Harbor Freight Tools 65076 User's Manual

24 ton log splitter
65076
Set up, Operating, and Servicing
Instructions
WARNING!
IMPORTANT INFORMATION
The Hitch Coupler MUST be properly
secured to the hitch ball of the towing vehicle.
After assembly and attachment, pull up and
down on the Hitch Coupler to make sure the
hitch ball is fitting snugly in the Hitch Coupler.
There must be no play between the hitch
ball and Hitch Coupler. If there is play, tighten
the Adjustment Nut until no play is present. If
the Adjustment Nut is too tight, the Handle
will not lock. Carefully read and follow
the complete instructions in this manual
BEFORE setup or use.
If the Coupler is not secured
properly, the ball could come loose
while the Log Splitter is in motion,
possibly causing property damage,
serious personal injury, or
death.
Tools®.
Distributed exclusively by Harbor Freight
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Contents
Important SAFETY
Information���������������������������� 3
Basic Specifications������������� 7
Unpacking���������������������������������� 7
Set Up Instructions��������������� 7
Assembly���������������������������������������� 7
Packing the bearings.��������� 7
Hub and Wheel Assembly���� 8
Connecting the Rail
Assembly (2) to the Oil
Tank Assembly (10B)������������ 8
Transportation���������������������� 8
Operating Instructions���� 10
Engine Operation���������������������� 10
Start Procedure����������������� 10
Equipment Operation��������������� 10
Servicing���������������������������������� 12
Maintenance Procedures����� 12
Engine Maintenance and
Service���������������������������������� 12
Equipment Lubrication������ 12
Storage����������������������������������������12
Transportation������������������������� 12
Hydraulic System Care���������� 13
Parts list��������������������������������� 14
ASSEMBLY DIAGRAM���������������� 15
Hydraulic Ram Seals���������� 16
Hydraulics Drawing������������ 17
Limited 1 year / 90 Day
warranty������������������������������ 18
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 2
Save This Manual
NOTICE is used to
address practices
not related to personal injury.
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
WARNING! Read all instructions.
Failure to follow all instructions
listed below may result in fire,
serious injury and/or DEATH.
The warnings and precautions
discussed in this manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into
this product, but must be supplied
by the operator.
Important SAFETY
Information
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
SKU 65076
SAVE THESE INSTRUCTIONS
Set up precautions
1.
Gasoline fuel and fumes are flammable, and potentially explosive. Use
proper fuel storage and handling procedures. Do not store fuel or other
flammable materials nearby.
2.
Have multiple ABC class fire extinguishers nearby.
3.
Operation of this equipment may create sparks that can start fires around
dry vegetation.
A spark arrestor may be required.
The operator should contact local fire
agencies for laws or regulations relating to fire prevention requirements.
4.
Set up and use only on a flat, level,
well-ventilated surface.
For technical questions, please call 1-800-444-3353.
Page 3
5.
Wear ANSI-approved safety goggles,
heavy-duty work gloves, and dust
mask/respirator during set up.
6.
Use only lubricants and fuel recommended in the engine manual or in
the Specifications chart of this manual.
Engine precautions
Follow engine precautions and instructions in the included engine
instruction manual.
3.
Do not leave the equipment unattended when it is running. Turn off
the equipment (and remove safety
keys, if available) before leaving the
work area.
4.
Wear ANSI-approved safety glasses,
hearing protection, and NIOSH-approved dust mask/respirator under a
full face shield during use.
5.
People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to a heart pacemaker could
cause pacemaker interference or
pacemaker failure. Caution is necessary when near the engine’s magneto
or recoil starter.
6.
Use only accessories that are recommended by Harbor Freight Tools for
your model. Accessories that may be
suitable for one piece of equipment
may become hazardous when used
on another piece of equipment.
7.
Operate the Log Splitter, with the
wheels blocked, on a dry, level surface capable of supporting the combined weight of the Log Splitter and
logs.
8.
Do not tow the Log Splitter on roads
or highways. This product is not
D.O.T. compliant, and is not road
legal.
9.
Always make sure the hitch coupler
is securely fixed to the vehicle before
moving it. If the Coupler is not secured properly, the link could come
loose while the trailer is in motion,
possibly causing property damage,
SERIOUS PERSONAL INJURY, or
DEATH.
Operating precautions
1.
Carbon Monoxide
Hazard
Using an engine indoors
CAN KILL YOU IN
MINUTES.
Engine exhaust contains carbon
monoxide. This is a poison you
cannot see or smell.
NEVER use inside a home or garage,
EVEN IF doors and windows are
open.
Only use OUTSIDE and far away
from windows, doors, and vents.
2.
Keep children away from the equipment, especially while it is operating.
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 4
10. Never split a log that contains any
foreign materials (nails, for example).
11. Never place your hands or body near
a hydraulic fluid leak. High-pressure
fluid can be forced under the skin
resulting in serious injury.
12. Do not use on logs longer than 25” or
with a diameter greater than 8”.
13. Wear ANSI-approved safety goggles,
heavy-duty work gloves, steel-toe
work boots and hearing protection
during use.
14. Do not operate in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust.
Gasoline-powered engines may ignite
the dust or fumes.
15. Stay alert, watch what you are doing
and use common sense when operating this piece of equipment. Do not
use this piece of equipment while
tired or under the influence of drugs,
alcohol or medication.
16. Do not overreach. Keep proper footing and balance at all times. This enables better control of the equipment
in unexpected situations.
17. Dress properly. Do not wear loose
clothing or jewelry. Keep hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
18. Parts, especially exhaust system
components, get very hot during use.
Stay clear of hot parts.
19. Do not cover the engine or equipment
during operation.
20. Keep the equipment, engine, and surrounding area clean at all times.
SKU 65076
21. Use the equipment, accessories, etc.,
in accordance with these instructions
and in the manner intended for the
particular type of equipment, taking
into account the working conditions
and the work to be performed. Use
of the equipment for operations different from those intended could result
in a hazardous situation.
22. Do not operate the equipment with
known leaks in the engine’s fuel system.
23. This product contains or, when used,
produces a chemical known to the
State of California to cause cancer
and birth defects or other reproductive harm. (California Health & Safety
Code § 25249.5, et seq.)
24. When spills of fuel or oil occur, they
must be cleaned up immediately.
Dispose of fluids and cleaning materials as per any local, state, or federal
codes and regulations. Store oil rags
in a bottom-ventilated, covered, metal
container.
25. Keep hands and feet away from
moving parts. Do not reach over or
across equipment while operating.
26. Before use, check for misalignment
or binding of moving parts, breakage
of parts, and any other condition that
may affect the equipment’s operation.
If damaged, have the equipment
serviced before using. Many accidents are caused by poorly maintained equipment.
27. Use the correct equipment for the
application. Do not modify the equipment and do not use the equipment
for a purpose for which it is not intended.
For technical questions, please call 1-800-444-3353.
Page 5
1.
Service precautions
7.
Before service, maintenance, or
cleaning:
Store equipment out of the reach of
children.
8.
Follow scheduled engine and equipment maintenance.
9.
Refueling:
a.Turn the engine switch to its
“OFF” position.
b.Allow the engine to completely
cool.
c. Then, remove the spark plug
wire(s) from the spark plug(s).
2.
Keep all safety guards in place and in
proper working order. Safety guards
include muffler, air cleaner, mechanical guards, and heat shields, among
other guards.
3.
Do not alter or adjust any part of
the equipment or its engine that is
sealed by the manufacturer or distributor. Only a qualified service
technician may adjust parts that
may increase or decrease governed engine speed.
4.
Wear ANSI-approved safety goggles,
heavy-duty work gloves, and dust
mask/respirator during service.
5.
Maintain labels and nameplates on
the equipment. These carry important information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
6.
Have the equipment serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the equipment is maintained. Do not attempt
any service or maintenance procedures not explained in this manual
or any procedures that you are uncertain about your ability to perform
safely or correctly.
SKU 65076
a.Do not smoke, or allow sparks,
flames, or other sources of ignition
around the equipment, especially
when refuelling.
b.Do not refill the fuel tank while the
engine is running or hot.
c. Do not fill fuel tank to the top. Leave
a little room for the fuel to expand as
needed.
d.Refuel in a well-ventilated area only.
Save these
instructions.
For technical questions, please call 1-800-444-3353.
Page 6
Hydraulic Fluid
2.5 Gallons
Rotation viewed from PTO
(power takeoff - the output shaft)
Counterclockwise
To prevent
serious injury
from accidental
starting:
Turn the Power Switch of the
equipment to its “OFF”
position, wait for the engine to
cool, and disconnect the
spark plug wire(s) before
assembling or making any
adjustments to the equipment.
Maximum Log Size
25” Long x 8” Diameter
Tire Air Pressure
60 PSI (cold)
Basic Specifications
Fuel
Type
89+ octane unleaded
gasoline
Capacity
1 Gallon
Equipment Type
Lubricant
Capacity
5W30 (above 32° F)
10W30 (at 32° F or
below)
1.1 Quarts
To prevent
serious injury:
Operate only with proper
spark arrestor installed.
Note: Engine specifications are found in
the engine manual supplied with this
equipment.
Operation of this equipment
may create sparks that
can start fires around dry
vegetation.
A spark arrestor may be
required.
The operator should contact
local fire agencies for laws
or regulations relating to fire
prevention requirements.
Unpacking
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at the number shown on the
cover of this manual as soon as possible.
Set Up Instructions
Read the entire Important
Safety Information
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
Assembly
1.
Due to the size and weight of the Log
Splitter, assembly should be performed with assistance.
2.
Access the Tires (48) for the following
maintenance and assembly steps.
Packing the bearings.
3.
SKU 65076
Using a suitable solvent, clean the
bearings and the rest of the parts in
the Hub assembly. The parts must be
For technical questions, please call 1-800-444-3353.
Page 7
cleaned even if they are new or appear clean.
4.
Allow all pieces to dry completely.
5.
Place fresh, clean bearing grease in
the packer.
6.
With the grease-filled bearing packer
in one hand and the bearing in the
other, press the bear­ing into the
grease, forcing the grease inside the
slots in the bearing, continue doing
this until every slot in the bearing is
completely full of grease.
Hub and Wheel Assembly
7.
Put a Seal (59) and Bearing (49) on
the Axle and then put the Tire on the
Axle.
8.
With each Tire in place, add a Washer (50) and a Spindle Nut (51) onto
the ends of the Axles. Tighten the
Spindle Nuts to 20-25 ft. pounds and
turn each tire several times to seat
the bearing. Back off the Spindle Nut
one half turn. Insert a Cotter Pin (25)
through both the Axle and the Spindle
Nut and bend the end of the Pin
back to hold it in place. Last, tap on a
Wheel Cap (61).
Connecting the Rail Assembly (2) to the
Oil Tank Assembly (10B)
9.
Insert the Front Leg Assembly (11)
into the bracket on the Oil Tank Assembly (10B). Insert the remaining
Hex Bolt (16) through the hole in the
middle of the bracket of the Oil Tank
Assembly (10B). Secure it with a
Hex Nut (17). Refer to the Hex Nut
(17) attached to the Hex Bolt (16) at
the top of the Front Leg Assembly
(11) in FIGURE 1.
SKU 65076
10. When moving the Log Splitter, remove the Push Pin (26) and Hair Pin
Clip (29) and lift the Front Leg Assembly up so that it is parallel to the
Rail Assembly (2). Then, replace the
Push Pin and Hair Pin Clip into the
Horizontal Transport Hole shown just
above the Oil Plug (37), in FIGURES
1 and 2.
11. To connect the Rail Assembly to the
Oil Tank Assembly (10B), insert a Hex
Bolt (16) into the middle hole of the
“L” shaped bracket on the Oil Tank
Assembly. Secure it with a Hex Nut
(17). Refer to the Hex Nut (17) attached to the Hex Bolt (16) just above
the tire in FIGURE 1. Insert the Push
Pin (26) through the hole, as shown
in FIGURE 3.
12. In FIGURES 1 and 2, the Rail Assembly (2) is shown in Horizontal
mode for operation and travel (as
mentioned above, the Front Leg Assembly must be secured up in the
horizontal position when travelling)
Transportation
13. DO NOT TRANSPORT THE LOG
SPLITTER ON PUBLIC ROADS.
The Log Splitter is not certified by the
D.O.T. for use on Public roads.
14. When transporting the Log Splitter,
make sure the hitch (not included) is
compatible with the Hitch Coupler (9).
Follow all of the safety warnings for
towing in the vehicle manufacturer’s
manual. Always use the Safety Chain
with Hook (4) during towing. Do not
tow the Log Splitter at speeds above
45 MPH. As mentioned in step 10,
travel with the Front Leg Assembly
(11) in the horizontal position. The
For technical questions, please call 1-800-444-3353.
Page 8
FIGURE 1
Slide Assembly (3)
Safety Chain
with Hook (4)
Hitch
Coupler (9)
Cylinder (1)
Base
Place Log Here
Hex Head Nut (17) is attached to Hex Bolt (16)
Horizontal transport hole
Push Pin (26) and
Hair Pin Clip (29)
Push Pin (26)
Oil Plug (37)
with air inlet hole
Front Leg Assembly (11)
Rail Assembly (2)
Vertical Position Hole
Hex Nut (17) is attached
to Hex Bolt (16)
Vertical position
locking hole
Oil Removal Plug
Oil Tank (10B)
Wheel Cap (61)
FIGURE 3
FIGURE 2
Horizontal transport hole
Second Push Pin (26) secures
Rail Assembly (2), and is removed
for vertical log splitting.
Air Inlet Hole
Push Pin (26)
Close-up of Push Pin (26) securing the
Front Leg Assembly (11) to the bracket
on the Oil Tank Assembly (10B).
SKU 65076
Oil Plug (37)
with air inlet hole
For technical questions, please call 1-800-444-3353.
Page 9
b.Inspect the equipment and
engine.
c. Fill the engine with the proper amount and type of fuel
and oil.
d.Read the Equipment Operation section that follows.
Rail Assembly must always be secured in the horizontal position for
travel. Cover the air inlet hole on the
Oil Plug (37) before transport. See
FIGURE 3.
15. Pull up and down on the Hitch Coupler to make sure the hitch ball is
fitting snugly in the Hitch Coupler.
There should be no play between the
hitch ball and Hitch Coupler. If there
is play, tighten the Adjustment Nut
until no play is present. If the Adjustment Nut is too tight, the Handle will
not lock.
Note: The hitch will accept a 2 inch hitch
ball.
1.
Start and operate the engine according to the provided engine manual.
Equipment Operation
1.
Start and operate the engine according to the provided engine manual.
2.
Block the wheels before changing
the position (vertical/horizontal) of the
unit.
Operating Instructions
FIGURE 4
Read the entire Important
Safety Information
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Vertical Position
Engine Operation
Inspect engine and equipment
looking for damaged, loose,
and missing parts before
set up and starting. If any
problems are found, do not use
equipment until fixed properly.
Start Procedure
Before starting the engine:
a.Follow the Set Up Instructions to prepare the equipment. Follow all instructions
in the separate engine manual provided with the engine.
SKU 65076
Place
Log
Here
Base
3.
In FIGURE 1, the Rail Assembly (2) is
shown in Horizontal mode for operation and travel. In FIGURE 4 the unit
is shown in the vertical position. To
change positions, remove the Hair
Pin Clip (29) and the Push Pin (26). A
close-up of this Push Pin is shown in
FIGURE 3. Tilt the unit to the vertical
position as shown in FIGURE 4, and
replace both the Push Pin and the
For technical questions, please call 1-800-444-3353.
Page 10
Hair Pin Clip into the vertical position
hole (See FIGURE 1). Reverse the
process to return to the horizontal
position.
4.
Remove the Oil Plug (37) and fill the
tank with Hydraulic oil (not included).
To check the oil level remove the
Dipstick (62), check the level then
replace it. The oil should be at the
upper notch of the Dipstick. Be sure
that a constant hydraulic oil level of
2.5 gallons is maintained.
5.
The hydraulic system must be vented
during operation or it may become
vacuum locked and stop working
properly. To vent the system, open
the air inlet hole (See FIGURE 3)
by loosening the Oil Plug. You may
have to move the O-ring to expose
the air inlet vent. When the Log
Splitter is not in operation or being
transported, close the air inlet hole by
tightening the Oil Plug (37).
6.
The maximum length of each log can
not exceed 25 inches or a diameter of
8 inches.
7.
Place the log on the Splitter Base as
shown in FIGURES 1 and 4. Make
sure the wedge on the Slide Assembly is facing the log. (See FIGURE 1).
8.
Grip the Directional Valve (58) and
move it into the lower position to split
the log.
9.
To back the wedge off the log, move
the Directional Valve away from the
log just split.
11. To prevent accidents, turn off the
engine and disconnect its spark plug
wire after use. Wait for the engine to
cool, clean external parts with clean
cloth, then store the equipment out
of children’s reach according to the
Storage instructions in this manual.
10. Once the log is split, remove the pieces. Continue, as explained above,
until all logs are split.
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 11
Servicing
To prevent
serious injury
from accidental
starting:
Turn the Power Switch of the
equipment to its “OFF”
position, wait for the engine to
cool, and disconnect the
spark plug wire(s) before
performing any inspection,
maintenance, or cleaning
procedures.
To prevent
serious injury
from equipment failure:
Do not use damaged
equipment. If abnormal noise,
vibration, or excess smoking
occurs, have the problem
corrected before further use.
Maintenance Procedures
Many maintenance procedures,
including those not detailed
in this manual, will need to
be performed by a qualified
technician for safety. If you
have any doubts about your
ability to safely service the
equipment or engine, have a
qualified technician service the
equipment instead.
Note: These procedures are in addition to
the regular checks and maintenance
explained as part of the regular operation of the engine and equipment.
Engine Maintenance and Service
Follow the instructions found in the
included engine manual.
SKU 65076
Equipment Lubrication
1.
Gear Box is shipped properly filled
with grease.
2.
Yearly, open the Gear Box and check
the grease level.
3.
Add grease only up to top of gears.
Do not overfill grease; overfilling
will damage the equipment.
Storage
1.
Wait for engine to cool, then clean
equipment with clean cloth.
2.
Clean the engine and/or prepare it for
storage according to engine manual
instructions.
3.
Apply a thin coat of rust preventive oil
to all uncoated metal parts.
4.
Cover and store in a dry, well-ventilated area out of reach of children.
5.
For cold weather operation, store
the equipment in a cool dry area to
prevent condensation and premature
wear.
Transportation
1.
BEFORE Transporting, check the
Tires for wear and proper inflation (60
PSI, cold).
2.
Before Transporting and at 500 MILE
intervals during every trip, check and
tighten the Tire Lug Nuts. Torque
from 85 to 90 ft-lb.
3.
EVERY 2,000 TO 3,000 MILES of
Travel, lubricate the Hub Assemblies
with a heavy weight bearing grease.
Follow the Bearing Packing Instructions as explained on the last page
of this manual. After each Hub As-
For technical questions, please call 1-800-444-3353.
Page 12
sembly is reassembled, tighten the
Castle Nut until the wheel starts spinning with slight resistance. Loosen
the Castle Nut about 1/2 turn from
this point. Insert a new Cotter Pin
through the Castle Nut and the hole
in the axle. Bend the Pin back, locking it and the Nut in place.
Hydraulic System Care
1.
The recommended interval for changing the hydraulic oil and filter is every
3 months with regular use.
2.
If the Log Splitter begins to lose power or splitting efficiency, it may be a
result of air becoming trapped in the
hydraulic system. Follow the steps
below to bleed air from the system.
3.
Loosen the Oil Plug (37) and move
the O-ring out of the way to expose
the air hole in the Oil Plug.
4.
Remove the spark plug from the
engine (see engine manual) to keep
the engine from starting during this
process.
5.
Push the Directional Valve (58) forward, toward the front of the Cylinder
(1) (see FIGURE 1).
6.
Pull the engine starter cord 10-15
times until the hydraulic cylinder piston moves forward.
7.
Tighten the Oil Plug (37).
8.
Replace the spark plug.
9.
Test the Log Splitter to make sure it is
operating properly. If not, repeat the
above process.
PLEASE READ THE FOLLOWING
CAREFULLY
The manufacturer and/or distributor
has provided the parts list and
assembly diagram in this manual as
a reference tool only. Neither the
manufacturer or distributor makes
any representation or warranty of
any kind to the buyer that he or she
is qualified to make any repairs to the
product, or that he or she is qualified
to replace any parts of the product.
In fact, the manufacturer and/or
distributor expressly states that
all repairs and parts replacements
should be undertaken by certified
and licensed technicians, and not by
the buyer. The buyer assumes all risk
and liability arising out of his or her
repairs to the original product or
replacement parts thereto, or arising
out of his or her installation of
replacement parts thereto.
10. Warning! Only a qualified technician
should repair or service the internal
hydraulic system of this unit.
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 13
Parts list
Part
1
2
3
4
5
6
7
8
9
10B
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Description
Cylinder
Rail Assembly
Slide Assembly
Safety Chain With Hook
Slide Guide
Slide Retainer
Bolt 1/2’’*2-1/2’’
Hex Nut 1/2’’
Hitch Coupler
Oil Tank Assembly
Front Leg Assembly
Hex Head Bolt 1/2’’*1-3/4’’
Hex Nut 1/2’’
Hex Head Nut 3/8’’
Washer 1/2’’
Hex Head Bolt 9/16’’*1-1/4’’
Hex Nut 9/16’’
Washer
Hex Head Bolt 5/16’’*2-3/4’’
Hex Head Nut 3/8’’
O Ring Seal
Hex Head Bolt 1/2’’*1-3/4’’
Hex Nut 5/16’’
Spring Washer 5/16’’
Cotter Pin
Push Pin
Clevis Pin
Hair Pin Clip
Hair Pin Clip 2.5’’
Slide Holder
Hydraulic Tubing
Qty.
1
1
1
1
2
2
6
7
1
1
1
2
2
3
2
2
2
1
1
1
1
4
4
8
2
2
1
2
2
1
1
Part
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Description
High Pressure Hose
Return Hose
Inlet Hose
Hose Clamp
Male Connector
Oil Plug
High Pressure Fitting
90° Elbow Fitting #2
90° Elbow Fitting #3
Hex Head Bolt 3/8’’*3/4’’
Hex Head Bolt 5/16’’*1’’
Oil Filter
Pump Mounting Bracket
Pump
Hex Head Bolt 5/16’’*1’’
Hex Head Bolt 3/8’’*3-1/4’’
Tire
Bearing 30205E
Washer 3/4’’
Spindle Nut
Coupling -Pump Side
Coupling -Engine Side
Pump Key 1/8’’
Engine Key
Hex Screw
Engine
Directional Valve
Seal
Hex Head Bolt 3/8’’*3-1/2’’
Wheel Cap
Dipstick
Qty.
1
1
1
4
1
1
1
2
2
1
4
1
1
1
4
2
2
4
2
2
1
1
1
1
2
1
1
2
1
2
1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 14
08
2
ASSEMBLY DIAGRAM
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 15
Hydraulic Ram Seals
Warning! Only a qualified technician should repair or service the internal hydraulic
system of this unit.
Seal Kit
SKU 65076
Model
Part Sku
65076
26671
For technical questions, please call 1-800-444-3353.
Page 16
Hydraulics Drawing
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 17
Limited 1 year / 90 Day warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period
of ninety days from date of purchase that the engine/motor, the belts (if so equipped),
and the blades (if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from
date of purchase, that all other parts and components of the product are free from
defects in materials and workmanship (90 days if used by a professional contractor or
if used as rental equipment). This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our
facilities, normal wear and tear, or to lack of maintenance. We shall in no event be liable
for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. This warranty is expressly in lieu of all
other warranties, express or implied, including the warranties of
merchantability and fitness.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 65076
For technical questions, please call 1-800-444-3353.
Page 18