Fill fuel tank and open fuel valve.
2. Move Choke to CHOKE position.
3. Clean out ethanol rich gasoline from fuel
system. Replace components damaged
by ethanol. Use fresh 87+ octane
unleaded gasoline only.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
4. Use fresh 87+ octane unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
5. Pull on Starter Handle to prime.
6. Clean out passageways using
fuel additive. Heavy deposits
may require further cleaning.
7. Gently tap side of carburetor float
chamber with screwdriver handle.
8. Turn Choke to RUN position.
Remove spark plug and pull the start
handle several times to air out the
chamber. Reinstall spark plug and
set Choke to CHOKE position.
9. Replace Fuel Filter.
IGNITION (SPARK) RELATED:
1. Spark plug cap not connected securely.
2. Spark plug electrode wet or dirty.
3. Incorrect spark plug gap.
4. Spark plug cap broken.
5. Circuit breaker tripped
(electric start models only).
6. Incorrect spark timing or
faulty ignition system.
IGNITION (SPARK) RELATED:
1. Connect spark plug cap properly.
2. Clean spark plug.
3. Correct spark plug gap.
4. Replace spark plug cap.
5. Reset circuit breaker. Check wiring and
starter motor if breaker continues to trip.
6. Have qualified technician diagnose/
repair ignition system.
4. Low quality or deteriorated, old gasoline.
5. Carburetor not primed.
6. Dirty fuel passageways.
SETUP
7. Carburetor needle stuck.
Fuel can be smelled in the air.
8. Too much fuel in chamber. This can be
caused by the carburetor needle sticking.
OPERATION
MAINTENANCE
COMPRESSION RELATED:
COMPRESSION RELATED:
1. Cylinder not lubricated. Problem after long 1. Pour tablespoon of oil into spark
storage periods.
plug hole. Crank engine a few
times and try to start again.
2. Loose or broken spark plug. (Hissing
2. Tighten spark plug. If that does not work,
noise will occur when trying to start.)
replace spark plug. If problem persists,
may have head gasket problem, see #3.
3. Loose cylinder head or damaged
3. Tighten head. If that does not remedy
head gasket. (Hissing noise will
problem, replace head gasket.
occur when trying to start.)
4. Engine valves or tappets
4. Have qualified technician diagnose/
mis-adjusted or stuck.
repair ignition system.
Follow all safety precautions whenever diagnosing or servicing the equipment or engine.
Page 16
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
5. Incorrect compression.
Engine stops
suddenly
1. Low oil shutdown.
2. Fuel tank empty or full of impure or low
quality gasoline.
3. Defective fuel tank cap creating
vacuum, preventing proper fuel flow.
4. Faulty magneto.
5. Disconnected or improperly
connected spark plug cap.
1. Check wire connections.
2. Re-gap or replace spark plug.
3. Replace spark plug cap.
4. Use only fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
5. Diagnose and repair compression.
(Use Engine will not start:
COMPRESSION RELATED section.)
1. Fill engine oil to proper level. Check
engine oil before EVERY use.
2. Fill fuel tank with fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
3. Test/replace fuel tank cap.
4. Have qualified technician service magneto.
5. Secure spark plug cap.
Engine stops when
under heavy load
1. Dirty air filter
2. Engine running cold.
1. Clean or replace element.
2. Allow engine to warm up prior
to operating equipment.
Engine knocks
1. Old or low quality gasoline.
1. Fill fuel tank with fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
2. Do not exceed equipment’s load rating.
3. Have qualified technician
diagnose and service engine.
2. Engine overloaded.
3. Incorrect spark timing, deposit
buildup, worn engine, or other
mechanical problems.
Engine backfires
1. Impure or low quality gasoline.
2. Engine too cold.
3. Intake valve stuck or overheated engine.
4. Incorrect timing.
1. Fill fuel tank with fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
2. Use cold weather fuel and oil
additives to prevent backfiring.
3. Have qualified technician
diagnose and service engine.
4. Check engine timing.
SAFETY
1. Spark plug cap loose.
2. Incorrect spark plug gap or
damaged spark plug.
3. Defective spark plug cap.
4. Old or low quality gasoline.
Probable Solutions
SETUP
Engine misfires
Possible Causes
OPERATION
Problem
MAINTENANCE
Follow all safety precautions whenever diagnosing or servicing the equipment or engine.
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 17
Warranties
Limited 90 Day Warranty
SAFETY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
SETUP
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Emission Control System Warranty
California and United States Emission Control
Defects Warranty Statement
(for Model 68727)
OPERATION
The California Air Resources Board (herein CARB), the
United States Environmental Protection Agency (herein EPA), and
Harbor Freight Tools (herein HFT) are pleased to explain the emission
control system warranty on your 2014-2015 Small Off-Road Engine
(herein engine). In California, the engine must be designed, built and
equipped to meet the State’s stringent anti-smog standards. Elsewhere
within the United States, new off-road, spark-ignition engines certified
for model year 2014-2015, must meet similar standards set forth by
the EPA. HFT must warrant the emission control system on your
engine for the periods of time described below, provided there has
been no abuse, neglect or improper maintenance of your engine.
Manufacturer’s Warranty Coverage
The 2014-2015 and later engines are warranted for two (2) years.
If any emission-related part on your engine is defective,
the part will be repaired or replaced by HFT.
Harbor Freight Tools Emission Control
Defects Warranty Coverage
Engines are warranted for a period of two (2) years relative
to emission control parts defects, subject to the provisions
set forth below. If any emission related part on your engine is
defective, the part will be repaired or replaced by HFT.
Owner’s Warranty Responsibilities
•
Your emission control system may include parts
such as the carburetor or fuel-injection system, and
the ignition system. Also included may be hoses, belts,
connectors and other emission-related assemblies.
Where a warrantable condition exists, HFT will repair your
engine at no cost to you including diagnosis, parts and labor.
•
United States Emission Control Defects
Warranty Statement
(for Model 68730)
•
MAINTENANCE
The United States Environmental Protection Agency (herein EPA)
and Harbor Freight Tools (herein HFT) are pleased to explain the
emission control system warranty on your 2014-2015 Small Off-Road
Engine (herein engine). Within the United States, new off-road, sparkignition engines certified for model year 2014-2015 and later, must be
designed, built and equipped to meet the stringent anti-smog standards
set forth by the EPA. HFT must warrant the emission control system
on your engine for the periods of time described below, provided there
has been no abuse, neglect or improper maintenance of your engine.
As the engine owner, you are responsible for the performance
of the required maintenance listed in your Owner’s Manual.
HFT recommends that you retain all receipts covering
maintenance on your engine, but HFT cannot deny warranty
solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance.
As the engine owner, you should, however, be aware
that HFT may deny you warranty coverage if your engine
or a part has failed due to abuse, neglect, improper
maintenance, or unapproved modifications.
You are responsible for shipping your engine to a HFT warranty
station as soon as a problem exists. Contact the HFT Customer
Service department at the number below to make shipping
arrangements. The warranty repairs should be completed
in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty
rights and responsibilities, you should contact the
Harbor Freight Tools Customer Service Department at 1-800-520-0882.
Your emission control system may include parts such as
the carburetor or fuel-injection system, and the ignition system.
Also included may be hoses, belts, connectors and other
emission-related assemblies.
Where a warrantable condition exists, HFT will repair your engine
at no cost to you including diagnosis, parts and labor.
Page 18
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
No Charge Repair or Replacement
Repair or replacement of any warranted part will be performed at
no charge to the owner if the work is performed through a warranty
station authorized by HFT. For emissions warranty service,
contact the HFT Customer Service Department at 1-800-520-0882.
3.
Consequential Damages Coverage
6.
Warranted Parts
1)
Coverage under this warranty shall also extend to the failure
of any engine components caused by the failure of any
warranted part while it is still covered under this warranty.
4.
Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions
of the HFT warranty policy explained in the box at the top of the
previous page. HFT shall not be liable for any loss of use of
the engine, for any alternative usage, for any damage to goods,
loss of time, or inconvenience. Warranty coverage shall also be
excluded for any part which fails, malfunctions, or is damaged
due to failure to follow the maintenance and operating instructions
set forth in the Owner’s Manual including, but not limited to:
a) Use of parts which are not authorized by HFT
b) Improper installation, adjustment or repair of
the engine or of any warranted part unless
performed by an authorized warranty center
c) Failure to follow recommendations on fuel
use contained in the Owner’s Manual
d) Improper or inadequate maintenance of any warranted parts
e) Repairs performed outside of the authorized
warranty service dealers
f)
Alterations by changing, adding to or
removing parts from the engine.
2)
3)
4)
5)
6)
7)
Fuel Metering System
i)
Carburetor and its internal parts.
ii) Air/fuel ratio feedback and control system.
iii) Cold start enrichment system.
iv) Fuel Tank.
Air Induction System
i)
Controlled hot air intake system.
ii) Intake manifold.
iii) Air filter.
Ignition System
i)
Spark Plugs.
ii) Magneto or electronic ignition system.
iii) Spark advance/retard system.
Exhaust Gas Recirculation (EGR) System (if so equipped)
i)
EGR valve body, and carburetor spacer.
ii) EGR rate feedback and control system.
Air Injection System
i)
Air pump or pulse valve.
ii) Valves affecting distribution of flow.
iii) Distribution manifold.
Catalyst or Thermal Reactor System (if so equipped)
i)
Catalytic converter.
ii) Thermal reactor.
iii) Exhaust manifold.
Particulate Controls
Traps, filters, precipitators, and any other device
used to capture particulate emissions.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
ITEM 69727 / 69730
For technical questions, please call 1-800-520-0882.
Page 19
SAFETY
Length of Coverage
SETUP
Component parts which are not scheduled for replacement
as required maintenance or are scheduled only for regular
inspection to the effect of “repair or replace as necessary”
are warranted for the warranty period. Any warranted part
which is scheduled for replacement as required maintenance
is warranted for the period of time up to the first scheduled
replacement point for that part. Any replacement part, provided
it is equivalent in durability and performance, may be used
in performance of maintenance or repairs. The owner is
responsible for commissioning a qualified technician/mechanic
to perform all required maintenance, as outlined in the
Inspection, Cleaning, and Maintenance section in this manual.
HFT warrants to a first retail purchaser and each
subsequent purchaser that the engine is free from
defects in materials and workmanship that cause the
failure of warranted parts for a period of two (2) years
after the date of delivery to the first retail purchaser.
2.
Service and Maintenance
OPERATION
1.
5.
MAINTENANCE
Harbor Freight Tools Emission Control
Defects Warranty Provisions
Parts Lists and Diagrams
69727 Parts List
SAFETY
Part
SETUP
OPERATION
MAINTENANCE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Description
Gasket, Cylinder Head
Cover Subassembly, Cylinder Head
Gasket, Cylinder Head Cover
Tube, Breather
Bolt
Stud
Stud
Pin
Bolt, Cylinder Head
Plug, Spark
Head Subassembly, Cylinder
Crankcase Subassembly
Sensor, Engine Oil
Gear Asm, Governor
Arm, Governor
Bolt, Drain Plug
Washer, Flat
Bearing, Deep Groove Ball
Seal, Oil
Washer, Flat
Cotter
Bolt
Cover, Crankcase
Gasket, Crankcase
Pin
Dipstick Subassembly, Oil
Plug Subassembly, Engine Oil
Seal, Oil
Bolt
Crankshaft Asm.
Clip, Piston Pin
Piston
Pin, Piston
Rod, Connecting
Primary Ring
Secondary Ring
Ring Set, Oil
Camshaft Asm.
Valve, Exhaust
Valve, Intake
Seat, Valve Spring
Clamp, Valve Lock
Guide, Seal
Spring, Valve
Plate Subassembly, Lifter Stopper
Bolt, Rocker Shaft
Rocker, Valve
Page 20
Qty
1
1
1
1
4
2
2
2
4
1
1
1
1
1
1
2
2
2
1
1
1
2
1
1
2
1
1
1
6
1
2
1
1
1
1
1
1
1
1
1
2
4
2
2
1
2
2
Part
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Description
Nut, Valve Adjusting
Nut, Valve Lock
Tappet, Valve
Lifter, Valve
Starter Asm, Recoil
Bolt
Shroud
Bolt
Shroud, Cylinder Body
Bolt
Shield,Lower
Bolt
Protector, Oil
Collar
Switch Subassembly, Stop Engine
Gasket, Carburetor Insulator
Plate, Carburetor Insulator
Gasket, Carburetor
Gasket, Air Cleaner
Nut
Cleaner, Air
Gasket, Exhaust Outlet
Nut
Muffler Asm.
Tank, Fuel
Strainer, Fuel
Cover, Fuel Tank
Outlet Subassembly, Fuel Tank Oil
Collar
Tube, Fuel
Jacket, Rubber
Nut
Nut, Flywheel
Pulley, Starter
Impeller
Flywheel Subassembly
Bolt
Coil, Ignition
Support Subassembly, Governor
Nut
Bolt, Governor Support
Spring, Governor
Rod, Governor
Spring, Throttle Valve Returning
Control Asm, Throttle
Bolt
For technical questions, please call 1-800-520-0882.
Qty
2
2
2
2
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
2
ITEM 69727 / 69730
SAFETY
9
10
69
7
71
7
29
29
29
27
29
35 36 37
1
29
29
31
8
8
28
23
32
31
18
33
49 48
26
25
24
34
47
47
51
46
46
50
45
38
43 4 2
4 2 39
50
4 1 44
4 1 44 4 3
51
25
SETUP
70
3
9
6
49 48
30
22
40
22
91
93
13
90
14
92
89
93
88
18
16
17
15
21
86 87
67
68
67
20
78
19
85
75
84
84
76
77
17
83
79
16
79
82
57
72
81
57
80
58
56
73
52
74
61
59
55
Note: If product has no serial number,
record month and year of purchase instead.
Record Product’s Serial Number Here:
12
OPERATION
70
2
9
11
6
67
66
60
54
55
MAINTENANCE
5
4
9
69727 Assembly Diagram
5
5
5
63
64
65
Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.
53
62
55
55
53
53
55
Page 21
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
69730 Parts List
Part
SAFETY
SETUP
OPERATION
MAINTENANCE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Description
Gasket, Cylinder Head
Cover Subassembly, Cylinder Head
Gasket, Cylinder Head Cover
Tube, Breather
Bolt
Stud
Stud
Stud
Pin
Bolt, Cylinder Head
Plug, Spark
Head Subassembly, Cylinder
Crankcase Subassembly
Sensor, Engine Oil
Gear Assy, Governor
Arm, Governor
Bolt, Drain Plug
Washer
Bearing
Seal, Oil
Washer
Pin
Bolt
Cover, Crankcase
Bearing
Seal, Oil
Gasket, Crankcase
Pin
Dipstick Subassembly, Oil
Plug Subassembly, Engine Oil
Bolt
Crankshaft Assy.
Clip, Piston Pin
Piston
Pin, Piston
Rod, Connecting
Ring, Primary
Ring, Secondary
Ring Set, Oil
Camshaft Assy.
Valve, Exhaust
Valve, Intake
Seat, Valve Spring
Retainer, Exhaust Valve
Rotator, Valve
Guide, Seal
Tappet, Valve
Lifter, Valve
Plate Subassembly, Lifter Stopper
Bolt, Valve Adjusting
Rocker, Valve
Page 22
Qty
1
1
1
1
4
1
1
2
2
4
1
1
1
1
1
1
2
2
1
1
1
1
2
1
1
1
1
2
1
1
6
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
Part
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
Description
Nut, Valve Adjusting
Nut, Valve Lock
Spring, Valve
Starter Assy, Recoil
Bolt
Shroud
Shroud, Cylinder Body
Shield,Lower
Protector, Oil
Switch Subassembly, Stop Engine
Bolt
Bolt
Collar
Bolt
Bolt
Carburetor Assy.
Gasket, Air Cleaner
Gasket, Carburetor
Plate, Carburetor Insulator
Gasket, Carburetor Insulator
Nut
Cleaner, Air
Jacket, Rubber
Gasket, Exhaust Outlet
Nut
Muffler Assy
Tank, Fuel
Strainer, Fuel
Cover, Fuel Tank
Outlet Subassembly, Fuel Tank Oil
Clamp
Tube, Fuel
Bolt
Nut
Nut, Flywheel
Pulley,Starter
Impeller
Flywheel Subassembly
Bolt
Coil, Ignition
Control Assy, Throttle
Bolt
Spring, Governor
Rod, Governor
Spring, Throttle Valve Returning
Bolt, Governor Support
Nut
Support Subassembly, Governor
Valve, One Way
Clamp
Hose, Fuel Steam Rubber
For technical questions, please call 1-800-520-0882.
Qty
2
2
2
1
3
1
1
1
1
1
2
1
1
1
4
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
3
1
1
2
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
ITEM 69727 / 69730
SAFETY
76
76
10
11
8
75
8
77
6
31
31
1
31
9
31
31
9
33
31
30
37 38 39
7
26
24
34
35
25
33
29
28
51
51
36
53 52
53 52
27
28
47
47
49
43 5446
44 54 41
48
50
50
45
48
SETUP
3
12
40
42
14
93
23
93
32
23
15
92
95
97
94
96
19
17
98
99
16
22
18
73
21
81
82
85
85
17
82
78
89
18
102
101
90
90
82
74
20
91
83
13
84
OPERATION
2
10
10
10
4
67
72
72
88
62
79
100
86
80
87
62
58
59
55
64
66
65
60
57
63
56
MAINTENANCE
5
5
69730 Assembly Diagram
5
5
71
70
69
68
66
61
56
56
66
66
Page 23
For technical questions, please call 1-800-520-0882.
ITEM 69727 / 69730
Mounting Hole Diagram
6.38 in. / 162mm
2.6 in. / 66mm
3.17 in. / 80.5mm
2.97 in. / 75.5mm
1.6 in. / 40.5mm
Power Take-Off Diagram
2.43 in. / 61.7mm
5/16-24UNF
0.67 in.
/ 17mm
Ø3.625 in. / 92mm
Note:
4.17 in. / 106mm
4x5/16-24UNF
Ø0.75 in. / 19.05mm
0.64 in.
/ 16.36mm
0.1875 in. / 4.78mm
Not to scale.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-800-520-0882
5/16-24UNF
1.79 in. / 45.5mm