Harbor Freight Tools 4_in_1 Product manual

Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
4 in 1
POWER PACK
CHARGE COMPLETELY
IMMEDIATELY AFTER
PURCHASE.
Fully recharge after
each jump-start.
Fully recharge monthly to
ensure long battery life.
REV 14f
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2014 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety
Safetye��������������������������������������������������������� 2
Specifications.............................................. 4
Setup........................................................... 5
Operationa���������������������������������������������������� 8
Maintenancei���������������������������������������������� 10
Parts List and Diagram............................... 11
Warranty..................................................... 12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
SETUP
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Operation
Canadian Standards Association
Underwriters Laboratories, Inc.
Maintenance
V
~
A
CCA
RC
Ah
Page 2
WARNING marking
concerning Risk of Eye Injury.
Wear ANSI‑approved
splash‑resistant safety goggles.
Read the manual before
set-up and/or use.
Volts
Alternating Current
Amperes
WARNING marking
concerning Risk of Fire.
Follow connection procedure.
Cold Cranking Amps
Reserve Capacity
Ampere-hours
For technical questions, please call 1-888-866-5797.
Item 62374
Safety Warnings and Precautions
Safety
General Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
WARNING – RISK OF EXPLOSIVE GASES.
Working in vicinity of a lead-acid battery is
dangerous. Batteries generate explosive gases
during normal battery operation. For this reason,
it is of utmost importance that you follow the
instructions each time you use the Power Pack.
To reduce risk of battery explosion, follow these
instructions and those published by battery
manufacturer and manufacturer of any equipment you
intend to use in vicinity of battery. Review cautionary
marking on these products and on engine.
Work Area Safety
2. Do not operate Power Pack in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. The Power Pack
can create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away
while operating the Power Pack.
Distractions can cause you to lose control.
SETUP
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
4. Store idle equipment. Always lock up tools
and keep out of reach of children.
Electrical Safety
2. Do not operate if Power Pack has received a
sharp blow, been dropped, or otherwise damaged
in any way; take it to a qualified technician.
3. Do not leave Power Pack unattended
while switched on. It could result
in fire and property damage.
4. Do not expose to rain or wet conditions.
Water entering the Power Pack will
increase the risk of electric shock.
5. Do not use an extension cord with this item.
6. Use of an attachment not recommended or
sold by the manufacturer may result in a risk
of fire, electric shock, or injury to persons.
7. To reduce risk of damage to electric plug
and cord, pull by plug rather than cord
when disconnecting the Adapter.
8. Do not operate with damaged cord or plug.
Replace the cord or plug immediately.
Operation
1. Do not drop a metal tool onto battery. It
might spark or short-circuit battery or other
electrical part that may cause explosion.
1.
Wear ANSI-approved splash-resistant
safety goggles and heavy-duty
rubber work gloves whenever
connecting, disconnecting, or
working near battery. Battery acid
can cause permanent blindness.
Avoid touching eyes while working near battery.
2. Do not use Power Pack while you are tired
or under the influence of drugs, alcohol
or medication. A moment of inattention
while operating Power Pack may
result in serious personal injury.
3. NEVER smoke or allow a spark or flame
in vicinity of battery or engine.
Item 62374
4. If battery acid contacts skin or clothing,
wash immediately with soap and water.
If acid enters eye, immediately flood eye with
running cold water for at least 10 minutes
and get medical attention immediately.
5. Remove personal metal items such as rings,
bracelets, necklaces, and watches when working
with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld
a ring or the like to metal, causing a severe burn.
6. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
For technical questions, please call 1-888-866-5797.
Page 3
Maintenance
Personal Safety
Service
Have your Power Pack serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the Power Pack is maintained.
Safety
Power Pack Safety Warnings
1. Lead-acid batteries generate hydrogen gas when
charging. Hydrogen gas is explosive. Only use
the Jump-Start system in a well-ventilated area.
2. Jump Starting A Vehicle
a. Use the Power Pack for jump starting
a LEAD-ACID battery only.
b. For emergency use only. Do not use the Power
Pack as a replacement for a vehicle battery.
c. Be sure area around battery is well ventilated
while battery is being jump started.
d. NEVER jump start a frozen battery.
k. Locate Power Pack as far away from
battery as battery cables permit.
3. Maintain labels and nameplates on the Power Pack.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
4. WARNING: This product contains lead, a chemical
known to the State of California to cause cancer
and birth defects or other reproductive harm.
(California Health & Safety Code § 25249.5, et seq.)
SETUP
5. WARNING: This product contains or, when
used, produces a chemical known to the State
of California to cause cancer and birth defects
or other reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
e. Do not attempt to jump start a vehicle with
a non‑rechargeable or defective battery.
f. Study all battery manufacturer’s specific
precautions for jump starting.
g. DO NOT TOUCH POSITIVE AND NEGATIVE
BATTERY CLAMPS TOGETHER.
h. Unplug the Power Pack from its Adapter
before connecting its cables to a battery.
i. Connect and disconnect battery cable
clamps only after setting any Jump Starter
switches to OFF position.
Operation
j. Connect cables to proper polarities. Connect
black cable to negative body ground and
red cable to positive battery terminal.
6. WARNING: The cord of this product contains
lead, a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
7. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Specifications
Maintenance
Cranking Amps
330
Battery
12VDC, 17Ah
Battery Cables
42″ L
Maximum Air Pressure
250 PSI
Functions: 12 Volt Jump-Starter, Air Compressor,
12VDC Power Supply, and 3 LED Work Light
Specification
Page 4
For technical questions, please call 1-888-866-5797.
Item 62374
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this
manual including all text under subheadings therein before setup or use of this product.
SAFETY
Note: For additional information regarding the parts listed in the following pages,
refer to Parts List and Diagram on page 11.
Functions
Clamp Power
Switch
Work
Light
Connection
Indicator Light
Negative
Battery
Cable
Positive
Battery
Cable
SETUP
Charge
Indicator
Lights
USB Port
12VDC
Outlet
Battery Test
Button /
USB Power
Button
120VAC
Charging
Input Plug
(on back)
OPERATION
Work Light
Button
Air
Pressure
Gauge
MAINTENANCE
Air Compressor
Switch
Air Hose
Comparment
Figure A
Item 62374
For technical questions, please call 1-888-866-5797.
Page 5
Charging the Power Pack
WARNING! Always charge on a non-flammable surface.
Approximate
AC Charge Time
Safety
Press and hold the Battery Test Button on the front
of the unit to check the battery power level.
Initial Charge:
48 hours
Recharge:
30 hours
a. Green light is ready for use.
b. Yellow light needs to be charged.
c. Red light should be charged immediately.
Figure B
1. Plug the 120VAC Adapter into a 2 or 3-prong outlet.
3. The Charging Indicator lights will illuminate in a
cycle from red, to yellow, to green while the unit
is charging. The green Charging Indicator light
will remain on after charging is complete.
The battery power level must be checked
periodically when charging, and the Power Pack
must be unplugged when it is fully charged.
2. Slide the Adapter socket on the 120VAC Charging
Input on the back of the Power Pack.
NOTE: FAILURE TO RECHARGE POWER
PACK WILL VOID WARRANTY.
Turn the Clamp Power Switch on front
of unit to the OFF position.
Note: Before initial use, completely
charge the Power Pack.
SETUP
4. Recharge:
a. When yellow light comes on while
pressing the Battery Test Button.
b. After each Jump-Start.
c. Once a month.
DO NOT EXCEED MAXIMUM CHARGING TIME
Operation
Maintenance
Page 6
For technical questions, please call 1-888-866-5797.
Item 62374
DC Appliance Compatibility
Calculate the total wattage needed to run the
appliance before operation. You do not need
to calculate startup or surge wattages.
To calculate the size of the load you plan to use
with the Power Pack, use the following formula:
Amps x Volts = Watts
For example, if you use an appliance whose
running amps total 7 amps, you will need 84
watts of power (7 amps x 12V = 84 Watts) to
run the items. This figure is within the capacity
of the unit (10 amps x 12V = 120 Watts).
The actual power usage may vary based on the
model or brand of the appliance. Check the actual
wattage of your appliances and calculate the
amount of power needed to run/charge them.
Appliance
Fluorescent Light,
Cell Phone Charger
Radio, Fan,
Depth Finder
Video Recorder/
Player, Spotlight
Small Power Tool,
Bilge Pump
Electric Cooler
Air Compressor
Estimated
Power
(watts)
Estimated
Use (hours)
4
50
9
26
15
14
24
8
48
80
3
2
Safety
The lower the amount of watts the appliance
draws, the longer the Power Pack can power
it before needing to be recharged.
Note: Use this chart as a guideline only.
SETUP
The Power Pack can run/charge 12VDC
auto, RV, marine, or other portable
appliances that draw 10 amps or less.
Maintenance
Operation
Figure C
Item 62374
For technical questions, please call 1-888-866-5797.
Page 7
Operating Instructions
Using the Work Light
Safety
1. To turn the Work Light on, press
the Work Light button.
3. To turn the Work Light off, press the
Work Light button again.
2. To turn flashing lights on, press the
Work Light button again.
Jump Starting a Vehicle
Note: Read the vehicle owner’s manual pertaining
to jump starting prior to using the Power Pack.
WARNING! DO NOT CONNECT TO THE
NEGATIVE TERMINAL OF THE BATTERY.
1. Press the Battery Test button to verify that the
Power Pack is fully charged. Recharge as
needed, following the instructions in the “Charging
the Power Pack” section on page 6.
4. When the correct connection has been made, turn
the Clamp Power Switch to the ON position.
SETUP
2. Turn off the vehicle ignition switch and all
accessories (lights, radio, climate control, etc.).
3. Turn Clamp Power Switch on the Power
Pack to their OFF position. You may
leave the Work Light on if needed.
WARNING! DO NOT TOUCH POSITIVE AND
NEGATIVE BATTERY CLAMPS TOGETHER.
5. WAIT FIVE MINUTES, then start the
vehicle. If the vehicle does not start, wait an
additional 3 minutes before trying again.
WARNING! THE VEHICLE WILL NOT START IF
YOU DO NOT WAIT AT LEAST 5 MINUTES.
6. After the vehicle is started, turn the Clamp
Power Switch to the OFF position. Remove
the black Negative Battery Cable first, and
then the red Positive Battery Cable.
3. Connect the red Positive Battery Cable to
vehicle’s positive battery terminal. Connect
the black Negative Battery Cable to a nonmoving metal part of the vehicle.
Operation
Using the Air Compressor
Tire Inflator
1. Press the Battery Test button to verify that the
Power Pack is fully charged. Recharge as needed,
following the instructions in the “Charging
the Power Pack” section on page 6.
2. Open the Air Hose Compartment on the
back of the unit and pull out the air hose.
3. Check the proper inflation level for the object that is
being inflated.
Adapter
installed
Lever
pressed
down
Air Hose
Tire Inflation
Maintenance
1. Position the Tire Inflator over the valve stem and
push down firmly, making sure it is fully seated.
2. Press the lever down. (See Figure D.)
Figure D
3. Press the Air Compressor Switch on.
Note: Monitor the Air Pressure Gauge on the
front of the unit to avoid over-inflation.
4. When the proper inflation level has been
reached, press the Air Compressor Switch off.
5. Lift the lever and remove the hose.
Page 8
For technical questions, please call 1-888-866-5797.
Item 62374
Using Hose Adapters
1. Three adapters are included with the Power Pack that
can be attached to the Tire Inflator. (See Figure E.)
2. Attach the proper adapter to the Tire
Inflator for the object to be inflated.
3. Insert the adapter into the object’s
receptacle and press the lever down.
Note: Monitor the Air Pressure Gauge on the
front of the unit to avoid over-inflation.
5. When the proper inflation level has been
reached, press the Air Compressor Switch off.
Safety
4. Press the Air Compressor Switch on.
6. Lift the lever and remove the hose.
WARNING! Do not overinflate any object.
Figure E
1. Press the Battery Test Button to verify that the
Power Pack is fully charged. Recharge as
needed, following the instructions in the “Charging
the Power Pack” section on page 6.
3. Make sure that the Clamp Power
Switch and appliance are off.
2. Make sure the total wattage of the appliance is
within the range of the Power Pack. See “DC
Appliance Compatibility” on page 7.
5. Turn on the appliance.
SETUP
Running/Charging DC Appliances
4. Plug the appliance into the 12VDC Outlet.
6. When finished using, turn off and
unplug the appliance.
2. Plug the device into the USB Port.
3. When finished, unplug the device from the USB Port.
Maintenance
1. Press the Battery Test button to verify that
the Power Pack is fully charged. Recharge
as needed, following the instructions in the
“Charging the Power Pack” section on page 6.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually
as replacement parts. Internal parts are not user-serviceable and are not available.
Item 62374
For technical questions, please call 1-888-866-5797.
Operation
Running/Charging USB Devices
Page 9
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
Safety
TO PREVENT SERIOUS INJURY: Unplug the Power Pack, turn the Clamp Power Switch off and allow
Power Pack to cool completely before performing any inspection, maintenance, or cleaning procedures.
1. BEFORE EACH USE, inspect the general
condition of the Power Pack. Check for:
• loose hardware,
2. Keep unit clean and clamps free
of dirt, debris, or grease.
3. For longer working life, protect Power
Pack from sunlight and moisture.
• cracked or broken parts,
• damaged electrical wiring or cable insulation, and
• any other condition that may
affect its safe operation.
4. AFTER USE, wipe external surfaces of
the Power Pack with clean cloth.
SETUP
5. CONTAINS NON-SPILLABLE, SEALED LEADACID BATTERY. BATTERY MUST BE RECYCLED.
Battery Replacement and Disposal
LEAD BATTERY MUST BE RECYCLED.
WARNING! To prevent damage or injury, replacement battery must be identical to original.
Replace the Battery when the red light comes on while
pressing the Battery Test button after recharging.
1. Remove all screws from the back of
the case and lift off the panel.
2. Lift out the Battery without damaging the circuit board.
Operation
Note: Notice how the red and black cables connect
to the old battery and make sure to keep them in
place, connecting them to the new battery.
4. Position the replacement battery with the label
facing out, and make sure the red (+) recharging
wire and Battery Cable is attached to the
positive (+) battery terminal. Connect both of
the recharging wires and Battery Cables.
5. Carefully slide the Battery into the compartment
without damaging the circuit board.
6. Replace the back panel and the screws.
Call 1‑800‑822‑8837 for battery recycling.
3. Detach the recharging wires and Battery
Cables from the battery terminals.
Maintenance
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 10
For technical questions, please call 1-888-866-5797.
Item 62374
Parts List and Diagram
1
2
3
4
5
6
7
8
9
10
11
12
13
Description
12V DC Outlet Cover
Power Switch Cap
Negative 12VDC Outlet
Power Switch
Positive 12VDC Outlet
Middle Case
Lens
LED Board
Battery
LED Lamp Panel
Positive Battery Cable (Red)
Handle
Back Case
Qty
Part
1
15
16
17
18
19
20
21
22
23
24
25
26
2
1
2
1
2
1
1
1
1
1
1
1
14
Description
Air Hose Compartment
Air Compressor Switch
Compressor Meter Fixture
Compressor Hoop
Internal Adaptor (120VAC)
Adaptor Stator
Compressor
Negative Battery Cable (Black)
Main Circuit Board
USB Cap
Front Case
Internal Connection Wire
AC Power Cable
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
SETUP
Part
Safety
Parts List
Maintenance
Operation
Assembly Diagram
Item 62374
For technical questions, please call 1-888-866-5797.
Page 11
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797