Harbor Freight Tools 68333 User's Manual

Electric Pressure Washer
68333 - Electric Pressure Washer
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
When unpacking, make sure that the product is intact and undamaged.
If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.
Visit our website at: http://www.harborfreight.com
Copyright© 2011 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
Safety Warnings
Specifications
Electrical Input 120 V~ / 60 Hz / 12 A (Rated)
Maximum
1,500 PSI
Pressure
Maximum
1.3 GPM
Flow Rate
High Pressure
13 ft.
Hose
Power Cord
1. Read all the instructions before using the product.
2. To reduce the risk of injury, close supervision is
necessary when a product is used near children.
3. Know how to stop the product and bleed pressures
quickly. Be thoroughly familiar with the controls.
35 ft.
4. Stay alert – watch what you are doing.
Save This Manual
Keep this manual for the safety warnings and
precautions, assembly, operating, inspection,
maintenance and cleaning procedures. Write the
product’s serial number in the back of the manual near
the assembly diagram (or month and year of purchase
if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference.
Important Safety Instructions
In this manual, on the labeling, and all other
information provided with this product:
This is the safety alert symbol. It is
used to alert you to potential personal
injury hazards. Obey all safety
messages that follow this symbol to
avoid possible injury or death.
DANGER indicates a hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol,
indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices
not related to personal injury.
CAUTION, without the safety alert symbol, is used
to address practices not related to personal injury.
Page 2
WARNING When using this product
basic precautions should always be
followed, including the following:
5. Do not operate the product when fatigued or under
the influence of medication, alcohol or drugs.
6. Keep operating area clear of all persons.
7. Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
8. Follow the maintenance instructions
specified in the manual.
9. This product Is provided with A Ground Fault
Circuit Interrupter (GFCI) built into the power
cord plug. If replacement of the plug or cord is
needed, use only identical replacement parts.
10. WARNING – Risk of injection or injury– do
not direct discharge stream at persons.
11. Connect to individual branch circuit only.
12. WARNING – To reduce the risk of electrocution,
keep all connections dry and off the ground.
Do not touch plug with wet hands.
13. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the pressure
washer. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
14. GFCI Precautions
Test GFCI (Ground Fault Circuit Interrupter)
before each use as follows:
a. Plug GFCI into power outlet and press
reset button. Indicator should turn on.
b. Press test button. Indicator should turn off.
c. Press reset button again for use.
Do not use if above test fails.
The GFCI device does not protect against electrical
shock due to contact with both circuit conductors or a
fault in any wiring supplying the GFCI device.
To allow GFCI unit to function properly,
extension cords must not be
used with this pressure washer.
For technical questions, please call 1-800-444-3353.
SKU 68333
Set up Precautions
1. The work area should have adequate
drainage to reduce the possibility of a fall
or electric shock due to wet surfaces.
2. Wear ANSI-approved safety goggles
during set up and use.
3. Only feed cold, clean water through this tool.
Pressure washer detergent may be used in
the soap dispenser only. Do not use caustic
materials, solvents, flammable materials, or
detergents not designed for pressure washers.
Use of any such material can cause injury,
or damage this tool or personal property.
4. Prior to starting the Pressure Washer in cold weather,
check all of the parts of the unit to make sure ice
has not formed. Do not store the unit anywhere
that the temperature will fall near 32° F (0° C).
Operating Precautions
1. Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing pressure washers. Such
preventive safety measures reduce the risk of
starting the pressure washer accidentally.
2. Do not leave the equipment unattended
when it is running. Turn off the equipment
before leaving the work area.
3. Wear ANSI-approved safety goggles and heavyduty nonslip rubber work boots during use.
4. Use only accessories that are recommended by
Harbor Freight Tools for your model. Accessories
that may be suitable for one piece of equipment may
become hazardous when used on another one.
5. This product must continuously run with
cold water only. Never use hot water. Do
not dry run this product. Dry running will
cause serious damage to the seals.
6. To avoid electrical shock, never start and run the
Pressure Washer in the rain. Never allow water
to leak into the Body of the Pressure Washer.
Do not direct discharge stream at the Pressure
Washer itself or at other live electrical equipment.
7. Do not allow the GFCI Plug to become wet. Always
place the GFCI Plug in a dry location and as far
away as possible from the object being sprayed.
8. When using the Pressure Washer, always
maintain a firm grip on the Spray Gun with
both hands. Squeezing the Trigger of the
Spray Gun causes a kickback force.
9. Do not feed already-pressurized water (such as that
from another pressure washer) into this washer.
SKU 68333
10. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
11. WARNING: The brass components of this
product contain lead, a chemical known to
the State of California to cause birth defects
(or other reproductive harm). (California
Health & Safety code § 25249.5, et seq.)
12. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
13. Use the correct equipment for the application.
Do not modify the equipment and do not use the
equipment for a purpose for which it is not intended.
14. If water is leaking out of the Pressure Washer
immediately turn off the unit. Unplug the
Pressure Washer, and discharge all pressure
before tightening fittings or having repair
work done by a qualified technician.
15. When the engine is running, do not allow
the Pressure Washer to remain idle for more
than two minutes. If allowed to remain idle,
the water in the unit will heat up, possibly
causing damage to the Pressure Washer.
16. The high pressure water flow can damage
the work surface if not used properly. Always
test the spray in an open area first.
17.
Injection Hazard. The high pressure
water jet produced by this tool can cut
skin or cause injury to hands or eyes.
Do not allow spray to strike you and do
not spray toward people or animals. Do
not spray the tool itself or any electrical source.
18. This Pressure Washer is intended for
outdoor residential use only.
19. In case of an emergency during use,
immediately release the trigger on the spray
handle, turn the power switch off and then
unplug the unit. Do not set the spray handle
down without turning off the power switch.
Vibration Hazard:
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical checkups to ensure medical problems are not being
For technical questions, please call 1-800-444-3353.
Page 3
caused or worsened from use. Pregnant women
or people who have impaired blood circulation
to the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration when there
is a choice between different processes.
5. Include vibration-free periods each day of work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
Save these
instructions.
Page 4
For technical questions, please call 1-800-444-3353.
SKU 68333
Ground Fault Circuit
Interrupter Protection
This pressure washer is provided with a groundfault circuit-interrupter (GFCI) built into the
plug of the power-supply cord. This device
provides additional protection from the risk of
electric shock. Should replacement of the plug
or cord become necessary, use only identical
replacement parts that include GFCI protection.
Servicing a
Double-Insulated Appliance
In a double-insulated product, two systems of
insulation are provided instead of grounding. No
grounding means is provided on a double-insulated
product, nor should a means for grounding be
added to the product. Servicing a double-insulated
product requires extreme care and knowledge of the
system, and should be done only by qualified service
personnel. Replacement parts for a double-insulated
product must be identical to the parts they replace.
A double-insulated product is marked with the words
“DOUBLE INSULATION” or “DOUBLE INSULATED.”
The symbol
may also be marked on the product.
Extension Cords
DO NOT use an extension cord with this product.
SKU 68333
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~
A
Volts Alternating Current
Amperes
n0 xxxx/min. No Load Revolutions per Minute (RPM)
WARNING marking concerning Risk
of Eye Injury. Wear ANSI‑approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.
WARNING marking concerning
Risk of Injection.
Do not direct spray at any
person or animal.
For technical questions, please call 1-800-444-3353.
Page 5
Instructions for Putting into Use
Read the entire Important
Safety Information section at the
beginning of this manual including
all text under subheadings therein
before set up or use of this product.
water pressure from the unit before assembling
or making any adjustments to the tool.
Check the Inlet Strainer for any blockage, including
packaging debris. The Pressure Washer may
be shipped with a plastic plug in the Inlet.
Note: For additional information regarding the parts
listed in the following pages, refer to Parts List and
Assembly Diagram on page 14. Some of the following
assembly steps may have been performed at the factory.
To prevent serious injury from
accidental operation:
Turn the Power Switch of the tool off, unplug
the tool from its electrical outlet, shut off the
water supply and safely discharge all residual
Components
Soap Dispenser
Handle
Power
Switch
Extension
Nozzle
Body
Water Supply
Inlet
(on back)
Spray Gun
High Pressure
Hose
Pressure Hose Outlet
Note: Check for and remove any shipping plugs from the Water Supply Inlet and Pressure Hose Outlet on the
front of the machine.
Page 6
For technical questions, please call 1-800-444-3353.
SKU 68333
Assembly
1. Snap the Body onto
the Base until it clicks
into place.
2. Attach the
Handle to
the front of
the Body
with four of
the Screws.
3. Attach the Strap for
the Soap
Dispenser to the
Base with the
remaining two
Screws.
4. Thread the High
Pressure Hose
onto the Pressure
Hose Outlet on the
front of the body.
5. Snap the High Pressure Hose
to the Spray Gun until it clicks
in place.
6. Place the Water
Filter in the
Water Supply
Inlet and thread
the adapter
onto the Inlet.
Note: To remove the Pressure Hose from the Spray Gun, press and hold the hose release button on the side of the
Spray Gun and pull out the hose.
SKU 68333
For technical questions, please call 1-800-444-3353.
Page 7
Features
Operating Instructions
Note: Familiarize yourself with the location
and function of all of the machine’s controls
before proceeding to setup of the machine.
1. This item is equipped with a GFCI (Ground Fault
Circuit Interruption) plug. Read and follow these
GFCI precautions:
WARNING! To prevent electric shock and
death:
Test GFCI (Ground Fault Circuit Interrupter)
before each use as follows:
INDICATOR
RESET
BUTTON
TEST
BUTTON
FIGURE A
a. Make sure the trigger is released and
plug GFCI into power outlet. Press reset
button. Indicator should turn on.
b. Press test button. Indicator should turn off.
c. Press reset button again for use. Do
not use if above test fails.
The GFCI device does not protect
against electrical shock due to contact
with both circuit conductors or a fault
in any wiring supplying this device.
Should replacement of the GFCI Power
Plug become necessary, only a qualified
technician should perform the service.
Do not alter or disable the GFCI Power Plug.
To allow the GFCI unit to function
properly, extension cords must not be
used with this pressure washer.
2. The Spray Control Sleeve on the Spray Wand
can be rotated for a range of spray patterns,
from a full fan spray to a direct stream spray.
3. When not in use the Trigger can be locked by
moving it completely forward, then pressing
the red button closest to the hose. Press the
other red button to unlock the Trigger.
Page 8
Read the entire Important
Safety Information section at the
beginning of this manual including
all text under subheadings therein
before set up or use of this product.
Work Piece and Work
Area Set Up
1. Designate a work area that is clean and welllit. The work area must not allow access by
children or pets to prevent distraction and injury.
2. Check the water supply. Prior to using the
Pressure Washer for the first time, it is ESSENTIAL
to verify that the water supply is adequate. The
Pressure Washer needs TWICE the water supply
(or volume) than the stated water output (1.3 GPM).
This Pressure Washer will need about 2.6-3 GPM to
operate correctly and efficiently. If the water is being
supplied by a well/pump, make certain that the well/
pump produces enough water to keep up with the
Pressure Washer’s water demands. Water supply
hoses should be heavy duty to withstand the forces
involved. Water hoses up to 25' long must be 5/8" ID.
Water hoses up to 50' long must be 3/4" ID. Do not
use hoses longer than 50'. The more minerals in the
water (the harder the water) you use, the more often
mineral buildup will need to be cleaned out from the
nozzles. The flow rate of the water supply must never
be allowed to fall below 2.6 GPM.
To determine the water supply’s flow rate: Run the
water at full for one minute into a 5 gallon container,
and measure the amount of water in the container.
CAUTION! If the Pressure Washer is run
with an inadequate water supply, the pump
will cavitate. Cavitation causes the pump
to operate loudly and will damage it.
3. Arrange for a proper electrical supply.
This unit uses a large amount of current, especially
during start-up. Turn off power switch, then connect
this unit only to a dedicated household circuit
capable of providing ample current to it. A dedicated
circuit has no additional loads (running devices)
connected to it; shut off any appliances that slow
down or lights that dim while the washer is running.
For best results, connect the plug to that circuit’s
outlet that is nearest to the circuit breaker panel.
4. Plan out the job: Plan out what areas will be
cleaned, how many sessions will be necessary,
and how long the individual sessions of work will
need to be. Plan to clean the higher portions first,
because the higher portions will typically remain
cleaner while the other areas are cleaned. Plan a
safe direction for runoff to flow while the job is being
performed, and plan on working your way in that
For technical questions, please call 1-800-444-3353.
SKU 68333
direction. You will have a clearer idea of the time
involved to clean the area after doing a test run.
5. Clear the cleaning area of all objects that
are not being cleaned. If any water prone or
delicate items cannot be moved, protect them. If
detergent is to be used, cover or remove any
plants or animals that may be damaged by the
detergent. Disconnect power to and protect any
nearby electrical wiring from water and spray.
6. Place the Pressure Washer in a location which is
protected from any water from the cleaning area.
Select a location higher than the cleaning area. The
pressure washer’s location should be close enough
so that the hose will reach every portion of the job to
be done with some slack for movement. Also, select
an area with proper access to a dedicated circuit.
c. Insert the Extension Nozzle into the large end
of the Dispenser cap, pressing until it clicks into
place.
7. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
Tool Set Up
To prevent serious injury from
accidental operation:
Turn the Power Switch of the pressure washer
off, unplug it from its electrical outlet, and
relieve all pressure in a safe manner before
making adjustments or installing accessories.
3. Before connecting the water supply, run
water through the garden hose (sold
separately) to remove any debris.
1. Make sure the washer is clean and ready
for use. Ensure the inlet water strainer, nozzle,
and the rest of the Washer are completely free of
buildup or debris.
4. Turn off the water, then thread the garden
hose onto the Water Supply Inlet on
the back of the Pressure Washer.
Attach the Extension Nozzle by inserting
it into the end of the gun then rotating it
clockwise until it clicks into place.
Reset Button
Test Button
2. If using the Soap Dispenser:
a. Remove the dispenser lid and fill with pressure
washer detergent (sold separately).
5. Plug the power cord into a power outlet and test
the GFCI by pressing the Reset and Test buttons
as described in Controls and Features section.
b. Set the spray to the fan setting by turning the
end of the Extension Nozzle counterclockwise.
SKU 68333
For technical questions, please call 1-800-444-3353.
Page 9
General Operating Instructions
1. Point the Nozzle in a safe direction and
squeeze the trigger to check that all pressure is
released from the unit. Release the Trigger.
2. Turn on the water supply, then
turn on the Power Switch.
Note: If the unit does not turn on or turns off
suddenly, check and reset the GFCI.
3. Unlock and squeeze the Trigger to start
the stream. Be aware that when it is first
started, the gun will kick back.
4. Test spray the edge of the surface to be cleaned
to make sure that the stream is not too strong for
the surface. Adjust the pressure by squeezing
the Trigger more or less, and by changing your
distance from the surface. Adjust the stream from
a fan to a direct stream by turning the nozzle.
5. When finished using the Pressure Washer,
release the Trigger, turn the Power Switch off,
unplug the unit, and turn off the water supply.
6. Point the Nozzle in a safe direction and squeeze
the trigger to check that all pressure is released
from the unit. Release and lock the Trigger.
7. Clean, then store indoors, out of children’s reach.
Operating Tips
Become Familiar With your Machine:
1. Before beginning work, set aside enough
time to familiarize yourself with this machine’s
cleaning rate and capacity along with all
instructions and precautions contained in this
section, along with the Operating Instruction
and Controls and Features sections.
2. This unit is intended for various light to moderate
cleaning applications. If deeper cleaning is desired, it
can be attained at times, however this is done at the
expense of speed. This unit is not intended for paint
stripping or deep concrete cleaning applications.
3. Clean a test area to satisfaction before
proceeding with the entire area, as stated
in Cleaning Recommendations.
4. This unit has several settings and adjustments
that effect the speed of cleaning and the
water force applied to cleaning. Good
guidelines to keep in mind are:
Wide Stream =
Quicker Coverage but
Lighter Cleaning.
Narrow Stream =
Deeper Cleaning but
Slower Coverage.
Page 10
Use Proper Pressure Washer Operation Techniques:
The machine may suddenly stop and require a rest
period from time to time; this is normal and does
not indicate a problem (See Troubleshooting
Section). However, certain operating techniques
may help reduce or even prevent the need for
such rest periods, increasing efficiency:
a. Do not release the trigger between sweeps.
Release the trigger as few times as possible
during use. Interrupted or sporadic spraying
will cause the unit to heat up quickly and
will increase the need for rest periods.
b. Make sure that all obstacles have been moved
and the entire area is ready before starting.
c. For small jobs, try to finish an entire portion
of the job before taking a break.
Cleaning Recommendations
5. Clean an inconspicuous test area first. Always begin
with the fan spray at a distance of about 3-5 feet from
the surface being cleaned to avoid damaging it. Clear
the test area of people and water-sensitive objects.
If a pressure washing detergent is to be used, apply
the detergent to this area as well. After cleaning this
area, switch off the pressure washer and inspect
the area carefully for any damage or discoloration.
If any damage is noted from the pressure setting,
use a lighter setting when cleaning the rest of the
area. If damage or discoloration is noted from
the detergent, do not use it when cleaning.
6. First, pass over the area with a light cleaning,
and then more thoroughly clean it.
For a vertical or sloped surface:
a. Wash from the top down.
b. If possible, direct the stream in the same
direction as the slope towards a draining
area. This will enable better drainage
and therefore better cleaning.
For a flat surface:
a. If a thin layer of water accumulates on
the surface, periodically use the stream to
direct this water towards the drainage.
b. After the major cleaning is done, sweep
the surface with the stream to help direct
loose debris toward the drainage.
7. If detergent is to be applied: Only use pressure
washing detergent in the soap dispenser; other
detergents will clog the dispenser. Do not add
detergent to the body of the pressure washer.
Spray the surface with detergent until evenly
covered, then turn off the machine and water
source, release pressure, and remove the soap
dispenser. Allow the detergent several minutes to
sit and soak into the work surface; this will improve
For technical questions, please call 1-800-444-3353.
SKU 68333
cleaning efficiency. Turn on the water source and
power, and rinse off all detergent completely.
8. Hold the Water Gun at about a 45° angle and
steadily sweep the stream back and forth; if a
severe, head-on angle is used, dirt may imbed
in the surface being cleaned. Follow a steady,
consistent pace during cleaning; this will help prevent
stripes or discoloration afterwards. If streaking or
uneven cleaning is noted at the end of a project,
go over the edges of the streaks with a wide fan
pattern to help blend these lighter areas in.
SKU 68333
9. If several different surfaces are to be cleaned,
be careful not to damage any of the less solid
surfaces while trying to clean the harder ones.
This is especially a concern when cleaning tile and
grout, bricks and mortar, or stones and mortar.
10. If wood is being cleaned, be careful to avoid damage.
Wood will usually require resurfacing (Sanding)
and re-coat with a surface protectant (wood, stain,
varnish) after it has dried. Try to avoid leaving water
on a wooden surface; doing so can harm the surface.
For technical questions, please call 1-800-444-3353.
Page 11
Maintenance and Servicing
To prevent serious injury from
accidental operation:
Turn the Power Switch of the tool off, unplug the
tool from its electrical outlet, shut off the water
supply and safely discharge all residual water
pressure from the unit before performing any
inspection, maintenance, or cleaning procedures.
To prevent serious injury
from tool failure:
Do not use damaged equipment. If abnormal
noise or vibration occurs, have the
problem corrected before further use.
Cleaning, Maintenance,
and Lubrication
1. Before each use, inspect the general condition
of the Pressure Washer. Check for loose screws,
misalignment or binding of moving parts, damaged
electrical wiring, damaged High Pressure Hose,
damaged accessories, and any other condition that
may affect its safe operation. If abnormal noise or
vibration occurs, have the problem corrected before
further use. Do not use damaged equipment.
any remaining water on all parts and fittings.
Remove mineral deposits from the nozzle using
a thin, stiff wire. The more minerals that are
dissolved in the water (the harder the water)
you use, the more often mineral buildup will
need to be cleaned out from inside nozzle.
3. In areas that have hard water (water rich in minerals
such as calcium) the unit will need to be cleaned
periodically to remove calcium buildup which can clog
the system. To clean off calcium buildup: Unplug the
unit and lay it face down. Fill the body at the water
inlet fitting with calcium remover and allow at least 5
hrs for calcium deposit to break down. Rinse and dry.
4. STORAGE: When storing, empty the Pressure
Washer of water. Frost will damage the Pressure
Washer if the unit contains water. Store the Pressure
Washer in a dry, frost-free room. Flush the unit with
automotive antifreeze prior to long-term storage.
Dispose of antifreeze according to local ordinances.
5.
WARNING! If the supply cord or GFCI unit
of this power tool is damaged, it must be
replaced only by a qualified service technician.
2. To clean, remove excess water from the Pump by
tipping the unit to drain any remaining water from
the inlet and outlet fittings. Drain the Detergent
Dispenser and flush with running water. Use only a
clean cloth and mild detergent to clean the body of
the Pressure Washer. Do not use solvents.
Do not immerse any part of the tool in liquid. Dry off
Page 12
For technical questions, please call 1-800-444-3353.
SKU 68333
Troubleshooting
Problem
Possible Causes
Pressure Washer
will not start
1. Cord not connected.
2. No power at outlet.
Pressure Washer
Stops suddenly
3. GFCI circuit breaker tripped.
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
1. GFCI circuit breaker tripped.
2. Water leaking from housing.
Output pressure
varies
1. Not enough water supply.
2. Air in water supply.
3. Water Inlet Filter is clogged.
4. Extension Nozzle not
attached to Spray Gun.
5. Nozzle is clogged.
6. Nozzle has mineral build up.
7. Garden hose is too long.
Trigger does
not depress
Detergent will
not dispense
Performance
decreases over time
8. Internal valves or seals may
be worn or sticking.
Safety lock is still engaged.
Incorrect detergent type.
Clogged with mineral deposits.
Likely Solutions
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If
breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Press reset button on GFCI unit on cord.
4. Have a qualified technician service tool.
1. Press reset button on GFCI unit on cord.
2. SHOCK HAZARD! IMMEDIATELY
discontinue use. Have the unit repaired by
a qualified technician before further use.
1. Check water supply hose for kinks, leaks,
or blockage. Open faucet all the way.
2. Check that all connections are tight.
3. Remove Filter and clean.
4. Pressure is created by the Nozzle, not the
Spray Gun. Attach Extension Nozzle to unit.
5. Remove Nozzle and clean.
6. Remove Nozzle and clean with vinegar.
7. Recommended garden hose length is
20 to 50 feet, or 30 feet if using well
water. Shorten the length of the garden
hose if needed to increase pressure.
8. Have a qualified technician service tool.
Press in on the release button on the bottom of
the Spray Gun Handle to release the Safety Lock.
Check that the detergent is the recommended
type of detergent. Clean out dispenser and
replace with correct type if needed.
Clean unit with a de-mineralizing solution such
as vinegar or other aqueous acidic cleaner.
Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power
supply before service.
SKU 68333
For technical questions, please call 1-800-444-3353.
Page 13
Parts List and Assembly Diagram
PLEASE READ THE FOLLOWING CAREFULLY
The manufacturer and/or distributor has provided the parts list and assembly diagram
in this manual as a reference tool only. Neither the manufacturer or distributor
makes any representation or warranty of any kind to the buyer that he or she is
qualified to make any repairs to the product, or that he or she is qualified to replace
any parts of the product. In fact, the manufacturer and/or distributor expressly
states that all repairs and parts replacements should be undertaken by certified and
licensed technicians, and not by the buyer. The buyer assumes all risk and liability
arising out of his or her repairs to the original product or replacement parts
thereto, or arising out of his or her installation of replacement parts thereto.
Parts List
Part
1
2
3
4
5
8
9
10
11
12
16
21
22
M
M1
Description
Body (right and left set)
Handle
Power Switch
Power Cord with GFCI
Inlet Water Filter
Wheels Kit
Motor Conveyor
Base
High Pressure Hose
Spray Gun
Extension Nozzle
Soap Nozzle
Soap Dispenser
Motor Assembly
Motor
Qty
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Part
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
M13
M15
M16
Description
Bearing 3047
Pin
Plate Assembly
Thrust Bearing 35x55x12
Piston Kit
O-Ring
Head Valve Kit
Head
O-Ring Water Seal
O-Ring
Oil Seals
Valve Guide
Piston Body Guide
Valve
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14
For technical questions, please call 1-800-444-3353.
SKU 68333
Parts List and Assembly Diagram
Assembly Diagram
2
9
1
1
5
3
12
16
4
21
M
11
10
22
8
M
OIL:
SAE 15/W40
gr. 70
M1
M2
M3 M4
M5
M6
M16
M8
M9
M13
M15
M7
M12
SKU 68333
M11
M10
For technical questions, please call 1-800-444-3353.
Page 15
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship
for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other
warranties, express or implied, including the warranties of merchantability and fitness.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353