Harbor Freight Tools 6.5 HP Plate Compactor Product manual

Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Using an engine indoors
CAN KILL YOU IN MINUTES.
Engine exhaust contains carbon monoxide.
This is a poison you cannot see or smell.
NEVER use inside
a home or garage,
EVEN IF doors and
windows are open.
REV 14l
Only use OUTSIDE
and far away from
windows, doors,
and vents.
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
or engine technical support at: predator@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2012 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety
Safetye��������������������������������������������������������� 2
Specifications.............................................. 6
Setup........................................................... 6
Operationa���������������������������������������������������� 8
Maintenancei���������������������������������������������� 12
Parts Lists and Diagrams........................... 18
Warranties.................................................. 22
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Setup
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Operation
IMPORTANT SAFETY INFORMATION
Read all instructions.
Failure to follow all instructions listed below may result in fire, serious injury, and/or DEATH.
The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Setup Precautions
Maintenance
1. Gasoline fuel and fumes are flammable
and potentially explosive. Use proper fuel
storage and handling procedures. Do not store
fuel or other flammable materials nearby.
2. Have multiple ABC class fire
extinguishers nearby.
3. Operation of this equipment may create sparks
that can start fires around dry vegetation.
A spark arrestor may be required. The operator
should contact local fire agencies for laws or
regulations relating to fire prevention requirements.
Page 2
4. Set up and use only on a flat, level,
well-ventilated surface.
5. Wear ANSI-approved safety goggles,
heavy-duty work gloves, and dust
mask/respirator during set up.
6. Use only lubricants and fuel recommended
in the engine manual or in the
Specifications chart of this manual.
For technical questions, please call 1-888-866-5797.
ITEM 69738
Operation Precautions
11. Park the Vibrator Plate on a
firm and level surface.
Safety
12. Industrial applications must
follow OSHA requirements.
13. Do not leave the equipment unattended
when it is running. Turn off the
equipment (and remove safety keys, if
available) before leaving the work area.
15. People with pacemakers should consult their
physician(s) before use. Electromagnetic
fields in close proximity to a heart pacemaker
could cause pacemaker interference or
pacemaker failure. Caution is necessary when
near the engine’s magneto or recoil starter.
2. Keep children away from the equipment,
especially while it is operating.
16. Use only accessories that are recommended
by Harbor Freight Tools for your model.
Accessories that may be suitable for one
piece of equipment may become hazardous
when used on another piece of equipment.
3. Keep hands and feet away from the Compactor
Base (53). Grip the Upper Handle (32) of
the Vibrator Plate firmly with both hands.
Never place tools under the Vibrator Plate.
17. Do not operate in explosive atmospheres,
such as in the presence of flammable
liquids, gases, or dust. Gasoline-powered
engines may ignite the dust or fumes.
4. Keep all spectators at least six feet from
the Vibrator Plate during operation.
18. Stay alert, watch what you are doing
and use common sense when operating
this piece of equipment. Do not use this
piece of equipment while tired or under the
influence of drugs, alcohol or medication.
Only use OUTSIDE and far away from windows,
doors, and vents.
5. Only use a suitable means of transport and
lifting devices with sufficient weight bearing
capacity when transporting the Vibrator Plate.
6. Only use sturdy loading ramps with sufficient
weight bearing capacity. Secure the Vibrator
Plate on transport vehicles to prevent the
tool from rolling, slipping, and tilting.
7. Keep a safe distance away from the edges
and banks of ditches and use care to prevent
the Vibrator Plate from toppling over.
8. Ascend slopes carefully in a direct path.
9. Pull backwards up steep slopes
to prevent the Vibrator Plate from
toppling over onto the operator.
10. When performing compacting work in the
vicinity of buildings or above pipelines, make
sure to check the affect of the vibrations on
the buildings and pipelines. If necessary,
immediately stop the compacting work.
ITEM 69738
19. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the equipment in unexpected situations.
Setup
NEVER use inside a home or garage,
EVEN IF doors and windows are open.
14. Wear ANSI-approved safety glasses,
hearing protection, and NIOSH-approved
dust mask/respirator under a full face shield
along with steel-toed work boots during use.
Operation
CARBON MONOXIDE HAZARD
Using an engine indoors CAN KILL
YOU IN MINUTES.
Engine exhaust contains carbon
monoxide. This is a poison you cannot see or smell.
20. Use this equipment with both hands only.
Using equipment with only one hand
can easily result in loss of control.
21. Dress properly. Do not wear loose clothing or
jewelry. Keep hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
22. Parts, especially exhaust system components,
get very hot during use. Stay clear of hot parts.
23. Do not cover the engine or
equipment during operation.
24. Keep the equipment, engine, and
surrounding area clean at all times.
For technical questions, please call 1-888-866-5797.
Page 3
Maintenance
1.
Operation Precautions (cont.)
Safety
25. Use the equipment, accessories, etc., in
accordance with these instructions and in the
manner intended for the particular type of
equipment, taking into account the working
conditions and the work to be performed. Use of
the equipment for operations different from those
intended could result in a hazardous situation.
26. Do not operate the equipment with known
leaks in the engine’s fuel system.
27. This product contains or, when used,
produces a chemical known to the State of
California to cause cancer and birth defects
or other reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
Setup
28. When spills of fuel or oil occur, they must
be cleaned up immediately. Dispose of fluids
and cleaning materials as per any local, state, or
federal codes and regulations. Store oil rags in
a bottom-ventilated, covered, metal container.
29. Keep hands and feet away from moving parts.
Do not reach over or across
equipment while operating.
Vibration Hazard:
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders. To
reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check‑ups
to ensure medical problems are not being
caused or worsened from use. Pregnant women
or people who have impaired blood circulation to the
hand, past hand injuries, nervous system disorders,
diabetes, or Raynaud’s Disease should not use this
tool. If you feel any symptoms related to vibration
(such as tingling, numbness, and white or blue
fingers), seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
Operation
30. Before use, check for misalignment or
binding of moving parts, breakage of
parts, and any other condition that may
affect the equipment’s operation. If
damaged, have the equipment serviced
before using. Many accidents are caused
by poorly maintained equipment.
4. Use tools with the lowest vibration when there
is a choice between different processes.
31. Use the correct equipment for the application.
Do not modify the equipment and do not use the
equipment for a purpose for which it is not intended.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible
(while still keeping safe control of
it). Let the tool do the work.
Maintenance
Page 4
For technical questions, please call 1-888-866-5797.
ITEM 69738
a. Turn the engine switch to its “OFF” position.
b. Allow the engine to completely cool.
c. Then, remove the spark plug wire(s)
from the spark plug(s).
2. Keep all safety guards in place and in
proper working order. Safety guards include
muffler, air cleaner, mechanical guards,
and heat shields, among other guards.
3. Do not alter or adjust any part of the
equipment or its engine that is sealed by the
manufacturer or distributor. Only a qualified
service technician may adjust parts that may
increase or decrease governed engine speed.
4. Wear ANSI-approved safety goggles,
heavy-duty work gloves, and dust
mask/respirator during service.
5. Maintain labels and nameplates on
the equipment. These carry important
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
6. Have the equipment serviced by a
qualified repair person using only identical
replacement parts. This will ensure that
the safety of the equipment is maintained.
Do not attempt any service or maintenance
procedures not explained in this manual or
any procedures that you are uncertain about
your ability to perform safely or correctly.
7. Store equipment out of the reach of children.
8. Follow scheduled engine and
equipment maintenance.
Refueling:
1. Do not smoke, or allow sparks, flames,
or other sources of ignition around the
equipment, especially when refueling.
2. Do not refill the fuel tank while the
engine is running or hot.
3. Do not fill fuel tank to the top.
Leave a little room for the fuel to expand as needed.
Setup
1. Before service, maintenance, or cleaning:
Safety
Maintenance Precautions
4. Refuel in a well-ventilated area only.
Maintenance
Operation
SAVE THESE INSTRUCTIONS.
ITEM 69738
For technical questions, please call 1-888-866-5797.
Page 5
Specifications
Safety
Operating Speed
Engine Type
Plate Size
Weight
0-82 FPM
179cc
16-1/2″ x 22″
176 lbs.
Note: Additional specifications found in the TECHNICAL ENGINE SPECIFICATIONS chart in this manual.
The emission control system for this Vibrator’s
Engine is warranted for standards set by the U.S.
Environmental Protection Agency. For warranty
information, refer to the last pages of this manual.
At high altitudes, the engine’s carburetor,
governor (if so equipped), and any other parts that
control the fuel-air ratio will need to be adjusted by
a qualified mechanic to allow efficient high‑altitude
use and to prevent damage to the engine and
any other devices used with this product.
Setup
Setup
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the equipment off, wait for the engine to cool, and unplug the
spark plug wire(s) before assembling or making any adjustments to the tool.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL FIRES:
Operate only with proper spark arrestor installed. Operation of this equipment may create sparks
that can start fires around dry vegetation. A spark arrestor may be required. The operator should
contact local fire agencies for laws or regulations relating to fire prevention requirements.
Operation
Note: For additional information regarding the parts listed in the following pages,
refer to Parts Lists and Diagrams on page 18.
Handle Setup
1. Loosen the Knob Handle (31) on each
side of the Upper Handle (32).
Knob
Handles (31)
2. Swing the Upper Handle until it points
straight out from the Lower Handle (29).
3. Tighten both Knob Handles (31) securely.
Maintenance
Upper
Handle (32)
Lower
Handle (29)
Page 6
For technical questions, please call 1-888-866-5797.
ITEM 69738
Engine Controls
Fuel Cap
Safety
Air Filter
Muffler
Setup
Starter
Handle
Oil Drain Plug
Dipstick
Operation
Engine
Switch
Choke
Fuel Valve
Serial
Number
Location
Maintenance
(Write on front
cover of manual.)
Speed
Control
Lever
ITEM 69738
For technical questions, please call 1-888-866-5797.
Page 7
Operation
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
Safety
Pre-Start Checks
1. Inspect engine and equipment looking for
damaged, loose, and missing parts before set
up and starting. If any problems are found,
do not use equipment until fixed properly.
2. IMPORTANT: CHECK HARDWARE
TIGHTNESS BEFORE EVERY USE. The
strong vibrations created during use will
cause some hardware to loosen.
3. Firmly attach the Upper Handle (32) BEFORE use.
Setup
Checking and Filling Engine Oil
NOTICE: Your Warranty is VOID if the engine’s
crankcase is not properly filled with oil before
each use. Before each use, check the oil level.
Do not run the engine with low or no engine oil.
Running the engine with no or low engine oil
WILL permanently damage the engine.
1. Make sure the engine is stopped and is level.
2. Close the Fuel Valve.
Checking and Filling Fuel
WARNING! TO PREVENT SERIOUS
INJURY FROM FIRE:
Fill the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before adding fuel. Do not smoke.
1. Clean the Fuel Cap and the area around it.
2. Unscrew and remove the Fuel Cap.
Note: Do not use gasoline containing
more than 10% ethanol (E10). Do not use
E85 ethanol. Add fuel stabilizer to the
gasoline or the Warranty is VOID.
Note: Do not use gasoline that has been stored in a
metal fuel container or a dirty fuel container. It can
cause particles to enter the carburetor, affecting
engine performance and/or causing damage.
Operation
3. If needed, fill the Fuel Tank to about 1 inch under
the fill neck of the Fuel Tank with 87 octane or
higher unleaded gasoline that has been treated
with a fuel stabilizer additive. Follow fuel stabilizer
manufacturer’s recommendations for use.
3. Clean the top of the Dipstick and the
area around it. Remove the Dipstick
by threading it counterclockwise, and
wipe it off with a clean lint free rag.
4. Then replace the Fuel Cap.
Full level
Full level
5. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
4. Reinsert the Dipstick without threading it in and
remove it to check the oil level. The oil level
should be up to the full level as shown above.
Maintenance
5. If the oil level is at or below the low mark add the
appropriate type of oil until the oil level is at the
proper level. SAE 10W‑30 oil is recommended
for general use. (The SAE Viscosity Grade chart
on page 13 in the Service section shows other
viscosities to use in different average temperatures.)
6. Thread the dipstick back in clockwise.
CAUTION! Do not run the engine with too little oil.
The engine will be permanently damaged.
Page 8
For technical questions, please call 1-888-866-5797.
ITEM 69738
Starting the Engine
Before Starting the Engine
1. To start a cold engine, move the Choke to the
CHOKE position.
To restart a warm engine, leave the
Choke in the RUN position.
Safety
Before starting the engine:
a. Follow the Set Up Instructions in the equipment manual to prepare the equipment.
b. Inspect the equipment and engine.
c. Fill the engine with the proper amount and type of both fuel and oil.
d. Read the Equipment Operation section in the equipment manual.
Setup
1
2. Open the Fuel Valve.
3
Speed
Control
Lever
O
4. Turn the Engine Switch on.
ITEM 69738
OFF
ON
ON
I
Maintenance
3. Slide the Speed Control Lever (54) to
1/3 away from the SLOW position.
Operation
2
4
For technical questions, please call 1-888-866-5797.
Page 9
5. Grip the Starter Handle of the Engine loosely and pull
it slowly several times to allow the gasoline to flow into
the Engine’s carburetor. Then pull the Starter Handle
gently until resistance is felt. Allow Cable to retract fully
and then pull it quickly. Repeat until the engine starts.
5
Safety
Note: Do not let the Starter Handle snap back against
the engine. Hold it as it recoils so it doesn't hit the engine.
6. Allow the Engine to run for several seconds.
Then, if the Choke lever is in the CHOKE position,
move the Choke Lever very slowly to its RUN position.
6
NOTE: Moving the Choke Lever too fast could stall the engine.
Setup
IMPORTANT: Allow the engine to run at no load for five minutes with
no load after each start‑up so that the engine can stabilize.
7. Grip the Upper Handle (32) firmly with both hands.
8. Depending on the desired speed at which the Vibrator Plate will
vibrate, adjust the Speed Control Lever (54) between its “LOW” to
“HIGH” position.
8
Speed
Control
Lever
9. Slowly push or pull the Vibrator Plate while
guiding the tool in the desired direction.
10. Keep a safe distance away from the edges and banks of ditches and
use care to prevent the Vibrator Plate from toppling over.
Operation
11. Ascend slopes carefully in a direct path. Pull backwards up steep slopes to
prevent the Vibrator Plate from toppling over onto the operator.
12. Break-in Period:
a. Breaking-in the engine will help to ensure proper equipment and engine operation.
b. The operational break-in period will last about 3 hours of use.
Do not operate the engine at its maximum speed during this period.
c. The maintenance break-in period will last about 20 hours of use. Change the engine oil after this period.
Under normal operating conditions subsequent maintenance follows the schedule
explained in the MAINTENANCE AND SERVICING section.
Maintenance
Page 10
For technical questions, please call 1-888-866-5797.
ITEM 69738
Stopping the Engine
I
Safety
OFF
To stop the engine in an emergency,
turn the Engine Switch off.
O
Under normal conditions, use the following procedure:
2
2. Turn the Engine Switch off.
3. Close the Fuel Valve.
OFF
O
Setup
1
I
Operation
1. Slide the Speed Control Lever (54) to SLOW.
Speed
Control
Lever
3
4. Park the Vibrator Plate on a firm and level surface after use.
Maintenance
5. The Knob Handles (31) can be loosened and the
Upper Handle (32) folded down to aid in storage.
NOTICE
See Long-Term Storage on page 15
for complete storage instructions.
ITEM 69738
For technical questions, please call 1-888-866-5797.
Page 11
Maintenance
Technical Specifications
Safety
Engine Type
Bore x Stroke
Displacement
Compression Ratio
Rotation viewed from PTO
(power takeoff - the output shaft)
Fuel
Type
Capacity
Single Cylinder 4
stroke OHV
65mm x 54mm
179cc
8.5:1
Engine Oil
Counterclockwise
87+ octane stabilizertreated unleaded gasoline
1 Gallon
Type SAE
Capacity
Type
Spark Plug
Gap
Intake
Valve
Clearance Exhaust
Speed
Idle
10W-30 above 32° F
5W-30 at 32° F or below
0.5 Quarts
Torch & LG
0.028 - 0.031″
0.10 - 0.15 mm
0.15 - 0.20 mm
1,800 ±50 RPM
WARNING
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING:
Turn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool, and disconnect
the spark plug cap before performing any inspection, maintenance, or cleaning procedures.
Setup
TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE:
Do not use damaged equipment. If abnormal noise, vibration, or excess
smoking occurs, have the problem corrected before further use.
Follow all service instructions in this manual. The engine may fail critically if not serviced properly.
Many maintenance procedures, including any not detailed in this manual, will need to be performed
by a qualified technician for safety. If you have any doubts about your ability to safely service the
equipment or engine, have a qualified technician service the equipment instead.
Maintenance and Lubrication Schedule
Operation
Note: This maintenance schedule is a general guide only. If performance decreases or if equipment
operates unusually, check systems immediately. The maintenance needs of each engine will differ
depending on factors such as duty cycle, temperature, air quality, fuel quality, and other factors.
Note: The following procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the engine and equipment.
Procedure
1. Brush off outside of engine
Before
Each Use
Every 2 weeks
or 10 hr. of use
Monthly or
20 hr. of use
Every 6 mo. or
100 hr. of use
Yearly or
300 hr. of use
Every
2 Years
2. Check and tighten
all hardware
3. Check engine oil level
and deposit cup
Clean/replace air cleaner
Change engine oil
*
Maintenance
Check and clean spark plug
1. Check/adjust idle speed
and valve clearance
2. Clean fuel tank, strainer
and carburetor
**
3. Clean carbon build-up from
combustion chamber
Check/replace fuel line
*Service more frequently when used in dusty areas.
Page 12
**These items should be serviced
**
**
by a qualified technician.
For technical questions, please call 1-888-866-5797.
ITEM 69738
Engine Oil Change
WARNING! TO PREVENT SERIOUS
INJURY FROM FIRE:
Fill the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before adding fuel. Do not smoke.
CAUTION! Oil is very hot during
operation and can cause burns. Wait for
engine to cool before changing oil.
2. Unscrew and remove the Fuel Cap.
Note: Do not use gasoline containing
more than 10% ethanol (E10). Do not use
E85 ethanol. Add fuel stabilizer to the
gasoline or the Warranty is VOID.
Note: Do not use gasoline that has been stored in a
metal fuel container or a dirty fuel container. It can
cause particles to enter the carburetor, affecting
engine performance and/or causing damage.
3. If needed, fill the Fuel Tank to about 1 inch under
the fill neck of the Fuel Tank with 87 octane or
higher unleaded gasoline that has been treated
with a fuel stabilizer additive. Follow fuel stabilizer
manufacturer’s recommendations for use.
2. Close the Fuel Valve.
3. Place a drain pan (not included) underneath
the crankcase’s drain plug.
4. Remove the drain plug and, if possible, tilt the
crankcase slightly to help drain the oil out.
Recycle used oil.
5. Replace the drain plug and tighten it.
6. Clean the top of the Dipstick and the
area around it. Remove the Dipstick
by threading it counterclockwise, and
wipe it off with a clean lint free rag.
Full level
Full level
Setup
1. Clean the Fuel Cap and the area around it.
1. Make sure the engine is stopped and is level.
Safety
Checking and Filling Fuel
4. Then replace the Fuel Cap.
5. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
7. Add the appropriate type of oil until the oil level is at
the full level. SAE 10W‑30 oil is recommended for
general use.
The SAE Viscosity Grade chart shows other
viscosities to use in different average temperatures.
Operation
SAE Viscosity Grades
30
10W-30
5W-30
-20
0
20
40
60
80
Average outdoor temperature
100°F
CAUTION! Do not run the engine with too little oil.
The engine will be permanently damaged.
ITEM 69738
For technical questions, please call 1-888-866-5797.
Page 13
Maintenance
8. Thread the dipstick back in clockwise.
Air Filter Element Maintenance
1. Remove the Air Cleaner Cover and the air filter(s)
and check for dirt. Clean as described below.
2. Cleaning:
Safety
• For paper filters:
To prevent injury from dust and debris,
wear ANSI-approved safety goggles,
NIOSH‑approved dust mask/respirator, and
heavy-duty work gloves. In a well‑ventilated
area away from bystanders, use pressurized
air to blow dust out of the filter.
• For foam filters:
Wash the filter in warm water and mild
detergent several times. Rinse. Squeeze out
excess water and allow it to dry completely.
Soak the filter in lightweight oil briefly,
then squeeze out the excess oil.
3. Install the cleaned filter(s). Secure the
Air Cleaner Cover before use.
Spark Plug Maintenance
Spark
Plug
Cap
1. Disconnect spark plug cap from end of plug.
Clean out debris from around spark plug.
2. Using a spark plug wrench, remove the spark plug.
Setup
3. Inspect the spark plug:
If the electrode is oily, clean it using a clean, dry
rag. If the electrode has deposits on it, polish it
using emery paper. If the white insulator is cracked
or chipped, the spark plug needs to be replaced.
NOTICE: Use only the spark plug listed on
the Technical Specifications chart. Using an
incorrect spark plug may damage the engine.
4. When installing a new spark plug, adjust the
plug’s gap to the specification on the Technical
Specifications chart. Do not pry against the
electrode, the spark plug can be damaged.
Operation
5. Install the new spark plug or the cleaned spark plug
into the engine. Gasket-style: Finger-tighten until
the gasket contacts the cylinder head, then tighten
about 1/2-2/3 turn more.
Non-gasket-style: Finger-tighten until
the plug contacts the head, then
tighten about 1/16 turn more.
NOTICE: Tighten the spark plug properly.
If loose, the spark plug will cause the engine
to overheat. If overtightened, the threads
in the engine block will be damaged.
6. Apply dielectric spark plug boot protector
(not included) to the end of the spark
plug and reattach the wire securely.
Maintenance
Page 14
For technical questions, please call 1-888-866-5797.
ITEM 69738
Belt Tension Adjustment
Safety
4. Tighten the four Nuts (21) that hold the
Engine (16) to the Connecting Plates (23).
Belt Replacement
1. Turn off engine.
2. Loosen, but do not remove, the four Nuts (21) that
hold the Engine (16) to the Connecting Plates (23).
3. Using Nut (43) and Bolt (42), slide the
Engine (16) towards the Driver Pulley (47)
until Belts (20) can be removed.
4. Remove the old Belts, then install new ones.
5. Check the alignment of the two pulleys
(side by side - in the same level/surface).
6. Using Nut (43) and Bolt (42), slide
Engine (16) away from Driver Pulley (47)
until Belt is properly tensioned.
7. Re-tighten the four Nuts (21) that hold the
Engine (16) to the Connecting Plates (23).
Long-Term Storage
When the equipment is to remain idle for longer than
20 days, prepare the engine for storage as follows:
c. Replace spark plug, but leave
spark plug cap disconnected.
1. CLEANING:
Wait for engine to cool, then clean engine with
dry cloth. NOTICE: Do not clean using water.
The water will gradually enter the engine
and cause rust damage.
Apply a thin coat of rust preventive
oil to all metal parts.
d. Pull Starter Handle to distribute oil in cylinder.
Stop after one or two revolutions when you
feel the piston start the compression stroke
(when you start to feel resistance).
To protect the fuel tank during storage, fill the
tank with gasoline that has been treated with
a fuel stabilizer additive. Follow fuel stabilizer
manufacturer’s recommendations for use. Refer
to Checking and Filling Fuel on page 8.
WARNING! TO PREVENT SERIOUS
INJURY FROM FIRE:
Fill tank in a well-ventilated area away from
ignition sources. If the engine is hot from
use, shut the engine off and wait for it to
cool before adding fuel. Do not smoke.
3. LUBRICATION:
a. Change engine oil.
b. Clean out area around spark plug.
Remove spark plug and pour one tablespoon of
engine oil into cylinder through spark plug hole.
ITEM 69738
4. BATTERY:
Disconnect battery cables (if equipped).
Recharge batteries monthly while in storage.
5. STORAGE AREA:
Cover and store in a dry, level, well-ventilated
area out of reach of children. Storage area should
also be away from ignition sources, such as
water heaters, clothes dryers, and furnaces.
NOTICE: During extended storage periods the
Engine must be started every 3 months and allowed
to run for 15 – 20 minutes or the Warranty is VOID.
6. AFTER STORAGE:
Before starting the engine after storage, keep in
mind that untreated gasoline will deteriorate quickly.
Drain the fuel tank and change to fresh fuel if
untreated gasoline has been sitting for a month,
if treated gasoline has been sitting beyond
the fuel stabilizer’s recommended time
period, or if the engine does not start.
For technical questions, please call 1-888-866-5797.
Maintenance
2. FUEL:
Setup
2. Loosen, but do not remove, the four Nuts (21) that
hold the Engine (16) to the Connecting Plates (23).
3. Slide the Engine (16), away from the Driver
Pulley (47), until the belts are properly tensioned.
Operation
1. Turn off engine.
Page 15
Troubleshooting
Possible Causes
Probable Solutions
Engine will not start
FUEL RELATED:
1. No fuel in tank or fuel valve closed.
2. Choke not in CHOKE position, cold engine.
3. Gasoline with more than 10% ethanol
used. (E15, E20, E85, etc.)
9. Clogged Fuel Filter.
FUEL RELATED:
1. Fill fuel tank and open fuel valve.
2. Move Choke to CHOKE position.
3. Clean out ethanol rich gasoline from fuel
system. Replace components damaged
by ethanol. Use fresh 87+ octane
unleaded gasoline only.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
4. Use fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
5. Pull on Starter Handle to prime.
6. Clean out passageways using
fuel additive. Heavy deposits
may require further cleaning.
7. Gently tap side of carburetor float
chamber with screwdriver handle.
8. Turn Choke to RUN position.
Remove spark plug and pull the start
handle several times to air out the
chamber. Reinstall spark plug and
set Choke to CHOKE position.
9. Replace Fuel Filter.
IGNITION (SPARK) RELATED:
1. Spark plug cap not connected securely.
2. Spark plug electrode wet or dirty.
3. Incorrect spark plug gap.
4. Spark plug cap broken.
5. Circuit breaker tripped
(electric start models only).
6. Incorrect spark timing or
faulty ignition system.
IGNITION (SPARK) RELATED:
1. Connect spark plug cap properly.
2. Clean spark plug.
3. Correct spark plug gap.
4. Replace spark plug cap.
5. Reset circuit breaker. Check wiring and
starter motor if breaker continues to trip.
6. Have qualified technician diagnose/
repair ignition system.
COMPRESSION RELATED:
1. Cylinder not lubricated.
Problem after long storage periods.
COMPRESSION RELATED:
1. Pour tablespoon of oil into spark plug
hole.
Crank engine a few times
and try to start again.
2. Tighten spark plug. If that does
not work, replace spark plug. If
problem persists, may have head
gasket problem, see #3.
3. Tighten head. If that does not remedy
problem, replace head gasket.
Safety
Problem
4. Low quality or deteriorated, old gasoline.
5. Carburetor not primed.
6. Dirty fuel passageways.
Setup
7. Carburetor needle stuck.
Fuel can be smelled in the air.
8. Too much fuel in chamber. This can be
caused by the carburetor needle sticking.
Operation
2. Loose or broken spark plug. (Hissing
noise will occur when trying to start.)
Maintenance
3. Loose cylinder head or
damaged head gasket. (Hissing noise
will occur when trying to start.)
4. Engine valves or tappets
mis‑adjusted or stuck.
4. Have qualified technician diagnose/
repair ignition system.
Follow all safety precautions whenever diagnosing or servicing the equipment or engine.
Page 16
For technical questions, please call 1-888-866-5797.
ITEM 69738
Troubleshooting (cont’d)
Engine stops when
under heavy load
1. Dirty air filter
2. Engine running cold.
1. Clean element.
2. Allow engine to warm up prior
to operating equipment.
Engine misfires
1. Spark plug cap loose.
2. Incorrect spark plug gap or
damaged spark plug.
3. Defective spark plug cap.
4. Old or low quality gasoline.
1. Check wire connections.
2. Re-gap or replace spark plug.
Engine stops
suddenly
1. Low oil shutdown.
2. Fuel tank empty or full of impure or low
quality gasoline.
3. Defective fuel tank cap creating
vacuum, preventing proper fuel flow.
4. Faulty magneto.
5. Disconnected or improperly
connected spark plug cap.
Engine knocks
1. Old or low quality gasoline.
2. Engine overloaded.
3. Incorrect spark timing, deposit
buildup, worn engine, or other
mechanical problems.
Engine backfires
1. Impure or low quality gasoline.
2. Engine too cold.
3. Intake valve stuck or overheated engine.
4. Incorrect timing.
Equipment does
not operate with
engine running
1. Engine idling.
2. Broken or loose belt.
3. Replace spark plug cap.
4. Use only fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
5. Diagnose and repair compression.
(Use Engine will not start:
COMPRESSION RELATED section.)
1. Fill engine oil to proper level. Check
engine oil before EVERY use.
2. Fill fuel tank with fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
3. Test/replace fuel tank cap.
4. Have qualified technician
service magneto.
5. Secure spark plug cap.
1. Fill fuel tank with fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
2. Do not exceed equipment’s load rating.
3. Have qualified technician
diagnose and service engine.
1. Fill fuel tank with fresh 87+ octane
unleaded gasoline.
Do not use gasoline with more than
10% ethanol (E15, E20, E85, etc.).
2. Use cold weather fuel and oil
additives to prevent backfiring.
3. Have qualified technician
diagnose and service engine.
4. Check engine timing.
1. This is normal operation.
Increase engine speed
to start operation.
2. Inspect belt and replace if broken or
worn.
Tension belt properly.
Follow all safety precautions whenever diagnosing or servicing the equipment or engine.
ITEM 69738
Setup
5. Incorrect compression.
Safety
Probable Solutions
For technical questions, please call 1-888-866-5797.
Page 17
Operation
Possible Causes
Maintenance
Problem
Parts Lists and Diagrams
PLEASE READ THE FOLLOWING CAREFULLY
Safety
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Main Parts List
Part
Setup
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
Operation
16
Shaft Circlip
Hole Circlip
Ball Bearing (6006)
Drive Pulley
Cover
Friction Block
Spring
Flap Wheel
Flat Washer (Ø8)
Spring Washer (Ø8)
Bolt
Bolt (M10x20)
Spring Washer (Ø10)
Flat Washer (Ø10)
Pulley Cover
179cc Engine
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Screw (M4x10)
Throttle Hoop
Flat Key (M5x30)
Cone Belt
Nut (M8)
Flat Washer (Ø8)
Connecting Plate
Single Threaded Rubber Shaft
Nut (M10)
Bolt (M12x16)
Rubber Sleeve
Screw
Lower Handle
Circular Stem
(details in Parts List and Diagram A)
Qty
1
1
2
1
1
6
1
1
1
17
1
4
6
6
1
1
1
1
1
2
4
16
2
2
2
2
2
3
1
2
Part
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Description
Knob Handle
Upper Handle
Bolt (M10x60)
Rivet (M8x50)
Flat Washer (Ø12)
Self-Locking Nut (M12)
Engine Pull Spring
Bolt (M8x25)
Grease Port
Bearing Cover (1)
Bearing (6308)
Bolt (M10x60)
Nut (M10)
Oil Seal
Bearing Cover (2)
Base Cover
Driver Pulley
Stopper Plate
Spring Washer (Ø12)
Bolt (M12x25)
Double Threaded Rubber Shaft
Flat Washer (Ø12)
Compactor Base
Speed Control Lever
Nut (M5)
Flexible Shaft
Inner Hex Screw (M12x4)
Bearing Housing
Eccentric Shaft
Flat Key (M10x30)
Qty
2
1
2
2
13
10
1
12
2
1
2
1
1
1
1
1
1
1
15
1
4
4
1
1
1
1
6
1
1
1
Maintenance
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 18
For technical questions, please call 1-888-866-5797.
ITEM 69738
Maintenance
Operation
Setup
Safety
Main Assembly Diagram
ITEM 69738
For technical questions, please call 1-888-866-5797.
Page 19
Parts List A - Engine (16)
Part
1A
2A
Safety
3A
4A
5A
6A
7A
8A
9A
10A
11A
12A
13A
Setup
14A
15A
16A
17A
18A
19A
20A
21A
22A
23A
24A
25A
26A
27A
28A
29A
Operation
30A
31A
32A
33A
34A
35A
36A
37A
38A
Description
Gasket, Cylinder Head
Cover Subassembly,
Cylinder Head
Gasket, Cylinder
Head Cover
Tube, Breather
Bolt
Stud
Stud
Stud
Pin
Bolt, Cylinder Head
Plug, Spark
Head Subassembly,
Cylinder
Crankcase
Subassembly.
Sensor, Engine Oil
Gear Assy, Governor
Arm, Governor
Bolt, Drain Plug
Washer
Bearing
Seal, Oil
Washer
Pin
Bolt
Cover, Crankcase
Bearing
Seal, Oil
Gasket, Crankcase
Pin
Dipstick
Subassembly, Oil
Plug Subassembly,
Engine Oil
Bolt
Crankshaft Assy.
Clip, Piston Pin
Piston
Pin, Piston
Rod, Connecting
Ring, The First
Ring, The Second
Qty
1
1
1
1
4
1
1
2
2
4
1
1
1
1
1
1
2
2
1
1
1
1
2
1
1
1
1
2
1
1
6
1
2
1
1
1
1
1
Part
39A
40A
41A
42A
43A
44A
45A
46A
47A
48A
49A
50A
51A
52A
53A
54A
55A
56A
57A
58A
59A
60A
61A
62A
63A
64A
65A
66A
67A
68A
69A
70A
71A
72A
73A
74A
75A
76A
77A
78A
Description
Ring Set, Oil
Camshaft Assy.
Valve, Exhaust
Valve, Intake
Seat, Valve Spring
Retainer, Exhaust Valve
Rotator, Valve
Guide, Seal
Tappet, Valve
Lifter, Valve
Plate Subassembly,
Lifter Stopper
Bolt, Valve Adjusting
Rocker, Valve
Nut, Valve Adjusting
Nut, Valve Lock
Spring, Valve
Starter Assy, Recoil
Bolt
Shroud
Shroud, Cylinder Body
Shield,Lower
Protector, Oil
Switch Subassembly,
Stop Engine
Bolt
Bolt
Collar
Bolt
Bolt
Carburetor Assy.
Gasket, Air Cleaner
Gasket, Carburetor
Plate, Carburetor
Insulator
Gasket, Carburetor
Insulator
Nut
Cleaner, Air
Gasket, Exhaust Outlet
Nut
Muffler Assy.
Bolt
Qty
1
1
1
1
1
1
1
1
1
2
2
1
2
2
2
2
1
3
1
1
1
1
1
2
1
1
1
4
1
1
1
1
1
2
1
1
2
1
2
Part
Description
79A Gasket, The Second
Supply Air Valve Flange
80A Valve, Muffler The
Second Supply Air
81A Tank, Fuel
82A Strainer, Fuel
83A Cover, Fuel Tank
84A Outlet Subassembly,
Fuel Tank Oil
85A Clamp
86A Tube, Fuel
87A Bolt
88A Nut
89A
90A Hose, Fuel Steam
Rubber
91A
92A Collector, Fuel Steam
93A Clamp
94A Hose, Air Cleaner
Rubber
95A Nut, Flywheel
96A Pulley,Starter
97A Impeller
98A Flywheel Subassembly
99A Bolt
100A Coil, Ignition
101A Control Assy, Throttle
102A Bolt
103A Spring, Governor
104A Rod, Governor
105A Spring, Throttle
Valve Returning
106A Bolt, Governor Support
107A Nut
108A Support Subassembly,
Governor
109A Valve, One Way
110A Clamp
111A Cover, Fuel Steam
Collector
112A Bolt
113A Jacket, Rubber
Qty
1
1
1
1
1
1
4
1
1
2
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
2
1
Maintenance
Page 20
For technical questions, please call 1-888-866-5797.
ITEM 69738
Safety
76
78
79
10
11
78
80
8
75
8
77
31
31
31
31
31
33
31
30
37 38 39
1
9
9
26
24
34
35
25
33
53 52
53 52
29
27
42
40
102
28 102
47
47
49
43 5446
44 54 41
48
50
50
45
28
36
51
51
48
Setup
76
3
7
67
32
23
23
14
101
107
105
106
103
104
15
108
19
17
72
18
72
73
16
22
113
87
84
86
21
88
85 94
13
110
85
100
20
8185
98
18
92
90
85
93
99
99
112
88
Operation
2
10
10
10
12
69
68
109
17
83
82
97
111
112
62
62
96
58
95
64
55
65
59
57
63
60
66
61
66
56
66
66
Maintenance
5
4
6
Assembly Diagram A - Engine (16)
5
5
5
71
70
Note: When ordering parts from
this diagram, use the suffix -A.
56
56
Page 21
For technical questions, please call 1-888-866-5797.
ITEM 69738
Warranties
Limited 90 Day Warranty
Safety
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
Setup
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Operation
Maintenance
Page 22
For technical questions, please call 1-888-866-5797.
ITEM 69738
Emission Control System Warranty
Where a warrantable condition exists, HFT will repair your
engine at no cost to you including diagnosis, parts and labor.
Manufacturer’s Warranty Coverage
The 2014-2015 engines are warranted for two (2) years.
If any emission-related part on your engine is defective,
the part will be repaired or replaced by HFT.
Harbor Freight Tools Emission Control
Defects Warranty Coverage
Engines are warranted for a period of two (2) years relative
to emission control parts defects, subject to the provisions
set forth below. If any emission related part on your engine
is defective, the part will be repaired or replaced by HFT.
Owner’s Warranty Responsibilities
• As the engine owner, you are responsible for the performance
of the required maintenance listed in your Owner’s Manual.
HFT recommends that you retain all receipts covering
maintenance on your engine, but HFT cannot deny
warranty solely for the lack of receipts or for your failure to
ensure the performance of all scheduled maintenance.
• As the engine owner, you should, however, be aware
that HFT may deny you warranty coverage if your engine
or a part has failed due to abuse, neglect, improper
maintenance, or unapproved modifications.
• You are responsible for shipping your engine to a HFT warranty
station as soon as a problem exists. Contact the HFT Customer
Service department at the number below to make shipping
arrangements. The warranty repairs should be completed
in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights
and responsibilities, you should contact the Harbor Freight Tools
Customer Service Department at 1-888-866-5797.
Harbor Freight Tools Emission Control
Defects Warranty Provisions
1. Length of Coverage
HFT warrants to a first retail purchaser and each
subsequent purchaser that the engine is free from
defects in materials and workmanship that cause the
failure of warranted parts for a period of two (2) years
after the date of delivery to the first retail purchaser.
2. No Charge Repair or Replacement
Repair or replacement of any warranted part will be
performed at no charge to the owner if the work is
performed through a warranty station authorized by
HFT. For emissions warranty service, contact the HFT
Customer Service Department at 1-888-866-5797.
Component parts which are not scheduled for replacement
as required maintenance or are scheduled only for regular
inspection to the effect of “repair or replace as necessary”
are warranted for the warranty period. Any warranted part
which is scheduled for replacement as required maintenance
is warranted for the period of time up to the first scheduled
replacement point for that part. Any replacement part,
provided it is equivalent in durability and performance, may
be used in performance of maintenance or repairs. The
owner is responsible for commissioning a qualified technician/
mechanic to perform all required maintenance, as outlined in the
Inspection, Cleaning, and Maintenance section in this manual.
6. Warranted Parts
1)
Fuel Metering System
i) Carburetor and its internal parts.
ii) Air/fuel ratio feedback and control system.
iii) Cold start enrichment system.
iv) Fuel Tank.
2) Air Induction System
i) Controlled hot air intake system.
ii) Intake manifold.
iii) Air filter.
3) Ignition System
i) Spark Plugs.
ii) Magneto or electronic ignition system.
iii) Spark advance/retard system.
4) Exhaust Gas Recirculation (EGR) System (if so equipped)
i) EGR valve body, and carburetor spacer.
ii) EGR rate feedback and control system.
5) Air Injection System
i) Air pump or pulse valve.
ii) Valves affecting distribution of flow.
iii) Distribution manifold.
6) Catalyst or Thermal Reactor System (if so equipped)
i) Catalytic converter.
ii) Thermal reactor.
iii) Exhaust manifold.
7)Particulate Controls
Traps, filters, precipitators, and any other device used to
capture particulate emissions.
3. Consequential Damages Coverage
Coverage under this warranty shall also extend to the failure
of any engine components caused by the failure of any
warranted part while it is still covered under this warranty.
ITEM 69738
Safety
5. Service and Maintenance
Setup
Your emission control system may include parts
such as the carburetor or fuel-injection system, and
the ignition system. Also included may be hoses, belts,
connectors and other emission-related assemblies.
Warranty claims shall be filed in accordance with the provisions
of the HFT warranty policy explained in the box at the top of the
previous page. HFT shall not be liable for any loss of use of
the engine, for any alternative usage, for any damage to goods,
loss of time, or inconvenience. Warranty coverage shall also be
excluded for any part which fails, malfunctions, or is damaged
due to failure to follow the maintenance and operating instructions
set forth in the Owner’s Manual including, but not limited to:
a) Use of parts which are not authorized by HFT
b) Improper installation, adjustment or repair of the engine or
of any warranted part unless performed by an authorized
warranty center
c) Failure to follow recommendations on fuel use contained in
the Owner’s Manual
d) Improper or inadequate maintenance of any warranted parts
e) Repairs performed outside of the authorized warranty
service dealers
f) Alterations by changing, adding to or removing parts from
the engine.
For technical questions, please call 1-888-866-5797.
Page 23
Operation
The United States Environmental Protection Agency (herein
EPA), and Harbor Freight Tools (herein HFT) are pleased to
explain the emission control system warranty on your 2014-2015
Small Off-Road Engine (herein engine). Within the United States,
new off-road, spark-ignition engines certified for model year
2014-2015, must meet standards set forth by the EPA. HFT
must warrant the emission control system on your engine for
the periods of time described below, provided there has been
no abuse, neglect or improper maintenance of your engine.
4. Coverage Exclusions
Maintenance
United States Emission Control
Defects Warranty Statement
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797