Harbor Freight Tools Solar LED Flagpole Light Product manual

Important Safety Information
Installation Precautions
1. Install only according to these
instructions. Improper installation
can create hazards.
2. Wear ANSI-approved safety goggles
and heavy-duty work gloves
during installation.
3. Keep installation area clean and well lit.
4. Keep bystanders out of the
area during installation.
5. Do not install when tired or when
under the influence of alcohol,
drugs or medication.
6. Verify Pole Clamps are securely
tightened. Do not use if
Clamps are damaged.
Use Precautions
1. Do not hang anything from or on light.
2. This product is not a toy. Do not allow
children to play with or near this item.
3. Use as intended only.
4. Inspect before every use; do not use
if parts are loose or damaged.
5. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.
1. Remove the screws. Remove the Solar
Panel Cover from the Battery Housing.
2. Remove the tab at the end of the
batteries so the light can function.
NOTICE: Be careful that the wire
connecting the Solar Panel Cover
is not pulled and disconnected.
3. Place the Solar Panel Cover
back onto the Battery Housing,
and attach it with screws.
4. Loosen the screws on the two
Clamp Supports and open the Clamps.
Page 2
5. Slide the Clamps around the flagpole
at the desired height, making sure that
the Spotlight faces the flag and that the
Solar Panel Cover is in direct sunlight.
6. Tighten the Clamps until the Light is
securely fastened to the flagpole.
7. Loosen the Knobs and adjust
the Light and Solar Panel as desired.
Tighten the Knobs.
8. Slide the Switch to ON.
9. The Solar Light is now set to work.
Sunlight will recharge the
Batteries during daylight hours,
and light will turn on at night.
For technical questions, please call 1-800-444-3353.
Item 60555
Battery Replacement
Replace the rechargeable batteries at least every 12 months.
1.
Loosen the Clamps and remove
the Light from the flagpole.
2.
Slide the Switch to OFF.
3.
Remove the screws. Remove the Solar
Panel Cover from the Battery Housing.
NOTICE: Use care when removing
Solar Panel Cover so as to avoid
pulling on the wire between the
Battery Housing and the Spotlight.
4.
Remove and properly recycle old
Batteries. NI-CD BATTERIES MUST
BE RECYCLED OR DISPOSED OF
PROPERLY. Do not short, incinerate
or open batteries.
5.
Install two new, fully charged
‘AA’ NiCd batteries, making sure
the follow the indicated polarity.
6.
Place the Solar Panel Cover
back onto the Battery Housing,
and attach it with screws.
7.
Reinstall the Light onto the flagpole.
Parts List and Diagram
Part
Description
1
2
3
4
Qty.
Main Asm.
Solar Panel Cover
Clamp
‘AA’ NiCd Battery
1
1
2
2
Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.
2
4
3
1
Item 60555
For technical questions, please call 1-800-444-3353.
Page 3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST
AND INSTALLATION DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353