Harbor Freight Tools 66342 User's Manual
Add to My manualsHarbor Freight Tools 66342 is an electric, rechargeable, and cordless shaver designed for shaving facial hair. It features a powerful motor that provides 9000 oscillations per minute (OPM) for a close and efficient shave. The shaver comes with two foils and a foil holder that can be easily removed and cleaned under running water. It also includes a carrying sleeve for convenient storage and travel. The shaver has a built-in Ni-Cd battery that provides up to 5-7 hours of shaving time on a single charge.
advertisement
recHarGeaBle/cordless sHaVer
66342
InstructIons and precautIons
distributed exclusively by Harbor Freight tools ® .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
saVe tHese InstructIons. read all precautIons and InstructIons.
Copyright © 2008 by Harbor Freight Tools ® . All rights reserved. No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
specIFIcatIons
Charging Time 5-7 Hours
Speed
9000 OPM
(Oscillations Per Minute)
Charger Input 3VDC
Internal Battery Ni-Cd
unpackInG
When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this document as soon as possible.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Important saFetY
InFormatIon
Do not expose to moisture while charging.
Do not reach for a plugged in Shaver that has fallen into water. Unplug immediately and drain water.
Do not charge near heater or in direct sunlight.
Do not use if Charger (5) or Charger cord has been damaged.
Do not attempt to remove Foil covering with screwdriver or other tools.
Do not use without Foil (2) and Foil Holder
(3) in place.
This product is not a toy. Do not allow children to play with this item.
Use as intended only.
Inspect before every use; do not use if parts are loose or damaged.
Turn off Shaver before charging.
Do not charge immediately after prolonged use. Allow it to cool before charging.
Rinse off Shaver after each use and keep stored in dry, cool environment out of children’s reach.
Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
1.
2.
3.
4.
5.
1.
2.
3.
4.
2.
3.
1.
read the entIre Important saFetY InFormatIon section at the beginning of this document including all text under subheadings therein before set up or use of this product.
cHarGInG InstructIons
Attach the power cord of the Charger (5) into the bottom of the Shaver (1). Plug the Charger into an electrical outlet that is away from a sink or other source of water. note: Make sure Shaver Switch (8) is turned to OFF.
Once plugged in, the LED Charger light on the front of Shaver housing will activate.
Charge for 5 to 7 hours. Do not charge for longer than required charge time.
operatIon InstructIons
Once fully charged, remove Charger cord from housing, remove Cover (4) and turn
Switch to ON.
Gently guide Shaver along face and chin to remove beard. Use short, back and forth strokes. Note: Do not apply too much pressure while shaving.
If you have not used an electric shaver before, your skin may become irritated after use. This is a natural reaction that may last for a few days until your skin adjusts to
Shaver.
When finished shaving, turn Switch to OFF.
Slide the Cover onto Shaver head until ready to use again. For travelling purposes, slide the Shaver into the Carrying Sleeve (7).
cleanInG tHe sHaVer
After each use, beard and hair cuttings may collect in Foil. Clean Foil by rinsing Shaver head under cool running water.
WarnInG!
Only clean when Shaver is disconnected from Charger and switch is turned to OFF.
Hair trimmings may get under Foil and/or it may be necessary to replace Foil. First, press down on the tabs on either side of the
Foil Holder (3).
Slide Foil Holder off of the top of Shaver housing, exposing the Shaver cutting heads.
SKU 66342
For technical questions, please call 1-800-444-3353.
Page 2
5.
6.
7.
8.
9.
10.
1.
2.
3.
4.
5.
If necessary, use Brush (6) to clean hair trimmings from exposed Shaver cutting heads.
If necessary, slide old Foil from out of Foil
Holder and rinse trimmings off Foil.
If Foil must be replaced, slide the new Foil into Foil Holder so that small hole in the center of the Foil slides over small tab in the middle of the Foil Holder cross bar. This will hold Foil in place.
Slide the Shaver housing into the Foil Holder until it snaps into place.
Slide the Cover onto Shaver head until ready to use.
Recharge if necessary.
remoVInG tHe BatterY
By law, the Ni-Cd battery must be removed from housing before Shaver disposal.
Use a screwdriver to unscrew the Shaver head from the top of the housing.
Pry off the label from the housing bottom and unscrew bottom from housing.
Pry front panel off Power Switch and remove screw from front panel.
Slide battery holder out of housing. Remove and properly dispose of Ni-Cd battery. part
7
8
5
6
3
4
1
2
parts lIst & dIaGram
description
Shaver
Foils
Foil Holder
Cover
Charger
Brush
Carrying Sleeve
Power Switch
Qty.
1
1
1
1
1
1
1
2 record serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
please read tHe FolloWInG careFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED
THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS DOCUMENT
AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy
OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO
MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN By
CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER.
THE BUyER ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
4
6
3
2
7
8
1
SKU 66342
Please note: Charger (5) is not shown.
For technical questions, please call 1-800-444-3353.
Page 3
advertisement
Related manuals
advertisement