Harbor Freight Tools 66950 User's Manual

16” OSCILLATING STAND
FAN
66950
Set up and Operating Instructions
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
Read and save these instructions.
Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
CAUTION
Read Rules for Safe Operation and
Instructions Carefully.
WARNING
1.
2.
3.
To reduce the risk of fire or electric shock, do not use this Fan
with any solid-state speed control
device.
This appliance has a polarized
plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to
fit into a polarized outlet only one
way. If the plug does not fit fully
in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician. Do not change the
plug in any way. Do not attempt to
defeat this safety feature.
Do not leave Fan running while
unattended.
RULES FOR SAFE
OPERATION
1.
Never insert fingers, pencils, or any
other object through Front Grill (2) or
Rear Grill (6).
2.
Disconnect Fan when moving it from
one location to another.
3.
Disconnect Fan before removing
grilles for cleaning.
4.
Be sure fan is on a stable surface
when operating to avoid tipping.
5.
DO NOT use fan in window. Rain
may create electrical hazard.
SKU 66950
6.
Complete the assembly of the fan
before switching on the fan.
Save these
instructions.
Safety Symbols
In this manual, on the labeling,
and all other information provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
For technical questions, please call 1-800-444-3353.
Page 2
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
Additional Safety Instructions
1.
Maintain labels and nameplates on
the tool. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
2.
Do not run Power Cord (36) under
carpeting. Do not cover Cord with
throw rugs, runners or similar coverings. Arrange cord away from traffic
area and where it will not be tripped
over.
3.
Use only in dry environments. Do not
use in bathrooms, laundry area, near
sinks or other sources of water.
4.
Do not run Fan without Front and
Rear Grills (2, 6) in place.
5.
This product is not a toy. Keep it out
of reach of children.
6.
WARNING: Handling Cord on this
product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (California Health & Safety Code § 25249.5,
et seq.)
7.
The warnings, precautions, and instructions discussed in this instruction
manual cannot cover all conditions
and situations that may occur. It must
be understood by operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by operator.
SKU 66950
Specifications
Electrical Requirements
120 V~ / 60 Hz / .37 A
Speeds (approximately)
Low: 1120 RPM
Medium: 1280 RPM
High: 1420 RPM
HOUSEHOLD USE ONLY
E197533
Unpacking
When unpacking, make sure item is
intact and undamaged. If parts are missing or broken, call Harbor Freight Tools at
1-800-444-3353 as soon as possible.
Save This Manual
Keep this manual for safety warnings
and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write product’s serial number in
back of manual near assembly diagram (or
month and year of purchase if product has
no number). Keep this manual and receipt
in a safe place for future reference.
For technical questions, please call 1-800-444-3353.
Page 3
ASSEMBLY
Read the entire RULES FOR
SAFE OPERATION section at
the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
To prevent
serious injury
from accidental
operation or electric
shock: Before assembly,
cleaning or adjustment, make
sure OFF key is pressed and
the cord is unplugged.
3.
Extend Upper Column (42) from
Lower Shaft and thread Height Adjustment Knob back onto Lower
Column until its threaded back into
place. WARNING! This must be done
before top half of Fan is assembled
onto Upper Column.
4.
Unthread Spinner (3) from Spindle
(7) by turning it clockwise. Remove
Plastic Nut (5) from Motor Housing,
by turning it counterclockwise. See
Figure B, below.
3
5
23, 25
Note: For additional information regarding
parts listed, refer to Assembly Diagram at back of manual.
24
4
6
7
42
28
41
2
30
29
33
5.
Slide Rear Grill (6) over retainer on
face of Motor Housing, aligning locator pin on Housing with pin hole for
Rear Grill. In this mode, the catch
on edge of Rear Grill will be at lowest position. Thread on Plastic Nut
(5) clockwise, but do not overtighten.
See Figure B.
6.
Insert Propeller over Spindle. Align
cross-pin of Spindle with recess in
the inner face of Propeller. Attach
Spinner (3), turning it counterclockwise to tighten. See Figure B.
7.
Fasten Front Grill (2) onto Rear Grill
(6) using latches along edges of both
Grills and the locking screw on the
34
Figure A
1.
2.
Using Screws (30) and Washers (31,
32), attach Lower Shaft (41) to Upper
Cross Stand (33) and Lower Cross
Stand (34). See Figure A, above.
Unthread and remove Height Adjustment Knob (28) from Lower Shaft.
Slide Base Cover (29) down Shaft
until it covers intersection of Upper
and Lower Cross Stands.
SKU 66950
41
Figure B
For technical questions, please call 1-800-444-3353.
Page 4
Rear Grill. WARNING! Do not activate Fan until properly latched.
8.
INSPECTION AND MAINTENANCE
To prevent
serious injury
from accidental
operation or electric
shock: Before appliance
inspection or maintenance,
make sure Off key is pressed
and Power Cord is unplugged.
Use Screws (24) to fasten Front and
Rear Shaft Housing (23, 25) to Upper
Shaft. See Figure B.
Operation
Read entire RULES FOR
SAFE OPERATION section at
beginning of manual including
all text under subheadings
therein before set up or use.
1.
To make the fan oscillate, push the
Knob (11) down. To make the fan
stop oscillating, pull the Knob up.
2.
To adjust the angle of air flow, tilt the
Housing (12) and move to desired
angle.
3.
To adjust height of fan, loosen the
Height Adjustment Knob (28) and
raise or lower fan. Retighten Knob
once desired height is reached.
4.
To activate, plug the Power Cord (36)
into the nearest wall outlet.
5.
To adjust the speed, push one of the
desired Switches (21). The available
speeds are Low, Medium and High.
To turn off fan, press the Off Switch.
To prevent serious
injury from Appliance
failure: Do not use
damaged appliances. If
abnormal noise or vibration
occurs, have the problem
corrected before further use.
1.
BEFORE EACH USE, inspect condition of the Fan. Check for loose
screws, misalignment or binding of
moving parts, cracked or broken
parts, and any other condition that
may affect its safe operation.
2.
Clean regularly to prevent dust from
accumulating on Propeller (4). Unfasten latches along Front and Rear
Grills, remove Front Gill, and use
damp cloth to wipe Blade. Dry and
replace Front Grill before use.
3.
To maximize air circulation, dismantle
Grills and Propeller and wash and dry
each part when dirty.
4.
WARNING! Do not allow any water to
get into the Motor (8).
PLEASE READ THE FOLLOWING CAREFULLY
The manufacturer and/or distributor has provided the parts list and assembly diagram in
this manual as a reference tool only. Neither the manufacturer or distributor makes any
representation or warranty of any kind to the buyer that he or she is qualified to make any repairs
to the product, or that he or she is qualified to replace any parts of the product. In fact, the
manufacturer and/or distributor expressly states that all repairs and parts replacements should
be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all
risk and liability arising out of his or her repairs to the original product or replacement parts
thereto, or arising out of his or her installation of replacement parts thereto.
SKU 66950
For technical questions, please call 1-800-444-3353.
Page 5
PARTS LIST AND ASSEMBLY DIAGRAM
Part
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Description
Center Piece
Front Grill
Spinner
Propeller
Plastic Nut
Rear Grill
Spindle
Motor
Connector
Oscillating Lever
Knob
Housing
Screw
Screw
Insulator
Screw
Neck
Positioning Board
Spring
Screw
Speed Switches
Clip
Front Shaft Housing
Screws
Rear Shaft Housing
Nut
Screws
Height Adjustment Knob
Base Cover
Screw
Washer
Washer
Upper Cross Stand
Lower Cross Stand
Leg Cap
Power Cord
Cord Clamp
Spring
Ball
Screws
Lower Column
Upper Column
SKU 66950
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
4
1
1
1
1
1
4
4
4
1
1
4
1
1
1
1
1
1
1
42
41
Record Product’s Serial Number Here:
Note: If product has no serial number,
record month and year of purchase
instead.
Note: Some parts are listed and shown
for illustration purposes only, and
are not available individually as replacement parts.
For technical questions, please call 1-800-444-3353.
Page 6